AD8038ARZ-REEL1 [ADI]
OP-AMP;型号: | AD8038ARZ-REEL1 |
厂家: | ADI |
描述: | OP-AMP |
文件: | 总16页 (文件大小:297K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Low Power, 350 MHz
Voltage Feedback Amplifiers
AD8038/AD8039
FEATURES
FUNCTIONAL BLOCK DIAGRAM
AD8038
Low power: 1 mA supply current/amp
High speed
350 MHz, −3 dB bandwidth (G = +1)
425 V/μs slew rate
NC
–IN
+IN
1
2
3
4
8
7
6
5
DISABLE
+V
S
V
OUT
–V
NC
S
NC = NO CONNECT
Low cost
Figure 1. 8-lead SOIC (R)
Low noise
8 nV/√Hz @ 100 kHz
600 fA/√Hz @ 100 kHz
Low input bias current: 750 nA maximum
Low distortion
−90 dB SFDR @ 1 MHz
AD8038
V
1
2
3
5
+V
S
OUT
–V
S
+IN
4
–IN
−65 dB SFDR @ 5 MHz
Figure 2. 5-Lead SC70 (KS)
Wide supply range: 3 V to 12 V
Small packaging: 8-lead SOT-23, 5-lead SC70, and 8-lead SOIC
AD8039
V
1
2
3
4
8
7
6
5
+V
OUT1
–IN1
S
APPLICATIONS
V
OUT2
Battery-powered instrumentation
Filters
+IN1
–IN2
+IN2
–V
S
A/D drivers
Level shifting
Buffering
NC = NO CONNECT
Figure 3. 8-Lead SOIC (R) and 8-Lead SOT-23 (RJ)
Photo multipliers
GENERAL DESCRIPTION
The AD8038 (single) and AD8039 (dual) amplifiers are high speed
(350 MHz) voltage feedback amplifiers with an exceptionally low
quiescent current of 1.0 mA/amplifier typical (1.5 mA maximum).
The AD8038 single amplifier in the 8-lead SOIC package has a
disable feature. Despite being low power and low cost, the amplifier
provides excellent overall performance. Additionally, it offers a
high slew rate of 425 V/μs and a low input offset voltage of 3 mV
maximum.
The AD8039 amplifier is available in a 8-lead SOT-23 package,
and the single AD8038 is available in both an 8-lead SOIC and a
5-lead SC70 package. These amplifiers are rated to work over
the industrial temperature range of −40°C to +85°C.
24
G = +10
21
18
15
12
G = +5
The Analog Devices, Inc., proprietary XFCB process allows low
noise operation (8 nV/√Hz and 600 fA/√Hz) at extremely low
quiescent currents. Given a wide supply voltage range (3 V to 12 V),
wide bandwidth, and small packaging, the AD8038 and AD8039
amplifiers are designed to work in a variety of applications
where power and space are at a premium.
9
6
3
G = +2
G = +1
0
–3
–6
The AD8038 and AD8039 amplifiers have a wide input common-
mode range of 1 V from either rail and swing to within 1 V of each
rail on the output. These amplifiers are optimized for driving
capacitive loads up to 15 pF. If driving larger capacitive loads, a small
series resistor is needed to avoid excessive peaking or overshoot.
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 4. Small Signal Frequency Response for Various Gains,
OUT = 500 mV p-p, VS = 5 V
V
Rev. G
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2002–2009 Analog Devices, Inc. All rights reserved.
