MP39A [APEX]
POWER OPERATIONAL AMPLIFIER; 功率运算放大器
| 型号： | MP39A |
| 厂家： | 
CIRRUS LOGIC |
| 描述： | POWER OPERATIONAL AMPLIFIER |
| 文件： | 总4页 (文件大小：263K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
�ꢀꢁꢂꢃꢄꢀ�ꢂꢃꢅꢆꢇꢀꢈꢅꢉꢄꢅꢊ�ꢉꢇꢋꢇꢂꢃ
�ꢀꢁꢂꢃꢄꢃ�ꢀꢁꢂꢅꢃ
�
ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢁ
ꢆ
ꢇ
ꢃ
ꢈ
ꢃ
ꢉ
ꢊ
�ꢀꢀꢁꢂꢃꢃꢄꢄꢄꢅꢆꢁꢇꢈꢉꢊꢋꢌꢍꢀꢇꢋ�ꢅꢋꢍꢉꢎꢎꢎꢏꢐꢑꢑꢒꢎꢓꢔꢕꢖꢆꢁꢇꢈꢎꢎꢎꢏꢐꢑꢑꢒꢎꢓꢔꢕꢖꢗꢘꢙꢚ
FEATURES
• HIGH INTERNAL DISSIPATION — 125 Watts
• HIGH VOLTAGE, HIGH CURRENT — 100V, 10A
• HIGH SLEW RATE — 10V/µs
• 4 WIRE CURRENT LIMIT SENSING
• OPTIONAL BOOST VOLTAGE INPUTS
APPLICATIONS
• LINEAR AND ROTARY MOTOR DRIVES
• YOKE/MAGNETIC FIELD EXCITATION
• PROGRAMMABLE POWER SUPPLIES TO ±45V
• INDUSTRIAL AUDIO
30-pin DIP
PACKAGE STYLE CL
• PACKAGE OPTION - DIP10 - DUAL-IN-LINE
TYPICAL APPLICATION REF: APPLICATION NOTE 25
The high power bandwidth and high voltage output of the
MP39 allows driving ultra-sonic transducers via a resonant
circuit including the transducer and a matching transformer.
The load circuit appears resistive to the MP39.
DESCRIPTION
The MP39 is a cost-effective high voltage MOSFET power
operational amplifier constructed with surface mount com-
ponents on a thermally conductive but electrically isolated
substrate.
�
ꢀ
While the cost is low the MP39 offers many of the same
features and performance specifications found in much more
expensive hybrid power amplifiers.
ꢁꢂꢃꢄ
ꢒ
ꢒꢕꢊꢒꢙ
ꢁꢄꢋ
ꢁꢄꢓ
�
ꢆꢇꢈ�ꢉꢊ
ꢋꢌꢍꢅꢎ
ꢏ�ꢅꢄꢐ
ꢅ
ꢘꢃ
ꢕꢝ
The metal substrate allows the MP39 to dissipate power
up to 125 watts and its power supply voltages can range up
to +/- 50 Volts (100V total). Optional boost voltage inputs
allow the small signal portion of the amplifier to operate at
higher supply voltages than the high current output stage.
The amplifier is then biased to achieve close linear swings
to the supply rails at high current for extra efficient operation.
External compensation tailors performance to the user needs.
A four-wire sense technique allows current limiting without
the need to consider internal or external mili-ohm parasitic
resistance in the output line. An Iq pin is available which can
be used to shut off the quiescent current in the output stage.
The output stage then operates class C and lowers quiescent
power dissipation. This is useful in applications where output
crossover distortion is not important.
