AD8363ACPZ-R7 [ADI]
50 Hz to 6 GHz 50 dB TruPwr Detector; 50 Hz至6 GHz的50分贝TruPwr检测器型号: | AD8363ACPZ-R7 |
厂家: | ADI |
描述: | 50 Hz to 6 GHz 50 dB TruPwr Detector |
文件: | 总14页 (文件大小:3728K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
50 Hz to 6 GHz
50 dB TruPwr™ Detector
AD8363
Preliminary Technical Data
FEATURES
Accurate RMS-to-DC conversion from 50 Hz to 6 GHz
Single ended input dynamic range of >50 dB
Waveform and modulation independent, such as
WiMAX/GSM/CDMA/WCDMA/TDMA
Linear-in-decibels output, scaled 50 mV/dB
Log conformance error of <0.3 dB
Temperature stability of < 0.5 dB
Voltage supply range of 4.5 V to 5.5 V
Operating temperature range of −40°C to +125°C
Power-down capability
APPLICATIONS
Power amplifier linearization/control loops
Transmitter power controls
Transmitter signal strength indication (TSSI)
RF instrumentation
FUNCTIONAL BLOCK DIAGRAM
Figure 1.
GENERAL DESCRIPTION
The AD8363 is a true RMS responding power detector that has
more than 50 dB measurement range when driven with a
single-ended 50 Ω source. The device provides a solution in a
variety of high frequency communication systems, and in
instrumentation, requiring an accurate response to signal
power. The AD8363 is easy to use with its single-ended 50 Ω
input, only requiring a single 5 V supply, and a few capacitors.
The AD8363 can operate from arbitrarily low frequencies to 6
GHz and can accept inputs that have RMS values from less than
-50 dBm to at least 0 dBm, with large crest factors, exceeding
the requirements for accurate measurement of WiMAX,
WCDMA, and CDMA signals.
Used as a power measurement device, VOUT is connected to
VSET. The output is then proportional to the logarithm of the
RMS value of the input. In other words, the reading is
presented directly in decibels and is conveniently scaled 1 V per
decade, or 50 mV/dB; other slopes are easily arranged. In
controller mode, the voltage applied to VSET determines the
power level required at the input to null the deviation from the
set point. The output buffer can provide high load currents.
The AD8363 has 1.5 mW power consumption when powered
down by a logic high applied to pin 1, TCM2. It powers up
within about 30 μs to its nominal operating current of 60 mA at
25°C. The AD8363 is supplied in a 4 mm x 4 mm, 16-lead
LFCSP for operation over the temperature range of −40°C to
+125°C. An evaluation board is available.
The AD8363 can determine the true power of a high frequency
signal having a complex low frequency modulation envelope, or
can be used as a simple low frequency RMS voltmeter. The
high-pass corner generated by its internal offset-nulling loop
can be lowered by a capacitor added on the CHPF pin.
Rev. PrB
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2008 Analog Devices, Inc. All rights reserved.
AD8363
Preliminary Technical Data
SPECIFICATIONS
Pins 3, 10 - VPOS = VS = 5 V, T = 25°C, ZO = 50 Ω, Single ended input drive, VOUT tied to VSET, VTGT = 1.4, CLPF= 3.9 nF, CHPF=2.7 nF,
Error referred to best-fit line (linear regression), unless otherwise noted.
Table 1.
