TSL2568 [AMSCO]
LIGHT-TO-DIGITAL CONVERTER; 光 - 数字转换器![TSL2568](http://pdffile.icpdf.com/pdf1/p00188/img/icpdf/TSL256_1063622_icpdf.jpg)
型号: | TSL2568 |
厂家: | ![]() |
描述: | LIGHT-TO-DIGITAL CONVERTER |
文件: | 总37页 (文件大小:791K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
TAOS Inc.
is now
ams AG
The technical content of this TAOS datasheet is still valid.
Contact information:
Headquarters:
ams AG
Tobelbaderstrasse 30
8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0
e-Mail: ams_sales@ams.com
Please visit our website at www.ams.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
r
r
TAOS091D − DECEMBER 2008
PACKAGE CS
6-LEAD CHIPSCALE
(TOP VIEW)
D Approximates Human Eye Response
D Approximately 4ꢀ More Sensitive Than
TSL2560/61 Device
D Programmable Interrupt Function with
User-Defined Upper and Lower Threshold
Settings
6 SDA
5 INT
4 SCL
VDD
1
ADDR SEL 2
GND 3
D 16-Bit Digital Output with SMBus (TSL2568)
2
at 100 kHz or I C (TSL2569) Fast-Mode at
400 kHz
Package Drawings are Not to Scale
D Programmable Analog Gain and Integration
Time Supporting 1,000,000-to-1 Dynamic
Range
PACKAGE T
6-LEAD TMB
(TOP VIEW)
D Available in Ultra-Small 1.25 mm
1ꢀ.75 mm
Chipscale Package
VDD
1
6 SDA
5 INT
4 SCL
D Automatically Rejects 50/60-Hz Lighting
Ripple
ADDR SEL 2
GND 3
D Low Active Power (0.75 mW Typical) with
Power Down Mode
D RoHS Compliant
Description
The TSL2568 and TSL2569 are high-ensitivity light-to-digial converters that transform light intensity to a digital
2
signal output capable of direct I C (TSL2569) or SMBus (TSL2568) interface. Each device combines one
broadband photodiode (visile lus infrared) and ne infrared-responding photodiode on a single CMOS
integrated circuit capable of prding a near-phic response over an effective 20-bit dynamic range (16-bit
resolution). Two integrating ADCs convert thtodiode currents to a digital output that represents the
irradiance measured on each channel. Ths digital output can be input to a microprocessor where illuminance
(ambient light level) in lux is derived using an mpirical formula to approximate the human eye response. The
TSL2568 device permits an SMB-Art style interrupt, and the TSL2569 device supports a traditional level style
interrupt that remains asserted until thfirmware clears it.
While useful for general purpose t sensing applications, the TSL2568/69 devices are designed particularly
for display panels (LCD, OED, etc.) with the purpose of extending battery life and providing optimum viewing
in diverse lighting condition. Dsplay panel backlighting, which can account for up to 30 to 40 percent of total
platform power, can be auomatically managed. Both devices are also ideal for controlling keyboard illumination
based upon ambient lighting conditions. Illuminance information can further be used to manage exposure
control in digital cameras. The TSL2568/69 devices are ideal in notebook/tablet PCs, LCD monitors, flat-panel
televisions, ll phones, and digital cameras. In addition, other applications include street light control, security
lighting, sunligt harvesting, machine vision, and automotive instrumentation clusters.
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
Texas Advarnced Optoelectronic Solutions Inc.
1001 Klein Road S Suite 300 S Plano, TX 75074 S (972) 673-0759
www.taosinc.com
1
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
Functional Block Diagram
Channel 0
Visible and IR
Integrating
A/D Converter
Channel 1
IR Only
V
= 2.7 V to 3.5 V
DD
Command
Register
ADC
Register
Address Select
Interrupt
ADDR SEL
INT
SCL
SA
Two-Wire Serial Interface
Detailed Description
The TSL2568 and TSL2569 are second-generation ambient light sensor devices. Each conains two integrating
analog-to-digital converters (ADC) that integrate currents from two photodiodes. Integation of both channels
occurs simultaneously. Upon completion of the conversiocycle, the conversion result is transferred to the
Channel 0 and Channel 1 data registers, respectively. The transfers are double-bufered to ensure that the
integrity of the data is maintained. After the transfer, thice automaticaly begins the next integration cycle.
2
Communication to the device is accomplished throuh a standard, two-wire SMBus or I C serial bus.
Consequently, the TSL256x device can be easily connected to a micconroller or embedded controller. No
external circuitry is required for signal conditiningthereby saving PCB real estate as well. Since the output
of the TSL256x device is digital, the output ieffectively immune noise when compared to an analog signal.
The TSL256x devices also support an inerrupt feature that implifies and improves system efficiency by
eliminating the need to poll a sensor for a light intensity valueThe primary purpose of the interrupt function is
to detect a meaningful change in ghntensity. The concepof a meaningful change can be defined by the user
both in terms of light intensity and te, or persistenthat change in intensity. The TSL256x devices have
the ability to define a threshold above and below the nt light level. An interrupt is generated when the value
of a conversion exceeds either of these limits.
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
2
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
Terminal Functions
TERMINAL
TYPE
DESCRIPTION
T PKG
NO.
NAME
ADDR SEL
GND
2
3
5
4
6
1
I
SMBus device select — three-state
Power supply ground. All voltages are referenced to GND.
Level or SMB Alert interrupt — open drain.
INT
O
I
SCL
SMBus serial clock input terminal — clock signal for SMBus serial data.
SMBus serial data I/O terminal — serial data I/O for SMBus.
Supply voltage.
SDA
I/O
V
DD
Available Options
DEVICE
TSL2568
TSL2568
TSL2569
TSL2569
INTERFACE
SMBus
PACKAGE − LEADS PACKAGE DESIGNATOR ORDERNG NUMBER
Chipscale
TMB-6
CS
T
TL256CS
TSL68T
TS2569CS
SL2569T
SMBus
2
I C
Chipscale
TMB-6
CS
T
2
I C
Absolute Maximum Ratings over operating freair temperature ange (unless otherwise noted)†
Supply voltage, V (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 V
DD
Digital output voltage range, V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 3.8 V
O
Digital output current, I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −1 mA to 20 mA
O
Storage temperature range, T
ESD tolerance, human body modl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C
stg
†
Stresses beyond those listed under “absutaximum ratings” may cae permanent damage to the device. These are stress ratings only, and
functional operation of the device at these ny other conditiyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for ed periods may affect device reliability.
NOTE 1: All voltages are with respect to GND.
