CY7C1470BV33-250AXI [CYPRESS]
72-Mbit (2M x 36/4M x 18/1M x 72) Pipelined SRAM with NoBL⑩ Architecture; 72兆位( 2M ×36 / 4M ×18 / 1M X 72 )流水线SRAM与NoBL⑩架构型号: | CY7C1470BV33-250AXI |
厂家: | CYPRESS |
描述: | 72-Mbit (2M x 36/4M x 18/1M x 72) Pipelined SRAM with NoBL⑩ Architecture |
文件: | 总30页 (文件大小:902K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
72-Mbit (2M x 36/4M x 18/1M x 72)
Pipelined SRAM with NoBL™ Architecture
Features
Functional Description
The CY7C1470BV33, CY7C1472BV33, and CY7C1474BV33
are 3.3V, 2M x 36/4M x 18/1M x 72 Synchronous pipelined burst
SRAMs with No Bus Latency™ (NoBL™) logic, respectively.
They are designed to support unlimited true back-to-back read
or write operations with no wait states. The CY7C1470BV33,
CY7C1472BV33, and CY7C1474BV33 are equipped with the
advanced (NoBL) logic required to enable consecutive read or
write operations with data being transferred on every clock cycle.
This feature dramatically improves the throughput of data in
systems that require frequent read or write transitions. The
CY7C1470BV33, CY7C1472BV33, and CY7C1474BV33 are pin
compatible and functionally equivalent to ZBT devices.
■ Pin-compatible and functionally equivalent to ZBT™
■ Supports 250 MHz bus operations with zero wait states
❐ Available speed grades are 250, 200, and 167 MHz
■ Internally self-timed output buffer control to eliminate the need
to use asynchronous OE
■ Fully registered (inputs and outputs) for pipelined operation
■ Byte Write capability
■ Single 3.3V power supply
■ 3.3V/2.5V IO power supply
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. All data outputs pass through output
registers controlled by the rising edge of the clock. The clock
input is qualified by the Clock Enable (CEN) signal, which when
deasserted suspends operation and extends the previous clock
cycle.
■ Fast clock-to-output time
❐ 3.0 ns (for 250-MHz device)
■ Clock Enable (CEN) pin to suspend operation
■ Synchronous self-timed writes
Write operations are controlled by the Byte Write Selects
■ CY7C1470BV33, CY7C1472BV33 available in
(BWa–BWd
for
CY7C1470BV33,
BWa–BWb
for
JEDEC-standard Pb-free 100-pin TQFP, Pb-free and
non-Pb-free 165-ball FBGA package. CY7C1474BV33
available in Pb-free and non-Pb-free 209-ball FBGA package
CY7C1472BV33, and BWa–BWh for CY7C1474BV33) and a
Write Enable (WE) input. All writes are conducted with on-chip
synchronous self-timed write circuitry.
■ IEEE 1149.1 JTAG Boundary Scan compatible
■ Burst capability—linear or interleaved burst order
■ “ZZ” Sleep Mode option and Stop Clock option
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. To avoid bus contention,
the output drivers are synchronously tri-stated during the data
portion of a write sequence.
Selection Guide
Description
Maximum Access Time
250 MHz
200 MHz
3.0
167 MHz
3.4
Unit
ns
3.0
500
120
Maximum Operating Current
500
450
mA
mA
Maximum CMOS Standby Current
120
120
Cypress Semiconductor Corporation
Document #: 001-15031 Rev. *C
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised February 29, 2008
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Logic Block Diagram – CY7C1470BV33 (2M x 36)
ADDRESS
REGISTER
A0, A1,
A
0
A1
A0
A1'
A0'
D1
D0
Q1
Q0
BURST
LOGIC
MODE
ADV/LD
CLK
CEN
C
C
WRITE ADDRESS
REGISTER
WRITE ADDRESS
REGISTER 2
1
O
O
S
U
D
A
T
U
T
T
P
U
T
E
N
S
P
U
T
ADV/LD
A
E
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
R
E
G
I
MEMORY
ARRAY
B
U
F
F
E
R
S
S
T
E
E
R
I
DQ s
DQ P
DQ P
DQ P
DQ P
WRITE
DRIVERS
BW
a
a
b
c
A
M
P
BW
BW
BW
b
c
S
T
E
R
S
d
d
S
WE
E
E
N
G
INPUT
REGISTER
INPUT
REGISTER 0
E
E
1
OE
READ LOGIC
CE1
CE2
CE3
SLEEP
CONTROL
ZZ
Logic Block Diagram – CY7C1472BV33 (4M x 18)
ADDRESS
REGISTER
A0, A1,
A
0
A1
A0
A1'
A0'
D1
D0
Q1
Q0
BURST
LOGIC
MODE
ADV/LD
CLK
CEN
C
C
WRITE ADDRESS
REGISTER
WRITE ADDRESS
REGISTER 2
1
O
U
T
O
U
T
P
U
T
S
E
P
U
T
D
A
T
ADV/LD
N
S
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
A
R
E
G
I
MEMORY
ARRAY
E
B
U
F
F
E
R
S
DQ s
DQ P
DQ P
WRITE
DRIVERS
BW
BW
a
S
T
E
E
R
I
A
M
P
a
b
S
T
E
R
S
b
S
N
G
WE
E
E
INPUT
REGISTER
INPUT
REGISTER 0
E
E
1
OE
CE1
CE2
CE3
READ LOGIC
Sleep
Control
ZZ
Document #: 001-15031 Rev. *C
Page 2 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Logic Block Diagram – CY7C1474BV33 (1M x 72)
ADDRESS
REGISTER
A0, A1,
A
0
A1
A0
A1'
A0'
D1
D0
Q1
Q0
BURST
LOGIC
MODE
ADV/LD
CLK
CEN
C
C
WRITE ADDRESS
REGISTER
WRITE ADDRESS
REGISTER 2
1
O
U
T
O
U
T
P
U
T
S
E
P
U
T
D
A
T
ADV/LD
N
S
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
A
BW
BW
BW
BW
BW
a
R
E
G
I
MEMORY
ARRAY
E
B
U
F
F
E
R
S
DQ s
DQ P
DQ P
DQ P
DQ P
DQ P
DQ P
DQ P
DQ P
WRITE
DRIVERS
b
S
T
E
E
R
I
A
M
P
a
b
c
c
d
e
S
T
E
R
S
S
d
e
f
BW
f
N
G
BW
g
E
E
BW
h
g
h
WE
INPUT
REGISTER
INPUT
REGISTER 0
E
E
1
OE
CE1
CE2
CE3
READ LOGIC
Sleep
Control
ZZ
Document #: 001-15031 Rev. *C
Page 3 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Pin Configurations
Figure 1. 100-Pin TQFP Pinout
DQPc
DQc
DQc
1
2
3
4
5
6
7
8
NC
NC
NC
DDQ
1
2
3
4
5
6
7
8
A
NC
NC
DQPb
DQb
DQb
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
V
V
DDQ
V
V
DDQ
DDQ
V
V
V
SS
V
SS
SS
SS
DQc
DQc
NC
NC
DQb
NC
DQb
DQb
DQb
DQb
DQPa
DQa
DQa
DQc
DQc
9
