CY7B9911 [CYPRESS]
High-Speed Low-Voltage Programmable Skew Clock Buffer LV-PSCB; 高速低电压可编程偏移时钟缓冲器LV- PSCB
| 型号： | CY7B9911 |
| 厂家： | 
CYPRESS |
| 描述： | High-Speed Low-Voltage Programmable Skew Clock Buffer LV-PSCB |
| 文件： | 总11页 (文件大小：226K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CY7B9911V
3.3V RoboClock+
High-Speed Low-Voltage Programmable Skew Clock Buffer
(LV-PSCB)
selectable control over system clock functions. These multiple-
Features
output clock drivers provide the system integrator with func-
tions necessary to optimize the timing of high-performance
computer systems. Eight individual drivers, arranged as four
pairs of user-controllable outputs, can each drive terminated
transmission lines with impedances as low as 50Ω while deliv-
ering minimal and specified output skews and full-swing logic levels
(LVTTL).
• All output pair skew <100 ps typical (250 max.)
• 3.75- to 110-MHz output operation
• User-selectable output functions
— Selectable skew to 18 ns
— Inverted and non-inverted
1
1
Each output can be hardwired to one of nine delay or function
configurations. Delay increments of 0.7 to 1.5 ns are deter-
mined by the operating frequency with outputs able to skew up
to ±6 time units from their nominal “zero” skew position. The com-
pletely integrated PLL allows external load and transmission
line delay effects to be canceled. When this “zero delay” capa-
bility of the LVPSCB is combined with the selectable output
skew functions, the user can create output-to-output delays of
up to ±12 time units.
— Operation at
and
input frequency
⁄
4
⁄
2
— Operation at 2x and 4x input frequency (input as low
as 3.75 MHz)
• Zero input-to-output delay
• 50% duty-cycle outputs
LVTTL outputs drive 50 terminated lines
Operates from a single 3.3V supply
• Low operating current
•
•
Ω
Divide-by-two and divide-by-four output functions are provided
for additional flexibility in designing complex clock systems.
When combined with the internal PLL, these divide functions
allow distribution of a low-frequency clock that can be multi-
plied by two or four at the clock destination. This facility mini-
mizes clock distribution difficulty while allowing maximum sys-
tem clock speed and flexibility.
• 32-pin PLCC package
• Jitter < 200 ps peak-to-peak (< 25 ps RMS)
Functional Description
The CY7B9911V 3.3V RoboClock+ High-Speed Low-Voltage
Programmable Skew Clock Buffer (LVPSCB) offers user-
Logic Block Diagram
Pin Configuration
TEST
PLCC
PHASE
FREQ
DET
FB
VCO AND
TIME UNIT
GENERATOR
FILTER
REF
4
3
2
1
32 31 30
29
FS
2F0
GND
1F1
1F0
5
6
3F1
4F0
28
27
4Q0
4Q1
4F0
4F1
4F1
7
8
9
SELECT
INPUTS
(THREE
LEVEL)
V
26
25
24
23
CCQ
CY7B9911V
V
CCN
SKEW
SELECT
MATRIX
V
CCN
3Q0
3Q1
3F0
3F1
4Q1
10
1Q0
1Q1
GND
GND
4Q0
GND
GND
11
12
22
21
2Q0
2Q1
2F0
2F1
13
14 15 16 17 18 19 20
1Q0
1Q1
1F0
1F1
7B9911V–2
7B9911V–1
Cypress Semiconductor Corporation
•
3901 North First Street
•
San Jose
•
CA 95134
•
408-943-2600
December 1, 1999
CY7B9911V
3.3V RoboClock+
Pin Definitions
Signal Name
REF
I/O
Description
I
Reference frequency input. This input supplies the frequency and timing against which all functional
variation is measured.
FB
I
PLL feedback input (typically connected to one of the eight outputs).
Three-level frequency range select. See Table 1.
Three-level function select inputs for output pair 1 (1Q0, 1Q1). See Table 2.
