AD840SE-883B [ADI]
Wideband, Fast Settling Op Amp; 宽带,快速建立运算放大器型号: | AD840SE-883B |
厂家: | ADI |
描述: | Wideband, Fast Settling Op Amp |
文件: | 总8页 (文件大小:420K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Wideband,
Fast Settling Op Amp
a
AD840
FEATURES
CONNECTION DIAGRAMS
Wideband AC Performance
Plastic DIP (N) Package
LCC (E) Package
Gain Bandwidth Product: 400 MHz (Gain ≥ 10)
Fast Settling: 100 ns to 0.01% for a 10 V Step
Slew Rate: 400 V/s
and
Stable at Gains of 10 or Greater
Full Power Bandwidth: 6.4 MHz for 20 V p-p into a
500 ⍀ Load
Precision DC Performance
Input Offset Voltage: 0.3 mV max
Input Offset Drift: 3 V/؇C typ
Input Voltage Noise: 4 nV/√Hz
Open-Loop Gain: 130 V/mV into a 1 k⍀ Load
Output Current: 50 mA min
Supply Current: 12 mA max
APPLICATIONS
Video and Pulse Amplifiers
DAC and ADC Buffers
Line Drivers
Available in 14-Pin Plastic DIP, Hermetic Cerdip
and 20-Pin LCC Packages and in Chip Form
MIL-STD-883B Processing Available
bandwidth active filters. The extremely rapid settling time of the
AD840 makes it the preferred choice for data acquisition appli-
cations which require 12-bit accuracy. The AD840 is also ap-
propriate for other applications such as high speed DAC and
ADC buffer amplifiers and other wide bandwidth circuitry.
APPLICATION HIGHLIGHTS
1. The high slew rate and fast settling time of the AD840 make
it ideal for DAC and ADC buffers, line drivers and all types
of video instrumentation circuitry.
PRODUCT DESCRIPTION
The AD840 is a member of the Analog Devices’ family of wide
bandwidth operational amplifiers. This high speed/high precision
family includes, among others, the AD841, which is unity-
gain stable, and the AD842, which is stable at a gain of two or
greater and has 100 mA minimum output current drive. These
devices are fabricated using Analog Devices’ junction isolated
complementary bipolar (CB) process. This process permits a
combination of dc precision and wideband ac performance
previously unobtainable in a monolithic op amp. In addition
to its 400 MHz gain bandwidth product, the AD840 offers
extremely fast settling characteristics, typically settling to within
0.01% of final value in 100 ns for a 10 volt step.
2. The AD840 is truly a precision amplifier. It offers 12-bit
accuracy to 0.01% or better and wide bandwidth, perfor-
mance previously available only in hybrids.
3. The AD840’s thermally balanced layout and the high speed
of the CB process allow the AD840 to settle to 0.01% in
100 ns without the long “tails” that occur with other fast op
amps.
4. Laser wafer trimming reduces the input offset voltage to
0.3 mV max on the K grade, thus eliminating the need for
external offset nulling in many applications. Offset null pins
are provided for additional versatility.
The AD840 remains stable over its full operating temperature
range at closed-loop gains of 10 or greater. It also offers a low
quiescent current of 12 mA maximum, a minimum output
current drive capability of 50 mA, a low input voltage noise of
4 nV/√Hz and a low input offset voltage of 0.3 mV maximum
(AD840K).
5. Full differential inputs provide outstanding performance
in all standard high frequency op amp applications where
circuit gain will be 10 or greater.
