ADP5034AREZ-R7 [ADI]
Dual 3 MHz, 1200mA Buck Regulator with Two 300 mA LDOs;型号: | ADP5034AREZ-R7 |
厂家: | ADI |
描述: | Dual 3 MHz, 1200mA Buck Regulator with Two 300 mA LDOs 开关 光电二极管 |
文件: | 总29页 (文件大小:782K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Dual 3 MHz, 1200 mA Buck
Regulators with Two 300 mA LDOs
ADP5034
Data Sheet
regulators operate in PWM mode when the load is above a pre-
defined threshold. When the load current falls below a predefined
threshold, the regulator operates in power save mode (PSM),
improving the light load efficiency.
FEATURES
Main input voltage range: 2.3 V to 5.5 V
Two 1200 mA buck regulators and two 300 mA LDOs
24-lead, 4 mm × 4 mm LFCSP or 28-lead TSSOP package
Regulator accuracy: 1.8%
Factory programmable or external adjustable VOUTx
3 MHz buck operation with forced PWM and auto PWM/PSM
modes
BUCK1/BUCK2: output voltage range from 0.8 V to 3.8 V
LDO1/LDO2: output voltage range from 0.8 V to 5.2 V
LDO1/LDO2: input supply voltage from 1.7 V to 5.5 V
LDO1/LDO2: high PSRR and low output noise
Table 1. Family Models
Maximum
Model
Channels
Current
Package
ADP5023 2 Buck,1 LDO
ADP5024 2 Buck,1 LDO
ADP5034 2 Buck,2 LDOs
ADP5037 2 Buck,2 LDOs
800 mA,
300 mA
1.2 A,
300 mA
1.2 A,
300 mA
800 mA,
300 mA
LFCSP (CP-24-10)
LFCSP (CP-24-10)
LFCSP (CP-24-10),
TSSOP (RE-28-1)
LFCSP (CP-24-10)
APPLICATIONS
ADP5033 2 Buck,2 LDOs with
2 EN pins
800 mA,
300 mA
WLCSP (CB-16-8)
Power for processors, ASICS, FPGAs, and RF chipsets
Portable instrumentation and medical devices
Space constrained devices
The two bucks operate out of phase to reduce the input capaci-
tor requirement. The low quiescent current, low dropout voltage,
and wide input voltage range of the ADP5034 LDOs extend the
battery life of portable devices. The ADP5034 LDOs maintain
power supply rejection greater than 60 dB for frequencies as
high as 10 kHz while operating with a low headroom voltage.
GENERAL DESCRIPTION
The ADP5034 combines two high performance buck regulators
and two low dropout (LDO) regulators. It is available in either a
24-lead 4 mm × 4 mm LFCSP or a 28-lead TSSOP package.
The high switching frequency of the buck regulators enables tiny
multilayer external components and minimizes the board space.
When the MODE pin is set to high, the buck regulators operate in
forced PWM mode. When the MODE pin is set to low, the buck
Regulators in the ADP5034 are activated through dedicated
enable pins. The default output voltages can be externally set in
the adjustable version, or factory programmable to a wide range
of preset values in the fixed voltage version.
TYPICAL APPLICATION CIRCUIT
AVIN
HOUSEKEEPING
C
0.1µF
AVIN
VOUT1
L1 1µH
VIN1
SW1
FB1
2.3V TO
5.5V
V
AT
OUT1
1200mA
C1
R1
R2
4.7µF
BUCK1
C5
10µF
PGND1
ON
EN1
EN1
OFF
MODE
PWM
MODE
PSM/PWM
VOUT2
VIN2
EN2
MODE
L2 1µH
SW2
FB2
C2
4.7µF
V
AT
OUT2
1200mA
R3
R4
BUCK2
C6
10µF
EN2
EN3
PGND2
EN3
VOUT3
FB3
V
AT
OUT3
300mA
LDO1
(ANALOG)
R5
R6
VIN3
1.7V TO
5.5V
C7
1µF
C3
1µF
EN4
ON
VOUT4
FB4
V
AT
EN4
OUT4
300mA
OFF
LDO2
(DIGITAL)
R7
R8
VIN4
C8
1µF
C4
1µF
ADP5034
AGND
Figure 1.
Rev. E
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rightsof third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2011–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADP5034* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
View a parametric search of comparable parts.
REFERENCE MATERIALS
Solutions Bulletins & Brochures
• Integrated Power Solutions for Altera FPGAs
• Integrated, High Power Solutions for Xilinx FPGAs
EVALUATION KITS
• ADP5034 Evaluation Board
DESIGN RESOURCES
• ADP5034 Material Declaration
• PCN-PDN Information
DOCUMENTATION
Application Notes
• AN-1311: Complex Power Supply Sequencing Made Easy
Data Sheet
• Quality And Reliability
• Symbols and Footprints
• ADP5034: Dual 3 MHz, 1200 mA Buck Regulators with Two
300 mA LDOs Data Sheet
DISCUSSIONS
View all ADP5034 EngineerZone Discussions.
User Guides
• UG-271: Evaluation Board for the ADP5023/ADP5024/
ADP5034/ADP5037 Micro Power Management Unit (PMU)
SAMPLE AND BUY
Visit the product page to see pricing options.
• UG-439: Evaluation Board for the ADP5034 TSSOP Micro
Power Management Unit (PMU)
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
TOOLS AND SIMULATIONS
• 5V uPMU BuckDesigner
• ADI Linear Regulator Design Tool and Parametric Search
• ADIsimPower™ Voltage Regulator Design Tool
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
ADP5034
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 16
Power Management Unit........................................................... 16
BUCK1 and BUCK2 .................................................................. 18
LDO1 and LDO2........................................................................ 19
Applications Information .............................................................. 20
Buck External Component Selection....................................... 20
LDO External Component Selection....................................... 22
Power Dissipation and Thermal Considerations ....................... 23
Buck Regulator Power Dissipation .......................................... 23
Junction Temperature ................................................................ 24
PCB Layout Guidelines.................................................................. 25
Typical Application Schematics.................................................... 26
Bill of Materials........................................................................... 26
Outline Dimensions....................................................................... 27
Ordering Guide .......................................................................... 28
Applications....................................................................................... 1
General Description ......................................................................... 1
Typical Application Circuit ............................................................. 1
Revision History ............................................................................... 3
Specifications..................................................................................... 4
General Specifications ................................................................. 4
BUCK1 and BUCK2 Specifications ........................................... 5
LDO1 and LDO2 Specifications................................................. 5
Input and Output Capacitor, Recommended Specifications.. 6
Absolute Maximum Ratings............................................................ 7
Thermal Resistance ...................................................................... 7
ESD Caution.................................................................................. 7
Pin Configuration and Function Descriptions............................. 8
Typical Performance Characteristics ............................................. 9
Rev. E | Page 2 of 28
Data Sheet
ADP5034
REVISION HISTORY
5/13—Rev. D to Rev. E
Change to Table 1, Low UVLO Input Voltage Falling Parameter,
Symbol Column.................................................................................3
Change to Table 2, Output Voltage Accuracy Parameter, Test
Conditions/Comment Column.......................................................4
Change to Table 2, Line Regulation Parameter, Symbols
Added Table 1; Renumbered Sequentially.....................................1
Changes to Figure 1...........................................................................1
Changes to NC Pin Description......................................................8
Changes to Figure 49 ......................................................................19
Changes to Figure 51 ......................................................................21
Changes to Figure 53 and Figure 54 .............................................26
Column...............................................................................................4
Change to Table 2, Load Regulation Parameter, Symbols
Column...............................................................................................4
Changes to Table 2, Reversed the RPFET and RNFET Symbols for
the SW On Resistance Parameter and Changes to Typ and Max
Columns .............................................................................................4
Changes to Table 3, Output Accuracy Parameter, Test
1/13—Rev. C to Rev. D
Changes to Ordering Guide...........................................................28
11/12—Rev. B to Rev. C
Changes to Ordering Guide...........................................................28
7/12—Rev. A to Rev. B
Conditions/Comments Column.....................................................4
Changes to Table 3, Line Regulation Parameter, Symbols
Column and Test Conditions/Comments Column......................4
Change to Table 3, Changes to Dropout Voltage Parameter and
Added Specification to Dropout Voltage Parameter....................5
Change to Table 3, Endnote 3..........................................................5
Change to Table 4, BUCK1, BUCK2 Output Capacitor
Parameter, Min Column Value........................................................5
Change to Table 4, Endnote 1..........................................................5
Changes to Absolute Maximum Ratings, Table 5.........................6
Changes to Table 7, Pin Function Descriptions............................7
Changes to TPC Section...................................................................8
Moved Power Dissipation and Thermal Considerations
Section ..............................................................................................22
Change to Equation 5 Where Statement......................................22
Change to Equation 6 .....................................................................22
Change to Undervoltage Lockout Section...................................16
Changes to Figure 46 ......................................................................16
Change to Figure 47........................................................................17
Changes to LDO1/LDO2 Section .................................................18
Changes to Output Capacitor Section and Table 8.....................19
Change to VRIPPLE Equation, Table 9, and Figure 50....................20
Changes to Input and Output Capacitor Properties Section ....21
Changes to Equation 3....................................................................22
Changes to Junction Temperature Section ..................................23
Changes to LDO Regulator Power Dissipation Section.............23
Changes to Figure 52 and Figure 53 .............................................25
Moved Bill of Materials Section ....................................................25
Changes to Ordering Guide...........................................................26
Added 28-Lead TSSOP Package Throughout ...............................1
Changes to Output Voltage Accuracy Parameter, Added TSSOP
SW On Resistance Specifications, Changes to Voltage Feedback
Minimum and Maximum Values, and Changes to Active Pull-
Down Conditions; Table 2 ...............................................................5
Changes to Output Voltage Accuracy Parameter and Voltage
Feedback Minimum and Maximum Values in Table 3; Changes
to Table 4 ............................................................................................6
Added Thermal Resistance Values for TSSOP Package, Table 6 ..7
Added Figure 3 and TSSOP Pins to Table 7 ..................................8
Changes to Figure 7, Figure 8, and Figure 9 ..................................9
Changes to Figure 10 ......................................................................10
Changes to Figure 18 Caption .......................................................11
Changes to Figure 31 and Figure 32 .............................................13
Changes to Figure 35 and Figure 39 Caption ..............................14
Changes to Undervoltage Lockout Section..................................17
Changes to Table 8 ..........................................................................20
Changes to Table 9 and Table 11 ...................................................21
Changes to Equation 9 and Following Paragraph.......................23
Added UG-349 to PCB Layout Guidelines Section....................25
Changes to Table 12 ........................................................................26
Updated Outline Dimensions........................................................27
Changes to Ordering Guide...........................................................28
10/11—Rev. 0 to Rev. A
Change to Features Section..............................................................1
Changes to General Description Section .......................................1
Changes to Figure 1...........................................................................1
6/11—Revision 0: Initial Version
Rev. E | Page 3 of 28
ADP5034
Data Sheet
SPECIFICATIONS
GENERAL SPECIFICATIONS
VAVIN = VIN1 = VIN2 = 2.3 V to 5.5 V; VIN3 = VIN4 = 1.7 V to 5.5 V; TJ = −40°C to +125°C for minimum/maximum specifications, and TA =
25°C for typical specifications, unless otherwise noted.
