ADM6711RAKSZ-REEL-7 [ADI]
IC 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4, LEAD FREE, EIAJ SC82, SC-70, 4 PIN, Power Management Circuit;型号: | ADM6711RAKSZ-REEL-7 |
厂家: | ADI |
描述: | IC 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4, LEAD FREE, EIAJ SC82, SC-70, 4 PIN, Power Management Circuit 光电二极管 |
文件: | 总12页 (文件大小:279K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Microprocessor Supervisory
Circuit in 4-Lead SC70
ADM6711/ADM6713
FUNCTIONAL BLOCK DIAGRAMS
FEATURES
Specified over temperature
Low power consumption (12 μA)
Precision monitoring of 2.5 V, 3 V, 3.3 V,
and 5 V power supply voltages
Reset timeout period of 140 ms (minimum)
Manual reset input
ADM6711
V
RESET
CC
GENERATOR
240ms
RESET
GND
V
REF
MR
DEBOUNCE
Output stages
Push-pull RESET output (ADM6711)
Open-drain RESET output (ADM6713)
Reset assertion down to 1 V VCC
Power supply glitch immunity
4-lead SC70 package
Figure 1.
ADM6713
V
CC
RESET
GENERATOR
240ms
RESET
GND
V
REF
APPLICATIONS
Microprocessor systems
Computers
MR
DEBOUNCE
Controllers
Intelligent instruments
Automotive systems
Figure 2.
GENERAL DESCRIPTION
The ADM6711/ADM6713 are reset generator circuits suitable
for use in microprocessor-based systems. They provide a reset
signal on power-up, power-down, and whenever the supply
voltage falls below a preset threshold. In addition, both parts
have a debounced manual reset input so that a reset signal can
also be initiated with an external switch or logic signal.
The parts are highly reliable with accurate voltage references
and immunity to fast, negative-going transients on VCC. Low
current consumption and space-efficient, 4-lead SC70
packaging make the ADM6711/ADM6713 ideal for use in low
power portable applications.
With six different reset threshold options available ranging
from 2.32 V to 4.63 V, the ADM6711/ADM6713 are suitable for
monitoring 2.5 V, 3 V, 3.3 V, and 5 V supplies. A reset timeout
of at least 140 ms occurs when VCC rises above the threshold.
This gives the supply voltage time to stabilize before the
microprocessor starts up.
V
V
CC
*R
PULL-UP
CC
MICROPROCESSOR
SYSTEM
ADM6711/
ADM6713
MR
RESET
RESET
GND
GND
The ADM6711 has a push-pull output, so no additional
external components are needed. The ADM6713 open-drain
output requires an external pull-up resistor that can be
connected to a voltage higher than VCC, if desired.
*ADM6713 ONLY
Figure 3. Typical Operating Circuit
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2006 Analog Devices, Inc. All rights reserved.
ADM6711/ADM6713
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ..............................................7
Circuit Description............................................................................8
Manual Reset Input.......................................................................8
Power Supply Glitch Immunity...................................................8
Applications....................................................................................... 1
Functional Block Diagrams............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
ADM6713
Output Logic Levels .....................................8
RESET
Ensuring a Valid
Output Down To VCC = 0 V ............8
RESET
Outline Dimensions..........................................................................9
Ordering Guide .............................................................................9
REVISION HISTORY
12/06—Rev. 0 to Rev. A
Updated Format..................................................................Universal
Changes to Specifications Table...................................................... 3
Changes to Figure 10........................................................................ 8
Changes to Ordering Guide ............................................................ 9
8/03—Revision 0: Initial Version
Rev. A | Page 2 of 12
ADM6711/ADM6713
SPECIFICATIONS
VCC = full operating range; TA = TMIN to TMAX; VCC typ = 5 V for L/M models, 3.3 V for T/S models, 3 V for R models, and 2.5 V for Z models,
unless otherwise noted.
Table 1.