Three-level function select inputs for output pair 2 (2Q0, 2Q1). See Table 2.
Three-level function select inputs for output pair 3 (3Q0, 3Q1). See Table 2.
Three-level function select inputs for output pair 4 (4Q0, 4Q1). See Table 2.
Three-level select. See test mode section under the block diagram descriptions.
Output pair 1. See Table 2.
FS
I
1F0, 1F1
2F0, 2F1
3F0, 3F1
4F0, 4F1
TEST
I
I
I
I
I
1Q0, 1Q1
2Q0, 2Q1
3Q0, 3Q1
4Q0, 4Q1
O
O
Output pair 2. See Table 2.
O
Output pair 3. See Table 2.
O
Output pair 4. See Table 2.
V
V
PWR
PWR
PWR
Power supply for output drivers.
CCN
CCQ
Power supply for internal circuitry.
GND
Ground.
Skew Select Matrix
Block Diagram Description
The skew select matrix is comprised of four independent sec-
tions. Each section has two low-skew, high-fanout drivers
(xQ0, xQ1), and two corresponding three-level function select
(xF0, xF1) inputs. Table 2 below shows the nine possible out-
put functions for each section as determined by the function
select inputs. All times are measured with respect to the REF
input assuming that the output connected to the FB input has
Phase Frequency Detector and Filter
These two blocks accept inputs from the Reference Frequency
(REF) input and the Feedback (FB) input and generate correc-
tion information to control the frequency of the Voltage-
Controlled Oscillator (VCO). These blocks, along with the
VCO, form a Phase-Locked Loop (PLL) that tracks the incom-
ing REF signal.
0t selected.
U
[1]
VCO and Time Unit Generator
Table 2. Programmable Skew Configurations
The VCO accepts analog control inputs from the PLL filter
block and generates a frequency that is used by the time unit
generator to create discrete time units that are selected in the
skew select matrix. The operational range of the VCO is deter-
Function Selects
Output Functions
1F1, 2F1, 1F0, 2F0, 1Q0,1Q1,
3F1, 4F1 3F0, 4F0 2Q0, 2Q1 3Q0, 3Q1 4Q0, 4Q1
mined by the FS control pin. The time unit (t ) is determined
by the operating frequency of the device and the level of the
FS pin as shown in Table 1.
LOW
LOW
LOW
MID
LOW
MID
–4t
–3t
–2t
–1t
0t
Divide by 2 Divide by 2
U
U
U
U
U
–6t
–4t
–2t
0t
–6t
–4t
–2t
0t
U
U
U
U
U
U
HIGH
LOW
MID
[1]
Table 1. Frequency Range Select and t Calculation
U
f
(MHz)
MID
NOM
U
U
U
1
tU
=
-----------------------
NOM × N
Approximate
f
MID
HIGH
LOW
MID
+1t
+2t
+3t
+4t
+2t
+4t
+6t
+2t
+4t
+6t
U
U
U
U
U
U
U
U
U
U
Frequency(MHz)At
[2, 3]
FS
Min. Max.
where N =
Which t = 1.0 ns
HIGH
HIGH
HIGH
U
LOW
MID
15
25
40
30
50
44
26
16
22.7
38.5
62.5
HIGH
Divide by 4 Inverted
HIGH
110
Notes:
1. For all three-state inputs, HIGH indicates a connection to VCC, LOW indicates a connection to GND, and MID indicates an open connection. Internal termination
circuitry holds an unconnected input to VCC/2.
2. The level to be set on FS is determined by the “normal” operating frequency (fNOM) of the VCO and Time Unit Generator (see Logic Block Diagram). Nominal
frequency (fNOM) always appears at 1Q0 and the other outputs when they are operated in their undivided modes (see Table 2). The frequency appearing at the
REF and FB inputs will be fNOM when the output connected to FB is undivided. The frequency of the REF and FB inputs will be fNOM/2 or fNOM/4 when the part
is configured for a frequency multiplication by using a divided output as the FB input.
