AD7280AWBSTZ [ADI]
Lithium Ion Battery Monitoring System Cell balancing interface; 锂离子电池监控系统电池平衡接口型号: | AD7280AWBSTZ |
厂家: | ADI |
描述: | Lithium Ion Battery Monitoring System Cell balancing interface |
文件: | 总48页 (文件大小:869K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Lithium Ion Battery Monitoring System
AD7280A
FUNCTIONAL BLOCK DIAGRAM
FEATURES
12-bit ADC, 1 μs per channel conversion time
6 analog input channels, common-mode
range 0.5 V to 27.5 V
V
DD
6 auxiliary ADC inputs
1.6 mV cell voltage accuracy
On-chip voltage regulator
Cell balancing interface
Daisy-chain interface
Internal reference: 3 ppm/oC
1.8 μA power-down current
DAISY-CHAIN
INTERFACE
CELL
BALANCING
INTERFACE
VIN6
VIN5
VIN4
VIN3
VIN2
VIN1
VIN0
HV
MUX
V
REGULATOR
12-BIT ADC
AD7280A
REG
DGND
DV
AV
CC
CC
AUX6
AUX5
AUX4
AUX3
AUX2
AUX1
High input impedance
V
DRIVE
LV
MUX
Serial interface with alert function
1 SPI interface for up to 48 channels
CRC protection on read and write commands
On-chip registers for channel sequencing
CONTROL LOGIC
AND SELF-TEST
CLOCK
SCLK
SDI
SDO
ALERT
CS
PD
AUX
TERM
LIMIT REG
SQN LOGIC
DATA MEMORY
SPI INTERFACE
V
C
REF
REF
2.5V
REF
VDD operating range: 8 V to 30 V
Temperature range: −40°C to +105°C
48-lead LQFP
REFGND
CNVST
MASTER
Qualified for automotive applications
APPLICATIONS
V
AGND
SDOlo ALERTlo
SS
Lithium ion battery monitoring
Electric and hybrid electric vehicles
Power supply backup
Figure 1.
Power tools
GENERAL DESCRIPTION
The AD7280A1 contains all the functions required for general-
purpose monitoring of stacked lithium ion batteries as used in
hybrid electric vehicles, battery backup applications, and power
tools. The part has multiplexed cell voltage and auxiliary ADC
measurement channels for up to six cells of battery management.
An internal 3 ppm/°C reference is provided that allows a cell
voltage accuracy of 1.ꢀ mꢁ. The ADC resolution is 12 bits and
allows conversion of up to 48 cells within 7 μs.
The AD7280A includes on-chip registers that allow a sequence
of channel measurements to be programmed to suit the application
requirements.
The AD7280A also includes a dynamic alert function that can
detect whether the cell voltages or auxiliary ADC inputs exceed
an upper or lower limit defined by the user. The AD7280A has
cell balancing interface outputs designed to control external FET
transistors to allow discharging of individual cells.
The AD7280A operates from a single ꢁDD supply that has a
range of 8 ꢁ to 30 ꢁ (with an absolute maximum rating of
33 ꢁ). The part provides six differential analog input channels
to accommodate large common-mode signals across the full
The AD7280A includes a built-in self-test feature that internally
applies a known voltage to the ADC inputs.
A daisy-chain interface allows up to eight parts to be stacked
without the need for individual device isolation.
ꢁDD range. Each channel allows an input signal range, ꢁIN(+)
The AD7280A requires only one supply pin that accepts ꢀ.9 mA
under normal operation while converting at 1 MSPS.
− ꢁIN(−), of 1 ꢁ to 5 ꢁ. The input pins assume a series stack of
six cells. In addition, the part includes six auxiliary ADC input
channels that can be used for temperature measurement or
system diagnostics.
All this functionality is provided in a 48-lead LQFP package
operating over a temperature range of −40°C to +105°C.
1 Patents pending.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2011 Analog Devices, Inc. All rights reserved.
AD7280A
TABLE OF CONTENTS
Features .............................................................................................. 1
Register Map ................................................................................... 28
Cell Voltage Registers ................................................................ 28
Auxiliary ADC Registers........................................................... 28
Self-Test Register ........................................................................ 28
Control Register ......................................................................... 28
Cell Overvoltage Register.......................................................... 29
Cell Undervoltage Register ....................................................... 30
AUX ADC Overvoltage Register.............................................. 30
AUX ADC Undervoltage Register ........................................... 30
Alert Register .............................................................................. 30
Cell Balance Register ................................................................. 30
CBx Timer Registers .................................................................. 30
PD Timer Register...................................................................... 31
Read Register .............................................................................. 31
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Power Specifications .................................................................... 5
Timing Specifications .................................................................. 6
Absolute Maximum Ratings............................................................ 7
Thermal Resistance ...................................................................... 7
ESD Caution.................................................................................. 7
Pin Configuration and Function Descriptions............................. 8
Typical Performance Characteristics ........................................... 11
Terminology .................................................................................... 14
Theory of Operation ...................................................................... 15
Circuit Information.................................................................... 15
Converter Operation.................................................................. 15
Analog Input Structure.............................................................. 16
Transfer Function....................................................................... 16
Typical Connection Diagrams.................................................. 17
Reference ..................................................................................... 19
Converting Cell Voltages and Auxiliary ADC Inputs ........... 19
CNVST
Control Register........................................................... 31
Serial Interface ................................................................................ 32
Writing to the AD7280A........................................................... 32
Reading from the AD7280A..................................................... 33
Daisy-Chain Interface.................................................................... 34
Addressing the AD7280A While Reading Back Conversion
or Register Data.......................................................................... 34
Initializing the AD7280A.......................................................... 34
Write Acknowledge.................................................................... 35
Cyclic Redundancy Check ........................................................ 35
Examples of Interfacing with the AD7280A............................... 38
Convert and Readback Routine ............................................... 38
Examples...................................................................................... 38
EMC Guidelines ............................................................................. 44
Schematic and Layout Guidelines............................................ 44
Operation in a Noisy Environment ......................................... 44
Software Flowchart .................................................................... 45
Outline Dimensions....................................................................... 46
Ordering Guide .......................................................................... 46
Automotive Products................................................................. 46
Converting Cell Voltages and Auxiliary ADC Inputs
in a Chain of AD7280As............................................................ 21
Conversion Window .................................................................. 22
Self-Test Conversion .................................................................. 22
Connection of Fewer Than Six Voltage Cells............................. 22
Auxiliary ADC Inputs................................................................ 23
Power Requirements .................................................................. 23
Power-Down ............................................................................... 24
Power-Up Time........................................................................... 25
Cell Balancing Outputs.............................................................. 25
Alert Output................................................................................ 27
REVISION HISTORY
4/11—Revision 0: Initial Version
Rev. 0 | Page 2 of 48
AD7280A
SPECIFICATIONS
VDD = 8 V to 30 V, VSS = 0 V, DVCC = AVCC = VREG, VDRIVE = 2.7 V to 5.5 V, TA = −40°C to +105°C, unless otherwise noted.
Table 1.
Parameter
DC ACCURACY (VIN0 TO VIN6)1
Min
Typ
Max
Unit
Test Conditions/Comments
Resolution
12
Bits
LSB
LSB
LSB
LSB
LSB
LSB
mV
mV
mV
mV
No missing codes
Integral Nonlinearity
Differential Nonlinearity
Offset Error
Offset Error Match
Gain Error
Gain Error Match
ADC Unadjusted Error2, 3
Total Unadjusted Error4, 5
±1
±0.8
±1
1
±1
1
±1.2
±±
±10
±14.5
VIN range6 = 1 V to 4.1 V, −10°C to +85°C
VIN range6 = 1 V to 4.1 V, −40°C to +85°C
VIN range6 = 1 V to 4.1 V, −40°C to +105°C
±1.6
CELL VOLTAGE INPUTS (VIN0 TO VIN6)
Pseudo Differential Input Voltage
VIN(x) − VIN(x − 1)
Absolute Input Voltage
Common-Mode Input Voltage
Static Leakage Current7
Dynamic Leakage Current7
Input Capacitance
1
2 × VREF
VCM + VREF
27.5
±70
±3
V
V
V
nA
nA
pF
VCM − VREF
0.5
±5
15
CNVST pulse every 100 ms
No missing codes
DC ACCURACY (AUX1 TO AUX6)1, 8
Resolution
Integral Nonlinearity
Differential Nonlinearity
Offset Error
Offset Error Match
Gain Error
Gain Error Match
ADC Unadjusted Error±
Total Unadjusted Error10
12
Bits
LSB
LSB
LSB
LSB
LSB
LSB
mV
mV
mV
±1
±0.8
±2
2
±2
2
±1.2
±20
±22
−40°C to +85°C
−40°C to +105°C
±1.6
AUXILIARY ADC INPUTS (AUX1 TO AUX6)
Input Voltage Range
Static Leakage Current7
Dynamic Leakage Current7
Input Capacitance
0
2 × VREF
±3
V
±15
15
nA
nA
pF
CNVST pulse every 100 ms
REFERENCE
Reference Voltage
2.4±4
2.4±4
2.5
2.5
±3
2.506
2.50±
±15
V
V
−40°C to +85°C
−40°C to +105°C
−40°C to +85°C
Reference Voltage Temperature
Coefficient
ppm/°C
±11
50
150
ppm/°C
ppm
ppm/1000
hours
−40°C to +105°C
−40°C to +105°C
Output Voltage Hysteresis
Long-Term Drift
Line Regulation
Turn-On Settling Time11, 12
±5
5.5
ppm/V
ms
10
VREG = 1 μF, VREF = 1 μF, CREF = 100 nF
Rev. 0 | Page 3 of 48
AD7280A
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
REGULATOR OUTPUT (VREG
)
Input Voltage Range
Output Voltage, VREG
Output Current14
Line Regulation
Load Regulation
Internal Short Protection Limit
CELL BALANCING OUTPUTS15
Output High Voltage, VOH
Output Low Voltage, VOL
CB1 Output Ramp-Up Time16
CB1 Output Ramp-Down Time17
CB2 to CB6 Output Ramp-Up Time16
CB2 to CB6 Output Ramp-Down Time17
LOGIC INPUTS
8
4.±
30
5.5
5
V
V
13
5.2
5 mA external load
mA
mV/V
mV/mA
mA
0.5
2.5
25
For a 10 Ω short
ISOURCE = 415 nA
VREG − 1
0
5
VREG + 0.2
V
V
μs
μs
μs
μs
30
30
380
30
For an 80 pF load
For an 80 pF load
For an 80 pF load
For an 80 pF load
Input High Voltage, VINH
2.4
V
Input Low Voltage, VINL
0.4
V
Input Current, IIN
Input Capacitance, CIN
±10
μA
pF
5
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating State Leakage Current
Floating State Output Capacitance
Output Coding
VDRIVE × 0.±
V
V
μA
pF
ISOURCE = 200 μA
ISINK = 200 μA
0.4
±10
5
Straight binary
1 For dc accuracy specifications, the LSB size for cell voltage measurements is (2 × VREF − 1 V)/40±6. The LSB size for auxiliary ADC input voltage measurements is (2 × VREF)/40±6.
2 ADC unadjusted error includes the INL of the ADC and the gain and offset errors of the VIN0 to VIN6 input channels.
3 The conversion accuracy during cell balancing is decreased due to the activation of the cell balance circuitry. The ADC unadjusted error increases by a factor of 4.
4 Total unadjusted error includes the INL of the ADC and the gain and offset errors of the VIN0 to VIN6 input channels, as well as the reference error, that is, the difference between
the ideal and actual reference voltage and the temperature coefficient of the 2.5 V reference.
5 The conversion accuracy during cell balancing is decreased due to the activation of the cell balance circuitry. The total unadjusted error increases by a factor of 4.
6 For the full analog input range, that is, 1 V to 2 × VREF, the total unadjusted error increases by 20%.
7 The total current measured on the input pins while converting is the sum of the static and dynamic leakage currents. See the Terminology section.
8 Bit D3 of the control register is set to 0 (thermistor termination resistor function is not in use).
± ADC unadjusted error includes the INL of the ADC and the gain and offset errors of the AUXx input channels.
10 Total unadjusted error includes the INL of the ADC and the gain and offset errors of the AUXx input channels, as well as the reference error, that is, the difference between the
ideal and actual reference voltage and the temperature coefficient of the 2.5 V reference.
11
PD
The turn-on settling time is the time from the rising edge of the
signal until the conversion result settles to the specified accuracy. This includes the time required
CNVST
to power up the regulator and the reference. Note that a rising edge on the
PD
input is also required to power up the reference. This rising edge should occur after
the rising edge on
.
12 Sample tested during initial release to ensure compliance.
13 The regulator output voltage is specified with an external 5 mA load in addition to the current required to drive the AVCC, DVCC, and VDRIVE supplies of the AD7280A.
14 This specification refers to the maximum regulator output current that is available for external use.
15 The CBx outputs can be set to 0 V or VREG with respect to the negative terminal of the cell being balanced.
16
CS
The CB1 to CB6 output ramp-up times are defined from the rising edge of the command until the CB output exceeds VREG − 1 V with respect to the negative
terminal of the cell being balanced.
17
CS
The CB1 to CB6 output ramp-down times are defined from the rising edge of the
terminal of the cell being balanced.
command until the CB output falls below 50 mV with respect to the negative
Rev. 0 | Page 4 of 48
AD7280A
POWER SPECIFICATIONS
VDD = 8 V to 30 V, VSS = 0 V, DVCC = AVCC = VREG, VDRIVE = 2.7 V to 5.5 V, TA = −40°C to +105°C, unless otherwise noted.
Table 2.
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
POWER REQUIREMENTS
VDD
8
30
V
Master Device
IDD During Conversion
IDD During Data Readback
IDD During Cell Balancing
IDD Software Power-Down
IDD Full Power-Down Mode
Slave Device
5.6
5.3
5.1
2.5
1.8
7.3
7.0
6.8
2.±
5
mA
mA
mA
mA
μA
IDD During Conversion
IDD During Data Readback
IDD During Cell Balancing
IDD Software Power-Down
IDD Full Power-Down Mode
POWER DISSIPATION
Master Device
6.±
6.5
6.4
3.8
1.8
8.7
8.2
8.0
4.2
5
mA
mA
mA
mA
μA
VDD = 30 V
During Conversion
During Data Readback
During Cell Balancing
Software Power-Down
Full Power-Down Mode
Slave Device
170
160
155
75
220
210
205
±0
mW
mW
mW
mW
μW
54
150
VDD = 30 V
During Conversion
During Data Readback
During Cell Balancing
Software Power-Down
Full Power-Down Mode
210
1±5
1±2
115
54
265
250
240
130
150
mW
mW
mW
mW
μW
Rev. 0 | Page 5 of 48
AD7280A
TIMING SPECIFICATIONS
VDD = 8 V to 30 V, VSS = 0 V, DVCC = AVCC = VREG, VDRIVE = 2.7 V to 5.5 V, TA = −40°C to +105°C, unless otherwise noted.
Table 3.
Parameter1
Min
Typ
Max
Unit
Description
tCONV
ADC conversion time
425
425
560
6±5
720
ns
ns
−40°C to +85°C
−40°C to +105°C
tACQ
tACQ
tACQ
tACQ
ADC acquisition time, Bits[D6:D5] of the control register set to 00
−40°C to +85°C
−40°C to +105°C
ADC acquisition time, Bits[D6:D5] of the control register set to 01
−40°C to +85°C
−40°C to +105°C
ADC acquisition time, Bits[D6:D5] of the control register set to 10
−40°C to +85°C
340
340
400
465
470
ns
ns
665
665
800
1010
1030
ns
ns
1005
1005
1200
1460
1510
ns
ns
−40°C to +105°C
ADC acquisition time, Bits[D6:D5] of the control register set to 11
−40°C to +85°C
1340
1340
1600
200
18±0
1±45
250
ns
ns
ns
−40°C to +105°C
tDELAY
tWAIT
Propagation delay between the falling edges of CNVST of adjacent
parts in the daisy chain
Time required between the end of conversions and the beginning
of readback of the conversion results
5
ꢀs
fSCLK
tQUIET
1
MHz
ns
Frequency of serial read clock
Minimum quiet time required between the end of a serial read and
the start of the next conversion
200
2
t1
0.4
10
50
20
μs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
μs
CNVST low pulse
t2
t3
t4
t5
CS falling edge to SCLK rising edge
Delay from CS falling edge until SDO is three-state disabled
SDI setup time prior to SCLK falling edge
SDI hold time after SCLK falling edge
Data access time after SCLK rising edge
SCLK to data valid hold time
SCLK high pulse width
SCLK low pulse width
CS rising edge to SCLK rising edge
CS rising edge to SDO high impedance
CS high time required between each 32-bit write/read command
5
4
3
t6
28
10
t7
t8
t±
20
0.45 × tSCLK
0.45 × tSCLK
100
4
t10
t11
t12
3
1 Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to ±0% of VDRIVE) and timed from a voltage level of 1.6 V.
All timing specifications given are with a 25 pF load capacitance.
2
CNVST
CNVST
pin is not gated.
Maximum allowed
low pulse time to ensure that a software power-down state is not entered when the
3 Time required for the output to cross 0.4 V or 2.4 V.
4 t10 applies when using a continuous SCLK. Guaranteed by design.
Timing Diagram
CS
t12
t8
t10
32
t2
1
2
3
4
SCLK
SDO
SDI
t7
t9
t11
t3
t6
MSB
MSB – 1
t5
LSB
THREE-STATE
THREE-STATE
t4
MSB
MSB – 1
LSB
Figure 2. Serial Interface Timing Diagram
Rev. 0 | Page 6 of 48
AD7280A
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 4.
Parameter
Rating
VDD to VSS, AGND
−0.3 V to +33 V
VSS to AGND, DGND
−0.3 V to +0.3 V
VIN0 to VIN5 Voltage to VSS, AGND
VIN6 Voltage to VSS, AGND
CB1 Output to VSS, AGND
CBx Output to VIN(x − 1)1
VSS − 0.3 V to VDD + 0.3 V
VDD − 0.3 V to VDD + 1 V
−0.3 V to DVCC + 0.3 V
−0.3 V to VIN(x − 1)1 + 7 V
To conform with IPC 2221 industrial standards, it is advisable
to use conformal coating on the high voltage pins.
THERMAL RESISTANCE
AUX1 to AUX6 Voltage to VSS, AGND −0.3 V to AVCC + 0.3 V
AUXTERM Voltage to VSS, AGND
AVCC to VSS, AGND, DGND
DVCC to AVCC
−0.3 V to AVCC + 0.3 V
−0.3 V to +7 V
−0.3 V to +0.3 V
−0.3 V to +7 V
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 5. Thermal Resistance
DVCC to VSS, DGND
Package Type
θJA
θJC
Unit
VDRIVE to VSS, AGND
−0.3 V to +7 V
48-Lead LQFP (ST-48)
76.2
17
°C/W
AGND to DGND
Digital Input Voltage to VSS, DGND
−0.3 V to +0.3 V
−0.3 V to VDRIVE + 0.3 V
Digital Output Voltage to VSS, DGND −0.3 V to VDRIVE + 0.3 V
ESD CAUTION
Input Current to Any Pin Except
Supply Pins2
±10 mA
Operating Temperature Range
Storage Temperature Range
Junction Temperature
−40°C to +105°C
−65°C to +150°C
150°C
Pb-Free Temperature,
Soldering Reflow
260(+0)°C
ESD
2 kV
1 x = 2 to 6.
