Q45BW13LP [BANNER]
Q45BW13 Series Sensors;型号: | Q45BW13LP |
厂家: | Banner Engineering |
描述: | Q45BW13 Series Sensors |
文件: | 总8页 (文件大小:325K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Q45BW13 Series Sensors
Datasheet
Universal voltage photoelectric sensors with isolated solid-state output
•
Advanced one-piece photoelectric sensors with outstanding opꢀcal performance and
extremely rugged design
•
•
•
Universal supply voltage: 12 V dc to 250 V dc or 24 V ac to 250 V ac
Opto-isolated solid-state relay output; 300 mA max. load at up to 250 V ac, 250 V dc
Full line includes opposed, diffuse, retroreꢁecꢀve, convergent, and glass and plasꢀc fiber
opꢀc sensing modes
Selectable light/dark operate
•
•
•
•
Versaꢀle plug-in modules available for output ꢀming logic and/or signal strength display
1
™
Highly visible Power, Signal (AID System ), and Output indicator LEDs
Choice of prewired 2 m (6.5 ꢂ) or 9 m (30 ꢂ) unterminated cable or Mini-style quick-
disconnect fiꢃng
•
•
Versaꢀle mounꢀng opꢀons
Designed to withstand 1200 psi washdown; exceeds its NEMA 6P and IEC IP67 raꢀng
WARNING: Not To Be Used for Personnel Protecꢀon
Never use this device as a sensing device for personnel protecꢀon. Doing so could lead to serious injury or
death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel
safety applicaꢀons. A sensor failure or malfuncꢀon can cause either an energized or de-energized sensor output
condiꢀon.
Models
To order the 9 m (30 ꢂ) cable models, add the suffix "W/30" to the cabled model number. For example: Q453E W/30.
Models with a quick disconnect (QD) connector require a maꢀng cable.
Opposed Mode Emiꢁer (E) and Receiver (R) Models
Because of their extremely high excess gain, these opposed-mode sensors are an excellent opꢀon for sensing in
contaminated or dirty areas, and are also the best choice for long-range sensing.
OPPOSED
Infrared, 880 nm
Models
Range
Cable
Supply Voltage
Output Type
Q453E Emiꢁer
2-wire 2 m (6.5 ꢂ)
4-wire 2 m (6.5 ꢂ)
3-pin Mini QD
4-pin Mini QD
Universal 12 to 250 V dc
Q45BW13R Receiver
Q453EQ Emiꢁer
Q45BW13RQ Receiver
60 m (200 ꢂ)
Isolated SPST Solid-state Switch
or
24 to 250 V ac
Retroreꢂecꢀve Mode Models
The visible red sensing beam of these sensors makes them very easy to align. Model Q45BW13LP
polarizes the emiꢄed light and filters out unwanted reꢁecꢀons, making sensing possible in
applicaꢀons otherwise considered unsuited to retroreꢁecꢀve sensing. Performance is specified
using the model BRT-3 3-inch reꢁector (go to www.bannerengineering.com for more
informaꢀon).
P
RETRO
POLAR RETRO
Visible red, 680 nm
(non-polarized)
Visible red, 680 nm
(polarized)
Retroreꢁecꢀve range is specified using one model BRT-3 retroreꢁector (3-inch diameter). Actual sensing range may be more or less than
specified, depending upon the efficiency and reꢁecꢀve area of the retroreꢁector used.