3. When the FS pin is selected HIGH, the REF input must not transition upon power-up until VCC has reached 2.8V.
2
CY7B9911V
3.3V RoboClock+
FBInput
REFInput
1Fx
2Fx
3Fx
4Fx
(N/A)
LM
– 6t
– 4t
– 3t
U
U
U
LL
LH
LM
(N/A)
LH
ML
ML
– 2t
– 1t
U
(N/A)
U
MM
MH
HL
MM
(N/A)
MH
0t
U
+1t
+2t
+3t
U
U
U
HM
(N/A)
HH
HL
HM
+4t
+6t
U
(N/A)
(N/A)
(N/A)
U
LL/HH
HH
DIVIDED
INVERT
7B9911V–3
[4]
Figure 1. Typical Outputs with FB Connected to a Zero-Skew Output
Test Mode
Maximum Ratings
The TEST input is a three-level input. In normal system oper-
ation, this pin is connected to ground, allowing the
CY7B9911V to operate as explained briefly above (for testing
purposes, any of the three-level inputs can have a removable
jumper to ground, or be tied LOW through a 100Ω resistor. This
will allow an external tester to change the state of these pins.)
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Supply Voltage to Ground Potential................–0.5V to +7.0V
DC Input Voltage ............................................–0.5V to +7.0V
Output Current into Outputs (LOW)............................. 64 mA
If the TEST input is forced to its MID or HIGH state, the device
will operate with its internal phase locked loop disconnected,
and input levels supplied to REF will directly control all outputs.
Relative output to output functions are the same as in normal
mode.
Static Discharge Voltage ........................................... >2001V
(per MIL-STD-883, Method 3015)
In contrast with normal operation (TEST tied LOW). All outputs
will function based only on the connection of their own function
select inputs (xF0 and xF1) and the waveform characteristics
of the REF input.
Latch-Up Current..................................................... >200 mA
Operating Range
Ambient
Temperature
Range
V
CC
Commercial
0°C to +70°C
3.3V ± 10%
Note:
4. FB connected to an output selected for “zero” skew (i.e., xF1 = xF0 =
MID).
3
CY7B9911V
3.3V RoboClock+
[5]
Electrical Characteristics Over the Operating Range
CY7B9911V
Parameter
Description
Output HIGH Voltage
Output LOW Voltage
Test Conditions
= Min., I = –18 mA
Min.
Max.
Unit
V
V
V
V
2.4
OH
CC
CC
OH
V
= Min., I = 35 mA
0.45
V
OL
OL
V
Input HIGH Voltage
(REF and FB inputs only)
2.0
–0.5
V
V
IH
CC
V
V
V
V
Input LOW Voltage
(REF and FB inputs only)
0.8
V
V
IL
Three-Level Input HIGH
Voltage (Test, FS, xFn)
Min. ≤ V ≤ Max.
0.87 * V
0.47 * V
0.0
V
CC
IHH
IMM
ILL
CC
CC
[6]
Three-Level Input MID
Voltage (Test, FS, xFn)
Min. ≤ V ≤ Max.
0.53 * V
V
CC
CC
CC
[6]
Three-Level Input LOW
Voltage (Test, FS, xFn)
Min. ≤ V ≤ Max.
0.13 * V
20
V
CC
CC
[6]
I
I
I
I
I
Input HIGH Leakage Current
(REF and FB inputs only)
V
V
V
V
V
= Max., V = Max.
