ADA4817-1 [ADI]
Low Noise, 1 GHz FastFET Op Amps; 低噪声, 1 GHz的FastFET运算放大器型号: | ADA4817-1 |
厂家: | ADI |
描述: | Low Noise, 1 GHz FastFET Op Amps |
文件: | 总24页 (文件大小:519K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Low Noise, 1 GHz
FastFET Op Amps
ADA4817-1/ADA4817-2
CONNECTION DIAGRAMS
FEATURES
ADA4817-1
High speed
TOP VIEW
(Not to Scale)
−3 dB bandwidth (G = 1, RL = 100 Ω): 1050 MHz
Slew rate: 870 V/μs
0.1% settling time: 9 ns
Low input bias current: 2 pA
Low input capacitance
PD
FB
1
2
3
4
8
7
6
5
+V
S
OUT
NC
–IN
+IN
–V
S
Common-mode capacitance: 1.5 pF
Differential-mode capacitance: 0.1 pF
Low noise
NC = NO CONNECT
Figure 1. 8-Lead ADA4817-1 LFCSP (CP-8-2)
4 nV/√Hz @ 100 kHz
2.5 fA/√Hz @ 100 kHz
Low distortion
ADA4817-2
TOP VIEW
(Not to Scale)
−90 dBc @ 10 MHz (G = 1, RL = 1 kΩ)
Offset voltage: 2 mV maximum
High output current: 70 mA
Supply current per amplifier: 19 mA
Power-down supply current per amplifier: 1 mA
12 –V
–IN1 1
+IN1 2
NC 3
S1
11 NC
10 +IN2
APPLICATIONS
–V
4
9 –IN2
S2
Photodiode amplifiers
Data acquisition front ends
Instrumentation
Filters
NC = NO CONNECT
Figure 2. 16-Lead ADA4817-2 LFSCP (CP-16-4)
ADC drivers
CCD output buffers
GENERAL DESCRIPTION
The ADA4817-1 (single) and ADA4817-2 (dual) FastFET™
amplifiers are unity-gain stable, ultrahigh speed voltage
feedback amplifiers with FET inputs. These amplifiers are
developed in the Analog Devices, Inc., proprietary eXtra Fast
Complementary Bipolar (XFCB) process, which allows the
amplifiers to achieve ultralow noise (4 nV/√Hz; 2.5 fA/√Hz)
as well as very high input impedances.
With a wide supply voltage range from 5 V to 10 V, the ability
to operate on either single or dual supplies, the ADA4817-1/
ADA4817-2 are designed to work in a variety of applications
including active filtering and ADC driving.
The ADA4817-1 is available in a 3 mm × 3 mm 8-lead LFCSP
and the ADA4817-2 is available in a 4 mm × 4 mm 16-lead LFSCP.
Both packages feature a low distortion pinout, which improves
second harmonic distortion and simplifies the layout of the
circuit board. In addition, both packages feature an exposed
paddle that provides a low thermal resistance path to the
printed circuit board (PCB). This enables more efficient heat
transfer and increases reliability. Both products are rated to
work over the extended industrial temperature range (−40°C
to +105°C).
With 1.5 pF of input capacitance, low noise (4 nV/√Hz),
low offset voltage (2 mV maximum), and 1050 MHz −3 dB
bandwidth, the ADA4817-1/ADA4871-2 are ideal for data
acquisition front ends as well as wideband transimpedance
applications, such as photodiode preamps.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2008 Analog Devices, Inc. All rights reserved.
ADA4817-1/ADA4817-2
TABLE OF CONTENTS
Features .............................................................................................. 1
Driving Capacitive Loads.......................................................... 14
Thermal Considerations............................................................ 14
Power-Down ꢀperation............................................................ 15
Capacitive Feedback................................................................... 15
Layout, Grounding, and Bypassing Considerations .................. 16
Signal Routing............................................................................. 16
Power Supply Bypassing............................................................ 16
Grounding................................................................................... 16
Exposed Paddle........................................................................... 16
Leakage Currents........................................................................ 17
Input Capacitance ...................................................................... 17
Input-to-Input/ꢀutput Coupling............................................. 17
Applications Information.............................................................. 18
Low Distortion Pinout............................................................... 18
Wideband Photodiode Preamp................................................ 18
High Speed JFET Input Instrumentation Amplifier.............. 20
Active Low-Pass Filter (LPF) .................................................... 21
ꢀutline Dimensions....................................................................... 23
ꢀrdering Guide .......................................................................... 23
Applications....................................................................................... 1
Connection Diagrams...................................................................... 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
5 V ꢀperation............................................................................. 3
5 V ꢀperation ............................................................................... 4
Absolute Maximum Ratings............................................................ 5
Thermal Resistance ...................................................................... 5
Maximum Safe Power Dissipation............................................. 5
ESD Caution.................................................................................. 5
Pin Configurations and Function Descriptions ........................... 6
Typical Performance Characteristics ............................................. 7
Test Circuits..................................................................................... 12
Theory of ꢀperation ...................................................................... 13
Closed-Loop Frequency Response........................................... 13
Noninverting Closed-Loop Frequency Response.................. 13
Inverting Closed-Loop Frequency Response............................. 13
Wideband ꢀperation ................................................................. 14
REVISION HISTORY
11/08—Revision 0: Initial Version
Rev. 0 | Page 2 of 24
ADA4817-1/ADA4817-2
SPECIFICATIONS
5 V OPERATION
TA = 25°C, G = 1, RF = 348 Ω for G > 1, RL = 100 Ω to ground, unless otherwise noted.