1
U.S. Patent number 4356393
Original Document
53999 Rev. D
31 January 2017
53999
Q45BW13 Series Sensors
Non-Polarized
Cable
Models
Range
Supply Voltage
Output Type
Q45BW13LV
Q45BW13LVQ
4-wire 2 m (6.5 ꢂ)
Universal 12 to 250 V dc
0.08 to 9 m (3 in to 30
Isolated SPST Solid-state Switch
or
4-Pin Mini QD
ꢂ)
24 to 250V ac
Polarized
Models
Range
Cable
Supply Voltage
Output Type
Q45BW13LP
Q45BW13LPQ
4-wire 2 m (6.5 ꢂ)
4-Pin Mini QD
Universal 12 to 250 V dc
0.15 to 6 m (6 in to 20
Isolated SPST Solid-state Switch
or
ꢂ)
24 to 250 V ac
Diffuse Mode Models
These diffuse-mode models detect objects by sensing the reꢁecꢀon of their own emiꢄed light. Ideal for use when the
reꢁecꢀvity and profile of the object to be sensed are sufficient to return a large percentage of emiꢄed light back to
the sensor. Model Q45BW13DX is the first choice for diffuse-mode applicaꢀons when there are no background
objects to falsely return light.
DIFFUSE
Infrared, 880 nm
Short Range
Models
Range
Cable
Supply Voltage
Output Type
Q45BW13D
Q45BW13DQ
4-wire 2 m (6.5 ꢂ)
4-Pin Mini QD
Universal 12 to 250 V dc
450 mm (18 in)
Isolated SPST Solid-state Switch
or
24 to 250 V ac
Long Range
Models
Range
Cable
Supply Voltage
Output Type
Q45BW13DL
Q45BW13DLQ
4-wire 2 m (6.5 ꢂ)
4-Pin Mini QD
Universal 12 to 250 V dc
1. 8 m (6 ꢂ)
Isolated SPST Solid-state Switch
or
24 to 250 V ac
High Power
Models
Range
Cable
Supply Voltage
Output Type
Q45BW13DX
Q45BW13DXQ
4-wire 2 m (6.5 ꢂ)
4-Pin Mini QD
Universal 12 to 250 V dc
3 m (10 ꢂ)
Isolated SPST Solid-state Switch
or
24 to 250 V ac
Convergent Mode Models
These sensors are ideal for reꢁecꢀve sensing of very small parts or profiles, and can accurately sense the posiꢀon of
parts approaching from the side. Will ignore all but highly reꢁecꢀve objects that are outside the sensing range.
CONVERGENT
VISIBLE RED
Visible red, 680 nm
Output Type
Models
Focus
Cable
Supply Voltage
Q45BW13CV
Q45BW13CVQ
4-wire 2 m (6.5 ꢂ)
4-pin Mini QD
Universal 12 to 250 V dc
38 mm (1.5 in)
Isolated SPST Solid-state Switch
or
Spot Size at Focus: 1.3
mm (0.05 in)
24 to 250 V ac
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 53999 Rev. D
Q45BW13 Series Sensors
Models
Focus
Cable
Supply Voltage
Output Type
Q45BW13CV4
Q45BW13CV4Q
4-wire 2 m (6.5 ꢂ)
4-pin Mini QD
Universal 12 to 250 V dc
100 mm (4 in)
Isolated SPST Solid-state Switch
or
Spot Size at Focus: 1.5
mm (0.06 in)
24 to 250 V ac
Glass Fiber-Opꢀc Models
These models are an excellent choice for glass fiber opꢀc applicaꢀons where faster sensor response is not important.
Their high excess gain means that opposed individual fibers can operate reliably in many very hosꢀle environments.
Also, special miniature bifurcated fiber opꢀc assemblies with bundle sizes as small as .5 mm (.020 in) dia. may be used
successfully for diffuse-mode sensing when using sensor model Q45BW13F(Q). For more informaꢀon on compaꢀble
glass fiber opꢀcs, go to www.bannerengineering.com.