µA
µA
µA
µA
µA
IH
CC
CC
IN
Input LOW Leakage Current
(REF and FB inputs only)
= Max., V = 0.4V
–20
–50
IL
IN
Input HIGH Current
(Test, FS, xFn)
= V
200
50
IHH
IMM
ILL
IN
IN
IN
CC
Input MID Current
(Test, FS, xFn)
= V /2
CC
Input LOW Current
(Test, FS, xFn)
= GND
–200
[7]
I
I
Short Circuit Current
V
V
= MAX, V = GND (25° only)
OUT
–200
95
mA
mA
OS
CC
Operating Current Used by
Internal Circuitry
= V
= Max., Com’l
CCQ
CCQ
CCN
All Input Selects Open
Mil/Ind
100
19
I
Output Buffer Current per
V
= V = Max.,
mA
CCN
CCN
CCQ
[8]
Output Pair
I
= 0 mA
OUT
Input Selects Open, f
MAX
PD
Power Dissipation per
Output Pair
V
= V
= 0 mA
= Max.,
CCQ
104
mW
CCN
[9]
I
OUT
Input Selects Open, f
MAX
Capacitance[10]
Parameter
Description
Test Conditions
Max.
Unit
C
Input Capacitance
T = 25°C, f = 1 MHz, V = 3.3V
10
pF
IN
A
CC
Notes:
5. See the last page of this specification for Group A subgroup testing information.
6. These inputs are normally wired to VCC, GND, or left unconnected (actual threshold voltages vary as a percentage of VCC). Internal termination resistors hold
unconnected inputs at VCC/2. If these inputs are switched, the function and timing of the outputs may glitch and the PLL may require an additional tLOCK time
before all data sheet limits are achieved.
7. CY7B9911V should be tested one output at a time, output shorted for less than one second, less than 10% duty cycle. Room temperature only.
8. Total output current per output pair can be approximated by the following expression that includes device current plus load current:
CY7B9911V:ICCN = [(4 + 0.11F) + [[((835 –3F)/Z) + (.0022FC)]N] x 1.1
Where
F = frequency in MHz
C = capacitive load in pF
Z = line impedance in ohms
N = number of loaded outputs; 0, 1, or 2
FC = F < C
9. Total power dissipation per output pair can be approximated by the following expression that includes device power dissipation plus power dissipation due to
the load circuit:
PD = [(22 + 0.61F) + [[(1550 + 2.7F)/Z) + (.0125FC)]N] x 1.1
See note 8 for variable definition.
10. Applies to REF and FB inputs only. Tested initially and after any design or process changes that may affect these parameters.
4
CY7B9911V
3.3V RoboClock+
AC Test Loads and Waveforms
VCC
3.0V
2.0V
=1.5V
0.8V
0.0V
2.0V
th
0.8V
R1=100
R2=100
R1
R2
V
th
V =1.5V
C = 30 pF
L
C
(Includes fixture and probe capacitance)
L
1ns
≤
1ns
≤
7B9911V–4
7B9911V–5
TTL ACTest Load
TTL Input Test Waveform
[2, 11]
Switching Characteristics Over the Operating Range
CY7B9911V–5
Typ.
Parameter
Description
FS = LOW
Min.
15
Max.
30
Unit
[1, 2]
[1, 2]
f
Operating Clock
Frequency in MHz
MHz
NOM
FS = MID
25
50
[1, 2 , 3]
FS = HIGH
40
110
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
REF Pulse Width HIGH
5.0
5.0
ns
ns
RPWH
RPWL
U
REF Pulse Width LOW
Programmable Skew Unit
See Table 1
[13, 14]
Zero Output Matched-Pair Skew (XQ0, XQ1)
0.1
0.25
0.6
0.5
0.5
0.5
0.25
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
ps
ps
SKEWPR
SKEW0
SKEW1
SKEW2
SKEW3
SKEW4
DEV
[13, 15]
Zero Output Skew (All Outputs)
0.5
0.7
1.0
0.7
1.0
1.25
+0.5
+1.0
2.5
3
[13, 17]
Output Skew (Rise-Rise, Fall-Fall, Same Class Outputs)
[13, 17]
Output Skew (Rise-Fall, Nominal-Inverted, Divided-Divided)
[13, 17]
[13, 17]
Output Skew (Rise-Rise, Fall-Fall, Different Class Outputs)
Output Skew (Rise-Fall, Nominal-Divided, Divided-Inverted)
[12, 18]
Device-to-Device Skew
Propagation Delay, REF Rise to FB Rise
–0.5
–1.0
0.0
0.0
PD
[19]
Output Duty Cycle Variation
ODCV
PWH
[20]
Output HIGH Time Deviation from 50%
[20]
Output LOW Time Deviation from 50%
PWL
[20, 21]
Output Rise Time
0.15
0.15
1.0
1.0
1.5
1.5
0.5
25
ORISE
OFALL
LOCK
JR
[20, 21]
Output Fall Time
[22]
PLL Lock Time
[12]
Cycle-to-Cycle Output
Jitter
RMS
[12]
Peak-to-Peak
200
Notes:
11. Test measurement levels for the CY7B9911V are TTL levels (1.5V to 1.5V). Test conditionsassumesignaltransition timesof 2ns or less and output loading as shown
in the AC Test Loads and Waveforms unless otherwise specified.