Table 2.
Parameter
Symbol
Test Conditions/Comments
Min
Typ
Max
Unit
INPUT VOLTAGE RANGE
THERMAL SHUTDOWN
Threshold
VAVIN, VIN1, VIN2
2.3
5.5
V
TSSD
TSSD-HYS
TJ rising
150
20
°C
°C
Hysteresis
START-UP TIME1
BUCK1, LDO1, LDO2
BUCK2
tSTART1
tSTART2
250
300
µs
µs
EN1, EN2, EN3, EN4, MODE INPUTS
Input Logic High
VIH
1.1
V
Input Logic Low
Input Leakage Current
INPUT CURRENT
VIL
VI-LEAKAGE
0.4
1
V
µA
0.05
All Channels Enabled
All Channels Disabled
VIN1 UNDERVOLTAGE LOCKOUT
High UVLO Input Voltage Rising
High UVLO Input Voltage Falling
Low UVLO Input Voltage Rising
Low UVLO Input Voltage Falling
ISTBY-NOSW
ISHUTDOWN
No load, no buck switching
TJ = −40°C to +85°C
108
0.3
175
1
µA
µA
UVLOVIN1RISE
UVLOVIN1FALL
UVLOVIN1RISE
UVLOVIN1FALL
3.9
V
V
V
V
3.1
2.275
1.95
1 Start-up time is defined as the time from EN1 = EN2 = EN3 = EN4 from 0 V to VAVIN to VOUT1, VOUT2, VOUT3, and VOUT4 reaching 90% of their nominal level. Start-up
times are shorter for individual channels if another channel is already enabled. See the Typical Performance Characteristics section for more information.
Rev. E | Page 4 of 28
Data Sheet
ADP5034
BUCK1 AND BUCK2 SPECIFICATIONS
VAVIN = VIN1 = VIN2 = 2.3 V to 5.5 V; TJ = −40°C to +125°C for minimum/maximum specifications, and TA = 25°C for typical
specifications, unless otherwise noted.1
Table 3.
Parameter
Symbol
Test Conditions/Comments
Min
Typ
Max
Unit
OUTPUT CHARACTERISTICS
Output Voltage Accuracy
ΔVOUT1/VOUT1
ΔVOUT2/VOUT2
(ΔVOUT1/VOUT1)/ΔVIN1
(ΔVOUT2/VOUT2)/ΔVIN2
(ΔVOUT1/VOUT1)/ΔIOUT1
(ΔVOUT2/VOUT2)/ΔIOUT2
,
PWM mode; ILOAD1 = ILOAD2 = 0 mA
PWM mode
−1.8
+1.8
%
Line Regulation
Load Regulation
,
−0.05
−0.1
0.5
%/V
%/A
V
,
ILOAD = 0 mA to 1200 mA, PWM mode
VOLTAGE FEEDBACK
OPERATING SUPPLY CURRENT
BUCK1 Only
VFB1, VFB2
Models with adjustable outputs
MODE = ground
ILOAD1 = 0 mA, device not switching, all
other channels disabled
ILOAD2 = 0 mA, device not switching, all
other channels disabled
ILOAD1 = ILOAD2 = 0 mA, device not switching,
LDO channels disabled
0.491
0.509
IIN
44
μA
μA
μA
mA
BUCK2 Only
IIN
55
BUCK1 and BUCK2
IIN
67
PSM CURRENT THRESHOLD
SW CHARACTERISTICS
SW On Resistance
IPSM
PSM to PWM operation
100
RNFET
RPFET
RNFET
RPFET
RNFET
RPFET
RNFET
RPFET
VIN1 = VIN2 = 3.6 V; LFCSP package
VIN1 = VIN2 = 3.6 V; LFCSP package
VIN1 = VIN2 = 5.5 V; LFCSP package
VIN1 = VIN2 = 5.5 V; LFCSP package
VIN1 = VIN2 = 3.6 V; TSSOP package
VIN1 = VIN2 = 3.6 V; TSSOP package
VIN1 = VIN2 = 5.5 V; TSSOP package
VIN1 = VIN2 = 5.5 V; TSSOP package
pFET switch peak current limit
VIN1= VIN2 = 3.6 V; Channel disabled
155
205
137
162
156
194
137
154
1950
75
240
310
204
243
237
270
202
212
2300
mΩ
mΩ
mΩ
mΩ
mΩ
mΩ
mΩ
mΩ
mA
Ω
Current Limit
ILIMIT1, ILIMIT2
RPDWN-B
fSW
1600
2.5
ACTIVE PULL-DOWN
OSCILLATOR FREQUENCY
3.0
3.5
MHz
1 All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC).
LDO1 AND LDO2 SPECIFICATIONS
VIN3 = (VOUT3 + 0.5 V) or 1.7 V (whichever is greater) to 5.5 V, VIN4 = (VOUT4 + 0.5 V) or 1.7 V (whichever is greater) to 5.5 V; CIN = COUT
1 µF; TJ = −40°C to +125°C for minimum/maximum specifications, and TA = 25°C for typical specifications, unless otherwise noted.1
=
Table 4.
Parameter
Symbol
Test Conditions/Comments
Min
Typ
Max
Unit
INPUT VOLTAGE RANGE
OPERATING SUPPLY CURRENT
Bias Current per LDO2
VIN3, VIN4
1.7
5.5
V
IVIN3BIAS/IVIN4BIAS
IOUT3 = IOUT4 = 0 µA
IOUT3 = IOUT4 = 10 mA
IOUT3 = IOUT4 = 300 mA
10
60
165
30
100
245
µA
µA
µA
IIN
Total System Input Current
Includes all current into AVIN, VIN1, VIN2, VIN3,
and VIN4
LDO1 or LDO2 Only
LDO1 and LDO2 Only
IOUT3 = IOUT4 = 0 µA, all other channels disabled
IOUT3 = IOUT4 = 0 µA, buck channels disabled
53
74
µA
µA
Rev. E | Page 5 of 28
ADP5034
Data Sheet
Parameter
Symbol
Test Conditions/Comments
Min
Typ
Max
Unit
OUTPUT CHARACTERISTICS
Output Voltage Accuracy
ΔVOUT3/VOUT3
ΔVOUT4/VOUT4
,
100 µA < IOUT3 < 300 mA, 100 µA < IOUT4
300 mA
<
−1.8
+1.8
%
Line Regulation
(ΔVOUT3/VOUT3)/ΔVIN3
(ΔVOUT4/VOUT4)/ΔVIN4
(ΔVOUT3/VOUT3)/ΔIOUT3
(ΔVOUT4/VOUT4)/ΔIOUT4
,
IOUT3 = IOUT4 = 1 mA
−0.03
+0.03 %/V
0.001 0.003 %/mA
Load Regulation3
,
IOUT3 = IOUT4 = 1 mA to 300 mA
VFB3, VFB4
VDROPOUT
VOLTAGE FEEDBACK
DROPOUT VOLTAGE4
0.491 0.5
0.509
140
V
VOUT3 = VOUT4 = 5.2 V, IOUT3 = IOUT4 = 300 mA
VOUT3 = VOUT4 = 3.3 V, IOUT3 = IOUT4 = 300 mA
VOUT3 = VOUT4 = 2.5 V, IOUT3 = IOUT4 = 300 mA
VOUT3 = VOUT4 = 1.8 V, IOUT3 = IOUT4 = 300 mA
50
75
100
180
mV
mV
mV
mV
mA
Ω
CURRENT-LIMIT THRESHOLD5
ACTIVE PULL-DOWN
OUTPUT NOISE
ILIMIT3, ILIMIT4
RPDWN-L
335
600
600
Channel disabled
Regulator LDO1
Regulator LDO2
NOISELDO1
NOISELDO2
PSRR
10 Hz to 100 kHz, VIN3 = 5 V, VOUT3 = 2.8 V
10 Hz to 100 kHz, VIN4 = 5 V, VOUT4 = 1.2 V
100
60
µV rms
µV rms
POWER SUPPLY REJECTION
RATIO
Regulator LDO1
Regulator LDO2
10 kHz, VIN3 = 3.3 V, VOUT3 = 2.8 V, IOUT3 = 1 mA
100 kHz, VIN3 = 3.3 V, VOUT3 = 2.8 V, IOUT3 = 1 mA
1 MHz, VIN3 = 3.3 V, VOUT3 = 2.8 V, IOUT3 = 1 mA
10 kHz, VIN4 = 1.8 V, VOUT4 = 1.2 V, IOUT4 = 1 mA
100 kHz, VIN4 = 1.8 V, VOUT4 = 1.2 V, IOUT4 = 1 mA
1 MHz, VIN4 = 1.8 V, VOUT4 = 1.2 V, IOUT4 = 1 mA
60
62
63
54
57
64
dB
dB
dB
dB
dB
dB
1 All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC).
2 This is the input current into VIN3/VIN4, which is not delivered to the output load.
3 Based on an endpoint calculation using 1 mA and 300 mA loads.
4 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only to output voltages
above 1.7 V.
