B43416A9337A000 [EPCOS]
Capacitors for pulse applications with snap-in and solder lug terminals; 电容器的脉冲应用与管理单元和焊片焊接端子
| 型号： | B43416A9337A000 |
| 厂家： | 
EPCOS |
| 描述： | Capacitors for pulse applications with snap-in and solder lug terminals |
| 文件： | 总15页 (文件大小：1999K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Aluminum electrolytic capacitors
Capacitors for pulse applications
with snap-in and solder lug terminals
Series/Type:
B43415, B43416
Date:
December 2006
EPCOS AG 2007. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Capacitors for pulse applications
B43415, B43416
Compact ꢀ up to 60 °C
Application
Professional flash light generators
Features
Compact design
Outstanding reliability
High charge/discharge proof, polar
PAPR (protection against polarity
reversal)
B43416
B43415
Construction
Aluminum case, fully insulated
Case with safety vent
Terminals
Snap-in
Solder lug
Overview
Tem-
perature
°C
Series
Useful life
Features
VR
CR
µF
V DC
+60
B43416
Snap-in
> 30000 flashes ꢀ Compact
ꢀ Easy PCB mounting
300 ... 500 200 ... 1500
ꢀ Outstanding reliability
ꢀ Low leakage current
ꢀ Low dissipation factor
B43415
Solder lug
1000 ... 6600
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 15
B43415, B43416
Compact ꢀ up to 60 °C
Specifications and characteristics in brief
Rated voltage
Discharge voltage Vdischarge 50 V DC
Rated capacitance CR 200 ... 6600 µF
VR
300 ... 500 V DC
Capacitance
tolerance
∆CR
ꢀ10/+20%
Leakage current
Ileak
(5 min, 20 °C)
Dissipation factor
Useful life
15%
tan δ
> 30000 flashes at:
Case temperature
Flash repetition rate
Requirements:
≤ 60 °C ∆C/C ≤ ±30% of initial value
≥ 2 s
ESR ≤ 3 times initial specified
limit
Max. flashes per week ≤ 10000 Ileak
Charge resistance 10 Ω
≤ initial specified limit
Discharge resistance 0.5 Ω
To IEC 60068-2-6, test Fc:
Displacement amplitude 0.35 mm, frequency range 10 Hz ... 55 Hz,
acceleration max. 5 g, duration 3 × 2 h.
Capacitor mounted by its body which is rigidly clamped to the work
surface.
Vibration resistance test
IEC climatic category
V
R ≤ 400 V DC: 40/060/56 (ꢀ40 °C/+60 °C/56 days damp heat test)
VR > 400 V DC: 25/060/56 (ꢀ25 °C/+60 °C/56 days damp heat test)
Please read Cautions and warnings and
Page 3 of 15
Important notes at the end of this document.
B43416
Compact ꢀ up to 60°C
Dimensional drawing
B43416, snap-in terminals
Dimensions, weights and packing units
d × l
Approx.
weight
g
Packing
units
pcs.
mm
25 × 45
30 × 40
30 × 50
35 × 45
35 × 50
25
36
46
56
70
130
80
80
60
60
Please read Cautions and warnings and
Important notes at the end of this document.
Page 4 of 15
B43415
Compact ꢀ up to 60°C
Dimensional drawing
B43415, solder lug terminals
Dimensions, weights and packing units
dmax × lmax
Lead
Approx. Packing
spacing (LS) weight units
mm
mm
g
pcs.
59
59
42
42
42
42
42
42
28
28
35.8 × 55.8
35.8 × 65.8
40.8 × 65.8
40.8 × 70.8
40.8 × 80.8
40.8 × 90.8
10.0
10.0
10.0
10.0
10.0
10.0
66
82
115
130
150
160
180
190
230
270
40.8 × 105.8 10.0
40.8 × 110.8 10.0
50.8 × 80.8
20.0
50.8 × 100.8 20.0
Please read Cautions and warnings and
Page 5 of 15
Important notes at the end of this document.