2 Transient currents of up to 100 mA do not cause SCR latch-up.
Rev. 0 | Page 7 of 48
AD7280A
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
48 47 46 45 44 43 42 41 40 39 38 37
1
36
35
34
33
32
31
30
29
28
27
26
25
VIN6
AUX3
AUX4
AUX5
AUX6
PIN 1
2
3
CB6
VIN5
CB5
VIN4
CB4
VIN3
CB3
VIN2
CB2
VIN1
CB1
4
5
AUX
TERM
AD7280A
TOP VIEW
(Not to Scale)
6
AGND
7
AV
CC
8
V
DRIVE
9
ALERTlo
ALERT
SDO
10
11
12
SDOlo
13 14 15 16
18
20 21
17
19
22 24
23
Figure 3. Pin Configuration
Table 6. Pin Function Descriptions
Pin No. Mnemonic Description
1, 3, 5, 7, ±, VIN6 to VIN0
11, 13
Analog Input 6 to Analog Input 0. VIN0 should be connected to the base of the series-connected battery cells.
VIN1 should be connected to the top of Cell 1, VIN2 should be connected to the top of Cell 2, and so on (see
Figure 28 and Figure 2±).
2, 4, 6, 8,
10, 12
CB6 to CB1
MASTER
Cell Balance Output 6 to Cell Balance Output 1. These pins provide a voltage output that can be used to supply
the gate drive of an external cell balancing transistor. Each CBx output provides a 0 V or 5 V voltage output
referenced to the absolute amplitude of the negative terminal of the battery cell that is being balanced.
Voltage Input. Connect the MASTER pin of the AD7280A that is connected directly to the DSP/microprocessor
to the VDD supply pin through a 10 kΩ resistor. In an application with two or more AD7280As in a daisy chain,
the MASTER pins of the remaining AD7280As in the daisy chain should be tied to their respective VSS supply
pins through 10 kΩ resistors.
14
15
PD
Power-Down Input. This input is used to power down the AD7280A. When the AD7280A acts as a master, the
PD input is supplied from the DSP/microprocessor. When the AD7280A acts as a slave in a daisy chain, the
PD input should be connected to the PDhi output of the AD7280A immediately below it in potential in the
daisy chain.
16
VDD
Positive Power Supply Voltage for the High Voltage Analog Input Structure of the AD7280A. The supply must be
greater than the minimum voltage of 8 V. VDD can be supplied directly from the cell with the highest potential
of the four, five, or six cell battery stacks that the AD7280A is monitoring. The maximum voltage that should
be applied between VDD and VSS is 30 V. Place 10 μF and 100 nF decoupling capacitors on the VDD pin.
17
18
VSS
Negative Power Supply Voltage for the High Voltage Analog Input Structure of the AD7280A. This input should
be at the same potential as the AGND/DGND voltage.
Analog Voltage Output, 5.2 V. The internally generated VREG voltage, which provides the supply voltage for
the ADC core, is available on this pin for use external to the AD7280A. Place 1 μF and 100 nF decoupling
capacitors on the VREG pin.
VREG
1±
20
DVCC
Digital Supply Voltage, 4.± V to 5.5 V. The DVCC and AVCC voltages should ideally be at the same potential.
For best performance, it is recommended that the DVCC and AVCC pins be shorted together to ensure that
the voltage difference between them never exceeds 0.3 V, even on a transient basis. This supply should be
decoupled to DGND. Place 100 nF decoupling capacitors on the DVCC pin. The DVCC supply pin should be
connected to the VREG output.
DGND
Digital Ground. Ground reference point for all digital circuitry on the AD7280A. The DGND and AGND voltages
should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis.
Rev. 0 | Page 8 of 48
AD7280A
Pin No.
Mnemonic
Description
21
CS
Chip Select Input. The CS input is used to frame the input and output data on the SPI and daisy-chain
interfaces. On the master AD7280A device, the CS input is supplied from the DSP/microprocessor. When
the AD7280A acts as a slave in a daisy chain, this input should be connected to the CShi output of the
AD7280A immediately below it in potential in the daisy chain.
22
23
SCLK
SDI
Serial Clock Input. On the master AD7280A device, the SCLK input is supplied from the DSP/microprocessor.
When the AD7280A acts as a slave in a daisy chain, this input should be connected to the SCLKhi output of
the AD7280A immediately below it in potential in the daisy chain.
Serial Data Input. Data to be written to the on-chip registers is provided on this input and is clocked into the
AD7280A on the falling edge of the SCLK input. On the master AD7280A device, SDI is the data input of the
SPI interface. When the AD7280A acts as a slave in a daisy chain, this input accepts data from the SDOhi
output of the AD7280A immediately below it in potential in the daisy chain.
24
CNVST
Convert Start Input. The conversion is initiated on the falling edge of CNVST. On the master AD7280A, the
CNVST pulse is supplied from the DSP/microprocessor; this input can also be tied to DVCC and the conversion
initiated through the serial interface. When the AD7280A acts as a slave in a daisy chain, this input should be
connected to the CNVSThi output of the AD7280A immediately below it in potential in the daisy chain.
25
26
SDOlo
SDO
Serial Data Output in Daisy-Chain Mode. On the master AD7280A device, this output should be connected
to VSS either directly or through a pull-down, 1 kΩ resistor. When the AD7280A acts as a slave in a daisy chain,
this output should be connected to the SDIhi input of the AD7280A immediately below it in potential in the
daisy chain.
Serial Data Output. The conversion output data or the register output data is supplied to this pin as a serial
data stream. The bits are clocked out on the rising edge of the SCLK input; 32 SCLKs are required to access
the data. On the master AD7280A device, the SDO output should be connected to the DSP/microprocessor.
The SDO outputs of the remaining AD7280As in the daisy chain should be connected to VSS either directly or
through a pull-down, 1 kΩ resistor.
27
28
2±
ALERT
ALERTlo
VDRIVE
Digital Output. This flag indicates cell or auxiliary ADC input overvoltage or undervoltage. The ALERT output of
the master AD7280A should be connected to the DSP/microprocessor. The ALERT outputs of the remaining
AD7280As in the daisy chain should be connected to VSS either directly or through a pull-down, 1 kΩ resistor.
Alert Output in Daisy-Chain Mode. On the master AD7280A, this output should be connected to VSS either
directly or through a pull-down, 1 kΩ resistor. When the AD7280A acts as a slave in a daisy chain, this output
should be connected to the ALERThi input of the AD7280A immediately below it in potential in the daisy chain.
Logic Power Supply Input. The voltage supplied at this pin determines the voltage at which the SPI interface
operates. This pin should be decoupled to DGND. On the master AD7280A device, the voltage range on this
pin is 2.7 V to 5.5 V. The VDRIVE voltage can be different from the voltage at AVCC and DVCC, but it should never
exceed either by more than 0.3 V. The VDRIVE pin of the remaining AD7280As in the daisy chain should be
connected to VREG
.
30
31
AVCC
Analog Supply Voltage for the ADC Core, 4.± V to 5.5 V. The AVCC and DVCC voltages should ideally be at the
same potential. For best performance, it is recommended that the AVCC and DVCC pins be shorted together to
ensure that the voltage difference between them never exceeds 0.3 V, even on a transient basis. This supply
should be decoupled to AGND. Place 100 nF decoupling capacitors on the AVCC pin. The AVCC supply pin
should be connected to the VREG output.
Analog Ground. This pin is the ground reference point for all analog circuitry on the AD7280A. This input should
be at the same potential as the base of the series-connected battery cells. The AGND and DGND voltages
should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis.
AGND
32
AUXTERM
Thermistor Termination Resistor Input. If this function is not required in the application, it is recommended
that this pin be connected to VREG through a 10 kΩ resistor.
33 to 38
AUX6 to AUX1 Auxiliary, Single-Ended 5 V ADC Inputs. If any of these inputs is not required in the application, it is
recommended that the pin be connected to VREG through a 10 kΩ resistor.
3±
40
CREF
VREF
Reference Capacitor. A 100 nF decoupling capacitor to REFGND should be placed on this pin.
Reference Output, 2.5 V. The on-chip reference is available on this pin for use external to the AD7280A.
A 1 μF decoupling capacitor to REFGND is recommended on this pin.
41
42
REFGND
ALERThi
Reference Ground. This pin is the ground reference point for the internal band gap reference circuitry on
the AD7280A. The REFGND voltage should be at the same potential as the AGND voltage.
Alert Input in Daisy-Chain Mode. The alert signal from each AD7280A in the daisy chain is passed through
the ALERTlo output and the ALERThi input of each AD7280A in the chain and is supplied to the DSP/micro-
processor through the ALERT output of the master AD7280A. This input should be connected to the ALERTlo
output of the AD7280A immediately above it in potential in the daisy chain. The AD7280A at the highest
potential in the stack does not require an alert input; in this case, the pin should be connected to VDD
through a 1 kΩ resistor.
Rev. 0 | Page ± of 48
AD7280A
Pin No.
Mnemonic
Description
43
SDIhi
Serial Data Input in Daisy-Chain Mode. The data from each AD7280A in the daisy chain is passed through the
SDOlo output and the SDIhi input of each AD7280A in the chain and is supplied to the DSP/microprocessor
through the SDO output of the master AD7280A. This input should be connected to the SDOlo output of the
AD7280A immediately above it in potential in the daisy chain. The AD7280A at the highest potential in the
stack does not require a serial data input in daisy-chain mode; in this case, the pin should be connected to
VDD through a 1 kΩ resistor.
44
CNVSThi
Conversion Start Output in Daisy-Chain Mode. The convert start signal from the DSP/microprocessor supplied
to the CNVST input of the master AD7280A is passed through each AD7280A by means of the CNVST input
and the CNVSThi output. This output should be connected to the CNVST pin of the AD7280A immediately
above it in potential in the daisy chain. The AD7280A at the highest potential in the stack does not require
a daisy-chain conversion start output; in this case, the pin should be connected to VDD.
45
46
47
SDOhi
SCLKhi
CShi
Serial Data Output in Daisy-Chain Mode. The serial data input from the DSP/microprocessor supplied to the
SDI input of the master AD7280A is passed through each AD7280A by means of the SDI input and the SDOhi
output. This output should be connected to the SDI input of the AD7280A immediately above it in potential
in the daisy chain. The AD7280A at the highest potential in the stack does not require a daisy-chain serial
data output; in this case, the pin should be connected to VDD.
Serial Clock Output in Daisy-Chain Mode. The clock signal from the DSP/microprocessor supplied to the
SCLK input of the master AD7280A is passed through each AD7280A by means of the SCLK input and the
SCLKhi output. This output should be connected to the SCLK input of the AD7280A immediately above it in
potential in the daisy chain. The AD7280A at the highest potential in the stack does not require a daisy-chain
serial clock output; in this case, the pin should be connected to VDD.
Chip Select Output in Daisy-Chain Mode. The chip select signal from the DSP/microprocessor supplied to the
CS input of the master AD7280A is passed through each AD7280A by means of the CS input and the CShi
output. This output should be connected to the CS input of the AD7280A immediately above it in potential
in the daisy chain. The AD7280A at the highest potential in the stack does not require a daisy-chain chip
select output; in this case, the pin should be connected to VDD.
48
PDhi
Power-Down Output in Daisy-Chain Mode. The power-down signal from the DSP/microprocessor supplied
to the PD input of the master AD7280A is passed through each AD7280A by means of the PD input and the
PDhi output. This output should be connected to the PD input of the AD7280A immediately above it in
potential in the daisy chain. The AD7280A at the highest potential in the stack does not require a daisy-chain
power-down output; in this case, the pin should be connected to VDD.
Rev. 0 | Page 10 of 48
AD7280A
TYPICAL PERFORMANCE CHARACTERISTICS
5.5
8
7
6
5
4
3
2
1
V
V
V
V
= 8V
= 10V
= 22.5V
= 29.9V
DD
DD
DD
DD
SLAVE CURRENTS
MASTER CURRENTS
5.4
5.3
5.2
5.1
5.0
4.9
SLAVE, V = 8V
DD
SLAVE, V = 10V
DD
SLAVE, V = 29.9V
DD
MASTER, V = 8V
DD
MASTER, V = 10V
DD
MASTER, V = 29.9V
DD
–40
–20
0
20
40
60
80
100
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 4. VREG vs. Temperature for Different Supply Voltages,
VREG Connected to AVCC and DVCC
Figure 7. IDD During Cell Balancing vs. Temperature
for Different Supply Voltages
5.5
8
7
6
5
4
3
2
1
V
V
V
V
= 8V
= 10V
= 22.5V
= 29.9V
SLAVE, V = 8V
DD
SLAVE, V = 10V
DD
DD
DD
DD
DD
SLAVE, V = 29.9V
DD
5.4
5.3
5.2
5.1
5.0
4.9
MASTER, V = 8V
DD
MASTER, V = 10V
DD
MASTER, V = 29.9V
DD
SLAVE CURRENTS
MASTER CURRENTS
–40
–20
0
20
40
60
80
100
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 5. VREG vs. Temperature for Different Supply Voltages,
VREG Connected to AVCC and DVCC, 5 mA External Load
Figure 8. IDD During Software Power-Down vs. Temperature
for Different Supply Voltages
8
10,000
9149
SLAVE CURRENTS
7
8000
6000
4000
2000
0
6
5
4
3
2
1
MASTER CURRENTS
SLAVE, V = 8V
DD
SLAVE, V = 10V
SLAVE, V = 29.9V
DD
MASTER, V = 8V
MASTER, V = 10V
DD
MASTER, V = 29.9V
DD
DD
460
386
5
DD
–40
–20
0
20
40
60
80
100
2660 2661 2662 2663 2664 2665 2666 2667 2668
CODE
TEMPERATURE (°C)
Figure 6. IDD During Conversion vs. Temperature
for Different Supply Voltages
Figure 9. Histogram of Codes for 10,000 Samples,
Odd Cell Voltage Channels
Rev. 0 | Page 11 of 48
AD7280A
10,000
8000
6000
4000
2000
0
PART 1
PART 4
PART 7
PART 10
PART 2
PART 5
PART 8
PART 11
PART 3
PART 6
PART 9
PART 12
2.508
2.506
2.504
2.502
2.500
2.498
2.496
8870
956
167
7
–40
–20
0
20
40
60
80
100
2660 2661 2662 2663 2664 2665 2666 2667 2668
CODE
TEMPERATURE (°C)
Figure 13. VREF vs. Temperature for Different Parts
Figure 10. Histogram of Codes for 10,000 Samples,
Even Cell Voltage Channels
7.5
6.0
10,000
8000
6000
4000
2000
0
V
V
V
V
V
= 8V
= 10V
= 16.8V
= 22.5V
= 29.9V
DD
DD
DD
DD
DD
9072
4.5
3.0
1.5
0
–1.5
–3.0
–4.5
692
236
–40
–20
0
20
40
60
80
100
2942 2943 2944 2945 2946 2947 2948 2949 2950 2951 2952
CODE
TEMPERATURE (°C)
Figure 11. Histogram of Codes for 10,000 Samples,
Auxiliary Channels
Figure 14. Total Unadjusted Error for Even Cell Voltage Channels (Absolute
Value) vs. Temperature for Different Supply Voltages
2.508
2.507
2.506
2.505
2.504
2.503
2.502
2.501
2.500
2.499
2.498
2.497
2.496
7.5
V
V
V
V
V
= 8V
= 10V
= 16.8V
= 22.5V
= 29.9V
V
V
V
V
V
= 8V
= 10V
= 16.8V
= 22.5V
= 29.9V
DD
DD
DD
DD
DD
DD
DD
DD
DD
DD
6.0
4.5
3.0
1.5
0
–1.5
–3.0
–4.5
–40
–20
0
20
40
60
80
100
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 12. VREF vs. Temperature for Different Supply Voltages
Figure 15. Total Unadjusted Error for Odd Cell Voltage Channels (Absolute
Value) vs. Temperature for Different Supply Voltages
Rev. 0 | Page 12 of 48
AD7280A
7.5
6.0
V
V
V
V
V
= 8V
= 10V
= 16.8V
= 22.5V
= 29.9V
DD
DD
DD
DD
DD
5
4
3
2
1
0
4.5
3.0
1.5
0
–1.5
–3.0
–4.5
PD
V
V
REG
REF
0
2
4
6
8
10
–40
–20
0
20
40
60
80
100
TIME (ms)
TEMPERATURE (°C)
Figure 16. Total Unadjusted Error for Auxiliary Channels (Absolute Value)
vs. Temperature for Different Supply Voltages
Figure 19. Power-Up Time, 10 μF Capacitor on the VREF and VREG Pins
5
4
3
2
5
4
PD
V
REG
REF
V
3
2
1
0
1
PD
V
REG
REF
V
0
0
2
4
6
8
10
0
2
4
6
8
10
TIME (ms)
TIME (ms)
Figure 17. Power-Up Time, 1 μF Capacitor on the VREF and VREG Pins
Figure 20. Power-Down Time, 10 μF Capacitor on the VREF and VREG Pins
5.2
4.8
4.4
4.0
3.6
3.2
5
PD
V
REG
REF
V
4
3
2
1
0
0
2
4
6
8
10
0
100
200
300
400
500
600
700
800
TIME (ms)
LOAD CURRENT (nA)
Figure 18. Power-Down Time, 1 μF Capacitor on the VREF and VREG Pins
Figure 21. CBx Output Voltage vs. Load Current
Rev. 0 | Page 13 of 48
AD7280A
TERMINOLOGY
Differential Nonlinearity (DNL)
Output Voltage Hysteresis
DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
Output voltage hysteresis, or thermal hysteresis, is defined as
the absolute maximum change of reference output voltage after
the device is cycled through temperature from either T_HYS+
or T_HYS−, where:
Integral Nonlinearity (INL)
INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale (a point 1 LSB
below the first code transition) and full scale (a point 1 LSB
above the last code transition).
T_HYS+ = +25°C to TMAX to +25°C
T_HYS− = +25°C to TMIN to +25°C
Output voltage hysteresis is expressed in ppm using the follow-
ing equation:
Offset Error
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
V
REF (25°C) −VREF (T_HYS)
6
Offset error applies to straight binary output coding. It is the
deviation of the first code transition (000 ... 000) to (000 ... 001)
from the ideal, that is, AGND + 1 LSB for AUX1 to AUX6 and
1 V + AGND + 1 LSB for VIN0 to VIN6.
V
HYS (ppm)=
× 10
V
REF (25°C)
where:
V
REF(25°C) = VREF at 25°C.
VREF(T_HYS) is the maximum change of VREF at T_HYS+ or
Offset Error Match
Offset error match is the difference in zero code error across all
six channels.
T_HYS−.
Static Leakage Current
Gain Error
Static leakage current is the current measured on the cell voltage
and/or the auxiliary ADC inputs when the device is static, that
is, not converting.
Gain error applies to straight binary output coding. It is the
deviation of the last code transition (111 ... 110) to (111 ... 111)
from the ideal (that is, 2 × VREF − 1 LSB) after adjusting for the
offset error.
Dynamic Leakage Current
Dynamic leakage current is the current measured on the cell
voltage and/or the auxiliary ADC inputs when the device is
converting, with the static leakage current subtracted. Dynamic
leakage current is specified with a convert start pulse frequency
of 10 Hz, that is, every 100 ms. The dynamic leakage current for
a different conversion rate can be calculated using the following
equation:
Gain Error Match
Gain error match is the difference in gain error across all six
channels.
