ACS108 [ETC]
AC LINE SWITCH ; AC线路开关\n®
ACS108-5Sx
ASD™
AC Switch Family
AC LINE SWITCH
MAIN APPLICATIONS
■
AC on-off static switching in appliance &
industrial control systems
■
Drive of low power high inductive or resistive
loads like:
- relay, valve, solenoid, dispenser
- pump, fan, micro-motor
- low power lamp bulb, door lock
OUT
COM
G
FEATURES
TO-92
■
■
■
■
■
■
■
Blocking voltage: VDRM / VRRM = 500V
Clamping voltage: VCL = 600V
Nominal current: IT(RMS) = 0.8 A
Gate triggering current : IGT < 10 mA
Triggering current is sourced by the gate
Switch integrated driver
ACS108-5SA
COM
OUT
COM
Drive reference COM connected to the SOT-223
tab
G
BENEFITS
■
Needs no external overvoltage protection.
Enables the equipment to meet IEC61000-4-5
standard.
SOT-223
ACS108-5SN
■
■
■
Allows straightforward connection of several
SOT-223 devices on the same cooling pad.
Reduces the switch component count by up to
80%.
FUNCTIONAL DIAGRAM
■
■
Interfaces directly with the microcontroller.
Eliminates any stressing gate kick back on the
microcontroller.
OUT
DESCRIPTION
ACS108
The ACS108 belongs to the AC line switches built
around the ASD™ concept. This high performance
device is able to control an 0.8 A load device.
S
The ACS™ switch embeds a high voltage
clamping structure to absorb the inductive
turn-off energy and a gate level shifter driver to
separate the digital controller from the main
switch. It is triggered with a negative gate current
flowing out of the gate pin.
ON
D
For further technical information, please refer to
AN1172 the Application note.
COM
G
ASD and ACS are a trademarks of STMicroelectronics.
October 2001 - Ed: 6C
1/8
ACS108-5Sx
ABSOLUTE RATINGS (limiting values)
Symbol
Parameter
Repetitive peak off-state voltage
Value
Unit
VDRM /
VRRM
Tj = 125 °C
500
V
IT(RMS)
RMS on-state current full cycle sine
wave 50 to 60 Hz
TO-92
TO-92
Tlead = 75 °C
Tamb = 60 °C
Tamb = 75 °C
F =50 Hz
0.8
0.3
0.8
7.3
8
A
A
SOT-223
A
ITSM
dI/dt
Non repetitive surge peak on-state current
Tj initial = 25°C, full cycle sine wave
A
F =60 Hz
A
Critical rate of repetitive rise of on-state current
IG = 20mA with tr = 100ns
F =120 Hz
100
A/µs
note 1
VPP
Tstg
Tj
Non repetitive line peak pulse voltage
Storage temperature range
2
kV
°C
°C
°C
- 40 to + 150
- 30 to + 125
260
Operating junction temperature range
Maximum lead temperature for soldering during 10s
Tl
Note 1: according to test described by IEC61000-4-5 standard & Figure 3.
SWITCH GATE CHARACTERISTICS (maximum values)
Symbol
PG (AV)
IGM
Parameter
Average gate power dissipation
Value
Unit
W
0.1
1
Peak gate current (tp = 20µs)
A
VGM
Peak positive gate voltage (respect to the pin COM)
5
V
THERMAL RESISTANCES
Symbol
Parameter
Value
150
60
Unit
°C/W
°C/W
°C/W
°C/W
Rth (j-a)
Junction to ambient
TO-92
SOT-223 (*)
TO-92
Rth (j-l)
Rth (j-t)
Junction to lead for full AC line cycle conduction
Junction to tab for full AC line cycle conduction
60
SOT-223
25
2
(*) : with 5cm copper (e=35µm) surface under tab
ELECTRICAL CHARACTERISTICS
For either positive or negative polarity of pin OUT voltage respect to pin COM voltage excepted note 3
Symbol
IGT
Test Conditions
Values
10
Unit
mA
V
VOUT=12V RL=140Ω
VOUT=12V RL=140Ω
VOUT=VDRM RL=3.3kΩ
Tj=25°C
Tj=25°C
Tj=125°C
Tj=25°C
MAX.
MAX.
MIN.
TYP.
MAX.
TYP.
MAX.
MAX.
MAX.
MAX.
MIN.
MIN.
MIN.
TYP.
VGT
VGD
IH
1
0.15
25
V
IOUT= 100mA gate open
mA
mA
mA
mA
V
60
IL
IG= 20mA
Tj=25°C
30
65
VTM
IOUT = 1.1A tp=500µs
Tj=25°C
Tj=25°C
Tj=125°C
Tj=110°C
Tj=110°C
Tj=110°C
Tj=25°C
1.3
2
IDRM
IRRM
VOUT = VDRM
VOUT = VRRM
µA
200
500
0.1
0.3
600
µA
dV/dt
(dI/dt)c
(dI/dt)c*
VCL
V
OUT=400V gate open
V/µs
A/ms
A/ms
V
(dV/dt)c=10V/µs
(dV/dt)c = 15V/µs Iout < 0 (note 3)
ICL = 1mA tp=1ms
2/8
ACS108-5Sx
AC LINE SWITCH BASIC APPLICATION
The ACS108 device is well adapted to washing machines, dishwashers, tumble driers, refrigerators, water
heaters and cookware. It has been especially designed to switch ON and OFF low power loads such as
solenoids, valves, relays, dispensers, micro-motors, fans, pumps, door locks and low power lamp bulbs.