AD8038/AD8039
TABLE OF CONTENTS
Features .............................................................................................. 1
Disable ......................................................................................... 13
Power Supply Bypassing............................................................ 13
Grounding................................................................................... 13
Input Capacitance ...................................................................... 13
Output Capacitance ................................................................... 13
Input-to-Output Coupling........................................................ 13
Applications Information.............................................................. 14
Low Power ADC Driver ............................................................ 14
Low Power Active Video Filter................................................. 14
Outline Dimensions....................................................................... 15
Ordering Guide .......................................................................... 16
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
Maximum Power Dissipation ..................................................... 5
Output Short Circuit.................................................................... 5
ESD Caution.................................................................................. 5
Typical Performance Characteristics ............................................. 6
Layout, Grounding, and Bypassing Considerations .................. 13
REVISION HISTORY
8/09—Rev. F to Rev. G
5/02—Rev. A to Rev. B
Changes to Applications Section and General Description
Section................................................................................................ 1
Changes to Disable Section and Grounding Section................. 13
Changes to Low Power ADC Driver Section and Low Power
Active Video Filter Section............................................................ 14
Updated Outline Dimensions....................................................... 15
Changes to Ordering Guide .......................................................... 16
Add Part Number AD8038 ...............................................Universal
Changes to Product Title..................................................................1
Changes to Features ..........................................................................1
Changes to Product Description .....................................................1
Changes to Connection Diagram....................................................1
Update to Specifications ...................................................................2
Update to Maximum Power Dissipation........................................4
Update to Output Short Circuit.......................................................4
Update to Ordering Guide ...............................................................4
Change to Figure 2 ............................................................................4
Change to TPC 2 ...............................................................................5
Change to TPC 18 .............................................................................6
Change to TPC 27 .............................................................................7
Change to TPC 29 .............................................................................8
Change to TPC 30 .............................................................................8
Change to TPC 31 .............................................................................8
Added TPC 36....................................................................................8
Added TPC 37....................................................................................9
Edits to Low Power Active Video Filter....................................... 10
Change to Figure 4 ......................................................................... 10
8/04—Rev. E to Rev. F
Changes to Figure 4........................................................................ 10
8/03—Rev. D to Rev. E
Change to TPC 34............................................................................. 8
7/03—Rev. C to Rev. D
Changes to Ordering Guide ............................................................ 4
Updated TPC 35 Caption ................................................................ 8
6/03—Rev. B to Rev. C
Updated Connection Diagrams...................................................... 1
Updated Ordering Guide................................................................. 4
Updated Outline Dimensions....................................................... 11
4/02—Rev. 0 to Rev. A
Changes to Features ..........................................................................1
Update Specifications................................................................... 2, 3
Edits to TPC 19..................................................................................7
Rev. G | Page 2 of 16
AD8038/AD8039
SPECIFICATIONS
TA = 25°C, VS = 5 V, RL = 2 kΩ, Gain = +1, unless otherwise noted.
Table 1.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
G = +1, VO = 0.5 V p-p
G = +2, VO = 0.5 V p-p
G = +1, VO = 2 V p-p
G = +2, VO = 0.2 V p-p
G = +1, VO = 2 V step, RL = 2 kΩ
G = +2, 1 V overdrive
G = +2, VO = 2 V step
300
350
175
100
45
425
50
MHz
MHz
MHz
MHz
V/μs
ns
Bandwidth for 0.1 dB Flatness
Slew Rate
Overdrive Recovery Time
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
SFDR
400
18
ns
Second Harmonic
Third Harmonic
Second Harmonic
Third Harmonic
Crosstalk, Output-to-Output (AD8039)
Input Voltage Noise
Input Current Noise
fC = 1 MHz, VO = 2 V p-p, RL = 2 kΩ
fC = 1 MHz, VO = 2 V p-p, RL = 2 kΩ
fC = 5 MHz, VO = 2 V p-p, RL = 2 kΩ
fC = 5 MHz, VO = 2 V p-p, RL = 2 kΩ
f = 5 MHz, G = +2
−90
−92
−65
−70
−70
8
dBc
dBc
dBc
dBc
dB
nV/√Hz
fA/√Hz
f = 100 kHz
f = 100 kHz
600
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
Input Bias Current Drift
Input Offset Current
Open-Loop Gain
0.5
4.5
400
3
25
70
3
mV
μV/°C
nA
nA/°C
nA
dB
750
VO = 2.5 V
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
DC Output Voltage Swing
Capacitive Load Drive
POWER SUPPLY
10
2
4
MΩ
pF
V
RL = 1 kΩ
VCM = 2.5 V
61
67
dB
RL = 2 kΩ, saturated output
30% overshoot, G = +2
4
20
V
pF
Operating Range
3.0
12
V
Quiescent Current per Amplifier
Power Supply Rejection Ratio
1.0
−77
−70
1.5
mA
dB
dB
−Supply
+Supply
−71
−64
POWER-DOWN DISABLE1
Turn-On Time
Turn-Off Time
Disable Voltage—Part is Off
Disable Voltage—Part is On
Disabled Quiescent Current
Disabled In/Out Isolation
180
700
+VS − 4.5
+VS − 2.5
0.2
ns
ns
V
V
mA
dB
f = 1 MHz
−60
1 Only available in AD8038 8-lead SOIC package.
Rev. G | Page 3 of 16
AD8038/AD8039
TA = 25°C, VS = 5 V, RL = 2 kΩ to VS/2, Gain = +1, unless otherwise noted.