Parameter
Conditions
Min
Typ
Max Unit
OVERALL FUNCTION
Maximum Input Frequency
RF INPUT INTERFACE
Input Impedance
Common Mode Voltage
100 MHz
Output Voltage: High Power in
Output Voltage: Low Power in
1.0 dB Dynamic Range
Maximum Input Level, 1.0 dB
Minimum Input Level, 1.0 dB
Deviation vs. Temperature
6
GHz
Pins INHI, INLO, ac-coupled
Single-ended drive
50/TBD
2.7
Ω/pF
V
Pin 16 - TCM1=0.47V, Pin 1 - TCM2= 1.0V
PIN = -10 dBm
PIN = -40 dBm
2.48
0.93
62
8
-54
V
V
dB
CW input, TA = +25°C
Deviation from output at 25°C
-40°C < TA < +85°C; PIN = -10 dBm
-40°C < TA < +85°C; PIN = -40 dBm
dB
dB
0.5
0.6
Logarithmic Slope
Logarithmic Intercept
Deviation from CW Response
51.8
-58
0.1
mV/dB
dBm
dB
13 dB peak-to-rms ratio (WCDMA), over 40 dB dynamic range
12 dB peak-to-rms ratio (WiMAX), over 40 dB dynamic range
0.1
dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 40 dB dynamic range
0.1
dB
256 QAM CF=8
0.1
dB
Input Impedance
Single-ended drive
TCM1= 0.48V, TCM2= 1.2V
PIN = -10 dBm
PIN = -40 dBm
CW input, TA = +25°C
50/TBD
Ω/pF
900 MHz
Output Voltage: High Power in
Output Voltage: Low Power in
1.0 dB Dynamic Range
2.5
0.91
52
V
V
dB
Maximum Input Level, 1.0 dB
Minimum Input Level, 1.0 dB
Deviation vs. Temperature
-2
-54
Deviation from output at 25°C
-40°C < TA < +85°C; PIN = -10 dBm
-40°C < TA < +85°C; PIN = -40 dBm
dB
0.5
0.7
dB
Logarithmic Slope
Logarithmic Intercept
Deviation from CW Response
51.9
-57.5
0.1
mV/dB
dBm
dB
13 dB peak-to-rms ratio (WCDMA), over 40 dB dynamic range
12 dB peak-to-rms ratio (WiMAX), over 40 dB dynamic range
0.1
dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 40 dB dynamic range
0.1
dB
256 QAM CF=8
0.1
dB
Input Impedance
Single-ended drive
TCM1=0.51V, TCM2= 0.51V
PIN = -10 dBm
PIN = -40 dBm
CW input, TA = +25°C
50/TBD
Ω/pF
1900 MHz
Output Voltage: High Power in
Output Voltage: Low Power in
1.0 dB Dynamic Range
2.38
0.8
42
V
V
dB
Maximum Input Level, 1.0 dB
Minimum Input Level, 1.0 dB
Deviation vs. Temperature
-10
-52
Deviation from output at 25°C
-40°C < TA < +85°C; PIN = -10 dBm
-40°C < TA < +85°C; PIN = -40 dBm
dB
0.5
0.6
dB
Logarithmic Slope
Logarithmic Intercept
Deviation from CW Response
52
-55
0.1
mV/dB
dBm
dB
13 dB peak-to-rms ratio (WCDMA), over 40 dB dynamic range
Rev. PrB| Page 2 of 14
Preliminary Technical Data
AD8363
Parameter
Conditions
Min
Typ
0.1
Max Unit
12 dB peak-to-rms ratio (WiMAX), over 40 dB dynamic range
dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 40 dB dynamic range
0.1
dB
256 QAM CF=8
0.1
dB
Input Impedance
Single-ended drive
TCM1=0.49V, TCM2=1.2V
PIN = -10 dBm
PIN = -40 dBm
CW input, TA = +25°C
50/TBD
Ω/pF
2140 MHz
Output Voltage: High Power in
Output Voltage: Low Power in
1.0 dB Dynamic Range
2.31
0.72
40
V
V
dB
Maximum Input Level, 1.0 dB
Minimum Input Level, 1.0 dB
Deviation vs. Temperature
-10
-50
Deviation from output at 25°C
-40°C < TA < +85°C; PIN = -10 dBm
-40°C < TA < +85°C; PIN = -40 dBm
dB
0.6
0.5
dB
Logarithmic Slope
Logarithmic Intercept
Deviation from CW Response
52.5
-53.5
0.1
mV/dB
dBm
dB
13 dB peak-to-rms ratio (WCDMA), over 40 dB dynamic range
12 dB peak-to-rms ratio (WiMAX), over 40 dB dynamic range
0.1
dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 40 dB dynamic range
0.1
dB
256 QAM CF=8
Single-ended drive
TCM1=, TCM2=
PIN = -10 dBm
PIN = -40 dBm
CW input, TA = +25°C,
0.1
50/TBD
dB
Ω/pF
Input Impedance
2600 MHz
Output Voltage: High Power in
Output Voltage: Low Power in
1.0 dB Dynamic Range
2.15
0.52
35
V
V
dB
Maximum Input Level, 1.0 dB
Minimum Input Level, 1.0 dB