ADC Unadjusted Error
ADC unadjusted error includes the INL error and the offset and
gain errors of the ADC and measurement channel.
⎛
⎜
⎞
⎟
Total Unadjusted Error (TUE)
IDYN(A) × fCNVST(B)
IDYN(B)
=
TUE is the maximum deviation of the output code from the ideal.
Total unadjusted error includes the INL error, the offset and gain
errors, and the reference errors. Reference errors include the
difference between the actual and ideal reference voltage (that
is, 2.5 V) and the reference voltage temperature coefficient.
⎜
⎝
⎟
⎠
fCNVST(A)
where:
DYN(A) is the dynamic leakage current at the convert start
frequency, fCNVST(A) (see Table 1).
DYN(B) is the dynamic leakage current at the desired convert
start frequency, fCNVST(B)
I
I
Reference Voltage Temperature Coefficient
The reference voltage temperature coefficient is derived from
.
the maximum and minimum reference output voltage (VREF
)
measured between TMIN and TMAX. It is expressed in ppm/°C
using the following equation:
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
V
REF (Max) − VREF (Min)
6
TCVREF (ppm/°C) =
× 10
2.5 V × (TMAX − TMIN
)
where:
V
V
REF(Max) is the maximum VREF between TMIN and TMAX
REF(Min) is the minimum VREF between TMIN and TMAX
.
.
T
T
MAX = +85°C or +105°C.
MIN = −40°C.
Rev. 0 | Page 14 of 48
AD7280A
THEORY OF OPERATION
The AD7280A provides six analog output voltages that can be
used to control external transistors as part of a cell balancing
circuit. Each cell balance output provides a 0 V or 5 V voltage,
with respect to the potential on the base of each individual cell,
that can be applied to the gate of the external cell balancing
transistors.
CIRCUIT INFORMATION
The AD7280A is a lithium ion (Li-Ion) battery monitoring chip
that can monitor the voltage and temperature of four, five, or six
series-connected Li-Ion battery cells. The AD7280A also provides
an interface that can be used to control external transistors for
cell balancing.
The AD7280A features a daisy-chain interface. Individual
AD7280A devices can monitor the cell voltages and tempera-
tures of six cells. A chain of AD7280As can be used to monitor
the cell voltages and temperatures of a larger number of cells. The
conversion data from each AD7280A in the chain passes to the
system controller via a single SPI interface. Control data can
similarly be passed via the SPI up the chain to each individual
AD7280A.
The VDD and VSS supplies required by the AD7280A should
be taken from battery cells being monitored by the part. An
internal VREG rail is generated to provide power for the ADC
and the internal interface circuitry. This VREG voltage is available
on an output pin for use external to the AD7280A.
The AD7280A consists of a high voltage input multiplexer, a low
voltage input multiplexer, and a SAR ADC. The high voltage
multiplexer allows four, five, or six series-connected Li-Ion
battery cells to be measured. The low voltage multiplexer provides
the user with six single-ended ADC inputs that can be used in
combination with external thermistors to measure the tempera-
ture of each battery cell. The auxiliary ADC inputs can also be
used for external diagnostics in the application. Initiating conver-
sions on all 12 channels, that is, the six cell voltage channels and
The AD7280A includes an on-chip 2.5 V reference. The
reference voltage is available for use external to the AD7280A.
The AD7280A also has a VDRIVE feature to control the voltage at
which the serial interface operates. VDRIVE allows the ADC to
easily interface to both 3 V and 5 V processors. For example, in
the recommended configuration, the AD7280A is operated with
a supply of 5 V; however, the VDRIVE pin can be powered from
a 3 V supply, allowing a large dynamic range with low voltage
digital processors.
CNVST
the six auxiliary ADC channels, requires only a single
pulse. Alternatively, the conversion can be initiated through the
CS
rising edge of . Each conversion result is stored in an individual
result register (see Table 13).
CONVERTER OPERATION
Each individual cell voltage and auxiliary ADC measurement
requires a minimum of 1 μs to acquire and complete a conver-
sion. Depending on the external components connected to the
analog inputs of the AD7280A, additional acquisition time may
be required. A higher acquisition time can be selected through
the control register. The AD7280A also provides a conversion
averaging option that can be selected through the control register.
This option allows the user to complete two, four, or eight averages
on each cell voltage and auxiliary ADC measurement. The aver-
aged conversion results are stored in the result registers. On
power-up, the default combined acquisition and conversion
time is 1 μs, with the averaging register set to 0, that is, a single
conversion per channel.
The conversion paths of the AD7280A consist of a high voltage
input multiplexer or a low voltage input multiplexer and a SAR
ADC. The high voltage multiplexer selects the pair of analog
inputs, VIN0 to VIN6, that is to be converted. The voltage of
each individual cell is measured by converting the difference
between adjacent analog inputs, that is, VIN1 − VIN0, VIN2 −
VIN1, and so on (see Figure 22 and Figure 23). The low voltage
multiplexer selects the auxiliary ADC input, AUX1 to AUX6,
that is to be converted. The conversion results for each cell
voltage and auxiliary ADC input can be accessed tWAIT after
the programmed conversion sequence is completed.
VIN6
VIN5
VIN4
VIN3
VIN2
VIN1
The results of the cell voltage and auxiliary ADC conversions
are read back via the 4-wire serial peripheral interface (SPI).
The SPI is also used to write to and read from the internal
registers.
The AD7280A features an alert function that can be triggered if
the voltage conversion results or the auxiliary ADC conversion
results exceed the maximum and minimum voltage thresholds
selected by the user. The alert modes and threshold levels are
selected by writing to internal registers.
ADC V
ADC V
IN+
IN–
VIN0
Figure 22. Mux Configuration During VIN1 to VIN0 Sampling
Rev. 0 | Page 15 of 48
AD7280A
ANALOG INPUT STRUCTURE
VIN6
VIN5
VIN4
VIN3
VIN2
VIN1
VIN0
Figure 26 shows the equivalent circuit of the analog input
structure of the AD7280A. The diodes provide ESD protection.
The resistors are lumped components made up of the on
resistance of the input multiplexer, internal track resistance,
and other internal switches. The value of these resistors is
approximately 300 Ω typical. Capacitor C1 is also a lumped
component made up of pin capacitance, ESD diodes, and switch
capacitance, whereas Capacitor C2 is the sampling capacitor
of the ADC. The total lumped capacitance of C1 and C2 is
approximately 15 pF.
ADC V
ADC V
IN+
IN–
V
DD
Figure 23. Mux Configuration During VIN2 to VIN1 Sampling
The ADC is a successive approximation register analog-to-
digital converter (SAR ADC). The converter is composed of
a comparator, a SAR, control logic, and two capacitive DACs.
Figure 24 shows a simplified schematic of the converter. During
the acquisition phase, the SW1, SW2, and SW3 switches are
closed. The sampling capacitor array acquires the signal on the
input during this phase.
D
D
C2
R1
V
IN+
C1
V
SS
V
DD
D
D
V
CAPACITIVE
DAC
C2
REF
R1
V
IN–
COMPARATOR
C1
C
C
B
S
S
V
V
IN+
A
A
SW1
SW2
CONTROL
LOGIC
SW3
V
SS
IN–
Figure 26. Equivalent Analog Input Circuit
B
CAPACITIVE
DAC
V
REF
TRANSFER FUNCTION
The output coding of the AD7280A is straight binary. The designed
code transitions occur at successive integer LSB values (that is,
1 LSB, 2 LSBs, and so on). The LSB size is dependent on whether
the cell voltage or the auxiliary ADC inputs are being measured.
The analog input range of the voltage inputs is 1 V to 5 V, and
the analog input range of the auxiliary ADC inputs is 0 V to 5 V.
The ideal transfer characteristic is shown in Figure 27.
Figure 24. ADC Configuration During Acquisition Phase
When the ADC starts a conversion, SW3 opens, and SW1 and
SW2 move to Position B, causing the comparator to become
unbalanced (see Figure 25). The control logic and capacitive DACs
are used to add and subtract fixed amounts of charge to return
the comparator to a balanced condition. When the comparator
is rebalanced, the conversion is complete. The control logic gen-
erates the ADC output code. This output code is then stored in
the appropriate register for the input that has been converted.
Table 7. LSB Sizes for Each Analog Input Range
Input
Range
Full-Scale
Range
Selected Inputs
Cell Voltage
Auxiliary ADC Inputs
LSB Size
±76 μV
1.22 mV
V
CAPACITIVE
DAC
REF
1 V to 5 V
0 V to 5 V
4 V/40±6
5 V/40±6
COMPARATOR
C
C
B
S
S
V
V
IN+
A
A
SW1
SW2
CONTROL
LOGIC
SW3
111...111
111...110
IN–
B
CAPACITIVE
DAC
V
REF
111...000
011...111
Figure 25. ADC Configuration During Conversion Phase
000...010
000...001
000...000
1V + 1LSB
AGND + 1LSB
5V – 1LSB 4V INPUT RANGE
5V – 1LSB 5V INPUT RANGE
ANALOG INPUT
Figure 27. Ideal Transfer Characteristic
Rev. 0 | Page 16 of 48
AD7280A
TYPICAL CONNECTION DIAGRAMS
0.1µF
10µF
10kΩ
10kΩ
V
MASTER
VIN6
DD
V
REG
1µF
0.1µF
0.1µF
10kΩ
10kΩ
DV
AV
CC
CC
CB6
VIN5
10kΩ
10kΩ
V
DRIVE
CB5
V
VIN4
REF
1µF
0.1µF
10kΩ
10kΩ
C
REF
AD7280A
CB4
VIN3
OPTIONAL INTERFACE PINS
10kΩ
10kΩ
CB3
ALERT
CNVST
PD
VIN2
10kΩ
10kΩ
DSP/MICRO-
PROCESSOR
CB2
SDO
SCLK
SDI
VIN1
10kΩ
10kΩ
CB1
CS
VIN0
V
SS
4-WIRE SPI INTERFACE
Figure 28. AD7280A Configuration Diagram for Six Battery Cells
The AD7280A can be used to monitor four, five, or six battery
cells connected in series. A typical configuration for a six-cell
battery monitoring application is shown in Figure 28. However,
lithium ion battery applications require a significant number of
individual cells to provide the required output voltage. Figure 29
shows the recommended configuration of a chain of AD7280As
monitoring a larger battery stack. The daisy-chain interface of the
AD7280A allows each individual AD7280A to communicate with
the AD7280A immediately above and below it. The daisy-chain
interface allows the AD7280As to be electrically connected to
the battery management chip without the need for individual
isolation devices between each AD7280A.
The 10 kꢀ resistor in series with the inputs combined with a
100 nF capacitor across the adjacent differential inputs acts as
a low-pass filter. The 10 kꢀ resistors provide protection for the
analog inputs in the event of an overvoltage or undervoltage on
those inputs, for example, if any of the cell voltage inputs is
incorrectly shorted to VDD or VSS. The resistors also provide
protection during the initial connection of the daisy chain of
AD7280As to the battery stack. For more information about the
daisy-chain interface, see the Daisy-Chain Interface section.
In an application that includes a safety mechanism designed to
open circuit the battery stack, additional isolation is required
between the AD7280A above the break point and the battery
management chip.
As shown in Figure 29, it is recommended that a Zener diode be
placed across the supplies of each AD7280A. This prevents an
overvoltage across the supplies of each AD7280A during the
initial connection of the daisy chain of AD7280As to the battery
stack. A voltage rating of 30 V is suggested for this Zener diode,
but lower values can also be used to suit the application.
A suggested configuration for the external cell balancing circuit
is shown in Figure 28. This configuration also includes 10 kꢀ
resistors in series with the cell balance outputs. These resistors
provide protection for the cell balance outputs in the event of
an overvoltage or undervoltage on those inputs. See the Cell
Balancing Outputs section for more information.
Rev. 0 | Page 17 of 48
AD7280A
V
n
1kΩ
DD
V
n
DD
10µF
100nF
100nF
V
(n – 1)
DD
V
REG
10kΩ
10kΩ
10kΩ
VIN6
VIN5
VIN4
VIN3
VIN2
1µF
DV
AV
CC
CC
100nF
0.1µF
V
100nF
100nF
100nF
100nF
100nF
DRIVE
ALERT
SDO
1kΩ
1kΩ
10kΩ
10kΩ
AD7280A
10kΩ
MASTER
10kΩ
10kΩ
VIN1
VIN0
1µF
V
C
REF
REF
0.1µF
V
(n – 1)
DD
22pF
22pF
22pF
22pF
22pF
22pF
22pF
7
FERRITE
V
1
DD
10µF
100nF
100nF
V
0
DD
V
REG
10kΩ
10kΩ
10kΩ
VIN6
VIN5
VIN4
VIN3
VIN2
1µF
DV
AV
CC
CC
100nF
100nF
100nF
100nF
100nF
100nF
0.1µF
V
DRIVE
ALERT
SDO
NOTES
1kΩ
1kΩ
ALL AD7280A DEVICES ON THE DAISY CHAIN
1
10kΩ
10kΩ
SHOULD BE LOCATED ON THE SAME PCB.
AD7280A
PLACE 22pF DAISY-CHAIN CAPACITORS
AS CLOSE AS POSSIBLE TO THEIR
TERMINATING PINS, THAT IS, CLOSE TO
THE PIN THAT HAS THE ARROW POINTING
TO IT ON THE DIAGRAM.
2
10kΩ
MASTER
10kΩ
10kΩ
VIN1
VIN0
1µF
V
C
REF
ROUTE V AND V TRACES TO ENSURE
DD
SS
3
REF
A LOW IMPEDANCE CONNECTION BETWEEN THEM.
0.1µF
ROUTE DAISY-CHAIN TRACKS ON AN INNER
PCB LAYER.
4
5
3
2
V
0
DD
22pF
22pF
22pF
22pF
22pF
22pF
22pF
4
6
ADD A V PLANE FROM THE UPPER SLAVE
SS
DEVICE EXTENDED DOWN OVER AND UNDER
THE DAISY CHAIN TO ACT AS A SHIELD FOR
THE DAISY CHAIN.
PLACE AD7280A PARTS AS CLOSE TOGETHER
AS POSSIBLE ON THE BOARD TO MINIMIZE
THE LENGTH OF THE DAISY-CHAIN TRACKS.
6
7
V
0
DD
FERRITES ON THE V LINES CAN BE REPLACED
DD
WITH 20Ω RESISTORS EXCEPT IN THE CASE OF THE
5
10kΩ
10µF
100nF
V
0 CONNECTION. IN THIS CASE, THE 20Ω RESISTOR
SS
SHOULD BE REPLACED WITH A 0Ω RESISTOR.
100nF
V
REG
1µF
10kΩ
10kΩ
10kΩ
DV
AV
CC
CC
VIN6
VIN5
VIN4
VIN3
VIN2
0.1µF
100nF
100nF
100nF
100nF
100nF
100nF
OPTIONAL INTERFACE PINS
V
DRIVE
ALERT
CNVST
PD
10kΩ
10kΩ
AD7280A
DSP/MICRO-
PROCESSOR
SDO
SCLK
SDI
10kΩ
10kΩ
VIN1
VIN0
CS
V
0
SS
1µF
1kΩ
0.1µF
4-WIRE SPI INTERFACE
Figure 29. AD7280A Daisy-Chain Configuration
Rev. 0 | Page 18 of 48
AD7280A
The conversion sequence—that is, the order in which the cell
voltages and auxiliary ADC inputs are converted—is shown in
Figure 31 and Figure 32. The cell voltage inputs are converted in
reverse order, that is, Cell 6 is followed by Cell 5, and so on.
However, the auxiliary ADC inputs are converted in increasing
numerical order, that is, AUX1 is followed by AUX2, and so on.
For example, when all 12 inputs are selected for conversion, the
conversion of Cell 1, that is, VIN1 to VIN0, is followed by the
conversion of the AUX1 input.
REFERENCE
The internal reference is temperature compensated to 2.5 V. The
reference is trimmed to provide a typical drift of 3 ppm/°C. As
shown in Figure 30, the internal reference circuitry consists of a
1.2 V band gap reference and a reference buffer. The 2.5 V refer-
ence is available at the VREF pin. The VREF pin should be decoupled
to REFGND using a 1 μF or greater ceramic capacitor. The CREF
pin should be decoupled to REFGND using a 0.1 μF or greater
ceramic capacitor. The 2.5 V reference is capable of driving an
external load of up to 10 kΩ.
When all selected conversions are completed, the VIN6 and VIN5
voltage inputs are again selected through the multiplexer, and
the voltage across Cell 6 is acquired in preparation for the next
conversion request. This is the default state for the multiplexer.
REFGND
V
REF
C
REF
AV
Bits[D15:D14] of the control register select the cell voltage and
auxiliary ADC inputs to be converted. There are four options
available (see Table 8).
BAND GAP
1.2V
ADC SELF-TEST
VOLTAGE
CC
Figure 30. AD7280A Internal Reference
CONVERTING CELL VOLTAGES AND AUXILIARY
ADC INPUTS
Table 8. Cell Voltage and Auxiliary ADC Input Selection
Bits[D15:D14] Voltage Inputs
Auxiliary ADC Inputs
00
01
10
11
6 to 1
6 to 1
6 to 1
ADC self-test
1 to 6
1, 3, and 5
None
A conversion can be initiated on the AD7280A using either the
CNVST
input or the serial interface (see the Conversion Start
Format section). A single conversion command initiates conver-
sions on all selected channels of the AD7280A. As described in
the Converter Operation section, the voltage of each individual
battery cell is measured by converting the difference between
adjacent analog inputs. The first cell to be converted following a
convert start command is Cell 6, which is the difference between
VIN6 and VIN5. At the end of the first conversion, the AD7280A
generates an internal end-of-conversion (EOC) signal. This internal
EOC selects the next cell voltage inputs for measurement through
the multiplexer, that is, the difference between VIN5 and VIN4.
The new input is acquired, and a second internal convert start
signal is generated, which initiates the conversion. This process
is repeated until all the selected voltage and auxiliary ADC inputs
have been converted.
None
Each voltage and auxiliary ADC input conversion requires a
minimum of 1 μs to acquire and convert the cell voltage or
auxiliary ADC input voltage. For example, when Bits[D15:D14]
CNVST
are set to 00, the falling edge of
triggers a series of 12
conversions. This requires a minimum of 12 μs to convert all
selected measurements on a single AD7280A. If no auxiliary
ADC input conversions are required, Bits[D15:D14] are set to
10. In this case, the conversion request triggers a series of six
conversions, requiring a minimum of 6 μs.
t1
CNVST
tACQ
tCONV
tCONV
INTERNAL ADC
CONVERSIONS
VOLT 6
VOLT 5
VOLT 4
AUX6
Figure 31. ADC Conversions on the AD7280A
CONVERSION WINDOW
t1
CNVST
tWAIT
tQUIET
INTERNAL ADC
CONVERSIONS
VOLT VOLT VOLT
VOLT VOLT
AUX6
6
5
4
6
5
SERIAL READ
OPERATION
DATA READBACK — ALL DEVICES
Figure 32. ADC Conversions and Readback on the AD7280A
Rev. 0 | Page 1± of 48
AD7280A
Note that 90 ꢁs should be allowed before initiating any conver-
sions following any change to Bits[D15:D14]. This time should
be allowed between writing to the control register to change the
selected conversions and initiating the first conversion.
