AWT6221R_10 [ANADIGICS]
HELP3 Dual-band Cellular/PCS UMTS 3.4 V HSPA Linear Power Amplifier Module; HELP3双波段蜂窝/ PCS UMTS 3.4 V HSPA线性功率放大器模块型号: | AWT6221R_10 |
厂家: | ANADIGICS, INC |
描述: | HELP3 Dual-band Cellular/PCS UMTS 3.4 V HSPA Linear Power Amplifier Module |
文件: | 总8页 (文件大小:583K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
AWT6221R
HELP3TM Dual-band Cellular/PCS UMTS
3.4 V HSPA Linear Power Amplifier Module
DATA SHEET - Rev 2.4
FEATURES
•
InGaP HBT Technology
•
High Efficiency:
19 % @ +16 dBm POUT
40 % @ maximum POUT
•
•
•
•
•
•
•
•
Low Quiescent Current: 8 mA
Internal Voltage Regulation
Common VMODE Control Line
Simplified VCC Bus PCB routing
Reduced External Component Count
Low Profile Surface Mount Package: 1 mm
HSDPA Compliant
A
W
T6221R
RoHS Compliant Package, 250 oC MSL-3
APPLICATIONS
M28 Package
14 Pin 3 mm x 5 mm x 1 mm
Surface Mount Module
•
WCDMA/HSPA Dual-Band Cell/PCS Wireless
Handsets and Data Devices
PRODUCT DESCRIPTION
TheAWT6221R addresses the demand for increased
integration in dual-band handsets for NorthAmerican
UMTS network deployments. The small footprint 3
mm x 5 mm x 1 mm surface mount RoHS compliant
package contains independent RF PApaths to ensure
optimal performance in both frequency bands, while
achieving a 25% PCB space savings compared with
solutions requiring two single-band PAs. The package
pinout was chosen to enable handset manufacturers
to easily route VCC to both power amplifiers and
simplify control with a common VMODE pin. The
device is manufactured on an advanced InGaP HBT
MMIC technology offering state-of-the-art reliability,
temperature stability, and ruggedness. TheAWT6221R
incorporates ANADIGICS’ HELP3™ technology to
provide low power consumption without the need for
an external voltage regulator. Two operating modes
provide optimum efficiency at high and medium/low
power output levels, thereby dramatically increasing
handset talk-time and standby-time. Its built-in voltage
regulator eliminates the need for external voltage
regulation and load switches. The 3 mm x 5 mm x 1
mm surface mount package incorporates matching
networks optimized for output power, efficiency and
linearity in a 50 Ω system.
Figure 1: Block Diagram
08/2010
AWT6221R
Figure 2: Pinout
Table 1: Pin Description
PIN
1
NAME
DESCRIPTION
V
EN_CELL
Enable Voltage for Cell Band
RF Input for Cell Band
Mode Control Voltage 1
Battery Voltage
2
RFIN_CELL
3
V
MODE1
4
V
BATT
5
V
MODE2 (N/C) No Connection
RF Input for PCS Band
6
RFIN_PCS
7
V
EN_PCS
Enable Voltage for PCS Band
RF Output for PCS Band
Ground
8
RFOUT_PCS
GND
9
10
11
12
13
14
GND
Ground
V
CC
A
Supply Voltage A
Supply Voltage
V
CC
RFOUT_CELL
GND
RF Output for Cell Band
Ground
Data Sheet - Rev 2.4
2
08/2010
AWT6221R
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings
PARAMETER
MIN
0
MAX
+5
UNIT
V
Supply Voltage (VBATT, VCC, VCCA)
Mode Control Voltage (VMODE1
)
0
+3.5
+3.5
+10
+150
V
Enable Voltage (VEN_CELL, VEN_PCS
)
0
V
RF Input Power (PIN
)
-
dBm
°C
Storage Temperature (TSTG
)
-40
Stresses in excess of the absolute ratings may cause permanent damage.
Functional operation is not implied under these conditions. Exposure
to absolute ratings for extended periods of time may adversely affect
reliability.
