AT25FS040N-SU27-T [ATMEL]
Flash, 512KX8, PDSO8, 0.150 INCH, LEAD FREE, PLASTIC, MS-012AA, SOIC-8;型号: | AT25FS040N-SU27-T |
厂家: | ATMEL |
描述: | Flash, 512KX8, PDSO8, 0.150 INCH, LEAD FREE, PLASTIC, MS-012AA, SOIC-8 时钟 ATM 异步传输模式 光电二极管 内存集成电路 |
文件: | 总22页 (文件大小:389K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Features
• Serial Peripheral Interface (SPI) Compatible
• Supports SPI Modes 0 (0,0) and 3 (1,1)
– Datasheet describes Mode 0 Operation
• 50 MHz Clock Rate
• Byte Mode and Page Mode Program (1 to 256 Bytes) Operations
• Sector/Block/Page Architecture
– Sixteen 256 byte Pages per Sector
– Sixteen 4 Kbyte Sectors per Block
– Eight uniform 64 Kbyte Blocks
• Self-timed Sector, Block and Chip Erase
• Product Identification Mode with JEDEC Standard
• Low-voltage Operation
High Speed
Small Sectored
SPI Flash
Memory
4M (524,288 x 8)
– 2.7V (VCC = 2.7V to 3.6V)
• Hardware and Software Write Protection
– Device protection with Write Protect (WP) Pin
– Write Enable and Write Disable Instructions
– Software Write Protection:
Upper 1/64, 1/32, 1/16, 1/8, 1/4, 1/2 or Entire Array
• Flexible Op Codes for Maximum Compatibility
• Self-timed Program Cycle
– 30 µs/Byte Typical
• Single Cycle Reprogramming (Erase and Program) for Status Register
• High Reliability
– Endurance: 10,000 Write Cycles Typical
• 8-lead JEDEC 150mil SOIC and 8-lead Ultra Thin Small Array Package (SAP)
AT25FS040
Description
The AT25FS040 provides 4,194,304 bits of serial reprogrammable Flash memory
organized as 524,288 words of 8 bits each. The device is optimized for use in many
industrial and commercial applications where low-power and low-voltage operation
are essential. The AT25FS040 is available in a space-saving 8-lead JEDEC SOIC and
8-lead Ultra Thin SAP packages.
Advance
Information
Table 1. Pin Configuration
Pin Name
CS
Function
Chip Select
8-lead JEDEC SOIC
SCK
SI
Serial Data Clock
Serial Data Input
Serial Data Output
Ground
CS
SO
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
WP
SO
GND
GND
VCC
WP
Power Supply
Write Protect
8-lead SAP
___
Suspends Serial
Input
VCC 8
1 CS
_____
HOLD
HOLD 7
2 SO
___
SCK 6
SI 5
3 WP
4 GND
Bottom View
5107C–SFLSH–3/06
The AT25FS040 is enabled through the Chip Select pin (CS) and accessed via a 3-wire
interface consisting of Serial Data Input (SI), Serial Data Output (SO), and Serial Clock
(SCK). All write cycles are completely self-timed.
BLOCK WRITE protection for upper 1/64, 1/32, 1/16, 1/8, 1/4, 1/2 or the entire memory
array is enabled by programming the status register. Separate write enable and write
disable instructions are provided for additional data protection. Hardware data protec-
tion is provided via the WP pin to protect against inadvertent write attempts to the status
register. The HOLD pin may be used to suspend any serial communication without
resetting the serial sequence.