Deviation vs. Temperature
-12
-40
Deviation from output at 25°C
-40°C < TA < +85°C; PIN = -10 dBm
-40°C < TA < +85°C; PIN = -40 dBm
TBD
TBD
53.2
-49.9
0.1
dB
dB
mV/dB
dBm
dB
Logarithmic Slope
Logarithmic Intercept
Deviation from CW Response
13 dB peak-to-rms ratio (WCDMA), over 40 dB dynamic range
12 dB peak-to-rms ratio (WiMAX), over 40 dB dynamic range
0.1
dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 40 dB dynamic range
0.1
dB
256 QAM CF=8
0.1
dB
Input Impedance
Single-ended drive
TCM1=0.56V, TCM2=1.0V
PIN = -15 dBm
PIN = -40 dBm
CW input, TA = +25°C,
50/TBD
Ω/pF
3.8 GHz
Output Voltage: High Power in
Output Voltage: Low Power in
1.0 dB Dynamic Range
2.0
0.5
33
V
V
dB
Maximum Input Level, 1.0 dB
Minimum Input Level, 1.0 dB
Deviation vs. Temperature
-16
-49
Deviation from output at 25°C
-40°C < TA < +85°C; PIN = -10 dBm
-40°C < TA < +85°C; PIN = -40 dBm
+/- 1.0
+/- 0.8
54.7
-50
0.1
0.1
dB
dB
mV/dB
dBm
dB
dB
dB
dB
Logarithmic Slope
Logarithmic Intercept
Deviation from CW Response
13 dB peak-to-rms ratio (WCDMA), over 40 dB dynamic range
12 dB peak-to-rms ratio (WiMAX), over 40 dB dynamic range
14.0 dB peak-to-rms ratio (16C CDMA2K), over 40 dB dynamic range
256 QAM CF=8
0.1
0.1
5.8 GHz
TCM1=0.88V, TCM2= 1.0V
Output Voltage: High Power in
Output Voltage: Low Power in
1.0 dB Dynamic Range
PIN = -20 dBm
PIN = -40 dBm
CW input, TA = +25°C
1.5
0.35
30
V
V
dB
Rev. PrB | Page 3 of 14
AD8363
Preliminary Technical Data
Parameter
Conditions
Min
Typ
-17
-47
Max Unit
Maximum Input Level, 1.0 dB
Minimum Input Level, 1.0 dB
Deviation vs. Temperature
Deviation from output at 25°C
-40°C < TA < +85°C; PIN = -10 dBm
-40°C < TA < +85°C; PIN = -40 dBm
dB
dB
0.6
0.7
54.5
Logarithmic Slope
mV/dB
Logarithmic Intercept
Deviation from CW Response
-47
0.1
0.1
0.1
0.1
dBm
dB
dB
dB
dB
13 dB peak-to-rms ratio (WCDMA), over 40 dB dynamic range
12 dB peak-to-rms ratio (WiMAX), over 40 dB dynamic range
14.0 dB peak-to-rms ratio (16C CDMA2K), over 40 dB dynamic range
256 QAM CF=8
OUTPUT INTERFACE
Output Swing
Pin 6 - VOUT
Voltage Range Min RL≥200 to ground
Voltage Range Max RL≥200 to ground
Source/Sink Current Out held at Vs/2K, to 1%change
Pin VSET
Log conformance error ≤1 dB, Min 2140 MHz
Log conformance error ≤1 dB, Max 2140 MHz
.09
Vs-.15
10
v
V
mA
SETPOINT INPUT
Voltage Range
TBD
TBD
72
V
Input Resistance
kΩ
Logarithmic Scale Factor
Logarithmic Intercept
TEMPERATURE COMPENSATION
Input Voltage Range
Input Resistance
f = 2140MHz, −40°C ≤ TA ≤ +85°C
f = 2140 MHz, −40°C ≤ TA ≤ +85°C, referred to 50 Ω
Pin 16 - TCM1, Pin 1 - TCM2
19
−TBD
dB/V
dBm
0
2.5
V
MΩ
3kΩ
TCM2
TCM1
>1
3
VOLTAGE REFERENCE
Output Voltage
Current Limit Source/Sink
TEMPERATURE REFERENCE
Output Voltage
Temperature Coefficient
POWER-DOWN INTERFACE
Logic Level to Enable
Logic Level to Disable
Input Current
Pin 11 - VREF
RF in = −55 dBm
1% change
2.3
5/0.08
V
mA
Pin 8 TEMP
TA = 25°C, RL ≥ 10 kΩ
−40°C ≤ TA ≤ +85°C, RL ≥ 10 kΩ
Pin TCM2 (Pin1)
Logic LO enables Max
Logic HI disables Min
Logic HI TCM2 = 5 V
Logic LO TCM2 = 0 V
1.35
4.8
V
mV/°C
< Vs -.9
Vs -.8
<1
<1
30
V
V
μA
μA
μs
Enable Time
Disable Time
TCM2 LO to OUT at .5 dB of final value,
CLPF = 470 pF, CHPF = 220 pF, RF in = 0 dBm
TCM2 HI to OUT at 10% final value,
20
μs
CLPF = 470 pF, CHPF = 220 pF, RF in = 0 dBm
POWER SUPPLY INTERFACE
Supply Voltage
Pin VPOS
4.5
5
5.5
V
Quiescent Current
25C RF in =-55 dBm
+85 C
When disabled
60
72
310
mA
mA
ꢀA
Supply Current
Rev. PrB| Page 4 of 14
Preliminary Technical Data
ABSOLUTE MAXIMUM RATINGS
AD8363
Table 2.