DQb
9
V
V
SS
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
V
SS
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
V
SS
SS
V
V
DDQ
DDQ
V
V
DQa
DQa
DDQ
DDQ
DQc
DQc
NC
DQb
DQb
DQb
DQb
NC
V
V
SS
SS
V
V
DD
NC
DD
NC
CY7C1472BV33
(4M x 18)
CY7C1470BV33
(2M x 36)
NC
NC
V
V
DD
DD
V
V
SS
SS
ZZ
ZZ
DQa
DQa
DQd
DQb
DQb
DQa
DQa
V
DQd
V
V
DDQ
DDQ
V
DDQ
DDQ
V
V
SS
V
SS
V
SS
SS
DQd
DQd
DQd
DQd
DQa
DQa
DQa
DQa
DQb
DQb
DQPb
NC
DQa
DQa
NC
NC
V
SS
V
V
V
SS
SS
SS
V
V
DDQ
V
DDQ
V
DDQ
DDQ
DQd
DQd
DQPd
DQa
DQa
DQPa
NC
NC
NC
NC
NC
NC
Document #: 001-15031 Rev. *C
Page 4 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Pin Configurations (continued)
165-Ball FBGA (15 x 17 x 1.4 mm) Pinout
CY7C1470BV33 (2M x 36)
1
2
A
3
4
BW
BW
V
5
6
7
8
9
A
10
A
11
NC
NC/576M
A
B
C
D
CE3
CLK
ADV/LD
OE
CE
BW
b
CEN
WE
1
c
NC/1G
A
NC
DQ
CE2
A
A
NC
DQ
NC
BW
d
a
DQP
V
V
V
V
V
V
V
V
V
V
V
DQP
DQ
c
DDQ
SS
SS
SS
SS
SS
SS
DDQ
DDQ
b
DQ
V
V
V
V
V
V
V
V
c
c
DDQ
DD
SS
SS
DD
b
b
DQ
DQ
DQ
DQ
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
DQ
DQ
DQ
DQ
DQ
DQ
E
F
c
c
c
c
DDQ
DDQ
DDQ
DD
SS
SS
SS
DD
DDQ
DDQ
DDQ
b
b
b
b
DQ
V
V
V
c
DD
DD
DD
DD
SS
SS
SS
SS
SS
SS
DD
b
b
DQ
V
V
V
G
H
J
c
SS
SS
DD
NC
NC
DQ
NC
V
V
V
NC
NC
DQ
ZZ
SS
SS
DD
DQ
V
V
V
V
V
DQ
a
d
d
DDQ
DDQ
DDQ
DDQ
SS
SS
DD
DDQ
DDQ
DDQ
DDQ
a
DQ
DQ
DQ
DQ
V
V
V
V
V
V
V
V
V
V
V
DQ
DQ
DQ
DQ
DQ
DQ
K
L
d
d
d
d
DD
DD
DD
SS
SS
SS
SS
SS
DD
a
a
a
a
a
a
DQ
V
V
V
d
SS
SS
DD
DQ
V
V
V
V
V
M
N
P
d
SS
SS
DD
DQP
NC
A
V
NC
NC
A1
NC
V
NC
A
DQP
a
d
DDQ
SS
SS
DDQ
NC/144M
MODE
A
TDI
TDO
A
NC/288M
A
A
A
A
A
A
A
TMS
A0
TCK
A
A
R
CY7C1472BV33 (4M x 18)
1
NC/576M
NC/1G
NC
2
A
3
4
5
NC
6
7
8
9
A
10
A
11
A
A
B
C
D
CE1
CE2
BWb
NC
CE3
CLK
VSS
VSS
CEN
ADV/LD
A
A
A
NC
BWa
VSS
VSS
WE
VSS
VSS
OE
VSS
VDD
NC
DQb
VDDQ
VDDQ
VSS
VDD
VDDQ
VDDQ
NC
NC
DQPa
DQa
NC
NC
NC
DQb
DQb
DQb
NC
VDDQ
VDDQ
VDDQ
NC
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
NC
NC
NC
DQa
DQa
DQa
ZZ
E
F
NC
NC
G
H
J
NC
NC
DQb
DQb
DQb
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
DQa
DQa
DQa
NC
NC
NC
K
L
NC
NC
DQb
DQPb
NC
NC
A
VDDQ
VDDQ
A
VDD
VSS
A
VSS
NC
VSS
NC
A1
VSS
NC
VDD
VSS
A
VDDQ
VDDQ
A
DQa
NC
A
NC
NC
M
N
P
NC/144M
TDI
TDO
NC/288M
A
MODE
A
A
TMS
A0
TCK
A
A
A
A
R
Document #: 001-15031 Rev. *C
Page 5 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Pin Configurations (continued)
209-Ball FBGA (14 x 22 x 1.76 mm) Pinout
CY7C1474BV33 (1M × 72)
1
2
3
4
5
6
7
8
9
10
11
DQg
DQg
DQg
DQg
A
CE2
A
ADV/LD
WE
A
A
CE3
A
DQb
DQb
DQb
DQb
DQb
DQb
DQb
A
B
BWSc
BWSg
NC
BWSb
BWSf
DQg
DQg
DQg
DQg
BWSh
VSS
BWSd NC/576M CE1
NC
NC
BWSe
NC
BWSa
VSS
C
D
NC/1G
OE
NC
DQb
DQPb
DQf
E
F
DQPg
DQc
DQPc
DQc
VDDQ
VDDQ
VDDQ
VSS
VDDQ
VSS
VDDQ
VSS
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VDD
NC
VDD
VSS
VDD
DQPf
DQf
VSS
VDDQ
VSS
VSS
VDDQ
VSS
G
H
J
DQc
DQc
DQc
NC
VDDQ
VSS
DQf
DQf
DQf
VSS
VDD
VSS
VDD
VSS
VDD
VSS
VDD
NC
A
DQc
DQc
NC
NC
DQf
DQf
NC
VDDQ
DQc
NC
VDDQ
VDDQ
NC
VDDQ
CLK
NC
DQf
NC
K
L
CEN
NC
NC
NC
DQh
DQh
DQh
VDDQ
VSS
VDDQ
VSS
VDDQ
VDDQ
VSS
VDDQ
VSS
VDDQ
VSS
DQa
DQa
DQa
M
N
P
R
T
NC
VSS
VDDQ
VSS
VDDQ
NC
DQh
DQh
DQh
VSS
VDD
VSS
DQa
DQa
DQa
VDDQ
DQh
DQh
DQPd
DQd
DQd
NC
ZZ
DQa
DQa
DQPa
DQe
DQe
VSS
VDDQ
VDDQ
VDD
NC
A
DQPh
DQd
DQd
DQd
DQd
VDDQ
VDD
DQPe
DQe
DQe
DQe
DQe
VSS
VSS
NC
A
MODE
A
U
V
W
A
NC/288M
NC/144M
A
A
A1
A
DQd
DQd
A
A
A
A
DQe
DQe
TDI
TDO
TCK
A0
A
TMS
Document #: 001-15031 Rev. *C
Page 6 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Table 1. Pin Definitions
Pin Name
A0
A1
A
IO Type
Pin Description
Address Inputs Used to Select One of the Address Locations. Sampled at the rising edge
Input-
Synchronous of the CLK.
BWa
BWb
BWc
BWd
BWe
BWf
Input-
Byte Write Select Inputs, Active LOW. Qualified with WE to conduct writes to the SRAM.
Synchronous Sampled on the rising edge of CLK. BWa controls DQa and DQPa, BWb controls DQb and DQPb,
BWc controls DQc and DQPc, BWd controls DQd and DQPd, BWe controls DQe and DQPe, BWf
controls DQf and DQPf, BWg controls DQg and DQPg, BWh controls DQh and DQPh.
BWg
BWh
WE
Input-
Write Enable Input, Active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This
Synchronous signal must be asserted LOW to initiate a write sequence.
ADV/LD
Input- Advance/Load Input Used to Advance the On-chip Address Counter or Load a New
Synchronous Address. When HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When
LOW, a new address can be loaded into the device for an access. After being deselected, ADV/LD
must be driven LOW to load a new address.
CLK
CE1
CE2
CE3
OE
Input-
Clock
Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN.
CLK is only recognized if CEN is active LOW.
Input-
Chip Enable 1 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE2 and CE3 to select or deselect the device.
Input-
Chip Enable 2 Input, Active HIGH. Sampled on the rising edge of CLK. Used in conjunction
Synchronous with CE1 and CE3 to select or deselect the device.
Input-
Chip Enable 3 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE1 and CE2 to select or deselect the device.
Input-
Output Enable, Active LOW. Combined with the synchronous logic block inside the device to
Asynchronous control the direction of the IO pins. When LOW, the IO pins are enabled to behave as outputs.
