ACS108-6SN [STMICROELECTRONICS]
AC switch family Transient voltage protected AC Switch (ACS); AC开关系列瞬态电压保护交流开关( ACS )![ACS108-6SN](http://pdffile.icpdf.com/pdf1/p00122/img/icpdf/ACS1086S_669331_icpdf.jpg)
型号: | ACS108-6SN |
厂家: | ![]() |
描述: | AC switch family Transient voltage protected AC Switch (ACS) |
文件: | 总11页 (文件大小:174K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
ACS108-6S
AC switch family
Transient voltage protected AC Switch (ACS™)
Main product characteristics
IT(RMS)
VDRM/VRRM
IGT
0.8 A
600 V
10 mA
COM
COM
G
COM
G
OUT
OUT
■ Overvoltage protection by crowbar technology
■ High noise immunity - static dV/dt > 500 V/µs
TO-92
ACS108-6SA
SOT-223
ACS108-6SN
Applications
Description
■ AC ON/OFF static switching in appliances and
industrial control systems
The ACS108-6S belongs to the AC line switch
family. This high performance switch can control a
load of up to 0.8A.
■ Drive of low power high inductive or resistive
loads like:
– relay, valve, solenoid,
– dispenser, door lock
– pump, fan, micro-motor
The ACS108-6S switch includes an overvoltage
crowbar structure to absorb the overvoltage
energy, and a gate level shifter driver to separate
the digital controller from the main switch. It is
triggered with a negative gate current flowing out
of the gate pin.
Benefits
■ Needs no external protection snubber or
varistor.
Functional diagram
■ Enables equipment to meet IEC 61000-4-5.
■ Reduces component count by up to 80%.
■ Interfaces directly with the micro-controller.
OUT
■ Common package tab connection supports
connection of several alternating current
switches (ACS) on the same cooling pad.
■ Integrated structure based on ASD(a)
G
technology
Order code
COM
Part number
Marking
ACS108-6SA
ACS108-6SA-TR
ACS108-6SA-AP
ACS108-6SN-TR
ACS1086S
ACS1086S
ACS1086S
ACS1086S
COM Common drive reference to connect to the
mains
OUT Output to connect to the load.
G
Gate input to connect to the controller through
gate resistor
TM: ACS is a trademark of STMicroelectronics
a. ASD: Application Specific Devices
June 2006
Rev 2
1/11
www.st.com
Characteristics
ACS108-6S
1
Characteristics
Table 1.
Symbol
Absolute maximum ratings (Tamb = 25 °C, unless otherwise specified)
Parameter Value
Unit
TO-92
Tlead = 75 °C
Tamb = 75 °C
Tamb = 61 °C
t = 16.7 ms
t = 20 ms
0.8
IT(RMS) RMS on-state current (full sine wave)
SOT-223
TO-92
A
0.45
7.6
f = 60 Hz
f = 50 Hz
Non repetitive surge peak on-state current
ITSM
A
(full cycle sine wave, Tj initial = 25 °C)
7.3
I²t
I²t Value for fusing
tp = 10 ms
0.38
A2s
Critical rate of rise of on-state current
IG = 2xIGT, tr ≤ 100 ns
Non repetitive line peak mains voltage(1)
dI/dt
f = 120 Hz
tp = 20 µs
Tj = 125 °C
100
A/µs
VPP
IGM
Tj = 25 °C
Tj = 125 °C
Tj = 125 °C
Tj = 125 °C
2
1
kV
A
Peak gate current
VGM
Peak positive gate voltage
10
0.1
V
PG(AV) Average gate power dissipation
W
Tstg
Tj
Storage junction temperature range
Operating junction temperature range
-40 to +150
-30 to +125
°C
1. according to test described by IEC 61000-4-5 standard and Figure 16
Table 2.