5 Current-limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.0 V
output voltage is defined as the current that causes the output voltage to drop to 90% of 3.0 V, or 2.7 V.
INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS
TA = −40°C to +125°C, unless otherwise specified.
Table 5.
Parameter
Symbol
Min
Typ
Max
Unit
NOMINAL INPUT AND OUTPUT CAPACITOR RATINGS
BUCK1, BUCK2 Input Capacitor Ratings
BUCK1, BUCK2 Output Capacitor Ratings
LDO1, LDO21 Input and Output Capacitor Ratings
CAPACITOR ESR
CMIN1, CMIN2
CMIN1, CMIN2
CMIN3, CMIN4
RESR
4.7
10
1.0
40
40
µF
µF
µF
Ω
0.001
1
1 The minimum input and output capacitance should be greater than 1.0 µF over the full range of operating conditions. The full range of operating conditions in the
application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R- and X5R-type capacitors are
recommended; Y5V and Z5U capacitors are not recommended for use because of their poor temperature and dc bias characteristics.
Rev. E | Page 6 of 28
Data Sheet
ADP5034
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 6.
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Parameter
Rating
AVIN to AGND
VIN1, VIN2 to AVIN
PGND1, PGND2 to AGND
VIN3, VIN4, VOUT1, VOUT2, FB1, FB2,
FB3, FB4, EN1, EN2, EN3, EN4, MODE
to AGND
−0.3 V to +6 V
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to (AVIN + 0.3 V)
Table 7. Thermal Resistance
Package Type
θJA
35
36
θJC
3
5
Unit
°C/W
°C/W
24-Lead, 0.5 mm pitch LFCSP
28-Lead TSSOP
VOUT3 to AGND
VOUT4 to AGND
SW1 to PGND1
SW2 to PGND2
−0.3 V to (VIN3 + 0.3 V)
−0.3 V to (VIN4 + 0.3 V)
−0.3 V to (VIN1 + 0.3 V)
−0.3 V to (VIN2 + 0.3 V)
−65°C to +150°C
ESD CAUTION
Storage Temperature Range
Operating Junction Temperature
Range
−40°C to +125°C
Soldering Conditions
JEDEC J-STD-020
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
For detailed information on power dissipation, see the Power
Dissipation and Thermal Considerations section.
Rev. E | Page 7 of 28
ADP5034
Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
28
27
26
25
24
23
22
21
20
19
18
17
16
15
EN3
VIN4
VOUT4
NC
VIN3
VOUT3
FB3
3
4
NC
ADP5034
TOP VIEW
(Not to Scale)
5
FB4
AGND
AVIN
VIN1
SW1
PIN 1
6
EN4
INDICATOR
FB4
EN4
VIN2
SW2
PGND2
NC
1
2
3
4
5
6
18 AGND
17 AVIN
16 VIN1
15 SW1
14 PGND1
13 MODE
7
VIN2
SW2
PGND2
NC
ADP5034
8
TOP VIEW
9
PGND1
MODE
NC
(Not to Scale)
10
11
12
13
14
NC
EN2
EN1
FB2
FB1
VOUT2
VOUT1
NOTES
NOTES
1. NC = NOT INTERNALLY CONNECTED.
2. IT IS RECOMMENDED THAT THE EXPOSED PAD BE
SOLDERED TO THE GROUND PLANE.
1. NC = NOT INTERNALLY CONNECTED.
2. IT IS RECOMMENDED THAT THE EXPOSED PAD
BE SOLDERED TO THE GROUND PLANE.
Figure 2. LFCSP Pin Configuration—View from the Top of the Die
Figure 3. TSSOP Pin Configuration—View from the Top of the Die
Table 8. Pin Function Descriptions
Pin No.
LFCSP TSSOP
Mnemonic Description
1
5
FB4
LDO2 Feedback Input. For device models with an adjustable output voltage, connect this pin to the
middle of the LDO2 resistor divider. For device models with a factory programmed output voltage,
connect FB4 to the top of the capacitor on VOUT4.
2
3
4
5
6
6
7
8
9
EN4
LDO2 Enable Pin. High level turns on this regulator, and low level turns it off.
BUCK2 Input Supply (2.3 V to 5.5 V). Connect VIN2 to VIN1 and AVIN.
BUCK2 Switching Node.
Dedicated Power Ground for BUCK2.
No Connect. Leave this pin unconnected or connect to ground.
VIN2
SW2
PGND2
NC
4, 10, 11,
18, 25
7
8
12
13
EN2
FB2
BUCK2 Enable Pin. High level turns on this regulator, and low level turns it off.
BUCK2 Feedback Input. For device models with an adjustable output voltage, connect this pin to the
middle of the BUCK2 resistor divider. For device models with a fixed output voltage, leave this pin
unconnected.
9
10
11
14
15
16
VOUT2
VOUT1
FB1
BUCK2 Output Voltage Sensing Input. Connect VOUT2 to the top of the capacitor on VOUT2.
BUCK1 Output Voltage Sensing Input. Connect VOUT1 to the top of the capacitor on VOUT1.
BUCK1 Feedback Input. For device models with an adjustable output voltage, connect this pin to the
middle of the BUCK1 resistor divider. For device models with a fixed output voltage, leave this pin
unconnected.
12
13
17
19
EN1
MODE
BUCK1 Enable Pin. High level turns on this regulator, and low level turns it off.
BUCK1/BUCK2 Operating Mode. MODE = high: forced PWM operation. MODE = low: auto PWM/PSM
operation.
14
15
16
17
18
19
20
21
22
23
24
26
PGND1
SW1
VIN1
AVIN
AGND
FB3
Dedicated Power Ground for BUCK1.
BUCK1 Switching Node.
BUCK1 Input Supply (2.3 V to 5.5 V). Connect VIN1 to VIN2 and AVIN.
Analog Input Supply (2.3 V to 5.5 V). Connect AVIN to VIN1 and VIN2.
Analog Ground.
LDO1 Feedback Input. For device models with an adjustable output voltage, connect this pin to the
middle of the LDO1 resistor divider. For device models with a factory programmed output voltage,
connect FB3 to the top of the capacitor on VOUT3.
20
21
22
23
24
EPAD
27
28
1
2
3
VOUT3
VIN3
EN3
VIN4
VOUT4
EP
LDO1 Output Voltage.
LDO1 Input Supply (1.7 V to 5.5 V).
LDO1 Enable Pin. High level turns on this regulator, and low level turns it off.
LDO2 Input Supply (1.7 V to 5.5 V).
LDO2 Output Voltage.
EPAD
Exposed Pad. It is recommended that the exposed pad be soldered to the ground plane.
Rev. E | Page 8 of 28
Data Sheet
ADP5034
TYPICAL PERFORMANCE CHARACTERISTICS
VIN1 = VIN2 = VIN3= VIN4 = 3.6 V, TA = 25°C, unless otherwise noted.
3.320
3.315
3.310
3.305
3.300
3.295
3.290
3.285
3.280
3.275
3.270
140
120
100
80
T
T
= –40°C
= +25°C
A
A
60
T
= +85°C
40
A
20
0
2.3
2.8
3.3
3.8
4.3
4.8
5.3
0
0.2
0.4
0.6
(A)
0.8
1.0
1.2
I
INPUT VOLTAGE (V)
OUT
Figure 4. System Quiescent Current vs. Input Voltage, VOUT1 = 3.3 V,
OUT2 = 1.8 V, VOUT3 = 1.2 V, VOUT4 = 3.3 V, All Channels Unloaded
Figure 7. BUCK1 Load Regulation Across Temperature,
V
VIN = 4.2 V, VOUT1 = 3.3 V, PWM Mode
1.812
1.810
1.808
1.806
1.804
1.802
1.800
1.798
T
T
T
= –40°C
= +25°C
A
SW
4
2
IOUT
A
VOUT
EN
1
3
T
= +85°C
0.6
A
B
B
B
CH1 2.00V
CH3 5.00V
CH2 50.0mA Ω
CH4 5.00V
M 40.0µs
A CH3
2.2V
W
W
W
W
0
0.2
0.4
0.8
1.0
1.2
B
I (A)
OUT
T
11.20%
Figure 5. BUCK1 Startup, VOUT1 = 1.8 V, IOUT1 = 5 mA
Figure 8. BUCK2 Load Regulation Across Temperature,
VIN = 3.6 V, VOUT2 = 1.8 V, PWM Mode
0.808
0.807
0.806
0.805
0.804
0.803
0.802
T
SW
4
IOUT
T
T
= +25°C
= +85°C
A
2
T
= –40°C
A
A
VOUT
EN
1
3
B
B
B
B
CH1 2.00V
CH3 5.00V
CH2 50.0mA Ω
CH4 5.00V
M 40.0µs
A CH3
2.2V
W
W
W
0
0.2
0.4
0.6
0.8
1.0
1.2
W
I
(A)
OUT
T
11.20%
Figure 9. BUCK1 Load Regulation Across Input Voltage,
IN = 3.6 V, VOUT1 = 0.8 V, PWM Mode
Figure 6. BUCK2 Startup, VOUT2 = 3.3 V, IOUT2 = 10 mA
V
Rev. E | Page 9 of 28
ADP5034
Data Sheet
100
100
90
80
70
60
50
40
30
20
10
0
V
= 3.9V
IN
V
= 3.6V
IN
90
80
70
60
50
40
30
20
10
0
V
= 4.2V
V
= 2.3V
IN
IN
V
= 5.5V
V
= 5.5V
IN
IN
V
= 4.2V
IN
0.001
0.01
0.1
1
0.001
0.01
0.1
1
I
(A)
I
(A)
OUT
LOAD
Figure 13. BUCK2 Efficiency vs. Load Current, Across Input Voltage,
OUT2 = 1.8 V, PWM Mode
Figure 10. BUCK1 Efficiency vs. Load Current, Across Input Voltage,
OUT1 = 3.3 V, Auto Mode
V
V
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
V
= 5.5V
IN
V
= 3.9V
IN
V
= 2.3V
IN
V
= 5.5V
IN
V