Absolute Maximum Ratings*
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Operating Temperature....................................–40°C to +85°C
Storage Temperature.....................................–65°C to +150°C
Voltage on Any Pin
with Respect to Ground....................................–1.0V to +5.0V
Maximum Operating Voltage ............................................ 4.2V
DC Output Current........................................................ 5.0 mA
Figure 1. Block Diagram
524,288x8
2
AT25FS040
5107C–SFLSH–3/06
AT25FS040
Table 2. Pin Capacitance(1)
Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +3.6V (unless otherwise noted)
Symbol
COUT
CIN
Test Conditions
Max
8
Units
pF
Conditions
VOUT = 0V
VIN = 0V
Output Capacitance (SO)
Input Capacitance (CS, SCK, SI, WP, HOLD)
6
pF
Note:
1. This parameter is characterized and is not 100% tested.
Table 3. DC Characteristics (Preliminary – Subject to Change)
Applicable over recommended operating range from: TAI = –40°C to +85°C, VCC = +2.7V to +3.6V,
AC = 0°C to +70°C, VCC = +2.7V to +3.6V (unless otherwise noted)
T
Symbol
VCC
ICC1
ICC2
ISB
Parameter
Test Condition
Min
Typ
Max
3.6
Units
V
Supply Voltage
Supply Current
Supply Current
Standby Current
Input Leakage
2.7
VCC = 3.6V at 20 MHz, SO = Open Read
VCC = 3.6V at 20 MHz, SO = Open Write
VCC = 2.7V, CS = VCC
10.0
15.0
2.0
17.0
mA
mA
µA
µA
µA
V
45.0
10.0
IIL
VIN = 0V to VCC
-3.0
-3.0
3.0
IOL
Output Leakage
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
VIN = 0V to VCC, TAC = 0°C to 70°C
3.0
(1)
VIL
-0.6
VCC x 0.3
VCC + 0.5
0.2
(1)
VIH
VCC x 0.7
V
VOL
VOH
2.7V ≤ VCC ≤ 3.6V
IOL = 0.15 mA
IOH = -100 µA
V
VCC - 0.2
V
Note:
1. VIL and VIH max are reference only and are not tested.
3
5107C–SFLSH–3/06
Table 4. AC Characteristics (Preliminary – Subject to Change)
Applicable over recommended operating range from TA = –40°C to +85°C, VCC = +2.7V to +3.6V
CL = 1 TTL Gate and 30 pF (unless otherwise noted)
Symbol
Parameter
Min
Typ
Max
50
5
Units
fSCK
SCK Clock Frequency
Input Rise Time
0
MHz
tRI
ns
tFI
Input Fall Time
5
ns
tWH
SCK High Time
9
9
ns
tWL
SCK Low Time
ns
tCS
CS High Time
100
5
ns
tCSS
CS Setup Time
ns
tCSH
CS Hold Time
5
ns
tSU
Data In Setup Time
Data In Hold Time
Hold Setup Time
5
ns
tH
5
ns
tHD
5
ns
tCD
Hold Hold Time
5
ns
tV
Output Valid
9
ns
tHO
Output Hold Time
Hold to Output Low Z
Hold to Output High Z
Output Disable Time
Erase Cycle Time per Sector/Block
Status Register Write Cycle Time
Byte Program Cycle Time(1)
0
ns
tLZ
9
9
ns
tHZ
ns
tDIS
9
ns
tEC
1.1
60
50
s
tSR
ms
tBPC
30
µs
Endurance(2)
10K
Write Cycles(3)
Notes: 1. The programming time for n bytes will be equal to n x tBPC
.
2. This parameter is characterized at 3.0V.
3. One write cycle consists of erasing a sector, followed by programming the same sector.
4
AT25FS040
5107C–SFLSH–3/06
AT25FS040
Serial Interface
Description
MASTER: The device that generates the serial clock.
SLAVE: Because the Serial Clock pin (SCK) is always an input, the AT25FS040 always
operates as a slave.
TRANSMITTER/RECEIVER: The AT25FS040 has separate pins designated for data
transmission (SO) and reception (SI).
MSB: The Most Significant Bit (MSB) is the first bit transmitted and received.
SERIAL OP-CODE: After the device is selected with CS going low, the first byte will be
received. This byte contains the op-code that defines the operations to be performed.
INVALID OP-CODE: If an invalid op-code is received, no data will be shifted into the
AT25FS040, and the serial output pin (SO) will remain in a high impedance state until
the falling edge of CS is detected again. This will reinitialize the serial communication.
CHIP SELECT: The AT25FS040 is selected when the CS pin is low. When the device is
not selected, data will not be accepted via the SI pin, and the serial output pin (SO) will
remain in a high impedance state.
