CM2400-04HB [CALMIRCO]
Universal Serial Bus Transceiver with Level Translator; 通用串行总线收发器，电平转换器
| 型号： | CM2400-04HB |
| 厂家： | 
CALIFORNIA MICRO DEVICES CORP |
| 描述： | Universal Serial Bus Transceiver with Level Translator |
| 文件： | 总14页 (文件大小：179K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PRELIMINARY
CM2400-02/03/04
Universal Serial Bus Transceiver with Level Translator
Features
Product Description
•
•
Complies with USB Specification Rev 1.1 & 2.0
Supports full speed (12Mbit/sec.) and low speed
(1.5Mbits/sec.) modes
Integrated 5V to 3.3V regulator
Used as a USB device transceiver or
host transceiver
The CM2400-02/03/04 Universal Serial Bus (USB)
transceiver is fully compliant with the USB specification
Rev 1.1 and 2.0. It supports a speed of 12Mbits/s (Full
Speed Mode).
•
•
An internal level shifter allows interface to Application
Specific ICs (ASICs) and Programmable Logic Devices
(PLD's) running at core voltages of 1.65V to 3.6V.
•
V
disconnection indication through V and V
BUS P M
outputs
The CM2400-02/03/04 features an internal 5V to 3.3V
regulator which is used to power the USB transceiver
•
•
•
•
•
•
•
Two single-ended receivers with hysteresis
USB Detection of V
via level translator
BUS
via the USB supply V .
Stable RCV output during SE0 condition
Low power operation from V
BUS
CC
The CM2400-04 features a Mode Input pin (MODE)
which allows the device to operate in either single or
differential input mode.
Supports 1.65V to 3.6V I/O voltage levels
Full industrial operating range -40 to 85 °C
Available in small HBCC-16 and
TSSOP-16 packages
This device is ideal for portable electronic devices such
as mobile phones, digital still cameras, PDAs (Personal
Digital Assistants) and IAs (Information Appliances).
The CM2400-02/03/04 is packaged in a small form-fac-
tor 16-lead HBCC or TSSOP package to conserve
board space.
Applications
•
•
•
•
Wireless handsets
Digital still cameras
PDAs (Personal Digital Assistants)
IAs (Information Appliances)
Simplified Block Schematic
Voltage
Regulator
VBUS
VCC
VREG
VPU
ENUM
OE
VMO/FSEO
D+
D-
VPO/VO
SPND
RCV
SPEED
MODE*
VP
VM
GND
* MODE pin available on
CM2400-04 only.
© 2004 California Micro Devices Corp. All rights reserved.
08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
1
PRELIMINARY
CM2400-02/03/04
PACKAGE / PINOUT DIAGRAM
1
2
3
4
16
15
14
13
12
VPU
ENUM
OE
VBUS
5
6
7
8
9
5
6
7
8
9
SPND
D -
SPND
D -
VREG
VMO/FSEO
VPO/VO
D +
4
3
2
10
11
12
4
3
2
10
11
12
VM
VP
D +
VM
VP
D +
HBCC-16
GND
17
HBCC-16
GND
17
RCV
VP
VPO/VO
VMO/FSEO
VPO/VO
VMO/FSEO
5
6
7
8
RCV
RCV
11
10
VM
D -
1
16 15 14
13
1
16 15 14
13
VREG
VREG
OE
OE
SPND
GND
SPEED
VCC
9
CM2400-02TS/-03TS
Top View
CM2400-04HB
Bottom View
CM2400-02HB/-03HB
Bottom View
Note: These drawings are not to scale.
PIN DESCRIPTIONS
HBCC-16 TSSOP-16
PINS
PINS
NAME
DESCRIPTION
1
3
OE
Input for Output Enable (Active low). Enables transceiver driver to transmit data on
the USB bus. When OE pin = LOW, driver circuitry is enabled.
2
3
4
5
6
4
5
6
7
8
RCV
VP
Differential receiver output of D+ and D- input data lines. The output state of RCV
is preserved and stable during an SE0 condition.