Table 1.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
–3 dB Bandwidth
VOUT = 0.1 V p-p
VOUT = 2 V p-p
VOUT = 0.1 V p-p, G = 2
VOUT = 0.1 V p-p
VOUT = 2 V p-p, RL = 100 Ω, G = 2
VOUT = 4 V step
1050
200
390
≥410
60
MHz
MHz
MHz
MHz
MHz
V/μs
ns
Gain Bandwidth Product
0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
Harmonic Distortion (HD2/HD3)
870
9
VOUT = 2 V step, G = 2
f = 1 MHz, VOUT = 2 V p-p, RL = 1 kΩ
f = 10 MHz, VOUT = 2 V p-p, RL = 1 kΩ
f = 50 MHz, VOUT = 2 V p-p, RL = 1 kΩ
f = 100 kHz
−113/−117
−90/−94
−64/−66
4
dBc
dBc
dBc
nV/√Hz
fA/√Hz
Input Voltage Noise
Input Current Noise
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
f = 100 kHz
2.5
0.4
7
2
2
mV
μV/°C
pA
20
TMIN to TMAX
100
1
pA
pA
Input Bias Offset Current
Open-Loop Gain
62
65
dB
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Common-mode
Common-mode
Differential-mode
500
1.5
0.1
−5 to +2.3
−90
GΩ
pF
pF
V
Input Common-Mode Voltage Range
Common-Mode Rejection
VCM = 0.5 V
−77
dB
OUTPUT CHARACTERISTICS
Output Overdrive Recovery Time
Output Voltage Swing
VIN = 2.5 V, G = 2
RL = 1 kΩ
8
ns
V
V
mA
mA
−3.5 to +3.5
−3.9 to +3.9
−3.6 to +3.7
−4.0 to +4.0
70
Linear Output Current
Short-Circuit Current
POWER-DOWN
Sinking/sourcing
100/170
PD Pin Voltage
Enabled
>+VS − 1
<+VS − 3
0.3/1
V
Powered down
V
Turn-On/Turn-Off Time
Input Leakage Current
μs
μA
μA
PD = +VS
PD = −VS
0.3
3
34
55
POWER SUPPLY
Operating Range
5
10
21
3
V
Quiescent Current per Amplifier
Powered Down Quiescent Current
Positive Power Supply Rejection
Negative Power Supply Rejection
19
1.5
−72
−72
mA
mA
dB
dB
+VS = 4.5 V to 5.5 V, −VS = −5 V
+VS = 5 V, −VS = −4.5 V to −5.5 V
−67
−67
Rev. 0 | Page 3 of 24
ADA4817-1/ADA4817-2
5 V OPERATION
TA = 25°C, +VS = 3 V, −VS = −2 V, G = 1, RF = 348 Ω for G > 1, RL = 100 Ω to midsupply, unless otherwise noted.
Table 2.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
–3 dB Bandwidth
VOUT = 0.1 V p-p
VOUT = 1 V p-p
VOUT = 0.1 V p- p, G = 2
VOUT = 1 V p-p, G = 2
VOUT = 2 V step
500
160
280
32
320
11
MHz
MHz
MHz
MHz
V/μs
ns
0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
Harmonic Distortion (HD2/HD3)
VOUT = 1 V step, G = 2
f = 1 MHz, VOUT = 1 V p-p, RL = 1 kΩ
f = 10 MHz, VOUT = 1 V p-p, RL = 1 kΩ
f = 50 MHz, VOUT = 1 V p-p, RL = 1 kΩ
f = 100 kHz
−87/−88
−68/−66
−57/−55
4
dBc
dBc
dBc
nV/√Hz
fA/√Hz
Input Voltage Noise
Input Current Noise
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
f = 100 kHz
2.5
0.5
7
2
2.3
20
mV
μV/°C
pA
TMIN to TMAX
100
1
pA
pA
Input Bias Offset Current
Open-Loop Gain
61
63
dB
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Common-mode
Common-mode
Differential-mode
500
1.3
0.1
0 to 2.3
−83
GΩ
pF
pF
V
Input Common-Mode Voltage Range
Common-Mode Rejection
VCM = 0.25 V
VIN = 1.25 V, G = 2
RL = 1 kΩ
−72
dB
OUTPUT CHARACTERISTICS
Output Overdrive Recovery Time
Output Voltage Swing
13
ns
V
V
mA
mA
1.3 to 3.7
1 to 3.9
1 to 3.8
0.9 to 4.0
55
Linear Output Current
Short-Circuit Current
POWER-DOWN
Sinking/sourcing
40/130
PD Pin Voltage
Enabled
>+VS − 1
<+VS − 3
0.2/0.7
0.2
V
Powered Down
V
Turn-On/Turn-Off Time
Input Leakage Current
μs
μA
μA
PD = +VS
PD = −VS
3
31
45
POWER SUPPLY
Operating Range
5
10
15
2.5
V
Quiescent Current per Amplifier
Powered Down Quiescent Current
Positive Power Supply Rejection
Negative Power Supply Rejection
14
1.5
−71
−69
mA
mA
dB
dB
+VS = 4.75 V to 5.25 V, −VS = 0 V
+VS = 5 V, −VS = −0.25 V to +0.25 V
−66
−63
Rev. 0 | Page 4 of 24
ADA4817-1/ADA4817-2
ABSOLUTE MAXIMUM RATINGS
PD = Quiescent Power + (Total Drive Power – Load Power) (1)
Table 3.
2
Parameter
Rating
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
VS VOUT
VOUT
RL
PD =
(
VS × IS
)
+
×
–
(2)
Supply Voltage
10.6 V
2
RL
Power Dissipation
See Figure 3
−VS − 0.5 V to +VS + 0.5 V
±VS
−65°C to +125°C
−40°C to +105°C
300°C
RMS output voltages should be considered. If RL is referenced
to −VS, as in single-supply operation, the total drive power is
VS × IꢀUT. If the rms signal levels are indeterminate, consider the
Common-Mode Input Voltage
Differential Input Voltage
Storage Temperature Range
Operating Temperature Range
Lead Temperature
(Soldering, 10 sec)
worst-case scenario, when VOUT = VS/4 for RL to midsupply.
2
VS /4
RL
)
PD =
(
VS × IS
)
+
(3)
Junction Temperature
150°C
In single-supply operation with RL referenced to −VS, worst-
case situation is VOUT = VS/2.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Airflow increases heat dissipation, effectively reducing θJA.
More metal directly in contact with the package leads and
exposed paddle from metal traces, throughholes, ground,
and power planes also reduces θJA.
Figure 3 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the exposed paddle
LFCSP_VD (single 94°C/W) and LFCSP_VQ (dual 64°C/W)
package on a JEDEC standard 4-layer board. θJA values are
approximations.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, θJA is
specified for a device soldered in circuit board for surface-
mount packages.
3.5
3.0
Table 4.
ADA4817-2
Package Type
θJA
94
64
θJC
29
14
Unit
°C/W
°C/W
2.5
2.0
LFCSP_VD (ADA4817-1)
LFSCP_VQ (ADA4817-2)
1.5
MAXIMUM SAFE POWER DISSIPATION
ADA4817-1
The maximum safe power dissipation for the ADA4817-1/
ADA4817-2 are limited by the associated rise in junction
temperature (TJ) on the die. At approximately 150°C (which is
the glass transition temperature), the properties of the plastic
change. Even temporarily exceeding this temperature limit may
change the stresses that the package exerts on the die,
permanently shifting the parametric performance of the
ADA4817. Exceeding a junction temperature of 175°C for an
extended period can result in changes in silicon devices,
potentially causing degradation or loss of functionality.
1.0
0.5
0
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80 90 100
AMBIENT TEMPERATURE (°C)
Figure 3. Maximum Safe Power Dissipation vs. Ambient Temperature for a
4-Layer Board
ESD CAUTION
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the die
due to the ADA4817-1/ADA4817-2 drive at the output. The
quiescent power is the voltage between the supply pins (VS)
multiplied by the quiescent current (IS).