Parameter
Rating
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Supply Voltage VPOS
Input Power (Into Input of Device)
Equivalent Voltage
Internal Power Dissipation
θJA
Maximum Junction Temperature
Operating Temperature Range
Storage Temperature Range
Lead Temperature (Soldering 60 sec)
5.5 V
23 dBm Evaluate
2 V rms
500 mW
125°C/W
150°C
−40°C to +125°C
−65°C to +150°C
300°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. PrB | Page 5 of 14
AD8363
Preliminary Technical Data
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
12
11
10
9
VTGT VREF VPOS COMM
13 NCON
TEMP
VSET
VOUT
CLPF
8
14 INHI
7
6
5
AD8363
15 INLO
16 TCM1
TCM2 CHPF VPOS COMM
1
2
3
4
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin
No.
Mnemonic
Description
1
2
TCM2/PWDN
A dual function pin used for controlling the amount of nonlinear intercept temperature
compensation and/or shutting down the device. This pin can be connected to the
VREF pin through a voltage divider if the shut down function is not used
CHPF
Connect to VPOS via a capacitor to determine -3 dB point of the input signal high-pass
filter.
3, 10
4, 9
5
VPOS
COMM
CLPF
Supply for the device. Connect to +5 V power supply.
System Common Connection. Connect via low impedance to system common.
Connection for Loop Filter Integration (Averaging) Capacitor. Connect a ground-
referenced capacitor to this pin. A resistor may be connected in series with this
capacitor to improve loop stability and response time.
6
7
VOUT
VSET
Output pin in Measurement Mode (error Amplifier output). In measurement mode,
normally connected directly to VSET. This pin can be used to drive a gain control when
the device is used in controller mode.
The voltage applied to this pin sets the decibel value of the required RF input voltage
that results in zero current flow in the loop integrating capacitor pin, CLPF.
The controls the VGA gain such that a 50mV change in VSET reduces the gain by
approximately 1dB.
8
TEMP
VREF
VTGT
Temperature Sensor Output.
11
12
General-Purpose Reference Voltage Output of 1.16 V.
Voltage applied to this pin determines the target power at the input of the RF squaring
circuit. The intercept voltage is proportional to the voltage applied to this pin. The use
of a lower target voltage increases the crest factor capacity; however, this may affect
the system loop response.
13
14
NCON
INHI
Not connected.
Single-ended RF input pin. RF input signal is normally AC coupled to this pin through a
coupling capacitor.
15
16
INLO
Grounded for single ended input
TCM1
Connect to VREF through a voltage divider or an external DC source. Is used to adjust
Intercept temperature compensation (3K impedance)
Paddle
Connect via low impedance to system common
Rev. PrB| Page 6 of 14
Preliminary Technical Data
AD8363
TYPICAL PERFORMANCE CHARACTERISTICS
VS = 5 V, ZO = 50 Ω, Single ended input drive, VOUT tied to VSET, VTGT = 1.4V, CLPF= 3.9 nF, CHPF=2.7 nF, TA = +25°C (Black), –40°C
(Blue), +85°C (red)
4
3.6
3.2
2.8
2.4
2
2.5
3.0
2.0
1.5
1.0
0.5
0.0
1.6
1.2
0.8
0.4
0
-0.5
-1.5
-2.5
-1.0
-2.0
-3.0
-60
-50
-40
-30
-20
-10
0
10
-60
-50
-40
-30
-20
-10
0
10
Input Amplitude, INHI (dBm)
Input Amplitude, INHI (dBm)
Figure 3. VOUT Voltage and Log Conformance vs. Input Amplitude at 100 MHz,
Typical Device, TCM1 = 0.47 V, TCM2 = 1.0 V, Sine Wave, -40C, 25C, 85C
Figure 6. Distribution of VOUT Voltage and Error over Temperature After
Ambient Normalization vs. Input Amplitude for at Least 30Devices from
Multiple Lots, Frequency = 100 MHz, TCM1 = 0.47 V, TCM2 = 1.0 V, Sine Wave-
40C, 25C, 85C
3.0
4
3.6
3.2
2.8
2.4
2
2.5
2.0
1.5
1.0
0.5
0.0
1.6
1.2
0.8
0.4
0
-0.5
-1.5
-2.5
-1.0
-2.0
-3.0
-60
-50
-40
-30
-20
-10
0
10
-60
-50
-40
-30
-20
-10
0
10
Input Amplitude, INHI (dBm)
Input Amplitude, INHI (dBm)
Figure 7. Distribution of Error over Temperature After Ambient Normalization vs.