Single-ended D+ receiver output for detection of a single-ended zero or error con-
ditions
VM
Single-ended D- receiver output for detection of a single-ended zero or error con-
ditions.
SPND
MODE
Suspend input. Allows the device to enter a low power state while the USB is inac-
tive.
Mode input (CM2400-04). Selects between differential (VPO, VMO) and single-
ended mode (VO, FSEO).
GND
VCC
Ground input (CM2400-02/03).
7
8
9
Supply voltage for digital I/O pins. Voltages supported: 1.65 to 3.6V.
10
SPEED
Speed Input. If SPEED is logic '1', selects full speed. If SPEED is logic '0', selects
low speed. SPEED changes slope rise and fall time on D+ and D-.
9
11
12
D-
Negative USB data connection.
10
D+
Positive USB data connection. In full-speed connect mode, connect to VPU via a
1.5kΩ resistor. Tolerance of this resistor is defined in the USB specification REV
1.1 & 2.0
11
12
13
13
14
15
VPO/VO
Driver data input.
VMO/FSEO Driver data input.
VREG
Regulated supply voltage output during USB operation of VBUS. 1µF decoupling
capacitor is required.
14
15
16
1
VBUS
VPU
Supply voltage input. Can be directly connected to USB VBUS
.
Pull-up supply voltage. Pin function is controlled by input ENUM.
© 2004 California Micro Devices Corp. All rights reserved.
2
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
08/24/04
PRELIMINARY
CM2400-02/03/04
PIN DESCRIPTIONS (CONT’D)
16
17
2
ENUM
GND
Enumerate, allows software to control connection of the external pull-up via the
level translator. If ENUM = LOW then VPU is floating. If ENUM = HIGH then VPU is
internally connected to VREG
.
−
The ground terminal is connected to the exposed diepad (heatsink).
Ordering Information
PART NUMBERING INFORMATION
Lead-free FInishing2
Standard FInishing
PADS/
Package
LEADS
Ordering Part Number1
Ordering Part Number1
CM2400-02HA
Part Marking
CM240002HB
CM240002TS
CM240003HB
CM240003TS
CM240004HB
Part Marking
16
16
16
16
16
HBCC-16
TSSOP-16
HBCC-16
TSSOP-16
HBCC-16
CM2400-02HB
CM2400-02TS
CM2400-03HB
CM2400-03TS
CM2400-04HB
CM240002HA
CM240002TR
CM240003HA
CM240003TR
CM240004HA
CM2400-02TR
CM2400-03HA
CM2400-03TR
CM2400-04HA
Note 1: Parts are shipped in Tape & Reel form unless otherwise specified.
Note 2: Lead-free, 100% tin plated.
Specifications
ABSOLUTE MAXIMUM RATINGS
PARAMETER
RATING
+1000
UNITS
ESD Protection (All Pins except D+/D- pins, HBM, See Note 1)
ESD Protection (D+/D- pins, HBM, See Note 1)
VBUS
V
V
V
+4000
[GND - 0.5] to +5.5
VCC
[GND - 0.5] to +6.0
[GND - 0.5] to [VCC + 0.5]
-65 to +150
V
V
VI (INPUT)
Storage Temperature Range
°C
Operating Temperature Range
Junction
-40 to +150
°C
Note 1: Equivalent to discharging a 100pF capacitor via a 1.5kΩresistor (Human body model).
STANDARD (RECOMMENDED) OPERATING CONDITIONS
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
VBUS
USB VBUS Supply
4.0
5.0
5.5
3.6
V
VCC
VI
DC System Supply
1.65
0
3.3
V
V
DC Input Voltage
-
-
-
VCC
3.6
VI(AI/O)
TA
Analog I/O Pins (D+, D-)
Ambient Operating Temperature Range
0
V
-40
+85
°C
© 2004 California Micro Devices Corp. All rights reserved.