GLASS FIBER
Infrared, 880 nm and Visible
red, 650 nm
Infrared, 880 nm
Models
Range
Cable
Supply Voltage
Output Type
Q45BW13F
Q45BW13FQ
4-wire 2 m (6.5 ꢂ)
4-Pin Mini QD
Universal 12 to 250 V dc
Range varies by sensing
mode and fiber opꢀcs
used
Isolated SPST Solid-state Switch
or
24 to 250V ac
Visible red, 650 nm
Models
Range
Cable
Supply Voltage
Output Type
Q45BW13FV
Q45BW13FVQ
4-wire 2 m (6.5 ꢂ)
4-Pin Mini QD
Universal 12 to 250 V dc
Range varies by sensing
mode and fiber opꢀcs
used
Isolated SPST Solid-state Switch
or
24 to 250 V ac
Plasꢀc Fiber-Opꢀc Models
Lower in cost than glass fiber opꢀcs, plasꢀc fiber opꢀcs are ideal for use in situaꢀons where environmental condiꢀons
allow (for example, low levels of acids, alkalis, and solvents). Most are easily cut to length in the field, and are
available in a variety of sensing end styles. For more informaꢀon on compaꢀble plasꢀc fiber opꢀcs, go to
www.bannerengineering.com.
GLASS FIBER
Visible red, 660 nm
Models
Range
Cable
Supply Voltage
Output Type
Q45BW13FP
Q45BW13FPQ
4-wire 2 m (6.5 ꢂ)
4-Pin Mini QD
Universal 12 to 250 V dc
Range varies by sensing
mode and fiber opꢀcs
used
Isolated SPST Solid-state Switch
or
24 to 250V ac
Overview
Status indicator LEDs for power, signal, and output are clearly visible beneath a raised dome in the sensor’s transparent o-ring-sealed
polycarbonate cover. Also located beneath the sensor’s o-ring-sealed cover are controls for light/dark operate selecꢀon and the
sensiꢀvity adjustment.
•
•
The power indicator (green) lights when power is applied to the sensor.
The signal indicator (red) lights when the sensor sees its modulated light source and pulses at a rate proporꢀonal to the
2
™
strength of the received light signal; this is the AID Alignment Indicaꢀng Device .
•
The output indicator (amber) lights when the sensor’s output is conducꢀng. This indicator is especially useful when a ꢀming
logic module is used and signal and output condiꢀons are not concurrent.
2
US patent no. 4356393
P/N 53999 Rev. D
www.bannerengineering.com - Tel: +1-763-544-3164
3
Q45BW13 Series Sensors
1. LEDs
5
4
•
•
•
Green LED: Power on indicator
Red LED: Signal indicator
Amber LED: Output status indicator
2. Opꢀonal LED signal strength display
3. Opꢀonal ꢀming adjustment
4. Opꢀonal ꢀming adjustment
5. Light/dark operate switch
1
2
3
Wiring Diagrams
Sensors with Aꢁached Cable and Sensors with Quick-Disconnect 4-Pin Mini (model suffix Q)
1
24-250V ac or 12-250V dc*
3
2
Isolated
Solid-state
SPST Switch
4
*NOTE: Connection of dc power is without regard to polarity.
Quick disconnect (QD) wiring diagrams are funcꢀonally idenꢀcal.
Emiꢁers with Aꢁached Cable
Emiꢁers with Quick-Disconnect 3-Pin Mini
brown
blue
brown
24–250 V ac or 12–250 V dc*
24–250 V ac or 12–250 V dc*
blue
black
*Connecꢀon of dc power is without regard to polarity.
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 53999 Rev. D
Q45BW13 Series Sensors
Speciꢃcaꢀons
Supply Voltage and Current
Repeatability
Opposed mode: 0.25 milliseconds
Universal voltage: 24 to 250 V ac, 50/60 Hz or 12 to 250 V dc (1.5 waꢄs
maximum)
All other sensing modes: 0.5 milliseconds
Response ꢀme and repeatability specificaꢀons are independent of signal
strength.
