F49L004UA-70NP [ESMT]
Flash Memory,;
| 型号： | F49L004UA-70NP |
| 厂家： | 
ELITE SEMICONDUCTOR MEMORY TECHNOLOGY INC. |
| 描述： | Flash Memory, |
| 文件： | 总46页 (文件大小：588K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
EFST
F49L004UA / F49L004BA
4 Mbit (512K x 8)
3V Only CMOS Flash Memory
1. FEATURES
z
z
z
Single supply voltage 2.7V-3.6V
Fast access time: 70/90 ns
Compatible with JEDEC standard
- Pinout, packages and software commands
compatible with single-power supply Flash
Low power consumption
z
Ready/Busy (RY/
)
BY
- RY/
output pin for detection of program or erase
BY
operation completion
End of program or erase detection
- Data polling
z
z
- Toggle bits
- 20mA typical active current
- 0.2uA typical standby current
z
z
Hardware reset
- Hardware pin(
RESET
to the read mode
Sector Protection /Unprotection
- Hardware Protect/Unprotect any combination of sectors
from a program or erase operation.
Low VCC Write inhibit is equal to or less than 2.0V
Boot Sector Architecture
- U = Upper Boot Sector
- B = Bottom Boot Sector
Packages available:
- 40-pin TSOPI
) resets the internal state machine
z
z
100,000 program/erase cycles typically
Command register architecture
- Byte programming (9us typical)
- Sector Erase(sector structure: one 16 KB, two 8 KB,
one 32 KB, and seven 64 KB)
Auto Erase (chip & sector) and Auto Program
- Any combination of sectors can be erased
concurrently; Chip erase also provided.
- Automatically program and verify data at specified
address
z
z
z
z
z
Erase Suspend/Erase Resume
- Suspend or Resume erasing sectors to allow the
read/program in another sector
- 32-pin PLCC
2. ORDERING INFORMATION
Part No
Boot
Speed
Package
Part No
Boot
Speed
Package
F49L004UA-70T
F49L004UA-70N
F49L004BA-70T
F49L004BA-70N
Upper
Upper
70 ns
70 ns
70 ns
70 ns
TSOPI
PLCC
TSOPI
PLCC
F49L004UA-90 T
F49L004UA-90N
F49L004BA-90T
F49L004BA-90N
Upper
Upper
90 ns
90 ns
90 ns
90 ns
TSOPI
PLCC
TSOPI
PLCC
Bottom
Bottom
Bottom
Bottom
3. GENERAL DESCRIPTION
The F49L004UA/ F49L004BA is a 4 Megabit, 3V only
CMOS Flash memory device organized as 512K bytes of
8 bits. This device is packaged in standard 40-pin TSOP
and 32-pin PLCC. It is designed to be programmed and
erased both in system and can in standard EPROM
programmers.
The F49L004UA/ F49L004BA features a sector erase
architecture. The device memory array is divided into one
16 Kbytes, two 8 Kbytes, one 32 Kbytes, and seven 64
Kbytes. Sectors can be erased individually or in groups
without affecting the data in other sectors. Multiple-sector
erase and whole chip erase capabilities provide the
flexibility to revise the data in the device.
With access times of 70 ns and 90 ns, the F49L004UA/
F49L004BA allows the operation of high-speed
microprocessors. The device has separate chip enable
The sector protect/unprotect feature disables both
program and erase operations in any combination of the
sectors of the memory. This can be achieved in-system or
via programming equipment.
, write enable
, and output enable
controls.
OE
WE
CE
EFST's memory devices reliably store memory data even
after 100,000 program and erase cycles.
A low VCC detector inhibits write operations on loss of
power. End of program or erase is detected by the
Ready/Busy status pin, Data Polling of DQ7, or by the
Toggle Bit I feature on DQ6. Once the program or erase
cycle has been successfully completed, the device
internally resets to the Read mode.
The F49L004UA/ F49L004BA is entirely pin and
command set compatible with the JEDEC standard for 4
Megabit Flash memory devices. Commands are written to
the command register using standard microprocessor
write timings.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
1/46
EFST
F49L004UA / F49L004BA
4. PIN CONFIGURATIONS
4.1 40-pin TSOP I
A17
40
1
A16
A15
A14
A13
A12
A11
A9
VSS
39
2
N C
38
3
N C
37
4
A10
36
5
DQ7
35
6
DQ6
34
7
DQ5
33
8
A8
DQ4
32
9
WE
RESET
N C
RY/BY
A18
A7
VCC
31
10
11
12
13
14
15
16
17
18
19
20
VCC
30
N C
29
DQ3
28
DQ2
27
DQ1
26
A6
DQ0
25
A5
OE
24
A4
VSS
23
A3
CE
22
A2
A0
21
A1
4.2 32-pin PLCC
4
3
2
1 32 31 30
A14
A13
A8
2 9
2 8
2 7
2 6
2 5
2 4
2 3
2 2
2 1
5
6
7
8
A7
A6
A5
A9
A4
A11
OE
A3
9
A2
10
11
12
13
A10
CE
A1
A0
DQ7
DQ0
14 15 16 17 18 19 20
4.3 Pin Description
Symbol
A0~A18
Pin Name
Address Input
Functions
To provide memory addresses.
To output data when Read and receive data when Write.
DQ0~DQ7
Data Input/Output
The outputs are in tri-state when OE or CE is high.
To activate the device when CE is low.
To gate the data output buffers.
Chip Enable
Output Enable
Write Enable
Reset
CE
OE
To control the Write operations.
WE
Hardware Reset Pin/Sector Protect Unprotect (for 40-TSOP)
RESET
Ready/Busy
To check device operation status(for 40 TSOP)
To provide power
RY/ BY
VCC
Power Supply
Ground
GND
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 2/46
EFST
F49L004UA / F49L004BA
5. SECTOR STRUCTURE
Table 1: F49L004UA Sector Address Table
Sector Address
Sector Size
Sector
Address range
(Kbytes)
A18 A17 A16 A15 A14 A13
SA10
SA9
SA8
SA7
SA6
SA5
SA4
SA3
SA2
SA1
SA0
16
8
7C000H-7FFFFH
7A000H-7BFFFH
78000H-79FFFH
70000H-77FFFH
60000H-6FFFFH
50000H-5FFFFH
40000H-4FFFFH
30000H-3FFFFH
20000H-2FFFFH
10000H-1FFFFH
00000H-0FFFFH
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
1
0
0
1
1
0
0
1
1
1
1
0
1
0
1
0
1
0
1
1
1
0
X
1
8
1
0
0
32
64
64
64
64
64
64
64
0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Table 2: F49L004BA Sector Address Table
Sector Address
A18 A17 A16 A15 A14 A13
Sector Size
(Kbytes)
Sector
Address range
SA10
SA9
SA8
SA7
SA6
SA5
SA4
SA3
SA2
SA1
SA0
64
64
64
64
64
64
64
32
8
70000H-7FFFFH
60000H-6FFFFH
50000H-5FFFFH
40000H-4FFFFH
30000H-3FFFFH
20000H-2FFFFH
10000H-1FFFFH
08000H-0FFFFH
06000H-07FFFH
04000H-05FFFH
00000H-03FFFH
1
1
1
1
0
0
0
0
0
0
0
1
1
0
0
1
1
0
0
0
0
0
1
0
1
0
1
0
1
0
0
0
0
X
X
X
X
X
X
X
1
X
X
X
X
X
X
X
X
1
X
X
X
X
X
X
X
X
1
0
8
0
1
0
16
0
0
X
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 3/46
EFST
F49L004UA / F49L004BA
6. FUNCTIONAL BLOCK DIAGRAM
CE
WRITE
PROGRAM / ERASE
HIGH VOLTAGE
CONTROL
INPUT
LOGIC
STATE
MACHING
(WSM)
OE
WE
RESET(for40-TSOP)
STATE
REGISTER
F49L004U(B)A
ADDRESS
LATCH
FLASH
ARRAY
ARRAY
SOURCE
HV
A0~A18
AND
BUFFER
COMMAND
DATA
DECODER
Y-PASS GATE
PGM
DATA
HV
SENSE
AMPLIFIER
COMMAND
DATA LATCH
PROGRAM
DATA LATCH
I / O BUFFER
DQ0~DQ7
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
4/46
EFST
F49L004UA / F49L004BA
7. FUNCTIONAL DESCRIPTION
7.1 Device operation
This section describes the requirements and use
of the device bus operations, which are initiated
through the internal command register. The
register is composed of latches that store the
command, address and data information needed
to execute the command. The contents of the
register serve as inputs to the internal state
machine. The state machine outputs dictate the
function of the device.