HOLD: The HOLD pin is used in conjunction with the CS pin to select the AT25FS040.
When the device is selected and a serial sequence is underway, HOLD can be used to
pause the serial communication with the master device without resetting the serial
sequence. To pause, the HOLD pin must be brought low while the SCK pin is low. To
resume serial communication, the HOLD pin is brought high while the SCK pin is low
(SCK may still toggle during HOLD). Inputs to the SI pin will be ignored while the SO pin
is in the high impedance state.
WRITE PROTECT: The AT25FS040 has a write lockout feature that can be activated by
asserting the write protect pin (WP). When the lockout feature is activated, locked-out
sectors will be READ only. The write protect pin will allow normal read/write operations
when held high. When the WP is brought low and WPEN bit is “1”, all write operations to
the status register are inhibited. WP going low while CS is still low will interrupt a write to
the status register. If the internal status register write cycle has already been initiated,
WP going low will have no effect on any write operation to the status register. The WP
pin function is blocked when the WPEN bit in the status register is “0”. This will allow the
user to install the AT25FS040 in a system with the WP pin tied to ground and still be
able to write to the status register. All WP pin functions are enabled when the WPEN bit
is set to “1”.
5
5107C–SFLSH–3/06
Figure 2. SPI Serial Interface
MASTER:
MICROCONTROLLER
SLAVE:
AT25FS040
SI
DATA OUT (MOSI)
SO
DATA IN (MISO)
SERIAL CLOCK (SPI CK)
SCK
CS
SS0
SS1
SS2
SS3
SI
SO
SCK
CS
SI
SO
SCK
CS
SI
SO
SCK
CS
6
AT25FS040
5107C–SFLSH–3/06
AT25FS040
Functional
Description
The AT25FS040 is designed to interface directly with the synchronous serial peripheral
interface (SPI) of the 6800 type series of microcontrollers.
The AT25FS040 utilizes an 8-bit instruction register. The list of instructions and their
operation codes are contained in Table 5. All instructions, addresses, and data are
transferred with the MSB first and start with a high-to-low transition.
Write is defined as program and/or erase in this specification. The following commands,
PROGRAM, SECTOR ERASE, BLOCK ERASE, CHIP ERASE, and WRSR are write
instructions for AT25FS040.
Table 5. Instruction Set for the AT25FS040
Instruction Name
One Byte OpCode
Operation
Binary
Hex
WREN
WRDI
0000 X110
0000 X100
0000 X101
0000 X001
0000 0011
0000 1011
06
04
05
01
03
0B
Set Write Enable Latch
Reset Write Enable Latch
Read Status Register
RDSR
WRSR
READ
Write Status Register
Read Data from Memory Array
FAST READ
Read Data from Memory Array (with
dummy cycles)
PROGRAM
0000 X010
0010 0000
1101 0111
0101 0010
1101 1000
0110 0000
1100 0111
1001 1111
1010 1011
02
20
D7
52
D8
60
C7
9F
AB
Program Data Into Memory Array
Erase One 4kbyte Sector in Memory Array
SECTOR ERASE (1)
Erase One 64kbyte Block in Memory Array
Erase All Memory Array
BLOCK ERASE(1)
CHIP ERASE(1)
RDID(1)
Read Manufacturer and Product ID
Note:
1. Either one of the OP CODES will execute the instruction.
WRITE ENABLE (WREN): The device will power up in the write disable state when VCC
is applied. All write instructions must therefore be preceded by the WREN instruction.
WRITE DISABLE (WRDI): To protect the device against inadvertent writes, the WRDI
instruction disables all write commands. The WRDI instruction is independent of the sta-
tus of the WP pin.
READ STATUS REGISTER (RDSR): The RDSR instruction provides access to the sta-
tus register. The READY/BUSY and write enable status of the device can be determined
by the RDSR instruction. Similarly, the Block Write Protection bits indicate the extent of
7
5107C–SFLSH–3/06
protection employed. These bits are set by using the WRSR instruction. During internal
write cycles, all other commands will be ignored except the RDSR instruction.