Recommended Operating Conditions
MIN NOM
MAX
3.6
UNIT
V
Supply voltage, V
2.7
−30
−0.5
2.1
3
DD
Operating free-air temperature, T
70
°C
A
SCL, SDA input low voltage, V
0.8
3.6
V
V
SCL, SDA input high voltageV
IH
Electrical Characteristics over recommended operating free-air temperature range (unless
otherwise note)
PARAMETER
TEST CONDITIONS
MIN
TYP
0.24
3.2
MAX
0.6
15
UNIT
mA
μA
Active
I
Supply current
DD
Power down
V
I
INT, SDA output low voltage
Leakage current
3 mA sink current
0
0.4
5
V
OL
−5
μA
LEAK
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
3
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
Operating Characteristics, High Gain (16ꢀ), VDD = 3 V, TA = 25ꢁ C, (unless otherwise noted) (see
Notes 2, 3, 4, 5)
TSL2568T, TSL2569T TSL2568CS, TSL2569CS
PARAMETER
TEST CONDITIONS
CHANNEL
UNIT
MIN
690
0
TYP
MAX
780
MIN
690
0
TYP
MAX
780
f
Oscillator frequency
735
735
kHz
osc
Ch0
Ch1
Ch0
Ch1
Ch0
Ch1
Ch0
Ch1
Ch0
Ch1
Ch0
Ch1
Ch0
Ch1
Ch0
Ch1
8
8
Dark ADC count value
E = 0, T = 402 ms
counts
e
int
0
8
0
8
65535
65535
37177
37177
5047
5047
5000
65535
65535
37177
37177
5047
5047
T
T
T
> 178 ms
int
int
int
Full scale ADC count
value (Note 6)
= 101 ms
= 13.7 ms
counts
3000
2800
4000
1000
4000
3520
λ = 640 nm, T = 101 ms
p
int
2
E = 33 μW/cm
e
counts
counts
5200
λ = 940 nm, T = 101 ms
p
int
2
E = 106 μW/cm
e
ADC count value
3000
2800
4000
840
5000
5200
λ = 640 nm, T = 101 ms
p
int
2
E = 34.5 μW/cm
e
4000
3440
λ = 940 nm, T = 101 ms
p
int
2
E = 110.9 μW/cm
e
λ = 640 nm, T = 101 ms
0.18
0.73
0.25
0.88
1
3.3
37.7
33.2
185
35
032
1.03
0.14
0.70
0.21
0.86
116
24
0.28
1.01
ADC count value ratio:
Ch1/Ch0
p
int
λ = 940 nm, T = 101 ms
p
int
C0
Ch1
Ch0
Ch1
Ch
Ch
Ch0
Ch1
λ = 640 nm, T = 101 ms
p
int
counts/
(μW/
R
R
Irradiance responsivity
Illuminance responsivity
e
36
2
cm )
λ = 940 nm, T = 11 ms
p
31
180
33.3
537
307
Fluorescent ligource:
= 402 ms
T
int
counts/
lux
v
599
330
Incandescent light source:
= 402 ms
T
int
Fluorescent light sourc:
= 402 ms
0.19
0.55
0.19
0.57
T
int
ADC count value ratio:
Ch1/Ch0
Incandescent light rce:
= 402 ms
T
int
Ch0
Ch1
Ch0
Ch1
11.6
2.2
11.1
2.1
Fluorecent ghsource:
= 402 ms
T
int
Illuminance responsivity,
low gain mode (Note 7)
counts/
lux
R
v
37.5
20.7
33.8
19.3
Icandescent light source:
402 ms
T
int
Fuorescent light source:
= 402 ms
0.65
0.60
1
1
1.35
1.40
0.65
0.60
1
1
1.35
1.40
(Sensor Lux) /
(actual Lux), hh gai
mode (Note 8)
T
int
Incandescent light source:
= 402 ms
T
int
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
4
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
NOTES: 2. Optical measurements are made using small-angle incident radiation from light-emitting diode optical sources. Visible 640 nm LEDs
and infrared 940 nm LEDs are used for final product testing for compatibility with high-volume production.
3. The 640 nm irradiance E is supplied by an AlInGaP light-emitting diode with the following characteristics: peak wavelength
e
λp = 640 nm and spectral halfwidth Δλ½ = 17 nm.
4. The 940 nm irradiance E is supplied by a GaAs light-emitting diode with the following characteristics: peak wavelength
e
λp = 940 nm and spectral halfwidth Δλ½ = 40 nm.
5. Integration time T , is dependent on internal oscillator frequency (f ) and on the integration field value in the timing register as
int
osc
described in the Register Set section. For nominal f
= 735 kHz, nominal T = (number of clock cycles)/f
.
osc
int
osc
Field value 00: T = (11 × 918)/f
= 13.7 ms
= 101 ms
= 402 ms
osc
int
osc
Field value 01: T = (81 × 918)/f
int
osc
Field value 10: T = (322 × 918)/f
int
Scaling between integration times vary proportionally as follows: 11/322 = 0.034 (field value 00), 81/322 = 0.252 (field value 01),
and 322/322 = 1 (field value 10).
6. Full scale ADC count value is limited by the fact that there is a maximum of one count per two oscillator frequency periods analso
by a 2-count offset.
Full scale ADC count value = ((number of clock cycles)/2 − 2)
Field value 00: Full scale ADC count value = ((11 × 918)/2 − 2) = 5047
Field value 01: Full scale ADC count value = ((81 × 918)/2 − 2) = 37177
Field value 10: Full scale ADC count value = 65535, which is limited by 16 bit register. This full scale ADC count value is reached
for 131074 clock cycles, which occurs for T = 178 ms for nominal f
= 735 kHz.
int
osc
7. Low gain mode has 16ꢀ lower gain than high gain mode: (1/16 = 0.0625).
8. The sensor Lux is calculated using the empirical formula shown on p. 22 of this data sheet based n msured Ch0 and Ch1 ADC
count values for the light source specified. Actual Lux is obtaineith a commercial luxmeter. e rae of the (sensor Lux) / (actual
Lux) ratio is estimated based on the variation of the 640 nm and 9nm optical parameters. evices are not 100% tested with
fluorescent or incandescent light sources.
AC Electrical Characteristics, VDD = 3 V, TA = 2ꢁ C (unless otherwise noted)
†
PARAMETER
Conversion time
TEST CONDIIONS
MIN
12
0
TYP
MAX
400
400
100
UNIT
ms
t
100
(CONV)
2
Clock frequency (I C only)
kHz
kHz
μs
f
t
t
(SCL)
Clock frequency (SMBus only)
10
1.3
Bus free time between start anstop condition
(BUF)
Hold time after (repeated) staondition. After
this period, the first clock is generated.
0.6
μs
(HDSTA)
t
t
t
t
t
t
t
t
t
Repeated start condition setup time
Stop condition setup time
Data hold time
0.6
0.6
0
μs
μs
μs
ns
μs
μs
ms
ns
ns
pF
(SUSTA)
(SUSTO)
(HDDAT)
(SUDAT)
(LOW)
(HIGH)
(TIMEOUT)
F
0.9
Data setup time
100
1.3
0.6
25
SCL clock low period
SCL clock high period
Detect clock/data low tieout (SMBus only)
Clock/data fall me
35
300
300
10
Clockdatrie time
R
C
Input pin apacitance
i
†
Specified by deign and characterization; not production tested.
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
5
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
PARAMETER MEASUREMENT INFORMATION
t
t
(R)
t
(F)
(LOW)
V
IH
SCL
SDA
V
IL
t
t
t
(HDSTA)
(HIGH)
(SUSTA)
t
t
t
(SUSTO)
t
(BUF)
(HDDAT)
(SUDAT)
V
V
IH
IL
P
S
S
P
Stop
Condition
Start
Condition
Start
Stop
t
(LOWSEXT)
SCL
SCL
ACK
ACK
t
t
t
(LOWMEXT)
(LOWMEXT)
(LOWMEXT)
SCL
SDA
Figure 1. TimiDiagrams
1
9
1
9
SCL
SDA
A6 A5
A4
A3
A2 A0 R/W
DD6
D5 D4 D3 D2
D1 D0
Start by
Master
AC
TSL2
ACK by Stop by
TSL256x Master
Frame 1 SMBus Slave Address Byte
Frame 2 Command Byte
Figure 2. Example Timing Diagram for SMBus Send Byte Format
1
9
1
9
SCL
SDA
A6 A
A4
A3
A2 A1 A0 R/W
D7 D6
D5 D4 D3 D2
D1 D0
Start by
Master
ACK by
TSL256x
NACK by Stop by
Master Master
Frame 1 SMBus Slave Address Byte
Frame 2 Data Byte From TSL256x
Figure 3. Example Timing Diagram for SMBus Receive Byte Format
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
6
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
TYPICAL CHARACTERISTICS
SPECTRAL RESPONSIVITY
1
0.8
0.6
Channel 0
Photodiode
0.4
0.2
0
Chnnel 1
Potodiod
300 400 500 600 800 900 1001100
λ − Wavength − nm
Figure 4
NORMALIZED RESPONSIVIT
NORMALIZED RESPONSIVITY
vs.
vs.
ANGULAR DISPLACEMENT — CS PACKAGE
ANGULAR DISPLACEMENT — TMB PACKAGE
1.0
0.8
1.0
0.8
0.6
0.4
0.6
0.4
0.2
0
0.2
0
90
90
−90
60
−30
0
30
60
−90
−60
−30
0
30
60
ꢀ
−
A
n
g
u
l
a
r
D
i
s
p
l
a
c
e
m
e
n
t
−
°
ꢀ
−
A
n
g
u
l
a
r
D
i
s
p
l
a
c
e
m
e
n
t
−
°
Figure 5
Figure 6
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
7
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
PRINCIPLES OF OPERATION
Analog-to-Digital Converter
The TSL256x contains two integrating analog-to-digital converters (ADC) that integrate the currents from the
channel 0 and channel 1 photodiodes. Integration of both channels occurs simultaneously, and upon completion
of the conversion cycle the conversion result is transferred to the channel 0 and channel 1 data registers,
respectively. The transfers are double buffered to ensure that invalid data is not read during the transfer. After
the transfer, the device automatically begins the next integration cycle.