08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
3
PRELIMINARY
CM2400-02/03/04
Specifications (cont’d)
ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE 1)
Supply Pins (VBUS = 4.0V to 5.5V; VCC = 1.65V to 3.6V)
SYMBOL PARAMETER CONDITIONS
VREG Regulated supply output
IBUS Operating supply current
MIN
TYP MAX UNITS
Unloaded
3.0
3.3
3.6
8
V
Full-speed TX and RX; CL=50pF on
D+/D- outputs; Note 2
mA
IBUS(IDLE) Supply current during full speed idle Full-speed idle; Notes 3 & 4
and SE0
500
µA
IBUS(DIS) Disable mode supply current
IBUS(SUSP) Suspend mode supply current
VCC not present; Note 4
60
60
µA
µA
mA
µA
µA
µA
SPND = HIGH; Notes 3 & 4
ICC
Operating I/O supply current
Full-speed TX and RX; Note 5
Full-speed idle, SE0 or suspend; Note 5
1.0
1.0
1.0
1.0
ICC(STAT) Static I/O supply current
ICC(SHARE) Supply current during sharing mode VBUS not connected; Note 5
IDX(SHARE) D+/D- load current during sharing
mode
VBUS not connected; ENUMERATE =
LOW; Note 5
VTH(VBUS) VBUS supply detection threshold
Supply lost
0.8
0.5
V
V
V
V
Supply present
Supply lost (USB_D low)
Supply present
2.4
1.4
VTH(VCC) VCC supply detection threshold
Digital Pins (VBUS = 4.0V to 5.5V; VCC = 1.8V 0.15V)
SYMBOL PARAMETER CONDITIONS
MIN
TYP MAX UNITS
VIL
VIH
VOL
Logic LOW input voltage
0.5
V
V
Logic HIGH input voltage
Logic LOW output voltage
1.2
IOL = 100µA
IOL = 2mA
0.15
0.40
V
V
VOH
Logic HIGH output voltage
IOH = 100µA
IOH = 2mA
1.50
1.25
V
V
Note 1: Operating Characteristics are over Standard Operating Conditions unless otherwise specified.
Note 2: Equivalent to discharging a 100pF capacitor via a 1.5kΩresistor (Human body model).
Note 3: Excluding any load current and VPU/VSW source current to 1.5kΩ and 15kΩ pull-up and pull-down resistors (200 µA).
Note 4: Current is drawn from VBUS of Host when device is a peripheral.
Note 5: Low current ideal for battery powered applications.
© 2004 California Micro Devices Corp. All rights reserved.
4
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
08/24/04
PRELIMINARY
CM2400-02/03/04
Specifications (cont’d)
ELECTRICAL OPERATING CHARACTERISTICS (CONT’D)
Digital Pins (VBUS = 4.0V to 5.5V; VCC = 2.5V 0.2V)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VIL
VIH
VOL
Logic LOW input voltage
0.7
V
Logic HIGH input voltage
Logic LOW output voltage
1.7
V
IOL = 100µA
IOL = 2mA
0.15
0.40
V
V
VOH
Logic HIGH output voltage
IOH = 100µA
IOH = 2mA
2.15
1.90
V
V
Digital Pins (VBUS = 4.0V to 5.5V; VCC = 1.65V to 3.6V)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VIL
VIH
VOL
Logic LOW input voltage
V
0.3 ∗ VCC
Logic HIGH input voltage
Logic LOW output voltage
V
0.6 ∗ VCC
IOL = 100µA
IOL = 2mA
0.15
0.40
V
V
VOH
Logic HIGH output voltage
IOH = 100µA
IOH = 2mA
V
CC - 0.15
V
V
VCC - 0.40
Analog I/O Pins (VBUS = 4.0V to 5.5V; VCC = 1.65V to 3.6V)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VDI
VCM
VIL
Differential receiver input
sensitivity
0.2
V
| VI(D+) - VI(D-) |
Differential receiver
common mode voltage
0.8
2.5
0.8
V
V
V
V
Single-ended receiver
logic LOW input voltage
VIH
Single-ended receiver
logic HIGH input voltage
2.0
0.4
VHYS
Single-ended receiver
Hysteresis voltage
0.7
VOL
VOH
ILZ
Logic LOW output voltage
Logic HIGH output voltage
OFF-state leakage current
Transceiver Capacitance
RL = 1.5KΩ tied to +3.6V
RL = 15KΩ tied to GND
0.3
3.6
+1
V
V
2.8
µA
pF
Ω
CIN
Pin to GND
20
RSW
Internal switch resistance at
VPU
50
39
ZDRV
Driver output impedance
(includes 33 ohm 1% resis-
tor)
Measured with steady-state drive;
See Note 6
28
44
Ω
Note 6: Rev 2.0 states ZDRV must be between 28Ω and 44Ω, when the driver is not high speed capable.