Table 6. Status Register Format
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WPEN
BP4
BP3
BP2
BP1
BP0
WEN
RDY
Table 7. Read Status Register Bit Definition
Bit
Definition
Bit 0 = 0 (RDY) indicates the device is READY. Bit 0 = 1 indicates the
write cycle is in progress.
Bit 0 (RDY)
Bit 1 = 0 indicates the device is not WRITE ENABLED. Bit 1 = 1 indicates
the device is WRITE ENABLED.
Bit 1 (WEN)
Bit 2 (BP0)
Bit 3 (BP1)
Bit 4 (BP2)
Bit 5 (BP3)
Bit 6 (BP4)
Bit 7 (WPEN)
See Table 9.
See Table 9.
See Table 9.
See Table 9.
See Table 9.
See Table 10.
Bits 0-7 are 1s during an internal write cycle.
READ PRODUCT ID (RDID): The RDID instruction allows the user to read the manufac-
turer ID byte followed by two device ID bytes. The manufacturer ID is assigned by
JEDEC and is 1Fh for Atmel (see Table 8). The first device ID byte indicates the mem-
ory type (66h=AT25FS040) followed by the device memory capacity byte (04h). For
maximum compatibility and flexibility, two RDID opcodes (9Fh and ABh) are supported
and will perform the same operation.
Table 8. Read Product ID (RDID)
Manufacturer ID
Device ID
Memory Type
66h
Memory Capacity
04h
1Fh
The device is first selected by driving Chip Select (CS) low then the RDID opcode is
shifted in on Serial In (SI) during rising edge of clock. The 24-bit Manufacturer and
Device Identification Codes stored in memory are clocked out on Serial Output (SO)
starting on the falling edge of clock (see Figure 15). If CS stays low after the last bit of
second device ID byte is shifted out, the manufacturer ID and 2 byte device ID will con-
tinue to be clocked out until CS goes high. The RDID sequence is terminated any time
CS is driven high and the device will go into standby mode.
WRITE STATUS REGISTER (WRSR): The WRSR instruction allows the user to select
one of eight levels of protection for the AT25FS040. The AT25FS040 is divided into
eight blocks where the top 1/64, 1/32, 1/16, 1/8, top quarter (1/4), top half (1/2), or all of
the memory blocks can be protected (locked out) from write. Any of the locked-out
blocks will therefore be READ only. The locked-out sector/block and the corresponding
status register control bits are shown in Table 9 on page 9.
8
AT25FS040
5107C–SFLSH–3/06
AT25FS040
The six bits, BP0, BP1, BP2, BP3, BP4 and WPEN, are nonvolatile cells that have the
same properties and functions as the regular memory cells.
Table 9. Sector/Block Write Protect Bits
Level
Status Register Bits
AT25FS040
BP4
BP3
BP2
BP1
BP0
Array Address
locked Out
Locked-out
Blocks
0(none)
1(1/64)
2(1/32)
3(1/16)
4(1/8)
0
0
1
1
x
x
x
x
0
1
0
1
x
x
x
x
0
0
0
0
0
0
0
1
0
0
0
0
0
1
1
x
0
0
0
0
1
0
1
x
None
None
07E000H - 07FFFFH
07C000H - 07FFFFH
078000H - 07FFFFH
070000H - 07FFFFH
060000H - 07FFFFH
040000H - 07FFFFH
000000H - 07FFFFH
Sector 15-16 of Block 8
Sector 13-16 of Block 8
Sector 9-16 of Block 8
All sectors of Block 8
5(1/4)
All Sectors of Block 7,8
All Sectors of Block 5,6,7,8
All Sectors of All Blocks (1-8)
6(1/2)
7(ALL)
Note:
1. x = don’t care
The WRSR instruction also allows the user to enable or disable the Write Protect (WP)
pin through the use of the Write Protect Enable (WPEN) bit. Hardware write protection is
enabled when the WP pin is low and the WPEN bit is “1”. Hardware write protection is
disabled when either the WP pin is high or the WPEN bit is “0.” When the device is hard-
ware write protected, writes to the Status Register, including the Block Protect bits and
the WPEN bit, and the locked-out sectors in the memory array are disabled. Write is
only allowed to sectors of the memory which are not locked out. The WRSR instruction
is self-timed to automatically erase and program BP0, BP1, BP2, BP3, BP4 and WPEN
bits. In order to write the status register, two separate instructions must be executed.