Pin COM:
Pin G:
Common drive reference to connect to the power line neutral
Switch Gate input to connect to the digital controller through the resistor
Switch Output to connect to the Load
Pin OUT:
The ACS™ switch is triggered with a negative gate current flowing out of the gate pin G. It can be driven di-
rectly by the digital controller through a resistor as shown on the typical application diagram. No protection
devices are required between the gates and common terminals.
The SOT-223 version allows several ACS108 devices to be connected on the same cooling PCB pad
which is the COM pin : this cooling pad can be then reduced, and the printed circuit layout is simplified.
In appliance systems, the ACS108 switch intends to drive low power load in full cycle ON / OFF mode. The
turn off commutation characteristics of these loads can be classified in 3 groups as shown in Table 1.
Thanks to its thermal and turn-off commutation characteristics, the ACS108 switch drives a load, such as
door lock, lamp, relay, valve and micro motor, up to 0.2 A without any turn-off aid circuit. Switching off the
ACS within one full AC line cycle will extend its current up to 0.8 A on resistive load.
Table 1: Load grouping versus their turn off commutation requirement (230V AC applications).
Load IRMS
Current
TURN-FF
DELAY
(dI/dt)c
(dV/dt)c
POWER
FACTOR
LOAD
(A/ms)
(V/µs)
(A)
(ms)
<10
Door Lock Lamp
< 0.3
< 0.8
< 0.1
1
1
0.15
0.4
0.15
0.15
< 5
< 20
< 10
Relay Valve
Dispenser
> 0.7
< 0.05
Micro-motor
Pump Fan
< 0.2
< 0.6
> 0.2
> 0.2
< 0.1
< 0.3
< 10
< 10
< 10
< 20
TYPICAL APPLICATION DIAGRAM
LOAD
L
AC
L
MAINS
N
R
OUT
S
ACS108
ON
D
COM
G
ST 72 MCU
- Vcc
3/8
ACS108-5Sx
HIGH INDUCTIVE SWITCH-OFF OPERATION
At the end of the last conduction half-cycle, the load current reaches the holding current level IH, and the
ACS™ switch turns off. Because of the inductance L of the load, the current flows through the avalanche
diode D and decreases linearly to zero. During this time, the voltage across the switch is limited to the
clamping voltage VCL.
The energy stored in the inductance of the load depends on the holding current IH and the inductance (up to
10 H); it can reach about 20 mJ and is dissipated in the clamping section that is especially designed for that
purpose.
Fig. 2: ACS108 switch static characteristic.
Fig. 1: Turn-off operation of the ACS108 switch
with an electro valve: waveform of the gate current
IG, pin OUT current IOUT & voltage VOUT
.
IOUT
IOUT
(10 mA/div)
VCL = 650V
IH
IH
VOUT
VCL
VOUT
(200V/div)
Time (400µs/div)
AC LINE TRANSIENT VOLTAGE RUGGEDNESS
The ACS108 switch is able to safely withstand the AC line transient voltages either by clamping the low en-
ergy spikes or by breaking over under high energy shocks.
The test circuit in Figure 4 is representative of the final ACS™ application and is also used to stress the
ACS™ switch according to the IEC61000-4-5 standard conditions. Thanks to the load, the ACS™ switch
withstands the voltage spikes up to 2 kV above the peak line voltage. It will break over safely even on resis-
tive load where the turn-on current rise is high as shown in Figure 4. Such non-repetitive testing can be
done 10 times on each AC line voltage polarity.
Fig. 3: Overvoltage ruggedness test circuit for resistive
and inductive loads according to IEC61000-4-5
standard.
Fig. 4: Current and voltage of the ACS™ during
IEC61000-4-5 standard test with a 150Ω - 10µH
load & VPP = 2kV.
R = 150Ω, L = 5µH, VPP = 2kV.
Vout (200 V/div)
R
L
Iout (2 A/div)
OUT
AC LINE &
SURGE VOLTAGE
GENERATOR
ACSxx
S
dI/dt = 100 A/µs
V
AC + VPP
ON
D
COM
G
RG= 220Ω
4/8
ACS108-5Sx
Fig. 6: RMS on-state current versus ambient
temperature.
Fig. 5: Maximum power dissipation versus RMS
on-state current.
P(W)
IT(RMS)(A)
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
ACS108-5SA (TO92, Tamb=Tlead)
ACS108-5SN with 5cm² copper surface under tab
ACS108-5SA (TO92)
0.1
0.0
Tamb(°C)
0.1
0.0
IT(RMS)(A)
0.3 0.4 0.5
0
10 20 30 40 50 60 70 80 90 100 110 120 130
0.0
0.1
0.2
0.6
0.7
0.8
Fig. 7-1: Relative variation of thermal impedance
junction to ambient versus pulse duration
(ACS108-5SA) (TO-92).