© 2004 California Micro Devices Corp. All rights reserved.
08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
5
PRELIMINARY
CM2400-02/03/04
Specifications (cont’d)
ELECTRICAL OPERATING CHARACTERISTICS (CONT’D)
Driver Characteristics & Timings (Full-speed mode only, SPEED=HIGH)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP MAX UNITS
tFR
Rise time
CL = 50 to 125pF, measured 10% to 90%
(VOH-VOL); See Figure 6
4
20
ns
tFF
Fall time
CL = 50 to 125pF, measured 10% to 90%
(VOH-VOL); See Figure 6
4
20
ns
FRFM
VCRS
Differential rise / fall time
Excluding the first transition from idle state
100
%
V
matching (tFR / tFF
)
Output signal crossover
voltage
Excluding the first transition from idle state;
See Figure 9
1.65
tPLH(DRV) Driver propagation delay
LOW-to-HIGH transition; See Figure 9
HIGH-to-LOW transition; See Figure 9
18
18
ns
ns
(VO / VPO ➔ D+ / D- ;
tPHL(DRV)
FSEO / VMO ➔ D+ / D-
tPHZ
tPLZ
tPZH
tPZL
Driver disable delay
(OE ➔ D+ / D-)
HIGH-to-OFF; See Figure 7
LOW-to-OFF; See Figure 7
OFF-to-HIGH; See Figure 7
OFF-to-LOW; See Figure 7
15
15
15
15
ns
ns
ns
ns
Driver enable delay
(OE ➔ D+ / D-)
Driver Characteristics & Timings (Low-speed mode only, SPEED=LOW)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP MAX UNITS
tLR
Rise time
CL = 200 to 600pF, measured 10% to 90%
(VOH-VOL); See Figure 6
75
300
ns
tLF
Fall time
CL = 200 to 600pF, measured 10% to 90%
(VOH-VOL); See Figure 6
75
300
ns
FRFM
VCRS
Differential rise / fall time
Excluding the first transition from idle state
80
125
2.0
%
V
matching (tFR / tFF
)
Output signal crossover
voltage
Excluding the first transition from idle state;
See Figure 9
1.3
Receiver Timings (Full-speed and low-speed modes)
SYMBOL PARAMETER
Differential Receiver
CONDITIONS
MIN
TYP MAX UNITS
tPLH(RCV) Driver propagation delay
LOW-to-HIGH transition; See Figure 8
HIGH-to-LOW transition; See Figure 8
15
15
ns
ns
(D+ / D- ➔ RCV)
tPHL(RCV)
Single-ended Receiver
tPLH(SE)
tPHL(SE)
Driver propagation delay
(D+ / D- ➔ VP / VM)
LOW-to-HIGH transition; See Figure 8
HIGH-to-LOW transition; See Figure 8
18
18
ns
ns
© 2004 California Micro Devices Corp. All rights reserved.