Table 2.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
−3 dB Bandwidth
G = +1, VO = 0.2 V p-p
G = +2, VO = 0.2 V p-p
G = +1, VO = 2 V p-p
G = +2, VO = 0.2 V p-p
G = +1, VO = 2 V step, RL = 2 kΩ
G = +2, 1 V overdrive
G = +2, VO = 2 V step
275
300
150
30
45
365
50
MHz
MHz
MHz
MHz
V/μs
ns
Bandwidth for 0.1 dB Flatness
Slew Rate
Overdrive Recovery Time
Settling Time to 0.1%
NOISE/HARMONIC PERFORMANCE
SFDR
340
18
ns
Second Harmonic
Third Harmonic
Second Harmonic
Third Harmonic
Crosstalk, Output-to-Output
Input Voltage Noise
Input Current Noise
fC = 1 MHz, VO = 2 V p-p, RL = 2 kΩ
fC = 1 MHz, VO = 2 V p-p, RL = 2 kΩ
fC = 5 MHz, VO = 2 V p-p, RL = 2 kΩ
fC = 5 MHz, VO = 2 V p-p, RL = 2 kΩ
f = 5 MHz, G = +2
−82
−79
−60
−67
−70
8
dBc
dBc
dBc
dBc
dB
nV/√Hz
fA/√Hz
f = 100 kHz
f = 100 kHz
600
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
Input Bias Current Drift
Input Offset Current
0.8
3
400
3
30
70
3
mV
ꢀV/°C
nA
nA/°C
nA
dB
750
Open-Loop Gain
VO = 2.5 V
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
DC Output Voltage Swing
Capacitive Load Drive
POWER SUPPLY
10
2
1.0 − 4.0
65
MΩ
pF
V
RL = 1 kΩ
VCM = 1 V
59
dB
RL = 2 kΩ, saturated output
30% overshoot
0.9 − 4.1
20
V
pF
Operating Range
3
12
V
Quiescent Current per Amplifier
Power Supply Rejection Ratio
POWER-DOWN DISABLE1
Turn-On Time
0.9
−71
1.5
mA
dB
−65
210
700
+VS − 4.5
+VS − 2.5
0.2
ns
ns
V
V
mA
dB
Turn-Off Time
Disable Voltage—Part is Off
Disable Voltage—Part is On
Disabled Quiescent Current
Disabled In/Out Isolation
f = 1 MHz
−60
1 Only available in AD8038 8-lead SOIC package.
Rev. G | Page 4 of 16
AD8038/AD8039
ABSOLUTE MAXIMUM RATINGS
Table 3.
2.0
1.5
1.0
0.5
0
Parameter
Rating
Supply Voltage
12.6 V
SOIC-8
SOT-23-8
SC70-5
Power Dissipation
See Figure 5
VS
Common-Mode Input Voltage
Differential Input Voltage
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
4 V
−65°C to +125°C
−40°C to +85°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
–55
–25
5
35
65
95
125
AMBIENT TEMPERATURE (°C)
Figure 5. Maximum Power Dissipation vs. Temperature for a 4-Layer Board
RMS output voltages should be considered. If RL is referenced to
VS−, as in single-supply operation, then the total drive power is
VS × IOUT. If the rms signal levels are indeterminate, consider the
worst case, when VOUT = VS /4 for RL to midsupply
MAXIMUM POWER DISSIPATION
PD = (VS × IS) + (VS/4)2/RL
The maximum safe power dissipation in the AD8038/AD8039
package is limited by the associated rise in junction temperature
(TJ) on the die. The plastic encapsulating the die locally reaches
the junction temperature. At approximately 150°C, which is the
glass transition temperature, the plastic changes its properties.
Even temporarily exceeding this temperature limit may change
the stresses that the package exerts on the die, permanently
shifting the parametric performance of the AD8038/AD8039.
Exceeding a junction temperature of 175°C for an extended
time can result in changes in the silicon devices, potentially
causing failure.
In single-supply operation with RL referenced to VS−, worst case
is VOUT = VS /2.