Digital Interface
Interface and control of the TSL256x is accomplished through a two-wire serial interface to a set of regsts
that provide access to device control functions and output data. The serial interface is compatible with Sysm
2
Management Bus (SMBus) versions 1.1 and 2.0, and I C bus Fast-Mode. The TSL256x offers threslave
addresses that are selectable via an external pin (ADDR SEL). The slave address options are shown in Table 1.
Table 1. Slave Address Selection
ADDR SEL TERMINAL LEVEL
SLAVE ADDESS
010101
SMB ALERT ADRES
0001100
GND
Float
VDD
0111001
00100
1
0001100
2
NOTE: The Slave and SMB Alert Addresses are 7 bits. Please note the SMBs and I C protocols opages 9 through 12. A read/write bit should
be appended to the slave address by the master device to properly communicate witthe TSL256X device.
SMBus and I2C Protocols
Each Send and Write protocol is, esentially, a series bytes. A byte sent to the TSL256x with the most
significant bit (MSB) equal to 1 will nterpreted as OMMAND byte. The lower four bits of the COMMAND
byte form the register select address (see Table 2), is used to select the destination for the subsequent
byte(s) received. The TSL256x responds to any Receive Byte requests with the contents of the register
specified by the stored register select address
The TSL256X implements the following protocols of the SMB 2.0 specification:
D
D
D
D
D
D
D
Send Byte Protocol
Receive Byte Protocol
Write Byte Protocol
Write Word Protoco
Read Word Protocol
Block Write Prtocol
Block Red Potocol
2
TTSL56X implements the following protocols of the Philips Semiconductor I C specification:
D
D
I Write Protocol
2
I C Read (Combined Format) Protocol
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
8
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
When an SMBus Block Write or Block Read is initiated (see description of COMMAND Register), the byte
following the COMMAND byte is ignored but is a requirement of the SMBus specification. This field contains
the byte count (i.e. the number of bytes to be transferred). The TSL2568 (SMBus) device ignores this field and
extracts this information by counting the actual number of bytes transferred before the Stop condition is
detected.
2
2
When an I C Write or I C Read (Combined Format) is initiated, the byte count is also ignored but follows the
2
SMBus protocol specification. Data bytes continue to be transferred from the TSL2569 (I C) device to Master
until a NACK is sent by the Master.
The data formats supported by the TSL2568 and TSL2569 devices are:
2
D
D
Master transmitter transmits to slave receiver (SMBus and I C):
−
The transfer direction in this case is not changed.
Master reads slave immediately after the first byte (SMBus only):
−
At the moment of the first acknowledgment (provided by the slave receiver) he master transmitter
becomes a master receiver and the slave receiver becomes a slave transmiter.
2
D
Combined format (SMBus and I C):
−
During a change of direction within a transfer, te maer repeats both a STRT condition and the slave
address but with the R/W bit reversed. In thicase, the master receiver terminates the transfer by
generating a NACK on the last byte of the transfer and a STOP condition.
For a complete description of SMBus proocols, please reviw the SMBus Specification at
2
2
http://www.smbus.org/specs. For a complete description of I C protocls, please review the I C Specification
at http://www.semiconductors.philips.com.
1
7
1
1
A
8
1
1
S
Sve Address
Wr
Data Byte
A
X
P
A
Acknowledge (this it position may be 0 for an ACK or 1 for a NACK)
P
Stop Condition
Rd
S
Read (bit valuof 1)
Start Cond
Sr
Wr
X
Rpeated Start Condition
Write (bit value of 0)
Shown under a field indicates that that field is required to have a value of X
... Continuation of protocol
Master-to-Slave
Slave-to-Master
2
Figure 7. SMBus and I C Packet Protocol Element Key
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
9
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
1
7
1
1
8
1
1
S
Slave Address
Wr
A
Data Byte
A
P
Figure 8. SMBus Send Byte Protocol
1
7
1
1
8
1
A
1
1
S
Slave Address
Rd
A
Data Byte
P
Figure 9. SMBus Receive Byte Protocol
1
7
1
1
8
1
8
1
1
S
Slave Address
Wr
A
Command Code
A
Data Byte
A
P
Figure 10. SMBus Write Byte Protocol
1
7
1
1
8
1
1
7
1
1
8
1
A
1
1
S
Slave Address
Wr
A
Command Code
A
S
ve Address
Rd
Data Byte Low
P
Figure 11. SMBus Read Byte Prcol
1
7
1
1
8
1
1
8
1
1
S
Slave Address
Wr
A
Comnd Code
A
DatByte Low
A
Data Byte High
A
P
Figure 12. SMBus Write Word Protocol
1
7
1
1
8
1
1
7
1
1
8
1
...
S
Slave Address
Wr
A
Command C
A
S
Slave Address
Rd
A
Data Byte Low
A
8
1
A
1
1
Data Byte High
P
Figure 13. SMBus Read Word Protocol
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
10
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
1
7
1
1
8
1
8
1
8
1
...
S
Slave Address
Wr
A
Command Code
A
Byte Count = N
A
Data Byte 1
A
8
1
8
1
1
...
Data Byte 2
A
Data Byte N
A
P
2
Figure 14. SMBus Block Write or I C Write Protocols
2
NOTE: The I C write protocol does not use the Byte Count packet, and the Master will continue sending Data Bytes until the Master initiates a
Stop condition. See the Command Register on page 13 for additional information regarding the Block Read/Write protocol.
1
7
1
1
8
1
1
7
1
1
8
1
...
S
Slave Address
Wr
A
Command Code
A
Sr Slave Address Rd
A
Byte Count = N
A
8
1
8
1
8
1
...
Data Byte 1
A
Data Byte 2
A
Data Byte N
A
1
P
2
Figure 15. SMBus Block Read or I C Read (Combined Format) Protocols
2
NOTE: The I C read protocol does not use the Byte Count packet, and thMaster will continue receiving ata Bes until the Master initiates
a Stop Condition. See the Command Register on page 13 for aditional iormation regarding the Blk Read/Write protocol.
Register Set
The TSL256x is controlled and monitored by sixten registers (three arreserved) and a command register
accessed through the serial interface. These registers provide for varety of control functions and can be read
to determine results of the ADC conversins. he register set is summarized in Table 2.
Table 2. Register ddress
ADDRESS
−−
RESISTER AME
COMND
REGISTER FUNCTION
Specifies regster address
0h
COROL
Conasic functions
1h
TIMING
Integran time/gain control
Low yte of low interrupt threshold
2h
THRESHLOWLOW
3h
THRESHLOHIGH High byte of low interrupt threshold
THRESHHIGHLW Low byte of high interrupt threshold
THRESHHIGIGH High byte of high interrupt threshold
4h
5h
6h
NTERRPT
−
Interrupt control
7h
Reserved
8h
CRC
Factory test — not a user register
Reserved
9h
−−
A
ID
Part number/ Rev ID
Reserved
Bh
−−
Ch
Dh
Eh
DATA0LOW
DATA0HIGH
DATA1LOW
DATA1HIGH
Low byte of ADC channel 0
High byte of ADC channel 0
Low byte of ADC channel 1
High byte of ADC channel 1
Fh
The mechanics of accessing a specific register depends on the specific SMB protocol used. Refer to the section
on SMBus protocols. In general, the COMMAND register is written first to specify the specific control/status
register for following read/write operations.
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
11
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
Command Register
The command register specifies the address of the target register for subsequent read and write operations.
The Send Byte protocol is used to configure the COMMAND register. The command register contains eight bits
as described in Table 3. The command register defaults to 00h at power on.
Table 3. Command Register
7
CMD
0
6
CLEAR
0
5
WORD
0
4
BLOCK
0
3
2
1
0
0
0
COMMAND
ADDRESS
Reset Value:
0
0
FIELD
CMD
BIT
7
DESCRIPTION
Select command register. Must write as 1.
CLEAR
6
Interrupt clear. Clears any pending interrupt. This bit is a write-one-to-clear bit. It is selclearing.
SMB Write/Read Word Protocol. 1 indicates that this SMB transaction is using either he SB Write Word or
Read Word protocol.
WORD
BLOCK
5
4
Block Write/Read Protocol. 1 indicates that this transaction is using either the lock rite or the Block Read
protocol. See Note below.
Register Address. This field selects the specificontrol status register fofollowing write and read
commands according to Table 2.