When deasserted HIGH, IO pins are tri-stated, and act as input data pins. OE is masked during
the data portion of a write sequence, during the first clock when emerging from a deselected state
and when the device has been deselected.
CEN
DQS
Input-
Clock Enable Input, Active LOW. When asserted LOW the clock signal is recognized by the
Synchronous SRAM. When deasserted HIGH the clock signal is masked. Since deasserting CEN does not
deselect the device, CEN can be used to extend the previous cycle when required.
IO-
Bidirectional Data IO Lines. As inputs, they feed into an on-chip data register that is triggered
Synchronous by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by A[17:0] during the previous clock rise of the read cycle. The direction of the pins is
controlled by OE and the internal control logic. When OE is asserted LOW, the pins can behave
as outputs. When HIGH, DQa–DQd are placed in a tri-state condition. The outputs are automat-
ically tri-stated during the data portion of a write sequence, during the first clock when emerging
from a deselected state, and when the device is deselected, regardless of the state of OE.
DQPX
IO-
Bidirectional Data Parity IO Lines. Functionally, these signals are identical to DQX. During write
Synchronous sequences, DQPa is controlled by BWa, DQPb is controlled by BWb, DQPc is controlled by BWc,
and DQPd is controlled by BWd, DQPe is controlled by BWe, DQPf is controlled by BWf, DQPg
is controlled by BWg, DQPh is controlled by BWh.
MODE
TDO
TDI
Input Strap Pin Mode Input. Selects the burst order of the device. Tied HIGH selects the interleaved burst order.
Pulled LOW selects the linear burst order. MODE must not change states during operation. When
left floating MODE defaults HIGH, to an interleaved burst order.
JTAG Serial
Output
Serial Data Out to the JTAG Circuit. Delivers data on the negative edge of TCK.
Synchronous
JTAG Serial Input Serial Data In to the JTAG Circuit. Sampled on the rising edge of TCK.
Synchronous
Document #: 001-15031 Rev. *C
Page 7 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Table 1. Pin Definitions (continued)
Pin Name
IO Type
Pin Description
TMS
Test Mode Select This Pin Controls the Test Access Port State Machine. Sampled on the rising edge of TCK.
Synchronous
TCK
VDD
VDDQ
VSS
NC
JTAG Clock
Clock Input to the JTAG Circuitry.
Power Supply Power Supply Inputs to the Core of the Device.
IO Power Supply Power Supply for the IO Circuitry.
Ground
Ground for the Device. Should be connected to ground of the system.
–
–
No Connects. This pin is not connected to the die.
NC(144M,
288M,
These Pins are Not Connected. They are used for expansion to the 144M, 288M, 576M, and
1G densities.
576M, 1G)
ZZ
Input-
ZZ “Sleep” Input. This active HIGH input places the device in a non-time critical “sleep” condition
Asynchronous with data integrity preserved. During normal operation, this pin must be LOW or left floating.
ZZ pin has an internal pull-down.
register and onto the data bus within 3.0 ns (250-MHz device)
Functional Overview
provided OE is active LOW. After the first clock of the read
access the output buffers are controlled by OE and the internal
control logic. OE must be driven LOW to drive out the requested
data. During the second clock, a subsequent operation (read,
write, or deselect) can be initiated. Deselecting the device is also
pipelined. Therefore, when the SRAM is deselected at clock rise
by one of the chip enable signals, its output tri-states following
the next clock rise.
The CY7C1470BV33, CY7C1472BV33, and CY7C1474BV33
are synchronous-pipelined Burst NoBL SRAMs designed specif-
ically to eliminate wait states during read or write transitions. All
synchronous inputs pass through input registers controlled by
the rising edge of the clock. The clock signal is qualified with the
Clock Enable input signal (CEN). If CEN is HIGH, the clock signal
is not recognized and all internal states are maintained. All
synchronous operations are qualified with CEN. All data outputs
pass through output registers controlled by the rising edge of the
clock. Maximum access delay from the clock rise (tCO) is 3.0 ns
(250-MHz device).
Burst Read Accesses
The CY7C1470BV33, CY7C1472BV33, and CY7C1474BV33
have an on-chip burst counter that enables the user to supply a
single address and conduct up to four reads without reasserting
the address inputs. ADV/LD must be driven LOW to load a new
address into the SRAM, as described in the Single Read
Accesses section. The sequence of the burst counter is deter-
mined by the MODE input signal. A LOW input on MODE selects
a linear burst mode, a HIGH selects an interleaved burst
sequence. Both burst counters use A0 and A1 in the burst
sequence, and wraps around when incremented sufficiently. A
HIGH input on ADV/LD increments the internal burst counter
regardless of the state of chip enables inputs or WE. WE is
latched at the beginning of a burst cycle. Therefore, the type of
access (read or write) is maintained throughout the burst
sequence.
Accesses can be initiated by asserting all three Chip Enables
(CE1, CE2, CE3) active at the rising edge of the clock. If CEN is
active LOW and ADV/LD is asserted LOW, the address
presented to the device is latched. The access can either be a
read or write operation, depending on the status of the Write
Enable (WE). BW[x] can be used to conduct Byte Write opera-
tions.
Write operations are qualified by the Write Enable (WE). All
writes are simplified with on-chip synchronous self-timed write
circuitry.
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) simplify depth expansion. All
operations (reads, writes, and deselects) are pipelined. ADV/LD
must be driven LOW after the device has been deselected to
load a new address for the next operation.
Single Write Accesses
Write accesses are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, and (3) the signal WE is
asserted LOW. The address presented to the address inputs is
loaded into the Address Register. The write signals are latched
into the Control Logic block.
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, (3) the input signal WE is
deasserted HIGH, and (4) ADV/LD is asserted LOW. The
address presented to the address inputs is latched into the
Address Register and presented to the memory core and control
logic. The control logic determines that a read access is in
progress and allows the requested data to propagate to the input
of the output register. At the rising edge of the next clock the
requested data is allowed to propagate through the output
On the subsequent clock rise the data lines are automatically
tri-stated regardless of the state of the OE input signal. This
allows the external logic to present the data on DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1470BV33, DQa,b/DQPa,b for
CY7C1472BV33, and DQa,b,c,d,e,f,g,h/DQPa,b,c,d,e,f,g,h for
CY7C1474BV33). In addition, the address for the subsequent
Document #: 001-15031 Rev. *C
Page 8 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
access (read, write, or deselect) is latched into the Address
Register (provided the appropriate control signals are asserted).
clock rise, the Chip Enables (CE1, CE2, and CE3) and WE inputs
are ignored and the burst counter is incremented. The correct
BW (BWa,b,c,d for CY7C1470BV33, BWa,b for CY7C1472V33,
and BWa,b,c,d,e,f,g,h for CY7C1474BV33) inputs must be driven
in each cycle of the burst write to write the correct bytes of data.
On the next clock rise the data presented to DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1470BV33, DQa,b/DQPa,b for
CY7C1472BV33, and DQa,b,c,d,e,f,g,h/DQPa,b,c,d,e,f,g,h for
CY7C1474BV33) (or a subset for byte write operations, see
“Partial Write Cycle Description” on page 11 for details) inputs is
latched into the device and the write is complete.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
nor is the completion of the operation guaranteed. The device
must be deselected before entering the “sleep” mode. CE1, CE2,
and CE3, must remain inactive for the duration of tZZREC after the
ZZ input returns LOW.
The data written during the Write operation is controlled by BW
(BWa,b,c,d for CY7C1470BV33, BWa,b for CY7C1472BV33, and
BWa,b,c,d,e,f,g,h
for
CY7C1474BV33)
signals.
The
CY7C1470BV33, CY7C1472BV33, and CY7C1474BV33
provides Byte Write capability that is described in “Partial Write
Cycle Description” on page 11. Asserting the Write Enable input
(WE) with the selected BW input selectively writes to only the
desired bytes. Bytes not selected during a Byte Write operation
remain unaltered. A synchronous self-timed write mechanism
has been provided to simplify the write operations. Byte Write
capability has been included to greatly simplify read, modify, or
write sequences, which can be reduced to simple Byte Write
operations.