6
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
08/24/04
PRELIMINARY
CM2400-02/03/04
Specifications (cont’d)
Test Loads
Test Point
Test Point
33Ω
DUT
DUT
15pF
50pF
Load for V / V and
RCV delay measurements
Load for D+ and D- delay measurements
(MAX and MIN Timing)
P
M
Test Point
33Ω
200Ω
50pF
DUT
V = VREG(3.3) for tPZL and tPLZ
V = 0 v for tPZH and tPHZ
V
Load for ENABLE and DISABLE
delay measurements.
© 2004 California Micro Devices Corp. All rights reserved.
08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
7
PRELIMINARY
CM2400-02/03/04
Performance Information
CM2400-02/03/04 Typical DC Characteristics (nominal conditions unless specified otherwise)
300
1.00
250
200
150
100
0.50
0.00
-0.50
-1.00
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4
VOLTAGE [V]
4.1
4.3
4.5
4.7
4.9
5.1
5.3
5.5
V
V
VOLTAGE [V]
CC
BUS
Figure 3. VBUS Current in Idle Mode (SPND=LOW)
Figure 1. V Current in Idle Mode (SPND=LOW)
CC
1.00
0.50
0.00
-0.50
60.0
55.0
50.0
45.0
40.0
-1.00
4.1
4.3
4.5
4.7
4.9
5.1
5.3
5.5
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4
V
VOLTAGE [V]
V
VOLTAGE[V]
BUS
CC
Figure 4. V
Current in Suspend Mode
(SPND=HIGH)
BUS
Figure 2. V Current in Suspend Mode
CC
(SPND=HIGH)
© 2004 California Micro Devices Corp. All rights reserved.
8
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
08/24/04
PRELIMINARY
CM2400-02/03/04
Performance Information (cont’d)
CM2400-02/03/04 Typical AC Characteristics (nominal conditions unless specified otherwise)
D+
D
-
Figure 5. Rise and Fall Time Matching for Full-Speed Mode
D+
D
-
Figure 6. Rise and Fall Time Matching for Low-Speed Mode
© 2004 California Micro Devices Corp. All rights reserved.
08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
9
PRELIMINARY
CM2400-02/03/04
Performance Information (cont’d)
CM2400 Timing Diagrams
3.3V
VCRS
INPUT
VCRS
t
t
t
t
FR, LR
FF, LF
0V
t
t
t
t
PHL(RCV)
PHL(SE)
PLH(RCV)
PLH(SE)
VOH
VOL
90%
90%
VOH
0.9V
OUTPUT
0.9V
10%
10%
VOL
Figure 7. Rise and Fall Timing
Figure 9. D+, D- to RCV, V and V Timing
P
M
1.65V
1.65V
INPUT
0.9V
0.9V
0.9V
INPUT
0.9V
0V
t
t
PHZ
PLZ
0V
t
t
PZH
PZL
t
t
PHL(DRV)
PLH(DRV)
VOH
0.3V
-
VOH
OUTPUT
VCRS
VCRS
OUTPUT
VCRS
0.3V
+
VOL
VOL
Figure 8. OE to D+, D- Timing
Figure 10. V /V , FSEO/V
to D+, D- Timing
O
PO
MO
© 2004 California Micro Devices Corp. All rights reserved.
10 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
08/24/04
PRELIMINARY
CM2400-02/03/04
Functional Description
The CM2400-02/03/04 USB Transceiver supports 3 dif-
ferent power supply configurations, which can be con-
figured dynamically. Table 1 details the various
configurations. In Normal Mode the internal regulator
D- lines while in sharing mode. In this mode, V and
P
V
are driven high while RCV and USB_DET are
M
driven low.
In Disable and Sharing Mode, all input/output pins fol-
low the states defined in Table 2.
produces 3.3V from V
to power the internal drivers
BUS
and receivers associated with the USB protocol.
Sharing Mode
State
Disable Mode
State
VBUS
VCC
CONFIGURATION
Normal Mode
PIN
Connected
Connected
Connected
Not Connected
Connected
VBUS
VREG
VCC
VBUS < 3.6V
Pulled Down
Present
4.1V to 5.5V
3.3V Out
Disable Mode
Sharing Mode
Not Connected
Not Present
High-Z (off)
Table 1: Power Supply Connections
VPU
High-Z (off)
There are three power supply configurations for the
CM2400-02/03/04: Normal mode, Disable mode and
Sharing mode. These three modes can be changed
dynamically.