First, the device must be write enabled via the WREN instruction. Then, CS must be low
and the WRSR instruction and data for the six bits are entered. The WRSR write cycle
will begin once CS goes high. During the internal write cycle, all instructions will be
ignored except RDSR instructions. The AT25FS040 will automatically return to write dis-
able state at the completion of the WRSR cycle. The status register is factory
programmed to all 0’s.
Note:
When the WPEN bit is hardware write protected, it cannot be changed back to “0”, as
long as the WP pin is held low.
Table 10. WPEN Operation
WPEN
WP
X
WEN
ProtectedBlocks
Protected
UnprotectedBlocks
Protected
Status Register
Protected
Writable
0
0
1
1
X
X
0
1
0
1
0
1
X
Protected
Writable
Low
Low
High
High
Protected
Protected
Protected
Protected
Protected
Writable
Protected
Writable
Protected
Protected
Writable
Protected
9
5107C–SFLSH–3/06
READ (READ): The READ instruction sequence reads the memory array up to the max-
imum speed of 50MHz. Reading the AT25FS040 via the SO (Serial Output) pin requires
the following sequence. After the CS line is pulled low to select the device, the READ
instruction is clocked in on the SI line, followed by the byte address to be read. Upon
completion, any data on the SI line will be ignored. The data (D7-D0) at the specified
address is then shifted out onto the SO line (see Figure 8). If only one byte is to be read,
the CS line should be driven high after the least significant data bit. To continue read
operation and sequentially read subsequent byte addresses from the device by simply
keeping CS low and provide a clock signal. The device incorporates an internal address
counter that automatically increments to next byte address during sequential read oper-
ation. The READ instruction can be continued since the byte address is automatically
incremented and data will continue to be shifted out of the AT25FS040 until the highest
byte address is reached. When the last bit of the memory has been read, the device will
continue reading back at the beginning of the array (000000h) without delay. The data is
always output from the device with the most significant bit (MSB) of a byte first. The
READ sequence is terminated any time CS is driven high and the device will go into
standby mode.
FAST READ (FAST READ): The FAST READ instruction sequence reads the memory
array up to the maximum speed of 50MHz (same as standard READ sequence). The
FAST READ is an alternate command for the READ and allows for FAST READ instruc-
tion compatibility support. The difference between the two is FAST READ requires a
“dummy byte” and READ does not. Reading the AT25FS040 via the SO (Serial Output)
pin requires the following sequence. After the CS line is pulled low to select the device,
the FAST READ instruction is clocked in on the SI line, followed by the byte address to
be read and the dummy byte (the SO line output will be high Z state). Upon completion,
any data on the SI line will be ignored. The data (D7-D0) at the specified address is then
shifted out onto the SO line (see Figure 9). If only one byte is to be read, the CS line
should be driven high after the least significant data bit. To continue read operation and
sequentially read subsequent byte addresses from the device by simply keeping CS low
and provide a clock signal. The device incorporates an internal address counter that
automatically increments to next byte address during sequential read operation. The
FAST READ instruction can be continued since the byte address is automatically incre-
mented and data will continue to be shifted out of the AT25FS040 until the highest
address is reached. When the last bit of the memory has been read, the device will con-
tinue reading back at the beginning of the array (000000h) without delay. The data is
always output from the device with the most significant bit (MSB) of a byte first. The
FAST READ sequence is terminated any time CS is driven high and the device will go
into standby mode.
PROGRAM (PROGRAM): The PROGRAM instruction allows up to 256 data bytes to be
written to each page in the memory in one-operation changing data bits from a logic 1 to
0 state. The AT25FS040 memory array contains 524,288 programmable data bytes
internally organized into 256 bytes per page with a total of 2048 pages in the memory.