Symbol
Electrical characteristics (Tj = 25 °C, unless otherwise specified)
Test conditions
Quadrant
Value
Unit
(1)
IGT
VGT
II - III
II - III
II - III
MAX
MAX
MIN
MAX
MAX
MIN
MIN
MIN
10
1
mA
VOUT = 12 V, RL = 33 Ω
V
VGD
VOUT = VDRM, RL =3.3 kΩ, Tj = 125 °C
IOUT = 100 mA
0.15
25
V
(2)
IH
mA
mA
V/µs
A/ms
V
(2)
IL
IG = 1.2 x IGT
30
dV/dt (2)
(dI/dt)c (2)
VCL
VOUT = 67% VDRM, gate open, Tj = 125 °C
500
0.3
650
Without snubber (15 V/µs), turn-off time ≤ 20 ms, Tj = 125 °C
ICL = 0.1 mA, tp = 1 ms, Tj = 125 °C
1. minimum I is guaranteed at 10% of I max
GT
GT
2. for both polarities of OUT referenced to COM
2/11
ACS108-6S
Characteristics
Table 3.
Symbol
Static electrical characteristics
Test conditions
Value
Unit
(1)
VTM
ITM= 1.1 A, tp = 500 µs
Tj = 25 °C
Tj = 125 °C
Tj = 125 °C
Tj = 25 °C
Tj = 125 °C
MAX
MAX
MAX
1.3
0.90
300
2
V
V
(1)
VTO
(1)
RD
mΩ
µA
mA
IDRM
IRRM
VOUT = 600 V
MAX
0.2
1. for both polarities of OUT referenced to COM
Table 4.
Symbol
Rth (j-l)
Rth (j-l)
Thermal resistance
Parameter
Value
Unit
Junction to lead (AC)
Junction to tab (AC)
TO-92
60
25
SOT-223
TO-92
°C/W
150
60
Rth (j-a)
Junction to ambient
S = 5 cm²
Figure 2.
SOT-223
Figure 1.
Maximum power dissipation
vs RMS on-state current (full cycle)
RMS on-state current vs ambient
temperature (full cycle)
P (W)
IT(RMS) (A)
0.90
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0.80
0.70
0.60
0.50
0.40
0.30
0.20
0.10
0.00
ACS108-6SN (with 5cm² copper surface under tab)
ACS108-6SA
180°
Tamb °C
IT(RMS) (A)
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0
25
50
75
100
125
3/11
Characteristics
ACS108-6S
Figure 3.
Relative variation of junction to
Figure 4.
Relative variation of gate trigger
ambient thermal impedance vs
pulse duration and package
current, holding current and
latching current vs junction
temperature
K=[Zth(j-a)/Rth(j-a)
]
I
GT, I
H, I [T
j] / I
GT, IH, IL
[T =25°
C]
L
j
2.8
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
1.E+00
IGT
1.E-01
TO-92
IL & IH
SOT-223
tP (S)
Tj(°C)
10 20 30 40 50 60 70 80 90 100 110 120 130
1.E-02
1.E-03
-40 -30 -20 -10
0
1.E-02
1.E-01
1.E+00
1.E+01
1.E+02
1.E+03
Figure 5.
Non repetitive surge peak on-state Figure 6.
current vs number of cycles
Non repetitive surge peak on-state
current for a sinusoidal pulse with
width tp<10 ms, and corresponding
value of I²t (Tj initial = 25 °C
I
TSM(A)
ITSM(A), I²t (A²
s)
10
9
8
7
6
5
4
3
2
1
0
1.E+03
1.E+02
1.E+01
1.E+00
1.E-01
Tj initial=25°C
t=20ms
One cycle
Non repetitive
ITSM
T
j
initial = 25 °C
Repetitive
amb = 75 °C
T
I²t
tp(ms)
Number of cycles
0.01
0.10
1.00
10.00
1
10
100
1000
4/11
ACS108-6S
Figure 7.