ADDRESS
3:0
2
2
NOTE: An I C block transaction will continue until the Master sends a stop ition. See Figure 1nd Figure 15. Unlike the I C protocol, the
SMBus read/write protocol requires a Byte Count. All four ADC Chnel Data Registers (Ch though Fh) can be read simultaneously in
a single SMBus transaction. This is the only 32-bit data block suppoted by the TSL258 SBus protocol. The BLOCK bit must be set
to 1, and a read condition should be initiated with a COMMAND CODE of 9Bh. By usina COMMAND CODE of 9Bh during an SMBus
Block Read Protocol, the TSL2568 device will automaticinsrt the appropriate Cont (Byte Count = 4) as illustrated in Figure 15.
A write condition should not be used in conjunction th the Bh register.
Control Register (0h)
The CONTROL register contains two bits and is primarily used to power the TSL256x device up and down as
shown in Table 4.
Tabe 4. Control Register
7
Resv
0
6
Resv
0
5
Rev
0
4
Resv
0
3
Resv
0
2
Resv
0
1
0
0
0
CONTROL
0h
POWER
Reset Value:
FIELD
BIT
DESCRIPTION
Resv
7:2
Resrved. Write as 0.
Power up/power down. By writing a 03h to this register, the device is powered up. By writing a 00h to this
register, the device is powered down.
POWER
1:0
NOTE: If a value of 03h is written, the value returned during a read cycle will be 03h. This feature can be
used to verify that the device is communicating properly.
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
12
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
Timing Register (1h)
The TIMING register controls both the integration time and the gain of the ADC channels. A common set of
control bits is provided that controls both ADC channels. The TIMING register defaults to 02h at power on.
Table 5. Timing Register
7
Resv
0
6
Resv
0
5
Resv
0
4
GAIN
0
3
Manual
0
2
Resv
0
1
1
0
0
TIMING
1h
INTEG
Reset Value:
FIELD
BIT
DESCRIPTION
Resv
7−5
Reserved. Write as 0.
Switches gain between low gain and high gain modes. Writing a 0 selects low gain (1×); ritina 1 selects
GAIN
4
3
high gain (16×).
Manual timing control. Writing a 1 begins an integration cycle. Writing a 0 stops an tegration cycle.
NOTE: This field only has meaning when INTEG = 11. It is ignored at all other ties.
Manual
Resv
2
Reserved. Write as 0.
INTEG
1:0
Integrate time. This field selects the integation te for each conversion.
Integration time is dependent on the INTEG FIELALUE and the internal clock frequency. Nominal integration
times and respective scaling between integration es scale proportnally as shown in Table 6. See Note 5
and Note 6 on page 5 for detailed information regading how the scale vaues were obtained; see page 22 for
further information on how to calculate lux.
Table 6. Integration me
INTEG FIELD ALU
SCALE
0.034
0.2
OMINAL INTEGRATION TIME
0
0
10
11
13.7 ms
101 ms
402 ms
N/A
−−
The manual timing control feature is used to manually start and stop the integration time period. If a particular
integration time period is required that s not listed in Table 6, then this feature can be used. For example, the
manual timing control can be used synchronize the TSL256x device with an external light source (e.g. LED).
A start command to begin integration can be initiated by writing a 1 to this bit field. Correspondingly, the
integration can be stopped by smply writing a 0 to the same bit field.
Interrupt Threshold Register (2h − 5h)
The interrupt threhold registers store the values to be used as the high and low trigger points for the comparison
function for inerrupt generation. If the value generated by channel 0 crosses below or is equal to the low
threshold specified, an interrupt is asserted on the interrupt pin. If the value generated by channel 0 crosses
above thhigh threshold specified, an interrupt is asserted on the interrupt pin. Registers THRESHLOWLOW
and RESHLOWHIGH provide the low byte and high byte, respectively, of the lower interrupt threshold.
Regtes THRESHHIGHLOW and THRESHHIGHHIGH provide the low and high bytes, respectively, of the
upper interrupt threshold. The high and low bytes from each set of registers are combined to form a 16-bit
theshold value. The interrupt threshold registers default to 00h on power up.
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
13
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
Table 7. Interrupt Threshold Register
REGISTER
ADDRESS
BITS
7:0
DESCRIPTION
THRESHLOWLOW
THRESHLOWHIGH
THRESHHIGHLOW
THRESHHIGHHIGH
2h
3h
4h
5h
ADC channel 0 lower byte of the low threshold
ADC channel 0 upper byte of the low threshold
ADC channel 0 lower byte of the high threshold
ADC channel 0 upper byte of the high threshold
7:0
7:0
7:0
NOTE: Since two 8-bit values are combined for a single 16-bit value for each of the high and low interrupt thresholds, the Send Byte protocol should
not be used to write to these registers. Any values transferred by the Send Byte protocol with the MSB set would be interpreted as the
COMMAND field and stored as an address for subsequent read/write operations and not as the interrupt threshold information as desied.
The Write Word protocol should be used to write byte-paired registers. For example, the THRESHLOWLOW and THRESHLOWHIG
registers (as well as the THRESHHIGHLOW and THRESHHIGHHIGH registers) can be written together to set the 16-bit ADC vale in
a single transaction.
Interrupt Control Register (6h)
The INTERRUPT register controls the extensive interrupt capabilities of the TSL256x. The SL256x permits
both SMB-Alert style interrupts as well as traditional level-style interrupts. The errupt persist bit field
(PERSIST) provides control over when interrupts occur. A alue 0 causes an interrut to occur after every
integration cycle regardless of the threshold settings. A vale of 1 results in an iterrupt after one integration
time period outside the threshold window. A value of (where N is 2 through15) results in an interrupt only if
the value remains outside the threshold window for N cecutive integraticycles. For example, if N is equal
to 10 and the integration time is 402 ms, then the total me is approximately seconds.
When a level Interrupt is selected, an interrupt is generated whenevethe last conversion results in a value
outside of the programmed threshold window. The iterrupt is actiow and remains asserted until cleared by
writing the COMMAND register with the CLER bit set.
In SMBAlert mode, the interrupt is simar to the traditional level style and the interrupt line is asserted low. To
clear the interrupt, the host responds to the SMBAlert by prforming a modified Receive Byte operation, in which
the Alert Response Address (ARA) placed in the slave ddress field, and the TSL256x that generated the
interrupt responds by returning its own address in thn most significant bits of the receive data byte. If more
than one device connected on the bus has pulled the SMBAlert line low, the highest priority (lowest address)
device will win communication rights via stanard rbitration during the slave address transfer. If the device
loses this arbitration, the interrupt will not be cleared. The Alert Response Address is 0Ch.
When INTR = 11, the interrupt is generated immediately following the SMBus write operation. Operation then
behaves in an SMBAlert mode, and thoftware set interrupt may be cleared by an SMBAlert cycle.
NOTE: Interrupts are based on the vale of hannl 0 only.
Table 8. Interrupt Control Register
7
Rsv
0
6
Resv
0
5
4
3
2
1
0
0
0
INTERRUPT
6h
INTR
PERSIST
Reset Value:
0
0
0
0
FEL
Resv
BITS
7:6
DESCRIPTION
Reserved. Write as 0.
INTR Control Select. This field determines mode of interrupt logic according to Table 9, below.
Interrupt persistence. Controls rate of interrupts to the host processor as shown in Table 10, below.
INTR
5:4
PERSIST
3:0
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
14
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
Table 9. Interrupt Control Select
INTR FIELD VALUE
READ VALUE
Interrupt output disabled
00
01
10
11
Level Interrupt
SMBAlert compliant
Test Mode: Sets interrupt and functions as mode 10
NOTE: Field value of 11 may be used to test interrupt connectivity in a system or to assist in debugging interrupt service routine soware
Table 10. Interrupt Persistence Select
PERSIST FIELD VALUE
INTERRUPT PERSIST FUNCTION
Every ADC cycle generates interrupt
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Any value outside of threshold range
2 integration time periods out of range
3 integration time periods out of range
4 integration time eriods out of range
5 integration time eriods ut of range
6 integratitime periods out of range
7 integratioe priods out of ran
8 integration me periods out of rge
9 integration time periods out orange
1nteation time periodt of range
1 integration time eriodout of range
12 integration time perds out of range
13 integration tme priods out of range
14 integration timperiods out of range
15 integme periods out of range
ID Register (Ah)
The ID register provides the value for oth the part number and silicon revision number for that part number.
It is a read-only register, whose vnever changes.