12. Guaranteed by statistical correlation. Tested initially and after any design or process changes that may affect these parameters.
13. SKEW is defined as the time between the earliest and the latest output transition among all outputs for which the same tU delay has been selected when all are
loaded with 30 pF and terminated with 50Ω to VCC/2 (CY7B9911V).
14. tSKEWPR is defined as the skew between a pair of outputs (XQ0 and XQ1) when all eight outputs are selected for 0tU.
15. tSKEW0 is defined as the skew between outputs when they are selected for 0tU. Other outputs are divided or inverted but not shifted.
16. CL=0 pF. For CL=30 pF, tSKEW0=0.35 ns.
17. There are three classes of outputs: Nominal (multiple of tU delay), Inverted (4Q0 and 4Q1 only with 4F0 = 4F1 = HIGH), and Divided (3Qx and 4Qx only in Divide-by-
2 or Divide-by-4 mode).
18. tDEV is the output-to-output skew between any two devices operating under the same conditions (VCC ambient temperature, air flow, etc.)
19. tODCV is the deviation of the output from a 50% duty cycle. Output pulse width variations are included in tSKEW2 and tSKEW4 specifications.
20. Specified with outputs loaded with 30 pF for the CY7B9911V–5 and –7 devices. Devices are terminated through 50Ω to VCC/2.tPWH is measured at 2.0V. tPWL is
measured at 0.8V.
21. tORISE and tOFALL measured between 0.8V and 2.0V.
22. tLOCK is the time that is required before synchronization is achieved. This specification is valid only after VCC is stable and within normal operating limits. This parameter is
measured from the application of a new signal or frequency at REF or FB until tPD is within specified limits.
5
CY7B9911V
3.3V RoboClock+
[2, 11]
Switching Characteristics Over the Operating Range
(continued)
CY7B9911V–7
Typ.
Parameter
Description
FS = LOW
Min.
15
Max.
30
Unit
[1, 2]
f
Operating Clock
MHz
NOM
Frequency in MHz
[1, 2]
FS = MID
25
50
[1, 2 , 3]
FS = HIGH
40
110
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
REF Pulse Width HIGH
5.0
5.0
ns
ns
RPWH
RPWL
U
REF Pulse Width LOW
Programmable Skew Unit
See Table 1
[13, 14]
Zero Output Matched-Pair Skew (XQ0, XQ1)
0.1
0.3
0.6
1.0
0.7
1.2
0.25
0.75
1.0
1.5
1.2
1.7
1.65
+0.7
+1.2
3
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
ps
ps
SKEWPR
SKEW0
SKEW1
SKEW2
SKEW3
SKEW4
DEV
[13, 15]
Zero Output Skew (All Outputs)
[13, 17]
Output Skew (Rise-Rise, Fall-Fall, Same Class Outputs)
Output Skew (Rise-Fall, Nominal-Inverted, Divided-Divided)
[13, 17]
[13, 17]
[13, 17]
Output Skew (Rise-Rise, Fall-Fall, Different Class Outputs)
Output Skew (Rise-Fall, Nominal-Divided, Divided-Inverted)
[12, 18]
Device-to-Device Skew
Propagation Delay, REF Rise to FB Rise
–0.7
–1.2
0.0
0.0
PD
[19]
Output Duty Cycle Variation
ODCV
PWH
[20]
Output HIGH Time Deviation from 50%
[20]
Output LOW Time Deviation from 50%