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
SUPPLY
VCC Operating Voltage Range
1.0
1.2
5.5
5.5
35
V
V
μA
TA = 0°C to 70°C
TA = −40°C to +125°C
VCC < 5.5 V, ADM671_L/M,
TA = −40°C to +85°C
VCC < 3.6 V, ADM671_R/S/T/Z,
TA = −40°C to +85°C
VCC < 5.5 V, ADM671_L/M,
TA = 85°C to 125°C
VCC < 3.6 V, ADM671_R/S/T/Z,
TA = 85°C to 125°C
Supply Current
16
12
30
60
60
μA
μA
μA
RESET VOLTAGE THRESHOLD
ADM671_L
4.56
4.50
4.44
4.31
4.25
4.20
3.04
3.00
2.95
2.89
2.85
2.81
2.59
2.55
2.52
2.28
2.25
2.22
4.63
4.38
3.08
2.93
2.63
2.32
30
4.70
4.75
4.82
4.45
4.50
4.56
3.11
3.15
3.21
2.96
3.00
3.05
2.66
2.70
2.74
2.35
2.38
2.42
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
TA = 25°C
TA = −40°C to +85°C
TA = 85°C to 125°C
TA = 25°C
TA = −40°C to +85°C
TA = 85°C to 125°C
TA = 25°C
TA = −40°C to +85°C
TA = 85°C to 125°C
TA = 25°C
TA = −40°C to +85°C
TA = 85°C to 125°C
TA = 25°C
TA = −40°C to +85°C
TA = 85°C to 125°C
TA = 25°C
TA = −40°C to +85°C
TA = 85°C to 125°C
ADM671_M
ADM671_T
ADM671_S
ADM671_R
ADM671_Z
V
V
RESET THRESHOLD TEMPERATURE
COEFFICIENT
ppm/°C
VCC to RESET DELAY
20
μs
VCC = VTH to (VTH − 100 mV)
RESET ACTIVE TIMEOUT PERIOD
140
100
240
460
640
ms
ms
TA = −40°C to +85°C
TA = 85°C to 125°C
RESET OUTPUT VOLTAGE
Low (ADM6711/ADM6713)
0.3
0.4
0.3
V
V
VCC = VTH min, ISINK = 1.2 mA,
ADM671_R/S/T/Z
VCC = VTH min, ISINK = 3.2 mA,
ADM671_L/M
VCC >1.0 V, ISINK = 50 μA
VCC > VTH max, ISOURCE = 500 μA,
ADM6711R/S/T/Z
VCC > VTH max, ISOURCE = 800 μA,
ADM6711L/M
V
V
High (ADM6711)
0.8 VCC
0.8 VCC
V
Rev. A | Page 3 of 12
ADM6711/ADM6713
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
RESET OPEN-DRAIN OUTPUT
LEAKAGE CURRENT
MANUAL RESET (MR)
Input Threshold
1
ꢀA
VCC > VTH, RESET deasserted
0.3 VCC
V
VIL
0.7 VCC
V
VIH
Pull-Up Resistance
Minimum Pulse width
Glitch Immunity
Reset Delay
10
1
20
kΩ
ꢀs
ns
ns
100
200
Rev. A | Page 4 of 12
ADM6711/ADM6713
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 3.
Threshold Options
RESET
Model
RESET Threshold (V)
Table 2.
ADM671_L
ADM671_M
ADM671_T
ADM671_S
ADM671_R
ADM671_Z
4.63
4.38
3.08
2.93
2.63
2.32
Parameter
VCC
RESET (Push-Pull)
RESET (Open-Drain)
MR
Rating
−0.3 V to +6 V
−0.3 V to (VCC + 0.3 V)
−0.3 V to +6 V
−0.3 V to (VCC + 0.3 V)
Input Current
VCC, MR
20 mA
Output Current
RESET
ESD CAUTION
20 mA
Rate of Rise, VCC
θJA Thermal Impedance, SC70
Operating Temperature Range
Storage Temperature Range
Lead Temperature (Soldering, 10 sec)
100 V/ꢀs
146°C/W
−40°C to +125°C
−65°C to +150°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. A | Page 5 of 12
ADM6711/ADM6713
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
GND
1
ADM6711/
ADM6713
TOP VIEW
4
V
CC
(Not to Scale)
2
3
RESET
MR
Figure 4. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic
Description
1
2
GND
RESET
Ground Reference for All Signals (0 V).
Active Low Logic Input. RESET remains low while VCC is below the reset threshold and remains low for
240 ms (typical) after VCC rises above the reset threshold.
3
4
MR
VCC
Manual Reset. This active low debounced input ignores input pulses of 100 ns (typical) and is guaranteed
to accept input pulses greater than 1 ꢀs. Leave floating when not used.
Supply Voltage Being Monitored.