The F49L004UA/
F49L004BA features various bus operations as
Table 3.
Table 3. F49L004UA/F49L004BA Operation Modes Selection
ADDRESS
A8
A18 A12
A5
|
DESCRIPTION
DQ0~DQ7
OE
RESET
CE
WE
|
|
|
A9
A6
A1 A0
A13 A10
A7
A2
L, Vss±
0.3V(4)
Reset(3)
X
X
X
X
High Z
Read
L
L
L
L
H
H
H
L
H
H
H
AIN
AIN
X
Dout
DIN
Write
Output Disable
H
High Z
V
0.3V
CC±±
VCC±±
0.3V
Standby
X
X
X
High Z
Sector Protect(2)
L
L
H
H
X
L
L
X
VID
SA
SA
X
X
X
X
X
L
X
X
H
H
L
L
DIN
DIN
DIN
Sector Unprotect(2)
Temporary sector unprotect
Auto-select
VID
X
H
X
VID
AIN
See Table 4
Notes:
1. L= Logic Low = VIL, H= Logic High = VIH, X= Don't Care, SA= Sector Address, VID=11.5V to 12.5V.
AIN= Address In, DIN = Data In, Dout = Data Out.
2. The sector protect and unprotect functions may also be implemented via programming equipment.
3.
pin for 40-TSOP package type only.
RESET
4. See “Reset Mode” section.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
5/46
EFST
F49L004UA / F49L004BA
Table 4. F49L004UA/F49L004BA Auto-Select Mode (High Voltage Method)
ADDRESS
A8
DQ0~DQ7
A18
|
A12
|
DESCRIPTION
OE
RESET
CE
WE
|
A9
A3 A2 A1 A0
A13
A10
A4
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
H
H
H
H
H
H
H
H
H
H
H
X
X
X
X
X
X
X
X
X
VID
VID
VID
VID
VID
VID
VID
X
X
X
X
X
X
X
L
H
H
L
H
L
L
L
L
L
L
L
H
L
L
7FH
7FH
(Manufacturer ID:EFST)
X
H
L
L
7FH
X
L
8CH
(Device ID: F49L004UA)
(Device ID: F49L004BA)
Sector Protection Verify
X
X
X
X
X
X
X
H
H
X
B5H
X
B6H
SA
Code(2)
Notes :
1.Manufacturer and device codes may also be accessed via the software command sequence in Table 5.
2. Code=00H means unprotected.
Code =01H means protected.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 6/46
EFST
F49L004UA / F49L004BA
Reset Mode :
Hardware Reset (for 40-TSOP package)
valid addresses on the device address inputs produce
valid data on the device data outputs. The device remains
enabled for read access until the command register
contents are altered.
See “Read Command” section for more information.
Refer to the AC Read Operations table for timing
specifications and to Figure 5 for the timing diagram. ICC1
in the DC Characteristics table represents the active
current
When the
pin is driven low for at least a
RESET
period of tRP, the device immediately terminates any
operation in progress, tri-states all output pins, and
ignores all read/write commands for the duration of the
pulse. The device also resets the internal state
RESET
machine to reading array data. The operation that was
interrupted should be reinitiated later once the device is
ready to accept another command sequence, to ensure
the data integrity.
specification for reading array data.
The current is reduced for the duration of the
RESET
is held at VSS±0.3V, the device
pulse. When
RESET
draws CMOS standby current (ICC4). If
Write Mode
is held
RESET
To write a command or command sequence (which
includes programming data to the device and erasing
at VIL but not within VSS±0.3V, the standby current will
be greater.
sectors of memory), the system must drive
and
CE
WE
to VIL, and
to VIH. The “Program Command” section
OE
The
pin may be tied to system reset circuitry.
RESET
has details on programming data to the device using
standard command sequences.
A system reset would thus reset the Flash memory,
enabling the system to read the boot-up firm-ware from
the Flash memory.
An erase operation can erase one sector, multiple
sectors, or the entire device. Tables 1 and 2 indicate the
address space that each sector occupies. A “sector
address” consists of the address bits required to uniquely
select a sector. The “Software Command Definitions”
section has details on erasing a sector or the entire chip,
or suspending/resuming the erase operation.
If
is asserted during a program or erase
RESET
embedded algorithm operation, the RY/
pin remains
BY
a "0" (busy) until the internal reset operation is
complete, which requires a time of tREADY (during
Embedded Algorithms). The system can thus monitor
RY/
to determine whether the reset operation is
BY
complete.
When the system writes the auto-select command
sequence, the device enters the auto-select mode. The
system can then read auto-select codes from the internal
register (which is separate from the memory array) on
DQ7–DQ0. Standard read cycle timings apply in this
mode. Refer to the Auto-select Mode and Auto-select
Command sections for more information. ICC2 in the DC
Characteristics table represents the active current
specification for the write mode. The “AC Characteristics”
section contains timing specification tables and timing
diagrams for write operations.
If
is asserted when a program or erase
RESET
operation is not executing , i.e. the RY/
reset operation is completed within a time of tREADY (not
during Embedded Algorithms). The system can read
data after tRH when the
Refer to the AC Characteristics tables for Hardware
Reset section.
is “1”, the
BY
pin returns to VIH.
RESET
Read Mode
Automatic Sleep Mode
To read array data from the outputs, the system must
The automatic sleep mode minimizes Flash device
energy consumption. The device automatically enables
this mode when addresses remain unchanged for over
250ns ns. The automatic sleep mode is independent of
drive the
and
pins to VIL.
is the power
CE
OE
CE
control and selects the device.
is the output
OE
control and gates array data to the output pins.
WE
the
,
, and
control signals. Standard
OE
WE
CE
should remain at VIH. The internal state machine is set
for reading array data upon device power-up, or after a
hardware reset. This ensures that no spurious
alteration of the memory content occurs during the
power transition.
address access timings provide new data when
addresses are changed. While in sleep mode, output
data is latched and always available to the system. ICC4 in
the DC Characteristics table represents the automatic
sleep mode current specification.
No command is necessary in this mode to obtain array
data. Standard microprocessor’s read cycles that assert
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
7/46
EFST
F49L004UA / F49L004BA
Temporary Sector Unprotect Mode
This feature allows temporary unprotection of previously
protected sector to change data in-system. This mode is
un-protected and can be programmed or erased by
selecting the sector addresses. Once VID is removed from
activated by setting the
pin to VID(11.5V-12.5V).
the
pin, all the previously protected sectors are
RESET
During this mode, all formerly protected sectors are
RESET
protected again.
Start
RESET = VID (Note 1)
Perform Erase or
Program Operations
RESET = VIH
Temporary Sector
Unprotect Completed
(Note 2)
Notes:
1. All protected sectors unprotected.
2. All previously protected sectors are protected once again.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 8/46
EFST
F49L004UA / F49L004BA
Figure 16 shows the algorithms and Figure 15 shows
the timing diagram. This method uses standard
microprocessor bus cycle timing. For sector unprotect,
all unprotected sectors must first be protected prior to
the first sector unprotect write cycle.
Output Disable Mode
With the
is at a logic high level (V ), outputs from
IH
OE
the devices are disabled. This will cause the output pins
in a high impedance state
The alternate method intended only for programming
equipment requires V on address pin A9,
, and
OE
ID
Standby Mode
.
RESET
When
and
are both held at V
RESET
± 0.3V,
CE
the device enter CMOS Standby mode. If
CC
CE
are held at V , but not within the range of
and
Auto-select Mode
RESET
± 0.3V, the device will still be in the standby mode,
IH
The auto-select mode provides manufacturer and
device identification and sector protection verification,
through outputs on DQ7–DQ0. This mode is primarily
intended for programming equipment to automatically
V
CC
but the standby current will be larger.
If the device is deselected during auto algorithm of
erasure or programming, the device draws active
match
a
device to be programmed with its
corresponding programming algorithm. However, the
auto-select codes can also be accessed in-system
through the command register.
current I
until the operation is completed. I
in
CC3
CC2
the DC Characteristics table represents the standby
current specification.