Table 2. Interleaved Burst Address Table
(MODE = Floating or VDD
)
First
Address
Second
Address
Third
Address
Fourth
Address
Because the CY7C1470BV33, CY7C1472BV33, and
CY7C1474BV33 are common IO devices, data must not be
driven into the device while the outputs are active. The OE can
be deasserted HIGH before presenting data to the DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1470BV33, DQa,b/DQPa,b for
CY7C1472BV33, and DQa,b,c,d,e,f,g,h/DQPa,b,c,d,e,f,g,h for
CY7C1474BV33) inputs. Doing so tri-states the output drivers.
As a safety precaution, DQ and DQP (DQa,b,c,d/DQPa,b,c,d for
CY7C1470BV33, DQa,b/DQPa,b for CY7C1472BV33, and
DQa,b,c,d,e,f,g,h/DQPa,b,c,d,e,f,g,h for CY7C1474BV33) are
automatically tri-stated during the data portion of a write cycle,
regardless of the state of OE.
A1,A0
00
A1,A0
01
A1,A0
10
A1,A0
11
01
00
11
10
10
11
00
01
11
10
01
00
Table 3. Linear Burst Address Table (MODE = GND)
First
Address
Second
Address
Third
Address
Fourth
Address
Burst Write Accesses
A1,A0
00
A1,A0
01
A1,A0
10
A1,A0
11
The CY7C1470BV33, CY7C1472BV33, and CY7C1474BV33
has an on-chip burst counter that enables the user to supply a
single address and conduct up to four write operations without
reasserting the address inputs. ADV/LD must be driven LOW to
load the initial address, as described in “Single Write Accesses”
on page 8. When ADV/LD is driven HIGH on the subsequent
01
10
11
00
10
11
00
01
11
00
01
10
ZZ Mode Electrical Characteristics
Parameter
IDDZZ
Description
Sleep mode standby current
Device operation to ZZ
ZZ recovery time
Test Conditions
Min
Max
Unit
mA
ns
ZZ > VDD − 0.2V
120
tZZS
ZZ > VDD − 0.2V
2tCYC
tZZREC
tZZI
ZZ < 0.2V
2tCYC
0
ns
ZZ active to sleep current
ZZ Inactive to exit sleep current
This parameter is sampled
This parameter is sampled
2tCYC
ns
tRZZI
ns
Document #: 001-15031 Rev. *C
Page 9 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Table 4. Truth Table
The truth table for CY7C1470BV33, CY7C1472BV33, and CY7C1474BV33 follows.[1, 2, 3, 4, 5, 6, 7]
Operation
Address Used
None
CE
H
ZZ
L
ADV/LD WE
BWx
X
OE
X
CEN CLK
DQ
Deselect Cycle
L
X
X
L
L
L-H
L-H
Tri-State
Tri-State
Continue
None
X
L
H
X
X
Deselect Cycle
Read Cycle
(Begin Burst)
External
Next
L
X
L
L
L
L
L
L
L
L
L
L
H
L
H
L
H
X
H
X
L
X
X
X
X
L
L
L
L
L
L
L
L
L
L
L
H
X
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
L-H
X
Data Out (Q)
Data Out (Q)
Tri-State
Tri-State
Data In (D)
Data In (D)
Tri-State
Tri-State
-
Read Cycle
(Continue Burst)
NOP/Dummy Read
(Begin Burst)
External
Next
H
H
X
X
X
X
X
X
Dummy Read
(Continue Burst)
X
L
H
L
Write Cycle
(Begin Burst)
External
Next
Write Cycle
(Continue Burst)
X
L
H
L
X
L
L
NOP/Write Abort
(Begin Burst)
None
H
H
X
X
Write Abort
(Continue Burst)
Next
X
X
X
H
X
X
X
X
X
Ignore Clock Edge
(Stall)
Current
None
Sleep Mode
Tri-State
Notes
1. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for ALL Chip Enables active. BWx = 0 signifies at least one Byte Write Select is active, BWx = Valid
signifies that the desired byte write selects are asserted, see “Partial Write Cycle Description” on page 11 for details.
2. Write is defined by WE and BW
. See “Partial Write Cycle Description” on page 11 for details.
[a:d]
3. When a write cycle is detected, all IOs are tri-stated, even during Byte Writes.
4. The DQ and DQP pins are controlled by the current cycle and the OE signal.
5. CEN = H inserts wait states.
6. Device powers up deselected with the IOs in a tri-state condition, regardless of OE.
7. OE is asynchronous and is not sampled with the clock rise. It is masked internally during Write cycles. During a read cycle DQ and DQP
= tri-state when OE is
[a:d]
s
inactive or when the device is deselected, and DQ = data when OE is active.
s
Document #: 001-15031 Rev. *C
Page 10 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Table 5. Partial Write Cycle Description
The partial write cycle description for CY7C1470BV33, CY7C1472BV33, and CY7C1474BV33 follows.[1, 2, 3, 8]
Function (CY7C1470BV33)
WE
H
L
BWd
X
H
H
H
H
H
H
H
H
L
BWc
X
H
H
H
H
L
BWb
X
H
H
L
BWa
X
H
L
Read
Write – No bytes written
Write Byte a – (DQa and DQPa)
Write Byte b – (DQb and DQPb)
Write Bytes b, a
L
L
H
L
L
L
Write Byte c – (DQc and DQPc)
Write Bytes c, a
L
H
H
L
H
L
L
L
Write Bytes c, b
L
L
H
L
Write Bytes c, b, a
L
L
L
Write Byte d – (DQd and DQPd)
Write Bytes d, a
L
H
H
H
H
L
H
H
L
H
L
L
L
Write Bytes d, b
L
L
H
L
Write Bytes d, b, a
L
L
L
Write Bytes d, c
L
L
H
H
L
H
L
Write Bytes d, c, a
L
L
L
Write Bytes d, c, b
L
L
L
H
L
Write All Bytes
L
L
L
L
Function (CY7C1472BV33)
WE
BWb
BWa
Read
H
L
L
L
L
x
H
H
L
x
H
L
Write – No Bytes Written
Write Byte a – (DQa and DQPa)
Write Byte b – (DQb and DQPb)
Write Both Bytes
H
L
L
Function (CY7C1474BV33)
WE
BWx
Read
H
L
L
L
x
Write – No Bytes Written
Write Byte X − (DQx and DQPx)
Write All Bytes
H
L
All BW = L
Note
8. Table lists only a partial listing of the Byte Write combinations. Any combination of BW
is valid. Appropriate Write is based on which Byte Write is active.
[a:d]
Document #: 001-15031 Rev. *C
Page 11 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Test Mode Select (TMS)
IEEE 1149.1 Serial Boundary Scan (JTAG)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to leave
this ball unconnected if the TAP is not used. The ball is pulled up
internally, resulting in a logic HIGH level.
The CY7C1470BV33, CY7C1472BV33, and CY7C1474BV33
incorporates a serial boundary scan test access port (TAP). This
port operates in accordance with IEEE Standard 1149.1-1990
but does not have the set of functions required for full 1149.1
compliance. These functions from the IEEE specification are
excluded because their inclusion places an added delay in the
critical speed path of the SRAM. Note that the TAP controller
functions in a manner that does not conflict with the operation of
other devices using 1149.1 fully compliant TAPs. The TAP
operates using JEDEC-standard 3.3V or 2.5V IO logic levels.
Test Data-In (TDI)
The TDI ball is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. For information about
loading the instruction register, see the TAP Controller State
Diagram. TDI is internally pulled up and can be unconnected if
the TAP is unused in an application. TDI is connected to the most
significant bit (MSB) of any register. (See TAP Controller Block
Diagram.)
The CY7C1470BV33, CY7C1472BV33, and CY7C1474BV33
contains a TAP controller, instruction register, boundary scan
register, bypass register, and ID register.
Disabling the JTAG Feature
Test Data-Out (TDO)
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are inter-
nally pulled up and may be unconnected. They may alternately
be connected to VDD through a pull up resistor. TDO must be left
unconnected. During power up, the device comes up in a reset
state, which does not interfere with the operation of the device.