Rev. 0 | Page 5 of 24
ADA4817-1/ADA4817-2
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
ADA4817-2
TOP VIEW
(Not to Scale)
ADA4817-1
TOP VIEW
(Not to Scale)
12 –V
–IN1 1
+IN1 2
NC 3
S1
11 NC
10 +IN2
PD
FB
1
2
3
4
8
7
6
5
+V
S
–V
4
9 –IN2
S2
OUT
NC
–IN
+IN
–V
S
NC = NO CONNECT
NC = NO CONNECT
NOTES
NOTES
1. EXPOSED PAD CAN BE CONNECTED
TO GROUND PLANE OR NEGATIVE
SUPPLY PLANE.
1. EXPOSED PAD CAN BE CONNECTED
TO THE GROUND PLANE OR NEGATIVE
SUPPLY PLANE.
Figure 4. 8-Lead LFCSP Pin Configuration
Figure 5. 16-Lead LFCSP Pin Configuration
Table 5. 8-Lead LFCSP Pin Function Descriptions
Table 6. 16-Lead LFCSP Pin Function Descriptions
Pin No. Mnemonic
Description
Pin No.
Mnemonic
−IN1
+IN1
NC
Description
1
2
3
4
5
6
7
8
PD
Power-Down. Do not leave floating.
Feedback Pin.
1
Inverting Input 1.
2
Noninverting Input 1.
No Connect.
FB
3, 11
4
−IN
+IN
−VS
NC
Inverting Input.
−VS2
Negative Supply 2.
Output 2.
Noninverting Input.
Negative Supply.
No Connect.
5
OUT2
+VS2
6
Positive Supply 2.
7
PD2
Power-Down 2. Do not leave floating.
Feedback Pin 2.
OUT
+VS
Output.
8
FB2
Positive Supply.
9
−IN2
+IN2
−VS1
Inverting Input 2.
9 (EPAD) Exposed
Exposed Pad. Can be connected to
paddle (EPAD) GND, −VS plane or left floating.
10
12
13
14
15
16
Noninverting Input 2.
Negative Supply 1.
Output 1.
OUT1
+VS1
Positive Supply 1.
PD1
Power-Down 1. Do not leave floating.
Feedback Pin 1.
FB1
17 (EPAD) Exposed
Exposed Pad. Can be connected to
paddle (EPAD) GND, −VS plane or left floating.
Rev. 0 | Page 6 of 24
ADA4817-1/ADA4817-2
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VS = 5 V, G = 1, (RF = 348 Ω for G > 1), RL = 100 Ω to ground, small signal VꢀUT = 100 mV p-p, large signal VꢀUT = 2 V p-p,
unless noted otherwise.
6
3
G = 1, DUAL
G = 2
G = 1, SINGLE
G = 2
3
0
0
G = 1, DUAL
G = 1, SINGLE
G = 5
–3
–6
–9
–12
G = 5
–3
–6
–9
–12
100k
1M
10M
100M
1G
10G
100k
1M
10M
100M
1G
10G
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 6. Small Signal Frequency Response for Various Gains
Figure 9. Large Signal Frequency Response for Various Gains
6
3
0
6
3
V
V
= 10V
S
= 2V p-p
OUT
0
–3
V
= 10V
S
–3
–6
V
= 5V
V
= 5V
S
S
V
= 1V p-p
OUT
–6
–9
–9
–12
100k
–12
100k
1M
10M
100M
1G
1G
1M
10M
100M
1G
10G
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 10. Large Signal Frequency Response for Various Supplies
Figure 7. Small Signal Frequency Response for Various Supplies
9
9
C
= 6.6pF
L
R
= 274Ω
F
C
= 2.2pF
L
R = 348Ω
F
C
= 4.4pF
L
6
3
6
3
C
= 0pF
L
R
= 200Ω
F
0
0
–3
–6
–9
–3
–6
–9
G = 2
= 274Ω
G = 2
R
F
100k
1M
10M
100M
1G
10G
100k
1M
10M
100M
1G
10G
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 11. Small Signal Frequency Response for Various RF
Figure 8. Small Signal Frequency Response for Various CL
Rev. 0 | Page 7 of 24
ADA4817-1/ADA4817-2
0.5
6
3
0.4
G = 2, SS
0.3
G = 2, LS
0.2
0
0.1
0
G = 1, SS
G = 1, LS
–3
–6
–9
–12
–0.1
–0.2
–0.3
–0.4
–0.5
T
T
T
T
T
T
= +25°C, SINGLE
= +25°C, DUAL
= –40°C, SINGLE
= –40°C, DUAL
= +105°C, SINGLE
= +105°C, DUAL
A
A
A
A
A
A
100k
1M
10M
100M
1G
10G
100k
1M
10M
100M
1G
10G
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 12. 0.1 dB Flatness Frequency Response vs. Gain and Output Voltage
Figure 15. Small Signal Frequency Response vs. Temperature
–20
–40
–60
–20
–40
–60
HD2, V = 5V
S
HD2, R = 100Ω
L
HD3, V = 5V
S
–80
–100
–120
–140
–80
–100
–120
–140
HD2, R = 1kΩ
L
HD3, R = 100Ω
L
HD2, V = 10V
S
HD3, R = 1kΩ
HD3, V = 10V
L
S
100k
1M
10M
FREQUENCY (Hz)
100M
100k
1M
10M
FREQUENCY (Hz)
100M
Figure 13. Distortion vs. Frequency for Various Loads, VOUT = 2 V p-p
Figure 16. Distortion vs. Frequency for Various Supplies, VOUT = 2 V p-p
–20
–40
–20
fC = 1MHz
–40
–60
–80
HD2, V = 5V
S
–60
–80
HD2, V = 10V
S
HD2, R = 100Ω
L
HD2, R = 1kΩ
L
–100
–120
–140
–100
–120
–140
HD3, V = 5V
S
HD3, V = 10V
S
HD3, R = 100Ω
L
HD3, R = 1kΩ
L
100k
1M
10M
FREQUENCY (Hz)
100M
0
1
2
3
4
5
6
OUTPUT VOLTAGE (V p-p)
Figure 14. Distortion vs. Frequency for Various Supplies, G = 2, VOUT = 2 V p-p
Figure 17. Distortion vs. Output Voltage for Various Loads
Rev. 0 | Page 8 of 24
ADA4817-1/ADA4817-2
0.15
0.10
0.05
0
0.15
0.10
0.05
0
DUAL, C = 0.5pF
F
DUAL, C = 0.5pF
F
SINGLE, NO C
F
SINGLE, NO C
F
SINGLE
SINGLE
–0.05
–0.10
–0.15
–0.05
–0.10
–0.15
DUAL
DUAL
V
G = 2
= 5V
S
G = 2
TIME (5ns/DIV)
TIME (5ns/DIV)
Figure 18. Small Signal Transient Response
Figure 21. Small Signal Transient Response
1.5
1.0
6
G = 2
4
2
0.5
V
OUT
0
0
–0.5
–1.0
–1.5
DUAL
–2
–4
–6
DUAL, C = 0.5pF
F
SINGLE, NO C
F
SINGLE
G = 2
2 × V
IN
TIME (5ns/DIV)
TIME (100 ns/DIV)
Figure 19. Output Overdrive Recovery
Figure 22. Large Signal Transient Response
0.5
0.4
0.3
N: 4197