When using programming equipment, this mode
requires V (11.5 V to 12.5 V) on address pin A9.
ID
While address pins A3, A2, A1, and A0 must be as
shown in Table 4.
The device requires standard access time (t ) for
CE
read access from either of these standby modes,
before it is ready to read data.
To verify sector protection, all necessary pins have to
be set as required in Table 4, the programming
equipment may then read the corresponding identifier
code on DQ7-DQ0.
Sector Protect / Un-protect Mode
The hardware sector protect feature disables both
program and erase operations in any sector. The
hardware sector unprotect feature re-enables both the
program and erase operations in previously protected
sectors. Sector protect/unprotect can be implemented
via two methods.
To access the auto-select codes in-system, the host
system can issue the auto-select command via the
command register, as shown in Table 5. This method
does not require V . See “ Software Command
ID
Definitions” for details on using the auto-select mode.
The primary method requires V on the
pin
RESET
ID
only, and can be implemented either in-system or via
programming equipment.
7.2 Software Command Definitions
Writing specific address and data commands or
sequences into the command register initiates the
device operations. Table 5 defines the valid register
command sequences. Writing incorrect address and
data values or writing them in the improper sequence
resets the device to reading array data.
All addresses are latched on the falling edge of
WE
, whichever happens later. All data is latched on
or
CE
the rising edge of
or
, whichever happens
WE
CE
first. Refer to the corresponding timing diagrams in
the AC Characteristics section.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
9/46
EFST
F49L004UA / F49L004BA
Table 5. F49L004UA/ F49L004BA Software Command Definitions
1st Bus
Cycle
2nd Bus
Cycle
3rd Bus
Cycle
4th Bus
Cycle
5th Bus
Cycle
6th Bus
Cycle
Bus
Cycles
Command
Addr Data Addr Data Addr Data Addr Data Addr Data Addr Data
Reset (5)
Read (4)
1
1
4
6
6
XXXH F0H
RA RD
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Program
555H AAH 2AAH 55H 555H A0H
PA
PD
Chip Erase
Sector Erase
555H AAH 2AAH 55H 555H 80H 555H AAH 2AAH 55H 555H 10H
555H AAH 2AAH 55H 555H 80H 555H AAH 2AAH 55H
SA
-
30H
-
Sector Erase
Suspend (6)
1
1
XXXH B0H
XXXH 30H
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Sector Erase Resume
(7)
-
-
-
Auto-select
See Table 6.
Notes:
1. X = don’t care
RA = Address of memory location to be read.
RD = Data to be read at location RA.
PA = Address of memory location to be programmed.
PD = Data to be programmed at location PA.
SA = Address of the sector.
2. Except Read command and Auto-select command, all command bus cycles are write operations.
3. Address bits A18–A11 are don’t cares.
4. No command cycles required when reading array data.
5. The Reset command is required to return to reading array data when device is in the auto-select mode, or if
DQ5 goes high(while the device is providing status data).
6. The system may read and program in non-erasing sectors, or enter the auto-select mode, when in the Erase
Suspend mode. The Erase Suspend command is valid only during a sector erase operation.
7. The Erase Resume command is valid only during the Erase Suspend mode.
Table 6. F49L004UA/ F49L004BA Auto-Select Command
1st Bus
Cycle
2nd Bus
Cycle
3rd Bus
Cycle
4th Bus
Cycle
5th Bus
Cycle
6th Bus
Cycle
Bus
Cycles
Command
Addr Data Addr Data Addr Data Addr Data Addr Data Addr Data
4
4
4
4
555H AAH 2AAH 55H 555H 90H X04H 7FH
555H AAH 2AAH 55H 555H 90H X08H 7FH
555H AAH 2AAH 55H 555H 90H X0CH 7FH
555H AAH 2AAH 55H 555H 90H X00H 8CH
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Manufacture ID
Device ID, Upper
boot
Device ID, Bottom
boot
4
4
555H AAH 2AAH 55H 555H 90H X01H B5H
555H AAH 2AAH 55H 555H 90H X01H B6H
-
-
-
-
-
-
-
-
(SA) 00H
555H AAH 2AAH 55H 555H 90H
x02H 01H
Sector Protect Verify
4
-
-
-
-
Notes :
1. The fourth cycle of the auto-select command sequence is a read cycle.
2. For Sector Protect Verify operation: If read out data is 01H, it means the sector has been protected. If read
out data is 00H, it means the sector is still not being protected.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 10/46
EFST
F49L004UA / F49L004BA
Reset Command
Program Command
Writing the reset command to the device resets the
device to reading array data. Address bits are all don’t
cares for this command.
The program command sequence programs one byte
into the device. Programming is a four-bus-cycle
operation. The program command sequence is initiated
by writing two unlock write cycles, followed by the
program set-up command. The program address and
data are written next, which in turn initiate the
Embedded Program algorithm. The system is not
required to provide further controls or timings. The
device automatically provides internally generated
program pulses and verifies the programmed cell
margin.
The reset command may be written between the
sequence cycles in an erase command sequence
before erasing begins. This resets the device to reading
array data. Once erasure begins, however, the device
ignores reset commands until the operation is
complete.
The reset command may be written between the
sequence cycles in a program command sequence
before programming begins. This resets the device to
reading array data (also applies to programming in
Erase Suspend mode). Once programming begins,
however, the device ignores reset commands until the
operation is complete.
When the Embedded Program algorithm is complete,
the device then returns to reading array data and
addresses are no longer latched. The system can
determine the status of the program operation by using
DQ7, DQ6, or RY/
. See “Write Operation Status”
BY
section for more information on these status bits.
The reset command may be written between the
sequence cycles in an auto-select command sequence.
Once in the auto-select mode, the reset command must
be written to return to reading array data (also applies
to auto-select during Erase Suspend).
Any commands written to the device during the
Embedded Program Algorithm are ignored. Note that a
hardware
reset
immediately
terminates
the
programming operation. The Program command
sequence should be reinitiated once the device has
reset to reading array data, to ensure data integrity.
If DQ5 goes high(see “DQ5: Exceeded Timing Limits”
section) during a program or erase operation, writing
the reset command returns the device to reading array
data (also applies during Erase Suspend).
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed from a
“0” back to a “1”. Attempting to do so may halt the
operation and set DQ5 to “1”, or cause the Data Polling
algorithm to indicate the operation was successful.
However, a succeeding read will show that the data is
still “0”. Only erase operations can convert a “0” to a
“1”.
Read Command
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is also ready to read array
data after completing an Embedded Program or
Embedded Erase algorithm.
Chip Erase Command
Chip erase is a six-bus cycle operation. The chip erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase
algorithm.
When the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The
system can read array data using the standard read
timings, except that if it reads an address within
erase-suspended sectors, the device outputs status
data. After completing a programming operation in the
Erase Suspend mode, the system may once again read
array data with the same exception. See “Erase
Suspend/Erase Resume Commands” for more
information on this mode.
The device does not require the system to preprogram
prior to erase. The Embedded Erase algorithm
automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical
erase.
The system must issue the reset command to
re-enable the device for reading array data if DQ5 goes
high, or while in the auto-select mode. See the “Reset
Command” section. See also the “Read Mode” in the
“Device Operations” section for more information. Refer
to Figure 5 for the timing diagram.
Any commands written to the chip during the
Embedded Erase algorithm are ignored. Note that a
hardware reset during the chip erase operation
immediately terminates the operation. The Chip Erase
command sequence should be reinitiated once the
device has returned to reading array data, to ensure
the data integrity.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
11/46
EFST
F49L004UA / F49L004BA
The system can determine the status of the erase
operation. The Sector Erase command sequence
should be reinitiated once the device has returned to
reading array data, to ensure the data integrity.
operation by using DQ7, DQ6, DQ2, or RY/
. See
BY
“Write Operation Status” section for more information
on these status bits.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are
no longer latched. The system can determine the
status of the erase operation by using DQ7, DQ6,
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses are
no longer latched. See the Erase/Program Operations
tables in “AC Characteristics” for parameters.
DQ2, or RY/
. (Refer to “Write Operation Status”
BY
section for more information on these status bits.)
Refer to the Erase/Program Operations tables in the
“AC Characteristics” section for parameters.
Sector Erase Command
Sector erase is a six-bus cycle operation. The sector
erase command sequence is initiated by writing two
unlock cycles, followed by a set-up command. Two
additional unlock write cycles are then followed by the
address of the sector to be erased, and the sector
erase command.