Conversion Averaging
The AD7280A includes an option where the acquisition and
conversion of each cell input can be repeated with an averaged
conversion result being stored in the individual register. The
averaged conversion result can then be read back through the
SPI interface in the same manner as a standard conversion result.
The AD7280A can be programmed, through Bits[D10:D9] of the
control register, to complete one, two, four, or eight conversions.
The default on power-up is a single conversion per channel, that
is, no averaging.
CS
Conversions that are initiated by the rising edge of the
pin
require two separate write commands to the control register. The
first command configures the AD7280A for the required
acquisition time; the second command, following a delay of
CS
90 ꢁs, initiates the conversion on the rising edge of
.
After the completion of all requested conversions, the results
can be read back from either a single device or from all devices
in a daisy chain by using the SPI and daisy-chain interfaces. For
more information, see the Serial Interface section and the
Daisy-Chain Interface section.
Selection of the two, four, or eight average options through the
control register causes the control sequence of both the high
voltage and low voltage input multiplexers to be reconfigured to
allow the additional acquisitions and conversions to be completed.
In each case, the requested number of conversions is completed
on each channel before beginning the acquisition and conversion
of the next channel in sequence. For example, if an average of two
conversions is requested, the new sequence is Voltage Channel 6,
Voltage Channel 6, Voltage Channel 5, Voltage Channel 5, Voltage
Channel 4, and so on.
As shown in Figure 32, a wait time, tWA IT, is required between the
completion of conversions and the start of readback. This time
is required to synchronize the high speed conversion clock and
the lower speed clock used for all other AD7280A operations.
The minimum value of tWAIT is 5 ꢁs.
Acquisition Time
It should also be noted that when the high voltage multiplexer
is reconfigured, 90 ꢁs should be allowed before initiating any
conversions. This time should be allowed between writing to
the control register to select averaging and initiating the first
conversion. Conversions that are being initiated by the rising
The time required to acquire an input signal depends on how
quickly the sampling capacitor is charged. This, in turn, depends
on the input impedance and any external components placed on
the analog inputs. The default acquisition time of the AD7280A
on initial power-up is 400 ns. This time can be increased in steps
of 400 ns up to 1.6 μs to provide flexibility in selecting external
components on the analog inputs. The acquisition time is selected
by writing to Bits[D6:D5] in the control register (see Table 9).
CS
edge of the
pin require two separate write commands to the
control register. The first command configures the AD7280A
for the required averaging, and the second command, after a
CS
delay of 90 ꢁs, initiates the conversion on the rising edge of
.
Table 9. Analog Input Acquisition Time
Suggested External Component Configuration on
Analog Inputs
Bits[D6:D5]
Acquisition Time
00
01
10
11
400 ns
800 ns
1.2 μs
1.6 μs
As described in the Acquisition Time section, the acquisition
time of the AD7280A is selected by the status of Bits[D6:D5] in
the control register. This provides flexibility in selecting external
components on the analog inputs. A suggested configuration
for placing external components on the analog inputs to the
AD7280A is shown in Figure 33.
The acquisition time required is calculated using the following
formula:
t
ACQ = 10 × ((RSOURCE + R) × C)
where:
SOURCE should include any extra source impedance on the
analog input between the external capacitors (100 nF) and the
input pins. It does not include any extra source impedance, for
example, the 10 kΩ series resistors, which are between the
battery cells and the external capacitors.
R is the resistance seen by the track-and-hold amplifier looking
at the input, 300 Ω.
C is the sampling capacitance, that is, the value of the sampling
capacitor, 15 pF.
AD7280A
10kΩ
R
VIN6
100nF
10kΩ
VIN5
100nF
100nF
100nF
100nF
100nF
10kΩ
VIN4
VIN3
VIN2
10kΩ
10kΩ
10kΩ
10kΩ
VIN1
VIN0
Figure 33. External Series Resistance and Shunt Capacitance
Rev. 0 | Page 20 of 48
AD7280A
The 10 kΩ resistors in series with the inputs provide protection for
the analog inputs in the event of an overvoltage or undervoltage
on those inputs. The 100 nF capacitor across the differential inputs
acts as a low-pass filter in conjunction with the 10 kΩ resistor.
The cutoff frequency of the low-pass filter is 80 Hz. Using these
external components, the default acquisition time of 400 ns can
be used, which allows a combined acquisition and conversion
time of 1 μs.
device in the chain can be determined by multiplying tDELAY by
the number of slave AD7280As in the daisy chain. The total
conversion time for all cell voltage and auxiliary ADC input
conversions can be calculated using the following equation:
Total Conversion Time = ((tACQ + tCONV) × (Number of
Conversions per Part)) − tACQ + ((N − 1) × tDELAY
where:
ACQ is the analog input acquisition time of the AD7280A (see
Table 9).
CONV is the conversion time of the AD7280A, as specified in Table 3.
)
t
CONVERTING CELL VOLTAGES AND AUXILIARY
ADC INPUTS IN A CHAIN OF AD7280As
t
Number of Conversions per Part is the number of inputs selected
for conversion (6, 9, or 12, as listed in Table 8), multiplied by
the number of averages selected for each input (1, 2, 4, or 8).
N is the number of AD7280As in the daisy chain.
The AD7280A provides a daisy-chain interface that allows up to
eight parts to be stacked without the need for individual isola-
tion. One feature of the daisy-chain interface is the ability to
initiate conversions on all parts in the daisy-chain stack with a
single convert start command. The convert start command is
transferred up the daisy chain, from the master device to each
AD7280A in turn. The delay time between each AD7280A is
tDELAY, as shown in Figure 34. The maximum delay between the
start of conversions on the master AD7280A and the last AD7280A
t
DELAY is the delay time when transferring the convert start
command between adjacent AD7280A devices, as specified
in Table 3.
The total conversion times calculated for three possible
configurations of the AD7280A are included in Table 10.
TOTAL CONVERSION TIME =
tCONV) × (#CONVERSIONS PER PART)) – tACQ + ((N – 1) × tDELAY)
((tACQ
+
CNVST
tCONV
tACQ + tCONV
INTERNAL ADC
CONVERSIONS
PART 1
VOLT 6
VOLT 5
VOLT 4
AUX6
tDELAY
tDELAY
SERIAL READ
OPERATION
PART 2
VOLT 12
VOLT 11
VOLT 10
AUX12
tACQ + tCONV
tDELAY
tDELAY
SERIAL READ
OPERATION
PART 3
VOLT 18
VOLT 17
VOLT 16
AUX18
tACQ + tCONV
Figure 34. ADC Conversions and Readback on a Chain of Three AD7280As
Table 10. Calculated Conversion Times for Three Example AD7280A Configurations, TA = −40°C to +85°C
Bits
[D15:D14]
Bits
[D10:D9]
Bits
[D6:D5]
Conversion Total Conversion Time
Time per Part per 48 Channel Stack
Configuration
00
10
00
00
00
11
00
01
10
11
00
01
10
11
00
01
10
11
12 channels; tCONV = 6±5 ns; tACQ = 465 ns; average = 0
13.46 μs
15.2 μs
21.2 μs
26.15 μs
30.± μs
12 channels; tCONV = 6±5 ns; tACQ = 1.01 μs; average = 0 1±.45 μs
12 channels; tCONV = 6±5 ns; tACQ = 1.46 μs; average = 0 24.4 μs
12 channels; tCONV = 6±5 ns; tACQ = 1.8± μs; average = 0 2±.13 μs
6 channels; tCONV = 6±5 ns; tACQ = 465 ns; average = 0
6 channels; tCONV = 6±5 ns; tACQ = 1.01 μs; average = 0
6 channels; tCONV = 6±5 ns; tACQ = 1.46 μs; average = 0
6 channels; tCONV = 6±5 ns; tACQ = 1.8± μs; average = 0
12 channels; tCONV = 6±5 ns; tACQ = 465 ns; average = 8
12 channels; tCONV = 6±5 ns; tACQ = 1.01 μs; average = 8 162.67 μs
12 channels; tCONV = 6±5 ns; tACQ = 1.46 μs; average = 8 205.42 μs
12 channels; tCONV = 6±5 ns; tACQ = 1.8± μs; average = 8 246.27 μs
6.5 μs
8.23 μs
±.22 μs
11.47 μs
13.62 μs
110.± μs
10.±7 μs
13.22 μs
15.37 μs
112.65 μs
164.42 μs
207.17 μs
248.02 μs
Rev. 0 | Page 21 of 48
AD7280A
CONVERSION WINDOW
CONNECTION OF FEWER THAN SIX VOLTAGE CELLS
As described in the Converting Cell Voltages and Auxiliary
ADC Inputs section, the AD7280A converts the selected cell
voltage and auxiliary ADC inputs in a defined sequence (see
Figure 31). As described in the Circuit Information section,
the AD7280A consists primarily of a high voltage input multi-
plexer, a low voltage input multiplexer, and a SAR ADC. The six
cell voltage channels are presented to the ADC in turn by the high
voltage multiplexer. Control is then handed to the low voltage
multiplexer that allows the six auxiliary ADC channels to be
converted. Following completion of all selected conversions,
control is handed back to the high voltage multiplexer, and the
AD7280A is ready to receive the next valid convert start command.
The AD7280A provides six input channels for battery cell voltage
measurement. The AD7280A can also be used in applications
that require fewer than six voltage measurements. In these appli-
cations, care should be taken to ensure that the sum of the
individual cell voltages still exceeds the minimum VDD supply
voltage. For this reason, the recommended minimum number of
battery cells connected to each AD7280A is 4. Care should also
be taken to ensure that the voltage on the VIN6 input is always
greater than or equal to the voltage on the VDD supply pin. For
example, in an application with five battery cells connected to
the AD7280A, the cell voltage on Cell 5 should be applied across
VIN6 and VIN5, and the VIN4 and VIN5 inputs should be shorted
together. Figure 35 shows an example of the battery connections
to the AD7280A in a four-cell battery monitoring application.
The conversion window of the AD7280A includes the actual con-
version time for the selected channels (see Table 10), as well as
the additional time required to return control to the high
voltage multiplexer and configure it to start acquiring the cell
voltage between VIN6 and VIN5. The conversion window
defines the minimum time that should be allowed between
successive convert start commands.
AD7280A
VIN6
VIN5
10kΩ
VIN4
100nF
10kΩ
VIN3
100nF
100nF
100nF
10kΩ
10kΩ
10kΩ
The conversion window for the AD7280A can be calculated
using the following equation:
VIN2
VIN1
VIN0
Conversion Window = Total Conversion Time + 80 μs
where Total Conversion Time can be calculated for either a
single device or for a chain of devices, as described in the
Converting Cell Voltages and Auxiliary ADC Inputs section.
Figure 35. Typical Connections for a Four-Cell Application
SELF-TEST CONVERSION
Regardless of how many cell voltage measurements are required
in the user application, the AD7280A acquires and converts the
voltages on all six cell voltage input channels. The conversion data
on all six voltage channels is supplied to the DSP/microprocessor
using the SPI/daisy-chain interfaces. Users should ignore the
conversion data that is not required in their application.
A self-test conversion can be initiated on the AD7280A, which
allows the operation of the ADC and reference buffer to be
verified. The self-test conversion is completed on the internal
1.2 V band gap reference voltage, and the voltage range for the
conversion is 0 V to 5 V. The self-test conversion can be initi-
ated on either a single AD7280A or on all AD7280As in the
daisy chain simultaneously.
It is also possible to read back a single cell voltage conversion
result from each device in the daisy chain. This can be done by
programming the read register on each device to read back the
required conversion result (see Example 4 in the Examples of
Interfacing with the AD7280A section). However, as previously
described, all six cell voltage channels are converted. When
using the device in this mode, the overall conversion sample
rate should be limited by the conversion window required for
the number of channels selected by Bits[D15:D14] of the
control register.
The conversion results can be read back though the read protocols
defined in the Serial Interface section. The self-test conversion
result typically varies between Code 970 and Code 990.
The self-test conversion can also be used to verify the operation
of the alert outputs, as described in the Alert Output section.
When using the alert function, the user should program the alert
register to ensure that the shorted channels do not incorrectly
trigger an alert output (see the Alert Output section).
Rev. 0 | Page 22 of 48
AD7280A
AUXILIARY ADC INPUTS
AD7280A
V
SS
R
The AD7280A provides six single-ended analog inputs to the
ADC—AUX1 to AUX6—which can be used to convert the
voltage output of a thermistor temperature measurement circuit.
In the event that no temperature measurements are required or
that individual cell temperature measurements are not required,
the auxiliary ADC inputs can be used to convert any other 0 V
to 5 V input signal.
TERM
AUX
TERM
AUX1
AUX2
AUX3
AUX4
AUX5
The AD7280A can be programmed to complete conversions on
all six auxiliary ADC channels, on three auxiliary ADC channels
(AUX1, AUX3, and AUX5), or on none of the auxiliary ADC
input channels. The number of conversions is programmed
through Bits[D15:D14] of the control register. The number of
conversion results supplied by the AD7280A for readback by
the DSP/microprocessor is programmed through Bits[D13:D12]
of the control register. It is also possible to read back a single
auxiliary ADC conversion result from each device in the daisy
chain. This can be done by programming the read register on
each device to read back the required conversion result (see
Example 4 in the Examples of Interfacing with the AD7280A
section). If the device is used in this mode, the overall conversion
sample rate should be limited by the conversion window required
for the number of channels selected by Bits[D15:D14] of the
control register.
AUX6
V
REG
Figure 36. Typical Circuit Using the Thermistor Termination Resistor
POWER REQUIREMENTS
The current consumed by the AD7280A in normal operation,
that is, when not in power-down mode, is dependent on the
mode in which the part is being operated. The three distinct
modes of operation can be described as follows:
•
•
•
Voltage and auxiliary ADC input conversion
AD7280A configuration and data readback
Cell balancing
The AD7280A consumes its highest level of current while con-
verting voltage and/or auxiliary ADC inputs to digital outputs.
Depending on the configuration of the AD7280A, the conversion
time can be as little as 6 μs. The typical current required by the
AD7280A during conversion is 6.9 mA (see Table 2).
In an application where the alert function is used but only one
or two auxiliary ADC inputs are required, the AD7280A should
first be programmed to complete and read back only three
auxiliary ADC conversions by setting Bits[D15:D12] of the
control register to 0101. Channel AUX5 and Channel AUX3 can
be removed from the alert detection by writing to Bits[D1:D0]
of the alert register (see Table 12 in the Alert Output section).
When configuring a chain of AD7280As or when reading back
the voltage and/or auxiliary ADC conversion results from a chain
of AD7280As, the current required for each AD7280A is typically
6.5 mA (see Table 2). The time required to read back the voltage
conversions results from 48 lithium ion cells depends on the
speed of the interface clock used, that is, SCLK, but it can be as
low as 1.54 ms.
Thermistor Termination Input
If thermistor circuits are used to measure each individual cell
temperature, the thermistor termination pin, AUXTERM, can be
used to terminate the thermistor inputs for each auxiliary ADC
input measurement. This reduces the termination resistor
requirement from six resistors to one. Bit D3 in the control
register should be set to 1 when using the AUXTERM input.
The typical current consumed by the AD7280A when the cell
balance outputs are switched on is 6.4 mA (see Table 2). The
length of time for which the cell balance outputs are switched
on is defined by the user.
When the AD7280A is not being used in any of the aforemen-
tioned modes of operation, it is recommended that the device
be powered down, as described in the Power-Down section.
This significantly reduces the current drawn by each AD7280A
in the chain, which avoids unnecessary draining of the lithium
ion cells and aids in current matching between devices across
the full battery stack.
Note that, due to settling time requirements, the thermistor termi-
nation resistor option should only be used when the acquisition
time of the AD7280A is set to its highest value (1.6 μs). The
acquisition time is configured by setting Bits[D6:D5] of the
control register (see Table 9).
In Figure 36, the termination resistor is placed between VSS
and AUXTERM. The AUXTERM input can be used to terminate the
thermistor inputs to the high or low voltage of the thermistor
circuit.
Rev. 0 | Page 23 of 48
AD7280A
V
DD
POWER-DOWN
0.1µF
10µF
10kΩ
The AD7280A provides two power-down options.
•
•
Full power-down (hardware)
Software power-down
V
MASTER
DD
V
REG
1µF
DV
AV
CC
CC
0.1µF
0.1µF
Full Power-Down (Hardware)
The AD7280A can be placed into full power-down mode, which
V
DRIVE
PD
requires only 5 μA maximum current, by taking the
PD
pin low.
AD7280A
V
REF
The falling edge of the
digital circuitry.
pin powers down all analog and
MUST GO TO 0V
IN HARDWARE
POWER-DOWN
1µF
0.1µF
C
REF
PD
The AD7280A includes a digital delay filter on the
pin,
AUX
TERM
which protects against a power-down being initiated by noise
PD
ALERT
SDO
SDI
AUX6
AUX5
AUX4
AUX3
AUX2
AUX1
or glitches on the hardware
pin. A hardware power-down
pin is held low for approximately
130 ꢁs. Similarly, the AD7280A is not taken out of power-down
PD
DSP/MICRO-
PROCESSOR
PD
is not initiated until the
SCLK
CS
PD
mode until the
pin is held high for approximately 130 ꢁs.
CNVST
The digital delay filter does not apply on initial power-up. The
power-on request is accepted by the AD7280A approximately
V
SS
MUST GO TO 0V IN
HARDWARE POWER-DOWN
PD
5 ꢁs after the rising edge of
.
Figure 37. VDRIVE Powered from VREG
When placing the AD7280A into full power-down mode, AVCC
and DVCC must fall to 0 V and must not be held high by any
external means. AVCC and DVCC can be held high unintention-
ally if the auxiliary ADC inputs are greater than the forward
bias on the internal ESD protection diodes. For this reason, it
is recommended that the auxiliary ADC inputs return to 0 V
when the part is placed in full power-down mode.
V
DD
0.1µF
10µF
10kΩ
V
MASTER
V
REG
DD
1µF
0.1µF
0.1µF
2.7V TO 5.5V SUPPLY
DV
AV
CC
CC
In addition, all digital inputs on the AD7280A master device
must return to 0 V when the part is placed in full power-down
mode (see Figure 37). However, if an external VDRIVE supply is
used—that is, VDRIVE is not connected to VREG—then only the
AD7280A
V
DRIVE
0.1µF
10µF
MUST GO TO 0V
IN HARDWARE
POWER-DOWN
line must return low (see Figure 38).
CNVST
V
REF
1µF
0.1µF
C
When the AD7280A is placed into full power-down mode, the
device must be left in full power-down for a minimum of 2 ms
when the VREG and VREF pins are decoupled with 1 ꢁF capacitors.
This ensures that the charge on the VREG and VREF decoupling
capacitors dissipates sufficiently to allow the internal power-on
reset circuit to activate when powering the AD7280A back up.
REF
AUX
TERM
ALERT
SDO
SDI
AUX6
AUX5
AUX4
AUX3
AUX2
AUX1
DSP/MICRO-
PROCESSOR
SCLK
CS
PD
PD
CNVST
This time is measured from the falling edge of the
pin.