ꢕꢘ
ꢊꢅꢇꢅꢑ
ꢕꢙ
ꢁꢅꢇꢅꢑ
ꢊꢅꢍ
ꢌꢆꢈ
ꢑꢗꢘꢝ
ꢒꢂꢊꢒꢚ
ꢎꢎꢕ
�
ꢎꢇ
ꢁꢅꢍ
ꢎꢎꢒ
ꢙ
ꢅꢔ
ꢛ
ꢕꢂ
ꢎꢎ
ꢍꢎ
ꢊꢄꢋ
�
ꢎ
ꢊꢄꢓ
ꢕꢛ
ꢒꢜꢊꢕꢃ
ꢊꢂꢃꢄ
ꢈꢆꢍꢐꢏ
ꢈ�ꢉꢍꢋꢀꢌ�ꢑꢐ�
ꢆꢇꢈ�ꢉꢊꢋꢌꢍꢅꢎꢖꢉꢑꢗꢇꢅꢀꢅꢐ�
EXTERNAL CONNECTIONS
ꢢ
ꢢ
ꢂꢙ
ꢚꢙ
EQUIVALENT SCHEMATIC
ꢆ
ꢊ
ꢕ
ꢋ
ꢇ
ꢑ
ꢖ
ꢔ
ꢗ
ꢆꢏ ꢆꢆ ꢆꢊ ꢆꢕ ꢆꢋ
�
�ꢂ ꢍꢎꢘ
�ꢁ ꢍꢎꢘ
ꢍꢎꢏ
ꢔꢂ
ꢔ�
ꢉ�
ꢂ
ꢉꢂ
ꢔꢁ
ꢂꢃꢜꢝꢃꢁꢞꢁꢅꢟꢠꢀꢓꢞꢟꢈꢀꢞꢡ
�ꢀ
ꢍꢎꢘ
ꢕ�ꢖ
ꢕ�ꢗ
ꢊꢋꢌ
ꢕꢅ
ꢕꢁ
ꢕꢏ ꢊꢗ ꢊꢔ ꢊꢖ ꢊꢑ ꢊꢇ ꢊꢋ ꢊꢕ ꢊꢊ ꢊꢆ ꢊꢏ ꢆꢗ ꢆꢔ ꢆꢖ ꢆꢑ ꢆꢇ
ꢌ�
ꢔꢀ
ꢕꢀ
ꢉꢐꢂ
ꢉꢐ�
ꢀ
ꢄ
ꢕꢇ
ꢂꢀ ꢍꢒꢙꢚꢛ
ꢕꢃ
ꢑꢒꢙꢚꢛ
ꢂꢁ
ꢕꢄ
ꢢ
ꢢ
ꢔꢈ
ꢔꢇ
�ꢅ
�ꢄ
�ꢃ
ꢜꢝꢞ
ꢜꢝꢞ
ꢜꢝꢞ
ꢕꢈ
ꢔꢅ
ꢕ�ꢆꢗ
ꢁꢆ
ꢂꢇ
ꢑꢒꢋ
ꢕ�ꢆꢖ
ꢔ�ꢆ
ꢔꢄ
ꢔꢃ
* SEE "BYPASSING" PARAGRAPH
Phase Compensation
ꢍꢒꢋ
ꢕ��
ꢒꢓ ꢂꢅ
Gain
Cc
Rc
ꢔ��
1
≥ 3
≥ 10
470pF
220pF
100pF
100Ω
Short
Short
ꢕ�ꢂ
ꢂꢈ
ꢊꢋꢌ
ꢑꢎꢘ
ꢑꢎꢘ
ꢑꢎꢘ
ꢕ�ꢁ
ꢔ�ꢂ
�ꢈ
�ꢇ
ꢂꢆ
ꢕ�ꢀ
ꢉꢁ
ꢔ�ꢁ
ꢑꢎꢏ ꢂꢄ
APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL prodlit@apexmicrotech.com
1
ABSOLUTE MAXIMUM RATINGS
SPECIFICATIONS
MP39 • MP39A
SUPPLY VOLTAGE, +VS to –VS
BOOST VOLTAGE
100V
±VS ±20V
25A
125W
±20V
±VB
200°C
175°C
ABSOLUTE MAXIMUM RATINGS
OUTPUT CURRENT, within SOA
POWER DISSIPATION, internal
INPUT VOLTAGE, differential
INPUT VOLTAGE, common mode
TEMPERATURE, pin solder - 10s
TEMPERATURE, junction2
TEMPERATURE, storage
OPERATING TEMPERATURE RANGE, case
–40 to +105°C
–40 to +85°C
SPECIFICATIONS
MP39
TYP
MP39A
TYP
PARAMETER
TEST CONDITIONS1
MIN
MAX MIN
MAX
UNITS
INPUT
OFFSET VOLTAGE, initial
OFFSET VOLTAGE, vs. temperature
OFFSET VOLTAGE, vs. supply
OFFSET VOLTAGE, vs. power
BIAS CURRENT, initial
5
30
15
30
10
.01
10
1010
20
10
50
*
*
*
*
*
*
*
*
*
*
*
*
3
*
mV
µV/°C
µV/V
µV/W
pA
pA/V
pA
Ω
pF
V
dB
Full temperature range
Full temperature range
200
50
100
30
BIAS CURRENT, vs. supply
OFFSET CURRENT, initial
INPUT IMPEDANCE, DC
INPUT CAPACITANCE
COMMON MODE VOLTAGE RANGE Full temperature range
COMMON MODE REJECTION, DC
INPUT NOISE
±
±
±VB 15 ±VB 12
*
*
Full temp, range, V = ±20V
86
98
10