Sector Erase Suspend/Resume Command
The Erase Suspend command allows the system to
interrupt a sector erase operation and then read data
from, or program data to, any sector not selected for
erasure (The device “erase suspends” all sectors
selected for erasure.). This command is valid only
during the sector erase operation, including the 50 µs
time-out period during the sector erase command
sequence. The Erase Suspend command is ignored if
written during the chip erase operation or Embedded
Program algorithm. Addresses are “don’t-cares” when
writing the Erase Suspend command as shown in
Table 5.
The device does not require the system to preprogram
the memory prior to erase. The Embedded Erase
algorithm
automatically programs and verifies the sector for an all
zero data pattern prior to electrical erase. The system is
not required to provide any controls or timings during
these operations.
After the command sequence is written, a sector erase
time-out of 50 µs begins. During the time-out period,
additional sector addresses and sector erase
commands may be written. Loading the sector erase
buffer may be done in any sequence, and the number
of sectors may be from one sector to all sectors. The
time between these additional cycles must be less than
50 μs, otherwise the last address and command might
not be accepted, and erasure may begin.
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum
of 20 µs to suspend the erase operation. However,
when the Erase Suspend command is written during
the sector erase time-out, the device immediately
terminates the time-out period and suspends the erase
operation.
Reading at any address within erase-suspended
sectors produces status data on DQ7–DQ0. The
system can use DQ7, or DQ6 and DQ2 together, to
It is recommended that processor interrupts be disabled
during this time to ensure all commands are accepted.
The interrupts can be re-enabled after the last Sector
Erase command is written. If the time between
additional sector erase commands can be assumed to
be less than 50 µs, the system need not monitor DQ3.
determine if
a sector is actively erasing or is
erase-suspended. See “Write Operation Status”
section for more information on these status bits.
After an erase-suspended program operation is
complete, the system can once again read array data
within non-suspended sectors. The system can
determine the status of the program operation using
the DQ7 or DQ6 status bits, just as in the standard
program operation. See “Write Operation Status” for
more information.
Any command other than Sector Erase or Erase
Suspend during the time-out period resets the device to
reading array data. The system must rewrite the
command sequence and any additional sector
addresses and commands.
The system can monitor DQ3 to determine if the sector
erase timer has timed out. (See the “DQ3: Sector Erase
Timer” section.) The time-out begins from the rising
The system may also write the auto-select command
sequence when the device is in the Erase Suspend
mode. The device allows reading auto-select codes
even at addresses within erasing sectors, since the
codes are not stored in the memory array. When the
device exits the auto-select mode, the device reverts to
the Erase Suspend mode, and is ready for another
valid operation.
edge of the final WE pulse in the command
sequence.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands
are ignored. Note that a hardware reset during the
sector erase operation immediately terminates the
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
12/46
EFST
F49L004UA / F49L004BA
The system must write the Erase Resume command
(address bits are “don’t care” as shown in Table 5) to
exit the erase suspend mode and continue the sector
erase operation. Further writes of the Resume
command are ignored. Another Erase Suspend
command can be written after the device has resumed
erasing.
The auto-select command sequence is initiated by
writing two unlock cycles, followed by the auto-select
command. The device then enters the auto-select
mode, and the system may read at any address any
number of times, without initiating another command
sequence. The read cycles at address 04H, 08H, 0CH,
and 00H retrieves the EFST manufacturer ID. A read
cycle at address 01H retrieves the device ID. A read
cycle containing a sector address (SA) and the
address 02H returns 01H if that sector is protected, or
00H if it is unprotected. Refer to Tables 1 and 2 for
valid sector addresses.
Auto-select Command
The auto-select command sequence allows the host
system to access the manufacturer and devices codes,
and determine whether or not a sector is protected.
Table 6 shows the address and data requirements. This
method is an alternative to that shown in Table 4, which
The system must write the reset command to exit the
auto-select mode and return to reading array data.
is intended for PROM programmers and requires V
on address bit A9.
ID
7.3 Write Operation Status
The device provides several bits to determine the
status of a write operation: RY/ , DQ7, DQ6,
DQ5, DQ3, DQ2, and. Table 7 and the following
subsections describe the functions of these bits.
RY/ , DQ7, and DQ6 each offer a method for
BY
determining whether a program or erase operation
is complete or in progress.
BY
Table 7. Write Operation Status
DQ7
DQ5
(Note2)
Status
DQ6
DQ3 DQ2
RY/
BY
(Note1)
No
N/A
Embedded Program Algorithm
Embedded Erase Algorithm
Toggle
Toggle
0
0
0
0
DQ7
0
Toggle
1
Toggle
0
1
Reading Erase Suspended
Sector
No
Toggle
In Progress
1
N/A Toggle
Reading Non-Erase
Suspended Sector
Erase Suspended Mode
Data
DQ7
DQ7
Data
Data Data Data
1
0
0
Erase Suspend Program
Toggle
Toggle
0
1
N/A
N/A
N/A
No
Toggle
Embedded Program Algorithm
Exceeded
Time Limits
Embedded Erase Algorithm
Erase Suspend Program
0
Toggle
Toggle
1
1
1
Toggle
N/A
0
0
N/A
DQ7
Notes:
1. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection
for further details.
2. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the
maximum timing limits. See “DQ5: Exceeded Timing Limits” for more information.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 13/46
EFST
F49L004UA / F49L004BA
Output Enable (
) is asserted low. Refer to Figure
OE
RY/BY :
21, Data Polling Timings (During Embedded
Algorithms), Figure 19 shows the Data Polling
algorithm.
Ready/Busy (for 40-pin TSOP package)
The RY/
is a dedicated, open-drain output pin that
BY
indicates whether an Embedded Algorithm is in
progress or complete. The RY/ status is valid after
DQ6:Toggle BIT I
BY
pulse in the command
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete,
or whether the device has entered the Erase Suspend
mode. Toggle Bit I may be read at any address, and is
the rising edge of the final
sequence. Since RY/
several RY/
BY
with a pull-up resistor to V
WE
is an open-drain output,
BY
pins can be tied together in parallel
.
CC
valid after the rising edge of the final
pulse in the
WE
command sequence (prior to the program or erase
operation), and during the sector erase time-out.
If the output is low (Busy), the device is actively erasing
or programming. (This includes programming in the
Erase Suspend mode.) If the output is high (Ready),
the device is ready to read array data (including during
the Erase Suspend mode), or is in the standby mode.
During an Embedded Program or Erase algorithm
operation, successive read cycles to any address
cause DQ6 to toggle. The system may use either
OE
to control the read cycles. When the operation
Table 7 shows the outputs for RY/
.
BY
or
CE
is complete, DQ6 stops toggling.
DQ7: Data Polling
When an erase command sequence is written, if all
sectors selected for erasing are protected, DQ6
toggles for approximately 100 µs, then returns to
reading array data. If not all selected sectors are
protected, the Embedded Erase algorithm erases the
unprotected sectors, and ignores the selected sectors
that are protected.
The DQ7 indicates to the host system whether an
Embedded Algorithm is in progress or completed, or
whether the device is in Erase Suspend mode. The
Data Polling is valid after the rising edge of the final
pulse in the program or erase command
WE
sequence.
The system can use DQ6 and DQ2 together to
determine whether a sector is actively erasing or is
erase-suspended. When the device is actively erasing
(i.e. the Embedded Erase algorithm is in progress),
DQ6 toggles. When the device enters the Erase
Suspend mode, DQ6 stops toggling. However, the
system must also use DQ2 to determine which sectors
are erasing or erase-suspended. Alternatively, the
system can use DQ7.
During the Embedded Program algorithm, the device
outputs on DQ7 the complement of the datum
programmed
to DQ7. This DQ7 status also applies to programming
during Erase Suspend. When the Embedded Program
algorithm is complete, the device outputs the true data
on DQ7. The system must provide the program address
to read valid status information on DQ7. If a program
address falls within a protected sector, Data Polling on
DQ7 is active for approximately 1 µs, then the device
returns to reading array data.
If a program address falls within a protected sector,
DQ6 toggles for approximately 2 µs after the program
command sequence is written, then returns to reading
array data.
During the Embedded Erase algorithm, Data Polling
produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the device enters the Erase
Suspend mode, Data Polling produces a “1” on DQ7.