Input Amplitude, with reference to 25C, for at Least 30Devices from Multiple
Lots, Frequency = 100 MHz, TCM1 = 0.47 V, TCM2 = 1.0 V, Sine Wave-40C, 25C,
85C
Figure 4. VOUT Voltage and Log Conformance vs. Input Amplitude at 900 MHz,
Typical Device, TCM1 = 0.48 V, TCM2 = 1.2 V, Sine Wave -40C, 25C, 85C
3.0
2.0
3.0
2.0
1.0
1.0
0.0
0.0
-1.0
-2.0
-3.0
-1.0
-2.0
-3.0
-60
-50
-40
-30
-20
-10
0
10
-60
-50
-40
-30
-20
-10
0
10
Input Amplitude, INHI (dBm)
Input Amplitude, INHI (dBm)
Figure 5. Distribution of VOUT Voltage and Error over Temperature After
Ambient Normalization vs. Input Amplitude for at Least 30 Devices from
Multiple Lots, Frequency =900 MHz, TCM1 = 0.48 V, TCM2 = 1.2 V, Sine Wave-
40C, 25C, 85C
Figure 8. Distribution of Error over Temperature After Ambient Normalization vs.
Input Amplitude, with reference to 25C, for at Least 30Devices from Multiple
Lots,, Frequency =900 MHz, TCM1 = 0.48 V, TCM2 = 1.2 V, Sine Wave-40C, 25C,
85C
Rev. PrB | Page 7 of 14
AD8363
Preliminary Technical Data
3.0
3.0
2.0
2.0
1.0
1.0
0.0
0.0
-1.0
-2.0
-3.0
-1.0
-2.0
-3.0
-60
-50
-40
-30
-20
-10
0
-60
-50
-40
-30
-20
-10
0
Input Amplitude, INHI (dBm)
Input Amplitude, INHI (dBm)
Figure 12. Distribution of VOUT Voltage and Error over Temperature After
Ambient Normalization vs. Input Amplitude for at Least 18Devices from
Multiple Lots, Frequency = 1.9 GHz, TCM1 = 0.51 V, TCM2 = 0.51 V, Sine Wave-
40C, 25C, 85C
Figure 9. VOUT Voltage and Log Conformance vs. Input Amplitude at 1.90 GHz,
Typical Device, TCM1 = 0.51 V, TCM2 = 0.51 V, Sine Wave, -40C, 25C, 85C
3.0
2.0
3.0
2.0
1.0
1.0
0.0
0.0
-1.0
-2.0
-3.0
-1.0
-2.0
-3.0
-60
-50
-40
-30
-20
-10
0
-60
-50
-40
-30
-20
-10
0
10
Input Amplitude, INHI (dBm)
Input Amplitude, INHI (dBm)
Figure 13. Distribution of Error over Temperature After Ambient Normalization
vs. Input Amplitude, with reference to 25C, for at Least 18 Devices from Multiple
Lots, Frequency = 1.9 GHz, TCM1 = 0.51 V, TCM2 = 0.51 V, Sine Wave-40C, 25C,
85C
Figure 10. VOUT Voltage and Log Conformance vs. Input Amplitude at 2.14 GHz,
Typical Device, TCM1 = 0.49 V, TCM2 = 1.2 V, Sine Wave, -40C, 25C, 85C
3.0
2.0
3.0
2.0
1.0
1.0
0.0
0.0
-1.0
-2.0
-3.0
-1.0
-2.0
-3.0
-60
-50
-40
-30
-20
-10
0
10
-60
-50
-40
-30
-20
-10
0
10
Input Amplitude, INHI (dBm)
Input Amplitude, INHI (dBm)
Figure 14. Distribution of Error over Temperature After Ambient Normalization
vs. Input Amplitude, with reference to 25C, for at Least 18 Devices from Multiple
Lots, Frequency = 2.14 GHz, TCM1 = 0.49 V, TCM2 = 1.2 V, Sine Wave-40C, 25C,
85C
Figure 11. Distribution of VOUT Voltage and Error over Temperature After
Ambient Normalization vs. Input Amplitude for at Least 18Devices from
Multiple Lots, Frequency = 2.14 GHz, TCM1 = 0.49 V, TCM2 = 1.2 V, Sine Wave-
40C, 25C, 85C
Rev. PrB| Page 8 of 14
Preliminary Technical Data
AD8363
4
3.6
3.2
2.8
2.4
2
2.5
3.0
2.0
1.5
1.0
0.5
0.0
1.6
1.2
0.8
0.4
0
-0.5
-1.5
-2.5
-1.0
-2.0
-3.0
-55
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
5
-55
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
5
Input Amplitude, INHI (dBm)
Input Amplitude, INHI (dBm)