100kHz BW, RS = 1CKMΩ
µVrms
GAIN
OPEN LOOP, @15Hz
GAIN BANDWIDTH PRODUCT
POWER BANDWIDTH
Full temperature range, CC = 100pF
IO=10A
94
113
2
40
*
*
*
*
db
MHz
kHz
R =10Ω, VO =90V p-p
CCL = 100pF
PHASE MARGIN
Full temperature range
60
*
°
OUTPUT
±
±
±
VOLTAGE SWING
VOLTAGE SWING
SETTLING TIME to .1%
SLEW RATE
IO=10A
±V 8.8 ±V 6.0
*
*
*
*
*
V
V
µs
V/µs
nF
Ω
±VSS 6.8 ±VSS 1.1
±
±VB = ±VS ±10V, IO=10A
A =+1,10V step, R =4Ω
AVV= –10, CC= 100pLF
Full temperature range, AV=+1
2.5
10
10
4
*
*
CAPACITIVE LOAD
RESISTANCE
CURRENT, CONTINUOUS
*
*
10
11
A
POWER SUPPLY
VOLTAGE
CURRENT, quiescent, boost supply
CURRENT, quiescent, total
Full temperature range
±15
-40
±40
12
±50
22
26
*
*
*
*
*
V
mA
mA
THERMAL
RESISTANCE, AC, junction to case3
RESISTANCE, DC, junction to case
RESISTANCE4, junction to air
TEMPERATURE RANGE, case
Full temperature range, F>60Hz
Full temperature range, F<60Hz
Full temperature range
.9
1.2
*
*
°C/W
°C/W
°C/W
°C
*
Meets full range specification
85
*
NOTES:
*
1.
The specification of MP39A is identical to the specification for MP39 in applicable column to the left.
Unless otherwise noted: TC = 25°C, RC = 100Ω, CC = 470pF. DC input specifications are ± value given. Power supply voltage is
typical rating. ±VB = ±V .
2.
Long term operation atSthe maximum junction temperature will result in reduced product life. Derate internal power dissipation
to achieve high MTTF. For guidance, refer to the heatsink data sheet.
3.
4.
Rating applies if the output current alternates between both output transistors at a rate faster than 60 Hz.
The MP39 must be used with a heat sink or the quiescent power may drive the unit to junction temperatures higher than 175°C.
The MP39 is constructed from MOSFET transistors. ESD handling procedures must be observed.