SETTLING TIME
MEAN: –0.0248457
800
700
600
500
400
300
200
100
0
SD: 0.245658
0.2
0.1
0
–0.1
–0.2
–0.3
–0.4
–0.5
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
V
(mV)
OS
TIME (5ns/DIV)
Figure 23. 0.1% Short-Term Settling Time
Figure 20. Input Offset Voltage Histogram
Rev. 0 | Page 9 of 24
ADA4817-1/ADA4817-2
0
–10
–20
–30
0.5
0.4
0.3
0.2
–40
0.1
–PSRR
+PSRR
–50
–60
0
–0.1
–0.2
–0.3
–0.4
–0.5
–70
–80
–90
–100
100k
1M
10M
FREQUENCY (Hz)
100M
1G
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 24. PSRR vs. Frequency
Figure 27. Offset Voltage vs. Temperature
1000
–20
–25
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
–85
–90
–95
–100
100
10
1
10
100
1k
10k
100k
1M
10M
100M
100k
1M
10M
100M
1G
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 25. CMRR vs. Frequency
Figure 28. Input Voltage Noise
100
24
22
20
18
16
14
12
10
V
= ±5V
S
10
1
V
= +5V
S
0.1
0.01
100k
1M
10M
100M
1G
–40
–20
0
20
40
60
80
100
FREQUENCY (Hz)
TEMPERATURE (°C)
Figure 26. Output Impedance vs. Frequency
Figure 29. Quiescent Current vs. Temperature for Various Supply Voltages
Rev. 0 | Page 10 of 24
ADA4817-1/ADA4817-2
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
10
70
V
= ±5V
R
= 100ꢀ
S
L
–30
60
50
40
30
–V + V
S
OUT
–70
PHASE
–110
–150
+V – V
S
OUT
+V – V
S
OUT
GAIN
20
10
–190
–230
V
= +5V
S
0
–270
–310
–V + V
S
OUT
–10
10k
100k
1M
10M
100M
1G
10G
–40
–20
0
20
40
60
80
100
FREQUENCY (Hz)
TEMPERATURE (°C)
Figure 30. Output Saturation Voltage vs. Temperature
Figure 31. Open-Loop Gain and Phase vs. Frequency
Rev. 0 | Page 11 of 24
ADA4817-1/ADA4817-2
TEST CIRCUITS
The output feedback pins are used for ease of layout in Figure 32 to Figure 37.
+V
S
+V
S
10µF
10µF
R
R
F
G
0.1µF
0.1µF
0.1µF
0.1µF
V
V
OUT
OUT
V
V
IN
IN
R
R
L
L
49.9ꢀ
10µF
49.9ꢀ
10µF
0.1µF
0.1µF
–V
–V
S
S
Figure 32. G = 1 Configuration
Figure 35. Noninverting Gain Configuration
+V
S
+V
S
10µF
AC
49.9ꢀ
0.1µF
V
OUT
V
OUT
R
L
R
L
49.9ꢀ
AC
10µF
0.1µF
–V
S
–V
S
Figure 33. Positive Power Supply Rejection
Figure 36. Negative Power Supply Rejection
+V
S
+V
S
10µF
10µF
R
R
F
G
1kꢀ
0.1µF
0.1µF
0.1µF
0.1µF
1kꢀ
1kꢀ
V
V
V
OUT
IN
OUT
R
V
SNUB
IN
C
L
R
R
L
L
49.9ꢀ
10µF
53.6ꢀ
1kꢀ
10µF
0.1µF
0.1µF
–V
–V
S
S
Figure 34. Capacitive Load Configuration
Figure 37. Common-Mode Rejection
Rev. 0 | Page 12 of 24
ADA4817-1/ADA4817-2
THEORY OF OPERATION
The ADA4817-1/ADA4817-2 are voltage feedback operational
amplifiers that combine new architecture for FET input opera-
tional amplifiers with the eXtra Fast Complementary Bipolar
(XFCB) process from Analog Devices resulting in an outstanding
combination of speed and low noise. The innovative high speed
FET input stage handles common-mode signals from the nega-
tive supply to within 2.3 V of the positive rail. This stage is
combined with an H-bridge to attain a 870 V/μs slew rate and
low distortion, in addition to 4 nV/√Hz input voltage noise.
The amplifier features a high speed output stage capable of driving
heavy loads sourcing and sinking up to 70 mA of linear current.
Supply current and offset current are laser trimmed for optimum
performance. These specifications make the ADA4817-1/
ADA4817-2 a great choice for high speed instrumentation
and high resolution data acquisition systems. Its low noise,
picoamp input current, precision offset, and high speed make
them superb preamps for fast photodiode applications.
Closed-loop −3 dB frequency
RG
RF + RG
f−3dB = fCROSSOVER
×
(6)
INVERTING CLOSED-LOOP FREQUENCY RESPONSE
Solving for the transfer function,
−2π× fCROSSOVER × RF
RF + RG S + 2π× fCROSSOVER × RG
VO
VI
=
(7)
(8)
(
)
VO
VI
RF
RG
At dc
= −
Solve for closed-loop −3 dB frequency by,
RG
RF + RG
(9)
f−3dB = fCROSSOVER
×
A = (2π × fCROSSOVER)/s
80
CLOSED-LOOP FREQUENCY RESPONSE
The ADA4817-1/ADA4817-2 are classic voltage feedback
amplifiers with an open-loop frequency response that can be
approximated as the integrator response shown in Figure 40.
Basic closed-loop frequency response for inverting and nonin-
verting configurations can be derived from the schematics shown
in Figure 38 and Figure 39.
60
40
20
0
R
F
fCROSSOVER = 410MHz
R
G
V
OUT
A
V
E
V
IN
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 40. Open-Loop Gain vs. Frequency and Basic Connections
Figure 38. Noninverting Configuration
R
F
The closed-loop bandwidth is inversely proportional to the noise
gain of the op amp circuit, (RF + RG)/RG. This simple model is
accurate for noise gains above 2. The actual bandwidth of circuits
with noise gains at or below 2 is higher than those predicted
with this model due to the influence of other poles in the
frequency response of the real op amp.