3.5
2.5
2.5
0.5
25
PWL
[20, 21]
Output Rise Time
0.15
0.15
1.5
1.5
ORISE
OFALL
LOCK
JR
[20, 21]
Output Fall Time
[22]
PLL Lock Time
[12]
Cycle-to-Cycle Output
Jitter
RMS
[12]
Peak-to-Peak
200
6
CY7B9911V
3.3V RoboClock+
AC Timing Diagrams
t
t
RPWL
REF
t
RPWH
REF
t
t
ODCV
PD
t
ODCV
FB
Q
t
JR
t
t
t
t
SKEWPR,
SKEW0,1
SKEWPR,
SKEW0,1
OTHERQ
t
SKEW2
t
SKEW2
INVERTED Q
t
SKEW3,4
t
t
SKEW3,4
t
SKEW3,4
REF DIVIDED BY 2
REF DIVIDED BY 4
t
SKEW1,3, 4
SKEW2,4
7B9911V–8
7
CY7B9911V
3.3V RoboClock+
Operational Mode Descriptions
REF
LOAD
Z
Z
0
L1
L2
FB
SYSTEM
CLOCK
REF
FS
LOAD
LOAD
4Q0
4Q1
4F0
4F1
0
3Q0
3Q1
3F0
3F1
L3
L4
2F0
2F1
2Q0
2Q1
Z
0
1F0
1F1
1Q0
1Q1
LOAD
TEST
Z
0
LENGTH L1 = L2 = L3 = L4
7B9911V–9
Figure 2. Zero-Skew and/or Zero-Delay Clock Driver
Figure 2 shows the LVPSCB configured as a zero-skew clock
buffer. In this mode the CY7B9911V can be used as the basis
for a low-skew clock distribution tree. When all of the function
select inputs (xF0, xF1) are left open, the outputs are aligned
and may each drive a terminated transmission line to an inde-
pendent load. The FB input can be tied to any output in this
configuration and the operating frequency range is selected
with the FS pin. The low-skew specification, coupled with the
ability to drive terminated transmission lines (with impedances
as low as 50Ω), allows efficient printed circuit board design.
REF
LOAD
Z
0
L1
L2
FB
REF
FS
SYS-
TEM
CLOCK
LOAD
LOAD
4Q0
4Q1
4F0
4F1
Z
0
3Q0
3Q1
3F0
3F1
L3
L4
2F0
2F1
2Q0
2Q1
Z
0
1F0
1F1
1Q0
1Q1
LOAD
TEST
Z
0
LENGTH L1 = L2
L3 < L2 by 6 inches
L4 > L2 by 6 inches
7B9911V–10
Figure 3. Programmable-Skew Clock Driver
Figure 3 shows a configuration to equalize skew between met-
al traces of different lengths. In addition to low skew between
outputs, the LVPSCB can be programmed to stagger the tim-
ing of its outputs. The four groups of output pairs can each be
programmed to different output timing. Skew timing can be
adjusted over a wide range in small increments with the appro-
priate strapping of the function select pins. In this configuration
the 4Q0 output is fed back to FB and configured for zero skew.
The other three pairs of outputs are programmed to yield dif-
ferent skews relative to the feedback. By advancing the clock
signal on the longer traces or retarding the clock signal on
shorter traces, all loads can receive the clock pulse at the
same time.
In this illustration the FB input is connected to an output with
0-ns skew (xF1, xF0 = MID) selected. The internal PLL syn-
chronizes the FB and REF inputs and aligns their rising edges
to insure that all outputs have precise phase alignment.
Clock skews can be advanced by ±6 time units (t ) when using
U
an output selected for zero skew as the feedback. A wider range of
delays is possible if the output connected to FB is also skewed.