Figure 18. Distribution of VOUT Voltage and Error over Temperature After
Ambient Normalization vs. Input Amplitude for at Least 17 Devices from
Multiple Lots, Frequency = 2.6 GHz, TCM1 = 0.52 V, TCM2 = 1.1 V, Sine Wave-
40C, 25C, 85C
Figure 15. VOUT Voltage and Log Conformance vs. Input Amplitude at 2.6 GHz,
Typical Device, TADJ = TBD V, Sine Wave-40C, 25C, 85C
3.0
2.5
4
3.6
3.2
2.8
2.4
2
2.5
2.0
1.5
1.5
1.0
0.5
0.5
0.0
-0.5
-1.0
-1.5
-2.0
-2.5
-3.0
1.6
1.2
0.8
0.4
0
-0.5
-1.5
-2.5
-55
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
5
-55
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
Input Amplitude, INHI (dBm)
Input Amplitude, INHI (dBm)
Figure 19. Distribution of Error over Temperature After Ambient Normalization
vs. Input Amplitude, with reference to 25C, for at Least 17 Devices from Multiple
Lots, Frequency = 2.6 GHz, TCM1 = 0.52 V, TCM2 = 1.1 V, Sine Wave-40C, 25C,
85C
Figure 16. VOUT Voltage and Log Conformance vs. Input Amplitude at 3.8 GHz,
Typical Device, TCM1 = 0.56 V, TCM2 = 1.0 V, Sine Wave-40C, 25C, 85C
3.0
2.0
3.0
2.0
1.0
1.0
0.0
0.0
-1.0
-2.0
-3.0
-1.0
-2.0
-3.0
-55
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
-55
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
Input Amplitude, INHI (dBm)
Input Amplitude, INHI (dBm)
Figure 20. Distribution of Error over Temperature After Ambient Normalization
vs. Input Amplitude, with reference to 25C, for at Least 37 Devices from Multiple
Lots, Frequency = 3.8 GHz, TCM1 = 0.56 V, TCM2 = 1.0 V, Sine Wave-40C, 25C,
85C
Figure 17. Distribution of VOUT Voltage and Error over Temperature After
Ambient Normalization vs. Input Amplitude for at Least 37 Devices from
Multiple Lots, Frequency = 3.8 GHz, TCM1 = 0.56 V, TCM2 = 1.0 V, Sine Wave-
40C, 25C, 85C
Rev. PrB | Page 9 of 14
AD8363
Preliminary Technical Data
4
3.6
3.2
2.8
2.4
2
2.5
3.0
2.0
1.5
1.0
0.5
0.0
1.6
1.2
0.8
0.4
-0.5
-1.5
-2.5
-1.0
-2.0
-3.0
0
-55
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
-55
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
Input Amplitude, INHI (dBm)
Input Amplitude, INHI (dBm)
Figure 24. Distribution of VOUT Voltage and Error over Temperature After
Ambient Normalization vs. Input Amplitude for at Least 37 Devices from
Multiple Lots, Frequency = 5.8 GHz, TCM1 = 0.88 V, TCM2 = 1.0 V, Sine Wave-
40C, 25C, 85C
Figure 21. VOUT Voltage and Log Conformance vs. Input Amplitude at 5.8 GHz,
Typical Device, TCM1 = 0.88 V, TCM2 = 1.0 V, Sine Wave-40C, 25C, 85C
3
2.5
2
3.0
2.0
1.5
1
1.0
0.5
CW Error
0.0
0
-0.5
-1
Error 256 QAM
Error QPSK
-1.0
-2.0
-3.0
-1.5
-2
-2.5
-3
-55
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
-60
-50
-40
-30
-20
-10
0
10
Input Amplitude, INHI (dBm)
Pin (dBm)
Figure 25. Distribution of Error over Temperature After Ambient Normalization
vs. Input Amplitude, with reference to 25C, for at Least 37 Devices from Multiple
Lots, Frequency = 5.8 GHz, TCM1 = 0.88 V, TCM2 = 1.0 V, Sine Wave-40C, 25C,
85C
Figure 22. Error from CW Linear Reference vs. Input Amplitude with Different
Waveforms, 256 QAM, QPSK, Frequency 2140 MHz
3.50
3.00
2.50
2.00
1.50
1.00
0.50
0.00
-0.50
7.00
6.00
5.00
4.00
3.00
2.00
1.00
0.00
-1.00
8.00
5.00
TCM2 Low