R
V
G
IN
V
OUT
V
A
E
Figure 39. Inverting Configuration
Figure 41 shows a voltage feedback amplifier’s dc errors. For
both inverting and noninverting configurations,
NONINVERTING CLOSED-LOOP FREQUENCY
RESPONSE
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
RG + RF
RG + RF
Solving for the transfer function,
VOUT
(
error
)
= Ib+ × RS
− Ib− × RF +VOS
RG
RG
2π × fCROSSOVER
RG + RF
VO
VI
=
(4)
(10)
(
RF + RG S + 2π × fCROSSOVER × RG
)
R
F
where fCROSSOVER is the frequency where the amplifier’s open-loop
gain equals 0 dB.
+V
–
OS
R
G
VO RF + RG
I
I
V
OUT
At dc
=
(5)
A
b
–
R
S
VI
RG
V
IN
b+
Figure 41. Voltage Feedback Amplifier’s DC Errors
Rev. 0 | Page 13 of 24
ADA4817-1/ADA4817-2
The voltage error due to Ib+ and Ib– is minimized if RS = RF || RG
(though with the ADA4817-1/ADA4817-2 input currents in the
picoamp range, this is likely not a concern). To include common-
mode effects and power supply rejection effects, total VꢀS can be
modeled by
If this pole occurs too close to the unity-gain crossover point,
the phase margin degrades. This is due to the additional phase
loss associated with the pole.
Note that such capacitance introduces significant peaking in the
frequency response. Larger capacitance values can be driven but
must use a snubbing resistor (RSNUB) at the output of the amplifier,
ΔVS ΔVCM
PSR CMR
VOS =VOS
+
+
(11)
nom
as shown in Figure 42. Adding a small series resistor, RSNUB
,
creates a zero that cancels the pole introduced by the load
where:
VOS
capacitance. Typical values for RSNUB can range from 10 Ω to
50 Ω. The value is typically based on the circuit requirements.
Figure 42 also shows another way to reduce the effect of the
pole created by the capacitive load (CL) by placing a capacitor
(CF) in the feedback loop parallel to the feedback resistor
Typical capacitor values can range from 0.5 pF to 2 pF.
Figure 43 shows the effect of adding a feedback capacitor
to the frequency response.
is the offset voltage specified at nominal conditions.
nom
ΔVS is the change in power supply from nominal conditions.
PSR is the power supply rejection.
ΔVCM is the change in common-mode voltage from nominal
conditions.
CMR is the common-mode rejection.
WIDEBAND OPERATION
+V
S
The ADA4817-1/ADA4817-2 provides excellent performance as a
high speed buffer. Figure 38 shows the circuit used for wideband
characterization for high gains. The impedance at the summing
junction (RF || RG) forms a pole in the amplifier’s loop response
with the amplifier’s input capacitance of 1.5 pF. This pole can
cause peaking and ringing if its frequency is too low. Feedback
resistances of 100 Ω to 400 Ω are recommended, because they
minimize the peaking and they do not degrade the perfor-
mance of the output stage. Peaking in the frequency response
can also be compensated for with a small feedback capacitor
(CF) in parallel with the feedback resistor, or a series resistor
in the noninverting input as shown in Figure 42.
10µF
C
R
F
F
R
G
0.1µF
0.1µF
V
OUT
R
V
SNUB
IN
C
L
R
L
49.9ꢀ
10µF
0.1µF
–V
S
Figure 42. RSNUB or CF Used to Reduce Peaking
THERMAL CONSIDERATIONS
The distortion performance depends on a number of variables:
With 10 V power supplies and 19 mA quiescent current, the
ADA4817-1/ADA4817-2 dissipate 190 mW with no load. This
implies that in the LFCSP, whose thermal resistance is 94°C/W
for the ADA4817-1and 64°C/W for the ADA4817-2, the junction
temperature is typically almost 25° higher than the ambient tem-
perature. The ADA4817-1/ADA4817-2 are designed to maintain
a constant bandwidth over temperature; therefore, an initial ramp
up of the current consumption during warm-up is expected. The
VꢀS temperature drift is below 12 ꢁV/°C; therefore, it can change
up to 0.3 mV due to warm-up effects for an ADA4817-1/
ADA4817-2 in a LFCSP on 10 V. The input bias current
increases by a factor of 1.7 for every 10°C rise in temperature.
•
•
•
•
•
The closed-loop gain of the application
Whether it is inverting or noninverting
Amplifier loading
Signal frequency and amplitude
Board layout
The best performance is usually obtained in the G + 1
configuration with no feedback resistance, big output
load resistors, and small board parasitic capacitances.
DRIVING CAPACITIVE LOADS
In general, high speed amplifiers have a difficult time driving
capacitive loads. This is particularly true in low closed-loop
gains, where the phase margin is the lowest. The difficulty
arises because the load capacitance, CL, forms a pole with the
output resistance, Rꢀ, of the amplifier. The pole can be described
by the following equation:
Heavy loads increase power dissipation and raise the chip
junction temperature as described in the Absolute Maximum
Ratings section. Care should be taken not to exceed the rated
power dissipation of the package.
1
fP
=
(12)
2πROCL
Rev. 0 | Page 14 of 24
ADA4817-1/ADA4817-2
Figure 43 shows the small signal frequency response of the
ADA4817-2 at a gain of 2 vs. CF. At first no CF was used to show
the peaking then two other values of 0.5 pF and 1 pF were used
to show how to reduce the peaking or even eliminate it. As
shown in Figure 43, if the power consumption is a factor in
the system, then using a larger feedback capacitor is acceptable
as long as a feedback capacitor is used across it to control the
peaking. However, if the power consumption is not an issue,
then a lower value feedback resistor such as 100 Ω, would not
require any additional feedback capacitance to maintain flatness
and lower peaking.
POWER-DOWN OPERATION
The ADA4817-1/ADA4817-2 are equipped with separate
power-down pins ( ) pins for each amplifier. This allows the
PD
user the ability to reduce the quiescent supply current when
an amplifier is inactive from 2 mA to 19 mA. The power-down
threshold levels are derived from the voltage applied to the +VS
pin. In 5 V supply application, the enable voltage is greater
than +4 V, and in a 3 V supply application, the enable voltage
is greater than +2 V. However, the amplifier is powered down
whenever the voltage applied to the
pin is 3 V below +VS.
PD
If the
pin is not to be used, it is best to connect it to the
PD
9
NO C
C
= 0.5pF
F
positive supply.
F
6
3
Table 7. Power-Down Voltage Control
PD Pin
5 V
+3 V, −2 V
C
= 1pF
F
Not active
Active
>4 V
<2 V
>2 V
<0 V
0
CAPACITIVE FEEDBACK
–3
–6
–9
Due to package variations and pin-to-pin parasitic between the
single and the dual, the ADA4817-2 has a little more peaking
then the ADA4817-1, especially at a gain of 2. The best way to
tame the peaking is to place a feedback capacitor across the
feedback resistor.