V
SS
Figure 18 shows a plot of the voltage on the VREG and VREF pins
as the AD7280A is powering down with 1 ꢁF decoupling
capacitors on the pins. Figure 20 shows a similar plot but with
10 ꢁF decoupling capacitors on the VREG and VREF pins.
MUST GO TO 0V IN
HARDWARE POWER-DOWN
Figure 38. VDRIVE Powered from DSP/Microprocessor
Rev. 0 | Page 24 of 48
AD7280A
Software Power-Down
CELL BALANCING OUTPUTS
The AD7280A can be placed into software power-down mode,
which requires 3.8 mA of current, by setting Bit D8 in the
The AD7280A provides six cell balance outputs that can be used
to drive the gate of external transistors as part of a cell balancing
circuit. Each CBx output can be set to provide either a 0 V or 5 V
output with respect to the absolute amplitude of the negative
terminal of the battery cell that is being balanced. For example,
the CB6 output provides a 0 V or 5 V output with respect to the
voltage on the VIN5 analog input. The CBx outputs are set by
writing to the cell balance register. The default value of the cell
balance register on power-up is 0x00.
CNVST
control register through the serial interface. The
pin
should be gated out before generating a software power-down
CNVST
(see the
Control Register section). When the AD7280A
is powered down through the serial interface, the regulator, the
reference, and the daisy-chain circuitry stay powered up, but the
remaining analog and digital circuitry is powered down. This is
necessary to ensure that the signal to power on the part, or the
chain of parts, is correctly received.
VIN6
Power-Down Timer
10kΩ
The PD timer register allows the user to program a set time after
which the AD7280A is automatically powered down. This timer
CB6
VIN5
PD
functions as a time delay between the falling edge of the
10kΩ
input (or the setting of Bit D8 in the control register) and the
AD7280A powering down. The PD timer can be set to a value
from 0 minutes to 36.9 minutes, with a resolution of 71.5 sec.
The user should first write to the PD timer register to define the
CB5
VIN4
AD7280A
10kΩ
CB4
PD
desired delay. Any subsequent falling edge on the
input or
VIN3
setting of Bit D8 in the control register starts the PD timer.
When the programmed time elapses, the AD7280A checks the
10kΩ
CB3
VIN2
PD
PD
state of the
pin. If the
pin is low, the AD7280A powers
10kΩ
PD
down. If the
pin is high, the part does not power down and
CB2
continues to operate as normal. The default value of the PD
timer register on power-up is 0x00.
VIN1
10kΩ
CB1
If the PD timer register is written to after the counter starts,
the counter is reset to 0. The count then restarts automatically,
without further input from the user, and counts to the new value
in the PD timer register. If the new time in the PD timer register
VIN0
Figure 39. Cell Balancing Configuration
PD
is 0, the part checks the state of the
pin and powers down if
pin is low. Note that when the PD timer is activated—for
PD
As noted in the Power-Down Timer section, a power-down timer
can be programmed on the AD7280A. This timer can be used
to allow cell balancing to occur for a set time before powering
down the AD7280A. The power-down timer is independent of
the cell balance timers. If no power-down timer is set—that is, if
the PD timer register is at its default value of 0x00—a falling edge
PD
the
example, by a falling edge on the
PD
pin—a subsequent rising
pin does not disable the active PD timer. It is
edge on the
PD
recommended that the
timer expires.
pin be held low until an active PD
PD
on the
pin switches off the CBx outputs and powers down the
POWER-UP TIME
AD7280A. If a power-down timer is set, the CBx outputs are
powered down when the programmed power-down timer elapses
and the AD7280A is powered down.
As described in the Power-Down section, a full power-down
PD
of the AD7280A (active low on the
input) powers down all
analog and digital circuitry. The recommended power-up time
from hardware power-down, when the internal reference is
decoupled with a 1 μF capacitor, is 5.5 ms. It is recommended
that no conversions be initiated until the 5.5 ms power-up time
elapses because such conversions can result in inaccurate data.
In an application with two or more AD7280A devices in a daisy
chain, it is recommended that series resistors be placed between
the CBx outputs of the AD7280A and the gates of the external
cell balancing transistors. These resistors are recommended to
protect the AD7280A in the event that the external cell balancing
transistors are damaged during the initial connection of the
monitoring circuitry to the battery stack. Consideration should
also be given to the protection of these external transistors
during the initial connection of the monitoring circuitry to the
battery stack.
A software power-down powers down all analog and digital
circuitry on the AD7280A except for the regulator, the 1.2 V
band gap reference, and the daisy-chain circuitry. The recom-
mended power-up time from software power-down, when the
VREF pin is decoupled with a 1 μF capacitor, is 1 ms.
Rev. 0 | Page 25 of 48
AD7280A
An example of how damage to the external transistors can occur
is a connection sequence that first provides the system ground
(the ground supply to the master AD7280A in the daisy chain)
followed by a connection from any of the battery cells at a
potential high enough to exceed the VGS of the cell balancing
transistor, for example 40 V. If these two connections are the
first battery connections made in the system, the result is 40 V
being applied to one of the VINx pins of the AD7280A through
a series resistor. The 40 V battery connection is also directly
applied to the source input of one of the cell balancing transistors.
However, because no power has been supplied to the VDD pin of
the AD7280A, all the CBx outputs are at 0 V. This results in a
reverse voltage of 40 V across the VGS of the external transistor,
which can damage the device.
Programming the Cell Balance Timers
It is recommended that the required CBx timer values be
programmed to each individual CBx timer register before
activating the CB counter. Changing the CBx timer values while
the counter is running is possible; however, writing to an active
CBx timer register resets the counter, as described in the Cell
Balance Timers section.
Cell Balance Timer Example 1
The following sequence of steps programs a value of 214.5 sec
to the CB1 and CB2 timer registers.
1. Set Bits[D4:D3] of the CB1 timer register and the CB2
timer register high.
2. Set Bits[D3:D2] of the cell balance register high.
3. Wait 60 sec.
Cell Balance Timers
4. Set Bits[D4:D3] of the CB3 timer register high.
5. Set Bits[D4:D2] of the cell balance register high.
The AD7280A offers six cell balance timer registers that allow
the on time of each CBx output to be programmed. The CBx
timers can be set to a value from 0 minutes to 36.9 minutes. The
resolution of the CBx timers is 71.5 sec. A value of 0x00 in a
CBx timer register means that the timer is not activated. A non-
zero value programmed to a CBx timer register configures the
CBx timer for use, but the CBx outputs and the CBx timers are
not activated until the cell balance register is written to. At the
end of the individually programmed CBx time, the respective
CBx output returns to its default state of 0 V output with respect
to the absolute amplitude of the negative terminal of the battery
cell that is being balanced. Also at this time, the cell balance
register is reset and the CBx timer registers continue to hold
their programmed values. The default value of the CBx timer
registers on power-up is 0x00.
In this example, the CB1 and CB2 outputs are switched on and
the cell balance counter is activated. Following the 60 sec wait,
a value of 214.5 sec is written to the CB3 timer register, the CB3
output is switched on, and the on state of the CB1 and CB2
outputs is maintained. In this example, all three CB outputs are
switched off at the same time (214.5 sec). This is because the CB
counter was already active before the CB3 timer register was
programmed and the CB3 output selected.
Cell Balance Timer Example 2
In this example, follow the same sequence of steps described in
the Cell Balance Timer Example 1 section, but increase the wait
step from 60 sec to any value greater than 214.5 sec.
The initial steps set up the CB1 and CB2 timers and activate the
CB1 and CB2 outputs. However, because the wait state is now
longer than the time programmed to the CB1 and CB2 timers,
the CB1 and CB2 timers expire before the additional writes to
configure CB3. The CB1 and CB2 outputs switch off, a 0 is
written to Bits[D3:D2] of the cell balance register, and the CB
counter is reset to 0x00 before the commands to program the
CB3 timer and to switch on the CB3 output are received.
When using the cell balance timer feature, note that the timer on
each cell balance output is operated from a single CB counter.
When a nonzero value is programmed to any CBx timer register,
this counter is activated by writing a nonzero value to the cell
balance register. The current value of the counter is compared
to the values programmed to each CBx timer register at 4.5 sec
intervals (71.5 sec/16). When the value in the counter reaches
the value in the CBx timer register, the cell balance output
corresponding to that CBx timer register is switched off. Note
that the cell balance register has a higher priority than the CBx
timer registers. A CBx output can be switched off by writing to
the cell balance register even if the value programmed to the
respective CBx timer register has not expired.
In this example, the second write to the cell balance registers—
which selects the CB1, CB2, and CB3 outputs—is considered a
new activation of the CB counter. The CB1, CB2, and CB3
outputs switch on and, if no further commands are written to
the AD7280A, all three outputs switch off 214.5 sec after this
second activation of the CB counter.
Writing a zero or a nonzero value to an active CBx timer
register (corresponding CB output switched on) results in the
cell balance counter being reset and automatically restarted.
Note that overwriting the CBx timer with 0 restarts the counter,
but, because the timer value is now 0, the corresponding CB
output is switched off. Any write to a nonactive CBx timer
register (corresponding CB output not switched on) has no
effect on the cell balance counter.
Rev. 0 | Page 26 of 48
AD7280A
Table 12. Alert Register Settings, Bits[D3:D0]1
Bits[D3:D2] Bits[D1:D0] Action
ALERT OUTPUT
The alert output on the AD7280A can be used to indicate
whether any of the following faults has occurred:
00
01
10
XX
XX
XX
Includes all six voltage channels in
alert detection (default)
Removes VIN5 from alert
detection
Removes VIN5 and VIN4 from alert
detection
•
•
•
•
Cell overvoltage
Cell undervoltage
Auxiliary ADC overvoltage
Auxiliary ADC undervoltage
11
XX
XX
00
Reserved
Following each completed conversion, the cell voltage and
auxiliary ADC measurement results are compared to the alert
thresholds. The alert thresholds are set by writing to the cell
overvoltage, cell undervoltage, AUX ADC overvoltage, and
AUX ADC undervoltage registers. An alert output is generated
if the cell voltage and/or the auxiliary ADC results are outside
the programmed alert thresholds.
Includes all AUX ADC channels
selected for conversion in alert
detection2 (default)
XX
XX
01
10
11
Removes AUX5 from alert
detection3
Removes AUX5 and AUX3 from
alert detection3
XX
Reserved
The alert output can be configured as a static or dynamic output
by writing to the alert register. The static alert output is a high
signal that is pulled low in the event of an overvoltage or under-
voltage on the cell voltage or auxiliary ADC input conversions.
The dynamic alert is a square wave that can be programmed to
a frequency of 100 Hz, 1 kHz, or 10 kHz. The alert output can
be used as part of a daisy chain, in which case the AD7280A at
the top of the chain, that is, farthest away from the DSP/micro-
processor, should be programmed to generate the initial alert
output, and all other devices in the chain should be programmed
to allow the alert signal to pass through. If a conversion result
outside the programmed thresholds occurs, either on the device
generating the initial alert signal or on any device in the chain,
the alert signal is pulled low to indicate that an alert condition
has occurred. At the end of the daisy chain, the master AD7280A,
which is connected to the DSP/microprocessor, takes the alert
signal from the chain and passes it in standard digital voltage
format to the DSP/microprocessor. The configuration settings
for the alert register are described in Table 11 and Table 12.
1 X is don’t care.
2 Includes six auxiliary ADC channels in the alert detection if conversions on
six auxiliary ADC channels are selected in the control register; includes three
auxiliary ADC channels in the alert detection if conversions on three auxiliary
ADC channels are selected in the control register.
3 To remove AUX5 or AUX5 and AUX3 from the alert detection, conversions on
three auxiliary ADC input channels only must be selected in the control register.
Some applications require fewer than six voltage measurements
(see the Connection of Fewer Than Six Voltage Cells section).
As shown in Figure 35, it is recommended that a channel that
is not being used on the AD7280A be shorted to the channel
below it. To prevent the incorrect triggering of the alert output
in this application, the AD7280A allows the user to select up to
two voltage channels that can be taken out of the overvoltage/
undervoltage detection circuit. This is programmed through
Bits[D3:D2] of the alert register. The user can also remove all
or selected auxiliary ADC channels from the detection circuit.
This is programmed through Bits[D1:D0] of the alert register in
combination with Bits[D15:D14] of the control register.
The operation of the alert output can be verified by initiating a
self-test conversion. The self-test conversion converts the band
gap reference voltage, 1.2 V, which triggers an alert output if the
cell undervoltage threshold is set higher than 1.2 V. To test the
alert output, a self-test conversion should be initiated on the
AD7280A farthest away from the DSP/microprocessor.
Table 11. Alert Register Settings, Bits[D7:D4]1
Bits[D7:D6]
Bits[D5:D4]
Action
00
XX
No alert signal generated or
passed (default)
01
10
10
10
XX
00
01
10
Generates a static (high) alert
signal to be passed down the
daisy chain
Generates a 100 Hz square wave
alert signal to be passed down
the daisy chain
Generates a 1 kHz square wave
alert signal to be passed down
the daisy chain
Generates a 10 kHz square wave
alert signal to be passed down
the daisy chain
The operation of the alert output can also be verified by increas-
ing or decreasing the thresholds around a known input voltage
to trigger an alert condition. The alert operation of each device
in the daisy chain of AD7280As can be verified by, for example,
decreasing the cell overvoltage threshold of that device below the
value of the input voltage on the cells. Initiating a conversion on
all devices in the daisy chain pulls the alert signal low as it passes
through that device. The relevant threshold on that device can
then be returned to its previous value and the process repeated
on the next device in the daisy chain.
10
11
11
XX
Reserved
Passes an alert signal from the
AD7280A at higher potential in
the daisy chain
1 X is don’t care.
Rev. 0 | Page 27 of 48
AD7280A
REGISTER MAP
Table 13.
Table 14. Control Register Settings
Register
Address
Register
Data
Read/Write
Register
Bits
Description
Register Name
Cell Voltage 1
Cell Voltage 2
Cell Voltage 3
Cell Voltage 4
Cell Voltage 5
Cell Voltage 6
AUX ADC 1
AUX ADC 2
AUX ADC 3
AUX ADC 4
AUX ADC 5
AUX ADC 6
Self-Test
[D15:D14]
Select conversion inputs
00 = six cell voltages and six AUX ADCs (default)
01 = six cell voltages and AUX1, AUX3, and AUX5
10 = six cell voltages only
11 = ADC self-test
Read conversion results
00 = six voltages and six AUX ADCs (default)
01 = six voltages and AUX1, AUX3, and AUX5
10 = six cell voltages only
11 = no-read operation
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x0±
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D11 to D0 Read only
D15 to D8 Read/write
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
D7 to D0
[D13:D12]
D11
Conversion start format
0 = falling edge of CNVST input (default)
1 = rising edge of CS
[D10:D±]
Conversion averaging
00 = single conversion only (default)
01 = average by 2
10 = average by 4
11 = average by 8
Control
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Cell Overvoltage
Cell Undervoltage
AUX ADC Overvoltage 0x11
AUX ADC Undervoltage 0x12
D8
Power-down format
0 = falling edge of PD input (default)
1 = software power-down
Software reset
0 = take the AD7280A out of reset (default)
1 = reset the AD7280A
Set acquisition time
00 = 400 ns (default)
01 = 800 ns
10 = 1.2 μs
Alert
0x13
0x14
0x15
0x16
0x17
0x18
0x1±
0x1A
0x1B
0x1C
0x1D
Cell Balance
CB1 Timer
CB2 Timer
CB3 Timer
CB4 Timer
CB5 Timer
CB6 Timer
PD Timer
Read
D7
[D6:D5]
11 = 1.6 μs
Reserved; set to 1
D4
D3
CNVST Control
Thermistor termination resistor
0 = function not in use (default)
1 = termination resistor connected
Lock device address
0 = does not lock to new device address; continues
to operate with Device Address 0x00 (default)
1 = part locks to new device address that it is
presented with
Increment device address
0 = does not increment the device address when
transferring data up the daisy chain
1 = increments the device address when
transferring data up the daisy chain (default)
Daisy-chain register readback
CELL VOLTAGE REGISTERS
The cell voltage registers store the conversion result from each cell
input. The conversion result is in 12-bit straight binary format.
D2
D1
D0
AUXILIARY ADC REGISTERS
The AUX ADC registers store the conversion result from each
auxiliary ADC input. The conversion result is in 12-bit straight
binary format.
SELF-TEST REGISTER
The self-test register stores the conversion result of the ADC
self-test. The conversion result is in 12-bit straight binary format.
CONTROL REGISTER
0 = function not in use; registers are read in single
register readback mode
1 = set daisy chain for register readback (default)
The control register is a 16-bit register that is used to configure
the AD7280A. Table 14 describes the operation of each bit in
the control register.
Rev. 0 | Page 28 of 48
AD7280A
Select Conversion Inputs
Thermistor Termination Resistor
Bits[D15:D14] of the control register determine which cell
voltages and auxiliary ADC inputs are converted following a
convert start command. The default value of D15 and D14 on
power-up is 00.
Bit D3 of the control register should be set if the user wishes to
use a single thermistor termination resistor on the AUXTERM pin.
Note that, due to settling time requirements, the thermistor
termination resistor option should only be used when the acqui-
sition time of the AD7280A is set to its highest value, that is,
1.6 μs (set Bits[D6:D5] to 11). The default value of D3 is 0.
Read Conversion Results
Bits[D13:D12] of the control register determine which cell
voltage and auxiliary ADC conversion results are supplied to
the serial or daisy-chain data output pins for readback. The
default value of D13 and D12 on power-up is 00.
Lock Device Address
Bit D2 of the control register is used in conjunction with Bit D1
to allow individual device addresses for each AD7280A in the
daisy chain to be defined and locked to the part. Bit D1 is used
to generate the individual device addresses that are presented to
each AD7280A in the daisy chain in the form of a write command.
When Bit D2 is set high, the AD7280A locks to the device address
presented to it. This new device address is used for all subsequent
CRC calculations. When Bit D2 is set low, the device address of
the AD7280A is not locked. In this case, a device address of 0x00
is used for CRC calculations. The default value of D2 is 0.
Conversion Start Format
A conversion on the AD7280A can be initiated through the
CNVST
hardware
command. Bit D11 of the control register determines whether a
CNVST
pin or by issuing a software convert start
conversion is initiated on the falling edge of the
input
input. The default format on
pin, that is, 0. When using the rising
input to initiate conversions, Bit D11 is reset to
CS
or on the rising edge of the
CNVST
edge of the
power-up is the
CS
Increment Device Address
0 following the initiation of conversions.
Bit D1 of the control register determines whether the AD7280A
increments the device address that it receives as part of a write
command when transferring that command up the daisy chain.
When Bit D1 is set to 1, the device address is incremented as the
command is passed up the chain. This mode of operation is used
on initial power-up and when coming out of a hardware power-
down to allow individual device addresses for each AD7280A in
the daisy-chain stack to be defined. When D1 is set low, no change
is made to the device address as the command is passed up the
chain. The default value of D1 is 1.
Conversion Averaging
Bits[D10:D9] of the control register determine the number of
conversions completed on each input with the averaged results
stored in the relevant result registers. The user can select a single
conversion only or the average of two, four, or eight conversions.
The default value of Bits[D10:D9] on power-up is 00, that is,
single conversion only.
Power-Down Format
Setting Bit D8 of the control register places the AD7280A into
software power-down. See the Power-Down section for more
information. The default value of Bit D8 on power-up is 0.