Rev. A | Page 6 of 12
ADM6711/ADM6713
TYPICAL PERFORMANCE CHARACTERISTICS
12
1.007
1.006
1.005
1.004
1.003
1.002
1.001
1.000
0.999
0.998
0.997
0.996
0.995
I
@ V = 5.5V
CC
DD
10
8
6
I
@ V = 3V
DD
CC
4
2
0
I
@ V = 1V
DD CC
–40
–20
0
20
30
50
70
85
100
120
–40
–20
0
20
30
50
70
85
100
120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 5. Supply Current vs. Temperature
RESET
Figure 8.
Threshold Deviation vs. Temperature
1000
400
900
800
700
600
500
400
300
200
350
300
250
200
150
100
50
ADM671_L/M
V
= 20mV
OD
ADM671_R/S/T/Z
V
V
= 125mV
= 200mV
OD
OD
100
0
0
–40
–20
0
20
30
50
70
85
100
120
0
10
100
1000
TEMPERATURE (°C)
RESET COMPARATOR OVERDRIVE, V – V (mV)
TH
CC
RESET
Figure 6. Power-Down
Delay vs. Temperature: ADM671_R/S/T/Z
RESET
Figure 9. Maximum Transient Duration (Without Causing a
RESET
Pulse) vs.
Comparator Overdrive
900
800
700
600
500
400
300
200
V
= 20mV
OD
V
= 125mV
OD
100
0
V
= 200mV
OD
–20
–40
0
20
30
50
70
85
100
120
TEMPERATURE (°C)
RESET
Figure 7. Power-Down
Delay vs. Temperature: ADM671_L/M
Rev. A | Page 7 of 12
ADM6711/ADM6713
CIRCUIT DESCRIPTION
ADM6713
OUTPUT LOGIC LEVELS
RESET
The ADM6711/ADM6713 are designed to protect the integrity
of a system’s operation by ensuring the proper operation of the
system during power-up, power-down, and brownout conditions.
The ADM6713 open-drain
output is designed for use
RESET
with an external pull-up resistor. This resistor can be tied to VCC
or any other reasonable voltage level, offering the flexibility
to use the ADM6713 to drive a variety of different logic level
circuitry.
When the ADM6711/ADM6713 are powered up, the
RESET
output remains low for a period equal to the typical reset active
timeout period. This is designed to give the system time to
power up correctly and for the power supply to stabilize before
any devices are brought out of reset and allowed to begin
executing instructions. Initializing a system in this way provides
a more reliable startup for microprocessor systems.
ENSURING A VALID
VCC = 0 V
OUTPUT DOWN TO
RESET
When VCC falls below 0.8 V, the ADM6711/ADM6713
RESET
output no longer sinks current, and a high impedance CMOS
logic input connected to may drift to undetermined
MANUAL RESET INPUT
RESET
logic levels. To eliminate this problem, a pull-down resistor is
connected from to ground. A 100 kΩ resistor is large enough
The ADM6711/ADM6713 manual reset (
system operator to reset a system by means of an external
manual switch. Alternatively, a logic signal from another digital
circuit can be used to trigger a reset via the
) input allows the
MR
RESET
and small enough to pull
not to load
to ground.
RESET
RESET
input.
MR
V
CC
The
input ignores negative-going pulses faster than 100 ns
MR
(typical) and is guaranteed to accept any negative-going input
pulse of a duration greater than or equal to 1 μs. The
V
CC
RESET
is held low and for 240 ms
ADM6711
RESET
output remains low while
MR
100kΩ
(typical) after
returns high.
MR
GND
If
is connected to long cables or is used in a noisy environ-
MR
ment, then placing a 0.1 μF capacitor between the
and ground helps to remove any fast, negative-going transients.
input
MR
ADM6711
V
RESET
GENERATOR
240ms
CC
POWER SUPPLY GLITCH IMMUNITY
RESET
V
REF
The ADM6711/ADM6713 contain internal filtering circuitry
that provides immunity to fast transient glitches on the power
supply line. Figure 9 illustrates glitch immunity performance by
showing the maximum transient duration without causing a reset
pulse for glitches with amplitudes in the range of 1 mV to 1000 mV.
MR
GND
DEBOUNCE
RESET
Figure 10. Ensuring a Valid
Output Down to VCC = 0 V
Glitch immunity makes the ADM6711/ADM6713 suitable for
use in noisy environments. Mounting a 0.1 μF decoupling
capacitor as close as possible to the VCC pin improves glitch
immunity further.