R
G = 2
= 348ꢀ
F
V
V
R
= 10V
= 100mV p-p
S
OUT
= 100ꢀ
L
0.1
1
10
100
1k
10k
FREQUENCY (MHz)
Figure 43. Small Signal Frequency Response vs. Feedback Capacitor
(ADA4817-2)
Rev. 0 | Page 15 of 24
ADA4817-1/ADA4817-2
LAYOUT, GROUNDING, AND BYPASSING CONSIDERATIONS
frequencies but are not always necessary.
Laying out the PCB is usually the last step in the design process
and often proves to be one of the most critical. A brilliant
design can be rendered useless because of poor layout. Because
the ADA4817-1/ADA4817-2 can operate into the RF frequency
spectrum, high frequency board layout considerations must be
taken into account. The PCB layout, signal routing, power
supply bypassing, and grounding all must be addressed to
ensure optimal performance.
Placement of the capacitor returns (grounds) is also important.
Returning the capacitors grounds close to the amplifier load
is critical for distortion performance. Keeping the capacitors
distance short but equal from the load is optimal for performance.
In some cases, bypassing between the two supplies can help
to improve PSRR and to maintain distortion performance in
crowded or difficult layouts. It is another option to improve
performance.
SIGNAL ROUTING
Minimizing the trace length and widening the trace from the
capacitors to the amplifier reduces the trace inductance. A
series inductance with the parallel capacitance can form a
tank circuit, which can introduce high frequency ringing at
the output. This additional inductance can also contribute to
increased distortion due to high frequency compression at the
output. The use of vias should be minimized in the direct path
to the amplifier power supply pins because vias can introduce
parasitic inductance, which can lead to instability. When
required to use vias, choose multiple large diameter vias
because this lowers the equivalent parasitic inductance.
The ADA4817-1/ADA4817-2 feature the new low distortion
pinout with a dedicated feedback pin that allows a compact
layout. The dedicated feedback pin reduces the distance from
the output to the inverting input, which greatly simplifies the
routing of the feedback network.
When laying out the ADA4817-1/ADA4817-2 as a unity-gain
amplifier, it is recommended that a short, but wide, trace be
placed between the dedicated feedback pins, and the inverting
input to the amplifier be used to minimize stray parasitic
inductance.
To minimize parasitic inductances, ground planes should be
used under high frequency signal traces. However, the ground
plane should be removed from under the input and output pins
to minimize the formation of parasitic capacitors, which degrades
phase margin. Signals that are susceptible to noise pickup
should be run on the internal layers of the PCB, which can
provide maximum shielding.
GROUNDING
The use of ground and power planes is encouraged as a method
of providing low impedance returns for power supply and signal
currents. Ground and power planes can also help to reduce stray
trace inductance and to provide a low thermal path for the
amplifier. Ground and power planes should not be used under
any of the pins. The mounting pads and the ground or power
planes can form a parasitic capacitance at the amplifier’s input.
Stray capacitance on the inverting input and the feedback
resistor form a pole, which degrades the phase margin, leading
to instability. Excessive stray capacitance on the output also
forms a pole, which degrades phase margin.
POWER SUPPLY BYPASSING
Power supply bypassing is a critical aspect of the PCB design
process. For best performance, the ADA4817-1/ADA4817-2
power supply pins need to be properly bypassed.
A parallel connection of capacitors from each of the power
supply pins to ground works best. Paralleling different values
and sizes of capacitors helps to ensure that the power supply
pins see a low ac impedance across a wide band of frequencies.
This is important for minimizing the coupling of noise into the
amplifier. Starting directly at the power supply pins, the smallest
value and sized component should be placed on the same side
of the board as the amplifier, and as close as possible to the
amplifier, and connected to the ground plane. This process
should be repeated for the next larger value capacitor. It is
recommended that a 0.1 ꢁF ceramic 0508 case be used for the
ADA4817-1/ADA4817-2. The 0508 offers low series inductance
and excellent high frequency performance. The 0.1 ꢁF provides
low impedance at high frequencies. A 10 ꢁF electrolytic capa-
citor should be placed in parallel with the 0.1 ꢁF. The 10 ꢁF
capacitor provides low ac impedance at low frequencies. Smaller
values of electrolytic capacitors may be used depending on the
circuit requirements. Additional smaller value capacitors help to
provide a low impedance path for unwanted noise out to higher
EXPOSED PADDLE
The ADA4817-1/ADA4817-2 feature an exposed paddle, which
lowers the thermal resistance by 25% compared to a standard
SꢀIC plastic package. The exposed paddle of the ADA4817-1/
ADA4817-2 floats internally which provides the maximum
flexibility and ease of use. It can be connected to the ground
plane or to the negative power supply plane. In cases where
thermal heating is not an issue, the exposed pad could be left
floating.
The use of thermal vias or heat pipes can also be incorporated
into the design of the mounting pad for the exposed paddle.
These additional vias help to lower the overall junction-to-
ambient temperature (θJA). Using a heavier weight copper on
the surface to which the amplifier’s exposed paddle is soldered
can greatly reduce the overall thermal resistance seen by the
ADA4817-1/ADA4817-2.
Rev. 0 | Page 16 of 24
ADA4817-1/ADA4817-2
LEAKAGE CURRENTS
INPUT CAPACITANCE
Poor PCB layout, contaminants, and the board insulator
material can create leakage currents that are much larger than
the input bias current of the ADA4817-1/ADA4817-2. Any
voltage differential between the inputs and nearby runs sets
up leakage currents through the PCB insulator, for example, 1 V/
100 GΩ = 10 pA. Similarly, any contaminants, such as skin oils
on the board, can create significant leakage. To reduce leakage
significantly, put a guard ring (shield) around the inputs and
input leads that are driven to the same voltage potential as the
inputs. This way there is no voltage potential between the inputs
and surrounding area to set up any leakage currents. For the
guard ring to be completely effective, it must be driven by a
relatively low impedance source and should completely
surround the input leads on all sides (above and below)
while using a multilayer board.
Along with bypassing and ground, high speed amplifiers can be
sensitive to parasitic capacitance between the inputs and ground.
A few picofarads of capacitance reduces the input impedance at
high frequencies, in turn increasing the amplifier’s gain, causing
peaking of the frequency response or even oscillations if severe
enough. It is recommended that the external passive components
connected to the input pins be placed as close as possible to the
inputs to avoid parasitic capacitance. The ground and power
planes must be kept at a small distance from the input pins on
all layers of the board.