Daisy-Chain Register Readback
Bit D0 of the control register enables the readback of individual
registers from each AD7280A in a daisy chain. When Bit D0 is
set high, the application of sufficient clocks allows the data stored
in the register address identified by the read register to be shifted
out of each AD7280A in turn. This data is passed down the daisy
chain and read back by the DSP/microprocessor. When Bit D0
is set low, daisy-chain read is disabled. See the Daisy-Chain
Interface section and the Examples of Interfacing with the
AD7280A section. The default value of D0 is 1.
Software Reset
Bit D7 of the control register allows the user to initiate a software
reset of the AD7280A. Two write commands are required to
complete the reset operation. Bit D7 must be set high to put the
AD7280A into reset. Bit D7 must then be set low to take the
AD7280A out of reset. A software reset resets all user configurable
registers to their default values with the exception of the lower
byte of the control register (Address 0x0E). When executing a
software reset, care should be taken to ensure that Bits[D6:D0]
are not incorrectly overwritten.
CELL OVERVOLTAGE REGISTER
The cell overvoltage register determines the high voltage thresh-
old of the AD7280A. Cell voltage conversions that exceed the
overvoltage threshold trigger the alert output. The AD7280A
allows the user to set the overvoltage threshold to a value from
1 V to 5 V. The resolution of the overvoltage threshold is eight
bits, that is, 16 mV. The default value of the overvoltage threshold
on power-up is 0xFF (5 V).
Set Acquisition Time
Bits[D6:D5] of the control register determine the acquisition
time of the ADC. See the Acquisition Time section for more
information. The default value of the acquisition time is 400 ns,
that is, 00.
Rev. 0 | Page 2± of 48
AD7280A
CELL UNDERVOLTAGE REGISTER
CELL BALANCE REGISTER
The cell undervoltage register determines the low voltage thresh-
old of the AD7280A. Cell voltage conversions lower than the
undervoltage threshold trigger the alert output. The AD7280A
allows the user to set the undervoltage threshold to a value from
1 V to 5 V. The resolution of the undervoltage threshold is eight
bits, that is, 16 mV. The default value of the undervoltage threshold
on power-up is 0x00 (1 V).
The cell balance register determines the status of the six cell
balance outputs. The six CBx outputs are set by writing to
Bits[D7:D2] of the cell balance register. The cell balance register
is reset by a software reset or following a hardware power-down.
The default value of the cell balance register on power-up is 0x00.
Table 15. Cell Balance Register Settings
Bits
Description
AUX ADC OVERVOLTAGE REGISTER
D7
Set CB6 output
0 = output off
1 = output on
Set CB5 output
0 = output off
1 = output on
Set CB4 output
0 = output off
1 = output on
Set CB3 output
0 = output off
1 = output on
Set CB2 output
0 = output off
1 = output on
Set CB1 output
0 = output off
1 = output on
Reserved; set to 0
The AUX ADC overvoltage register determines the high voltage
threshold of the AD7280A auxiliary ADC inputs. Conversions
that exceed this threshold trigger the alert output. The AD7280A
allows the user to set the threshold to a value from 0 V to 5 V. The
resolution is eight bits, that is, 19 mV. The default value of the
auxiliary ADC overvoltage threshold on power-up is 0xFF (5 V).
D6
D5
AUX ADC UNDERVOLTAGE REGISTER
The AUX ADC undervoltage register determines the low voltage
threshold of the AD7280A auxiliary ADC inputs. Conversions
that are lower than this threshold trigger the alert output. The
AD7280A allows the user to set the threshold to a value from 0 V
to 5 V. The resolution is eight bits, that is, 19 mV. The default
value of the AUX ADC undervoltage threshold on power-up
is 0x00 (0 V).
D4
D3
D2
ALERT REGISTER
The alert register determines the configuration of the alert
function. The alert can be configured as a static or dynamic
signal.
[D1:D0]
CBx TIMER REGISTERS
•
The static signal is a high signal that is pulled low to
indicate that an overvoltage or undervoltage on a cell
or on the auxiliary ADC has occurred.
The dynamic signal is a square wave, the frequency
of which can be set to 100 Hz, 1 kHz, or 10 kHz.
The CBx timer registers allow the user to program individual times
for each cell balance output. The AD7280A allows the user to set
the CBx timer to a value from 0 minutes to 36.9 minutes. The
resolution of the CBx timers is 71.5 sec. The default value of the
CBx timer registers on power-up is 0x00. When the CBx timer
value is set to 0x00, the CBx timer is not activated; that is, the CBx
outputs are all controlled by the contents of the cell balance
register only. For more information, see the Cell Balancing
Outputs section.
•
When a number of AD7280As are operating in daisy-chain
mode, the selection of static or dynamic alert is set on the
AD7280A at the highest potential in the chain only. The alert
registers on the remaining AD7280As in the chain should be
programmed to pass the alert signal through the chain. Each
part passes the static or dynamic alert signal through the chain
or pulls the signal low to indicate that an overvoltage or under-
voltage on a cell or on the auxiliary ADC has occurred.
Table 16. CBx Timer Register Settings
Bits
Description
[D7:D3]
5-bit binary code to set the CB timer to a value
from 0 minutes to 36.± minutes
[D2:D0]
Reserved; set to 000
See Table 11 and Table 12 for more information about the alert
register settings. The default value of the alert register on
power-up is 0x00.
Rev. 0 | Page 30 of 48
AD7280A
PD TIMER REGISTER
CNVST CONTROL REGISTER
The PD timer register allows the user to configure a set time
after which the AD7280A is automatically powered down. The
AD7280A allows the user to set the PD timer to a value from
0 minutes to 36.9 minutes. The resolution of the PD timer is
71.5 sec. When using the PD timer in conjunction with the CBx
timers, the value programmed to the PD timer should exceed
that programmed to the CBx timer by at least 71.5 sec because
the PD timer takes priority over the CBx timers. The default
value of the PD timer register on power-up is 0x00.
CNVST
The
signal from the
CNVST
control register allows the user to gate the input
CNVST
pin.
Bit D0 of the
control register allows the user to hold the
signal high regardless of any external noise or
CNVST
internal
CNVST
glitches on the
pin. This setting can be used in noisy
environments to prevent incorrect initiation of conversions.
When using the rising edge of to perform a software convert
CS
start, it is recommended that the
pin be gated out by
CNVST
setting Bit D0 high (see the Conversion Start Format section).
Table 17. PD Timer Register Settings
CNVST
window in the
Bit D1 of the
control register allows the user to open a
CNVST CNVST
Bits
Description
gate that allows a single
pulse
[D7:D3]
5-bit binary code to set the PD timer to a value
from 0 minutes to 36.± minutes
through. The window is closed automatically following a falling
CNVST
edge on the
should write 10 to Bits[D1:D0] of the
immediately before each conversion start request.
pin. To use this functionality, the user
[D2:D0]
Reserved; set to 000
CNVST
control register
READ REGISTER
The read register, in conjunction with Bits[D13:D12] and
Bit D0 of the control register, defines the read operations of the
AD7280A. To read back a single register from either a single
AD7280A or from a chain of AD7280A devices, the desired
register address should first be written to the read register. To
read back a series of conversion results from either a single
AD7280A or from a chain of AD7280A devices, an address of
0x00 should be written to the read register. The default value of
the read register on power-up is 0x00.
CNVST
The default value of the
is 0x00.
control register on power-up
CNVST
Table 19.
Control Register Settings
Bits
[D7:D2]
Bit
D1
Bit
D0
Description
000000
000000
000000
0
X
1
0
CNVST input not gated (default).
CNVST input gated.
1
0
Allow single CNVST pulse.
Additional CNVST pulses are gated.
Table 18. Read Register Settings
Bits
Description
[D7:D2]
[D1:D0]
6-bit binary address for the register to be read
Reserved; set to 00
Rev. 0 | Page 31 of 48
AD7280A
SERIAL INTERFACE
The AD7280A serial interface is Mode 1 SPI compliant, that is,
the clock polarity (CPOL) is 0, and the clock phase (CPHA) is 1.
This device address can then be locked to the AD7280A and used
in subsequent read and write commands. The device address is
written to and read from the AD7280A stack in reverse order,
that is, LSB first.
CS
The interface consists of four signals: , SCLK, SDI, and SDO.
The SDI line is used to transfer data into the on-chip registers,
and the SDO line is used to read the on-chip registers and
conversion result registers. SCLK is the serial clock input for the
device; all data transfers, either on SDI or on SDO, take place
with respect to SCLK. Data is clocked into the AD7280A on the
SCLK falling edge. Data is clocked out of the AD7280A on the
Register Address
The register map for the AD7280A is provided in Table 13. Each
register address is six bits long and is used when writing to or
reading from the on-chip registers of the AD7280A.
Register Data
CS
SCLK rising edge. The
input is used to frame the serial data
being transferred to or from the device.
When issuing a write command to a part in the stack of
AD7280A devices, the data to be written is an 8-bit word. As
shown in Table 13, all read/write registers are eight bits wide.
For more information about the correct settings for each
register, see the Register Map section.
The AD7280A allows 32-bit data transfer only and resets a
CS
counter on the rising edge of
automatically resynchronized with the DSP/microprocessor on
CS
to ensure that the AD7280A is
every falling edge of . Individual 8-bit or 16-bit words can be
Address All Parts
CS
used to assemble a 32-bit command, but a single 32-bit wide
frame is required to correctly structure the assembly of the
32-bit command.
The AD7280A allows write commands to be issued simultane-
ously to all devices in the daisy chain, as well as write commands to
individual AD7280As. A write to all devices in the daisy chain is
completed by setting Bit D12 of the write command to 1. When
issuing a write all command, the device address should be set to
0x00. This device address is also used to calculate the 8-bit CRC
for transmission with the write all command.
CS
The rising edge of
can also be used to initiate the sequence of
conversions by writing to the upper byte of the control register.
Figure 2 shows the timing diagram for the serial interface of the
AD7280A. See the Daisy-Chain Interface section for more
information about the daisy-chain interface.
8-Bit CRC
WRITING TO THE AD7280A
The AD7280A includes an 8-bit cyclic redundancy check (CRC)
on all write commands to either individual devices or to a chain
of devices. An AD7280A that receives an invalid CRC in the
write command does not execute the command. The CRC on
the write command is calculated based on Bits[D31:D11] of the
write command. These bits include the device address, the
register address, the data to be written, the address all parts bit,
and Bit D11. For more information about the CRC, see the
Cyclic Redundancy Check section.
In a battery monitoring application, up to eight AD7280As can
be daisy-chained to allow up to 48 individual Li-Ion cell voltages
to be monitored. Each write operation must, therefore, include
a device address and a register address, in addition to the data
to be written. An additional identifier bit is also required when
addressing all AD7280As in the daisy chain. The AD7280A SPI
interface, in combination with the daisy-chain interface, allows
any register in the stack of eight AD7280As to be updated using
one 32-bit write cycle. The 32-bit write sequence is shown in
Table 20. The AD7280A also requires an 8-bit CRC to be
included in each write command.
Bit Pattern (010)
A required fixed bit pattern of 010 to Bits[D2:D0] of the 32-bit
write command of the AD7280A provides an additional stage of
verification. The correct position of this bit pattern is verified
on each write command received by the AD7280A. An
AD7280A that receives an incorrect bit pattern in the write
command does not execute the command.
Device Address
The device address is a 5-bit address that allows each individual
AD7280A in the battery monitoring stack to be uniquely
identified. On initial power-up, each AD7280A is configured
with a default address of 0x00. A simple sequence of commands
allows each AD7280A to recognize its unique device address in
the stack (see the Initializing the AD7280A section).
Table 20. 32-Bit Write Cycle
Device Address1
Register Address
Register Data
Address All Parts
Reserved (0 Bit)
8-Bit CRC
Bit Pattern (010)
D31 to D27
D26 to D21
D20 to D13
D12
D11
D10 to D3
D2 to D0
1 The device address is configured LSB first. For example, to address the second device in the stack, that is, the first slave device, the sequence of bits input to the
AD7280A should be 10000. The register address, data bits, and CRC bits are input MSB first.
Rev. 0 | Page 32 of 48
AD7280A
Register Address
READING FROM THE AD7280A
The register map for the AD7280A is provided in Table 13. Each
register address is six bits long and is used when writing to or
reading from the on-chip registers of the AD7280A.
There are two types of read operation for the AD7280A:
•
•
Conversion results read
Register data read
Register Data
The data returned from a conversion result read operation includes
the device address, the channel address, the write acknowledge
bit, and the 8-bit CRC information, in addition to the 12 bits of
conversion data. Table 21 illustrates the 32-bit read cycle for a
conversion result read.
The register data is the 8-bit register data that was requested in
a previous write command.
Conversion Data
The conversion data is the 12-bit conversion result from the cell
voltage inputs, the auxiliary ADC inputs, or the ADC self-test
conversion.
The data returned from a register data read operation includes
the device address, the register address, the write acknowledge
bit, and the 8-bit CRC information, in addition to the eight bits
of register data. Table 22 illustrates the 32-bit read cycle for a
register data read.
Write Acknowledge Bit
As described in the Writing to the AD7280A section, an 8-bit
CRC is included in the write command transmitted to the
AD7280A. The CRC is calculated based on Bits[D31:D11]. A
CRC check is completed before the write command is executed
on the device.
The AD7280A SPI interface, in combination with the daisy-
chain interface, allows the conversion results of any AD7280A
in a stack of eight AD7280As to be read back using an N × 8 ×
32-bit read cycle, where N is defined as the number of conver-
sions completed on that part, that is, 12, 9, or 6 (see Table 8).
Using the same CRC algorithm, the AD7280A calculates the
CRC and compares it to the CRC that was received by the part
in the transmitted write command. If the two CRC values
match, the command is executed and the write acknowledge bit
in the subsequent transmission of data from the device is set. If
the transmitted and calculated CRCs do not match, the write
command is not executed, and the write acknowledge bit is set
to 0. For examples of the use of the write acknowledge bit, see
the Write Acknowledge section.
Device Address
The device address is described in the Writing to the AD7280A
section. When reading back register or conversion data from
the device using the daisy-chain readback mode, the SDI line
must be set to write to a specific address. That is, the SDI line
should not be allowed to idle high or low, and the address all
parts bit must be set to 0. The address must be either the top
part in the chain of AD7280A devices or an address with a value
higher than that of the top part in the chain. Writing to the
highest available address (Address 0x1F) and setting the address
all parts bit to 0 is recommended. The 32-bit write command is
0xF800030A.
8-Bit CRC
The AD7280A includes an 8-bit cyclic redundancy check (CRC) on
all data read back from the device. When reading back conversion
data from the AD7280A, the 8-bit CRC includes the device address,
the channel address, the conversion data, and the write acknowl-
edge bit. When reading back register data from the AD7280A,
the 8-bit CRC includes the device address, the register address,
the register data, two reserved zero bits, and the write acknowledge
bit. In both cases, the CRC is generated on Bits[D31:D10] of the
32-bit read cycle and is transmitted using Bits[D9:D2] of the
same read cycle. For more information about the CRC, see the
Cyclic Redundancy Check section.
Channel Address
The channel address allows each individual voltage and auxil-
iary ADC input result to be uniquely identified. Each channel
address is four bits wide. The address for each channel is provided
in the register map (see Table 13).
Table 21. 32-Bit Read Conversion Result Cycle
Device Address1
Channel Address
Conversion Data
Write Acknowledge
8-Bit CRC
Reserved (0 Bits)
D31 to D27
D26 to D23
D22 to D11
D10
D± to D2
D1 to D0
1 The device address is configured LSB first. For example, to address the second device in the stack, that is, the first slave device, the sequence of bits input to the
AD7280A should be 10000. The register address, channel address, data bits, and CRC bits are input MSB first.
Table 22. 32-Bit Read Register Data Cycle
Device Address1
Register Address
Register Data
Reserved (0 Bits) Write Acknowledge 8-Bit CRC
D12 to D11 D10 D± to D2
Reserved (0 Bits)
D31 to D27
D26 to D21
D20 to D13
D1 to D0
1 The device address is configured LSB first. For example, to address the second device in the stack, that is, the first slave device, the sequence of bits input to the
AD7280A should be 10000. The register address, data bits, and CRC bits are input MSB first.
Rev. 0 | Page 33 of 48
AD7280A
DAISY-CHAIN INTERFACE
In a battery monitoring application, up to eight AD7280As can
be daisy-chained together to allow up to 48 individual lithium
ion cell voltages to be monitored. Each AD7280A is capable of
monitoring up to six Li-Ion cells and is powered from the top
and bottom voltage of the six Li-Ion cells. As a result, the supply
voltages of each AD7280A are offset by up to 30 V from
adjacent AD7280As in the chain. For this reason, a standard
serial interface daisy-chain method cannot be used.
ADDRESSING THE AD7280A WHILE READING
BACK CONVERSION OR REGISTER DATA
An SPI interface reads data and writes data at the same time: as
the device is reading in one command, it provides output data
on the SDO pin in the same read/write cycle. When reading both
register and conversion data from the AD7280A using the daisy-
chain readback mode, the SDI line must not idle high or low; it
must be set up to address and write to either the top device used
in the daisy chain or to a device with an address higher than the
top device used in the daisy chain. In either case, the address all
parts bit (Bit D12 in the write command) should be set to 0, and
a valid CRC must be included. Writing to the highest available
address, that is, Address 0x1F, and setting the address all parts
bit to 0 is recommended. The 32-bit write command is
0xF800030A.
The AD7280A includes a daisy-chain interface separate from
the standard SPI interface. This daisy-chain interface allows
each AD7280A in the chain to relay data to and from adjacent
AD7280As.
As described in the Serial Interface section, the SPI interface
CS
consists of four signals: , SCLK, SDI, and SDO. In addition
to these pins, there are three optional interface pins: ALERT,
CNVST
PD
, and
. Each of these seven interface signals is
INITIALIZING THE AD7280A
mirrored in the daisy-chain interface to allow communication
between adjacent devices in a daisy chain. For example, the
serial clock of each AD7280A is received on the SCLK pin and
passed to the device above it in the daisy chain using the
SCLKhi pin.
On initial power-up and when coming out of power-down, all
AD7280As default to a device address of 0x00. The following
sequence of commands should be followed to allow each AD7280A
in the daisy chain to recognize its unique position in the chain.
The following sequence allows device addresses on all parts in
the chain to be configured and confirmed through daisy-chain
readback. A subset of these commands can also be used to
configure the device addresses without readback confirmation.
CS
The , SCLK, SDI,
CNVST
PD
, and pins, which pass data up
the daisy chain, operate as 3 V or 5 V logic interface pins when
the AD7280A is configured as a master device; these pins
operate as daisy-chain interface pins when the AD7280A is
configured as a slave device.
1. A single command should be sent to all devices in the
chain to assert the lock device address bit (D2), to deassert
the increment device address bit (D1), and to assert the
daisy-chain register readback bit (D0). The 32-bit write
command is 0x01C2B6E2.
2. A second command should be sent to all devices in the
chain to write the address of the lower byte of the control
register, 0x0E, to the read register on all devices. The 32-bit
write command is 0x038716CA.
The SDO and ALERT pins operate as 3 V or 5 V logic interface
pins when the AD7280A is configured as a master device. These
pins are tristated when the AD7280A is configured as a slave
device. Two additional pins, SDOlo and ALERTlo, are required
to pass data down the daisy chain.