Supply Protecꢀon Circuitry
Protected against transient voltages
DC wiring is without regard to polarity
Adjustments
Light/Dark Operate select switch; and mulꢀ-turn Sensiꢀvity control on top of
Output Conꢃguraꢀon
®
sensor beneath a transparent o-ring-sealed Lexan cover, allows precise
All models except emiꢄers: Opꢀcally isolated SPST solid-state switch
sensiꢀvity seꢃng (turn clockwise to increase gain). Opꢀonal logic and logic/
display modules have adjustable ꢀming funcꢀons
Output Raꢀng
250 V ac, 250 V dc, 300 mA
Indicators
®
Output saturaꢀon voltage: 3 V at 300 mA, 2 V at 15 mA
Off-state leakage current: <50 microamps
Inrush current: 1 amp for 20 milliseconds, non-repeꢀꢀve
Indicator LEDs are clearly visible beneath a raised transparent Lexan dome on
top of the sensor.
Power (green) LED lights whenever 24 to 250V ac, or 12 to 250V dc power is
applied
Output Protecꢀon Circuitry
™
Signal (red) AID System LED lights whenever the sensor sees its modulated
Protected against false pulse on power-up
light source, and pulses at a rate proporꢀonal to the strength of the received
light signal
Output Response Time
Load (amber) LED lights whenever the output relay is energized
Opꢀonal 7-element LED signal strength display module
Opposed mode: 2 milliseconds on, 1 millisecond off
All other sensing modes: 2 milliseconds on/off
Construcꢀon
Note: 100 millisecond delay on power-up. Output
is non-conducꢀng during this ꢀme.
Molded reinforced thermoplasꢀc polyester housing, o-ring-sealed transparent
polycarbonate cover, molded acrylic lenses, and stainless steel hardware. Q45s
are designed to withstand 1200 psi washdown. The base of cabled models has
a 1/20-in NPS integral internal conduit thread.
Required Overcurrent Protecꢀon
Environmental Raꢀng
WARNING: Electrical connecꢀons must be made
by qualified personnel in accordance with local
and naꢀonal electrical codes and regulaꢀons.
NEMA 6P, IEC IP67
Connecꢀons
2 m (6.5 ꢂ) unterminated PVC-jacketed cable or 9 m (30 ꢂ) unterminated PVC-
jacketed cable, or Mini quick-disconnect (QD) fiꢃngs are available (“Q”- suffix
models). QD cables are ordered separately.
Overcurrent protecꢀon is required to be provided by end product applicaꢀon
per the supplied table.
Overcurrent protecꢀon may be provided with external fusing or via Current
Limiꢀng, Class 2 Power Supply.
Operaꢀng Condiꢀons
Supply wiring leads < 24 AWG shall not be spliced.
For addiꢀonal product support, go to www.bannerengineering.com.
–25 °C to +55 °C (−13 °F to +131 °F)
90% at +50 °C maximum relaꢀve humidity (non-condensing)
Applicaꢀon Notes
Supply Wiring (AWG)
Required Overcurrent Protecꢀon (Amps)
Opꢀonal output ꢀming modules are available. See page 10 for more
20
22
24
26
28
30
5.0
3.0
2.0
1.0
0.8
0.5
informaꢀon.
Output is not short-circuit protected. Exercise care when making wiring
connecꢀons.
Cerꢀꢃcaꢀons
P/N 53999 Rev. D
www.bannerengineering.com - Tel: +1-763-544-3164
5
Q45BW13 Series Sensors
Dimensions
Opposed, Retro, and Diffuse Sensing Modes (Model Suffix E, R, D, DL, DX, LP, and LV)
Cabled Models
Quick-Disconnect Models
54.1 mm
(2.13")
44.5 mm
(1.75")
Lens Centerline
50.8 mm
(2.00")
69.0 mm
(2.72")
6.4 mm (0.25")
87.6 mm
(3.45")
4.5 mm (#10) Screw
Clearance (2)
7.1 mm
(0.28")
30.0 mm
(1.18")
Internal Thread
(1/2–14NPSM)
ø 6.1 (0.24")
External Thread
M30 X 1.5
2m (6.5') Cable
External thread (M30 x 1.5)
hex nut supplied
14 mm (0.6")
Mini-style QD Connector
Convergent Sensor Models
(CV and CV4)
Glass Fiber Opꢀc Models
Plasꢀc Fiber Opꢀc Models
(FP)
(F and FV)
60.5 mm
(2.38")
61.7 mm
(2.43")
59.9 mm
(2.36")
6
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 53999 Rev. D
Q45BW13 Series Sensors
Accessories
Cordsets
3-Pin Mini-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
MBCC-306
1.83 m (6.5 ꢂ)
3.66 m (12 ꢂ)