CAUTION
2APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL prodlit@apexmicrotech.com
TYPICAL PERFORMANCE
GRAPHS
MP39 • MP39A
ꢋꢃꢏꢌꢁꢇꢈꢌꢁꢀꢊꢅꢄꢎ
�ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢅꢉꢊꢃꢁꢊꢅꢃꢄ
ꢉꢃꢀ
�ꢛꢀ
�ꢀꢀ
�ꢀ
�ꢀꢀ
�ꢀ
�
�ꢫꢆ
ꢞ
ꢬ
ꢈ
ꢭꢃ�ꢀ
ꢭꢃꢍꢮꢡꢢꢣ
ꢬꢃ
ꢆꢃ
�ꢀꢫꢆ
�ꢙꢀ
�ꢀꢀ
ꢥꢀ
ꢣꢀ
ꢛꢀ
ꢙꢀ
ꢀ
ꢭꢃꢥꢪ
ꢧꢋꢞꢄꢃ
�
ꢀꢁ�
ꢤꢀꢫꢩ
�ꢙꢤꢯꢒ
ꢥꢤꢯꢒ
ꢤꢀꢩ
ꢀꢁꢀ�
ꢙꢤꢯꢒ
ꢀꢁꢀꢀ�
ꢀꢁ�
�ꢏ
ꢐꢈꢎꢑꢊꢎꢌꢒꢓꢔꢃꢐꢃꢕꢖꢗꢘ
ꢀ
ꢙꢀ
ꢛꢀ
ꢣꢀ
ꢥꢀ
�ꢀꢀ
�ꢀꢀ
�ꢀꢏ
�ꢀꢀꢏ
�
�ꢀ
�ꢀꢀ
ꢒꢞꢆꢎꢃꢇꢎꢠꢝꢎꢈꢞꢇꢊꢈꢎꢔꢃꢇ ꢃꢕꢯꢒꢘ
ꢒ
ꢆꢊꢝꢝꢧꢓꢃꢳꢴꢃꢋꢊꢇꢝꢊꢇꢃꢄꢅꢐꢐꢎꢈꢎꢌꢇꢅꢞꢧꢔꢃꢬꢆꢡꢬꢋꢃꢕꢬꢘ
ꢋ�ꢀꢉꢌꢇꢁꢌꢉꢋꢃꢄꢉꢌ
ꢉꢂꢀꢍꢍꢇꢉꢅꢎꢄꢀꢍꢇꢁꢌꢉꢋꢃꢄꢉꢌ
ꢋꢃꢏꢌꢁꢇꢁꢌꢉꢋꢃꢄꢉꢌ
ꢀ
ꢡꢢꢀ
�ꢀꢀ
�ꢛꢀ
�ꢙꢀ
�ꢀꢀ
ꢥꢀ
ꢙꢙꢀꢚꢐ
ꢛꢜꢀꢚꢐ
ꢡꢣꢀ
ꢛꢜꢀꢚꢐ
�ꢀꢀꢚꢐ
ꢡꢦꢀ
ꢣꢀ
ꢙꢙꢀꢚꢐ
ꢙꢙꢀꢚꢐ
�ꢀ
ꢛꢀ
ꢡ�ꢙꢀ
ꢡ�ꢤꢀ
ꢡ�ꢥꢀ
ꢡꢙ�ꢀ
�ꢀꢀꢚꢐ
ꢙꢀ
ꢛꢜꢀꢚꢐ
�ꢀꢀꢚꢐ
ꢀ
ꢡꢙꢀ
ꢡꢛꢀ
�
�
�ꢀ �ꢀꢀ �ꢏ �ꢀꢏ �ꢀꢀꢏ �ꢠ �ꢀꢠ
ꢐꢈꢎꢑꢊꢎꢌꢒꢓꢔꢃꢐꢃꢕꢖꢗꢘ
�
�ꢀ �ꢀꢀ �ꢏ �ꢀꢏ �ꢀꢀꢏ �ꢠ �ꢀꢠ
ꢐꢈꢎꢑꢊꢎꢌꢒꢓꢔꢃꢐꢃꢕꢖꢗꢘ
�
�ꢀ
�ꢀꢀ
�ꢀꢀꢀ
ꢐꢈꢎꢑꢊꢎꢌꢒꢓꢃꢕꢲꢖꢗꢘ
ꢉꢍꢌꢏꢇꢁꢀꢊꢌꢇꢐꢉꢑꢇꢆꢃꢂꢋꢑ
ꢃꢒꢊꢋꢒꢊꢇꢐꢃꢍꢊꢀꢎꢌꢇꢉꢏꢅꢄꢎ
ꢤꢀ
ꢛꢀ
ꢢꢀ
ꢙꢀ
ꢦ
ꢥ
ꢜ
ꢣ
ꢤ
ꢛ
ꢢ
ꢙ
�
ꢀ
�ꢀꢪꢃꢧꢋꢞꢄ
�ꢀ
ꢀ
�ꢀꢀ
ꢙꢀꢀ
ꢢꢀꢀ
ꢛꢀꢀ
ꢤꢀꢀ
ꢀ
ꢙ
ꢛ
ꢥ
ꢣ
�ꢀ
ꢎꢰꢇꢁꢃꢒꢋꢠꢝꢎꢌꢆꢞꢇꢅꢋꢌꢃꢒꢞꢝꢞꢒꢅꢇꢋꢈꢃꢕꢚꢐꢘ
ꢋꢊꢇꢝꢊꢇꢃꢒꢊꢈꢈꢎꢌꢇꢔꢃꢅꢋꢃꢕꢞꢘ
APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL prodlit@apexmicrotech.com
3
ABSOLUTE MAXIMUM RATINGS
SPECIFICATIONS
MP39 • MP39A
BYPASSING
GENERAL
Properbypassingofthepowersupplypinsiscrucialforproper
operation. Bypass the ±Vs pins with a aluminum electrolytic
capacitor with a value of at least 10µF per amp of expected
output current. In addition a .47µF to 1µF ceramic capacitor
should be placed in parallel with each aluminum electrolytic
capacitor. Both of these capacitors have to be placed as close
tothepowersupplypinsasphysicallypossible.Ifnotconnected
to the Vs pins (See BOOST OPERATION) the VB pins should
also be bypassed with a .47µF to 1µF ceramic capacitor.