6. The AD840 is an enhanced replacement for the HA2540.
The 400 V/µs slew rate of the AD840, along with its 400 MHz
gain bandwidth, ensures excellent performance in video and
pulse amplifier applications. This amplifier is ideally suited for
use in high frequency signal conditioning circuits and wide
REV. C
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
(@ +25؇C and ؎15 V dc, unless otherwise noted)
AD840–SPECIFICATIONS
Model
AD840J
Typ
AD840K
AD840S
Typ
Conditions
Min
Max
Min
Typ
Max
Min
Max
Units
INPUT OFFSET VOLTAGE1
TMIN–TMAX
0.2
1
1.5
0.1
0.3
0.7
0.2
1
2
mV
mV
Offset Drift
5
3
5
µV/°C
INPUT BIAS CURRENT
TMIN–TMAX
3.5
8
10
3.5
5
6
3.5
8
12
µA
µA
INPUT OFFSET CURRENT
TMIN–TMAX
0.1
0.4
0.5
0.1
0.2
0.3
0.1
0.4
0.6
µA
µA
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Differential Mode
30
2
30
2
30
2
kΩ
pF
INPUT VOLTAGE RANGE
Common Mode
Common-Mode Rejection
؎10
90
85
12
110
؎10
106
90
12
115
±10
90
85
12
110
V
dB
dB
VCM = ±10 V
TMIN–TMAX
INPUT VOLTAGE NOISE
Wideband Noise
f = 1 kHz
10 Hz to 10 MHz
4
10
4
10
4
10
nV/√Hz
µV rms
OPEN-LOOP GAIN
VO = ±10 V
RLOAD = 1 kΩ
TMIN–TMAX
RLOAD = 500 Ω
TMIN–TMAX
100
50
75
130
80
100
75
100
75
130
100
100
50
75
50
130
80
V/mV
V/mV
V/mV
V/mV
50
OUTPUT CHARACTERISTICS
Voltage
RLOAD ≥ 500 Ω
TMIN–TMAX
؎10
؎10
؎10
V
Current
Output Resistance
VOUT = ±10 V
Open Loop
50
50
50
mA
Ω
15
15
15
FREQUENCY RESPONSE
Gain Bandwidth Product
VOUT = 90 mV p-p
AV = –10
400
400
400
MHz
Full Power Bandwidth2
VO = 20 V p-p
RLOAD = 500 Ω
AV = –10
AV = –10
AV = –10
5.5
6.4
10
20
5.5
6.4
10
20
5.5
6.4
10
20
MHz
ns
%
Rise Time
Overshoot3
Slew Rate3
350
400
350
400
350
400
V/µs
Settling Time3 – 10 V Step
AV = –10
to 0.1%
to 0.01%
80
100
80
100
80
100
ns
ns
OVERDRIVE RECOVERY
–Overdrive
+Overdrive
190
350
190
350
190
350
ns
ns
DIFFERENTIAL GAIN
DIFFERENTIAL PHASE
f = 4.4 MHz
f = 4.4 MHz
0.025
0.04
0.025
0.04
0.025
0.04
%
Degree
POWER SUPPLY
Rated Performance
Operating Range
Quiescent Current
±15
12
±15
12
±15
12
V
V
mA
mA
dB
dB
؎5
؎18
14
16
؎5
؎18
14
16
؎5
؎18
14
18
TMIN–TMAX
VS = ±5 V to ±18 V
TMIN–TMAX
Power Supply Rejection Ratio
90
80
100
94
86
100
90
80
100
TEMPERATURE RANGE
Rated Performance4
0
+75
0
+75
–55
+125
°C
TRANSISTOR COUNT
# of Transistors
72
72
72
–2–
REV. C
AD840
NOTES
1Input offset voltage specifications are guaranteed after 5 minutes at TA = +25°C.
2Full power bandwidth = slew rate/2 π VPEAK
.
3Refer to Figures 22 and 23.
4“S” grade TMIN–TMAX specifications are tested with automatic test equipment at TA = –55°C and TA = +125°C.
All min and max specifications are guaranteed. Specifications shown in boldface are tested on all production units.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS1
Plastic DIP (N) Package
and
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V
Internal Power Dissipation2
Cerdip (Q) Package
Plastic (N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 W
Cerdip (Q) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 W
LCC (E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 W
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . ±6 V
Storage Temperature Range
Q, E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–65°C to +150°C
N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–65°C to +125°C
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . +175°C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300°C
NOTES
1Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only, and functional
operation of the device at these or any other conditions above those indicated in
the operational section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2Maximum internal power dissipation is specified so that TJ does not exceed
+175°C at an ambient temperature of +25°C.
