AN-0982 [ADI]
The Residual Phase Noise Measurement; 残余相位噪声测量
| 型号： | AN-0982 |
| 厂家： | 
ADI |
| 描述： | The Residual Phase Noise Measurement |
| 文件： | 总4页 (文件大小：716K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AN-0982
APPLICATION NOTE
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
The Residual Phase Noise Measurement
by David Brandon and John Cavey
INTRODUCTION
BACKGROUND INFORMATION
This application note describes a technique to evaluate
DUT noise by removing external noise sources. A residual
phase noise setup is used to isolate and measure the additive
phase noise contribution of a device. Designers use this infor-
mation to select individual devices for their signal chain,
which, in aggregate, meet the phase noise requirements for
their complete system.
The setup shown in Figure 1 measures the additive phase noise
of the DUT. Note that two DUTs are used, each connected to a
common power supply and a common input clock. It will be
shown that the noise at each DUT output due to these common
noise sources is correlated. If the amplified DUT1 output signal
is denoted as E1 and the amplified and delayed DUT2 output
signal is denoted as E2, then the output phase noise can be
derived by simply modeling the phase detector as an analog
The benefit of a residual phase noise setup is that the effect of
noise sources external to the device under test (DUT), such
as power supplies or input clocks, can be canceled from the
measurement. Conversely, an absolute phase noise measure-
ment includes the impact of power supply noise and reference
clock noise.
multiplier with a gain of KPD
.
E1 = EC1 cos[ωCt + θM1 cos(ωMt)]
E2 = EC2 sin[ωCt + θM2 cos(ωMt)]
EOUT = LPF {KPDE1E2} = KPDEC1EC2 sin [(θM2 – θM1)cos(ωMt)]
The signal powers are assigned ECX and the magnitude of the
phase modulation (noise) is assigned θMX with carrier frequency
ωC and modulating (offset) frequency ωM. Because superposition
applies, the phase noise intrinsic to the DUTs can be neglected
when considering the phase noise from external sources.
This application note includes actual phase noise measurement
plots of a clocked device to highlight the attributes of the residual
phase noise setup. In addition, it demonstrates how the additive
phase noise of a device can be used to identify the source of
noise-related issues in the signal chain.
DUT POWER
SUPPLIES
CLOCK
SOURCE
DUT 1
DUT 2
AMP
PHASE
LPF
POWER
SPLITTER
SPECTRUM
LNA
0°
ANALYZER
DETECTOR
AMP
FREQUENCY
90°
Figure 1. Residual Phase Noise Measurement Setup
Rev. 0 | Page 1 of 1
AN-0982
Application Note
Considering the input clock signal phase noise and assuming
that DUT1 and DUT2 have identical excess phase transfer
functions, it is apparent by inspection that the portion of θM1
due to the clock source is equivalent to the portion of θM2 due
to the clock source. Similarly, the portion of θM1 due to the
power supplies is equivalent to the portion of θM2 due to the
power supplies. This phenomenon can be considered supply
pushing and is simply described by
gain and noise figure of the amplifiers resemble one another as
closely as possible.
Note that a DUT that requires clocking has a front-end amplifier
that exhibits a certain amount of noise. For this reason, a clock
source with a low slew rate could unintentionally increase the phase
noise contribution due to threshold uncertainty at the amplifier
input. When using a sinusoidal clock source, the maximum allowa-
ble amplitude, which maximizes the slew rate, should be used.
θM = KPVM
BASIC EXPERIMENT SETUP DETAILS
E1 = EC1 cos[ωCt + KP1VM cos(ωMt)]
E2 = EC2 cos[ωCt + KP2VM cos(ωMt)]
An experiment was performed using the setup shown in Figure 1.
Two DUTs with the same part number were chosen and clocked
by a single 1 GHz clock source. Both devices were set up to
divide the clock source frequency by 4 to produce a 250 MHz
output. In addition, the two output signals were adjusted so that
they were shifted in relative phase by 90° (quadrature), which
minimizes the down-converted signal level that appears at dc.
The magnitude of the phase modulation is given by the product
of the voltage noise on the supply and the pushing gain
(radians/V). Again, it is assumed that DUT1 and DUT2 have
equivalent pushing gains. As a result, these noise sources are
cancelled (theoretically) at the phase detector’s output, leaving
only the uncorrelated noise of the two DUTs for measurement.
The two DUT signals were amplified using a low noise amplifier
(LNA) to increase the dynamic range of the measurement system
(the phase noise contribution of the amplifiers is sufficiently low to
be ignored).
The intrinsic DUT noise can be ascertained with a few addi-
tional assumptions. Because the rms phase error due to device
noise is generally very small, the expression can be rewritten
for the output carrier using the small angle approximation as
Both amplifier outputs were sent to a balanced mixer (phase
detector). The phase detector mixes the two signals producing sum
and difference mixing products at the phase detector output. The
sum product was filtered out with a low-pass filter. The remaining
difference product constitutes the 250 MHz output signal down-
converted to dc (phase noise). The LNA in the setup provided
sufficient gain to overcome the noise floor limitation of the
spectrum analyzer.
Δθ = (θM2 – θM1) cos(ωMt)
EOUT ≈ K PD EC1EC2 Δθ,
Δθ <<
π
2
The output of the phase detector can be referred to as the
baseband signal since it has been demodulated. The actual
phase noise can be calculated once the phase detector gain
and the input signal power are determined assuming that the
amplifier phase noise contribution is negligible. Because the
noise intrinsic to each DUT is uncorrelated, it is assumed that
they contribute equally, such that the rms sum is the measured
output phase noise. For this reason, 3 dB is subtracted from the
phase noise measured on the spectrum analyzer (in dBc/Hz)
to ultimately determine the contribution of each DUT; this
representation is just the phase noise power relative to the
signal (carrier) power
COMMON CLOCK SOURCE PHASE NOISE
CANCELLATION IN A RESIDUAL PHASE NOISE
MEASUREMENT
Figure 2 shows the result of an absolute phase noise measurement
of two different clock sources. Clearly, the two clock sources
exhibit very different phase noise characteristics. Theoretically,
neither clock source should impact the DUTs additive phase noise
measured using a residual phase noise setup.