= 4.2V
IN
V
= 3.6V
IN
V
= 4.2V
IN
0.001
0.01
0.1
1
0.001
0.01
0.1
1
I
(A)
I
(A)
OUT
OUT
Figure 14. BUCK1 Efficiency vs. Load Current, Across Input Voltage,
OUT1 = 0.8 V, Auto Mode
Figure 11. BUCK1 Efficiency vs. Load Current, Across Input Voltage,
OUT1 = 3.3 V, PWM Mode
V
V
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
V
= 3.6V
IN
V
= 2.3V
IN
V
= 2.3V
IN
V
= 5.5V
IN
V
= 4.2V
IN
V
= 5.5V
IN
V
= 3.6V
IN
V
= 4.2V
IN
0.001
0.01
0.1
1
0.001
0.01
0.1
1
I
(A)
I
(A)
OUT
OUT
Figure 15. BUCK1 Efficiency vs. Load Current, Across Input Voltage,
OUT1 = 0.8 V, PWM Mode
Figure 12. BUCK2 Efficiency vs. Load Current, Across Input Voltage,
OUT2 = 1.8 V, Auto Mode
V
V
Rev. E | Page 10 of 28
Data Sheet
ADP5034
100
90
80
70
60
50
40
30
3.3
3.2
3.1
3.0
2.9
2.8
2.7
2.6
2.5
–40°C
+25°C
+85°C
20
+25°C
+85°C
–40°C
10
0
0.001
0.01
0.1
1
0
0.2
0.4
0.6
(A)
0.8
1.0
1.2
I
(A)
I
OUT
OUT
Figure 19. BUCK2 Switching Frequency vs. Output Current, Across
Temperature, VOUT2 = 1.8 V, PWM Mode
Figure 16. BUCK1 Efficiency vs. Load Current, Across Temperature,
IN = 3.9 V, VOUT1 = 3.3 V, Auto Mode
V
100
90
80
70
60
50
40
30
20
10
0
T
+85°C
+25°C
VOUT
1
–40°C
I
SW
2
SW
4
0.001
0.01
0.1
1
CH1 50.0mV
CH2 500mA Ω
CH4 2.00V
M 4.00µs A CH2
28.40%
240mA
I
(A)
OUT
T
Figure 17. BUCK2 Efficiency vs. Load Current, Across Temperature,
OUT2 = 1.8 V, Auto Mode
Figure 20. Typical Waveforms, VOUT1 = 3.3 V, IOUT1 = 30 mA, Auto Mode
V
100
90
80
70
60
50
40
30
20
10
0
T
+25°C
VOUT
1
+85°C
–40°C
I
SW
2
SW
4
B
CH1 50.0mV
W CH2 500mA Ω
CH4 2.00V
M 4.00µs A CH2
220mA
0.001
0.01
0.1
1
B
W
I
(A)
OUT
T 28.40%
Figure 21. Typical Waveforms, VOUT2 = 1.8 V, IOUT2 = 30 mA, Auto Mode
Figure 18. BUCK1 Efficiency vs. Load Current, Across Temperature,
OUT1 = 0.8 V, Auto Mode
V
Rev. E | Page 11 of 28
ADP5034
Data Sheet
T
T
VOUT
1
2
VIN
I
SW
VOUT
SW
1
SW
4
3
4
B
B
CH1 50mV
CH2 500mA Ω
CH4 2.00V
M 400ns A CH2
220mA
CH1 50.0mV
CH3 1.00V
M 1.00ms
A
CH3
4.80V
W
W
W
B
B
B
W
CH4 2.00V
W
T
30.40%
T
28.40%
Figure 22. Typical Waveforms, VOUT1 = 3.3 V, IOUT1 = 30 mA, PWM Mode
Figure 25. BUCK2 Response to Line Transient, VIN2 = 4.5 V to 5.0 V,
OUT2 = 1.8 V, PWM Mode
V
T
T
SW
VOUT
1
4
1
I
SW
2
VOUT
SW
I
OUT
4
2
B
CH1 50mV
CH2 500mA Ω
CH4 2.00V
M 400ns A CH2
220mA
W
B
B
B
B
W
CH1 50.0mV
W CH2 50.0mA Ω
CH4 5.00V
M 20.0µs A CH2
T 60.000µs
356mA
W
W
T
28.40%
Figure 23. Typical Waveforms, VOUT2 = 1.8 V, IOUT2 = 30 mA, PWM Mode
Figure 26. BUCK1 Response to Load Transient, IOUT1 from 1 mA to 50 mA,
OUT1 = 3.3 V, Auto Mode
V
T
T
SW
4
1
VIN
VOUT
VOUT
1
SW
I
OUT
3
2
B
B
B
B
CH1 50.0mV
CH3 1.00V
M 1.00ms
A
CH3
4.80V
CH1 50.0mV
W CH2 50.0mA Ω
CH4 5.00V
M 20.0µs A CH2
379mA
W
W
W
W
B
B
CH4 2.00V
W
T
30.40%
T
22.20%
Figure 27. BUCK2 Response to Load Transient, IOUT2 from 1 mA to 50 mA,
OUT2 = 1.8 V, Auto Mode
Figure 24. BUCK1 Response to Line Transient, Input Voltage from 4.5 V to
5.0 V, VOUT1 = 3.3 V, PWM Mode
V
Rev. E | Page 12 of 28
Data Sheet
ADP5034
T
SW
EN
4
1
2
VOUT
VOUT
3
1
I
OUT
I
2
IN
B
B
B
CH1 50.0mV
W CH2 200mA Ω
CH4 5.00V
M 20.0µs A CH2
408mA
W
W
CH1 100mA CH2 5V
CH3 1V
M40µs 2.50GS/s
159.40µs
A
CH2
4.20V
T
T
20.40%
Figure 31. LDO Startup, VOUT3 = 1.8 V
Figure 28. BUCK1 Response to Load Transient, IOUT1 from 20 mA to 180 mA,
OUT1 = 3.3 V, Auto Mode
V
3.3160
3.3155
3.3150
3.3145
3.3140
3.3135
3.3130
3.3125
3.3120
3.3115
3.3110
T
SW
V
= 5.5V
IN
4
1
VOUT
V
V
= 4.2V
= 3.8V
IN
I
OUT
IN
2
0
50
100
150
(mA)
200
250
300
B
B
B
CH1 100mV
CH2 200mA Ω
CH4 5.00V
M 20.0µs A CH2
88.0mA
W
W
W
I
OUT
T
19.20%
Figure 32. LDO Load Regulation Across Input Voltage, VOUT3 = 3.3 V
Figure 29. BUCK2 Response to Load Transient, IOUT2 from 20 mA to 180 mA,
OUT2 = 1.8 V, Auto Mode
V
400
350
VOUT2
SW1
2
3
300
+125°C
250
200
150
100
50
+25°C
–40°C
VOUT1
SW2
1
4
B
B
B
0
2.3
CH1 5.00V
CH3 5.00V
CH2 5.00V
CH4 5.00V
M 400ns
50.00%
A
CH4
1.90V
W
W
2.8
3.3
3.8
4.3
4.8
5.3
B
W
W
T
INPUT VOLTAGE (V)
Figure 30. VOUT and SW Waveforms for BUCK1 and BUCK2 in PWM Mode
Showing Out-of-Phase Operation
Figure 33. LFCSP NMOS RDSON vs. Input Voltage Across Temperature
Rev. E | Page 13 of 28
ADP5034
Data Sheet
250
200
150
100
50
50
45
40
35
30
25
20
15
10
5
+125°C
+25°C
–40°C
0
2.3
0
2.8
3.3
3.8
4.3
4.8
5.3
0
0.05
0.10
0.15
0.20
0.25
INPUT VOLTAGE (V)
LOAD CURRENT (A)
Figure 34. LFCSP PMOS RDSON vs. Input Voltage Across Temperature
Figure 37. LDO Ground Current vs. Output Load, VIN3 = 3.3 V, VOUT3 = 2.8 V
1.802
T
1.801
1.800
1.799
1.798
1.797
1.796
1.795
1.794
1.793
1.792
T
= –40°C
= +25°C
A
A
I
OUT
2
1
T
VOUT
T
= +85°C
150
A
B
B
W
CH1 100mV
CH2 100mA Ω
M 40.0µs A CH2
52.0mA
W
0
50
100
200
250
300
I
(mA)
OUT
T
19.20%
Figure 35. LDO Load Regulation Across Temperature, VIN3 = 3.6 V, VOUT3 = 1.8 V
Figure 38. LDO Response to Load Transient, IOUT3 from 1 mA to 80 mA,
OUT3 = 2.8 V
V
3.0
I
= 10mA
I
= 100µA
OUT
OUT
T
I
= 1mA
OUT
= 100mA
= 150mA
2.5
2.0
1.5
1.0
0.5
0
I
OUT
I
VIN
OUT
= 300mA
I
OUT
VOUT
1
3
2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4
CH1 20.0mV
CH3 1.00V
M 100µs
28.40%
A
CH3
4.80V
V
(V)
IN
T
Figure 36. LDO Line Regulation Across Output Load, VOUT3 = 2.8 V
Figure 39. LDO Response to Line Transient, Input Voltage from 4.5 V to 5 V,
OUT3 = 2.8 V
V
Rev. E | Page 14 of 28
Data Sheet
ADP5034
60
55
50
45
0
V
= 5V
IN
–20
–40
–60
–80
V
= 3.3V
IN
40
35
30
100µA
1mA
10mA
50mA
100mA
150mA
–100
–120
25
0.001
0.01
0.1
1
10
100
10
100
1k
10k
100k
1M
10M
I
(mA)
FREQUENCY (Hz)
LOAD
Figure 40. LDO Output Noise vs. Load Current, Across Input Voltage,
OUT3 = 2.8 V
Figure 43. LDO PSRR Across Output Load, VIN3 = 3.3 V, VOUT3 = 3.0 V
V
65
60
0
100µA
1mA
10mA
50mA
100mA
150mA
V
= 5V
IN
–20
V
= 3.3V
IN
55
50
45
40
35
30
–40
–60
–80
–100
–120
25
0.001
0.01
0.1
1
10
100
10
100
1k
10k
100k
1M
10M
I
(mA)
FREQUENCY (Hz)
LOAD
Figure 41. LDO Output Noise vs. Load Current, Across Input Voltage,
OUT3 = 3.0 V
Figure 44. LDO PSRR Across Output Load, VIN3 = 5.0 V, VOUT3 = 2.8 V
V
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0
100µA
1mA
10mA
50mA
100mA
150mA
100µA
1mA
10mA
50mA
100mA
150mA
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 42. LDO PSRR Across Output Load, VIN3 = 3.3 V, VOUT3 = 2.8 V
Figure 45. LDO PSRR Across Output Load, VIN3 = 5.0 V, VOUT3 = 3.0 V
Rev. E | Page 15 of 28
ADP5034
Data Sheet
THEORY OF OPERATION
VOUT1 FB1 FB2 VOUT2
GM ERROR
AMP
GM ERROR
AMP
ENBK1
ENBK2
75Ω
75Ω
AVIN
PWM
COMP
PWM
COMP
SOFT START
SOFT START
VIN2
VIN1
I
I
LIMIT
LIMIT
PSM
PSM
COMP
COMP
PWM/
PSM
CONTROL
BUCK1
PWM/
PSM
CONTROL
BUCK2
LOW
CURRENT
LOW
CURRENT
SW2
SW1
OSCILLATOR
DRIVER
DRIVER
AND
ANTISHOOT
THROUGH
AND
SYSTEM
UNDERVOLTAGE
LOCKOUT
OP
MODE
ANTISHOOT
THROUGH
SEL
PGND2
600Ω
MODE2
THERMAL
SHUTDOWN
B
A
PGND1
ENLDO2
Y
MODE
EN1
EN2
EN3
EN4
ENBK1
ENABLE
AND
ENBK2
LDO
UNDERVOLTAGE
LOCKOUT
LDO
UNDERVOLTAGE
LOCKOUT
MODE
ENLDO1
ENLDO2
CONTROL
R1
R2
R3
LDO
CONTROL
LDO
AVIN
AVIN
CONTROL
ENLDO1
R4
600Ω
ADP5034
VIN3
AGND FB3 VOUT3 VIN4
FB4
VOUT4
Figure 46. Functional Block Diagram
This operating mode reduces the switching and quiescent
current losses. The auto PWM/PSM mode transition is
controlled independently for each buck regulator. The two
bucks operate synchronized to each other.