D+, D-
High-Z
H
High-Z
Invalid
VP , VM
RCV
USB_DET
Inputs
L
L
Invalid
Invalid
High-Z
Normal mode occurs when the V
and V
inputs
BUS
CC
are both connected to a source. V
is tied to a 5V
High-Z
BUS
source for 5V operation. The internal regulator of the
CM2400-02/03/04 provides 3.3V output on V . The
Table 2: Pin States in Disable or Sharing Mode
REG
Table 3 lists the functions of the modes associated with
suspend and OE pins. When Suspend is low and OE is
high, signal levels on D+ and D- are determined by
other USB devices and pull-up/down resistors. In Sus-
pend Mode (SPND = HIGH) the differential receiver is
inactive and output RCV is always LOW. Out of sus-
pend signaling is detected via the single-ended receiv-
V
input is connected to an independent source that
CC
can range from 1.65V to 3.6V.
When V is not connected and V
is connected,
BUS
CC
the device is in Disable mode. The D+ and D- pins are
in tri-state and power consumption drops to a suspend
state level.
ers V and V . During suspend and while the output is
still enabled (OE = LOW), D+ and D- lines are driven to
their intended states.
P
M
In Sharing mode, V
is connected while V
is
BUS
CC
below 3.6V. The D+ and D- pins are in tri-state and the
CM2400-02/03/04 allows external signals (≤3.6V) to
share these two lines. The CM2400-02/03/04 is
designed to draw almost zero current from the D+ and
VP/VM
SUSPEND OE
D+ / D-
Driver & Receiver Active
Receiving
RCV
Active
Active
Function
L
L
L
H
L
Active
Active
Normal driving mode. Differential receiver active
Driver Tri-stated. Differential receiver active.
H
Driving
Inactive
RCV=L
Active Driving during ’suspend’. Differential receiver inactive.
H
H
High-Z
Inactive
RCV=L
Active Low-power state.
Table 3: Function Selection.
© 2004 California Micro Devices Corp. All rights reserved.
08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com 11
PRELIMINARY
CM2400-02/03/04
Functional Description (cont’d)
Detailed in Table 4 and Table 5 are the operating
modes for the CM2400-02/03/04. The CM2400-02 fea-
tures a fixed, single-ended input operating mode which
is summarized in Table 4. The CM2400-03 features a
differential-pair input operating mode which is summa-
rized in Table 5. The CM2400-04 input mode is select-
able via the MODE input. Table 4 and Table 5
summarize both operating modes for the CM2400-04.
Table 6 details the receiving function when OE is HIGH
(driver disabled). RCV denotes the signal level on the
output RCV just before an SE0 state occurs. This level
is stable during the SE0 period.
VP
VM
D+/D-
RCV
L
Differential Logic ’0’
Differential Logic ’1’
SE0
L
H
L
H
L
L
H
On the CM2400-02, the two driver inputs function as
V
and FSE0 inputs. On the CM2400-03, the driver
RCV*
O
inputs function as V
and V . On the CM2400-04,
MO
PO
* Denotes RCV is stable in last state before SE0 condition.
when the MODE input is HIGH, differential-pair input
mode is selected and the two driver inputs function as
Table 6: Receiving Function (SPND = L)
A regulator bypass option can be utilized by shorting
VBUS to VREG and connecting to a 3.3v supply.
V
and V . When MODE is LOW, the single-ended
PO
MO
input data interface mode is selected and the two driver
inputs function as V and FSE0.