TCM2 High
2.00
-1.00
-4.00
-7.00
-10.00
-13.00
-16.00
Time (in Seconds)
Time (in seconds)
P_INHI = 0dbm
P_INHI = -10dbm
P_INHI = -50dbm
P_INHI = -20dbm
Pulse on TCM2 (pin1)
P_INHI = -30dbm
P_INHI = -40dbm
P_INHI = 0dbm
P_INHI = -10dbm
P_INHI = -20dbm
P_INHI = -30dbm
P_INHI = -40dbm
Figure 23. Output Response to RF Burst Input for Various RF Input Levels, Carrier
Frequency 2.14 GHz, CLPF = 470 pF, CHPF=220pF
Figure 26. Output Response Using Power-Down Mode for Various RF Input
Levels, Carrier Frequency 2.14 GHz, CLPF= 470pF, CHPF = 220pF
Rev. PrB| Page 10 of 14
Preliminary Technical Data
AD8363
Table 4. Pin Function Descriptions
Component
Function/Notes
Default Value
C6, C10, C11,
C12
Input:
C10=0.1uF, C12=0.1uF,
C6=Open, C11=Open
The AD8363 was designed to be driven single ended. At frequencies below 2.6 GHz, more
dynamic range can be achieved by driving Pin 14 (INHI). In order to do this, C10 and C12
should be populated with an appropriate valued capacitor for the frequency of operation. C6
and C11 should be left open. For frequencies above 2.6 GHz, greater dynamic range can be
achieved by Driving Pin 15 (INLO). This can be done by using an appropriate valued capacitor
for C6 and C11, while leaving C10 and C12 open.
R7, R10, R11
VTGT:
R10=845Ω, R11= 1.4KΩ
R10 and R11 are set up to provide 1.4V to VTGT from VREF. An external voltage can be used if
R10 and R11 are removed.
C4, C5, C7, C13,
R14, R16
Power Supply Decoupling:
C4=100 pF, C5=100 pF,
C7= 0.1uF, C13= 0.1uF,
R14= 0 Ω, R16= 0 Ω
The nominal supply decoupling consists of a 100 pF filter capacitor placed physically close to
the AD8363, a 0 Ω series resistor, and a 0.1 uF capacitor placed closer to the power supply
input pin. The 0 Ω resistor can be replaced with a larger value resistor to add more filtering, at
the expense of a voltage drop.
R1, R2, R6, R13,
R15
Output Interface--Measurement Mode:
R1=0 Ω, R2=Open,
R6=0 Ω, R13 = Open ,
R15 = 0 Ω
In measurement mode, a portion of the output voltage is fed back to the VSET pin via R6. The
magnitude of the slope at VOUT can be increased by reducing the portion of VOUT that is fed
back to VSET, using a voltage divider created by R6 and R2 . If a fast responding output is
expected, the 0 Ω resistor on R15 can be removed to reduce parasitics on the output.
Output Interface--Controller Mode:
In this mode, R6 must be open and R13 must have a 0 Ω resistor. In controller mode, the
AD8363 can control the gain of an external component. A setpoint voltage is applied to the
VSET pin, the value of which corresponds to the desired RF input signal level applied to the
AD8363 RF input. If a fast responding output is expected, the 0 Ω resistor on R15 can be
removed to reduce parasitics on the output.
C9, C8, R5
C3
Low-pass filter capacitors:
C8=Open, C9=0.1uF,
R5=0 Ω
The low-pass filter capacitors reduce the noise on the output and affect the pulse response
time of the AD8363. The smallest CLPF capacitance should be 400 pF
CHPF capacitor
C3= 2700 pF
The CHPF capacitor introduces a high-pass filter effect into the AD8363 transfer function and
can affect the response time. It should be tied to VPOS.