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current state
of the TAP state machine. The output changes on the falling edge
of TCK. TDO is connected to the least significant bit (LSB) of any
register. (See TAP Controller State Diagram.)
Figure 3. TAP Controller Block Diagram
Figure 2. TAP Controller State Diagram
0
TEST-LOGIC
1
RESET
0
Bypass Register
2
1
0
0
0
1
1
1
RUN-TEST/
IDLE
SELECT
DR-SCAN
SELECT
IR-SCAN
0
Selection
Circuitry
Selection
Circuitry
Instruction Register
31 30 29
Identification Register
0
0
TDI
TDO
1
1
.
.
. 2 1
CAPTURE-DR
CAPTURE-IR
0
0
x
.
.
.
.
. 2 1
SHIFT-DR
0
SHIFT-IR
0
Boundary Scan Register
1
1
1
1
EXIT1-DR
EXIT1-IR
0
0
PAUSE-DR
0
PAUSE-IR
1
0
TCK
TAP CONTROLLER
TM S
1
0
0
EXIT2-DR
1
EXIT2-IR
1
Performing a TAP Reset
UPDATE-DR
UPDATE-IR
A RESET is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
1
0
1
0
During power up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
TAP Registers
Test Access Port (TAP)
Registers are connected between the TDI and TDO balls and
scans data into and out of the SRAM test circuitry. Only one
register can be selected at a time through the instruction register.
Data is serially loaded into the TDI ball on the rising edge of TCK.
Data is output on the TDO ball on the falling edge of TCK.
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Document #: 001-15031 Rev. *C
Page 12 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Instruction Register
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO balls. To execute
the instruction after it is shifted in, the TAP controller is moved
into the Update-IR state.
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO balls as shown in the “TAP Controller Block Diagram”
on page 12. During power up, the instruction register is loaded
with the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as described
in the previous section.
EXTEST
EXTEST is a mandatory 1149.1 instruction which is executed
whenever the instruction register is loaded with all 0s. EXTEST
is not implemented in this SRAM TAP controller, and therefore
this device is not compliant to 1149.1. The TAP controller does
recognize an all-0 instruction.
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary ‘01’ pattern to enable fault
isolation of the board-level serial test data path.
Bypass Register
When an EXTEST instruction is loaded into the instruction
register, the SRAM responds as if a SAMPLE/PRELOAD
instruction has been loaded. There is one difference between the
two instructions. Unlike the SAMPLE/PRELOAD instruction,
EXTEST places the SRAM outputs in a High-Z state.
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This shifts data through the SRAM with
minimal delay. The bypass register is set LOW (VSS) when the
BYPASS instruction is executed.
IDCODE
Boundary Scan Register
The IDCODE instruction loads a vendor-specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO balls and shifts the IDCODE out of the
device when the TAP controller enters the Shift-DR state.
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM.
The boundary scan register is loaded with the contents of the
RAM IO ring when the TAP controller is in the Capture-DR state
and is then placed between the TDI and TDO balls when the
controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used to
capture the contents of the IO ring.
The IDCODE instruction is loaded into the instruction register
during power up or whenever the TAP controller is in a test logic
reset state.
SAMPLE Z
The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO balls when the TAP controller is in a
Shift-DR state. It also places all SRAM outputs into a High-Z
state.
The Boundary Scan Order tables show the order in which the bits
are connected. Each bit corresponds to one of the bumps on the
SRAM package. The MSB of the register is connected to TDI and
the LSB is connected to TDO.
SAMPLE/PRELOAD
Identification (ID) Register
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. The
PRELOAD portion of this instruction is not implemented, so the
device TAP controller is not fully 1149.1 compliant.
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in “Identification Register Definitions” on
page 17.
When the SAMPLE/PRELOAD instruction is loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and bidirectional balls is
captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because there
is a large difference in the clock frequencies, it is possible that
during the Capture-DR state, an input or output may undergo a
transition. The TAP may then try to capture a signal while in
transition (metastable state). This does not harm the device, but
there is no guarantee as to the value that is captured.
Repeatable results may not be possible.
TAP Instruction Set
Overview
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in “Identification
Codes” on page 17. Three of these instructions are listed as
RESERVED and must not be used. The other five instructions
are described in this section in detail.
The TAP controller used in this SRAM is not fully compliant to the
1149.1 convention because some of the mandatory 1149.1
instructions are not fully implemented.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture setup plus hold
time (tCS plus tCH).
The TAP controller cannot be used to load address data or
control signals into the SRAM and cannot preload the IO buffers.
The SRAM does not implement the 1149.1 commands EXTEST
or INTEST or the PRELOAD portion of SAMPLE/PRELOAD;
rather, it performs a capture of the IO ring when these instruc-
tions are executed.
The SRAM clock input might not be captured correctly if there is
no way in a design to stop (or slow) the clock during a
SAMPLE/PRELOAD instruction. If this is an issue, it is still
Document #: 001-15031 Rev. *C
Page 13 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
possible to capture all other signals and simply ignore the value
of the CLK captured in the boundary scan register.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO balls. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO balls.
Note that since the PRELOAD part of the command is not imple-
mented, putting the TAP to the Update-DR state while performing
a SAMPLE/PRELOAD instruction has the same effect as the
Pause-DR command.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
Figure 4. TAP Timing
1
2
3
4
5
6
Test Clock
(TCK)
t
t
t
CYC
TH
TL
t
t
t
t
TM SS
TDIS
TM SH
Test M ode Select
(TM S)
TDIH
Test Data-In
(TDI)
t
TDOV
t
TDOX
Test Data-Out
(TDO)
DON’T CARE
UNDEFINED
Document #: 001-15031 Rev. *C
Page 14 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
TAP AC Switching Characteristics
Over the Operating Range[9, 10]
Parameter
Clock
tTCYC
tTF
Description
Min
Max
Unit
TCK Clock Cycle Time
TCK Clock Frequency
TCK Clock HIGH time
TCK Clock LOW time
50
ns
MHz
ns
20
tTH
20
20
tTL
ns
Output Times
tTDOV
TCK Clock LOW to TDO Valid
10
ns
ns
tTDOX
TCK Clock LOW to TDO Invalid
0
Setup Times
tTMSS
TMS Setup to TCK Clock Rise
TDI Setup to TCK Clock Rise
Capture Setup to TCK Rise
5
5
5
ns
ns
ns
tTDIS
tCS
Hold Times
tTMSH
TMS Hold after TCK Clock Rise
TDI Hold after Clock Rise
5
5
5
ns
ns
ns
tTDIH
tCH
Capture Hold after Clock Rise
Notes
9.
t
and t refer to the setup and hold time requirements of latching data from the boundary scan register.
CS CH
10. Test conditions are specified using the load in TAP AC Test Conditions. t /t = 1 ns.
R
F
Document #: 001-15031 Rev. *C
Page 15 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
3.3V TAP AC Test Conditions
2.5V TAP AC Test Conditions
Input pulse levels.................................................VSS to 3.3V
Input rise and fall times....................................................1 ns
Input timing reference levels........................................... 1.5V
Output reference levels .................................................. 1.5V
Test load termination supply voltage .............................. 1.5V
Input pulse levels.................................................VSS to 2.5V
Input rise and fall time .....................................................1 ns
Input timing reference levels ........................................ 1.25V
Output reference levels ................................................ 1.25V
Test load termination supply voltage ............................ 1.25V
3.3V TAP AC Output Load Equivalent
2.5V TAP AC Output Load Equivalent
1.25V
1.5V
50Ω
50Ω
TDO
TDO
ZO= 50Ω
20pF
ZO= 50Ω
20pF
TAP DC Electrical Characteristics And Operating Conditions
(0°C < TA < +70°C; VDD = 3.135V to 3.6V unless otherwise noted)[11]