1
52 Typ.
7/8-16UN-2B
ø 25.5
MBCC-312
2
3
Straight
1 = Black
2 = Brown
3 = Blue
MBCC-330
9.14 m (30 ꢂ)
4-Pin Mini-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
MBCC-406
1.83 m (6 ꢂ)
3.66 m (12 ꢂ)
4
3
2
1
MBCC-412
52 Typ.
7/8-16UN-2B
ø 25.5
Straight
1 = Brown
2 = White
3 = Blue
MBCC-430
9.14 m (30 ꢂ)
4 = Black
Retroreꢂecꢀve Targets
Banner offers a wide selecꢀon of high-quality retroreꢁecꢀve targets. See
www.bannerengineering.com for complete informaꢀon.
Note: Polarized sensors require corner cube type
retroreꢁecꢀve targets. Non-polarized sensors may use any
retroreꢁecꢀve target.
Brackets
SMB30C
56
SMB30MM
•
12-ga. stainless steel bracket
with curved mounꢀng slots for
versaꢀle orientaꢀon
Clearance for M6 (¼ in)
hardware
Mounꢀng hole for 30 mm
sensor
•
30 mm split clamp, black PBT
bracket
Stainless steel mounꢀng
hardware included
Mounꢀng hole for 30 mm
57
70
A
B
66
13
•
•
C
•
•
57
B
sensor
A
Hole center spacing: A=ø 45
Hole size: B=ø 27.2
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
P/N 53999 Rev. D
www.bannerengineering.com - Tel: +1-763-544-3164
7
Q45BW13 Series Sensors
SMB30SC
67
•
Swivel bracket with 30 mm
mounꢀng hole for sensor
B
•
•
Black reinforced thermoplasꢀc
58
polyester
Stainless steel mounꢀng and
swivel locking hardware
included
29
A
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
Output Timing Logic and Signal Strength Display Modules
Q45 sensors easily accept the addiꢀon of output ꢀming logic and signal strength display funcꢀons. Display modules have a seven-
™
element display that gives a more precise indicaꢀon of excess gain than does the AID system LED that is standard on Q45 sensors. The
modules listed below may be used with all Q45BW13 sensors. Refer to the module's datasheet for more informaꢀon.
Models
45LM58
45LM58D
45LMD
Logic and/or Display Funcꢀon
Programmable output ꢀming logic
Programmable output ꢀming logic plus signal strength display
Signal strength display only (no ꢀming funcꢀon)
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture which, at the ꢀme it is returned to the factory, is found to have been defecꢀve during the warranty period. This warranty does not cover
damage or liability for misuse, abuse, or the improper applicaꢀon or installaꢀon of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discreꢀon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY
OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT
DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaꢀons or liabiliꢀes relaꢀng to any product previously
manufactured by Banner Engineering Corp. Any misuse, abuse, or improper applicaꢀon or installaꢀon of this product or use of the product for personal protecꢀon applicaꢀons when the
product is idenꢀfied as not intended for such purposes will void the product warranty. Any modificaꢀons to this product without prior express approval by Banner Engineering Corp will void the
product warranꢀes. All specificaꢀons published in this document are subject to change; Banner reserves the right to modify product specificaꢀons or update documentaꢀon at any ꢀme.
Specificaꢀons and product informaꢀon in English supersede that which is provided in any other language. For the most recent version of any documentaꢀon, refer to:
www.bannerengineering.com.
©
Banner Engineering Corp. All rights reserved
相关型号:
©2020 ICPDF网 联系我们和版权申明