Table 11. ID Register
7
6
−
5
−
4
−
3
2
1
−
0
−
ID
Ah
PARTNO
REVNO
Reset Value:
−
−
−
FIELD
PRTN
EVNO
BTS
7:4
DESCRIPTION
Part Number Identification: field value 1010 = TSL2568, field value 1011 = TSL2569
Revision number identification
3:0
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
15
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
ADC Channel Data Registers (Ch − Fh)
The ADC channel data are expressed as 16-bit values spread across two registers. The ADC channel 0 data
registers, DATA0LOW and DATA0HIGH provide the lower and upper bytes, respectively, of the ADC value of
channel 0. Registers DATA1LOW and DATA1HIGH provide the lower and upper bytes, respectively, of the ADC
value of channel 1. All channel data registers are read-only and default to 00h on power up.
Table 12. ADC Channel Data Registers
REGISTER
DATA0LOW
DATA0HIGH
DATA1LOW
DATA1HIGH
ADDRESS
BITS
7:0
DESCRIPTION
ADC channel 0 lower byte
Ch
Dh
Eh
Fh
7:0
ADC channel 0 upper byte
ADC channel 1 lower byte
ADC channel 1 upper byte
7:0
7:0
The upper byte data registers can only be read following a read to the corresponding lower be register. When
the lower byte register is read, the upper eight bits are strobed into a shadow register, whicis read by a
subsequent read to the upper byte. The upper register will read the correct value even iadditional ADC
integration cycles end between the reading of the lower and upper registers.
NOTE: The Read Word protocol can be used to read byte-paired registers. For ample, e DATA0LOW and DATA0HIGH registers (as well as
the DATA1LOW and DATA1HIGH registers) may be read together to obtath16-bit ADC value ia sigle transaction
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
16
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
APPLICATION INFORMATION: SOFTWARE
Basic Operation
After applying V , the device will initially be in the power-down state. To operate the device, issue a command
DD
to access the CONTROL register followed by the data value 03h to power up the device. At this point, both ADC
channels will begin a conversion at the default integration time of 400 ms. After 400 ms, the conversion results
will be available in the DATA0 and DATA1 registers. Use the following pseudo code to read the data registers:
// Read ADC Channels Using Read Word Protocol − RECOMMENDED
Address = 0x39
//Slave addr – also 0x29 or 0x49
//Address the Ch0 lower data register and configure for Read Word
Command = 0xAC
//Set Command bit and Word bit
//Reads two bytes from sequential registers 0x0C and 0x0D
//Results are returned in DataLow and DataHigh variables
ReadWord (Address, Command, DataLow, DataHigh)
Channel0 = 256 * DataHigh + DataLow
//Address the Ch1 lower data register and cofigure for Read Wd
Command = 0xAE
//St bit fields 7 ad 5
//Reads two bytes from sequential registers 0x0E and 0x0F
//Results are returned in DataLow and taHigh variables
ReadWord (Address, Command, DataLow, DHigh)
Channel1 = 256 * DataHigh + DataLow
//Shift DataHgh to upper byte
// Read ADC Channels Using Read Byte Potocol
Address = 0x39
//Sve addr − also 0x29 or 0x49
/Address the Ch0 lower data register
//sult returned in DataLow
/Address the Ch0 upper data register
//Result returned in DataHigh
Command = 0x8C
ReadByte (Address, Comman, DtaLow)
Command = 0x8D
ReadByte (Address, Commd, DataHigh)
Channel0 = 256 * DataH+ DataLow
//Shift DataHigh to upper byte
Command = 0x8E
ReadByte (Address, Command, DatLow
Command = 0x8F
ReadByte (Address, Command, DataHigh)
Channel1 = 256 * DataHigh + DtaLow
//Address the Ch1 lower data register
//Result returned in DataLow
//Address the Ch1 upper data register
//Result returned in DataHigh
//Shift DataHigh to upper byte
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
17
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
APPLICATION INFORMATION: SOFTWARE
Configuring the Timing Register
The command, timing, and control registers are initialized to default values on power up. Setting these registers
to the desired values would be part of a normal initialization or setup procedure. In addition, to maximize the
performance of the device under various conditions, the integration time and gain may be changed often during
operation. The following pseudo code illustrates a procedure for setting up the timing register for various
options:
// Set up Timing Register
//Low Gain (1x), integration time of 402ms (default value)
Address = 0x39
Command = 0x81
Data = 0x02
WriteByte(Address, Command, Data)
//Low Gain (1x), integration time of 101ms
Data = 0x01
WriteByte(Address, Command, Data)
//Low Gain (1x), integration time of 13.7ms
Data = 0x00
WriteByte(Address, Command, Data)
//High Gain (16x), integration time of 101
Data = 0x11
WriteByte(Address, Command, Data)
//Read data registers (see Basic Operation example)
//Perform Manual Integration
//Set up for manual integriowith Gain o1x
Data = 0x03
//Set manual integration me – device converting
WriteByte(Address, Command, Data)
//Begin integration period
Data = 0x0B
WriteByte(Address, Command, Dat)
//Integrate for 50ms
Sleep (50)
//Wait for 50ms
//Stop integrating
Data = 0x03
WriteByte(Address, Cmmand, Data)
//Read data regisers see Basic Operation example)
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
18
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
APPLICATION INFORMATION: SOFTWARE
Interrupts
The interrupt feature of the TSL256x device simplifies and improves system efficiency by eliminating the need
to poll the sensor for a light intensity value. Interrupt styles are determined by the INTR field in the Interrupt
Register. The interrupt feature may be disabled by writing a field value of 00h to the Interrupt Control Register
so that polling can be performed.
The versatility of the interrupt feature provides many options for interrupt configuration and usage. The primar
purpose of the interrupt function is to provide a meaningful change in light intensity. However, it also e used
as an end-of-conversion signal. The concept of a meaningful change can be defined by the user both in trms
of light intensity and time, or persistence, of that change in intensity. The TSL256x device implemets two
16-bit-wide interrupt threshold registers that allow the user to define a threshold above and below thurrent
light level. An interrupt will then be generated when the value of a conversion exceeds either of thee limits. For
simplicity of programming, the threshold comparison is accomplished only with Channel 0. Ths simplifies
calculation of thresholds that are based, for example, on a percent of the current light level. It is adequate to
use only one channel when calculating light intensity differences since, for a given lighsouce, the channel 0
and channel 1 values are linearly proportional to each other and thus both valuescae linearly with light
intensity.
To further control when an interrupt occurs, the TSL256devie provides an nterrupt persistence feature. This
feature allows the user to specify a number of cnversion cycles for which a light intensity exceeding either
interrupt threshold must persist before actually gating an interruThis can be used to prevent transient
changes in light intensity from generating an unanted interrupt. Wita value of 1, an interrupt occurs
immediately whenever either threshold is exceeded. With valueof , where N can range from 2 to 15, N
consecutive conversions must result in vaues outside the interrupt window for an interrupt to be generated. For
example, if N is equal to 10 and the integration time is 402 then an interrupt will not be generated unless
the light level persists for more than 4 seonds outside threshold.
Two different interrupt styles are aailable: Level and SMBus Alert. The difference between these two interrupt
styles is how they are cleardoth result in the inerrupt line going active low and remaining low until the
interrupt is cleared. A level stynterrupt is cleaby setting the CLEAR bit (bit 6) in the COMMAND register.
The SMBus Alert style interrupt is cleared by at Response as described in the Interrupt Control Register
section and SMBus specification.
To configure the interrupt as an end-of-conversion signal, the interrupt PERSIST field is set to 0. Either Level
or SMBus Alert style can be used. An interrupt will be generated upon completion of each conversion. The
interrupt threshold registers are gred. The following example illustrates the configuration of a level interrupt:
// Set up end−of−conversiointerrupt, Level style
Address = 0x39
Command = 0x86
Data = 0x10
//Slave addr also 0x29 or 0x49
//Address Interrupt Register
//Level style, every ADC cycle
WriteByte(AddessCommand, Data)
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
19
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
APPLICATION INFORMATION: SOFTWARE
The following example pseudo code illustrates the configuration of an SMB Alert style interrupt when the light
intensity changes 20% from the current value, and persists for 3 conversion cycles:
// Read current light level
Address = 0x39
Command = 0xAC
//Slave addr also 0x29 or 0x49
//Set Command bit and Word bit
ReadWord (Address, Command, DataLow, DataHigh)
Channel0 = (256 * DataHigh) + DataLow
//Calculate upper and lower thresholds
T_Upper = Channel0 + (0.2 * Channel0)
T_Lower = Channel0 – (0.2 * Channel0)
//Write the lower threshold register
Command = 0xA2
//Addr lower threshold reg, set Word it
WriteWord (Address, Command, T_Lower.LoByte, T_Lower.HiByte)
//Write the upper threshold register
Command = 0xA4
//Addr upper threshold reg, st Word bit
WriteWord (Address, Command, T_Upper.LoByte, T_per.HiByte)
//Enable interrupt
Command = 0x86
Data = 0x23
//Aress interrupt egister
/SMBAlert style, PERSIST = 3
WriteByte(Address, Command, Data)
In order to generate an interrupt on demand during system test or debu, a test mode (INTR = 11) can be used.