Airflow increases heat dissipation, effectively reducing θJA. In
addition, more metal directly in contact with the package leads
from metal traces, throughholes, ground, and power planes reduce
the θJA. Care must be taken to minimize parasitic capacitances at
the input leads of high speed op amps as discussed in the
Layout, Grounding, and Bypassing Considerations section.
Figure 5 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the 8-lead SOIC
(125°C/W), 5-lead SC70 (210°C/W), and 8-lead SOT-23
(160°C/W) packages on a JEDEC standard 4-layer board.
The still-air thermal properties of the package and PCB (θJA),
ambient temperature (TA), and total power dissipated in the
package (PD) determine the junction temperature of the die.
The junction temperature can be calculated as
θ
JA values are approximations.
OUTPUT SHORT CIRCUIT
TJ = TA + (PD × θJA)
Shorting the output to ground or drawing excessive current
from the AD8038/AD8039 will likely cause a catastrophic failure.
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive for all outputs. The quiescent power
is the voltage between the supply pins (VS) multiplied by the
quiescent current (IS). Assuming the load (RL) is referenced to
midsupply, then the total drive power is VS/2 × IOUT, some of which
is dissipated in the package and some in the load (VOUT × IOUT).
The difference between the total drive power and the load
power is the drive power dissipated in the package.
ESD CAUTION
PD = quiescent power + (total drive power − load power)
PD = [VS × IS] + [(VS/2) × (VOUT/RL)] − [VOUT2/RL]
Rev. G | Page 5 of 16
AD8038/AD8039
TYPICAL PERFORMANCE CHARACTERISTICS
Default Conditions: 5 V, CL = 5 pF, G = +2, RG = RF = 1 kΩ, RL = 2 kΩ, VO = 2 V p-p, Frequency = 1 MHz, TA = 25°C.
24
21
18
15
12
9
7
6
5
4
3
2
1
0
G = +10
G = +5
R
= 2kΩ
L
R
= 500Ω
L
G = +2
G = +1
6
R
= 1kΩ
3
L
0
–3
–6
0.1
1
10
100
1000
0.1
1
10
FREQUENCY (MHz)
100
1000
FREQUENCY (MHz)
Figure 6. Small Signal Frequency Response for Various Gains,
VOUT = 500 mV p-p
Figure 9. Small Signal Frequency Response for Various RL,
VS = 5 V, VOUT = 500 mV p-p
7
8
7
6
5
4
3
2
1
0
V
= ±1.5V
S
R
= 2kΩ
L
6
5
4
3
2
1
0
V
= ±2.5V
S
V
= ±5V
S
R = 500Ω
L
R
= 1kΩ
L
0.1
1
10
FREQUENCY (MHz)
100
1000
0.1
1
10
100
FREQUENCY (MHz)
Figure 7. Small Signal Frequency Response for Various Supplies,
VOUT = 500 mV p-p
Figure 10. Large Signal Frequency Response for Various RL,
VOUT = 3 V p-p, VS = 5 V
7
6
8
R
= 2kΩ
L
7
6
5
4
3
2
1
0
R
= 2kΩ
L
5
4
3
2
1
0
R
= 500Ω
L
R
= 500Ω
L
R
= 1kΩ
L
R
= 1kΩ
L
0.1
1
10
FREQUENCY (MHz)
100
1000
0.1
1
10
FREQUENCY (MHz)
100
Figure 8. Small Signal Frequency Response for Various RL,
VS = 5 V, VOUT = 500 mV p-p
Figure 11. Large Signal Frequency Response for Various RL,
OUT = 4 V p-p, VS = 5 V
V
Rev. G | Page 6 of 16
AD8038/AD8039
5
4
80
70
60
50
40
30
20
10
0
180
135
90
C
= 15pF
= 10pF
L
3
C
L
2
PHASE
1
0
GAIN
45
–1
–2
–3
–4
–5
C
= 5pF
L
0
–10
–20
–45
1000
0.01
0.1
1
10
100
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 15. Open-Loop Gain and Phase, VS = 5 V
Figure 12. Small Signal Frequency Response for Various CL,
VOUT = 500 mV p-p, VS = 5 V, G = +1
9
6
7
5
C
= 15pF
L
–40°C
+25°C
3
C
= 10pF
L
3
1
+85°C
–1
–3
–5
C