Since “Zero Skew”, +t , and –t are defined relative to output
U
U
groups, and since the PLL aligns the rising edges of REF and FB,
it is possible to create wider output skews by proper selection of the
xFn inputs. For example a +10 t between REF and 3Qx can be
U
achieved by connecting 1Q0 to FB and setting 1F0 = 1F1 = GND,
3F0 = MID, and 3F1 = High. (Since FB aligns at –4 t and 3Qx
U
8
CY7B9911V
3.3V RoboClock+
skews to +6 t , a total of +10 t skew is realized.) Many other con-
figurations can be realized by skewing both the output used as the
FB input and skewing the other outputs.
simultaneously and are out of phase on their rising edge. This
U
U
1
will allow the designer to use the rising edges of the
⁄
fre-
2
1
quency and ⁄ frequency outputs without concern for rising-
4
edge skew. The 2Q0, 2Q1, 1Q0, and 1Q1 outputs run at 80
MHz and are skewed by programming their select inputs ac-
cordingly. Note that the FS pin is wired for 80-MHz operation
because that is the frequency of the fastest output.
REF
FB
REF
REF
FS
4Q0
4Q1
4F0
4F1
FB
REF
20 MHz
FS
3Q0
3Q1
3F0
3F1
10 MHz
4Q0
4F0
4Q1
4F1
2Q0
2Q1
2F0
2F1
5 MHz
3Q0
3Q1
3F0
3F1
1Q0
1Q1
1F0
1F1
20 MHz
2Q0
2Q1
2F0
2F1
TEST
1F0
1F1
1Q0
1Q1
7B9911V–11
Figure 4. Inverted Output Connections
TEST
7B9911V–13
Figure 4 shows an example of the invert function of the
LVPSCB. In this example the 4Q0 output used as the FB input
is programmed for invert (4F0 = 4F1 = HIGH) while the other
three pairs of outputs are programmed for zero skew. When
4F0 and 4F1 are tied HIGH, 4Q0 and 4Q1 become inverted
zero phase outputs. The PLL aligns the rising edge of the FB
input with the rising edge of the REF. This causes the 1Q, 2Q,
and 3Q outputs to become the “inverted” outputs with respect
to the REF input. By selecting which output is connect to FB,
it is possible to have 2 inverted and 6 non-inverted outputs or
6 inverted and 2 non-inverted outputs. The correct configura-
tion would be determined by the need for more (or fewer) in-
verted outputs. 1Q, 2Q, and 3Q outputs can also be skewed
to compensate for varying trace delays independent of inver-
sion on 4Q.
Figure 6. Frequency Divider Connections
Figure 6 demonstrates the LVPSCB in a clock divider applica-
tion. 2Q0 is fed back to the FB input and programmed for zero
skew. 3Qx is programmed to divide by four. 4Qx is pro-
grammed to divide by two. Note that the falling edges of the
4Qx and 3Qx outputs are aligned. This allows use of the rising
1
1
edges of the ⁄ frequency and ⁄ frequency without concern
2
4
for skew mismatch. The 1Qx outputs are programmed to zero
skew and are aligned with the 2Qx outputs. In this example,
the FS input is grounded to configure the device in the 15- to
30-MHz range since the highest frequency output is running at
20 MHz.
Figure 7 shows some of the functions that are selectable on
the 3Qx and 4Qx outputs. These include inverted outputs and
outputs that offer divide-by-2 and divide-by-4 timing. An invert-
ed output allows the system designer to clock different sub-
systems on opposite edges, without suffering from the pulse
asymmetry typical of non-ideal loading. This function allows
the two subsystems to each be clocked 180 degrees out of
phase, but still to be aligned within the skew spec.
REF
FB
20 MHz
REF
FS
40 MHz
4Q0
4F0
4F1
The divided outputs offer a zero-delay divider for portions of
the system that need the clock to be divided by either two or
four, and still remain within a narrow skew of the “1X” clock.
Without this feature, an external divider would need to be add-
ed, and the propagation delay of the divider would add to the
skew between the different clock signals.