LCC (E) Package
Thermal Characteristics:
θJC
θJA
Derate at
Cerdip Package
Plastic Package
LCC Package
30°C/W
30°C/W
35°C/W
110°C/W
100°C/T
150°C/W
8.7 mW/°C
10 mW/°C
6.7 mW/°C
Recommended Heat Sink:
Aavid Engineering© #602B
ORDERING GUIDE
Package Options2
Models
AD840JN
AD840KN
AD840JQ
AD840KQ
N-14
N-14
Q-14
Q-14
Q-14
Q-14
Q-14
E-20A
E-20A
AD840 Connection Diagrams
METALIZATION PHOTOGRAPH
Contact factory for latest dimensions.
Dimensions shown in inches and (mm).
AD840SQ
AD840SQ-883B
5962-89640012A
AD840SE-883B
5962-8964001CA
NOTES
1J and S Grade Chips also available.
2N = Plastic DIP; Q = Cerdip; E = LCC (Leadless
2Ceramic Chip Carrier).
REV. C
–3–
AD840–Typical Characteristics
(at +25؇C and VS = ؎15 V, unless otherwise noted)
Figure 1. Input Common-Mode
Range vs. Supply Voltage
Figure 2. Output Voltage Swing
vs. Supply Voltage
Figure 3. Output Voltage Swing
vs. Load Resistance
Figure 5. Input Bias Current vs.
Temperature
Figure 4. Quiescent Current vs.
Supply Voltage
Figure 6. Output Impedance vs.
Frequency
Figure 8. Short-Circuit Current
Limit vs. Temperature
Figure 9. Gain Bandwidth Product
vs. Temperature
Figure 7. Quiescent Current vs.
Temperature
–4–
REV. C
AD840
Figure 11. Open-Loop Gain vs.
Supply Voltage
Figure 12. Power Supply Rejection
vs. Frequency
Figure 10. Open-Loop Gain and
Phase Margin Phase vs. Frequency
Figure 15. Output Swing and
Error vs. Settling Time
Figure 14. Large Signal Frequency
Response
Figure 13. Common-Mode
Rejection vs. Frequency
Figure 17. Input Voltage Noise
Spectral Density
Figure 18. Slew Rate vs.
Temperature
Figure 16. Harmonic Distortion vs.
Frequency
REV. C
–5–
AD840
Figure 19b. Inverter Large Signal
Pulse Response
Figure 19a. Inverting Amplifier
Configuration (DIP Pinout)
Figure 19c. Inverter Small Signal
Pulse Response
Figure 20a. Noninverting Amplifier
Configuration (DIP Pinout)
Figure 20c. Noninverting Small
Signal Pulse Response
Figure 20b. Noninverting Large
Signal Pulse Response
OFFSET NULLING
The input offset voltage of the AD840 is very low for a high
speed op amp, but if additional nulling is required, the circuit
shown in Figure 21 can be used.
Figure 21. Offset Nulling (DIP Pinout)
–6–
REV. C
Applying the AD840
AD840 SETTLING TIME
Figures 22 and 24 show the settling performance of the AD840
in the test circuit shown in Figure 23.
Figure 24 shows the “long-term” stability of the settling charac-
teristics of the AD840 output after a 10 V step. There is no evi-
dence of settling tails after the initial transient recovery time.
The use of a junction isolated process, together with careful lay-
out, avoids these problems by minimizing the effects of transis-
tor isolation capacitance discharge and thermally induced shifts
in circuit operating points. These problems do not occur even
under high output current conditions.
Settling time is defined as:
The interval of time from the application of an ideal step
function input until the closed-loop amplifier output has
entered and remains within a specified error band.
This definition encompasses the major components which com-
prise settling time. They include (1) propagation delay through
the amplifier; (2) slewing time to approach the final output
value; (3) the time of recovery from the overload associated with
slewing; and (4) linear settling to within the specified error band.
Expressed in these terms, the measurement of settling time is
obviously a challenge and needs to be done accurately to assure
the user that the amplifier is worth consideration for the
application.
Figure 24. AD840 Settling Demonstrating No Settling Tails
GROUNDING AND BYPASSING
In designing practical circuits with the AD840, the user must re-
member that whenever high frequencies are involved, some spe-
cial precautions are in order. Circuits must be built with short
interconnect leads. Large ground planes should be used when-
ever possible to provide a low resistance, low inductance circuit
path, as well as minimizing the effects of high frequency cou-
pling. Sockets should be avoided, because the increased
inter-lead capacitance can degrade bandwidth.