B43416
Compact ꢀ up to 60°C
Technical data and ordering codes ꢀ B43416
CR
Case dimensions
d × l
Ileak,max
5 min.
20 °C
mA
Ordering code
100 Hz
20 °C
µF
mm
VR = 300 V DC
1000
1500
30 × 50
35 × 50
2.0
2.7
B43416A3108A000
B43416A3158A000
VR = 330 V DC
1000
1200
35 × 45
35 × 50
2.2
2.5
B43416A8108A000
B43416A8128A000
VR = 360 V DC
560
1100
30 × 40
35 × 50
1.5
2.6
B43416A9567A000
B43416A9118A000
VR = 400 V DC
330
700
25 × 45
35 × 45
1.2
2.0
B43416A9337A000
B43416A9707A000
VR = 500 V DC
200
560
25 × 45
35 × 50
0.9
2.0
B43416A6207A000
B43416A6567A000
Please read Cautions and warnings and
Important notes at the end of this document.
Page 6 of 15
B43415
Compact ꢀ up to 60°C
Technical data and ordering codes ꢀ B43415
CR
Case dimensions
Ileak,max
5 min.
20 °C
mA
Ordering code
100 Hz
20 °C
µF
dmax
× lmax
mm
VR = 300 V DC
2100
3000
4700
6600
35.8 × 65.8
40.8 × 70.8
40.8 × 105.8
50.8 × 100.8
3.4
4.4
6.0
7.7
B43415A3218A000
B43415A3308A000
B43415A3478A000
B43415A3668A000
VR = 330 V DC
2100
3000
3800
5600
40.8 × 65.8
40.8 × 80.8
40.8 × 105.8
50.8 × 100.8
3.7
4.7
5.6
7.3
B43415A8218A000
B43415A8308A000
B43415A8388A000
B43415A8568A000
VR = 360 V DC
2100
3000
40.8 × 65.8
40.8 × 90.8
40.8 × 110.8
3.9
5.0
5.9
B43415A9218A000
B43415A9308A000
B43415A9388A000
3800
VR = 400 V DC
1000
2100
3000
3800
35.8 × 55.8
40.8 × 80.8
40.8 × 110.8
50.8 × 100.8
2.5
4.2
5.4
6.4
B43415A9108A000
B43415B9218A000
B43415B9308A000
B43415B9388A000
VR = 500 V DC
1000
2100
40.8 × 65.8
50.8 × 80.8
2.9
4.9
B43415A6108A000
B43415A6218A000
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 15
B43415, B43416
Compact ꢀ up to 60 °C
Packing of snap-in capacitors
Packing of solder lug capacitors
For ecological reasons the packing is pure cardboard.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 15
B43415, B43416
Compact ꢀ up to 60 °C
General technical information
Capacitance
The DC capacitance is the decisive factor for the energy yield. This characteristic is
approximately 1.2 times the AC capacitance. Since the loss angle can only be determined using
alternating currents and the AC capacitance is measured together with this value, it is usual to
state the AC capacitance. The values are measured at a frequency of 100 Hz.
Leakage current (measuring conditions)
The leakage current value limits quoted by EPCOS apply to the capacitors in new condition.
When the leakage current is determined, the current is measured after the capacitor has been
connected, for a period of five minutes, via a 1 kΩ resistor to a stabilized power supply set to the
rated voltage.
Temperature
The attached diagram shows the temperature dependence of the leakage current. In order to
prevent thermal instabilities, switching loads that can lead to overtemperatures of more than 15 K
shall not be applied.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 15
B43415, B43416
Compact ꢀ up to 60 °C
AC capacitance versus temperature
VR = 350 V DC
Typical behaviour
Dissipation factor tan δ versus temperature
VR = 350 V DC, measuring frequency = 120 Hz
Typical behaviour
Leakage current Ileak versus temperature
Measurement duration = 5 minutes
Typical behaviour
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 15
B43415, B43416
Compact ꢀ up to 60 °C
Questionnaire
Please use the questionnaire when having other, improved or additional technical requirements
which cannot be covered by our standard series.