Table 3: Operating Ranges
PARAMETER
MIN
TYP
MAX
UNIT
MHz
V
COMMENTS
Cellular
824
1850
849
1910
Operating Frequency (f)
-
PCS
Supply Voltage (VCC and VBATT
)
+3.2
+3.4
+4.2
+2.2
0
+2.4
-
+3.1
+0.5
PA "on"
PA "shut down"
Enable Voltage (VEN
)
V
+2.2
0
+2.4
-
+3.1
+0.5
Low Bias Mode
High Bias Mode
Mode Control Voltage (VMODE1
)
V
Cellular RF Output Power (POUT
)
R99 WCDMA, HPM
HSPA (MPR=0), HPM
R99 WCDMA, LPM
HSPA (MPR=0), LPM
28.5 (1)
27.5 (1)
15.5 (1)
14.5 (1)
29
28
16
15
29
28
16
15
3GPP TS 34.121-1, Rel
7 Table C.11.1.3
dBm
PCS RF Output Power (POUT
)
R99 WCDMA, HPM
HSPA (MPR=0), HPM
R99 WCDMA, LPM
29 (1)
28 (1)
29.5
28.5
16
29.5
28.5
16
3GPP TS 34.121-1, Rel
7 Table C.11.1.3
dBm
15.5 (1)
14.5 (1)
HSPA (MPR=0), LPM
15
15
Case Temperature (T
C
)
-20
-
+90
°C
The device may be operated safely over these conditions; however, parametric performance is guaranteed only
over the conditions defined in the electrical specifications.
Notes:
(1) For operations at VCC = +3.2 V, POUT is derated by 0.5 dB (all operating modes).
Data Sheet - Rev 2.4
3
08/2010
AWT6221R
Table 4: Electrical Specifications - Cellular Band
(T
C
= +25 °C, VBATT = VCC = +3.4 V, VENABLE = +2.4 V, 50 Ω system)
COMMENTS
PARAMETER
MIN
TYP
MAX
UNIT
P
OUT
V
MODE1
24.5
13.5
27
15.5
29.0
18.0
+29 dBm
+16 dBm
0 V
2.4 V
Gain
dB
dBc
dBc
%
-
-
-41
-44
-37.5
-38
+29 dBm
+16 dBm
0 V
2.4 V
ACLR1 at 5 MHz offset (1)
ACLR2 at 10 MHz offset
Power-Added Efficiency (1)
-
-
-60
-57
-48
-48
+29 dBm
+16 dBm
0 V
2.4 V
38
18
42
22
-
-
+29 dBm
+16 dBm
0 V
2.4 V
Quiescent Current (Icq)
Mode Control Current
Enable Current
5
-
8
13
0.8
0.8
5
mA
mA
mA
mA
VMODE1 = +2.4 V
0.35
0.5
2.5
through VMODE1 pin, VMODE = +2.4 V
through VENABLE pin
-
BATT Current
-
through VBATT pin, VMODE1 = +2.4 V
V
V
BATT = +4.2 V, VCC = +4.2 V,
ENABLE = 0 V, VMODE1 = 0 V
Leakage Current
-
<1
5
µA
-
-
-135
-141
-133
-138
P
P
OUT = +29 dBm, VMODE1 = 0 V, V
OUT = +16 dBm, VMODE1 = +2.4 V
Noise in Receive Band (2)
dBm/Hz
Harmonics
2fo
3fo, 4fo
-
-
-44
-50
-35
-35
P
OUT < +29 dBm
dBc
VSWR
dBc
Input Impedance
-
-
-
-
2:1
Spurious Output Level
(all spurious outputs)
-70
See Note 3
Load mismatch stress with no
permanent degradation or failure
8:1
-
-
VSWR Applies over full operating range
Notes:
(1) ACLR and Efficiency measured at 836.5 MHz.
(2) 869 MHz to 894 MHz.
(3) POUT < +29 dBm, In-band load VSWR < 5:1, Out-of-band load VSWR < 10:1. Applies over all operating conditions.
Data Sheet - Rev 2.4
4
08/2010
AWT6221R
Table 5: Electrical Specifications - PCS Band
(T
C
= +25 °C, VBATT = VCC = +3.4 V, VENABLE = +2.4 V, 50 Ω system)
COMMENTS
PARAMETER
MIN
TYP
MAX
UNIT
P
OUT
V
MODE1
24.5
12
26.5
14.0
29.0
17.0
+29.5 dBm
+16 dBm
0 V
2.4 V
Gain
dB
dBc
dBc
%
-
-
-41
-42
-37.5
-38
+29.5 dBm
+16 dBm
0 V
2.4 V
ACLR1 at 5 MHz offset (1)
ACLR2 at 10 MHz offset
Power-Added Efficiency (1)
-
-
-55
-54
-48
-48
+29.5 dBm
+16 dBm
0 V
2.4 V
35
15
38.5
17.5
-
-
+29.5 dBm
+16 dBm
0 V
2.4 V
Quiescent Current (Icq)
Low Bias Mode
5
-
8
13
0.8
0.8
5
mA
mA
mA
mA
VMODE1 = +2.4 V
Mode Control Current
Enable Current
0.35
0.35
2.5
through VMODE pins, VMODE = +2.4 V
through VENABLE pin
-
BATT Current
-
through VBATT pin, VMODE1 = 2.4 V
V
V
BATT = +4.2 V, VCC = +4.2 V,
ENABLE = 0 V, VMODE1 = 0 V
Leakage Current
-
<1
5
µA
-
-
-137
140
-135
-138
P
P
OUT = +29.5 dBm, VMODE1 = 0 V
OUT = +16 dBm, VMODE1 = 2.4 V
Noise in Receive Band (2)
dBm/Hz
Harmonics
2fo
3fo, 4fo
-
-
-42
-46
-35
-35
dBc
Input Impedance
-
-
2:1
VSWR
P
OUT < +29.5 dBm
In-band load VSWR < 5:1
Out-of-band load VSWR < 10:1
Applies over all operating
conditions
Spurious Output Level
(all spurious outputs)
-
-
-70
dBc
Load mismatch stress with no
permanent degradation or failure
8:1
-
-
VSWR Applies over full operating range
Notes:
(1) ACLR and Efficiency measured at 1880 MHz.