As described in the Serial Interface section, only one 32-bit
write cycle is required to write to any register in a stack of eight
AD7280As. The readback of conversion data from all channels
monitoring the battery stack requires an N × 8 × 32-bit read cycle,
where N is defined as the number of conversions completed on
that part, that is, 12, 9, or 6. The recommended SCLK frequency
to ensure correct operation of the daisy-chain interface is 1 MHz.
With a 1 MHz SCLK, it takes approximately 1.54 ms to read
back the voltage conversions on 48 channels.
3. To verify that all AD7280As in the chain have received and
locked their unique device address, a daisy-chain register read
should be requested from all devices. This can be done by
CS
continuing to apply sets of 32 SCLKs framed by
until
the lower byte of the control register of each device in the
daisy chain has been read back. The user should confirm
that all device addresses are in sequence. The 32-bit write
command is 0xF800030A.
When reading from a single device in a stack of AD7280A devices
(daisy-chain register readback is disabled; Bit D0 of the control
register = 0), the SCLK frequency must be lower than 1 MHz to
read back the register data from parts up the chain of AD7280As.
This is due to the propagation delay between adjacent parts in
the daisy chain (see tDELAY in Table 3). This delay does not apply
if the part is reading registers or conversion data from the part
in daisy-chain mode; that is, the maximum SCLK of 1 MHz can
always be used in daisy-chain mode.
4. This command should be repeated until the control
register data has been read back from all devices in the
daisy chain.
Rev. 0 | Page 34 of 48
AD7280A
For example, to read back the write acknowledge bit from
WRITE ACKNOWLEDGE
Device 1 in the chain after writing to a register on that device,
the read operation of Device 0, the master device, must be turned
off. Also, the SCLK frequency must be lower than 1 MHz when
reading back the write acknowledge bit from devices higher in
the chain than the master device in this mode.
For all write commands received by the AD7280A, the device
internally performs a CRC calculation on Bits[D31:D11] of the
received data and verifies this CRC against the CRC transmitted
by the DSP/microprocessor. If there is a difference between the
CRC generated internally and the CRC received from the DSP/
microprocessor, the AD7280A does not perform the write oper-
ation. The AD7280A also checks for the correct position of the
bit pattern 010 in the write command, as described in the Serial
Interface section. If there is a difference between the expected
010 pattern and the pattern received from the DSP/microprocessor,
the AD7280A does not perform the write operation.
CYCLIC REDUNDANCY CHECK
The AD7280A 32-bit SPI interface includes an 8-bit cyclic
redundancy check (CRC) on the read and write cycles. The CRC
can be used to detect alterations in the data during transmission
to and from the AD7280A. The principle of a cyclic redundancy
check is that the data to be transmitted is divided by a fixed poly-
nomial. The remainder of this mathematical operation is then
attached to the data and forms part of the transmission. At the
receiving end, the same mathematical operation should be com-
pleted on the data received. This operation confirms that the
data received is the same as the data that was originally transmitted.
CS
If a subsequent 32 SCLK cycle framed by a
pulse is applied
to the AD7280A, Bit D10 (the write acknowledge bit) on SDO
indicates to the processor whether the last write to the device
was successful (the write acknowledge bit is set if the write was
successful). The write acknowledge bit is included in the 8-bit
CRC on the read cycle. Note that the read register must be loaded
with any value other than 0x00 for the write acknowledge bit to
be correctly passed down the chain of AD7280A devices.
The polynomial used by the AD7280A to calculate the CRC bits
is x8 + x5 + x3 + x2 + x + 1. This CRC polynomial has a Hamming
distance of 4 for calculations up to 22 bits of data. The division
is implemented using the digital circuit shown in Figure 40.
Following is an example of how the write acknowledge bit can
be used when writing to and configuring a stack of AD7280A
devices. This example sets the high byte of the control register
settings on all devices in a stack of eight AD7280As.
Write Operation CRC
For writes to the AD7280A, the CRC must be computed in the
DSP/microprocessor and sent as part of the write command.
The CRC must be computed on Bits[D31:D11] of the write
command, that is, the device address, the register address, the
data to be written, the address all parts bit, and Bit D11, which
is a reserved zero input bit. The data is divided by the CRC
polynomial, and the 8-bit remainder, following the division,
becomes the CRC bits, CRC_7 to CRC_0.
1. Execute a write all command to load the read register with
0x0E (addresses the low byte of the control register).
2. Execute a write all command to set the high byte of the
control register (Address 0x0D) to the desired values.
3. Apply an additional eight sets of 32 SCLKs, each framed by
CS
, to the master device. The device address bits, D31 to
D27, should be set to 0x1F for each 32 SCLK frame. The
32-bit write command is 0xF800030A. The data read back
from the master device on the first 32 SCLK frame includes
the write acknowledge bit for the control register high byte
write to the master device. The data read back on the
second 32 SCLK frame includes the write acknowledge bit
for the control register high byte write to the first slave
device in the stack, and so on.
If the user is addressing all parts in a stack of AD7280As (by
asserting the address all parts bit, D12), the CRC must be com-
puted using a device address of 0x00, and the data written to the
device must have a device address of 0x00. The AD7280A performs
the same CRC calculation on Bits[D31:D11] of the received data,
and it verifies this CRC against the CRC transmitted by the DSP/
microprocessor. If there is a difference between the CRC gener-
ated within the AD7280A and the CRC received from the DSP/
microprocessor, the AD7280A does not perform the write opera-
tion. To allow the user to verify that the command has been
received and implemented by the AD7280As in the stack, a
write acknowledge bit is also included in the 32-bit read cycles.
For more information about the write acknowledge bit, see the
Write Acknowledge section.
To read back the write acknowledge bit from slave AD7280As
in a daisy chain when single registers are being written to,
Bits[D13:D12] of the control register on lower devices in the
chain must be set to 1 (a no-read operation on those devices).
DATA_IN
SCLK
D
Q
D
Q
D
Q
D
Q
D
Q
D
Q
D
Q
D
Q
CRC_0
CRC_1
CRC_2
CRC_3
CRC_4
CRC_5
CRC_6
CRC_7
Figure 40. CRC Implementation
Rev. 0 | Page 35 of 48
AD7280A
Read Operation CRC
CRC Calculation Example 1
For reads from the AD7280A, the 8-bit CRC is generated by the
AD7280A based on Bits[D31:D10] of the 32-bit read cycle and is
transmitted using Bits[D9:D2] of the same read cycle. The data
received is divided by the CRC polynomial, and the 8-bit remain-
der, following the division, becomes the CRC bits, CRC_7 to
CRC_0. The user can compare the CRC bits calculated with the
CRC that was received from the AD7280A to verify that there was
no alteration in the data that was transmitted by the AD7280A.
This example shows how a 32-bit write command, including the
CRC calculation, to the high byte of the control register on the
master device (Device 0) is assembled. The data to be written
is 0x0C.
The CRC is computed in the DSP/microprocessor on
Bits[D31:D11], that is, the device address, the register address,
the data to be written to the register, the address all parts bit,
and the reserved bit.
When operating in a daisy chain, each AD7280A receives conver-
sion or register data from the device above it in the daisy chain
and performs a CRC calculation on the received data. If there is
a difference between the CRC generated internally and the CRC
received from the device above it in the daisy chain, the AD7280A
replaces the received CRC by an inversion of the internally gen-
erated CRC.
•
•
•
•
•
Device address: 00000 (0x00)
Register address: 001101 (0x0D)
Data: 00001100 (0x0C)
Address all parts bit: 0 (0x0)
Reserved bit: 0 (0x0)
The data input to the CRC algorithm is, therefore,
000000011010000110000 (0x003430).
CRC Pseudocode
Following the completion of the calculation, the value
of CRC_7 to CRC_0 is 01010001 (0x51). The data that
is sent to the AD7280A for this serial write is, therefore,
0000 0001 1010 0001 1000 0010 1000 1010 (0x01A1828A).
The following pseudocode can be used to calculate the CRC.
The following variables must first be declared:
•
Num_Bits is the number of data bits used to calculate the
CRC result: 21 for a data write to the AD7280A, and 22 for
a data read from the AD7280A.
CRC Calculation Example 2
•
•
i is an integer variable.
This example shows how a 32-bit write command, including
the CRC calculation, to the high byte of the control register on
Device 1 in the daisy chain is assembled. The data to be written
is 0x0C.
xor_1, xor_2, xor_3, xor_4, and xor_5 are integer variables.
These outputs of the XOR gates start with the leftmost
XOR gate in the circuit implementation (see Figure 40).
data_in represents the data bits that the CRC is calculated
on: Bits[D31:D11] for a write operation, and Bits[D31:D10]
for a read operation. This data supplies the input to the
first XOR gate.
CRC_0, CRC_1, CRC_2, CRC_3, CRC_4, CRC_5, CRC_6,
and CRC_7 are integer variables. The outputs of the shift
registers start at the leftmost shift register in the circuit
implementation (see Figure 40).
•
•
The CRC is computed in the DSP/microprocessor on
Bits[D31:D11], that is, the device address, the register address,
the data to be written to the register, the address all parts bit,
and the reserved bit.
•
•
•
•
•
Device address (written LSB first): 10000 (0x10)
Register address: 001101 (0x0D)
Data: 00001100 (0x0C)
Address all parts bit: 0 (0x0)
Reserved bit: 0 (0x0)
With the exception of data_in, all variables should be initialized
to 0. The following code implements the CRC calculation as
shown in Figure 40.
The data input to the CRC algorithm is, therefore,
100000011010000110000 (0x103430).
for (i=Num_Bits; i>=0; i--)
{
Following the completion of the calculation, the value of
CRC_7 to CRC_0 is 01110100 (0x74). The data that is sent
to the AD7280A for this serial write is, therefore,
xor_5 = CRC_4 ^ CRC_7;
xor_4 = CRC_2 ^ CRC_7;
xor_3 = CRC_1 ^ CRC_7;
xor_2 = CRC_0 ^ CRC_7;
xor_1 = data_in[i] ^ CRC_7;
1000 0001 1010 0001 1000 0011 1010 0010 (0x81A183A2).
CRC_7 = CRC_6;
CRC_6 = CRC_5;
CRC_5 = xor_5;
CRC_4 = CRC_3;
CRC_3 = xor_4;
CRC_2 = xor_3;
CRC_1 = xor_2;
CRC_0 = xor_1;
}
Rev. 0 | Page 36 of 48
AD7280A
CRC Calculation Example 3
CRC Calculation Example 4
This example shows the breakdown of a 32-bit register read
from the low byte of the control register of the master device,
that is, Device 0.
This example shows the breakdown of a 32-bit conversion result
read from the Cell Voltage 3 conversion result register of Device 1.
The CRC is computed in the AD7280A on Bits[D31:D10], that
is, the device address, the channel address, the conversion data,
and the write acknowledge bit. The calculated CRC is sent along
with Bits[D31:D10] and Bits[D1:D0] to the DSP/microprocessor.
The CRC is computed in the AD7280A on Bits[D31:D10], that
is, the device address, the register address, the register data, two
reserved zero bits, and the write acknowledge bit. The
calculated CRC is sent along with Bits[D31:D10] and
Bits[D1:D0] to the DSP/microprocessor.
The data received from the AD7280A is as follows:
1000 0001 0100 1100 1101 0101 0001 1000 (0x814CD518).
The data received from the AD7280A is as follows:
0000 0001 1100 0010 1000 0110 0110 1000 (0x01C28668).
•
•
•
•
•
•
Device address (read LSB first): 10000 (0x10)
Channel address: 0010 (0x2)
Conversion data: 100110011010 (0x99A)
Write acknowledge: 1 (0x1)
CRC: 01000110 (0x46)
Reserved 0s: 0 (0x0)
•
•
•
•
•
•
•
Device address: 00000 (0x00)
Register address: 001110 (0x0E)
Register data: 00010100 (0x14)
Reserved 0s: 0 (0x0)
Write acknowledge: 1 (0x1)
CRC: 10011010 (0x9A)
The CRC bits are computed again in the DSP/microprocessor
on Bits[D31:D10] of the data that is read back from the
AD7280A. The data input to the CRC algorithm is, therefore,
1000000101001100110101 (0x205335).
Reserved 0s: 0 (0x0)
The CRC bits are computed again in the DSP/microprocessor
on Bits[D31:D10] of the data that is read back from the AD7280A.
The data input to the CRC algorithm is, therefore,
0000000111000010100001 (0x0070A1).
Following the completion of the calculation, the value of
CRC_7 to CRC_0 is 01000110 (0x46). This result matches
the CRC that was sent from the AD7280A; therefore, this
transmission of data is valid.
Following the completion of the calculation, the value of
CRC_7 to CRC_0 is 10011010 (0x9A). This result matches
the CRC that was sent from the AD7280A; therefore, this
transmission of data is valid.
Rev. 0 | Page 37 of 48
AD7280A
EXAMPLES OF INTERFACING WITH THE AD7280A
The AD7280A supports a number of read options. The user can
read back the results from
CONVERT AND READBACK ROUTINE
When conversion data from any or all of the AD7280As in a
daisy chain is read back, the conversion results returned from
the AD7280A are the last completed set of conversions on that
part. It is recommended that the user also set Bits[D15:D14] of
the control register to select the number of conversions to be
completed on each part and initiate the conversions through
•
•
•
All conversions completed on all parts in the chain
Individual registers on all parts in the chain
Individual registers on selected parts in the chain
In each case, the user must first write to the read register on the
selected parts to configure that part to supply the correct data
on the outputs. When reading back an individual register, the
address of that register should be written to the read register of
the selected part. When reading back conversion results from
any or all parts in the chain, an address of 0x00 should be written
to the read register of the selected parts.
CNVST
CS
either the
pin or the rising edge of
as part of the
read operation. In this way, the user can implement a simple
convert and readback routine with the most efficient number
of 32-bit write and read operations.
A general example of this routine, which converts and reads
back from all parts in the AD7280A daisy chain, is as follows:
When the address written to the read register is 0x00, the
conversion results selected for readback are controlled by
setting Bits[D13:D12] of the control register (see Table 14).
These bits allow the user to select one of four different read-
back options:
1. Write 0x00 to the read register on all parts in the daisy
chain. Note that 0x00 is the default value of this register
on power-up and following a software reset operation.
2. Write to the control register on all parts. Set Bits[D15:D14]
to select the required conversions. Set Bits[D13:D12] to
select the required conversion results for readback.
•
Read back 12 conversion results: six voltage and six
auxiliary.
3. Initiate the conversions through either the falling edge of
•
Read back nine conversion results: six voltage and three
auxiliary.
CNVST
CS
or the rising edge of
(set Bit D11 of the control
register to select the conversion start format).
4. Allow sufficient time for each conversion to be completed
plus tWAIT. See the Converting Cell Voltages and Auxiliary
ADC Inputs section.
•
•
Read back six conversion results: six voltage results only.
Switch off the read operation on this part.
To read back an individual register from a single AD7280A in
the daisy chain, follow these steps:
CS
5. Apply a
low pulse that frames 32 SCLKs for each
conversion result to be read back.
1. On all other parts in the chain, set Bits[D13:D12] of the
control register to 11 to select the no-read operation on
those parts.
2. On the targeted part, set Bits[D13:D12] of the control
register to turn on the read operation.
EXAMPLES
The following examples of conversion and/or readback routines
can be used in an application that implements a chain of AD7280A
devices to monitor the voltage and/or auxiliary ADC inputs of
the AD7280A on a stack of lithium ion batteries.
Note that it is more efficient in terms of 32-bit write cycles to
first switch off the read operation on all AD7280As in the daisy
chain. This is achieved with a single write cycle, using Bit D12
in the write command to address all parts in the chain. The user
can then address the individual part and set Bits[D13:D12] of
the control register to turn on the read operation for that part.
Rev. 0 | Page 38 of 48
AD7280A
Example 1: Initialize All Parts in a Daisy Chain on Initial
Power-Up and When Coming Out of Power-Down
Example 2: Convert and Read All Parts, All Voltages,
and All Auxiliary ADC Inputs
Example 1 shows a typical device initialization routine.
In this example, it is assumed that all AD7280As in the daisy
chain have been initialized to their correct device addresses.
1. To initialize all device addresses, set Bit D2 and Bit D0
of the control register to 1, and set Bit D1 of the control
register to 0 on all parts in the chain. The 32-bit write
command is 0x01C2B6E2 (see Table 23, Write 1).
2. Write the register address corresponding to the lower byte
of the control register to the read register on all parts. The
32-bit write command is 0x038716CA (see Table 23, Write 2).
1. Write Register Address 0x00 to the read register on all
parts. A device address of 0x00 is used when computing
the CRC for commands to write to all parts. The 32-bit
write command is 0x38011CA (see Table 24, Write 1).
Note that 0x00 is the default value of the read register on
power-up and after a software reset; therefore, this write
operation may not be necessary.
CS
3. Apply a
low pulse that frames 32 SCLKs for each device
in the chain to be read back. All conversion readbacks
should simultaneously write the 32-bit command
0xF800030A, as described in the Serial Interface section
(see Table 23, Write 3). This read is used to verify that all
AD7280As in the chain have received and locked their
unique device addresses. Confirm that all device addresses
are in sequence.
2. Set Bits[D15:D12] of the control register to 0 on all parts.
The 32-bit write command is 0x01A0131A (see Table 24,
Write 2).
Note that this is the default value of Bits[D15:D12] of the
control register on power-up and after a software reset;
therefore, this write operation may not be necessary.
CNVST
3. Program the
control register to 0x02 on all parts
CNVST
to allow conversions to be initiated using the
pin.
The 32-bit write command is 0x03A0546A (see Table 24,
Write 3).
CNVST
4. Initiate conversions through the falling edge of
.
5. Allow sufficient time for all conversions to be completed
plus tWAIT. Following the completion of all conversions,
CS
apply a
low pulse that frames 32 SCLKs for each conver-
sion result to be read back. The 32-bit write command is
0xF800030A, as described in the Serial Interface section
(see Table 24, Write 4).
Table 23. Example 1: Initializing All AD7280A Devices in a Daisy Chain
32-Bit Write
Write Command
Write 1
Write 2
Device Address
00000
00000
Register Address Data
Write All
D11
8-Bit CRC
11011100
11011001
01100001
D2 to D0 Command
001110
011100
000000
00010101
00111000
00000000
1
1
0
0
0
0
010
010
010
0x01C2B6E2
0x038716CA
0xF800030A
Write 3
11111
Table 24. Example 2: Converting and Reading All Voltages and All Auxiliary ADC Inputs from All AD7280A Devices
32-Bit Write
D2 to D0 Command
Write Command
Write 1
Write 2
Write 3
Write 4
Device Address
00000
00000
00000
11111
Register Address Data
Write All
D11
8-Bit CRC
00111001
01100011
10000101
01100001
011100
001101
011101
000000
00000000
1
1
1
0
0
0
0
0
010
010
010
010
0x038011CA
0x01A0131A
0x03A0546A
0xF800030A
00000000
00000010
00000000
Rev. 0 | Page 3± of 48
AD7280A
Example 3: Convert and Read All Parts, All Voltages,
and Three Auxiliary ADC Inputs per Part
CNVST
3. Program the
control register to 0x02 on all parts
CNVST
to allow conversions to be initiated using the
pin.
The 32-bit write command is 0x03A0546A (see Table 25,
Write 3).