The characteristic data listed in the questionnaire below are essentially the most important
information for determining design dimensions of electrolytic capacitors for professional
photo flash applications.
Rated capacitance per capacitor
µF
Rated voltage per capacitor
Charge/discharge voltage
Required dimensions: Diameter (max.)
Length (max.)
V DC
V
/
mm
mm
Style of terminals
Ambient temperature
° C
Method of cooling
Discharge conditions
Internal resistance of the discharge tube (if applicable)
Charging resistance (series resistance)
No. of capacitors in series
No. of capacitors in parallel
Flash sequence
Ω
Ω
Pause periods
Other special operating conditions
Expected useful life
flashes
Annual demand of capacitors
For any further support, please contact your nearest EPCOS representative.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 15
B43415, B43416
Compact ꢀ up to 60 °C
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling Al electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 12 of 15
B43415, B43416
Compact ꢀ up to 60 °C
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Safety information
Reference
Chapter "General
technical information"
Polarity
Make sure that polar capacitors are connected
with the right polarity.
1
"Basic construction of
aluminum electrolytic
capacitors"
Reverse voltage
Voltages polarity classes should be prevented by 3.1.6
connecting a diode.
"Reverse voltage"
Upper category
temperature
Do not exceed the upper category temperatur.
7.2
"Maximum permissible
operating temperature"
Maintenance
Make periodic inspections of the capacitors.
10
Before the inspection, make sure that the power "Maintenance"
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
Mounting
position of screw
terminal capacitors
Do not mount the capacitor with the terminals
(safety vent) upside down.
11.1.
"Mounting positions of
capacitors with screw
terminals"
Mounting of
single-ended
capacitors
The internal structure of single-ended capacitors 11.4
might be damaged if excessive force is applied to "Mounting
the lead wires.
considerations for
Avoid any compressive, tensile or flexural stress. single-ended capacitors"
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
Robustness of
terminals
The following maximum tightening torques must
not be exceeded when connecting screw
11.3
"Mounting torques"
terminals:
M5: 2 Nm
M6: 2.5 Nm
Soldering
Do not exceed the specified time or temperature 11.5
limits during soldering. "Soldering"
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 15
B43415, B43416
Compact ꢀ up to 60 °C
Topic
Safety information
Reference
Chapter "General
technical information"
Soldering,
cleaning agents
Do not allow halogenated hydrocarbons to come 11.6
into contact with aluminum electrolytic capacitors. "Cleaning agents"
Passive
Avoid external energy, such as fire or electricity.
8.1
flammability
"Passive flammability"
Active
Avoid overload of the capacitors.
8.2
flammability
"Active flammability"
Reference
Chapter "Capacitors
with screw terminals"
Breakdown strength Do not damage the insulating sleeve, especially
"Screw terminals -
accessories"
of insulating
sleeves
when ring clips are used for mounting.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 14 of 15
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incum-
bent on the customer to check and decide whether an EPCOS product with the properties de-
scribed in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of passive electronic compon-
ents or failure before the end of their usual service life cannot be completely ruled out
in the current state of the art, even if they are operated as specified. In customer applica-
tions requiring a very high level of operational safety and especially in customer applications
in which the malfunction or failure of a passive electronic component could endanger human
life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured
by means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of a passive electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as “hazardous”). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the “General Terms of Delivery for Products and Services in the Electrical In-
dustry” published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, EPCOS-JONES, BAOKE, Alu-X, CeraDiode, CSSP, MLSC,
PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K,
UltraCap, WindCap are trademarks registered or pending in Europe and in other countries.
Further information will be found on the Internet at www.epcos.com/trademarks.
Page 15 of 15
相关型号：
©2020 ICPDF网 联系我们和版权申明