The following example illustrates how to geneate n interrupt on mand:
// Generate an interrupt
Address = 0x39
Command = 0x86
Data = 0x30
//lavaddr also 0x29 or 0x49
/Adress Interrupt register
/Test interrupt
WriteByte(Address, CommandData)
//Interrupt line should now be low
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
20
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
APPLICATION INFORMATION: SOFTWARE
Calculating Lux
The TSL256x is intended for use in ambient light detection applications such as display backlight control, where
adjustments are made to display brightness or contrast based on the brightness of the ambient light, as
perceived by the human eye. Conventional silicon detectors respond strongly to infrared light, which the human
eye does not see. This can lead to significant error when the infrared content of the ambient light is high, such
as with incandescent lighting, due to the difference between the silicon detector response and the brightnes
perceived by the human eye.
This problem is overcome in the TSL256x through the use of two photodiodes. One of the photodides
(channel 0) is sensitive to both visible and infrared light, while the second photodiode (channel 1) isnsitive
primarily to infrared light. An integrating ADC converts the photodiode currents to digital outputs. Cnel 1
digital output is used to compensate for the effect of the infrared component of light on the chanel 0 digital
output. The ADC digital outputs from the two channels are used in a formula to obtain a value that aproximates
the human eye response in the commonly used Illuminance unit of Lux:
Chipscale Package
For 0 < CH1/CH0 ꢀ 0.35
For 0.35 < CH1/CH0 ꢀ 0.45
For 0.45 < CH1/CH0 ꢀ 0.52
For 0.52 < CH1/CH0 ꢀ 0.67
For 0.67 < CH1/CH0 ꢀ 0.85
For CH1/CH0 > 0.85
Lux = 0.00713 ꢁ CH0 − 0.00975 ꢁ CH1
Lux = 0.00813 ꢁ H0 − .01250 ꢁ CH1
Lux = 0.00935 ꢁ CH0 − .01521 ꢁ CH
Lux = 0.0039ꢁ CH0 − 0.00482 ꢁ CH1
Lux = 0.0033CH0 − 0.00396 CH1
Lux = 0
TMB Package
For 0 < CH1/CH0 ꢀ 0.35
For 0.35 < CH1/CH0 ꢀ 0.50
For 0.50 < CH1/CH0 ꢀ 0.60
For 0.60 < CH1/CH0 ꢀ 0.72
For 0.72 < CH1/CH0 ꢀ 0.85
For CH1/CH0 > 0.85
Lux 0.00763 ꢁ CH0 − 01031 ꢁ CH1
Lx = 0.00817 ꢁ CH0 − 0.01188 ꢁ CH1
Lux = 0.00723 ꢁ C0 − 0.01000 ꢁ CH1
Lux = 0.00573 ꢁ CH0 − 0.00750 ꢁ CH1
Lux = 0.002ꢁ CH0 − 0.00254 ꢁ CH1
Lux = 0
The formulas shown above were obtained by optical testing with fluorescent and incandescent light sources,
and apply only to open-air applicatios. Optical apertures (e.g. light pipes) will affect the incident light on the
device.
Simplified Lux Calculation
Below is the argument ad return value including source code (shown on following page) for calculating lux.
The source code is intended for embedded and/or microcontroller applications. Two individual code sets are
provided, one for thchipscale package and one for the TMB package. All floating point arithmetic operations
have been liminted since embedded controllers and microcontrollers generally do not support these types
of operations. ince floating point has been removed, scaling must be performed prior to calculating illuminance
if the intgration time is not 402 ms and/or if the gain is not 16ꢁ as denoted in the source code on the following
pages. This sequence scales first to mitigate rounding errors induced by decimal math.
xtern unsigned int CalculateLux(unsigned int iGain, unsigned int tInt, unsigned int
ch0, unsigned int ch1, int iType)
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
21
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
//****************************************************************************
//
// Copyright 2004−2008 TAOS, Inc.
//
// THIS CODE AND INFORMATION IS PROVIDED ”AS IS” WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
// Module Name:
// lux.cpp
//
//****************************************************************************
#define LUX_SCALE 16
#define RATIO_SCALE 9
// scale by 2^16
// scale ratio by 2^9
//−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
// Integration time scaling factors
//−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
#define CH_SCALE 10
// scale channel vaues by 2^10
#define CHSCALE_TINT0 0x7517
#define CHSCALE_TINT1 0x0fe7
// 322/11 * 2^CH_SCAL
// 322/81 * 2^ALE
//−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
// T Package coefficients
//−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
// For Ch1/Ch0=0.00 to 0.35:
//
//
Lux=0.00763*Ch0−0.01031*Ch1
// For Ch1/Ch0=0.35 to 0.50:
//
Lux=0.00817*Ch0−0.018*Ch1
//
// For Ch1/Ch0=0.50 to 0.60:
//
Lux=0.00723*Ch0−0.01000*Ch1
//
// For Ch1/Ch0=0.60 to 0.72:
//
Lux=0.00573*Ch0−0.00750*h1
//
// For Ch1/Ch0=0.72 to 0.85:
//
Lux=0.00216*Ch0−0.0025Ch1
//
// For Ch1/Ch0>0.85:
//
Lux/Ch0=0
//
//−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
#define K1T 0x00b
#define B1T 0x01f4
#define M1T 0x02a4
// 0.35 * 2^RATIO_SCALE
// 0.00763 * 2^LUX_SCALE
// 0.01031 * 2^LUX_SCALE
#define K2T x0100
#define B2T x0217
#definM2T x030a
// 0.50 * 2^RATIO_SCALE
// 0.00817 * 2^LUX_SCALE
// 0.01188 * 2^LUX_SCALE
#define K3T 0x0133
#define B3T 0x01da
#define M3T 0x028f
// 0.60 * 2^RATIO_SCALE
// 0.00723 * 2^LUX_SCALE
// 0.01000 * 2^LUX_SCALE
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
22
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
#define K4T 0x0171
#define B4T 0x0177
#define M4T 0x01ec
// 0.72 * 2^RATIO_SCALE
// 0.00573 * 2^LUX_SCALE
// 0.00750 * 2^LUX_SCALE
#define K5T 0x01b3
#define B5T 0x008d
#define M5T 0x00a6
// 0.85 * 2^RATIO_SCALE
// 0.00216 * 2^LUX_SCALE
// 0.00254 * 2^LUX_SCALE
#define K6T 0x01b3
#define B6T 0x0000
#define M6T 0x0000
// 0.85 * 2^RATIO_SCALE
// 0.00000 * 2^LUX_SCALE
// 0.00000 * 2^LUX_SCALE
//−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
// CS Package coefficients
//−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
// For Ch1/Ch0=0.00 to 0.35:
//
//
Lux=0.00713*Ch0−0.00975*Ch1
// For Ch1/Ch0=0.35 to 0.45:
//
Lux=0.00813*Ch0−0.01250*Ch1
//
// For Ch1/Ch0=0.45 to 0.52:
//
Lux=0.00935*Ch0−0.01521*Ch1
//
// For Ch1/Ch0=0.52 to 0.67:
//
Lux=0.00394*Ch0−0.00482*Ch1
//
// For Ch1/Ch0=0.67 to 0.85:
//
Lux=0.00337*Ch0−0.00396*Ch1
//
// For Ch1/Ch0>0.85:
//
Lux/Ch0=0
//
//−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
#define K1C 0x00b3
#define B1C 0x01d3
#define M1C 0x027f
// 0.35 * ATIO_SCALE
// 0.00713 2^LUX_SCALE
// 000975 * 2^LUX_SCALE
#define K2C 0x00e6
#define B2C 0x0214
#define M2C 0x0333
/ 0.45 * 2^RATIO_SCALE
// 0.00813 * 2^LUX_SCALE
/ 0.01250 * 2^LUX_SCALE
#define K3C 0x010a
#define B3C 0x0265
#define M3C 0x03e5
// 0.52 * 2^RATIO_SCALE
// 0.00935 * 2^LUX_SCALE
// 0.01521 * 2^LUX_SCALE
#define K4C 0x0157
#define B4C 00102
#define M4C 0x03c
// 0.67 * 2^RATIO_SCALE
// 0.00394 * 2^LUX_SCALE
// 0.00482 * 2^LUX_SCALE
#define K5C 0x0b3
#define B5C 0x00dd
#define 5C 0x0104
// 0.85 * 2^RATIO_SCALE
// 0.00337 * 2^LUX_SCALE
// 0.00396 * 2^LUX_SCALE
#defne K6C 0x01b3
#definB6C 0x0000
#define M6C 0x0000
// 0.85 * 2^RATIO_SCALE
// 0.00000 * 2^LUX_SCALE
// 0.00000 * 2^LUX_SCALE
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
23
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
// lux equation approximation without floating point calculations
//////////////////////////////////////////////////////////////////////////////
// Routine: unsigned int CalculateLux(unsigned int ch0, unsigned int ch0, int iType)
//
// Description: Calculate the approximate illuminance (lux) given the raw
//
//
//
channel values of the TSL2568. The equation if implemented
as a piece−wise linear approximation.