Parameter
VOH1
Description
Test Conditions
Min
2.4
2.0
2.9
2.1
Max
Unit
Output HIGH Voltage IOH = –4.0 mA,VDDQ = 3.3V
IOH = –1.0 mA,VDDQ = 2.5V
V
V
V
V
V
V
V
V
V
V
V
V
µA
VOH2
VOL1
VOL2
VIH
Output HIGH Voltage IOH = –100 µA
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V
VDDQ = 2.5V
Output LOW Voltage IOL = 8.0 mA
IOL = 1.0 mA
0.4
0.4
Output LOW Voltage IOL = 100 µA
0.2
0.2
Input HIGH Voltage
Input LOW Voltage
2.0
1.7
VDD + 0.3
VDD + 0.3
0.8
VIL
–0.3
–0.3
–5
0.7
IX
Input Load Current
GND < VIN < VDDQ
5
Note
11. All voltages refer to V (GND).
SS
Document #: 001-15031 Rev. *C
Page 16 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Table 6. Identification Register Definitions
CY7C1470BV33
Instruction Field
CY7C1472BV33
(4M x 18)
CY7C1474BV33
Description
(1M x 72)
(2M x 36)
Revision Number (31:29)
Device Depth (28:24)[12]
000
000
000
Describes the version number
Reserved for internal use
01011
001000
01011
001000
01011
001000
Architecture/Memory
Type(23:18)
Defines memory type and archi-
tecture
Bus Width/Density(17:12)
100100
010100
110100
Defines width and density
Cypress JEDEC ID Code
(11:1)
00000110100
00000110100
00000110100
Enables unique identification of
SRAM vendor
ID Register Presence
Indicator (0)
1
1
1
Indicates the presence of an ID
register
Table 7. Scan Register Sizes
Register Name
Bit Size (x36)
Bit Size (x18)
Bit Size (x72)
Instruction
Bypass
ID
3
1
3
1
3
1
32
71
-
32
52
-
32
-
Boundary Scan Order – 165 FBGA
Boundary Scan Order – 209 FBGA
110
Table 8. Identification Codes
Instruction
EXTEST
Code
Description
000
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM outputs to High-Z state. This instruction is not 1149.1 compliant.
IDCODE
001
010
Loads the ID register with the vendor ID code and places the register between TDI
and TDO. This operation does not affect SRAM operations.
SAMPLE Z
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a High-Z state.
RESERVED
011
100
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Does not affect SRAM operation. This instruction does not implement 1149.1 preload
function and is therefore not 1149.1 compliant.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
Note
12. Bit #24 is “1” in the ID Register Definitions for both 2.5V and 3.3V versions of this device.
Document #: 001-15031 Rev. *C
Page 17 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Table 9. Boundary Scan Exit Order (2M x 36)
Bit #
1
165-Ball ID
C1
Bit #
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
165-Ball ID
R3
Bit #
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
165-Ball ID
J11
Bit #
61
62
63
64
65
66
67
68
69
70
71
165-Ball ID
B7
B6
A6
B5
A5
A4
B4
B3
A3
A2
B2
2
D1
P2
K10
J10
3
E1
R4
4
D2
P6
H11
G11
F11
E11
D10
D11
C11
G10
F10
E10
A9
5
E2
R6
6
F1
R8
7
G1
F2
P3
8
P4
9
G2
J1
P8
10
11
12
13
14
15
16
17
18
19
20
P9
K1
P10
R9
L1
J2
R10
R11
N11
M11
L11
M10
L10
K11
M1
N1
B9
K2
A10
B10
A8
L2
M2
R1
B8
R2
A7
Table 10. Boundary Scan Exit Order (4M x 18)
Bit #
1
165-Ball ID
Bit #
14
15
16
17
18
19
20
21
22
23
24
25
26
165-Ball ID
R4
Bit #
27
28
29
30
31
32
33
34
35
36
37
38
39
165-Ball ID
L10
Bit #
40
41
42
43
44
45
46
47
48
49
50
51
52
165-Ball ID
B10
A8
D2
E2
F2
G2
J1
2
P6
K10
J10
3
R6
B8
4
R8
H11
G11
F11
A7
5
P3
B7
6
K1
L1
P4
B6
7
P8
E11
A6
8
M1
N1
R1
R2
R3
P2
P9
D11
C11
A11
B5
9
P10
R9
A4
10
11
12
13
B3
R10
R11
M10
A9
A3
B9
A2
A10
B2
Document #: 001-15031 Rev. *C
Page 18 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Boundary Scan Exit Order (1M x 72)
Bit #
1
209-Ball ID
A1
Bit #
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
209-Ball ID
T1
Bit #
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
209-Ball ID
U10
T11
Bit #
85
209-Ball ID
B11
B10
A11
A10
A7
2
A2
T2
86
3
B1
U1
T10
R11
R10
P11
P10
N11
N10
M11
M10
L11
87
4
B2
U2
88
5
C1
C2
D1
D2
E1
V1
89
6
V2
90
A5
7
W1
W2
T6
91
A9
8
92
U8
9
93
A6
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
E2
V3
94
D6
F1
V4
95
K6
F2
U4
96
B6
G1
G2
H1
H2
J1
W5
V6
L10
97
K3
P6
98
A8
W6
V5
J11
99
B4
J10
100
101
102
103
104
105
106
107
108
109
110
B3
U5
H11
H10
G11
G10
F11
C3
J2
U6
C4
L1
W7
V7
C8
L2
C9
M1
M2
N1
N2
P1
U7
B9
V8
F10
E10
E11
D11
D10
C11
C10
B8
V9
A4
W11
W10
V11
V10
U11
C6
B7
P2
A3
R2
R1
Document #: 001-15031 Rev. *C
Page 19 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
DC Input Voltage ................................... –0.5V to VDD + 0.5V
Current into Outputs (LOW) ........................................ 20 mA
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Static Discharge Voltage.......................................... > 2001V
(MIL-STD-883, Method 3015)
Storage Temperature ................................. –65°C to +150°C
Latch Up Current................................................... > 200 mA
Ambient Temperature with
Power Applied ............................................ –55°C to +125°C
Operating Range
Supply Voltage on VDD Relative to GND........–0.5V to +4.6V
Supply Voltage on VDDQ Relative to GND.......–0.5V to +VDD
DC to Outputs in Tri-State....................–0.5V to VDDQ + 0.5V
Ambient
Range
VDD
VDDQ
Temperature
Commercial 0°C to +70°C
Industrial –40°C to +85°C
3.3V
–5%/+10%
2.5V – 5%
to VDD
Electrical Characteristics
Over the Operating Range[13, 14]
Parameter
VDD
Description
Power Supply Voltage
IO Supply Voltage
Test Conditions
Min
Max
3.6
Unit
V
3.135
3.135
2.375
2.4
VDDQ
VOH
VOL
VIH
VIL
For 3.3V IO
For 2.5V IO
VDD
2.625
V
V
Output HIGH Voltage
Output LOW Voltage
For 3.3V IO, IOH = −4.0 mA
For 2.5V IO, IOH= −1.0 mA
For 3.3V IO, IOL= 8.0 mA
For 2.5V IO, IOL= 1.0 mA
V
2.0
V
0.4
0.4
V
V
Input HIGH Voltage[13] For 3.3V IO
2.0
1.7
VDD + 0.3V
V
V
For 2.5V IO
VDD + 0.3V
Input LOW Voltage[13] For 3.3V IO
For 2.5V IO
–0.3
–0.3
–5
0.8
0.7
5
V
V
IX
Input Leakage Current GND ≤ VI ≤ VDDQ
except ZZ and MODE
μA
Input Current of MODE Input = VSS
Input = VDD
–30
–5
μA
μA
5
Input Current of ZZ
Input = VSS
Input = VDD
μA
30
5
μA
IOZ
Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled
–5
μA
[15]
IDD
VDD Operating Supply VDD = Max., IOUT = 0 mA,
f = fMAX = 1/tCYC
4.0-ns cycle, 250 MHz
5.0-ns cycle, 200 MHz
6.0-ns cycle, 167 MHz
500
500
450
245
245
245
120
mA
mA
mA
mA
mA
mA
mA
ISB1
Automatic CE
Power Down
Current—TTL Inputs
Max. VDD, Device Deselected, 4.0-ns cycle, 250 MHz
VIN ≥ VIH or VIN ≤ VIL,
5.0-ns cycle, 200 MHz
f = fMAX = 1/tCYC
6.0-ns cycle, 167 MHz
ISB2
Automatic CE
Power Down
Current—CMOS Inputs f = 0
Max. VDD, Device Deselected, All speed grades
VIN ≤ 0.3V or VIN > VDDQ − 0.3V,
Notes
13. Overshoot: V (AC) < V +1.5V (pulse width less than t
/2). Undershoot: V (AC)> –2V (pulse width less than t
/2).