POWER MANAGEMENT UNIT
The ADP5034 is a micropower management unit (micro PMU)
combining two step-down (buck) dc-to-dc converters and two
low dropout linear regulators (LDOs). The high switching
frequency and tiny 24-lead LFCSP package allow for a small
power management solution.
The ADP5034 has individual enable pins (EN1 to EN4) control-
ling the activation of each regulator. The regulators are activated
by a logic level high applied to the respective EN pin. EN1 controls
BUCK1, EN2 controls BUCK2, EN3 controls LDO1, and EN4
controls LDO2.
To combine these high performance regulators into the micro
PMU, there is a system controller allowing them to operate
together.
Regulator output voltages are set through external resistor
dividers or can be optionally factory programmed to default
values (see the Ordering Guide section).
The buck regulators can operate in forced PWM mode if the
MODE pin is at a logic high level. In forced PWM mode, the
buck switching frequency is always constant and does not
change with the load current. If the MODE pin is at logic low
level, the switching regulators operate in auto PWM/PSM
mode. In this mode, the regulators operate at fixed PWM
frequency when the load current is above the PSM current
threshold. When the load current falls below the PSM current
threshold, the regulator in question enters PSM, where the
switching occurs in bursts. The burst repetition rate is a
function of the current load and the output capacitor value.
When a regulator is turned on, the output voltage ramp rate is
controlled through a soft start circuit to avoid a large inrush
current due to the charging of the output capacitors.
Rev. E | Page 16 of 28
Data Sheet
ADP5034
Thermal Protection
Alternatively, the user can select device models with a UVLO
set at a higher level, suitable for 5 V supply applications. For
these models, the device reaches the turn-off threshold when
the input supply drops to 3.65 V typical.
In the event that the junction temperature rises above 150°C,
the thermal shutdown circuit turns off all the regulators. Extreme
junction temperatures can be the result of high current opera-
tion, poor circuit board design, or high ambient temperature.
A 20°C hysteresis is included so that when thermal shutdown
occurs, the regulators do not return to operation until the on-chip
temperature drops below 130°C. When coming out of thermal
shutdown, all regulators restart with soft start control.
In case of a thermal or UVLO event, the active pull-downs (if
factory enabled) are enabled to discharge the output capacitors
quickly. The pull-down resistors remain engaged until the
thermal fault event is no longer present or the input supply
voltage falls below the VPOR voltage level. The typical value of
V
POR is approximately 1 V.
Undervoltage Lockout
Enable/Shutdown
To protect against battery discharge, undervoltage lockout
(UVLO) circuitry is integrated into the system. If the input
voltage on AVIN drops below a typical 2.15 V UVLO threshold,
all channels shut down. In the buck channels, both the power
switch and the synchronous rectifier turn off. When the voltage
on AVIN rises above the UVLO threshold, the part is enabled
once more.
The ADP5034 has an individual control pin for each regulator.
A logic level high applied to the ENx pin activates a regulator,
whereas a logic level low turns off a regulator.
Figure 47 shows the regulator activation timings for the
ADP5034 when all enable pins are connected to AVIN. Also
shown is the active pull-down activation.
V
UVLO
AVIN
V
POR
VOUT1
VOUT3
VOUT4
30µs
(MIN)
30µs
(MIN)
50µs (MIN)
VOUT2
50µs (MIN)
BUCK1,
LDO1,
LDO2
PULL-DOWNS
BUCK2
PULL-DOWN
Figure 47. Regulator Sequencing on the ADP5034 (EN1 = EN2 = EN3 = EN4 = VAVIN
)
Rev. E | Page 17 of 28
ADP5034
Data Sheet
drives the inductor to make the output voltage rise again to the
upper threshold. This process is repeated while the load current
is below the PSM current threshold.
BUCK1 AND BUCK2
The buck uses a fixed frequency and high speed current mode
architecture. The buck operates with an input voltage of 2.3 V
to 5.5 V.
The ADP5034 has a dedicated MODE pin controlling the PSM
and PWM operation. A high logic level applied to the MODE
pin forces both bucks to operate in PWM mode. A logic level
low sets the bucks to operate in auto PSM/PWM.
The buck output voltage is set through external resistor
dividers, shown in Figure 48 for BUCK1. The output voltage
can optionally be factory programmed to default values as
indicated in the Ordering Guide section. In this event, R1 and
R2 are not needed, and FB1 can be left unconnected. In all
cases, VOUT1 must be connected to the output capacitor. FB1
is 0.5 V.
PSM Current Threshold
The PSM current threshold is set to100 mA. The bucks employ
a scheme that enables this current to remain accurately
controlled, independent of input and output voltage levels. This
scheme also ensures that there is very little hysteresis between
the PSM current threshold for entry to and exit from the PSM.
The PSM current threshold is optimized for excellent efficiency
over all load currents.
VOUT1
VIN1
L1
1µH
SW1
VOUT1
BUCK
R1
R2
C5
10µF
FB1
Oscillator/Phasing of Inductor Switching
AGND
The ADP5034 ensures that both bucks operate at the same
switching frequency when both bucks are in PWM mode.
R1
R2
V
= V
FB1
+ 1
OUT1
Additionally, the ADP5034 ensures that when both bucks are in
PWM mode, they operate out of phase, whereby the Buck2
pFET starts conducting exactly half a clock period after the
BUCK1 pFET starts conducting.
Figure 48. BUCK1 External Output Voltage Setting
Control Scheme
The bucks operate with a fixed frequency, current mode PWM
control architecture at medium to high loads for high efficiency
but shift to a power save mode (PSM) control scheme at light
loads to lower the regulation power losses. When operating in
fixed frequency PWM mode, the duty cycle of the integrated
switches is adjusted and regulates the output voltage. When
operating in PSM at light loads, the output voltage is controlled
in a hysteretic manner, with higher output voltage ripple. During
part of this time, the converter is able to stop switching and
enters an idle mode, which improves conversion efficiency.
Short-Circuit Protection
The bucks include frequency foldback to prevent output current
runaway on a hard short. When the voltage at the feedback pin
falls below half the target output voltage, indicating the possi-
bility of a hard short at the output, the switching frequency is
reduced to half the internal oscillator frequency. The reduction
in the switching frequency allows more time for the inductor to
discharge, preventing a runaway of output current.
Soft Start
PWM Mode
The bucks have an internal soft start function that ramps the
output voltage in a controlled manner upon startup, thereby
limiting the inrush current. This prevents possible input voltage
drops when a battery or a high impedance power source is
connected to the input of the converter.
In PWM mode, the bucks operate at a fixed frequency of 3 MHz
set by an internal oscillator. At the start of each oscillator cycle,
the pFET switch is turned on, sending a positive voltage across
the inductor. Current in the inductor increases until the current
sense signal crosses the peak inductor current threshold that
turns off the pFET switch and turns on the nFET synchronous
rectifier. This sends a negative voltage across the inductor,
causing the inductor current to decrease. The synchronous
rectifier stays on for the rest of the cycle. The buck regulates the
output voltage by adjusting the peak inductor current threshold.
Current Limit
Each buck has protection circuitry to limit the amount of
positive current flowing through the pFET switch and the
amount of negative current flowing through the synchronous
rectifier. The positive current limit on the power switch limits
the amount of current that can flow from the input to the
output. The negative current limit prevents the inductor
current from reversing direction and flowing out of the load.