= 5pF
L
0
–3
0.1
1
10
100
1000
1
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 16. Frequency Response vs. Temperature,
Gain = +2, VS = 5 V, VOUT = 2 V p-p
Figure 13. Small Signal Frequency Response for Various CL,
VOUT = 500 mV p-p, VS = 5 V, G = +1
–50
–55
–60
–65
–70
–75
–80
–85
–90
2
R
= 500Ω HD2
V
= 200mV
L
OUT
1
0
V
= 1V
OUT
R
= 500Ω HD3
L
–1
–2
–3
–4
–5
–6
V
= 500mV
= 2V
OUT
R
= 2kΩ HD3
L
R
= 2kΩ HD2
L
V
OUT
1
2
3
4
5
6
7
8
9
10
0.1
1
10
FREQUENCY (MHz)
100
1000
FREQUENCY (MHz)
Figure 17. Harmonic Distortion vs. Frequency for Various Loads,
VS = 5 V, VOUT = 2 V p-p, G = +2
Figure 14. Frequency Response for Various Output Voltage Levels
Rev. G | Page 7 of 16
AD8038/AD8039
–40
–50
–60
–70
–80
–90
–100
–45
–50
10MHz HD2
R
= 500Ω HD2
L
–55
–60
–65
–70
–75
–80
–85
–90
5MHz HD2
5MHz HD3
R
= 500Ω HD3
10MHz HD3
L
R
= 2kΩ HD3
1MHz HD3
L
R
3
= 2kΩ HD2
1MHz HD2
L
1
2
4
5
6
7
8
9
10
1
2
3
4
FREQUENCY (MHz)
AMPLITUDE (V p-p)
Figure 18. Harmonic Distortion vs. Frequency for Various Loads,
VS = 5 V, VOUT = 2 V p-p, G = +2
Figure 21. Harmonic Distortion vs. VOUT Amplitude for Various Frequencies,
VS = 5 V, G = +2
–45
–50
10MHz HD2
G = +1 HD2
–60
–55
10MHz HD3
G = +2 HD2
5MHz HD2
–65
–70
5MHz HD3
G = +2 HD3
–75
–80
1MHz HD3
G = +1 HD3
1MHz HD2
–85
–90
–100
–95
1.0
1
2
3
4
5
6
7
8
9
10
1.5
2.0
2.5
3.0
FREQUENCY (MHz)
AMPLITUDE (V p-p)
Figure 19. Harmonic Distortion vs. Frequency for Various Gains,
VS = 5 V, VOUT = 2 V p-p
Figure 22. Harmonic Distortion vs. Amplitude for Various Frequencies,
VS = 5 V, G = +2
1000
100
10
–50
G = +1 HD2
–60
G = +2 HD2
–70
G = +2 HD3
–80
G = +1 HD3
–90
1
10
100
1k
10k
100k
1M
10M
100M
–100
1
2
3
4
5
6
7
8
9
10
FREQUENCY (Hz)
)
Hz
Y (M
ENC
QU
FRE
Figure 23. Input Voltage Noise vs. Frequency
Figure 20. Harmonic Distortion vs. Frequency for Various Gains,
VS = 5 V, VOUT = 2 V p-p
Rev. G | Page 8 of 16
AD8038/AD8039
100k
10k
1k
C
R
= 25pF WITH
SNUB
L
= 19.6Ω
C
= 5pF
L
C
= 10pF
L
50mV/DIV
5ns/DIV
100
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 27. Small Signal Transient Response for Various CL, VS = 5 V
Figure 24. Input Current Noise vs. Frequency
R
= 500Ω
C
R
= 25pF WITH
SNUB
L
R
= 2kΩ
L
L
= 19.6Ω
C
= 5pF
L
C
= 10pF
L
50mV/DIV
5ns/DIV
50mV/DIV
5ns/DIV
Figure 25. Small Signal Transient Response for Various RL, VS = 5 V
Figure 28. Small Signal Transient Response for Various CL, VS = 5 V
R = 2kΩ
L
R
= 500Ω
L
R
= 500Ω
L
R
= 2kΩ
L
2.5V
50mV/DIV
5ns/DIV
500mV/DIV
5ns/DIV
Figure 26. Small Signal Transient Response for Various RL, VS = 5 V
Figure 29. Large Signal Transient Response for Various RL, VS = 5 V
Rev. G | Page 9 of 16
AD8038/AD8039
IN
R
= 2kΩ
L
R
= 500Ω
L
OUT
1V/DIV
5ns/DIV
2V/DIV
50ns/DIV
Figure 33. Input Overdrive Recovery, Gain = +1
Figure 30. Large Signal Transient Response for Various RL, VS = 5 V
C
= 25pF
L
IN
OUT
C
= 5pF
L
2.5V
INPUT 1V/DIV
OUTPUT 2V/DIV
500mV/DIV
5ns/DIV
50ns/DIV
Figure 31. Large Signal Transient Response for Various CL, VS = 5 V
Figure 34. Output Overdrive Recovery, Gain = +2
C
= 10pF
V = ±5V
S
G = +2
2mV/DIV
L
V
= 2V p-p
OUT
C
= 5pF
L
ERROR
VOLTAGE
+0.1%
0
t = 0
–0.1%
V
IN
500mV/DIV
5ns/DIV
0.5V/DIV
5ns/DIV
Figure 35. 0.1% Settling Time VOUT = 2 V p-p