The system must provide an address within any of the
sectors selected for erasure to read valid status
information on DQ7.
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded
Program algorithm is complete. Table 7 shows the
outputs for Toggle Bit I on DQ6. Figure 20 shows the
toggle bit algorithm. Figure 22 shows the toggle bit
timing diagrams. Figure 25 shows the differences
between DQ2 and DQ6 in graphical form. Refer to the
subsection on DQ2: Toggle Bit II.
After an erase command sequence is written, if all
sectors selected for erasing are protected, Data Polling
on DQ7 is active for approximately 100 µs, then the
device returns to reading array data. If not all selected
sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the
selected sectors that are protected.
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6,
indicates whether a particular sector is actively erasing
(that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit II
When the system detects DQ7 has changed from the
complement to true data, it can read valid data at DQ7~
DQ0 on the following read cycles. This is because DQ7
may change asynchronously with DQ0–DQ6 while
is valid after the rising edge of the final WE or CE ,
whichever happens first, in the command sequence.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
14/46
EFST
F49L004UA / F49L004BA
DQ2 toggles when the system reads at addresses
within those sectors that have been selected for
exceeded the specified limits(internal pulse count).
Under these conditions DQ5 will produce a "1". This
time-out condition indicates that the program or erase
cycle was not successfully completed. Data Polling and
Toggle Bit are the only operating functions of the
device under this condition.
erasure. (The system may use either
or
to
CE
OE
control the read cycles.) But DQ2 cannot distinguish
whether the sector is actively erasing or is
erase-suspended.
If this time-out condition occurs during sector erase
operation, it specifies that a particular sector is bad and
it may not be reused. However, other sectors are still
functional and may be used for the program or erase
operation. The device must be reset to use other
sectors. Write the Reset command sequence to the
device, and then execute program or erase command
sequence. This allows the system to continue to use
the other active sectors in the device.
DQ6, by comparison, indicates whether the device is
actively erasing, or whether is in erase-suspended, but
cannot distinguish which sectors are selected for
erasure. Thus, both status bits are required for sector
and mode information. Refer to Table 7 to compare
outputs for DQ2 and DQ6.
Figure 20 shows the toggle bit algorithm in flowchart
form. See also the DQ6: Toggle Bit I subsection. Figure
22 shows the toggle bit timing diagram. Figure 25
shows the differences between DQ2 and DQ6 in
graphical form.
If this time-out condition occurs during the chip erase
operation, it specifies that the entire chip is bad or
combination
of sectors are bad.
If this time-out condition occurs during the
programming operation, it specifies that the sector
containing that byte is bad and this sector may not be
reused, however other sectors are still functional and
can be reused.
Reading Toggle Bits DQ6/ DQ2
Refer to Figure 20 for the following discussion.
Whenever the system initially begins reading toggle bit
status, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the
system would note and store the value of the toggle bit
after the first read. After the second read, the system
would compare the new value of the toggle bit with the
first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The system
can read array data on DQ7–DQ0 on the following read
cycle.
The time-out condition will not appear if a user tries to
program a non blank location without erasing. Please
note that this is not a device failure condition since the
device was incorrectly used.
DQ3:Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If
additional sectors are selected for erasure, the entire
timeout also applies after each additional sector erase
command.
When the time-out is complete, DQ3 switches from “0”
to “1.” If the time between additional sector erase
commands from the system can be assumed to be less
than 50 µs, the system need not monitor DQ3.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the
system should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should
then determine again whether the toggle bit is toggling,
since the toggle bit may have stopped toggling just as
DQ5 went high. If the toggle bit is no longer toggling,
the device has successfully completed the program or
erase operation. If it is still toggling, the device did not
completed the operation successfully, and the system
must write the reset command to return to reading
array data.
When the sector erase command sequence is written,
the system should read the status on DQ7 (Data
Polling) or DQ6 (Toggle Bit I) to ensure the device has
accepted the command sequence, and then read DQ3.
If DQ3 is “1”, the internally controlled erase cycle has
begun; all further commands (except Erase Suspend)
are ignored until the erase operation is complete.
The remaining scenario is that the system initially
determines that the toggle bit is toggling and DQ5 has
not gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles,
determining the status as described earlier.
Alternatively, it may choose to perform other system
tasks. In this case, the system must start at the
beginning of the algorithm when it returns to determine
the status of the operation.
If DQ3 is “0”, the device will accept additional sector
erase commands. To ensure the command has been
accepted, the system software should check the status
of DQ3 prior to and following each subsequent sector
erase command. If DQ3 is high on the second status
check, the last command might not have been
accepted. Table 7 shows the outputs for DQ3.
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
15/46
EFST
F49L004UA / F49L004BA
7.4 More Device Operations
Hardware Data Protection
Write cycles are inhibited by holding any one of
=
OE
V ,
IL
= V or
= V . To initiate a write cycle,
WE
CE
and
IH
IH
The command sequence requirement of unlock cycles for
programming or erasing provides data protection against
inadvertent writes. In addition, the following hardware
data protection measures prevent accidental erasure or
programming, which might otherwise be caused by
must be a logical zero while
is a
OE
WE
CE
logical one.
Power Supply Decoupling
spurious system level signals during V
power-up and
CC
power-down transitions, or from system noise.
In order to reduce power switching effect, each device
should have a 0.1uF ceramic capacitor connected
between
Low VCC Write Inhibit
its V
CC
and GND.
When V
is less than VLKO, the device does not accept
any write cycles. This protects data during V power-up
CC
CC
Power-Up Sequence
and power-down. The command register and all internal
program/erase circuits are disabled, and the device
The device powers up in the Read Mode. In addition, the
memory contents may only be altered after successful
completion of the predefined command sequences.
resets. Subsequent writes are ignored until V
is
CC
greater than V
. The system must provide the proper
LKO
signals to the control pins to prevent unintentional writes
when V
is greater than V
CC LKO
.
Power-Up Write Inhibit
If
=
= V and
= V during power up, the
OE
IH
WE
device does not accept commands on the rising edge of
. The internal state machine is automatically reset to
CE
IL
Write Pulse "Glitch" Protection
WE
reading array data on power-up.
Noise pulses of less than 5 ns (typical) on
,
or
OE CE
do not initiate a write cycle.
WE
Logical Inhibit
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 16/46
EFST
F49L004UA / F49L004BA
8. ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . . –65°C to +150°C
Ambient Temperature
with Power Applied. . . . . . . .. . . . . . –65°C to +125°C
Voltage with Respect to Ground
2. Minimum DC input voltage on pins A9,
,
OE
is -0.5 V. During voltage
transitions, A9, and may
and
RESET
,
OE
RESET
overshoot V to –2.0 V for periods of up to 20
SS
ns. See Figure 1. Maximum DC input voltage
on pin A9 is +12.5 V which may overshoot to
14.0 V for periods up to 20 ns.
VCC (Note 1) . . . . . . . . . . .–0.5 V to +4.0 V
A9,
,
OE
and
(Note 2) …. . . .. . . . . –0.5 V to +12.5 V
RESET
3. No more than one output may be shorted to
ground at a time. Duration of the short circuit
should not be greater than one second.
All other pins (Note 1). . . . . . . . . . –0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) .. . .. 200 mA
Notes:
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is
a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating
conditions for extended periods may affect device
reliability.
1. Minimum DC voltage on input or I/O pins
is –0.5 V. During voltage transitions, input or
I/O pins may overshoot V to
SS
–2.0 V for periods of up to 20 ns. See Figure 1.
Maximum DC voltage on input or I/O pins is
V
CC
+0.5 V. During voltage transitions, input or
I/O pins may overshoot to V
CC
periods up to 20 ns. See Figure 2.
+2.0 V for
Figure 1. Maximum Negative Overshoot Waveform
20ns
20ns
+0 . 8 V
- 0. 5V
- 2. 0V
20ns
Figure 2. Maximum Positive Overshoot Waveform
20ns
Vc c
+ 2 . 0 V
Vc c
+ 0 . 5 V
2. 0V
20ns
20ns
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 17/46
EFST
F49L004UA / F49L004BA
OPERATING RANGES
Commercial (C) Devices Ambient Temperature (TA) . . . . . . . . . . . 0°C to +70°C
VCC Supply Voltages VCC for all devices . . . . . . . . . . . . . . . . . . . . .2.7 V to 3.6 V
Operating ranges define those limits between which the functionality of the device is guaranteed.