Power Save Mode (PSM)
The bucks smoothly transition to PSM operation when the load
current decreases below the PSM current threshold. When
either of the bucks enters PSM, an offset is induced in the PWM
regulation level, which makes the output voltage rise. When the
output voltage reaches a level approximately 1.5% above the
PWM regulation level, PWM operation is turned off. At this
point, both power switches are off, and the buck enters an idle
mode. The output capacitor discharges until the output voltage
falls to the PWM regulation voltage, at which point the device
100% Duty Operation
With a drop in input voltage, or with an increase in load
current, the buck may reach a limit where, even with the pFET
switch on 100% of the time, the output voltage drops below the
desired output voltage. At this limit, the buck transitions to a
mode where the pFET switch stays on 100% of the time. When
Rev. E | Page 18 of 28
Data Sheet
ADP5034
the input conditions change again and the required duty cycle
falls, the buck immediately restarts PWM regulation without
allowing overshoot on the output voltage.
Each LDO output voltage is set through external resistor dividers
as shown in Figure 49 for LDO1. The output voltage can option-
ally be factory programmed to default values as indicated in the
Ordering Guide section. In this event, Ra and Rb are not needed,
and FB3 must be connected to the top of the capacitor on VOUT3.
Active Pull-Downs
All regulators have optional, factory programmable, active pull-
down resistors discharging the respective output capacitors
when the regulators are disabled. The pull-down resistors are
connected between VOUTx and AGND. Active pull-downs are
disabled when the regulators are turned on. The typical value of
the pull-down resistor is 600 Ω for the LDOs and 75 Ω for the
bucks. Figure 47 shows the activation timings for the active
pull-downs during regulator activation and deactivation.
VOUT3
VOUT3
VIN3
C7
1µF
Ra
FB3
LDO1
Rb
Ra
Rb
V
= V
FB3
+ 1
OUT3
LDO1 AND LDO2
Figure 49. LDO1 External Output Voltage Setting
The ADP5034 contains two LDOs with low quiescent current
and low dropout linear regulators, and provides up to 300 mA
of output current. Drawing a low 10 μA quiescent current
(typical) at no load makes the LDO ideal for battery-operated
portable equipment.
The LDOs also provide high power supply rejection ratio
(PSRR), low output noise, and excellent line and load transient
response with only a small 1 µF ceramic input and output
capacitor.
Each LDO operates with an input voltage of 1.7 V to 5.5 V. The
wide operating range makes these LDOs suitable for cascading
configurations where the LDO supply voltage is provided from
one of the buck regulators.
LDO1 is optimized to supply analog circuits because it offers
better noise performance compared to LDO2. LDO1 should be
used in applications where noise performance is critical.
Rev. E | Page 19 of 28
ADP5034
Data Sheet
APPLICATIONS INFORMATION
Ceramic capacitors are manufactured with a variety of dielec-
trics, each with a different behavior over temperature and
applied voltage. Capacitors must have a dielectric adequate
to ensure the minimum capacitance over the necessary
temperature range and dc bias conditions. X5R or X7R
dielectrics with a voltage rating of 6.3 V or 10 V are recom-
mended for best performance. Y5V and Z5U dielectrics are
not recommended for use with any dc-to-dc converter because
of their poor temperature and dc bias characteristics.
BUCK EXTERNAL COMPONENT SELECTION
Trade-offs between performance parameters such as efficiency
and transient response can be made by varying the choice of
external components in the applications circuit, as shown in
Figure 1.
Feedback Resistors
For the adjustable model, referring to Figure 50 the total
combined resistance for R1 and R2 is not to exceed 400 kΩ.
Inductor
The worst-case capacitance accounting for capacitor variation
over temperature, component tolerance, and voltage is calcu-
lated using the following equation:
The high switching frequency of the ADP5034 bucks allows for
the selection of small chip inductors. For best performance, use
inductor values between 0.7 μH and 3 μH. Suggested inductors
are shown in Table 9.
C
EFF = COUT × (1 − TEMPCO) × (1 − TOL)
where:
EFF is the effective capacitance at the operating voltage.
The peak-to-peak inductor current ripple is calculated using
the following equation:
C
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
VOUT ×(VIN −VOUT
)
IRIPPLE
=
In this example, the worst-case temperature coefficient
(TEMPCO) over −40°C to +85°C is assumed to be 15% for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10%, and COUT is 9.2 μF at 1.8 V, as shown in Figure 50.
V
IN × fSW ×L
where:
SW is the switching frequency.
L is the inductor value.
f
Substituting these values in the equation yields
The minimum dc current rating of the inductor must be greater
than the inductor peak current. The inductor peak current is
calculated using the following equation:
CEFF = 9.2 μF × (1 − 0.15) × (1 − 0.1) ≈ 7.0 μF
To guarantee the performance of the bucks, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
12
IRIPPLE
2
IPEAK = ILOAD(MAX)
+
Inductor conduction losses are caused by the flow of current
through the inductor, which has an associated internal dc
resistance (DCR). Larger sized inductors have smaller DCR,
which may decrease inductor conduction losses. Inductor core
losses are related to the magnetic permeability of the core material.
Because the bucks are high switching frequency dc-to-dc
converters, shielded ferrite core material is recommended for
its low core losses and low EMI.
10
8
6
4
Output Capacitor
2
Higher output capacitor values reduce the output voltage ripple
and improve load transient response. When choosing this value,
it is also important to account for the loss of capacitance due to
output voltage dc bias.
0
0
1
2
3
4
5
6
DC BIAS VOLTAGE (V)
Figure 50. Capacitance vs. Voltage Characteristic
Table 9. Suggested 1.0 μH Inductors
Vendor
Model
Dimensions (mm)
2.0 × 1.6 × 0.9
2.5× 2.0 × 1.1
3.2 × 2.5 × 1.6
3.2 × 2.5 × 2.5
4.0 × 4.0 × 2.1
1.9 × 2.0 × 1.0
2.5 × 2.0 × 1.2
ISAT (mA)
1400
1500
2300
2000
5400
1800
1350
DCR (mΩ)
Murata
LQM2MPN1R0NG0B
LQM2HPN1R0MJ0L
LQH32PN1R0NN0
CBC3225T1R0MR
XFL4020-102ME
XPL2010-102ML
MDT2520-CN
85
90
45
71
11
89
85
Murata
Murata
Taiyo Yuden
Coilcraft®
Coilcraft
Toko
Rev. E | Page 20 of 28
Data Sheet
ADP5034
The peak-to-peak output voltage ripple for the selected output
capacitor and inductor values is calculated using the following
equation:
To minimize supply noise, place the input capacitor as close as
possible to the VINx pin of the buck. As with the output
capacitor, a low ESR capacitor is recommended.
IRIPPLE
8× fSW ×COUT
VIN
2 ×L×COUT
The effective capacitance needed for stability, which includes
temperature and dc bias effects, is a minimum of 3 µF and a
maximum of 10 µF. A list of suggested capacitors is shown in
Table 10 and Table 11.
VRIPPLE
=
≈
(
2π× fSW
)
Capacitors with lower effective series resistance (ESR) are
preferred to guarantee low output voltage ripple, as shown in
the following equation:
Table 10. Suggested 10 μF Capacitors
Voltage
Case Rating
VRIPPLE
IRIPPLE
ESRCOUT
≤
Vendor
Murata
TDK
Type Model
Size
(V)
X5R
X5R
GRM188R60J106
0603 6.3
0603 6.3
0603 6.3
0603 6.3
The effective capacitance needed for stability, which includes
temperature and dc bias effects, is a minimum of 7 µF and a
maximum of 40 µF.
C1608JB0J106K
JMK107BJ106MA-T
ECJ1VB0J106M
Taiyo Yuden X5R
Panasonic X5R
The buck regulators require 10 µF output capacitors to guaran-
tee stability and response to rapid load variations and to transition
into and out of the PWM/PSM modes. A list of suggested capaci-
tors is shown in Table 10. In certain applications where one or
both buck regulator powers a processor, the operating state is
known because it is controlled by software. In this condition,
the processor can drive the MODE pin according to the operating
state; consequently, it is possible to reduce the output capacitor
from 10 µF to 4.7 µF because the regulator does not expect a
large load variation when working in PSM mode (see Figure 51).
Table 11. Suggested 4.7 μF Capacitors
Voltage
Case Rating
Size (V)
GRM188R60J475ME19D 0402 6.3
Vendor
Type Model
X5R
Murata
Taiyo Yuden X5R
Panasonic X5R
JMK107BJ475
0402 6.3
0402 6.3
ECJ-0EB0J475M
Table 12. Suggested 1.0 μF Capacitors
Voltage
Case
Size
Rating
(V)
Input Capacitor
Vendor
Murata
Murata
TDK
Type Model
Higher value input capacitors help to reduce the input voltage
ripple and improve transient response. Maximum input
capacitor current is calculated using the following equation:
X5R
X5R
X5R
X5R
X5R
GRM155B30J105K
0402
6.3
GRM155R61A105KE15D 0402
10.0
6.3
C1005JB0J105KT
ECJ0EB0J105K
0402
0402
0402
Panasonic
6.3
VOUT (VIN −VOUT
)
ICIN ≥ ILOAD(MAX)
Taiyo
Yuden
LMK105BJ105MV-F
10.0
VIN
AVIN
VIN1
HOUSEKEEPING
BUCK1
C
0.1µF
AVIN
VOUT1
L1 1µH
2.3V TO
5.5V
SW1
FB1
V
@
OUT1
C1
1200mA
R1
R2
4.7µF
C5
10µF
ON
PGND1
EN1
VIN2
EN2
EN1
OFF
MODE
PWM
MODE
VOUT2
PSM/PWM
V
MODE
L2 1µH
R3
SW2
FB2
@
C2
4.7µF
OUT2
1200mA
BUCK2
EN2
C6
10µF
R4
PGND2
ON
OFF
OFF
VOUT3
FB3
EN3
V
@
OUT3
EN3
LDO1
300mA
R5
R6
VIN3
1.7V TO
5.5V
(ANALOG)
C7
1µF
C3
1µF
ON
EN4
VOUT4
FB4
V
@
EN4
OUT4
LDO2
(DIGITAL)
300mA
R7
R8
VIN4
C8
1µF
C4
1µF
ADP5034
AGND
Figure 51. Processor System Power Management with PSM/PWM Control
Rev. E | Page 21 of 28
ADP5034
Data Sheet
1.2
1.0
0.8
0.6
LDO EXTERNAL COMPONENT SELECTION
Feedback Resistors
For the adjustable model, the maximum value of Rb is not to
exceed 200 kΩ (see Figure 49).