In order to program the AT25FS040, two separate instructions must be executed. First,
the device must be write enabled via the WREN instruction. Then the PROGRAM
instruction can be executed and requires the following sequence. After the CS line is
pulled low to select the device, the PROGRAM instruction is clocked in via the SI line
followed by the byte address (see Figure 10) and the data byte(s) to be programmed.
Programming will start after CS pin is brought high. Please note: The low to high transi-
tion of the CS pin must occur during the SCK low time immediately after clocking in the
D0 (LSB) data bit to initiate programming cycle. Also, a WREN instruction must precede
each and every PROGRAM instruction. The Ready/Busy status of the device can be
determined by initiating a RDSR instruction. If bit 0=1, the program cycle is still in
10
AT25FS040
5107C–SFLSH–3/06
AT25FS040
progress. If Bit 0=0, the programming cycle has ended. Only the RDSR instruction is
enabled during the programming cycle and all other opcode instructions are ignored
until programming cycle has completed.
A single PROGRAM instruction programs 1 to 256 consecutive bytes within a page if it
is not write protected. The starting byte address can be anywhere within the page.
When the end of the page is reached, the address will wrap around to the beginning of
the same page. If the data to be programmed is less than a full page, the data of all
other bytes on the same page will remain unchanged meaning that the unwritten
address locations within the page will not be changed. If more than 256 bytes of data
are provided, the address counter will roll over on the same page and the previous data
provided will be replaced. The same byte cannot be reprogrammed without erasing the
whole sector or block first. The AT25FS040 will automatically return to the write disable
state at the completion of the programming cycle.
Note:
If the device is not write enabled (WREN), the device will ignore the Write instruction and
will return to the standby state when CS is brought high. A new CS falling edge is
required to re-initiate the serial communication.
Table 11. Address Key
Address
AT25FS040
A18 - A0
AN
Don’t Care Bits
A23 - A19
ERASE OPERATION: The AT25FS040 memory array is internally organized into uni-
form 4K byte sectors or uniform 64K byte uniform blocks (see Table 12). Before data can
be reprogrammed, the sector or block that contains the data must be erased first. In
order to erase the AT25FS040, there are three flexible erase instructions that can be
executed as follows: SECTOR ERASE, BLOCK ERASE and CHIP ERASE instructions.
A SECTOR ERASE instruction allows erasing any individual 4K sector without changing
data in rest of memory. The BLOCK ERASE instruction allows erasing any individual
block and CHIP ERASE allows erasing the entire memory array.
SECTOR ERASE (SECTOR ERASE): The SECTOR ERASE instruction sets all 4K
bytes in the selected sector to logic 1 or erased state. In order to sector erase the
AT25FS040, two separate instructions must be executed. First, the device must be write
enabled via the WREN instruction. Then the SECTOR ERASE instruction can be exe-
cuted and will erase every byte in the selected sector if the sector is not locked out. The
sector address is automatically determined if any address within the sector is selected
(see Figure 12). The SECTOR ERASE instruction is internally controlled and self timed
to completion. During this time, all commands will be ignored except RDSR instruction.
The progress or completion of the erase operation can be determined by reading
ready/busy bit (bit 0) through RDSR instruction. If Bit 0=1, sector erase cycle is in
progress. If Bit 0=0, the erase operation has been completed. The AT25FS040 will auto-
11
5107C–SFLSH–3/06
matically return to the write disable state at the completion of the SECTOR ERASE
cycle.