Table 8. Capacitance TA = 25°C , f = 1.0 MHz
Symbol
CIN1
Description
Conditions
VIN = 0V
Min.
Typ.
Max.
8
Unit
pF
Input Capacitance
CIN2
Control Pin
VIN = 0V
12
pF
Capacitance
COUT
Output Capacitance
VOUT = 0V
12
pF
9. DC CHARACTERISTICS
Table 9. DC Characteristics TA = 0C to 70C, VCC = 2.7V to 3.6V
Symbol
ILI
Description
Conditions
Min.
Typ.
Max.
±1
Unit
uA
Input Leakage Current
A9 Input Leakage Current
Output Leakage Current
VIN = VSS or VCC, VCC = VCC max.
VCC = VCC max; A9=12.5V
ILIT
35
uA
ILO
VOUT = VSS or VCC, VCC = VCC max
±1
uA
@5MHz
@1MHz
7
2
12±
4±
mA
mA
mA
uA
= VIL,
= VIH
CE
ICC1
VCC Active Read Current
OE
ICC2
ICC3
VCC Active write Current
VCC Standby Current
15
0.2
30±
5
= VIL,
= VIH
CE
OE
;
= VCC ±±0.3V
CE RESET
VCC Standby Current
During Reset
ICC4
= VSS ±±0.3V
0.2
0.2
5
uA
RESET
ICC5
VIL
Automatic sleep mode
Input Low Voltage(Note 1)
Input High Voltage
VIH = VCC ±±0.3V; VIL = VSS ±±0.3V
5
uA
V
-0.5
0.8
VIH
0.7x VCC
VCC + 0.3
V
Voltage for Auto-Select
and Temporary Sector
Unprotect
VID
V
CC =3.3V
11.5
12.5
0.45
V
V
VOL
VOH1
VOH2
VLKO
Output Low Voltage
Output High Voltage(TTL)
Output High Voltage
IOL = 4.0mA, VCC = VCC min
IOH = -2mA, VCC = VCC min
IOH = -100uA, VCC min
0.85x VCC
VCC -0.4
2.3
Low VCC Lock-out Voltage
2.5
V
Notes :
1. VIL min. = -1.0V for pulse width is equal to or less than 50 ns.
VIL min. = -2.0V for pulse width is equal to or less than 20 ns.
2. VIH max. = VCC + 1.5V for pulse width is equal to or less than 20 ns
If VIH is over the specified maximum value, read operation cannot be guaranteed.
3. Automatic sleep mode enable the low power mode when addresses remain stable for 250 ns
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 18/46
EFST
F49L004UA / F49L004BA
10. AC CHARACTERISTICS
TEST CONDITIONS
Figure 3. Test Setup
2.7K
Ω
DEVICE UNDER
TEST
+3.3V
DIODES = IN3064
OR EQUIVALENT
CL
6.2KΩ
CL = 100pF Including jig capacitance
CL = 30pF for F49L004U(B)A
Figure 4. Input Waveforms and Measurement Levels
3. 0V
0V
1. 5V
1. 5V
Test Poin t s
Inpu t
Out pu t
A C TE S TIN G
In p ut p ul s e r i s e a nd f a l l ti m e s a re
:
In p u t s a r e d ri v e n a t 3 . 0 V f o r
5 n s .
a
l o g i c " 1 " a n d 0 V f o r
a
l o g i c " 0 "
<
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 19/46
EFST
F49L004UA / F49L004BA
10.1 Read Operation
TA = 0C to 70C, VCC = 2.7V~3.6V
Table 10. Read Operations
-70
-90
Symbol
Description
Conditions
Unit
Min.
Max.
Min.
Max.
tRC
Read Cycle Time (Note 1)
Address to Output Delay
70
90
ns
ns
tACC
70
70
30
90
90
35
=
= VIL
CE OE
to Output Delay
CE
tCE
tOE
ns
ns
= VIL
OE
CE
= VIL
= VIL
to Output Delay
OE
High to Output Float
(Note1)
OE
tDF
25
30
ns
ns
ns
ns
CE
tOEH
Output Enable
Read
0
10
0
0
10
0
Toggle and
Data Polling
Hold Time
tOH
Address to Output hold
=
= VIL
CE OE
Notes :
1. Not 100% tested.
2. tDF is defined as the time at which the output achieves the open circuit condition and data is no longer
driven.
Figure 5. Read Timing Waveform
tR C
Addresses Stabl e
tA C C
Addr es s
C E
tD F
t O E
OE
tO E H
W E
tC E
tO H
H i gh - Z
H i gh - Z
Output Vali d
Outputs
RE S E T
RY/B Y
0V
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 20/46
EFST
F49L004UA / F49L004BA
10.2 Program/Erase Operation
Table 11.
Symbol
Controlled Program/Erase Operations(TA = 0C to 70C, VCC = 2.7V~3.6V)
WE
-70
-90
Description
Unit
Min.
70
Max.
Min.
90
Max.
Write Cycle Time (Note 1)
Address Setup Time
Address Hold Time
Data Setup Time
ns
ns
ns
ns
ns
ns
t
WC
0
45
35
0
0
45
35
0
t
AS
AH
DS
DH
t
t
Data Hold Time
t
Output Enable Setup Time
Read Recovery Time Before
0
0
t
OES
0
0
ns
t
GHWL
Write (
High to
low)
WE
OE
Setup Time
Hold Time
0
0
0
0
ns
ns
ns
ns
CE
CE
t
CS
t
CH
Write Pulse Width
Write Pulse Width High
35
30
35
30
t
WP
t
WPH
Programming Operation (Note 2)
(Byte program time)
9(typ.)
9(typ.)
us
t
t
WHWH1
WHWH2
Sector Erase Operation (Note 2)
0.7(typ.)
0.7(typ.)
sec
us
50
0
50
0
t
V
CC
Setup Time (Note 1)
VCS
ns
Recovery Time from RY/
t
BY
RB
90
90
ns
Program/Erase Valid to RY/
Delay
BY
t
busy
Notes :
1. Not 100% tested.
2. See the "Erase and Programming Performance" section for more information.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 21/46
EFST
F49L004UA / F49L004BA
Table 12.
Controlled Program/Erase Operations(TA = 0C to 70C, VCC = 2.7V~3.6V)
CE
-70
-90
Symbol
Description
Min.
Max.
Min.
Max.
Unit
Write Cycle Time (Note 1)
Address Setup Time
Address Hold Time
Data Setup Time
70
90
ns
t
WC
0
45
35
0
0
45
35
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
us
sec
t
AS
AH
DS
DH
t
t
Data Hold Time
t
Output Enable Setup Time
0
0
t
OES
Read Recovery Time Before Write
0
0
t
GHEL
0
0
Setup Time
Hold Time
t
WE
WE
CE
WS
0
0
t
WH
Pulse Width
35
30
35
30
t
CP
Pulse Width High
CE
t
CPH
Programming Operation(note2)
Sector Erase Operation (note2)
9(typ.)
9(typ.)
t
t
WHWH1
WHWH2
0.7(typ.)
0.7(typ.)
Notes :
1. Not 100% tested.
2. See the "Erase and Programming Performance" section for more information.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 22/46
EFST
F49L004UA / F49L004BA
Figure 6. Write Command Timing Waveform
V C C
3V
V I H
V I L
Addr es s
AD D V al i d
tA H
t A S
V I H
V I L
W E
t O E S
t W P
tW P H
tC W C
V I H
V I L
C E
OE
tC S
tC H
V I H
V I L
tD H
tD H
V I H
V I L
D I N
Dat a
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 23/46
EFST
F49L004UA / F49L004BA
Figure 7. Embedded Programming Timing Waveform
5 5 5 f o r p r o g r a m P A f o r p r o g r a m
2 A A f o r e r a s e
S A f o r s e c t o r e r a s e
5 5 5 f o r c h i p e r a s e
Data P ol li n g
P D
Addr es s
tW C
tW H
t A S
tA H
W E
OE
tG H E L
tC P
tW H W H 1 o r
2
C E
t W S
tD S
tC P H
tD H
tB U S Y
Dat a
D O U T
DQ7
P D f o r p r o g r a m
3 0 f o r s e c t o r e r a s e
1 0 f o r c h i p e r a s e
A0 f o r p r o g r a m
5 5 f o r e r a s e
tR H
RE S E T
RY/B Y
Notes :
1. PA = Program Address, PD = Program Data, DOUT = Data Out , DQ7 = complement of data written to device
2. Figure indicates the last two bus cycles of the command sequence..
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 24/46
EFST
F49L004UA / F49L004BA
Figure 8. Embedded Programming Algorithm Flowchart
Start
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data A0H Address 555H
Data Poll
from system
Increment
address
No
Verify Work OK?