Please read Application Note 1 "General Operating Con-
siderations" which covers stability, supplies, heat sinking,
mounting, current limit, SOA interpretation, and specification
interpretation. Visit www.apexmicrotech.com for design tools
that help automate tasks such as calculations for stability,
internal power dissipation, current limit; heat sink selection;
Apex’s complete Application Notes library; Technical Seminar
Workbook; and Evaluation Kits.
CURRENT LIMIT
USING THE IQ PIN FUNCTION
Thetwocurrentlimitsenselinesaretobeconnecteddirectly
across the current limit sense resistor. For the current limit
to work correctly pin 24 must be connected to the amplifier
output side and pin 23 connected to the load side of the current
limit resistor, RCL, as shown in Figure 1. This connection will
bypass any parasitic resistances, Rp, formed by sockets and
solder joints as well as internal amplifier losses. The current
limiting resistor may not be placed anywhere in the output
Pin 25 (Iq) can be tied to pin 6 (Cc1) to eliminate the class
AB biasing current from the output stage. Typically this would
remove 1-4 mA of quiescent current. The resulting decrease
in quiescent power dissipation may be important in some
applications. Note that implementing this option will raise the
output impedance of the amplifier and increase crossover
distortion as well.
circuit except where shown in Figure 1.
COMPENSATION
The value of the current limit resistor can be calculated as
The external compensation components CC and RC are con-
nected to pins 4 and 6. Unity gain stability can be achieved at
any compensation capacitance greater than 470 pF with at
least 60 degrees of phase margin. At higher gains more phase
shift can be tolerated in most designs and the compensation
capacitance can accordingly be reduced, resulting in higher
bandwidth and slew rate.
follows:
.7
I LIMIT
RCL
=
�
ꢀ
APPLICATION REFERENCES
For additional technical information please refer to the fol-
lowing application notes.
ꢄꢂ
�
ꢁ
ꢂꢃ
ꢄꢅ
ꢄꢆ
�
�
ꢇꢈ
ꢊ
ꢁꢋꢊꢌꢍ
AN 1
AN 11
AN 38
General Operating Considerations
Thermal Techniques
Loop Stability with Reactive Loads
ꢉꢊꢂꢅ
ꢎꢏꢐꢎꢑ
�
ꢈ
ꢀꢁꢒꢌ�ꢓꢔꢎꢕꢔꢇꢌ��ꢓꢋꢍꢔꢈꢁꢉꢁꢍ
BOOST OPERATION
With the V feature the small signal stages of the amplifier
areoperatedBathighersupplyvoltagesthantheamplifier'shigh
current output stage. +VS (pins 12-14) and –V (pins 18-20)
are connected to the high current output stage.SAn additional
10V on the VB pins is sufficient to allow the small signal stages
to drive the output transistors into saturation and improve the
outputvoltageswingforextraefficientoperationwhenrequired.
When close swing to the supply rails is not required the +V
and +V pins must be strapped together as well as the –VBB
and –VSSpins. The boost voltage pins must not be at a voltage
lower than the VS pins.
This data sheet has been carefully checked and is believed to be reliable, however, no responsibility is assumed for possible inaccuracies or omissions. All specifications are subject to change without notice.
4
MP39U REV G JANUARY 2005 © 2005 Apex Microtechnology Corp
.
相关型号：
©2020 ICPDF网 联系我们和版权申明