INPUT-TO-INPUT/OUTPUT COUPLING
To minimize capacitive coupling between the inputs and
outputs, the output signal traces should not be parallel with
the inputs. In addition, the input traces should not be very
close to each other. A minimum of 7 mils between the two
inputs is recommended.
Another effect that can cause leakage currents is the charge
absorption of the insulator material itself. Minimizing the amount
of material between the input leads and the guard ring helps to
reduce the absorption. In addition, low absorption materials,
such as Teflon® or ceramic, can be necessary in some instances.
Rev. 0 | Page 17 of 24
ADA4817-1/ADA4817-2
APPLICATIONS INFORMATION
The stable bandwidth attainable with this preamp is a function
of RF, the gain bandwidth product of the amplifier, and the total
capacitance at the amplifier’s summing junction, including the
photodiode capacitance (CS) and the amplifier input capacitance.
RF and the total capacitance produce a pole in the amplifier’s
loop transmission that can result in peaking and instability.
Adding CF creates a zero in the loop transmission that compen-
sates for the pole’s effect and reduces the signal bandwidth. It
can be shown that the signal bandwidth obtained with a 45°
phase margin (f(45)) is defined by
LOW DISTORTION PINOUT
The ADA4817-1/ADA4817-2 feature a new low distortion
pinout from Analog Devices. The new pinout provides two
advantages over the traditional pinout. The first advantage is
improved second harmonic distortion performance, which is
accomplished by the physical separation of the noninverting
input pin and the negative power supply pin. The second
advantage is the simplification of the layout due to the dedi-
cated feedback pin and easy routing of the gain set resistor
back to the inverting input pin. This allows a compact layout,
which helps to minimize parasitics and increase stability.
fCR
f(45)
=
(14)
2π× RF ×(CS + CM + CD )
The designer does not need to use the dedicated feedback pin to
provide feedback for the ADA4817-1/ADA4817-2. The output
pin of the ADA4817-1/ADA4817-2 can still be used to provide
feedback to the inverting input of the ADA4817-1/ADA4817-2.
where:
CR is the amplifier crossover frequency.
RF is the feedback resistor.
f
CS is the source capacitance including the photodiode and the
board parasitic.
CM is the common-mode capacitance of the amplifier.
WIDEBAND PHOTODIODE PREAMP
The wide bandwidth and low noise of the ADA4817-1/
ADA4817-2 make it an ideal choice for transimpedance
amplifiers, such as those used for signal conditioning with
high speed photodiodes. Figure 44 shows an I/V converter
with an electrical model of a photodiode. The basic transfer
function is
CD is the differential capacitance of the amplifier.
The value of CF that produces f(45) can be shown to be
CS + CM + CD
2π × RF × fCR
CF =
(15)
I
PHOTO × RF
VOUT
=
(13)
The frequency response shows less peaking if bigger CF values
are used.
1+ sCF RF
where:
PHOTO is the output current of the photodiode.
The parallel combination of RF and CF sets the signal bandwidth.
The preamplifier output noise over frequency is shown in
Figure 45.
I
1
C
F
f1
f2
f3
=
=
=
2
R (C + C + C + C )
F F S M D
1
2
R C
F
F
R
F
fCR
(C + C + C + C )/C
F
F
S
M
D
R
NOISE
11
= 10 ꢀ
SH
C
C
F
I
R
M
PHOTO
C
VEN (C + C + C + C )/C
F
f3
S
F
S
M
D
C
D
V
f2
OUT
M
f1
VEN
V
B
NOISE DUE TO AMPLIFIER
FREQUENCY (Hz)
Figure 44. Wideband Photodiode Preamp
Figure 45. Photodiode Voltage Noise Contributions
Rev. 0 | Page 18 of 24
ADA4817-1/ADA4817-2
45
40
35
30
25
20
15
10
5
bandwidth extends past the preamp signal bandwidth and
is eventually rolled off by the decreasing loop gain of the
amplifier. The current equivalent noise from the inverting
terminal is typically negligible for most applications. The
innovative architecture used in the ADA4817-1/ADA4817-2
makes balancing both inputs unnecessary, as opposed to
traditional FET input amplifiers. Therefore, minimizing the
impedance seen from the noninverting terminal to ground at
all frequencies is critical for optimal noise performance.
Integrating the square of the output voltage noise spectral
density over frequency and then taking the square root allows
users to obtain the total rms output noise of the preamp. Table 8
summarizes approximations for the amplifier and feedback and
source resistances. Noise components for an example preamp
with RF = 50 kΩ, CS = 30 pF, and CF = 0.5 pF (bandwidth of
about 6.4 MHz) are also listed.
G = 63V/V
R
= 100ꢀ
L
S
OUT
0
V
V
= 10V
= 6V p-p
–5
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 46. Photodiode Preamp Frequency Response
The pole in the loop transmission translates to a zero in the
amplifier’s noise gain, leading to an amplification of the
input voltage noise over frequency. The loop transmission
zero introduced by CF limits the amplification. The noise gain
Table 8. RMS Noise Contributions of Photodiode Preamp
Contributor
Expression
RMS Noise with RF = 50 kΩ, CS = 30 pF, CF = 0.5 pF
RF
94 μV
4kT × RF × f2 ×1.57
VEN Amp
IEN Amp
777.5 μV
CS + CM + C D + CF
VEN ×
× f3 ×1.57
CF
0.4 μV
IEN ×RF × f2 ×1.57
783 μV (total)
Rev. 0 | Page 19 of 24
ADA4817-1/ADA4817-2
approximated by:
In-amp−3 dB = (fCR × RG)/(2 × RF)
HIGH SPEED JFET INPUT INSTRUMENTATION
AMPLIFIER
Figure 47 shows an example of a high speed instrumentation
amplifier with a high input impedance using the ADA4817-1/
ADA4817-2. The dc transfer function is
Common-mode rejection of the in-amp is primarily deter-
mined by the match of resistor ratios, R1:R2 to R3:R4. It can
be estimated by
VO
VCM
(
δ1− δ2
)
δ2
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
2RF
RG
=
(17)
(16)
VOUT
=
(
VN −VP
)
1 +
(
1+ δ1
)
The summing junction impedance for the preamps is equal
to RF || 0.5(RG). Keep this value relatively low to improve the
bandwidth response like in the previous example.