Output Capacitor
The ADP5034 LDOs are designed for operation with small, space-
saving ceramic capacitors, but function with most commonly
used capacitors as long as care is taken with the ESR value. The
ESR of the output capacitor affects stability of the LDO control
loop. A minimum of 0.70 µF capacitance with an ESR of 1 Ω
or less is recommended to ensure that stability of the ADP5034.
Transient response to changes in load current is also affected by
output capacitance. Using a larger value of output capacitance
improves the transient response of the ADP5034 to large
changes in load current.
0.4
0.2
0
0
1
2
3
4
5
6
DC BIAS VOLTAGE (V)
Figure 52. Capacitance vs. Voltage Characteristic
Use the following equation to determine the worst-case capa-
citance accounting for capacitor variation over temperature,
component tolerance, and voltage:
Input Bypass Capacitor
Connecting a 1 µF capacitor from VIN3 and VIN4 to ground
reduces the circuit sensitivity to printed circuit board (PCB)
layout, especially when long input traces or high source imped-
ance is encountered. If greater than 1 µF of output capacitance
is required, increase the input capacitor to match it.
C
EFF = CBIAS × (1 − TEMPCO) × (1 − TOL)
where:
C
BIAS is the effective capacitance at the operating voltage.
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
Input and Output Capacitor Properties
Use any good quality ceramic capacitors with the ADP5034 as
long as they meet the minimum capacitance and maximum ESR
requirements. Ceramic capacitors are manufactured with a variety
of dielectrics, each with a different behavior over temperature
and applied voltage. Capacitors must have a dielectric adequate
to ensure the minimum capacitance over the necessary tempera-
ture range and dc bias conditions. X5R or X7R dielectrics with a
voltage rating of 6.3 V or 10 V are recommended for best perfor-
mance. Y5V and Z5U dielectrics are not recommended for use
with any LDO because of their poor temperature and dc bias
characteristics.
In this example, the worst-case temperature coefficient
(TEMPCO) over −40°C to +85°C is assumed to be 15% for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10%, and CBIAS is 0.85 μF at 1.8 V as shown in Figure 52.
Substituting these values into the following equation,
CEFF = 0.85 μF × (1 − 0.15) × (1 − 0.1) = 0.65 μF
Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over
temperature and tolerance at the chosen output voltage.
To guarantee the performance of the ADP5034, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
Figure 52 depicts the capacitance vs. voltage bias characteristic
of a 0402 1 µF, 10 V, X5R capacitor. The voltage stability of a capa-
citor is strongly influenced by the capacitor size and voltage rating.
In general, a capacitor in a larger package or with higher voltage
rating exhibits better stability. The temperature variation of the
X5R dielectric is about 15% over the −40°C to +85°C tempera-
ture range and is not a function of package or voltage rating.
Rev. E | Page 22 of 28
Data Sheet
ADP5034
POWER DISSIPATION AND THERMAL CONSIDERATIONS
The ADP5034 is a highly efficient µPMU, and, in most cases,
the power dissipated in the device is not a concern. However,
if the device operates at high ambient temperatures and maxi-
mum loading condition, the junction temperature can reach
the maximum allowable operating limit (125°C).
BUCK REGULATOR POWER DISSIPATION
The power loss of the buck regulator is approximated by
LOSS = PDBUCK + PL
where:
DBUCK is the power dissipation on one of the ADP5034 buck
P
(3)
P
When the temperature exceeds 150°C, the ADP5034 turns off
all the regulators, allowing the device to cool down. When the
die temperature falls below 130°C, the ADP5034 resumes
normal operation.
regulators.
PL is the inductor power losses.
The inductor losses are external to the device, and they do not
have any effect on the die temperature.
This section provides guidelines to calculate the power dissi-
pated in the device and ensure that the ADP5034 operates
below the maximum allowable junction temperature.
The inductor losses are estimated (without core losses) by
PL ≈ IOUT1(RMS)2 × DCRL
where:
DCRL is the inductor series resistance.
(4)
The efficiency for each regulator on the ADP5034 is given by
POUT
PIN
η =
×100%
(1)
IOUT1(RMS) is the rms load current of the buck regulator.
where:
η is the efficiency.
r
12
IOUT1(RMS) = IOUT1 × 1+
(5)
(6)
P
P
IN is the input power.
OUT is the output power.
where r is the normalized inductor ripple current.
r = VOUT1 × (1 − D)/(IOUT1 × L × fSW
where:
L is the inductance.
SW is the switching frequency.
)
Power loss is given by
P
LOSS = PIN − POUT
(2a)
(2b)
or
f
D is the duty cycle.
P
LOSS = POUT (1− η)/η
D = VOUT1/VIN1
(7)
Power dissipation can be calculated in several ways. The most
intuitive and practical is to measure the power dissipated at the
input and all the outputs. Perform the measurements at the
worst-case conditions (voltages, currents, and temperature).
The difference between input and output power is dissipated in
the device and the inductor. Use Equation 4 to derive the power
lost in the inductor and, from this, use Equation 3 to calculate
the power dissipation in the ADP5034 buck converter.
ADP5034 buck regulator power dissipation, PDBUCK, includes the
power switch conductive losses, the switch losses, and the transi-
tion losses of each channel. There are other sources of loss, but
these are generally less significant at high output load currents,
where the thermal limit of the application is. Equation 8
captures the calculation that must be made to estimate the
power dissipation in the buck regulator.
A second method to estimate the power dissipation uses the
efficiency curves provided for the buck regulator, and the power
lost on each LDO can be calculated using Equation 12. When
the buck efficiency is known, use Equation 2b to derive the total
power lost in the buck regulator and inductor, use Equation 4 to
derive the power lost in the inductor, and then calculate the
power dissipation in the buck converter using Equation 3. Add
the power dissipated in the buck and in the two LDOs to find
the total dissipated power.
P
DBUCK = PCOND + PSW + PTRAN
The power switch conductive losses are due to the output current,
OUT1, flowing through the P-MOSFET and the N-MOSFET
(8)
I
power switches that have internal resistance, RDSON-P and
RDSON-N. The amount of conductive power loss is found by
COND = [RDSON-P × D + RDSON-N × (1 − D)] × IOUT1(RMS)2
P
(9)
where RDSON-P is approximately 0.2 Ω, and RDSON-N is approxi-
mately 0.16 Ω at 25°C junction temperature and VIN1 = VIN2 =
3.6 V. At VIN1 = VIN2 = 2.3 V, these values change to 0.31 Ω and
0.21 Ω, respectively, and at VIN1 = VIN2 = 5.5 V, the values are
0.16 Ω and 0.14 Ω, respectively.
Note that the buck efficiency curves are typical values and may
not be provided for all possible combinations of VIN, VOUT, and
I
OUT. To account for these variations, it is necessary to include a
safety margin when calculating the power dissipated in the buck.
A third way to estimate the power dissipation is analytical and
involves modeling the losses in the buck circuit provided by
Equation 8 to Equation 11 and the losses in the LDO provided
by Equation 12.
Rev. E | Page 23 of 28
ADP5034
Data Sheet
Switching losses are associated with the current drawn by the
driver to turn on and turn off the power devices at the switching
frequency. The amount of switching power loss is given by
JUNCTION TEMPERATURE
In cases where the board temperature, TA, is known, the
thermal resistance parameter, θJA, can be used to estimate the
junction temperature rise. TJ is calculated from TA and PD using
the formula
P
SW = (CGATE-P + CGATE-N) × VIN12 × fSW
(10)
where:
C
C
GATE-P is the P-MOSFET gate capacitance.
GATE-N is the N-MOSFET gate capacitance.
TJ = TA + (PD × θJA)
(14)
Refer to Table 7 for the thermal resistance values of the LFCSP
and TSSOP packages. A very important factor to consider is
that θJA is based on a 4-layer 4 in × 3 in, 2.5 oz copper, as per
JEDEC standard, and real applications may use different sizes
and layers. It is important to maximize the copper used to remove
the heat from the device. Copper exposed to air dissipates heat
better than copper used in the inner layers. The exposed pad
should be connected to the ground plane with several vias.
For the ADP5034, the total of (CGATE-P + CGATE-N) is
approximately 150 pF.
The transition losses occur because the P-channel power
MOSFET cannot be turned on or off instantaneously, and the
SW node takes some time to slew from near ground to near
VOUT1 (and from VOUT1 to ground). The amount of transition
loss is calculated by
If the case temperature can be measured, the junction
temperature is calculated by
P
TRAN = VIN1 × IOUT1 × (tRISE + tFALL) × fSW
(11)
where tRISE and tFALL are the rise time and the fall time of the
switching node, SW. For the ADP5034, the rise and fall times of
SW are in the order of 5 ns.
TJ = TC + (PD × θJC)
(15)
where TC is the case temperature and θJC is the junction-to-case
thermal resistance provided in Table 7.
If the preceding equations and parameters are used for estimat-
ing the converter efficiency, it must be noted that the equations
do not describe all of the converter losses, and the parameter
values given are typical numbers. The converter performance
also depends on the choice of passive components and board
layout; therefore, a sufficient safety margin should be included
in the estimate.
When designing an application for a particular ambient
temperature range, calculate the expected ADP5034 power
dissipation (PD) due to the losses of all channels by using the
Equation 8 to Equation 13. From this power calculation, the
junction temperature, TJ, can be estimated using Equation 14.
The reliable operation of the converter and the two LDO regulators
can be achieved only if the estimated die junction temperature of
the ADP5034 (Equation 14) is less than 125°C. Reliability and
mean time between failures (MTBF) are highly affected by increas-
ing the junction temperature. Additional information about
product reliability can be found from the ADI Reliability Handbook,
which can be found at www.analog.com/reliability_handbook.