Figure 32. Large Signal Transient Response for Various CL, VS = 5 V
Rev. G | Page 10 of 16
AD8038/AD8039
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
10
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–PSRR
SIDE B
+PSRR
SIDE A
0.1
1
10
FREQUENCY (MHz)
100
1000
0.01
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 36. AD8039 Crosstalk, VIN = 1 V p-p, Gain = +1
Figure 39. PSRR vs. Frequency
9
8
7
6
5
4
3
2
1
0
–10
–20
–30
–40
–50
–60
–70
–80
V
= ±5V
S
V
= +5V
V = ±5V
S
S
V
= +5V
S
0
100
200
300
(Ω)
400
500
1
10
100
1000
R
LOAD
FREQUENCY (MHz)
Figure 40. Output Swing vs. Load Resistance
Figure 37. CMRR vs. Frequency, VIN = 1 V p-p
1.25
1.00
0.75
0.50
0.25
0
1000
100
10
1
V
= ±5V
S
V
= +5V
S
0.1
0.01
0
2
4
6
8
10
12
0.1
1
10
100
1000
SUPPLY VOLTAGE (V)
FREQUENCY (MHz)
Figure 41. AD8038 Supply Current vs. Supply Voltage
Figure 38. Output Impedance vs. Frequency
Rev. G | Page 11 of 16
AD8038/AD8039
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 42. AD8038 Input-Output Isolation (G = +2, RL = 2 kΩ, VS = 5 V)
Rev. G | Page 12 of 16
AD8038/AD8039
LAYOUT, GROUNDING, AND BYPASSING CONSIDERATIONS
DISABLE
INPUT CAPACITANCE
The AD8038 in the 8-lead SOIC package provides a disable
feature. This feature disables the input from the output (see
Figure 42 for input-output isolation) and reduces the quiescent
Along with bypassing and ground, high speed amplifiers can be
sensitive to parasitic capacitance between the inputs and ground. A
few picofarads of capacitance reduces the input impedance at
high frequencies, in turn increasing the gain of the amplifiers,
causing peaking of the frequency response, or even oscillations
if severe enough. It is recommended that the external passive
components that are connected to the input pins be placed as
close as possible to the inputs to avoid parasitic capacitance.
The ground and power planes must be kept at a distance of at
least 0.05 mm from the input pins on all layers of the board.
DISABLE
current from typically 1 mA to 0.2 mA. When the
node is pulled below 4.5 V from the positive supply rail, the part
DISABLE
becomes disabled. To enable the part, the
to be pulled to greater than (VS – 2.5).
node needs
POWER SUPPLY BYPASSING
Power supply pins are actually inputs, and care must be taken
so that a noise-free stable dc voltage is applied. The purpose of
bypass capacitors is to create low impedances from the supply
to ground at all frequencies, thereby shunting or filtering a
majority of the noise.
OUTPUT CAPACITANCE
To a lesser extent, parasitic capacitances on the output can cause
peaking of the frequency response. Two methods to minimize
this effect include the following:
Decoupling schemes are designed to minimize the bypassing
impedance at all frequencies with a parallel combination of
capacitors. The 0.01 μF or 0.001 ꢀF (X7R or NPO) chip capacitors
are critical and should be placed as close as possible to the
amplifier package. Larger chip capacitors, such as 0.1 ꢀF
capacitors, can be shared among a few closely spaced active
components in the same signal path. A 10 ꢀF tantalum capacitor
is less critical for high frequency bypassing and, in most cases,
only one per board is needed at the supply inputs.