// Arguments: unsigned int iGain − gain, where 0:1X, 1:16X
//
unsigned int tInt − integration time, where 0:13.7mS, 1:100mS, 2:402mS,
//
3:Manual
//
//
//
unsigned int ch0 − raw channel value from channel 0 of TSL2568
unsigned int ch1 − raw channel value from channel 1 of TSL2568
unsigned int iType − package type (0:T, 1:CS)
//
// Return:
//
unsigned int − the approximate illuminance (lux)
//////////////////////////////////////////////////////////////////////////////
unsigned int CalculateLux(unsigned int iGain, unsigned int tInt, unsigned int ch0,
unsigned int ch1, int iType)
{
//−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
// first, scale the channel values dependon the gain nd integration time
// 16X, 402mS is nominal.
// scale if integration time is NOT 402 msec
unsigned long chScale;
unsigned long channel1;
unsigned long channel0;
switch (tInt)
{
case 0:
case 1:
// 13.7 msec
chScale = CSCLE_TINT0;
break;
01 msec
chScale = CHSCALE_TINT1;
break;
default:
chScale = (1 << C_SCALE);
break;
// assume no scaling
}
// scale if gain is NOT 16X
if (!iGain) chScale = cScale << 4;
// scale 1X to 16X
// scale the channel vlues
channel0 = (ch0 * chcale) >> CH_SCALE;
channel1 = (ch1 * chScale) >> CH_SCALE;
//−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
// find the raio of the channel values (Channel1/Channel0)
// protet aainst divide by zero
unsigned lng ratio1 = 0;
if (nnel0 != 0) ratio1 = (channel1 << (RATIO_SCALE+1)) / channel0;
// rond the ratio value
usigned long ratio = (ratio1 + 1) >> 1;
// is ratio <= eachBreak ?
unsigned int b, m;
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
24
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
switch (iType)
{
case 0:
// T package
if ((ratio >= 0) && (ratio <= K1T))
{b=B1T; m=M1T;}
else if (ratio <= K2T)
{b=B2T; m=M2T;}
else if (ratio <= K3T)
{b=B3T; m=M3T;}
else if (ratio <= K4T)
{b=B4T; m=M4T;}
else if (ratio <= K5T)
{b=B5T; m=M5T;}
else if (ratio > K6T)
{b=B6T; m=M6T;}
break;
case 1:
// CS package
if ((ratio >= 0) && (ratio <= K1C))
{b=B1C; m=M1C;}
else if (ratio <= K2C)
{b=B2C; m=M2C;}
else if (ratio <= K3C)
{b=B3C; m=M3C;}
else if (ratio <= K4C)
{b=B4C; m=M4C;}
else if (ratio <= K5C)
{b=B5C; m=M5C;}
else if (ratio > K6C
{b=B6C; m=M6C;}
break;
}
unsigned long temp;
unsigned long lux;
temp = ((channel0 * b) − (channel1 ;
// scale CS or T package
// round lsb (2^(LUX_SCALE−1))
temp += (1 << (LUX_SCALE−1);
// strip off fractional portion
lux = temp >> LUX_SCALE
return(lux);
}
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
25
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
APPLICATION INFORMATION: HARDWARE
Power Supply Decoupling and Application Hardware Circuit
The power supply lines must be decoupled with a 0.1 μF capacitor placed as close to the device package as
possible (Figure 16). The bypass capacitor should have low effective series resistance (ESR) and low effective
series inductance (ESI), such as the common ceramic types, which provide a low impedance path to ground
at high frequencies to handle transient currents caused by internal logic switching.
V
V
BUS
DD
0.1 ꢁ F
TSL2568/
TSL2569
R
P
R
P
R
PI
INT
SCL
SDA
Figure 16. Bus Pull-Up esisors
Pull-up resistors (Rp) maintain the SDAH and SCLH lat a high level wen the bus is free and ensure the
signals are pulled up from a low to a high level within threquired rise time. Fr a complete description of the
SMBus maximum and minimum Rp values, please reviw he SMBus Specification at
2
http://www.smbus.org/specs. For a complete desiption of I C maximm and minimum Rp values, please
2
review the I C Specification at http://www.semiconductors.philipsom.
A pull-up resistor (R ) is also required or te interrupt (INT), whch functions as a wired-AND signal in a similar
PI
fashion to the SCL and SDA lines. A typcal impedance value between 10 kΩ and 100 kΩ can be used. Please
note that while Figure 16 shows INT eing pulled up to V , the interrupt can optionally be pulled up to V
.
D
BUS
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
26
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
APPLICATION INFORMATION: HARDWARE
PCB Pad Layout
Suggested PCB pad layout guidelines for the TMB-6 surface mount package and CS chipscale package are
shown in Figure 17 and Figure 18.
3.80
0.90
0.90
0.25
0.70
0.70
0.70
2.60
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
Figure 17. Suggested -6 Package PCB Layout
0.50
0.50
6 ꢀ ꢂ 0.21
0.50
NOTES: A. All linear dimensions re imilimeters.
B. This drawing is subject change without notice.
Fgure 18. Suggested Chipscale Package PCB Layout
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
27
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
MECHANICAL DATA
PACKAGE CS
TOP VIEW
Six-Lead Chipscale Device
PIN OUT
BOTTOM VIEW
1398
171
6
5
4
1
2
3
203
465
1250
END VIEW
400 ꢃ 50
700 ꢃ 55
6 ꢀ 100
TYP 30ꢁ
BOTTOM VIEW
SIDE VIEW
375 ꢃ 30
6 ꢀ ꢂ 2ꢃ 30
500
1750
500
Pb
Lead Free
500
375 ꢃ 30
NOTES: A. All r dimensions are in micrometers. Dimension tolerance is 25 μm unless otherwise noted.
B. Sor bmps are formed of Sn (96.5%), Ag (3%), and Cu (0.5%).
. The top of the photodiode active area is 410 μm below the top surface of the package.
D. The layer above the photodiode is glass and epoxy with an index of refraction of 1.53.
E. This drawing is subject to change without notice.
Figure 19. Package CS — Six-Lead Chipscale Packaging Configuration
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
28
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
MECHANICAL DATA
PACKAGE TMB-6
TOP VIEW
Six-Lead Surface Mount Device
TOP VIEW
C
L
0.0745 Typ
1.90
0.31
PIN 1
0.694
Typ
R 0.20
6 Pls
C
L
2.60
1.30
PIN 4
3.80
Photo-Active Area
0.88
END VIEW
1.35
0.50
BOTTOM VIEW
0.90
TYP
0.90 TYP
0.60
TYP
0.30
YP
Pb
Lead Free
0.30
TYP
NOTES: A. All linear dimensions are imilmeters. Dimension tolerance is 0.20 mm unless otherwise noted.
B. The photo-active area i1388 μm by 149 μm.
C. Package top suracis molded with an electrically nonconductive clear plastic compound having an index of refraction of 1.55.
D. Contact finish i0.5 μm minimum of soft gold plated over a 18 μm thick copper foil pattern with a 5 μm to 9 μm nickel barrier.
E. The underse of te package includes copper traces used to connect the pads during package substrate fabrication. Accordingly,
exposeaces and vias should not be placed under the footprint of the TMB package in a PCB layout.