Characteristics
On-state characteristics (maximal Figure 8.
values)
SOT-223 junction to ambient
thermal resistance versus copper
surface under tab (PCB FR4,
copper thickness 35 µm)
I
TM(A)
10.00
1.00
0.10
0.01
140
120
100
Tj max.:
to= 0.9 V
SOT-223
V
Rd= 300 mΩ
Tj=125°C
80
60
40
20
0
Tj=25°C
SCU(cm²)
VTM(V)
2.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0.0
0.5
1.0
1.5
2.5
3.0
3.5
4.0
Figure 9.
Relative variation of critical rate of Figure 10. Relative variation of critical rate of
decrease of main current (di/dt)c
versus junction temperature
decrease of main current (di/dt)c vs
(dV/dt)c, with turn-off time < 20 ms
)
(dI/dt)c [ (dV/dt)c ] / Specified (dI/dt
c
(dI/dt)c [Tj] / (dI/dt)c [Tj=125 °C]
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
12
11
10
9
Vout=300 V
Vout = 400 V
8
7
6
5
4
3
2
(dV/dt)c (V/µs)
1
Tj (°C)
0
0
10
20
30
40
50
60
70
80
90 100 110 120 130
0.1
1
10
100
Figure 11. Relative variation of static dV/dt
versus junction temperature
Figure 12. Relative variation of the maximal
clamping voltage versus junction
temperature (min value)
VCL [Tj] / VDRM
1.20
C]
T =125°
] / dV/dt [
dV/dt [Tj
j
8
7
6
5
4
3
2
1
0
Vout=400V
1.10
1.00
0.90
0.80
0.70
0.60
Tj(°C)
75
Tj(°C)
0.50
25
50
100
125
-25
0
25
50
75
100
125
5/11
AC line switch - basic application
ACS108-6S
2
AC line switch - basic application
The ACS108-6S switch is triggered by a negative gate current flowing from the gate pin G.
The switch can be driven directly by the digital controller through a resistor as shown in
Figure 13.
Thanks to its overvoltage protection and turn-off commutation performance, the ACS108-6S
switch can drive a small power high inductive load with neither varistor nor additional turn-off
snubber.
Figure 13. Typical application program
Valve
AC Mains
V
MCU
ss
Rg
ACS108-6S
Power supply
V
dd
2.1
Protection against overvoltage: the best choice is ACS
In comparison with standard triacs, which are not robust against surge voltage, the ACS108-
6S is over-voltage self-protected, specified by the new parameter VCL. This feature is useful
in two operating conditions: in case of turn-off of very inductive load, and in case of surge
voltage that can occur on the electrical network.
2.1.1
High inductive load switch-off: turn-off overvoltage clamping
With high inductive and low RMS current loads the rate of decrease of the current is very
low. An overvoltage can occur when the gate current is removed and the OUT current is
lower than IH.
As shown in Figure 14 and Figure 15, at the end of the last conduction half-cycle, the load
current decreases (1). The load current reaches the holding current level IH (2), and the
ACS turns off (3). The water valve, as an inductive load (up to 15 H), reacts as a current
generator and an overvoltage is created, which is clamped by the ACS (4). The current flows
through the ACS avalanche and decreases linearly to zero. During this time, the voltage
across the switch is limited to the clamping voltage VCL. The energy stored in the inductance
of the load is dissipated in the clamping section that is designed for this purpose. When the
energy has been dissipated, the ACS voltage falls back to the mains voltage value (5).
6/11
ACS108-6S
AC line switch - basic application
Figure 14. Effect of the switching off of a high Figure 15. Description of the different steps
inductive load - typical clamping
capability of ACS108-6S
during switching off of a high
inductive load
4
I OUT
VPEAK = V CL
1
IOUT
(5 mA/div)
3
3
2
VOUT
(200 V/div)
I H
4
1
VOUT
5
I H
VCL
2
5
100µs/div
2.1.2
AC line transient voltage ruggedness
The ACS108-6S switch is able to withstand safely the AC line transients either by clamping
the low energy spikes or by breaking over under high energy shocks, even with high turn-on
current rises.