•
Put a small value resistor in series with the output to isolate
the load capacitor from the output stage of the amplifier, see
Figure 12, Figure 13, Figure 27, and Figure 28.
Increase the phase margin with higher noise gains or add
a pole with a parallel resistor and capacitor from −IN to
the output.
•
INPUT-TO-OUTPUT COUPLING
The input and output signal traces should not be parallel to
minimize capacitive coupling between the inputs and outputs,
avoiding any positive feedback.
GROUNDING
A ground plane layer is important in densely packed PC boards
to spread the current minimizing parasitic inductances. However,
an understanding of where the current flows in a circuit is critical
to implementing effective high speed circuit design. The length
of the current path is directly proportional to the magnitude of
parasitic inductances and, therefore, the high frequency impedance
of the path. High speed currents in an inductive ground return
create an unwanted voltage noise.
The length of the high frequency bypass capacitor leads is most
critical. A parasitic inductance in the bypass grounding works
against the low impedance created by the bypass capacitor. Because
load currents flow from the supplies as well, the ground for the
load impedance should be at the same physical location as the
bypass capacitor grounds. For the larger value capacitors, which
are intended to be effective at lower frequencies, the current
return path distance is less critical.
Rev. G | Page 13 of 16
AD8038/AD8039
APPLICATIONS INFORMATION
LOW POWER ADC DRIVER
LOW POWER ACTIVE VIDEO FILTER
1kΩ
2.5V
Some composite video signals derived from a digital source
contain clock feedthrough that can limit picture quality. Active
filters made from op amps can be used in this application, but
they consume 25 mW to 30 mW for each channel. In power-
sensitive applications, this can be too much, requiring the use
of passive filters that can create impedance matching problems
when driving any significant load.
+5V
0.1µF
10µF
3V
0.1µF
10µF
8
1kΩ
1kΩ
1kΩ
REF
VINP
3
2
50Ω
1
V
IN
0V
1kΩ
1kΩ
AD9203
AD8039
The AD8038 can be used to make an effective low-pass active
filter that consumes one-fifth of the power consumed by an
active filter made from an op amp. Figure 44 shows a circuit
that uses a AD8038 with 2.5 V supplies to create a three-pole
Sallen-Key filter. This circuit uses a single RC pole in front of a
standard 2-pole active section.
6
5
50Ω
7
VINN
4
1kΩ
10µF
0.1µF
–5V
1kΩ
R
1Ω
F
680pF
Figure 43. Schematic to Drive AD9203 with the AD8039
+2.5V
The AD9203 is a low power (125 mW on a 5 V supply), 40 MSPS
10-bit converter. As such, the low power, high performance
AD8039 is an appropriate amplifier choice to drive it.
10µF
0.1µF
R1
R2
R3
V
AD8038
OUT
200Ω
499Ω 49.9Ω
R5
75Ω
V
IN
In low supply voltage applications, differential analog inputs
are needed to increase the dynamic range of the ADC inputs.
Differential driving can also reduce second and other even-order
distortion products. The AD8039 can be used to make a dc-
coupled, single-ended-to-differential driver for driving these
ADCs. Figure 43 is a schematic of such a circuit for driving the
AD9203, 10-bit, 40 MSPS ADC.
R4
49.9Ω
C1
100pF
C3
33pF
10µF
0.1µF
–2.5V
Figure 44. Low-Pass Filter for Video
Figure 45 shows the frequency response of this filter. The
response is down 3 dB at 6 MHz; therefore, it passes the video
band with little attenuation. The rejection at 27 MHz is 45 dB,
which provides more than a factor of 100 in suppression of the
clock components at this frequency.
The AD9203 works best when the common-mode voltage at the
input is at the midsupply or 2.5 V. The output stage design of
the AD8039 makes it ideal for driving these types of ADCs.
10
In this circuit, one of the op amps is configured in the inverting
mode, and the other is in the noninverting mode. However, to
provide better bandwidth matching, each op amp is configured
for a noise gain of +2. The inverting op amp is configured for a
gain of −1, and the noninverting op amp is configured for a gain
of +2. Each has a very similar ac response. The input signal to
the noninverting op amp is divided by 2 to normalize its voltage
level and make it equal to the inverting output.