Fig. 7-2: Relative variation of thermal impedance
junction to ambient versus pulse duration
(ACS108-5SN) (SOT-223).
Zth(j-a) / Rth(j-a)
Zth(j-a) / Rth(j-a)
1.00
1.00
0.10
0.10
tp(s)
tp(s)
0.01
0.01
1E-3
1E-2
1E-1
1E+0
1E+1
1E+2 5E+2
1E-3
1E-2
1E-1
1E+0
1E+1
1E+2 5E+2
Fig. 8: Relative variation of gate trigger current
versus junction temperature.
Fig. 9: Relative variation of holding and latching
current versus junction temperature.
IH,IL [Tj] / IH,IL [Tj=25°C]
IGT [Tj] / IGT [Tj=25°C]
2.0
3.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
2.5
2.0
1.5
1.0
0.5
0.2
Tj(°C)
40 60
Tj(°C)
0.0
-40
0.0
-20
0
20
80
100
120
140
-40
-20
0
20
40
60
80
100 120 140
5/8
ACS108-5Sx
Fig. 11: Non-repetitive surge peak on-state
current for a sinusoidal pulse with width tp<10ms,
and corresponding value of I2t.
Fig. 10: Non repetitive surge peak on-state current
versus number of cycles.
ITSM(A)
ITSM(A),I²t(A²s)
9
100.0
Tj initial=25°C
ITSM
8
t=20ms
7
One cycle
6
10.0
1.0
Tj initial=25°C
Non repetitive
5
4
Tamb=25°C
Repetitive
3
2
I²t
tp(ms)
1
Number of cycles
0
0.1
1
10
100
1000
0.01
0.10
1.00
10.00
Fig. 12: On-state characteristics (maximum values).
Fig. 13: Thermal resistance junction to ambient
versus copper surface under tab (Epoxy printed
circuit board FR4, copper thickness: 35µm).
ITM(A)
Rth(j-a) (°C/W)
5.00
130
120
110
100
90
1.00
0.10
80
70
60
50
40
Tj max.:
Vto = 0.9 V
Rd = 300 mΩ
30
20
VTM(V)
S(Cu) (cm²)
10
0
0.01
0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Fig. 14: Relative variation of critical (dI/dt)c versus
junction temperature.
(dI/dt)c [Tj] / (dI/dt)c [Tj=110°C]
3.0
2.5
2.0
1.5
1.0
0.5
Tj(°C)
0.0
0
10 20 30 40 50 60 70 80 90 100 110 120
6/8
ACS108-5Sx
ORDERING INFORMATION
ACS 1
08 -
5
S
A
-TR
Switch
Number
A = TO-92
N = SOT-223
VDRM
5 = 500V
AC Switch
-TR = SOT-223
Tape & Reel
Gate
Sensitivity
S = 10mA
ITRMS
08 = 0.8A
PACKAGE MECHANICAL DATA
SOT-223
DIMENSIONS
Millimeters Inches
Min. Typ. Max. Min. Typ. Max.
REF.
A
c
V
A1
A
1.80
0.071
0.004
B
A1 0.02
0.10 0.001
e1
D
B
0.60 0.70 0.85 0.024 0.027 0.033
PIN
1
DESCRIPTION
GATE BASE
B1 2.90 3.00 3.15 0.114 0.118 0.124
B1
c
D
e
0.24 0.26 0.35 0.009 0.010 0.014
6.30 6.50 6.70 0.248 0.256 0.264
2
DRAIN
COLLECTOR
EMITTER
SOURCE
DRAIN
3
4
COLLECTOR
2.3
4.6
0.090
0.181
4
2
H
E
e1
E
1
3
3.30 3.50 3.70 0.130 0.138 0.146
6.70 7.00 7.30 0.264 0.276 0.287
10° max
H
V
e
PACKAGE MECHANICAL DATA
SOT-223
Recommended soldering pattern SOT-223
7/8
ACS108-5Sx
PACKAGE MECHANICAL DATA
TO-92 (Plastic)
DIMENSIONS
Millimeters
Min. Typ. Max. Min. Typ. Max.
REF.
Inches
A
a
A
B
C
D
E
F
a
1.35
0.053
0.100
4.70
0.185
B
C
2.54
4.40
0.173
0.500
12.70
F
D
E
3.70
0.45
0.146
0.017
OTHER INFORMATION
Ordering type
ACS108-5SA
Marking
ACS08/5S
ACS08/5S
ACS/085S
Package
TO-92
Weight
Base qty
2500
Delivery mode
Bulk
0.2 g
0.2 g
ACS108-5SA-TR
ACS108-5SN
TO-92
2000
Tape & reel
Tape & reel
SOT-223
0.12 g
1000
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of
use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to
change without notice. This publication supersedes and replaces all information previously supplied.
STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written ap-
proval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
© 2001 STMicroelectronics - Printed in Italy - All rights reserved.
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia
Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
http://www.st.com
8/8
相关型号:
©2020 ICPDF网 联系我们和版权申明