Table 12. Sector and Block Address
07FFFFH
Sector 16
Block 8
07F000H
07EFFFH
07E000H
07DFFFH
07D000H
07CFFFH
07C000H
07BFFFH
07B000H
07AFFFH
07A000H
079FFFH
079000H
078FFFH
078000H
077FFFH
077000H
076FFFH
076000H
075FFFH
075000H
074FFFH
074000H
073FFFH
073000H
072FFFH
072000H
071FFFH
071000H
070FFFH
070000H
06FFFFH
060000H
1/64
Sector 15
Sector 14
Sector 13
Sector 12
Sector 11
Sector 10
Sector 9
Sector 8
Sector 7
Sector 6
Sector 5
Sector 4
Sector 3
Sector 2
Sector 1
1/32
1/16
1/8
Block 7
12
AT25FS040
5107C–SFLSH–3/06
AT25FS040
Table 12. Sector and Block Address (Continued)
05FFFFH
050000H
04FFFFH
040000H
03FFFFH
030000H
02FFFFH
020000H
01FFFFH
010000H
00FFFFH
000000H
Block 6
Block 5
Block 4
Block 3
Block 2
Block 1
BLOCK ERASE (BLOCK ERASE): The BLOCK ERASE instruction sets all 64K bytes
in the selected block to logic 1 or erased state. In order to block erase the AT25FS040,
two separate instructions must be executed. First, the device must be write enabled via
the WREN instruction. Then the BLOCK ERASE instruction can be executed and will
erase every byte in the selected block if the block is not locked out. The block address is
automatically determined if any address within the block is selected (see Figure 13). The
BLOCK ERASE instruction is internally controlled and self timed to completion. During
this time, all commands will be ignored except RDSR instruction. The progress or com-
pletion of the erase operation can be determined by reading ready/busy bit (bit 0)
through RDSR instruction. If Bit 0=1, block erase cycle is in progress. If Bit0=0, the
erase operation has been completed. The AT25FS040 will automatically return to the
write disable state at the completion of the BLOCK ERASE cycle.
CHIP ERASE (CHIP ERASE): As an alternative to the SECTOR ERASE/BLOCK
ERASE, the CHIP ERASE instruction will erase every byte in all sectors that are not
locked out. First, the device must be write enabled via the WREN instruction. Then the
CHIP ERASE instruction can be executed. The CHIP ERASE instruction is internally
controlled; it will automatically be timed to completion. The CHIP ERASE cycle time typ-
ically is 8 seconds. During the internal erase cycle, all instructions will be ignored except
RDSR. The AT25FS040 will automatically return to the write disable state at the comple-
tion of the CHIP ERASE cycle.
13
5107C–SFLSH–3/06
Timing Diagrams (for SPI Mode 0 (0, 0))
Figure 3. Synchronous Data Timing
tCS
VIH
CS
VIL
tCSH
tCSS
VIH
tWH
tWL
SCK
VIL
tSU
tH
VIH
VIL
SI
VALID IN
tHO
tDIS
tV
VOH
VOL
HI-Z
HI-Z
SO
Figure 4. WREN Timing
Figure 5. WRDI Timing
14
AT25FS040
5107C–SFLSH–3/06
AT25FS040
Figure 6. RDSR Timing
CS
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
SCK
SI
RDSR OP-CODE
DATA OUT
HIGH IMPEDANCE
7
6
5
4
3
2
1
0
SO
MSB
Figure 7. WRSR Timing
WRSR OP-CODE
Figure 8. READ Timing
CS
0
1
2
3
4
5
6
7
8
9 10 11 28 29 30 31 32 33 34 35 36 37 38 39
SCK
3-BYTE ADDRESS
...
SI
INSTRUCTION
23 22 21
3
2
1
0
HIGH IMPEDANCE
SO
7
6
5
4
3
2
1
0
15
5107C–SFLSH–3/06
Figure 9. FAST READ Timing
CS
0
1
2
3
4
5
6
7
8
9 10 11 28 29 30 31 32 33 34 35 36 37 38 39
SCK
SI
3-BYTE ADDRESS
...