Yes
No
Last address?
Yes
Embedded Program Completed
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 25/46
EFST
F49L004UA / F49L004BA
Figure 9. CE Controlled Program Timing Waveform
5 5 5 f o r p r o g r a mP A f o r p r o g r a m
2 A A f o r e r a s e S A f o r s e c t o r e r a s e
5 5 5 f o r c h i p e r a s e
Data P ol li n g
P D
Addr es s
tW C
tW H
t A S
tA H
W E
tG H E L
OE
tC P
tW H W H 1 o r
2
C E
tC P H
tD H
t W S
tB U S Y
tD S
Dat a
D O U T
DQ7
P D f o r p r o g r a m
3 0 f o r s e c t o r e r a s e
1 0 f o r c h i p e r a s e
A0 f o r p r o g r a m
5 5 f o r e r a s e
tR H
RE S E T
RY/B Y
Notes :
1. PA = Program Address, PD = Program Data, DOUT = Data Out , DQ7 = complement of data written to device
2. Figure indicates the last two bus cycles of the command sequence..
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 26/46
EFST
F49L004UA / F49L004BA
Figure 10. Embedded Chip Erase Timing Waveform
Read Statu s Dat a
Er as e Com mand S equ en ce( last t w o cycl e)
t A S
tW C
2AAAh
VA
VA
Addr es s
555h
tA H
C E
tC H
tG H W L
OE
tW H W H 1
t W P
W E
tW P H
tC S
tD S
tD H
I n
P r o g r e s s
C o m p l e t e
10h
55h
Dat a
tB U S Y
tR B
RY/B Y
tV C S
V C C
Notes :
SA = Sector Address (for Sector Erase, VA = Valid Address for reading status data
(see "Write Operation Status")
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 27/46
EFST
F49L004UA / F49L004BA
Figure 11. Embedded Chip Erase Algorithm Flowchart
Start
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 10H Address 555H
Data Poll from System
No
Data = FFh?
Yes
Embedded Chip Erease Completed
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 28/46
EFST
F49L004UA / F49L004BA
Figure 12. Embedded Sector Erase Timing Waveform
Read Statu s Dat a
Er as e Com m and S equ en ce( last t w o cycl e)
t A S
tW C
2AAAh
VA
VA
SA
Addr es s
tA H
C E
tC H
tG H W L
OE
tW H W H 1
t W P
W E
tW P H
tC S
tD S
tD H
I n
P r o g r e s s
C o m p l e t e
30h
55h
Dat a
tB U S Y
tR B
RY/ B
Y
tV C S
V C C
Notes :
SA = Sector Address (for Sector Erase, VA = Valid Address for reading status data
(see "Write Operation Status")
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 29/46
EFST
F49L004UA / F49L004BA
Figure 13. Embedded Sector Erase Algorithm Flowchart
Start
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 30H Address SA
No
Last Sector
to Erase
Yes
Data Poll from System
No
Data = FFh?
Embedded Sector Erease Completed
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 30/46
EFST
F49L004UA / F49L004BA
Figure 14. Erase Suspend/Erase Resume Flowchart
Start
Write Data B0H
ERASE SUSPEND
No
Toggle Bit checking Q6
not toggled
Yes
Read Array or
Program
No
Reading or
Programming End
Yes
Write Data 30H
ERASE RESUME
Continue Erase
No
Another
Erase Suspend?
Yes
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
31/46
EFST
F49L004UA / F49L004BA
Figure 15. In-System Sector Protect/Unprotect Timing Waveform (
Control)
RESET
RE S E T
SA,A6
A1,A0
Val i d*
Val i d*
Val i d*
Status
Sec tor P rotec t Sec tor U npr ot ec t
Ver i f y
40h
60h
60h
Dat a
S e c t o r P r o t e c t
=
1 5 0 u s
1 5 m s
S e c t o r U n p r o t e c t
=
t W P
C E
W E
OE
Notes :
When sector protect, A6=0, A1=1.
When sector unprotect, A6=1, A1=1, A0=0.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 32/46
EFST
F49L004UA / F49L004BA
Figure 16. In-System Sector Protect/Unprotect Algorithm (
= VID)
RESET
Start
Start
PLSCNT = 1
PLSCNT = 1
Protect all sector :
The indicated portion
of the sector protect
algorithm must be
performed for all
unprotected sectors
prior to issuing the
first sector
RESET = VID
RESET = VID
μ
Wait 1 s?
μ
Wait 1 s?
unprotect address
No
First W rite
No
Temporary Sector
Unprotect Mode
First W rite
Temporary Sector
Unprotect Mode
Cycle
=
60h?
Cycle
=
60h?
Yes
Yes
Set up sector
address
No
All sectors
protected?
Yes
Set up first
Sector Protect :
Write 60h to sector
address with
A6 = 0, A1 = 1,
A0 = 0
sector address
Sector Unprotect :
Write 60h to sector
address with
Wait 150μ s?
A6 = 1, A1 = 1,
A0 = 0
Verify Sector
Protect : Write 40h
to sector address
with A6 = 0,
Reset
PLSCNT = 1
Wait 15 ms?
Increment
PLSCNT
A1 = 1, A0 = 0
Verify Sector
Unprotect : Write
40h to sector
address with
A6 = 1, A1 = 1,
A0 =0
Read from
sector address
with A6 = 0,
Increment
PLSCNT
A1 = 1, A0 = 0
No
No
Data = 01h?
Yes
PLSCNT = 25?
Read from
sector address
with A6 = 1,
Yes
A1 = 1, A0 =0
Device failed
Yes
Protect another
sector?
No
Set up
next sector
address
No
No
PLSCNT
= 1000?
Data = 00h?
Yes
Remove VID
from RESET
Yes
Device failed
No
Last sector
verified?
Write reset
command
Yes
Sector Protect
complete
Sector Protect
Algorithm
Remove VID
from RESET
Sector Unprotect
Algorithm
Write reset
command
Sector Protect
complete
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 33/46
EFST
F49L004UA / F49L004BA
Figure 17. Sector Protect Timing Waveform (A9,
Control)
OE
A0,A1
A6
12V
3V
A9
t V L H T
12V
3V
Ver i f y
OE
t V L H T
t V L H T
tW P P 1
W E
C E
t O E S P
01H
F 0 H
Dat a
t O E
Sec tor Addr es s
A18~A12
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 34/46
EFST
F49L004UA / F49L004BA
Figure 18. Sector Protection Algorithm (A9,
Control)
OE
Start
Set up sector address
PLSCNT = 1
OE = VID, A9 = VID, CE = VIL
A6 = VIL
Activate WE Pluse
Time out 150us
Set WE = VIH , CE = OE = VIL
A9 should remain VID
Read from Sector
Address = SA, A0 = 1, A1 = 1
No
No
Data = 01H?
PLSCNT = 32?
Yes
Device Failed
Yes
Protect Another
Sector?
Remove VID from A9
Write reset command
Sector Protection
Complete
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 35/46
EFST
F49L004UA / F49L004BA
WRITE OPERATION STATUS
Figure 19. Data Polling Algorithm
Start
Read Q7~Q0
Add. = VA(1)
Yes
Q7 = Data?
No
No
Q5 = 1?
Yes
Read Q7~Q0
Add. = VA
Yes
Q7 = Data?
(2)
No
Pass
FAIL
Notes :
1. VA =Valid address for programming.
2. Q7 should be re-checked even Q5 = "1" because
Q7 may change simultaneously with Q5.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
36/46
EFST
F49L004UA / F49L004BA
Figure 20. Toggle Bit Algorithm
Start
Read Q7 ~ Q0
Read Q7 ~ Q0
(Note 1)
No
Toggle Bit = Q6
Toggle?
Yes
No
Q5 = 1?
Yes
(Note 1,2)
Read Q7~Q0 Twice
No
Toggle bit Q6
=
Toggle?
