ATC18 [ATMEL]
Embedded ASIC Memory Cell; 嵌入式ASIC内存单元
| 型号： | ATC18 |
| 厂家： | 
ATMEL |
| 描述： | Embedded ASIC Memory Cell |
| 文件： | 总5页 (文件大小：431K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Features
• 64K x 32-bit Flash Embedded Memory Cell
• Fast Read Access Time
– Random Access Time: 70 ns Worst Case (Process, Voltage, Temperature)
– Page Access Time: 40 ns Worst Case (Process, Voltage, Temperature)
• Single Supply Voltage: 1.8V 10%
• Page Program Operation
– 1024 Pages (64 Words/Page)
– Internal Data Latches For 64 Words
– Read Capability During Data Load
• Program Cycle Time: 4 ms per Page Including Auto-erase
• Full Chip Erase Available in 10 ms
• rdybsyn Signal For End of Program Detection
• Very Low Power Dissipation
EmbeddedASIC
Memory Cell
– 8 mA Active Current in Write and Erase
– 4 mA Active Current in Random Read
– 30 µA Stand-by Current
ATC18
• High Reliability CMOS Technology
– Typical Endurance: 100K Write/Word
– Data Retention: 10 Years
• Erased State (Charged Gate) Is a Logic “1”
64K x 32-bit
Low-power
Flash
Description
The 64K x 32-bit cell is an embedded 2-Mbit Flash electrically erasable and program-
mable read only memory with a power supply of 1.8V 10%. The memory is organized
as 1024 pages of 64 32-bit words each. The device uses the Atmel ATC18 0.18 µm sil-
icon process. For easy reprogrammability, it does not require a high input voltage for
programming: the embedded Flash can be operated with a single 1.8V 10% power
supply.
Advance
Information
Re-programming the cell is performed on a page basis: the words to be written (from a
minimum of 1 word to a maximum of 64 words) are loaded into the device and then
simultaneously written into the targeted page after the full page has been erased dur-
ing the auto-erase phase. 2 ms are necessary to erase the page, followed by 2 ms to
write the words, independent of the number of words that are written in parallel into
the targeted page. Thus the write time after the auto-erase varies from a maximum of
2 ms per word if only 1 word is written to a minimum of 32 µs per word if the entire
page is written at a time. Memory read is allowed during data loading and forbidden
once programming has started. The signal rdybsyn pulses low at the beginning of the
program cycle to indicate that the memory is not ready for a read operation. Program-
ming the entire memory can be done using a full chip erase followed by 1024 page
write without auto-erase. Compared to full-memory programming using auto-erase on
each page, the programming time is reduced by half. At the end of each program
cycle, the rdybsyn signal pulses high to indicate that programming is completed and
the memory available for a new program or read cycle. Reading data out of the device
can be done in an asynchronous and random manner, with 70 ns access time.
Rev. 2680A–CASIC–11/02
DC and AC Operating
Range
Conditions are:
•
Operating temperature: -40°C to 85°C
Table 1. Parameters
Symbol
VDD
Parameter
Min
Typ
Max
2.0
70
Units
ns
Power Supply
1.6
1.8
tACC
Read Access Time
Page Access Time
Write Cycle Time(1)
tBACC
tWC
Note:
40
4
ms
1. The max value includes auto-erase.
Table 2. DC Characteristics
Symbol
Parameter
Condition
Max
ISB
Standby Current
VDD = 2.0V
30 uA
Random Read:
DD = 2.0V, 10 MHz
Write:
DD = 2.0V
4.0 mA
V
ICC
Active Current
8.0 mA
V
2
ATC18 64K x 32-bit Low-power Flash
2680A–CASIC–11/02
ATC18 64K x 32-bit Low-power Flash
3
2680A–CASIC–11/02
4
ATC18 64K x 32-bit Low-power Flash
2680A–CASIC–11/02
Atmel Headquarters
Atmel Operations
Corporate Headquarters
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 487-2600
Memory
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
TEL (49) 71-31-67-0
FAX (49) 71-31-67-2340
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 436-4314
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131
TEL 1(408) 441-0311
FAX 1(408) 436-4314
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL 1(719) 576-3300
FAX 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
TEL (41) 26-426-5555
FAX (41) 26-426-5500
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
TEL (33) 2-40-18-18-18
FAX (33) 2-40-18-19-60
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimhatsui
East Kowloon
BP 123
38521 Saint-Egreve Cedex, France
TEL (33) 4-76-58-30-00
FAX (33) 4-76-58-34-80
ASIC/ASSP/Smart Cards
Zone Industrielle
Hong Kong
TEL (852) 2721-9778
FAX (852) 2722-1369
13106 Rousset Cedex, France
TEL (33) 4-42-53-60-00
FAX (33) 4-42-53-60-01
Japan
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL 1(719) 576-3300
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
FAX 1(719) 540-1759
TEL (81) 3-3523-3551
FAX (81) 3-3523-7581
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
TEL (44) 1355-803-000
FAX (44) 1355-242-743
e-mail
literature@atmel.com
Web Site
http://www.atmel.com
© Atmel Corporation 2002.
Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty
which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors
which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does
not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted
by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical
components in life support devices or systems.
ATMEL® is the registered trademark of Atmel.
Other terms and product names may be the trademarks of others.
Printed on recycled paper.
2680A–CASIC–11/02 0M
相关型号：
©2020 ICPDF网 联系我们和版权申明