4Q1
20 MHz
80 MHz
3Q0
3Q1
3F0
3F1
2F0
2F1
2Q0
2Q1
1Q0
1Q1
1F0
1F1
TEST
These divided outputs, coupled with the Phase Locked Loop,
allow the LVPSCB to multiply the clock rate at the REF input
by either two or four. This mode will enable the designer to
distribute a low-frequency clock between various portions of
the system, and then locally multiply the clock rate to a more
suitable frequency, while still maintaining the low-skew charac-
teristics of the clock driver. The LVPSCB can perform all of the
functions described above at the same time. It can multiply by
two and four or divide by two (and four) at the same time that
it is shifting its outputs over a wide range or maintaining zero
skew between selected outputs.
7B9911V–12
Figure 5. Frequency Multiplier with Skew Connections
Figure 5 illustrates the LVPSCB configured as a clock multipli-
er. The 3Q0 output is programmed to divide by four and is fed
back to FB. This causes the PLL to increase its frequency until
the 3Q0 and 3Q1 outputs are locked at 20 MHz while the 1Qx
and 2Qx outputs run at 80 MHz. The 4Q0 and 4Q1 outputs are
programmed to divide by two, which results in a 40-MHz wave-
form at these outputs. Note that the 20- and 40-MHz clocks fall
9
CY7B9911V
3.3V RoboClock+
REF
LOAD
Z
0
110-MHz
INVERTED
FB
REF
FS
27.5-MHz
DISTRIBUTION
CLOCK
LOAD
LOAD
4Q0
4Q1
4F0
4F1
27.5-MHz
Z
0
3Q0
3Q1
2Q0
2Q1
3F0
3F1
2F0
2F1
110-MHz
ZERO SKEW
Z
0
1Q0
1Q1
1F0
LOAD
110-MHz
SKEWED –2.273 ns (–4tU)
1F1
TEST
Z
0
7B9911V–14
Figure 7. Multi-Function Clock Driver
LOAD
REF
Z
0
L1
FB
LOAD
LOAD
SYSTEM
CLOCK
REF
FS
4F0
4F1
L2
Z
0
4Q0
4Q1
3Q0
3Q1
3F0
3F1
L3
2F0
2F1
2Q0
2Q1
Z
0
1F0
1F1
1Q0
1Q1
L4
FB
REF
TEST
FS
LOAD
4Q0
4Q1
4F0
4F1
3F0
3F1
2F0
2F1
Z
0
3Q0
3Q1
2Q0
2Q1
LOAD
1F0
1Q0
1Q1
1F1
TEST
7B9911V–15
Figure 8. Board-to-Board Clock Distribution
Figure 8 shows the CY7B9911V connected in series to con-
struct a zero-skew clock distribution tree between boards. De-
lays of the downstream clock buffers can be programmed to
compensate for the wire length (i.e., select negative skew
equal to the wire delay) necessary to connect them to the mas-
ter clock source, approximating a zero-delay clock tree. Cas-
caded clock buffers will accumulate low-frequency jitter be-
cause of the non-ideal filtering characteristics of the PLL filter.
It is recommended that not more than two clock buffers be
connected in series.
10
CY7B9911V
3.3V RoboClock+
Ordering Information
Accuracy
Package
Name
Operating
Range
(ps)
500
700
Ordering Code
Package Type
32-Lead Plastic Leaded Chip Carrier
32-Lead Plastic Leaded Chip Carrier
CY7B9911V–5JC
CY7B9911V–7JC
J65
J65
Commercial
Commercial
Document #: 38-00765-B
Package Diagram
32-Lead Plastic Leaded Chip Carrier J65
51-85002-B
© Cypress Semiconductor Corporation, 1999. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.
相关型号：
CY7B9911-7JCT
PLL Based Clock Driver, 7B Series, 4 True Output(s), 0 Inverted Output(s), PQCC32, PLASTIC, LCC-32
CYPRESS
©2020 ICPDF网 联系我们和版权申明