For G = 1, it is recommended that the feedback resistors for the
two preamps be set to 0 Ω and the gain resistor be open. The
system bandwidth for G = 1 is 400 MHz. For gains higher than
2, the bandwidth is set by the preamp, and it can be
V
CC
0.1µF
10µF
R
S1
R2
350ꢀ
V
N
ADA4817-2
U1
V
CC
0.1µF
10µF
V
0.1µF
10µF
EE
R1
350ꢀ
R
= 500ꢀ
F
V
O
ADA4817-1
R
G
R3
350ꢀ
R
= 500ꢀ
F
0.1µF
10µF
V
CC
R4
350ꢀ
V
EE
0.1µF
10µF
ADA4817-2
U2
R
S2
0.1µF
10µF
V
P
V
EE
Figure 47. High Speed Instrumentation Amplifier
Rev. 0 | Page 20 of 24
ADA4817-1/ADA4817-2
Resistor values are kept low for minimal noise contribution,
offset voltage, and optimal frequency response. Due to the low
capacitance values used in the filter circuit, the PCB layout and
minimization of parasitics is critical. A few picofarads can detune
the corner frequency, fc, of the filter. The capacitor values shown
in Figure 49 actually incorporate some stray PCB capacitance.
ACTIVE LOW-PASS FILTER (LPF)
Active filters are used in many applications such as antialiasing
filters and high frequency communication IF strips.
With a 410 MHz gain bandwidth product and high slew rate,
the ADA4817-1/ADA4817-2 is an ideal candidate for active
filters. Moreover, thanks to the low input bias current provided
by the FET stage, the ADA4817-1/ADA4817-2 eliminate any dc
errors. Figure 48 shows the frequency response of 90 MHz and
45 MHz LPFs. In addition to the bandwidth requirements, the
slew rate must be capable of supporting the full power band-
width of the filter. In this case, a 90 MHz bandwidth with a
2 V p-p output swing requires at least 870 V/μs. This per-
formance is achievable at 90 MHz only because of the wide
bandwidth and high slew rate of the ADA4817-1/ADA4817-2.
Capacitor selection is critical for optimal filter performance.
Capacitors with low temperature coefficients, such as NPO
ceramic capacitors and silver mica, are good choices for filter
elements.
15
12
9
6
3
0
–3
OUT2, f = 90MHz
OUT1, f = 90MHz
–6
The circuit shown in Figure 49 is a 4-pole, Sallen-Key, low-pass
filter (LPF). The filter comprises two identical cascaded Sallen-
Key LPF sections, each with a fixed gain of G = 2. The net gain
of the filter is equal to G = 4 or 12 dB. The actual gain shown in
Figure 48 is 12 dB. This does not take into account the output
voltage being divided in half by the series matching termination
resistor, RT, and the load resistor.
–9
–12
–15
–18
–21
–24
–27
–30
–33
–36
–39
–42
OUT1, f = 45MHz
OUT2, f = 45MHz
Setting the resistors equal to each other greatly simplifies the
design equations for the Sallen-Key filter. To achieve 90 MHz
the value of R should be set to 182 Ω. However, if the value of R
is doubled, the corner frequency is cut in half to 45 MHz. This
would be an easy way to tune the filter by simply multiplying
the value of R (182 Ω) by the ratio of 90 MHz and the new
corner frequency in megahertz. Figure 48 shows the output of
each stage is of the filter and the two different filters corres-
ponding to R = 182 Ω and R = 365 Ω. It is not recommended
to increase the corner frequency beyond 90 MHz due to
bandwidth and slew rate limitations unless unity-gain stages
are acceptable.
100k
1M
10M
100M
1G
FREQUENCY (Hz)
Figure 48. Low-Pass Filter Response
C1
3.9pF
C3
3.9pF
10µF
+5V
U1
10µF
+5V
U2
0.1µF
0.1µF
R
R
+IN1
R
R
R
T
R
C2
5.6pF
T
49.9Ω
10µF
49.9Ω
OUT2
OUT1
C4
5.6pF
10µF
0.1µF
0.1µF
–5V
–5V
R2
R1
348Ω
R4
348Ω
R3
348Ω
348Ω
Figure 49. 4-Pole Sallen-Key Low-Pass Filter (ADA4817-2)
Rev. 0 | Page 21 of 24
ADA4817-1/ADA4817-2
1.2
0.8
0.15
90MHz
90MHz
0.10
0.05
0
45MHz
45MHz
0.4
0
–0.4
–0.8
–1.2
–0.05
–0.10
–0.15
TIME (5ns/DIV)
TIME (5ns/DIV)
Figure 51. Large Signal Transient Response (Low-Pass Filter)
Figure 50. Small Signal Transient Response (Low-Pass Filter)
Rev. 0 | Page 22 of 24
ADA4817-1/ADA4817-2
OUTLINE DIMENSIONS
3.25
3.00 SQ
2.75
0.60 MAX
5
0.50
BSC
0.60 MAX
8
2.95
2.75 SQ
2.55
1.60
1.45
1.30
EXPOSED
PAD
TOP
VIEW
PIN 1
INDICATOR
(BOTTOM VIEW)
4
1
PIN 1
INDICATOR
0.50
0.40
0.30
1.89
1.74
1.59
12° MAX
0.70 MAX
0.65TYP
0.90 MAX
0.85 NOM
0.05 MAX
0.01 NOM
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.30
0.23
0.18
SEATING
PLANE
0.20 REF
SECTION OF THIS DATA SHEET.
Figure 52. 8-Lead Lead Frame Chip Scale Package [LFCSP_VD]
3 mm × 3 mm Body, Very Thin, Dual Lead (CP-8-2)
Dimensions shown in millimeters
4.00
BSC SQ
0.60 MAX
(BOTTOM VIEW)
0.60 MAX
PIN 1
INDICATOR
13
12
16
1
4
PIN 1
INDICATOR
0.65 BSC
2.25
2.10 SQ
1.95
TOP
VIEW
3.75
BSC SQ
0.75
0.60
0.50
9
8
5
0.25 MIN
0.80 MAX
0.65 TYP
12° MAX
1.95 BSC
0.05 MAX
0.02 NOM
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
1.00
0.85
0.80
0.35
0.30
0.25
0.20 REF
COPLANARITY
0.08
SECTION OF THIS DATA SHEET.
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VGGC
Figure 53.16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad (CP-16-4)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
Package Description
8-Lead LFCSP_VD
8-Lead LFCSP_VD
8-Lead LFCSP_VD
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
Package Option
CP-8-2
CP-8-2
Ordering Quantity
Branding
H1F
H1F
ADA4817-1ACPZ-R21
ADA4817-1ACPZ-RL1
ADA4817-1ACPZ-R71
ADA4817-2ACPZ-R21
ADA4817-2ACPZ-RL1
ADA4817-2ACPZ-R71
250
5,000
1,500
250
5,000
1,500
CP-8-2
H1F
CP-16-4
CP-16-4
CP-16-4
1 Z = RoHS Compliant Part.
Rev. 0 | Page 23 of 24
ADA4817-1/ADA4817-2
NOTES
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07756-0-11/08(0)
Rev. 0 | Page 24 of 24
相关型号:
©2020 ICPDF网 联系我们和版权申明