LDO Regulator Power Dissipation
The power loss of a LDO regulator is given by
P
DLDO = [(VIN − VOUT) × ILOAD] + (VIN × IGND
)
(12)
where:
ILOAD is the load current of the LDO regulator.
VIN and VOUT are input and output voltages of the LDO,
respectively.
GND is the ground current of the LDO regulator.
I
Power dissipation due to the ground current is small and it
can be ignored.
The total power dissipation in the ADP5034 simplifies to
PD = PDBUCK1 + PDBUCK2 + PDLDO1 + PDLDO2
(13)
Rev. E | Page 24 of 28
Data Sheet
ADP5034
PCB LAYOUT GUIDELINES
Poor layout can affect ADP5034 performance, causing electro-
magnetic interference (EMI) and electromagnetic compatibility
(EMC) problems, ground bounce, and voltage losses. Poor
layout can also affect regulation and stability. A good layout is
implemented using the following guidelines. Also, refer to the
UG-271 and UG-439 user guide.
•
•
Maximize the size of ground metal on the component side
to help with thermal dissipation.
Use a ground plane with several vias connecting to the
component side ground to further reduce noise
interference on sensitive circuit nodes.
•
Connect VIN1, VIN2, and AVIN together close to the IC
using short tracks.
•
Place the inductor, input capacitor, and output capacitor
close to the IC using short tracks. These components carry
high switching frequencies, and large tracks act as antennas.
Route the output voltage path away from the inductor and
SW node to minimize noise and magnetic interference.
•
Rev. E | Page 25 of 28
ADP5034
Data Sheet
TYPICAL APPLICATION SCHEMATICS
AVIN
HOUSEKEEPING
BUCK1
CAVIN
0.1µF
VOUT1
L1 1µH
VIN1
EN1
2.3V TO
5.5V
SW1
FB1
VOUT1
1200mA
@
C1
4.7µF
C5
ON
PGND1
10µF
EN1
OFF
MODE
PWM
MODE
VOUT2
PSM/PWM
VIN2
EN2
MODE
L2 1µH
R3
SW2
FB2
VOUT2
1200mA
@
C2
4.7µF
BUCK2
EN2
C6
10µF
PGND2
ON
OFF
OFF
EN3
VOUT3
FB3
VOUT3
300mA
@
EN3
LDO1
VIN3
1.7V TO
5.5V
(ANALOG)
C7
C3
1µF
1µF
EN4
ON
VOUT4
FB4
VOUT4
300mA
@
EN4
LDO2
(DIGITAL)
VIN4
C8
1µF
C4
1µF
ADP5034
AGND
Figure 53. ADP5034 Fixed Output Voltages with Enable Pins
AVIN
HOUSEKEEPING
C
0.1µF
AVIN
VOUT1
L1 1µH
VIN1
EN1
2.3V TO
5.5V
SW1
FB1
V
@
OUT1
C1
1200mA
R1
R2
BUCK1
MODE
4.7µF
C5
ON
PGND1
10µF
PSM/PWM
V
EN1
OFF
PWM
MODE
VOUT2
VIN2
EN2
MODE
L2 1µH
R3
SW2
FB2
@
C2
4.7µF
OUT2
1200mA
BUCK2
C6
10µF
R4
EN2
EN3
PGND2
ON
OFF
OFF
VOUT3
FB3
EN3
V
@
OUT3
LDO1
(ANALOG)
300mA
R5
R6
VIN3
1.7V TO
5.5V
C7
1µF
C3
1µF
ON
EN4
VOUT4
FB4
V
@
EN4
OUT4
LDO2
(DIGITAL)
300mA
R7
R8
VIN4
C8
1µF
C4
1µF
ADP5034
AGND
Figure 54. ADP5034 Adjustable Output Voltages with Enable Pins
BILL OF MATERIALS
Table 13.
Reference
Value
Part Number
Vendor
Package or Dimension (mm)
CAVIN
0.1 µF, X5R, 6.3 V
JMK105BJ104MV-F
LMK105BJ105MV-F
ECJ-0EB0J475M
JMK107BJ106MA-T
BRC1608T1R0M
LQM2MPN1R0NG0B
LQM2HPN1R0MJ0L
EPL2014-102ML
MDT2520-CN
Taiyo-Yuden
Taiyo-Yuden
Panasonic-ECG
Taiyo-Yuden
Taiyo-Yuden
Murata
0402
C3, C4, C7, C8
C1, C2
1 µF, X5R, 6.3 V
0402
4.7 µF, X5R, 6.3 V
0402
C5, C6
10 µF, X5R, 6.3 V
0603
L1, L2
1 µH, 0.18 Ω, 850 mA
1 µH, 0.085 Ω, 1400 mA
1 µH, 0.09 Ω, 1500 mA
1 µH, 0.059 Ω, 900 mA
1 µH, 0.086 Ω, 1350 mA
Four-regulator micro PMU
0603
2.0 × 1.6 × 0.9
2.5 × 2.0 × 1.1
2.0 × 2.0 × 1.4
2.5 × 2.0 × 1.2
24-lead LFCSP
Murata
Coilcraft
Toko
IC1
ADP5034
Analog Devices
Rev. E | Page 26 of 28
Data Sheet
ADP5034
OUTLINE DIMENSIONS
4.10
4.00 SQ
3.90
0.30
0.25
0.20
PIN 1
INDICATOR
PIN 1
INDICATOR
24
19
0.50
BSC
1
6
18
EXPOSED
PAD
2.20
2.10 SQ
2.00
13
12
7
0.50
0.40
0.30
0.25 MIN
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.80
0.75
0.70
0.05 MAX
0.02 NOM
SECTION OF THIS DATA SHEET.
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-WGGD-8.
Figure 55. 24-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
4 mm × 4 mm Body, Very Very Thin Quad
(CP-24-10)
Dimensions shown in millimeters
9.80
9.70
9.60
3.55
3.50
3.45
28
15
3.05
3.00
2.95
4.50
4.40
4.30
EXPOSED
6.40
PAD
BSC
(Pins Up)
1
14
TOP VIEW
BOTTOM VIEW
1.05
1.00
0.80
1.20 MAX
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
8°
0°
0.20
0.09
0.15
0.05
0.65 BSC
0.30
0.19
0.75
0.60
0.45
SEATING
PLANE
COPLANARITY
0.10
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-153-AET
Figure 55. 28-Lead Thin Shrink Small Outline with Exposed Pad Package [TSSOP_EP]
9.7 mm × 6.4 mm Body, (RE-28-1)
Dimensions shown in millimeters
Rev. E | Page 27 of 28
ADP5034
Data Sheet
ORDERING GUIDE
Temperature
Range
Output
Active Pull-
UVLO3 Down4
Package
Option
Model1
Voltage (V)2
Package Description
ADP5034ACPZ-R2
−40°C to +125°C Adjustable
Low
Low
Low
Enabled on buck
channels only
Enabled on buck
channels only
Enabled on buck
channels only
24-Lead Lead Frame Chip Scale Package
(LFCSP_WQ)
24-Lead Lead Frame Chip Scale Package
(LFCSP_WQ)
24-Lead Lead Frame Chip Scale Package
(LFCSP_WQ)
CP-24-10
CP-24-10
CP-24-10
ADP5034ACPZ-R7
−40°C to +125°C Adjustable
ADP5034ACPZ-1-R7
−40°C to +125°C VOUT1 = 1.2 V
VOUT2 = 3.3 V
VOUT3 = 2.8 V
VOUT4 = 1.8 V
ADP5034ACPZ-2-R7
ADP5034ACPZ-3-R7
ADP5034AREZ
−40°C to +125°C Adjustable
−40°C to +125°C Adjustable
−40°C to +125°C Adjustable
−40°C to +125°C Adjustable
−40°C to +125°C Adjustable
−40°C to +125°C Adjustable
High
High
Low
Low
High
High
Enabled on buck
channels only
Enabled on all
channels
Enabled on all
channels
Enabled on all
channels
Enabled on all
channels
Enabled on all
channels
24-Lead Lead Frame Chip Scale Package
(LFCSP_WQ)
24-Lead Lead Frame Chip Scale Package
(LFCSP_WQ)
CP-24-10
CP-24-10
RE-28-1
RE-28-1
RE-28-1
RE-28-1
28-Lead TSSOP Package (TSSOP_EP)
28-Lead TSSOP Package (TSSOP_EP)
28-Lead TSSOP Package (TSSOP_EP)
28-Lead TSSOP Package (TSSOP_EP)
ADP5034AREZ-R7
ADP5034AREZ-1
ADP5034AREZ-1-R7
ADP5034-1-EVALZ
ADP5034RE-EVALZ
Evaluation Board for ADP5034ACPZ-R7
Evaluation Board for ADP5034AREZ-R7
1 Z = RoHS Compliant Part.
2 For additional options, contact a local sales or distribution representative. Additional options available are:
BUCK1 and BUCK2: 3.3 V, 3.0 V, 2.8 V, 2.5 V, 2.3 V, 2.0 V, 1.8 V, 1.6 V, 1.5 V, 1.4 V, 1.3 V, 1.2 V, 1.1 V, 1.0 V, 0.9 V, or adjustable.
LDO1 and LDO2: 3.3 V, 3.0 V, 2.8 V, 2.5 V, 2.25 V, 2.0 V, 1.8 V, 1.7 V, 1.6 V, 1.5 V, 1.2 V, 1.1 V, 1.0 V, 0.9 V, 0.8 V, or adjustable.
3 UVLO: low or high.
4 BUCK1, BUCK2, both LDO1 and LDO2: Active pull-down resistor is programmable to be either enabled or disabled.
©2011–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09703-0-5/13(E)
Rev. E | Page 28 of 28
相关型号:
ADP5041ACPZ-1-R7
Micro PMU with 1.2 A Buck, Two 300 mA LDOs, Supervisory, Watchdog, and Manual Reset
ADI
ADP5041CP-1-EVALZ
Micro PMU with 1.2 A Buck, Two 300 mA LDOs, Supervisory, Watchdog, and Manual Reset
ADI
©2020 ICPDF网 联系我们和版权申明