O
VO (VPO
)
FSE0 (VMO)
MODE
Result
Logic ‘0’
SE0
L
L
L
L
H
L
(single-ended)
H
H
Logic ‘1’
SE0
H
Table 4: Single-ended Input Operating Mode,
CM2400-02 and CM2400-04 in Single-ended
Input Mode (OE = L)
VO (VPO
)
FSE0 (VMO)
MODE
Result
SE0
H
L
L
L
H
L
(differential)
Logic ‘0’
Logic ‘1’
Undefined
H
H
H
Table 5: Differential-pair Input Operating Mode,
CM2400-03 and CM2400-04 in Differential-pair
Input Mode (OE = L)
© 2004 California Micro Devices Corp. All rights reserved.
12 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
08/24/04
PRELIMINARY
CM2400-02/03/04
Mechanical Details
The CM2400-02/03/04 family is available in a 16-lead
HBCC and 16-lead TSSOP packages.The mechanical
details for these packages are presented below.
Mechanical Package Diagrams
HBCC-16 Mechanical Specifications
TOP VIEW
Dimensions for the CM2400-02HB, CM2400-03HB and
CM2400-04HB devices packaged in 16-pin HBCC
packages are presented below.
A
D
13
9
A1
PACKAGE DIMENSIONS
E
Package
Pins
HBCC-16
16
Millimeters
Min Max
Inches
Max
Dimensions
Min
1
5
A
-
0.80
0.10
0.0315
0.0039
SIDE VIEW
A1
0.05
b1
b2
b3
0.25
0.30
0.30
0.35
0.40
0.40
0.0138
0.0157
0.0157
BOTTOM VIEW
D
2.90
1.45
3.10
1.55
0.1220
0.0610
e1
Dh
e
Dh
E
2.90
1.75
3.10
1.85
0.1220
0.0728
13
9
Eh
e
0.50 TYP.
0.0197 TYP.
e
e4
Eh
e2
e1
2.50 TYP.
2.50 TYP.
2.45 TYP.
2.45 TYP
0.0984 TYP.
0.0984 TYP.
0.0965 TYP.
0.0965 TYP.
e2
e3
1/2 e4
5
1
16
e4
Detail C
Detail B
1/2 e3
Detail A
# per tube
120 pieces*
2500 pieces
e3
# per tape
and reel
Controlling dimension: millimeters
CONTACT (PIN) DIMENSIONS
* This is an approximate number which may vary.
CF#0.20x45ο
b
b
b
3
2
1
b
b
b
2
3
1
Detail A
Detail B
Detail C
Dimensions for HBCC-16 Package
© 2004 California Micro Devices Corp. All rights reserved.
08/24/04 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com 13
PRELIMINARY
CM2400-02/03/04
Mechanical Details (cont’d)
TSSOP-16 Mechanical Specifications
Mechanical Package Diagrams
Dimensions for the CM2400-02TS and CM2400-03TS
devices packages are presented below.
For complete information on the TSSOP-16 package,
see the California Micro Devices TSSOP Package
Information document.
TOP VIEW
D
16 15 14 13 12 11 10
9
PACKAGE DIMENSIONS
E
Package
Pins
TSSOP
16
H
Pin 1 Marking
Millimeters
Min Max
Inches
Max
Dimensions
Min
—
1
2
3
4
5
6
7
8
A
—
1.10
0.15
0.30
0.20
5.10
4.50
0.0433
0.006
A1
0.05
0.19
0.09
4.90
4.30
0.002
0.0075
0.0035
0.193
0.169
B
0.0118
0.0079
0.201
SIDE VIEW
C
D
A
A1
SEATING
PLANE
E
0.177
B
e
e
0.65 BSC
0.0256 BSC
H
L
6.25
0.50
6.50
0.70
0.246
0.020
0.256
0.028
END VIEW
# per tube
Consult Factory
2500 pcs
# per tape
and reel
C
Controlling dimension: millimeters
L
Dimensions for the TSSOP-16 Package
© 2004 California Micro Devices Corp. All rights reserved.
14 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
●
Tel: 408.263.3214
●
Fax: 408.263.7846
●
www.calmicro.com
08/24/04
相关型号：
©2020 ICPDF网 联系我们和版权申明