F. This packe contains no lead (Pb).
G. Thdrawing is subject to change without notice.
igure 20. Package T — Six-Lead TMB Plastic Surface Mount Packaging Configuration
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
29
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
MECHANICAL DATA
TOP VIEW
2.00 ꢃ 0.05
1.75
ꢂ 1.50
4.00
4.00
B
+ 0.30
8.00
− 0.10
3.50 ꢃ 0.05
ꢂ 0.60
ꢃ 0.05
B
A
A
DETAIL B
DETAIL A
5ꢁ Max
5ꢁ Max
0.250
1.35 ꢃ 0.05
ꢃ
0
.
0
2
1.85 ꢃ 0.05
0.97 ꢃ 0.05
A
o
B
o
K
o
NOTES: A. All liner imesions are in millimeters. Dimension tolerance is 0.10 mm unless otherwise noted.
B. The dimesions on this drawing are for illustrative purposes only. Dimensions of an actual carrier may vary slightly.
C. Symbols on rawing A , B , and K are defined in ANSI EIA Standard 481−B 2001.
o
o
o
D. Eah reeis 178 millimeters in diameter and contains 3500 parts.
E. AOS packaging tape and reel conform to the requirements of EIA Standard 481−B.
n accordance with EIA standard, device pin 1 is located next to the sprocket holes in the tape.
G. This drawing is subject to change without notice.
Figure 21. TSL2568/TSL2569 Chipscale Carrier Tape
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
30
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
MECHANICAL DATA
2.10
0.30 ꢃ 0.050
SIDE VIEW
TOP VIEW
1.75 ꢃ 0.100
8 Typ
ꢂ 1.50
4 ꢃ 0.100
B
END VIEW
2 ꢃ 0.100
12 ꢃ 0.100
5.50
ꢃ 0.100
ꢂ 1.50
R 0.20 TYP
B
A
A
DETAL B
DETAIL A
2.90 ꢃ 0.100 A
o
3.09 MAX
R 0.20 TYP
R 0.20 TYP
4.29 MAX
4.10 ꢃ 0.100
B
o
1.80 K
o
NOTES: AAll liner dimensions are in millimeters.
BThdimensions on this drawing are for illustrative purposes only. Dimensions of an actual carrier may vary slightly.
C. Symbols on drawing A , B , and K are defined in ANSI EIA Standard 481−B 2001.
o
o
o
DEach reel is 178 millimeters in diameter and contains 1000 parts.
E. TAOS packaging tape and reel conform to the requirements of EIA Standard 481−B.
F. In accordance with EIA standard, device pin 1 is located next to the sprocket holes in the tape.
G. This drawing is subject to change without notice.
Figure 22. TSL2568/TSL2569 TMB Carrier Tape
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
31
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
MANUFACTURING INFORMATION
The CS and T packages have been tested and have demonstrated an ability to be reflow soldered to a PCB
substrate. The process, equipment, and materials used in these test are detailed below.
The solder reflow profile describes the expected maximum heat exposure of components during the solder
reflow process of product on a PCB. Temperature is measured on top of component. The components should
be limited to a maximum of three passes through this solder reflow profile.
Table 13. TSL2568/69 Solder Reflow Profile
PARAMETER
Average temperature gradient in preheating
Soak time
REFERENCE
TSL2568/69
2.5°C/sec
t
2 to 3 minutes
Max 60 sec
soak
Time above 217°C
t
1
Time above 230°C
t
Max 50 sec
2
Time above T
−10°C
t
Max 10 sec
peak
3
Peak temperature in reflow
T
260° C (−0°C/+5°C)
Max −5°C/sec
peak
Temperature gradient in cooling
Not to scale — for reference only
T
peak
T
3
T
T
2
1
Time (sec)
t
t
t
3
2
1
t
soak
Figure 23. TSL2568/TSL2569 Solder Reflow Profile Graph
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
32
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
MANUFACTURING INFORMATION
Tooling Required
D
D
Chipscale
− Solder stencil (square aperture size 0.210 mm, stencil thickness of 152 μm)
TMB
− Solder stencil (aperture size 0.70 mm x 0.90 mm, stencil thickness of 152 μm)
Process
1. Apply solder paste using stencil
2. Place component
3. Reflow solder/cure
4. X-Ray verify (recommended for chipscale only)
Additional Notes for Chipscale
Placement of the TSL2568/TSL2569 chipscale dee onto the gold immrsion substrate is accomplished using
a standard surface mount manufacturing process. Uing a 152-μm stecil with a 0.21 mm square aperture, print
solder paste onto the substrate. Machine-place the TSL2568/TSL2569 from the tape onto the substrate. A
suggest pick-up tool is the Siemens Vacuum Pckup tool noznumber 912. This nozzle has a rubber tip with
a diameter of approximately 0.75 mm. The part is picked up om the center of the body.
It is important to use a substrate hat has an immersion plaing surface. This may be immersion gold, solder,
or white tin. Hot air solder leveled (HASL) substrateare not coplanar, making them difficult to work with.
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
33
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
MANUFACTURING INFORMATION
Moisture Sensitivity
Optical characteristics of the device can be adversely affected during the soldering process by the release and
vaporization of moisture that has been previously absorbed into the package molding compound. To ensure the
package molding compound contains the smallest amount of absorbed moisture possible, each device is
dry-baked prior to being packed for shipping. Devices are packed in a sealed aluminized envelope with silica
gel to protect them from ambient moisture during shipping, handling, and storage before use.
The CS package has been assigned a moisture sensitivity level of MSL 2 and the devices should be stored under
the following conditions:
Temperature Range
Relative Humidity
Floor Life
5°C to 50°C
60% maximum
1 year out of bag at ambient < 30°C / 60% RH
Rebaking will be required if the aluminized envelope has been open for more than 1 year. If rebakig is required,
it should be done at 90°C for 3 hours.
The T package has been assigned a moisture sensitivity levof ML 3 and the devices should be stored under
the following conditions:
Temperature Range
Relative Humidity
Total Time
5°C to 50°C
60% maximum
6 months from the date code on the aluinized envelope — if unopened
168 hours or fewer
Opened Time
Rebaking will be required if the devices have ben stored unoned for more than 6 months or if the aluminized
envelope has been open for more than 168 ours. If rebaking is rquired, it should be done at 90°C for 4 hours.
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
34
www.taosinc.com
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
PRODUCTION DATA — information in this document is current at publication date. Products conform to
specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard
warranty. Production processing does not necessarily include testing of all parameters.
LEAD-FREE (Pb-FREE) and GREEN STATEMENT
Pb-Free (RoHS) TAOS’ terms Lead-Free or Pb-Free mean semiconductor products that are compatible with the current
RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneou
materials. Where designed to be soldered at high temperatures, TAOS Pb-Free products are suitable for use in specied
lead-free processes.
Green (RoHS & no Sb/Br) TAOS defines Green to mean Pb-Free (RoHS compatible), and free of Bromne ) and
Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material
Important Information and Disclaimer The information provided in this statement represents TAOS’ knowledge and
belief as of the date that it is provided. TAOS bases its knowledge and belief on information prvided by third parties,
and makes no representation or warranty as to the accuracy of such information. Efforts are unerwy to better integrate
information from third parties. TAOS has taken and continues to take reasonable stepto rovide representative
and accurate information but may not have conducted destrutive testing or chemical ansis n incoming materials and
chemicals. TAOS and TAOS suppliers consider certain infomation o be proprietary, and tus CAS numbers and other
limited information may not be available for release.
TICE
Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reerves the right to mke changes to the products contained in this
document to improve performance or for any other purpose, or to discontiue them without notice. Customers are advised
to contact TAOS to obtain the latest product informtion before plaorders or designing TAOS products into systems.
TAOS assumes no responsibility for the se of any products or circuits described in this document or customer product
design, conveys no license, either exessed or implied, undeany patent or other right, and makes no representation that
the circuits are free of patent infringmen. TAOS further mkes no claim as to the suitability of its products for any particular
purpose, nor does TAOS assume liability arising ot of te use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequor incidental damages.
TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR
USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY
RESULT IN PERSONAL INJURY OR DATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY
UNAUTHORIZED AND ANY SUCH USE Y A CUSTOMER IS COMPLETELY AT THE CUSTOMER’S RISK.
LUMENOLOGY, TAOS, the TAOlogoand Texas Advanced Optoelectronic Solutions are registered trademarks of Texas Advanced
Optoelectronic Solutions Incoporated.
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
www.taosinc.com
35
TSL2568, TSL2569
LIGHT-TO-DIGITAL CONVERTER
TAOS091D − DECEMBER 2008
Copyright E 2008, TAOS Inc.
The LUMENOLOGY r Company
r
r
36
www.taosinc.com
相关型号:
©2020 ICPDF网 联系我们和版权申明