Figure 22. AD840 0.01% Settling Time
Feedback resistors should be of low enough value to assure that
the time constant formed with the circuit capacitances will not
limit the amplifier performance. Resistor values of less than
5 kΩ are recommended. If a larger resistor must be used, a small
(±10 pF) feedback capacitor in connected parallel with the feed-
back resistor, RF, may be used to compensate for these stray ca-
pacitances and optimize the dynamic performance of the
amplifier in the particular application.
TEK
TEK
ERROR
7A13
AMP
(x11)
7603
TEK
OSCILLOSCOPE
7A18
HP6263
Ω
Ω
Ω
4.99k
499
DDD5109
FLAT-TOP
PULSE
Ω
4.99k
499
0.1µF
Ω
50
+15V
GENERATOR
2.2µF
Power supply leads should be bypassed to ground as close as
possible to the amplifier pins. A 2.2 µF capacitor in parallel with
a 0.1 µF ceramic disk capacitor is recommended.
11
4
FET PROBE
TEK P6201
10
AD840
5
6
0.1µF
Ω
499
CAPACITIVE LOAD DRIVING ABILITY
499Ω
2.2µF
Like all wideband amplifiers, the AD840 is sensitive to capaci-
tive loading. The AD840 is designed to drive capacitive loads
of up to 20 pF without degradation of its rated performance.
Capacitive loads of greater than 20 pF will decrease the dynamic
performance of the part although instability should not occur
unless the load exceeds 100 pF. A resistor in series with the out-
put can be used to decouple larger capacitive loads.
-15V
Figure 23. Settling Time Test Circuit
Figure 23 shows how measurement of the AD840’s 0.01% set-
tling in 100 ns was accomplished by amplifying the error signal
from a false summing junction with a very high speed propri-
etary hybrid error amplifier specially designed to enable testing
of small settling errors. The device under test was driving a
420 Ω load. The input to the error amp is clamped in order to
avoid possible problems associated with the overdrive recovery
of the oscilloscope input amplifier. The error amp amplifies the
error from the false summing junction by 11, and it contains a
gain vernier to fine trim the gain.
USING A HEAT SINK
The AD840 draws less quiescent power than most high speed
amplifiers and is specified for operation without a heat sink.
However, when driving low impedance loads the current to the
load can be 4 to 5 times the quiescent current. This will create a
noticeable temperature rise. Improved performance can be
achieved by using a small heat sink such as the Aavid Engineer-
ing #602B.
REV. C
–7–
AD840
HIGH SPEED DAC BUFFER CIRCUIT
OVERDRIVE RECOVERY
The AD840’s 100 ns settling time to 0.01% for a 10 V step
makes it well suited as an output buffer for high speed D/A con-
verters. Figure 25 shows the connections for producing a 0 to
+10.24 V output swing from the AD568 35 ns DAC. With the
AD568 in unbuffered voltage output mode, the AD840 is
placed in noninverting configuration. As a result of the 1 kΩ
span resistor provided internally in the AD568, the noise gain of
this topology is 10. Only 5 pF is required across the feedback
(span) resistor to optimize settling.
Figure 26 shows the overdrive recovery capability of the AD840.
Typical recovery time is 190 ns from negative overdrive and
350 ns from positive overdrive.
Figure 26. Overdrive Recovery
Figure 27. Overdrive Recovery Test Circuit
Figure 25. 0 V to +10.24 V DAC Output Buffer
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
14-Pin Cerdip (Q) Package
14-Pin Plastic (N) Package
20-Pin LCC (E) Package
–8–
REV. C
相关型号:
AD840SE/883B
IC OP-AMP, 1000 uV OFFSET-MAX, 400 MHz BAND WIDTH, CQCC20, CERAMIC, LCC-20, Operational Amplifier
ADI
AD840SQ/883B
IC OP-AMP, 1000 uV OFFSET-MAX, 400 MHz BAND WIDTH, CDIP14, CERDIP-14, Operational Amplifier
ADI
©2020 ICPDF网 联系我们和版权申明