IH
DD
CYC
IL
CYC
.
14. T
: assumes a linear ramp from 0V to V (min.) within 200 ms. During this time V < V and V
< V
Power-up
DD
IH
DD
DDQ DD
15. The operation current is calculated with 50% read cycle and 50% write cycle.
Document #: 001-15031 Rev. *C
Page 20 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Electrical Characteristics
Over the Operating Range[13, 14] (continued)
Parameter
ISB3
Description
Automatic CE
Power Down
Test Conditions
Min
Max
245
245
245
135
Unit
mA
mA
mA
mA
Max. VDD, Device Deselected, 4.0-ns cycle, 250 MHz
VIN ≤ 0.3V or VIN > VDDQ − 0.3V,
5.0-ns cycle, 200 MHz
Current—CMOS Inputs f = fMAX = 1/tCYC
6.0-ns cycle, 167 MHz
ISB4
Automatic CE
Max. VDD, Device Deselected, All speed grades
Power Down
Current—TTL Inputs
VIN ≥ VIH or VIN ≤ VIL, f = 0
Capacitance
Tested initially and after any design or process changes that may affect these parameters.
100 TQFP 165 FBGA 209 FBGA
Parameter
Description
Test Conditions
Unit
Max
Max
Max
CADDRESS
CDATA
CCTRL
CCLK
Address Input Capacitance
Data Input Capacitance
Control Input Capacitance
Clock Input Capacitance
Input/Output Capacitance
TA = 25°C, f = 1 MHz,
6
5
8
6
5
6
5
8
6
5
6
5
8
6
5
pF
pF
pF
pF
pF
VDD = 3.3V
VDDQ = 2.5V
CIO
Thermal Resistance
Tested initially and after any design or process changes that may affect these parameters.
100 TQFP
Package
165 FBGA 209 FBGA
Parameters
Description
Test Conditions
Unit
Package
Package
ΘJA
Thermal Resistance
(Junction to Ambient)
Test conditions follow standard
test methods and procedures for
measuring thermal impedance,
per EIA/JESD51.
24.63
16.3
15.2
°C/W
ΘJC
Thermal Resistance
(Junction to Case)
2.28
2.1
1.7
°C/W
AC Test Loads and Waveforms
3.3V IO Test Load
R = 317Ω
3.3V
OUTPUT
ALL INPUT PULSES
90%
VDDQ
OUTPUT
R = 50Ω
90%
10%
Z = 50Ω
0
10%
L
GND
5 pF
R = 351Ω
≤ 1 ns
≤ 1 ns
V = 1.5V
L
INCLUDING
JIG AND
SCOPE
(c)
(a)
(b)
2.5V IO Test Load
R = 1667Ω
2.5V
OUTPUT
R = 50Ω
OUTPUT
ALL INPUT PULSES
90%
VDDQ
GND
90%
10%
Z = 50Ω
0
10%
L
5 pF
R = 1538Ω
≤ 1 ns
≤ 1 ns
V = 1.25V
L
INCLUDING
JIG AND
SCOPE
(c)
(a)
(b)
Document #: 001-15031 Rev. *C
Page 21 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Switching Characteristics
Over the Operating Range. Timing reference is 1.5V when VDDQ = 3.3V and is 1.25V when VDDQ = 2.5V. Test conditions shown in
(a) of “AC Test Loads and Waveforms” on page 21 unless otherwise noted.
–250
–200
Max
–167
Parameter
Description
Unit
Min
Max
Min
Min
Max
[16]
tPower
VCC (typical) to the First Access Read or Write
1
1
1
ms
Clock
tCYC
Clock Cycle Time
Maximum Operating Frequency
Clock HIGH
4.0
5.0
6.0
ns
MHz
ns
FMAX
tCH
250
200
167
2.0
2.0
2.0
2.0
2.2
2.2
tCL
Clock LOW
ns
Output Times
tCO
Data Output Valid After CLK Rise
OE LOW to Output Valid
3.0
3.0
3.0
3.0
3.4
3.4
ns
ns
ns
ns
ns
ns
ns
tOEV
tDOH
Data Output Hold After CLK Rise
Clock to High-Z[17, 18, 19]
Clock to Low-Z[17, 18, 19]
OE HIGH to Output High-Z[17, 18, 19]
OE LOW to Output Low-Z[17, 18, 19]
1.3
1.3
0
1.3
1.3
0
1.5
1.5
0
tCHZ
3.0
3.0
3.0
3.0
3.4
3.4
tCLZ
tEOHZ
tEOLZ
Setup Times
tAS
Address Setup Before CLK Rise
Data Input Setup Before CLK Rise
CEN Setup Before CLK Rise
WE, BWx Setup Before CLK Rise
ADV/LD Setup Before CLK Rise
Chip Select Setup
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
ns
ns
ns
ns
ns
ns
tDS
tCENS
tWES
tALS
tCES
Hold Times
tAH
Address Hold After CLK Rise
Data Input Hold After CLK Rise
CEN Hold After CLK Rise
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
ns
ns
ns
ns
tDH
tCENH
tWEH
WE, BWx Hold After CLK Rise
ADV/LD Hold after CLK Rise
Chip Select Hold After CLK Rise
tALH
tCEH
Notes
16. This part has an internal voltage regulator; t
is the time power is supplied above V minimum initially, before a read or write operation can be initiated.
DD
power
17. t
, t
, t
, and t
are specified with AC test conditions shown in (b) of “AC Test Loads and Waveforms” on page 21. Transition is measured ±200 mV
CHZ CLZ EOLZ
EOHZ
from steady-state voltage.
18. At any voltage and temperature, t
is less than t
and t
is less than t
to eliminate bus contention between SRAMs when sharing the same data
CLZ
EOHZ
EOLZ
CHZ
bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to
achieve High-Z before Low-Z under the same system conditions.
19. This parameter is sampled and not 100% tested.
Document #: 001-15031 Rev. *C
Page 22 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Switching Waveforms
Figure 5 shows read-write timing waveform.[20, 21, 22]
Figure 5. Read/Write Timing
1
2
3
4
5
6
7
8
9
10
t
CYC
t
CLK
CEN
t
t
t
CENS
CENH
CL
CH
t
t
CES
CEH
CE
ADV/LD
WE
BW
x
A1
A2
A4
CO
A3
A5
A6
A7
ADDRESS
t
t
t
t
DS
DH
t
t
t
DOH
OEV
CLZ
CHZ
t
t
AS
AH
Data
D(A1)
D(A2)
D(A2+1)
Q(A3)
Q(A4)
Q(A4+1)
D(A5)
Q(A6)
In-Out (DQ)
t
OEHZ
t
DOH
t
OELZ
OE
WRITE
D(A1)
WRITE
D(A2)
BURST
WRITE
READ
Q(A3)
READ
Q(A4)
BURST
READ
WRITE
D(A5)
READ
Q(A6)
WRITE
D(A7)
DESELECT
D(A2+1)
Q(A4+1)
DON’T CARE
UNDEFINED
Notes
20. For this waveform ZZ is tied LOW.
21. When CE is LOW, CE is LOW, CE is HIGH, and CE is LOW. When CE is HIGH, CE is HIGH, CE is LOW or CE is HIGH.
1
2
3
1
2
3
22. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1= Interleaved). Burst operations are optional.