R9, R12
R17, R18
Paddle
TCM2/PWDN:
R9= Open, R12= Open
The TCM2/PWDN pin controls the amount of nonlinear intercept temperature compensation
and/or shuts down the device. The evaluation board is configured to control this from a test
loop but VREF can be used through a voltage divider created from R9 and R12.
TCM1:
R17=Open, R18=Open
TCM1 controls the intercept temperature compensation (3K impedance). The evaluation board
is configured to control this from a test loop but VREF can be used through a voltage divider
created from R17 and R18
The paddle should be tied to both a thermal and electrical ground
Rev. PrB | Page 11 of 14
AD8363
Preliminary Technical Data
EVALUATION BOARD
VREF
VPOS2
TESTLOO
TESTLOO
P
P
ORANGE
RED
C7
0. 1UF
VTGT
C040
2
TESTLOO
P
AGND
C
ORANGE
VPOSC
R040
2
R7
0
R14
R8
0
0
R040
2
C5
R11
R10
R040
2
R040
2
R040 2
C040
2
1. 4K
845
VREFC
100PF
AGND
C
AGND C
AGND
C
R2
AGND
C
TESTLOO
P
OPEN
TEMP
VI OLET
R040
2
TESTLOO
P
12
11
10
9
VSET
WHI TE
VOUT
AGND
C
TESTLOO
P
R13
YELLOW
R040
2
C10
OPEN
0. 1UF
NC1
TEMP
VSET
VOUT
CLPF
R6
0
R15
0
I N
C040
2
R040
2
R040 2
16CSP4X4
I NHI
I NLO
TCM1
VOUTP
R1
AD83 63
C040
2
R040 2
TESTLOO
P
C6
OPEN
DUT1
0
ORANGE TC1
R17
C9
R040
2
0. 1uF
OPEN
C040
2
AGND
C
AGND C
1
2
3
4
R18
OPEN
Paddl e
AGND
AGND C
TC2_PWDN
R040
2
AGND
C
R5
0
C8
OPEN
TESTLOO
P
ORANGE
R040
2
VREFC
C3
C4
C040
2
C040
2
C040 2
AGND
C
AGND C
2700PF
100PF
R12
R9
AGND
C
OPEN
OPEN
R040
2
R040 2
GND
GND1
R16
0
TESTLOO
P
TESTLOO P
BLACK
BLACK
AGND
C
R040
2
VPOSC
C13
VREFC
C040
2
0. 1UF
AGND C
AGND
C
AGND C
RED
TESTLOO
P
VPOS1
Fig 27 Evaluation Board Schematic
Rev. PrB | Page 12 of 14
Preliminary Technical Data
AD8363
ASSEMBLY DRAWINGS
Fig 28 Evaluation Board Layout, Top
Fig 30 Evaluation Board Layout, Bottom
Fig 29 Evaluation Board Assembly, Top
Fig 31 Evaluation Board Assembly, Bottom
Rev. PrB | Page 13 of 14
AD8363
Preliminary Technical Data
OUTLINE DIMENSIONS
4.00
0.60 MAX
16
BSC SQ
PIN 1
INDICATOR
0.60 MAX
0.65 BSC
13
12
1
PIN 1
INDICATOR
2.25
2.10 SQ
1.95
TOP
VIEW
EXPOSED
3.75
BSC SQ
PAD
(BOTTOM VIEW)
0.75
0.60
0.50
4
9
8
5
0.25 MIN
1.95 BSC
0.80 MAX
0.65 TYP
12° MAX
0.05 MAX
0.02 NOM
1.00
0.85
0.80
0.30
0.23
0.18
0.20 REF
COPLANARITY
0.08
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VGGC
ORDERING GUIDE
Model
Temperature Range Package Description
Package Option Ordering Quantity
40°C to +125°C
1500
AD8363ACPZ-R7
16-Lead Lead Frame Chip Scale Package [LFCSP_VQ] CP-16-4
16-Lead Lead Frame Chip Scale Package [LFCSP_VQ] CP-16-4
16-Lead Lead Frame Chip Scale Package [LFCSP_VQ] CP-16-4
Evaluation Board
AD8363ACPZ-R2
40°C to +125°C
250
64
AD8363ACPZ-WP 40°C to +125°C
AD8363-EVALZ
Rev. A | Page 14 of 14
PR07368-0-8/08(PrB)
相关型号:
AD8364ACPZ-RL2
IC SPECIALTY ANALOG CIRCUIT, QCC32, 5 X 5 MM, LEAD FREE, MO-220VHHD-2, LFCSP-32, Analog IC:Other
ADI
©2020 ICPDF网 联系我们和版权申明