Yes
Program / Erase operation
Not complete, write
reset command
Program / Erase
operation complete
Note :
1. Read toggle bit twice to determine whether or not it is toggle.
2. Recheck toggle bit because it may stop toggling as Q5 change to "1".
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
37/46
EFST
F49L004UA / F49L004BA
Figure 21. Data Polling Timings (During Embedded Algorithms)
tR C
VA
Addr es s
VA
tA C C
tC E
C E
tC H
t O E
OE
tO E H
tD F
W E
tO H
H i gh - Z
H i gh - Z
C o m p l e m e n t
V a i l d D a t a
C o m p l e m e n t
T r u e
T r u e
DQ7
S t a t u s D a t a
Va i l d D a t a
S t a t u s D a t a
DQ 0~ DQ 6
tB U S Y
RY/B Y
Notes :
VA = Valid Address. Figure shows first status cycle after command sequence, last status read cycle, and array
data read cycle.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 38/46
EFST
F49L004UA / F49L004BA
Figure 22. Toggle Bit Timing Waveforms (During Embedded Algorithms)
tR C
VA
tAC C
tC E
VA
Addr es s
VA
VA
C E
tC H
t O E
OE
W E
tO E H
tD F
tO H
H i gh - Z
V
a
i
l d
S t a t u s
V a
i
l d
S t a t u s
V a
i l d D a t a
V a
i l d D a t a
DQ6/DQ 2
( s e c o n d r e a d )
( f i r s t r e a d )
( s t o p s t o g g l i n g )
tB U S Y
RY/B Y
Notes :
VA = Valid Address; not required for DQ6. Figure shows first status cycle after command sequence, last status
read cycle, and array data read cycle.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 39/46
EFST
F49L004UA / F49L004BA
10.3 Hardware Reset Operation
Table 13. AC CHARACTERISTICS (for 40-pin TSOP package type)
Symbol
Description
All Speed Options
Unit
Pin Low (During Embedded Algorithms)
to Read or Write (See Note)
RESET
T
READY1
READY2
Max
Max
Min
20
us
Pin Low (NOT During Embedded
Algorithms) to Read or Write (See Note)
RESET
T
500
500
ns
ns
Pulse Width (During Embedded
RESET
Algorithms)
T
RP
High Time Before Read(See Note)
RESET
Min
Min
50
0
ns
ns
T
T
RH
RY/
BY
Recovery Time(to
,
go low)
CE OE
RB
Notes :
Not 100% tested
Figure 23.
Timing Waveform (for 40-pin TSOP package type)
RESET
RY/B Y
CE, O E
RE S E T
tR H
tR P
tR e a d y 2
Reset T i mi ng NO T dur i ng Au tom at i c Al gor i th m s
tR e a d y 1
RY/B Y
tR B
CE, O E
RE S E T
tR P
Reset T im in g dur i ng A ut om ati c A lgor i th m s
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 40/46
EFST
F49L004UA / F49L004BA
10.4 TEMPORARY SECTOR UNPROTECT Operation
Table 14. Temporary Sector Unprotect
Symbol
Description
Rise and Fall Time (See Note)
All Speed Options
Unit
Min
Min
500
ns
T
V
ID
VIDR
Setup Time for Temporary Sector
RESET
4
us
T
RSP
Unprotect
Notes:
Not 100% tested
Figure 24. Temporary Sector Unprotect Timing Diagram
0 or VC C
t V I D R
0 or VC C
RE S E T
C E
t V I D R
P r o g r a m o r E r a s e C o m m a n d S e q u e n c e
W E
tR S P
RY/B Y
Figure 25. Q6 vs Q2 for Erase and Erase Suspend Operations
Ente r E r as e
Suspend Progra m
En ter E m bedde d
Er as in g
Er as e
Suspen d
Er as e
Resu m e
W E
DQ6
DQ2
Er as e
Co m pl e t e
Er as e
Su spend
Read
Er as e
Su spend
Pr o gr a m
Er as e
Notes :
The system can use OE or CE to toggle DQ2 / DQ6, DQ2 toggles only when read at an address within an
erase-suspended.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 41/46
EFST
F49L004UA / F49L004BA
Figure 26. Temporary Sector Unprotect Algorithm
Start
RESET = VID (Note 1)
Program Erase or Program Operation
Operation Completed
RESET = VIH
Temporary Sector Unprotect Completed (Note 2)
Notes :
1. All protected status are temporary unprotect.
VID = 11.5V~12.5V
2. All previously protected sectors are protected again.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 42/46
EFST
F49L004UA / F49L004BA
Figure 27. ID Code Read Timing Waveform
V C C
3V
V I D
V I H
V I L
A D D
A9
V I H
A D D
A0
V I L
tAC C
tA C C
V I H
V I L
A1
A D D
A2~A8
A10~A18
V I H
V I L
V I H
V I L
C E
tC E
V I H
V I L
W E
t O E
V I H
V I L
tD F
tO H
OE
tO H
V I H
V I L
Dat a
DQ 0~ DQ 7
Data Out
B5H/B6 H
Data Out
C 2 H
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 43/46
EFST
F49L004UA / F49L004BA
11. ERASE AND PROGRAMMING PERFORMANCE
Table 15. Erase And Programming Performance (Note.1)
Limits
Parameter
Unit
Typ.(2)
0.7
Max.(3)
Sector Erase Time
Chip Erase Time
15
sec
sec
11
Byte Programming Time
Chip Programming Time
Erase/Program Cycles (1)
9
300
13.5
-
us
4.5
sec
100,000
Cycles
Notes:
1.Not 100% Tested, Excludes external system level over head.
2.Typical values measured at 25°C, 3V.
3.Maximum values measured at 85°C, 2.7V.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0
44/46
EFST
F49L004UA / F49L004BA
12. PACKAGE DIMENSION
32-pin PLCC
D
1
D
c
1
32
30
4
5
29
2
E
3
E
E1
E
2
E
13
21
14
20
1
A
-C-
A
2
A
Seating Plane
-C-
0.020" MIN
b
b
O
e
2
D
3
0.004
D
2
D
2
Symbol
Dimension in mm
Dimension in inch
Norm
Min
Norm
-------
Max
Min
Max
0.140
0.095
A
A 1
A 2
b
3.18
1.53
3.55
2.41
0.125
0.060
-------
-------
-------
2.79 REF
-------
0.110 REF
-------
0.33
0.66
0.20
0.54
0.82
0.36
0.013
0.026
0.008
0.021
0.032
0.014
b2
c
-------
-------
-------
-------
e
1.27 BSC
-------
0.050 BSC
-------
θ
0O
10O
15.11
14.04
6.93
0O
10O
E
14.86
13.90
6.05
14.99
0.585
0.547
0.238
0.590
0.595
0.553
0.273
E 1
E 2
E 3
D
13.97
0.550
-------
-------
10.16 BSC
12.45
0.400 BSC
0.490
12.32
11.36
4.78
12.57
11.50
5.66
0.485
0.447
0.188
0.495
0.453
0.223
D 1
D 2
D 3
11.43
0.450
-------
-------
7.62 BSC
0.300 BSC
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 45/46
EFST
F49L004UA / F49L004BA
Important Notice
All rights reserved.
No part of this document may be reproduced or duplicated in any form
or by any means without the prior permission of EFST.
The contents contained in this document are believed to be accurate at
the time of publication. EFST assumes no responsibility for any error in
this document, and reserves the right to change the products or
specification in this document without notice.
The information contained herein is presented only as a guide or
examples for the application of our products. No responsibility is
assumed by EFST for any infringement of patents, copyrights, or other
intellectual property rights of third parties which may result from its use.
No license, either express , implied or otherwise, is granted under any
patents, copyrights or other intellectual property rights of EFST or
others.
Any semiconductor devices may have inherently a certain rate of
failure. To minimize risks associated with customer's application,
adequate design and operating safeguards against injury, damage, or
loss from such failure, should be provided by the customer when
making application designs.
EFST 's products are not authorized for use in critical applications such
as, but not limited to, life support devices or system, where failure or
abnormal operation may directly affect human lives or cause physical
injury or property damage. If products described here are to be used for
such kinds of application, purchaser must do its own quality assurance
testing appropriate to such applications.
Elite Flash Storage Technology Inc.
Publication Date : Sep. 2003
Revision: 1.0 46/46
相关型号：
©2020 ICPDF网 联系我们和版权申明