Figure 3 confirms this theory. Two separate residual phase
noise measurements were plotted with one trace for each clock
source. The two traces virtually overlap; this proves the cancel-
lation of the common clock source noise in the residual phase
noise setup. The clock source phase noise is not cancelled in an
absolute phase noise setup. In fact, if the DUTs are ideal (no
additive phase noise), their absolute phase noise curves match
the curves as shown in Figure 2. However, the curves would
measure 12 dB lower due to the factor of 4 frequency translation.
For example, normalized to a 250 MHz carrier, Clock Source 2
exhibits −92 dBc/Hz at 1 kHz offset, whereas the measured
DUT phase noise associated with Clock Source 2 is −135 dBc/Hz
at the same offset frequency, indicating approximately a 40 dB
suppression of the input clock phase noise in the residual
measurement.
E = EC sin[ωMt + Δθ] ≈ EC sin(ωMt) + EC Δθ cos Δθ(ωMt)
2
⎡
⎤
(
Δθ
2
)
L =10 log
⎢
⎣
⎥
⎦
When making very sensitive phase noise measurements, the
noise contribution of the amplifier may be significant. An
amplifier residual phase noise measurement can be performed
such that DUT1 and DUT2 are removed from Figure 1, with the
power splitter outputs applied directly to the amplifiers. The
amplifier input signal power should resemble the actual DUT
output signal in amplitude and slew rate. Using this procedure,
the measured amplifier phase noise can be root-sum-square
(rss) subtracted from the measured DUT phase noise to obtain
the precise DUT phase noise. Again, it is important that the
Rev. 0 | Page 2 of 2
Application Note
AN-0982
–90
–100
–110
–120
CLOCK SOURCE 1 WITH COMMON POWER SUPPLY
CLOCK SOURCE 2 WITH COMMON POWER SUPPLY
CLOCK SOURCE 1 WITH SEPARATE POWER SUPPLIES
–70
–90
CLOCK SOURCE 2
–110
–130
–150
–170
–130
–140
–150
CLOCK SOURCE 1
–160
–170
100
1k
10k
100k
1M
10M
100M
100
1k
10k
100k
1M
10M
100M
FREQUENCY OFFSET (MHz)
FREQUENCY OFFSET (MHz)
Figure 2. Absolute Phase Noise Measurement of Two Different Clock Sources
Figure 4. Residual Phase Noise Measurement Displays the Impact from
Common and Separate Power Supplies
–90
CLOCK SOURCE 1 WITH COMMON POWER SUPPLY
The same model (noisy) power supply is used for producing
Figure 3 and Figure 4. The measured phase noise impact of
this power supply becomes apparent when two separate power
supplies are used instead of a single common supply. In Figure 5,
the absolute phase noise is measured, this time using a new low
noise power supply. There is good agreement between the absolute
phase noise with low noise power supply and the residual phase
noise measurement with separate low noise power supplies.
Recall that in the residual phase noise measurement the input
clock phase noise is cancelled whereas in the absolute phase
noise measurement it is not.
CLOCK SOURCE 2 WITH COMMON POWER SUPPLY
–100
–110
–120
–130
–140
–150
–160
–170
–90
ABSOLUTE PN WITH LOW NOISE POWER SUPPLY
100
1k
10k
100k
1M
10M
100M
RESIDUAL PN WITH SEPARATED LOW NOISE SUPPLIES
FREQUENCY OFFSET (MHz)
–100
Figure 3. Residual Phase Noise Measurement with Virtually No Impact from
Either Clock Source in Figure 2
–110
–120
DEMONSTRATION OF COMMON POWER SUPPLY
NOISE CANCELLATION IN RESIDUAL PHASE NOISE
MEASUREMENT
–130
–140
–150
In Figure 3, the common power supply connection shown in
Figure 1 is used. In Figure 4, a separate power supply is used
for each DUT (that is, not a common supply). As a result, the
power supply noise is uncorrelated and, as shown, impacts the
residual phase noise measurement. In this case, the close-in phase
noise increases substantially when using separate power supplies.
–160
–170
100
1k
10k
100k
1M
10M
100M
FREQUENCY OFFSET (MHz)
Figure 5. Close-In Phase Noise Improvement Due to a Low Noise
Power Supply
Rev. 0 | Page 3 of 3
AN-0982
Application Note
The residual phase noise measurement is a valuable technique
used to identify the phase noise contribution of a single compo-
nent as part of a system design. Using this approach external
noise sources, such as the input clock signal noise and power
supply noise, can be effectively cancelled since these noise
contributors are correlated at each DUT in the measurement
setup. Furthermore, it is possible to account for the phase noise
contribution of buffers or amplifiers used in the DUT residual
noise measurement by performing additional residual phase
noise measurements on these components.
Combining residual and absolute phase noise measurements
is a powerful way to identify the dominant noise source in a
system design. Measurement data acquired on a frequency
divide-by-4 device has been presented which demonstrates the
concept and utility of the residual phase noise measurement. In
this example, the impact of a noisy input clock source and the
impact of a noisy power supply on the DUT has been quanti-
fied; from this evaluation, the system designer can derive
specifications for the input clock source and power supplies
based on actual measurement data.
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
AN07838-0-12/08(0)
Rev. 0 | Page 4 of 4
相关型号：
©2020 ICPDF网 联系我们和版权申明