(2) 1930 MHz to 1990 MHz.
Data Sheet - Rev 2.4
5
08/2010
AWT6221R
APPLICATION INFORMATION
The Bias Control table lists the recommended modes
of operation for various applications. VMODE2 is not
necessary for this PA.
To ensure proper performance, refer to all related
Application Notes on the ANADIGICS web site:
http://www.anadigics.com
Two operating modes are available to optimize
current consumption. High Bias/High Power operating
mode is for POUT levels > 16 dBm. At around 16 dBm
output power, the PA should be “Mode Switched” to
Medium/Low power mode for lowest quiescent current
consumption.
Shutdown Mode
The power amplifier may be placed in a shutdown
mode by applying logic low levels (see Operating
Ranges table) to the VENABLE and VMODE1 voltages.
Bias Modes
The power amplifier may be placed in either a Low Bias
mode or a High Bias mode by applying the appropriate
logic level (see Operating Ranges table) to VMODE1.
Table 6: Bias Control
P
OUT
BIAS
MODE
APPLICATION
V
ENABLE
V
MODE1
V
CC
V
BATT
LEVELS
< +16 dBm
> +16 dBm
UMTS - low power
Low
+2.4 V +2.4 V
+2.4 V 0 V
3.2 - 4.2 V
3.2 - 4.2 V
> 3.2 V
> 3.2 V
UMTS - high power
High
Optional lower VCC in
low power mode
< +7 dBm
Low
+2.4 V +2.4 V
0 V 0 V
1.5 V
> 3.2 V
> 3.2 V
Shutdown
-
Shutdown
3.2 - 4.2 V
Figure 3: Application Circuit
Data Sheet - Rev 2.4
6
08/2010
AWT6221R
PACKAGE OUTLINE
Figure 4: Package Outline - 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module
LLLL
087
6221R
LLLLNN
087CC
YYWW
7. YEAR AND WORK WEEK YY = Year, WW = Work Week
8
Figure 5: Branding Specification
Data Sheet - Rev 2.4
7
08/2010
AWT6221R
ORDERING INFORMATION
ORDER
NUMBER
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
COMPONENT PACKAGING
RoHS Compliant 14 Pin
3 mm x 5 mm x 1 mm
Surface Mount Module
AWT6221RM28Q7 -20 °C to +85 °C
AWT6221RM28P9 -20 °C to +85 °C
Tape and Reel, 2500 pieces per Reel
RoHS Compliant 14 Pin
3 mm x 5 mm x 1 mm
Surface Mount Module
Partial Tape and Reel
ANADIGICS, Inc.
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
E-mail: Mktg@anadigics.com
IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice.
The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to
change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed
to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers
to verify that the information they are using is current before placing orders.
WARNING
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of anANADIGICS product
in any such application without written consent is prohibited.
Data Sheet - Rev 2.4
8
08/2010
相关型号:
AWT6222
HELP3TM Tri-band US Cellular/Japan Cellular/IMT UMTS/WCDMA Linear Power Amplifier Module
ANADIGICS
AWT6222RM28P9
HELP3TM Tri-band US Cellular/Japan Cellular/IMT UMTS/WCDMA Linear Power Amplifier Module
ANADIGICS
AWT6222RM28Q7
HELP3TM Tri-band US Cellular/Japan Cellular/IMT UMTS/WCDMA Linear Power Amplifier Module
ANADIGICS
AWT6223RM26P8
WCDMA/GSM/GPRS/Polar EDGE Power Amplifier Module with Integrated Power Control
ANADIGICS
AWT6223RM26P9
WCDMA/GSM/GPRS/Polar EDGE Power Amplifier Module with Integrated Power Control
ANADIGICS
©2020 ICPDF网 联系我们和版权申明