INSTRUCTION
23 22 21
3
2
1
0
HIGH IMPEDANCE
SO
7
6
5
4
3
2
1
0
Figure 10. PROGRAM Timing
CS
0
1
2
3
4
5
6
7
8
9
10 11 28 29 30 31 32 33 34
SCK
SI
1st BYTE DATA-IN
256th BYTE DATA-IN
3-BYTE ADDRESS
PROGRAM OP-CODE
23 22 21
3
2
1
0
7
6
5
4
3
2
1
0
HIGH IMPEDANCE
SO
Figure 11. HOLD Timing
CS
tCD
tCD
SCK
tHD
tHD
HOLD
SO
tHZ
tLZ
16
AT25FS040
5107C–SFLSH–3/06
AT25FS040
Figure 12. SECTOR ERASE Timing
SECTOR ERASE OP-CODE
Figure 13. BLOCK ERASE Timing
BLOCK ERASE OP-CODE
17
5107C–SFLSH–3/06
Figure 14. CHIP ERASE Timing
CHIP ERASE OP-CODE
Figure 15. RDID Timing
CS
4
8
1
2
3
5
6
9 10
0
7
11 12 13 14 15 16 17 18
29 30 31
28
SCK
SI
RDID OP-CODE
DATA OUT
3
HIGH IMPEDANCE
SO
Manufacturer Code (Atmel = 1Fh)
14
0
15
2
1
DEVICE IDENTIFICATION
18
AT25FS040
5107C–SFLSH–3/06
AT25FS040
Ordering Information
Ordering Code
Package
Operation Range
AT25FS040N-SU27-B(1)
AT25FS040N-SU27-T(2)
AT25FS040Y7-YH27-T(2)
8S1
8S1
8Y7
Lead-Free/Halogen-Free/
Industrial Temperature
(–40°C to 85°C)
Notes: 1. “B” denotes bulk.
2. “T” denotes tape and reel, SOIC quantity is 4,000 per reel and SAP quantity is 5,000 per reel.
Package Type
8-lead, 0.150” Wide, Plastic Gull Wing Small outline (JEDEC SOIC)
8-lead, 6.00 mm x 4.90 mm Body, Ultra Thin, Dual Footprint, Non-leaded, Small Array Package (SAP)
Options
8S1
8Y7
–2.7
Low Voltage (2.7V to 3.6V)
19
5107C–SFLSH–3/06
Package Information
8S1 – JEDEC SOIC
C
1
E
E1
L
N
∅
Top View
End View
e
B
COMMON DIMENSIONS
(Unit of Measure = mm)
A
MIN
1.35
0.10
MAX
1.75
0.25
NOM
NOTE
SYMBOL
A1
A
–
–
A1
b
0.31
0.17
4.80
3.81
5.79
–
0.51
0.25
5.00
3.99
6.20
C
D
E1
E
–
–
D
–
–
Side View
e
1.27 BSC
L
0.40
0°
–
–
1.27
∅
8°
Note:
These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc.
10/7/03
REV.
TITLE
DRAWING NO.
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing
8S1
B
R
Small Outline (JEDEC SOIC)
20
AT25FS040
5107C–SFLSH–3/06
AT25FS040
8Y7 – UT SAP
PIN 1 INDEX AREA
A
PIN 1 ID
D
E1
L
A1
E
b
e
e1
A
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN
–
MAX
0.60
0.05
6.20
5.10
3.50
4.10
0.45
NOM
–
NOTE
A
A1
D
0.00
5.80
4.70
3.30
3.90
0.35
–
6.00
E
4.90
D1
E1
b
3.40
4.00
0.40
e
1.27 TYP
3.81 REF
0.60
e1
L
0.50
0.70
10/13/05
TITLE
DRAWING NO.
REV.
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
8Y7, 8-lead (6.00 x 4.90 mm Body) Ultra-Thin SOIC Array
Package (UTSAP) Y7
8Y7
B
R
21
5107C–SFLSH–3/06
Atmel Corporation
Atmel Operations
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Memory
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
Regional Headquarters
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
ASIC/ASSP/Smart Cards
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© Atmel Corporation 2006. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are® and others, are registered trade-
marks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Printed on recycled paper.
5107C–SFLSH–3/06
相关型号:
AT25HP256-10CJ-1.8
EEPROM, 32KX8, Serial, CMOS, 6 X 5 MM, 1.04 MM HEIGHT, 1.27 MM PITCH, LAP-8
ATMEL
©2020 ICPDF网 联系我们和版权申明