Rev. A | Page 8 of 12
ADM6711/ADM6713
OUTLINE DIMENSIONS
2.20
1.80
1.35
1.15
3
4
1
2.40
1.80
2
PIN 1
0.65 BSC
0.50 BSC
12°
8°
0.40
0.10
1.00
0.80
1.10
0.80
0.30
0.10
SEATING
PLANE
0.18
0.10
0.10 MAX
*
0.70
0.50
0.30
0.15
0.10 COPLANARITY
*
PACKAGE OUTLINE CORRESPONDS IN FULL TO EIAJ SC82
EXCEPT FOR WIDTH OF PIN 2 AS SHOWN.
Figure 11. 4-Lead Thin Shrink Small Outline Transistor Package [SC70]
(EIAJ SC82 body)
(KS-4)
Dimensions shown in millimeters
ORDERING GUIDE
RESET
Temperature
Range
Package
Description
Package
Option
Ordering
Quantity (k)
10
10
3
3
10
3
Model
Threshold (V)
Branding
M0B
M4U
M0B
M4U
M0C
M0C
M86
M0D
M4A
M0D
M4A
M0E
M4B
M0E
M4B
M0F
M5F
M0F
M5F
M0G
M4H
M0G
M4H
M0H
M87
M0H
M87
M0J
ADM6711LAKS-REEL
ADM6711LAKSZ-REEL1
ADM6711LAKS-REEL-7
ADM6711LAKSZ-REEL-71
ADM6711MAKS-REEL
ADM6711MAKS-REEL-7
ADM6711MAKSZ-REEL-71
ADM6711TAKS-REEL
ADM6711TAKSZ-REEL1
ADM6711TAKS-REEL-7
ADM6711TAKSZ-REEL-71
ADM6711SAKS-REEL
ADM6711SAKSZ-REEL1
ADM6711SAKS-REEL-7
ADM6711SAKSZ-REEL-71
ADM6711RAKS-REEL
ADM6711RAKSZ-REEL1
ADM6711RAKS-REEL-7
ADM6711RAKSZ-REEL-71
ADM6711ZAKS-REEL
ADM6711ZAKSZ-REEL1
ADM6711ZAKS-REEL-7
ADM6711ZAKSZ-REEL-71
ADM6713LAKS-REEL
ADM6713LAKSZ-REEL1
ADM6713LAKS-REEL-7
ADM6713LAKSZ-REEL-71
ADM6713MAKS-REEL
ADM6713MAKS-REEL-7
ADM6713MAKSZ-REEL-71
ADM6713TAKS-REEL
4.63
4.63
4.63
4.63
4.38
4.38
4.38
3.08
3.08
3.08
3.08
2.93
2.93
2.93
2.93
2.63
2.63
2.63
2.63
2.32
2.32
2.32
2.32
4.63
4.63
4.63
4.63
4.38
4.38
4.38
3.08
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
3
10
10
3
3
10
10
3
3
10
10
3
3
10
10
3
3
10
10
3
3
10
3
M0J
M88
M0K
3
10
Rev. A | Page 9 of 12
ADM6711/ADM6713
RESET
Threshold (V)
Temperature
Range
Package
Description
Package
Option
Ordering
Quantity (k)
Model
Branding
M0K
M89
M0L
M57
M0L
M57
M0M
M4S
M0M
M4S
ADM6713TAKS-REEL-7
ADM6713TAKSZ-REEL-71
ADM6713SAKS-REEL
ADM6713SAKSZ-REEL1
ADM6713SAKS-REEL-7
ADM6713SAKSZ-REEL-71
ADM6713RAKS-REEL
ADM6713RAKSZ-REEL1
ADM6713RAKS-REEL-7
ADM6713RAKSZ-REEL-71
ADM6713ZAKS-REEL
ADM6713ZAKSZ-REEL1
ADM6713ZAKS-REEL-7
ADM6713ZAKSZ-REEL-71
3.08
3.08
2.93
2.93
2.93
2.93
2.63
2.63
2.63
2.63
2.32
2.32
2.32
2.32
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
4-Lead SC70
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
KS-4
3
3
10
10
3
3
10
10
3
3
10
10
3
M0N
M4R
M0N
M4R
3
1 Z = Pb-free part.
Rev. A | Page 10 of 12
ADM6711/ADM6713
NOTES
Rev. A | Page 11 of 12
ADM6711/ADM6713
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C03754-0-12/06(A)
Rev. A | Page 12 of 12
相关型号:
ADM6711SAKSZ-REEL-7
IC 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4, LEAD FREE, EIAJ SC82, SC-70, 4 PIN, Power Management Circuit
ADI
©2020 ICPDF网 联系我们和版权申明