The test circuit shown in Figure 16 is representative of the final ACS108-6S application, and
is also used to test the ACS switch according to the IEC 61000-4-5 standard conditions.
Thanks to the load limiting the current, the ACS108-6S switch withstands the voltage spikes
up to 2 kV above the peak line voltage. The protection is based on an overvoltage crowbar
technology. Actually, the ACS108-6S breaks over safely as shown in Figure 17. The
ACS108-6S recovers its blocking voltage capability after the surge (switch off back at the
next zero crossing of the current).
Such non-repetitive tests can be done 10 times on each AC line voltage polarity.
Figure 16. Overvoltage ruggedness test circuit Figure 17. Typical current and voltage
for resistive and inductive loads
with conditions equivalent to
IEC 61000-4-5 standards
waveforms across the ACS108-6S
during IEC 61000-4-5 standard test
VPEAK
I OUT
(2 A/div)
Surge generator
"1.2/50 waveform"
Model of the load
VOUT
Rgene
2
L
R
(200 V/div)
150
5µH
ACS108-6Sx
2.4 kV surge
Rg
220
200ns/div
7/11
Ordering information scheme
ACS108-6S
3
Ordering information scheme
ACS
1
08 - 6
S
A -TR
AC Switch series
Number of switches
Current
08 = 0.8 ARMS
Voltage
6 = 600 V
Sensitivity
S = 10 mA
Package
A = TO-92
N = SOT-223
Packing
TR = Tape and reel
AP = Ammopack (TO-92)
Blank = (TO-92) Bulk
(SOT-223) Tube
4
Package information
Table 5.
TO-92 Mechanical data
Dimensions
Millimeters
Min. Typ. Max. Min. Typ. Max.
Ref
Inches
A
A
B
C
D
E
F
a
1.35
0.053
a
4.70
0.185
B
C
2.54
0.100
4.40
0.173
0.500
D
E
F
12.70
3.70
0.50
0.146
0.019
8/11
ACS108-6S
Package information
Table 6.
SOT-223 Mechanical data
Dimensions
Ref.
Millimeters
Inches
Min. Typ. Max. Min. Typ. Max.
V
c
A
A
A1
B
1.80
0.071
A1
B
0.02
0.70
3.00
0.26
6.50
2.3
0.001
e1
0.60
2.90
0.24
6.30
0.80 0.024 0.027 0.031
3.10 0.114 0.118 0.122
0.32 0.009 0.010 0.013
6.70 0.248 0.256 0.264
0.090
D
B1
c
B1
D
4
E
H
e
1
2
3
e1
E
4.6
0.181
3.30
6.70
3.50
7.00
3.70 0.130 0.138 0.146
7.30 0.264 0.276 0.287
10° max
e
H
V
Figure 18. SOT-223 Footprint
3.25
1.32
5.16
7.80
1.32
2.30
0.95
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com.
9/11
Ordering information
ACS108-6S
5
Ordering information
Part number
Marking
Package
Weight
Base Qty Packing mode
ACS108-6SA
ACS108-6SA-TR
ACS108-6SA-AP
ACS108-6SN-TR
ACS1086S
ACS1086S
ACS1086S
ACS1086S
TO-92
TO-92
0.2 g
0.2 g
0.2 g
0.11 g
2500
2000
2000
1000
Bulk
Tape and Reel
Ammopack
Tape & reel
TO-92
SOT-223
6
Revision history
Date
Revision
Changes
05-Jan-2005
07-Jun-2006
1
2
Initial release.
Reformatted to current standard. Replaced Figure 9.
10/11
ACS108-6S
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED,
AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS,
NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR
SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
11/11
相关型号:
©2020 ICPDF网 联系我们和版权申明