0
–10
–20
–30
–40
–50
–60
The outputs of the op amps are centered at 2.5 V, which is the
midsupply level of the ADC. This is accomplished by first taking
the 2.5 V reference output of the ADC and dividing it by 2 with
a pair of 1 kꢁ resistors. The resulting 1.25 V is applied to the
positive input of each op amp. This voltage is then multiplied by
the gain of the op amps to provide a 2.5 V level at each output.
0.1
1
10
100
FREQUENCY (MHz)
Figure 45. Video Filter Response
Rev. G | Page 14 of 16
AD8038/AD8039
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
8
1
5
4
6.20 (0.2441)
5.80 (0.2284)
4.00 (0.1574)
3.80 (0.1497)
0.50 (0.0196)
0.25 (0.0099)
1.27 (0.0500)
BSC
45°
1.75 (0.0688)
1.35 (0.0532)
0.25 (0.0098)
0.10 (0.0040)
8°
0°
0.51 (0.0201)
0.31 (0.0122)
COPLANARITY
0.10
1.27 (0.0500)
0.40 (0.0157)
0.25 (0.0098)
0.17 (0.0067)
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 46. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
2.20
2.00
1.80
1.35
1.25
1.15
2.40
2.10
1.80
5
1
4
3
2
PIN 1
1.00
0.90
0.70
0.65 BSC
0.40
0.10
1.10
0.80
0.46
0.36
0.26
0.30
0.15
0.22
0.08
0.10 M
AX
SEATING
PLANE
0.10 COPLANARITY
COMPLIANT TO JEDEC STANDARDS MO-203-AA
Figure 47. 5-Lead Thin Shrink Small Outline Transistor Package [SC70]
(KS-5)
Dimensions shown in millimeters
Rev. G | Page 15 of 16
AD8038/AD8039
3.00
2.90
2.80
8
1
7
6
3
5
4
3.00
2.80
2.60
1.70
1.60
1.50
2
PIN 1
INDICATOR
0.65 BSC
1.95
BSC
1.30
1.15
0.90
0.22 MAX
0.08 MIN
1.45 MAX
0.95 MIN
0.60
0.45
0.30
0.15 MAX
0.05 MIN
8°
4°
0°
SEATING
PLANE
0.60
BSC
0.38 MAX
0.22 MIN
COMPLIANT TO JEDEC STANDARDS MO-178-BA
Figure 48. 8-Lead Small Outline Transistor Package [SOT-23]
(RJ-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range Package Description
Package Option Branding
AD8038AR
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
8-Lead Standard Small Outline Package [SOIC_N]
R-8
R-8
R-8
R-8
R-8
R-8
AD8038AR-REEL
AD8038AR-REEL7
AD8038ARZ1
AD8038ARZ-REEL1
AD8038ARZ-REEL71
AD8038AKSZ-R21
AD8038AKSZ-REEL1
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Standard Small Outline Package [SOIC_N]
5-Lead Thin Shrink Small Outline Transistor Package [SC70] KS-5
5-Lead Thin Shrink Small Outline Transistor Package [SC70] KS-5
5-Lead Thin Shrink Small Outline Transistor Package [SC70] KS-5
H1C
H1C
H1C
AD8038AKSZ-REEL71 −40°C to +85°C
AD8039AR
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Standard Small Outline Package [SOIC_N]
8-Lead Small Outline Transistor Package [SOT-23]
8-Lead Small Outline Transistor Package [SOT-23]
8-Lead Small Outline Transistor Package [SOT-23]
8-Lead Small Outline Transistor Package [SOT-23]
8-Lead Small Outline Transistor Package [SOT-23]
8-Lead Small Outline Transistor Package [SOT-23]
R-8
R-8
R-8
R-8
R-8
R-8
RJ-8
RJ-8
RJ-8
RJ-8
RJ-8
RJ-8
AD8039AR-REEL
AD8039AR-REEL7
AD8039ARZ1
AD8039ARZ-REEL1
AD8039ARZ-REEL71
AD8039ART-R2
AD8039ART-REEL
AD8039ART-REEL7
AD8039ARTZ-R21
AD8039ARTZ-REEL1
HYA
HYA
HYA
HYA#
HYA#
HYA#
AD8039ARTZ-REEL71 −40°C to +85°C
1 Z = RoHS Compliant Part, # denotes RoHS compliant part may be top or bottom marked..
©2002–2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D02951-0-8/09(G)
Rev. G | Page 16 of 16
相关型号:
©2020 ICPDF网 联系我们和版权申明