Document #: 001-15031 Rev. *C
Page 23 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Switching Waveforms (continued)
Figure 6 shows NOP, STALL and DESELECT Cycles waveform.[20, 21, 23]
Figure 6. NOP, STALL and DESELECT Cycles
1
2
3
4
5
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BWx
A1
A2
A3
A4
A5
ADDRESS
t
CHZ
D(A4)
D(A1)
Q(A2)
Q(A3)
Q(A5)
Data
In-Out (DQ)
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
STALL
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
DON’T CARE
UNDEFINED
Figure 7 shows ZZ Mode timing waveform.[24, 25]
Figure 7. ZZ Mode Timing
CLK
t
t
ZZ
ZZREC
ZZ
t
ZZI
I
SUPPLY
I
DDZZ
t
RZZI
ALL INPUTS
(except ZZ)
DESELECT or READ Only
Outputs (Q)
High-Z
DON’T CARE
Notes
23. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A Write is not performed during this cycle.
24. Device must be deselected when entering ZZ mode. See “Truth Table” on page 10 for all possible signal conditions to deselect the device.
25. IOs are in High-Z when exiting ZZ sleep mode.
Document #: 001-15031 Rev. *C
Page 24 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Ordering Information
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or visit
www.cypress.com for actual products offered.
Speed
(MHz)
Package
Diagram
Operating
Range
Part and Package Type
Ordering Code
167 CY7C1470BV33-167AXC 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-free
CY7C1472BV33-167AXC
Commercial
CY7C1470BV33-167BZC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1472BV33-167BZC
CY7C1470BV33-167BZXC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-free
CY7C1472BV33-167BZXC
CY7C1474BV33-167BGC 51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
CY7C1474BV33-167BGXC
CY7C1470BV33-167AXI
CY7C1472BV33-167AXI
CY7C1470BV33-167BZI
CY7C1472BV33-167BZI
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-free
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-free
lndustrial
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1470BV33-167BZXI 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-free
CY7C1472BV33-167BZXI
CY7C1474BV33-167BGI
CY7C1474BV33-167BGXI
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-free
200 CY7C1470BV33-200AXC 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-free
CY7C1472BV33-200AXC
Commercial
CY7C1470BV33-200BZC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1472BV33-200BZC
CY7C1470BV33-200BZXC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-free
CY7C1472BV33-200BZXC
CY7C1474BV33-200BGC 51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
CY7C1474BV33-200BGXC
CY7C1470BV33-200AXI
CY7C1472BV33-200AXI
CY7C1470BV33-200BZI
CY7C1472BV33-200BZI
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-free
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-free
lndustrial
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1470BV33-200BZXI 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-free
CY7C1472BV33-200BZXI
CY7C1474BV33-200BGI
CY7C1474BV33-200BGXI
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-free
Document #: 001-15031 Rev. *C
Page 25 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Ordering Information (continued)
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or visit
www.cypress.com for actual products offered.
Speed
(MHz)
Package
Diagram
Operating
Range
Part and Package Type
Ordering Code
250 CY7C1470BV33-250AXC 51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-free
CY7C1472BV33-250AXC
Commercial
CY7C1470BV33-250BZC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1472BV33-250BZC
CY7C1470BV33-250BZXC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-free
CY7C1472BV33-250BZXC
CY7C1474BV33-250BGC 51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
CY7C1474BV33-250BGXC
CY7C1470BV33-250AXI
CY7C1472BV33-250AXI
CY7C1470BV33-250BZI
CY7C1472BV33-250BZI
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-free
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-free
Industrial
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1470BV33-250BZXI 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-free
CY7C1472BV33-250BZXI
CY7C1474BV33-250BGI
CY7C1474BV33-250BGXI
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-free
Document #: 001-15031 Rev. *C
Page 26 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Package Diagrams
Figure 8. 100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm), 51-85050
16.00 0.20
14.00 0.10
1.40 0.05
100
81
80
1
0.30 0.08
0.65
TYP.
12° 1°
(8X)
SEE DETAIL
A
30
51
31
50
0.20 MAX.
1.60 MAX.
R 0.08 MIN.
0.20 MAX.
0° MIN.
SEATING PLANE
STAND-OFF
0.05 MIN.
0.15 MAX.
NOTE:
1. JEDEC STD REF MS-026
0.25
GAUGE PLANE
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
R 0.08 MIN.
0.20 MAX.
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
3. DIMENSIONS IN MILLIMETERS
0°-7°
0.60 0.15
1.00 REF.
0.20 MIN.
51-85050-*B
DETAIL
A
Document #: 001-15031 Rev. *C
Page 27 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Package Diagrams (continued)
Figure 9. 165-Ball FBGA (15 x 17 x 1.4 mm), 51-85165
PIN 1 CORNER
BOTTOM VIEW
TOP VIEW
Ø0.05 M C
PIN 1 CORNER
Ø0.25 M C A B
Ø0.45 0.05(165X)
1
2
3
4
5
6
7
8
9
10
11
11 10
9
8
7
6
5
4
3
2
1
A
B
A
B
C
D
C
D
E
E
F
F
G
G
H
J
H
J
K
K
L
L
M
M
N
P
R
N
P
R
A
1.00
5.00
10.00
B
15.00 0.10
0.15(4X)
SEATING PLANE
C
51-85165-*A
Document #: 001-15031 Rev. *C
Page 28 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Package Diagrams (continued)
Figure 10. 209-Ball FBGA (14 x 22 x 1.76 mm), 51-85167
51-85167-**
Document #: 001-15031 Rev. *C
Page 29 of 30
[+] Feedback
CY7C1470BV33
CY7C1472BV33, CY7C1474BV33
Document History Page
Document Title: CY7C1470BV33/CY7C1472BV33/CY7C1474BV33, 72-Mbit (2M x 36/4M x 18/1M x 72) Pipelined SRAM
with NoBL™ Architecture
Document Number: 001-15031
Orig. of
Change
REV.
ECN No. Issue Date
Description of Change
**
1032642
1897447
2082487
2159486
See ECN VKN/KKVTMP New Data Sheet
*A
*B
*C
See ECN
See ECN
See ECN
VKN/AESA
VKN
Added footnote 15 related to IDD
Converted from preliminary to final
VKN/PYRS
Minor Change-Moved to the external web
© Cypress Semiconductor Corporation, 2007-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used
for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use
as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support
systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 001-15031 Rev. *C
Revised February 29, 2008
Page 30 of 30
NoBL and No Bus Latency are trademarks of Cypress Semiconductor Corporation. ZBT is a trademark of Integrated Device Technology, Inc. All products and company names mentioned in this
document may be the trademarks of their respective holders.
[+] Feedback
相关型号:
CY7C1470BV33-250BZC
72-Mbit (2M x 36/4M x 18/1M x 72) Pipelined SRAM with NoBL⑩ Architecture
CYPRESS
CY7C1470BV33-250BZI
72-Mbit (2M x 36/4M x 18/1M x 72) Pipelined SRAM with NoBL⑩ Architecture
CYPRESS
CY7C1470BV33-250BZXC
72-Mbit (2M x 36/4M x 18/1M x 72) Pipelined SRAM with NoBL⑩ Architecture
CYPRESS
CY7C1470BV33-250BZXI
72-Mbit (2M x 36/4M x 18/1M x 72) Pipelined SRAM with NoBL⑩ Architecture
CYPRESS
CY7C1470BV33_13
72-Mbit (2 M x 36/4 M à 18/1 M x 72) Pipelined SRAM with NoBL⢠Architecture
CYPRESS
CY7C1470V25-167AXC
2MX36 ZBT SRAM, 3.4ns, PQFP100, 14 X 20 MM, 1.40 MM HEIGHT, LEAD FREE, PLASTIC, MS-026, TQFP-100
ROCHESTER
CY7C1470V25-167BGC
ZBT SRAM, 2MX36, 3.4ns, CMOS, PBGA119, 14 X 22 MM, 2.40 MM HEIGHT, PLASTIC, BGA-119
CYPRESS
©2020 ICPDF网 联系我们和版权申明