In this example, it is assumed that all AD7280As in the daisy
chain have been initialized to their correct device addresses.
CNVST
4. Initiate conversions through the falling edge of
.
1. Write Register Address 0x00 to the read register on all
parts. A device address of 0x00 is used when computing
the CRC for commands to write to all parts. The 32-bit
write command is 0x038011CA (see Table 25, Write 1).
5. Allow sufficient time for all conversions to be completed
plus tWAIT. Following the completion of all conversions,
CS
apply a
low pulse that frames 32 SCLKs for each conver-
sion result to be read back. The 32-bit write command is
0xF800030A, as described in the Serial Interface section
(see Table 25, Write 4).
Note that 0x00 is the default value of the read register on
power-up and after a software reset; therefore, this write
operation may not be necessary.
2. Set Bit D15 and Bit D13 of the control register to 0 on all
parts. Set Bit D14 and Bit D12 of the control register to 1
on all parts. The 32-bit write command is 0x01AA1062
(see Table 25, Write 2).
Table 25. Example 3: Converting and Reading All Voltages and Three Auxiliary ADC Inputs from All AD7280A Devices
32-Bit Write
D2 to D0 Command
Write Command
Write 1
Write 2
Write 3
Write 4
Device Address
00000
00000
00000
11111
Register Address Data
Write All
D11
8-Bit CRC
00111001
00001100
10000101
01100001
011100
001101
011101
000000
00000000
1
1
1
0
0
0
0
0
010
010
010
010
0x038011CA
0x01AA1062
0x03A0546A
0xF800030A
01010000
00000010
00000000
Rev. 0 | Page 40 of 48
AD7280A
Example 4: Convert and Read a Single Voltage
or Auxiliary ADC Input Result from One Part
CNVST
control register to 0x02 on Device 3
4. Program the
CNVST
to allow conversions to be initiated using the
pin
on that part. The 32-bit write command is 0xC3A0417A
(see Table 26, Write 4).
In this example, it is assumed that all AD7280As in the daisy
chain have been initialized to their correct device addresses.
CNVST
5. Initiate conversions through the falling edge of
6. Allow sufficient time for all conversions to be completed
plus tWAIT
7. Program the
.
1. The register address corresponding to the voltage or
auxiliary ADC input result to be read should be written to
the read register of the part to be read (see Table 13 for
register addresses). In this example, the Cell Voltage 6
register result is read from Device 3 in the stack. The 32-bit
write command is 0xC382865A (see Table 26, Write 1).
2. Set Bits[D13:D12] of the control register to 1 on all parts.
This setting turns off the read operation on all parts. The
32-bit write command is 0x01B617EA (see Table 26,
Write 2).
.
control register to gate the
CNVST
CNVST
signal on all parts. The 32-bit write command is
0x03A0340A (see Table 26, Write 5). This write prevents
unintentional conversions from being initiated by noise or
glitches on the
pin. This write also updates the on-
CNVST
chip output registers of all devices in the daisy chain.
CS
8. Apply a
low pulse that frames 32 SCLKs to read back
3. Set Bits[D13:D12] of the control register of the part to be
read from such that the required voltage is read back. With
the exception of a self-test conversion, it is not possible to
convert on a single channel; six, nine, or 12 conversions must
be completed. This example reads a voltage conversion from
Device 3 in the stack; therefore, Bit D14 and Bit D12 of the
control register should be set to 0, and Bit D15 and Bit D13
should be set to 1 on Device 3. The 32-bit write command
is 0xC1B400FA (see Table 26, Write 3).
the desired voltage or auxiliary ADC result. This frame
should simultaneously write the 32-bit command
0xF800030A, as described in the Serial Interface section
(see Table 26, Write 6).
Note that when reading from a single device in a stack of
AD7280As, the SCLK frequency must be lower than 1 MHz
to read back the register data from parts higher in the chain
than the master device.
Table 26. Example 4: Converting and Reading a Single Voltage or Auxiliary ADC Result from One AD7280A Device
32-Bit Write
D2 to D0 Command
Write Command
Write 1
Write 2
Write 3
Write 4
Device Address
11000
00000
11000
11000
Register Address Data
Write All
D11
0
0
0
0
8-Bit CRC
11001011
11111101
00011111
10000111
10000001
01100001
011100
001101
001101
011101
011101
000000
00010100
0
1
0
0
1
0
010
010
010
010
010
010
0xC382865A
0x01B617EA
0xC1B400FA
0xC3A0417A
0x03A0340A
0xF800030A
10110000
10100000
00000010
00000001
00000000
Write 5
Write 6
00000
11111
0
0
Rev. 0 | Page 41 of 48
AD7280A
Example 5: Read a Single Configuration Register
on All Parts
Example 6: Read a Single Configuration Register
from One Part
In this example, it is assumed that all AD7280As in the daisy
chain have been initialized to their correct device addresses.
In this example, it is assumed that all AD7280As in the daisy
chain have been initialized to their correct device addresses.
1. Set Bit D0 of the control register to 1 on all parts. This write
enables the daisy-chain register read operation on all parts.
The 32-bit write command is 0x01C2B6E2 (see Table 27,
Write 1).
2. The register address corresponding to the configuration
register to be read should be written to the read register on
all parts (see Table 13 for register addresses). In this example,
the cell balance register is read from all parts. The 32-bit
write command is 0x038A12B2 (see Table 27, Write 2).
1. Set Bits[D13:D12] of the control register to 1 on all parts.
This setting turns off the read operation on all parts. The
32-bit write command is 0x01A6151A (see Table 28, Write 1).
2. Set Bits[D13:D12] of the control register of the part to be
read from to 0. In this example, Device 1 in the stack is to
be read from. The 32-bit write command is 0x81A00222
(see Table 28, Write 2).
3. The register address corresponding to the configuration
register to be read should be written to the read register of
the part that is to be read (see Table 13 for register
addresses). This example reads the alert register from
Device 1 in the stack. The 32-bit write command is
0x8389800A (see Table 28, Write 3).
CS
3. Apply a
low pulse that frames 32 SCLKs for each device
in the stack to read back the desired register contents from
all parts. This frame should simultaneously write the 32-bit
command 0xF800030A, as described in the Serial Interface
section (see Table 27, Write 3).
CS
4. Apply a
low pulse that frames 32 SCLKs to read back
the desired register contents. This frame should simultan-
eously write the 32-bit command 0xF800030A, as
described in the Serial Interface section (see Table 28,
Write 4). When reading from a single device in a stack of
AD7280As, the SCLK frequency must be lower than
1 MHz to read back the register data from parts higher in
the chain than the master device.
Table 27. Example 5: Reading a Single Configuration Register from All AD7280A Devices
32-Bit Write
D2 to D0 Command
Write Command
Write 1
Write 2
Device Address
00000
00000
Register Address Data
Write All
D11
8-Bit CRC
11011100
01010110
01100001
001110
011100
000000
00010101
01010000
00000000
1
1
0
0
0
0
010
010
010
0x01C2B6E2
0x038A12B2
0xF800030A
Write 3
11111
Table 28. Example 6: Reading a Single Configuration Register from One AD7280A Device
32-Bit Write
D2 to D0 Command
Write Command
Write 1
Write 2
Write 3
Write 4
Device Address
00000
10000
10000
11111
Register Address Data
Write All
D11
8-Bit CRC
10100011
01000100
00000001
01100001
001101
001101
011100
000000
00110000
1
0
0
0
0
0
0
0
010
010
010
010
0x01A6151A
0x81A00222
0x838±800A
0xF800030A
00000000
01001100
00000000
Rev. 0 | Page 42 of 48
AD7280A
Example 7: Self-Test Conversion on All Parts
CNVST
7. The
control register should be programmed to
CNVST
command is 0x03A0340A (see Table 29, Write 5). This
write prevents unintentional conversions from being
gate the
signal on all parts. The 32-bit write
Example 7 shows a self-test conversion routine for all parts in a
daisy chain.
1. To select the self-test conversion, set Bits[D15:D14] of the
control register to 1, and set Bits[D13:D12] of the control
register to 0 on all parts. The 32-bit write command is
0x01B81092 (see Table 29, Write 1).
2. Set Bit D0 of the control register to 1 on all parts. This
setting enables the daisy-chain register read operation on
all parts. The 32-bit write command is 0x01C2B6E2 (see
Table 29, Write 2).
CNVST
initiated by noise or glitches on the
pin. This write
also updates the on-chip output registers of all devices in
the daisy chain.
CS
8. Apply a
low pulse that frames 32 SCLKs to read back
the desired voltage. This frame should simultaneously
write the 32-bit command 0xF800030A, as described in
the Serial Interface section (see Table 29, Write 6).
3. The register address corresponding to the self-test
conversion should be written to the read register of all
parts (see Table 13 for register addresses). The 32-bit write
command is 0x038617CA (see Table 29, Write 3).
Example 8: Software Reset on All Parts
Example 8 shows a software reset routine for all parts in a
daisy chain.
1. Set Bit D7 of the control register to 1 on all parts to place
the AD7280A into software reset. The 32-bit write command
is 0x01D2B412 (see Table 30, Write 1).
2. Set Bit D7 of the control register to 0 on all parts to take the
AD7280A out of software reset. The 32-bit write command
is 0x01C2B6E2 (see Table 30, Write 2).
CNVST
4. Program the
control register to 0x02 on all parts
CNVST
to allow conversions to be initiated using the
pin.
The 32-bit write command is 0x03A0546A (see Table 29,
Write 4).
CNVST
5. Initiate conversions through the falling edge of
6. Allow sufficient time for the self-test conversions to be
completed plus tWAIT
.
.
Table 29. Example 7: Self-Test Conversion on All AD7280A Devices
32-Bit Write
D2 to D0 Command
Write Command
Write 1
Write 2
Write 3
Write 4
Device Address
00000
00000
00000
00000
Register Address Data
Write All
D11
0
0
0
0
8-Bit CRC
00010010
11011100
11111001
10000101
10000001
01100001
001101
001110
011100
011101
011101
000000
11000000
1
1
1
1
1
0
010
010
010
010
010
010
0x01B810±2
0x01C2B6E2
0x038617CA
0x03A0546A
0x03A0340A
0xF800030A
00010101
00110000
00000010
00000001
00000000
Write 5
Write 6
00000
11111
0
0
Table 30. Example 8: Software Reset for All AD7280A Devices
32-Bit Write
D2 to D0 Command
Write Command
Write 1
Write 2
Device Address
00000
00000
Register Address Data
Write All
D11
0
0
8-Bit CRC
10000010
11011100
001110
001110
10010101
00010101
1
1
010
010
0x01D2B412
0x01C2B6E2
Rev. 0 | Page 43 of 48
AD7280A
EMC GUIDELINES
Note that these ferrite beads can be replaced with a small value
of resistance. The maximum value of resistance that can be
used is 20 Ω. A resistor should not be included on the VSS
line to the master chip. Instead, a direct connection should
be made from the battery cell connector to the VSS pin.
SCHEMATIC AND LAYOUT GUIDELINES
To optimize the performance of a chain of AD7280A devices
under noisy conditions—for example, when experiencing
electromagnetic interference—the following schematic and
layout guidelines should be observed (see Figure 29).
Analog Devices, Inc., also recommends the following:
1. All AD7280A devices in a daisy chain should be physically
located on a single printed circuit board (PCB). Daisy-
chain connections between PCBs are not recommended.
Individual PCBs can be used for separate daisy chains. In
this case, however, communication between PCBs is via a
communication protocol such as SPI or CAN.
•
Inclusion of a 100 nF capacitor across the six individual cells
that are monitored by the AD7280A. This capacitor should
be placed physically close to the battery cell connector on
the PCB.
•
Correct termination of all unused pins on the device. More
information about the correct termination of unused pins
can be found in the Pin Configuration and Function
Descriptions section.
2. Individual 22 pF capacitors should be placed on each
daisy-chain connection. The capacitors should be
terminated to either the VSS pin of the upper device or the
VDD pin of the lower device, depending on the direction in
OPERATION IN A NOISY ENVIRONMENT
PD CS
which data is flowing in the daisy chain. The
CNVST
,
,
When the AD7280A is operating in a noisy environment—for
example, when electromagnetic interference is experienced—
glitches can occur on the SPI or daisy-chain inputs and outputs.
To limit the effect that such glitches may have on the operation
of the AD7280A, each daisy-chain input is passed through a
filter before being applied internally within the device. The filter
SCLK, SDI, and
daisy-chain connections pass data
up the chain. The 22 pF capacitors on these pins should be
terminated to the VSS pin of the upper device in the chain.
The SDOlo and ALERTlo daisy-chain connections pass
data down the chain. The 22 pF capacitors on these pins
should be terminated to the VDD pin of the lower device in
the chain.
PD
on the
more information). The filter on the remaining daisy-chain
CS CNVST
pin is 130 μs wide (see the Power-Down section for
3. A direct, low impedance trace should connect the VDD pin
of the lower device with the VSS pin of the upper device. The
AD7280A daisy-chain connections operate at the VDD/VSS
voltage of the adjacent AD7280As. Ensuring a low imped-
ance path between the supplies optimizes the performance
of the daisy-chain communications.
4. The application PCB should have a minimum of four
layers. The AD7280A daisy-chain connections should be
routed on an inner layer of the PCB.
inputs ( , SCLK, SDI,
, SDIhi, and ALERThi) is 150 ns
wide. Glitches wider than these values on any of the pins can
have an effect on the AD7280A, and care should be taken to
ensure correct operation.
CS
Glitches that occur on the SCLK and
pins can result in the
AD7280A losing synchronization with the DSP/microprocessor.
However, such a loss of synchronization affects only the 32-bit
word during which the glitch occurred. The AD7280A interface
5. The AD7280A daisy-chain connections should be shielded
above and below by a VSS supply plane connected to the VSS
pin of the upper device in the chain. The shield should extend
from the VSS and daisy-chain low pins of the upper device
(Pin 15, Pin 17, and Pin 21 to Pin 28) to cover the daisy-
chain high pins of the lower device (Pin 42 to Pin 48), as
well as a low impedance trace to the VDD pin. This shield
provides maximum protection to the daisy-chain connec-
tions when operating in a noisy environment.
CS
is reset on the rising edge of
to ensure that the part is resyn-
chronized, as described in the Serial Interface section.
Glitches that occur on the SDI or SDOhi pin can result in a
change of state of any of the bits in the 32-bit words that are
written to or read from the chain of AD7280As. In this event,
the 8-bit CRC received by the AD7280A or by the DSP/micro-
processor should not match the CRC that is calculated based
on the 32-bit word that was transmitted.
6. The AD7280A devices should be placed as close together
as possible on the PCB to minimize the length of the daisy-
chain connections.
7. To minimize noise reaching the VDD/VSS pins of the
AD7280A, ferrite beads should be inserted into the VDD
and VSS supply traces coming from the battery. These beads
can be inserted into the PCB traces between the battery cell
connection on the PCB and the individual supply pins.
Glitches that occur on the ALERThi pin are observed on the
alert signal when output from the master device. Care should
be taken when designing the alert response software or hard-
ware to ensure that such glitches are treated appropriately in
the system.
CNVST
Glitches that occur on the
pin may be interpreted as a
conversion start request. If this occurs during a read operation,
it can result in incorrect data being read back from the AD7280A.
Rev. 0 | Page 44 of 48
AD7280A
If a second convert start signal is received by the AD7280A while
the conversion results are being read back, the data being read
back from the device, or chain of devices, can be corrupted. The
corruption of data occurs at the point in which the second con-
vert start signal is introduced. Any data read back prior to the
second convert start signal is correct, but data read back after
the second convert start signal may be corrupted.
to gate the convert start signal. This prevents any glitches that
CNVST
occur on the
pin from being applied directly to the
internal circuitry of the AD7280A.
SOFTWARE FLOWCHART
See Figure 41 for a software flowchart of a suggested sequence
of steps that should be considered when operating the
AD7280A in a noisy environment.
Note that the corruption of data is not limited to the conversion
result. The device address, channel address, and CRC data can
CNVST
also be corrupted. The
control register should be used
POWER UP AD7280A
CHAIN OF DEVICES
WAIT AT LEAST 5.5ms FOR ALL DEVICES
TO BE FULLY POWERED UP
WRITE TO CONTROL REGISTER
INITIALIZE DEVICE IDs ON ALL
PARTS IN THE CHAIN
TO RETURN DB1/DB2 TO
DEFAULT VALUES
NO
CHECK
HAVE ANY
PARTS IN THE
INTEGRITY OF
NOT
CHAIN INITIALIZATION
OK
PLACE CHAIN IN POWER-DOWN MODE AND
WAIT AT LEAST 2ms FOR CAPACITORS ON
CHAIN RETURNED A
RESULT OF ALL 0s FROM
THE CONTROL
YES
BY READING BACK THE LOW
BYTE OF THE CONTROL
REGISTER FROM
ALL DEVICES
V
AND V
TO DISSIPATE CHARGE
REG
REF
REGISTER?
OK
PROGRAM CONFIGURATION
REGISTERS AS REQUIRED
WRITE TO CNVST CONTROL
REGISTER TO ALLOW A SINGLE
CNVST PULSE THROUGH
INITIATE A
CONVERSION
READ BACK THE CONVERSION RESULTS FROM ALL DEVICES IN
THE DAISY-CHAIN READBACK MODE
IS THE
CRC CORRECT
FOR ALL DATA FRAMES
READ BACK?
NO
IGNORE RESPECTIVE
32-BIT FRAME
YES
DATA VALIDATION
COMPLETE
HAS THE
REQUIRED NUMBER
OF CONVERSIONS BEEN
COMPLETED?
NO
YES
POWER DOWN AD7280A
CHAIN OF DEVICES
Figure 41. Suggested Software Flowchart When Operating in a Noisy Environment
Rev. 0 | Page 45 of 48
AD7280A
OUTLINE DIMENSIONS
9.20
9.00 SQ
8.80
0.75
0.60
0.45
1.60
MAX
37
48
36
1
PIN 1
7.20
TOP VIEW
(PINS DOWN)
7.00 SQ
6.80
1.45
1.40
1.35
0.20
0.09
7°
3.5°
0°
0.08
COPLANARITY
25
12
0.15
0.05
13
24
SEATING
PLANE
0.27
0.22
0.17
VIEW A
0.50
BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BBC
Figure 42. 48-Lead Low Profile Quad Flat Package [LQFP]
(ST-48)
Dimensions shown in millimeters
ORDERING GUIDE
Model1, 2
AD7280ABSTZ
AD7280ABSTZ-RL
AD7280AWBSTZ
AD7280AWBSTZ-RL
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
48-Lead LQFP
48-Lead LQFP
48-Lead LQFP
48-Lead LQFP
Package Option
ST-48
ST-48
ST-48
ST-48
1 Z = RoHS Compliant Part.
2 W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS
The AD7280AW models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
Rev. 0 | Page 46 of 48
AD7280A
NOTES
Rev. 0 | Page 47 of 48
AD7280A
NOTES
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09435-0-4/11(0)
Rev. 0 | Page 48 of 48
相关型号:
AD7280BCPZ
IC 6-CHANNEL POWER SUPPLY SUPPORT CKT, QCC48, LEAD FREE, MO-220VKKD-2, LFCSP-48, Power Management Circuit
ADI
AD7280BSTZ
IC 6-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48, LEAD FREE, MS-026BBC, LQFP-48, Power Management Circuit
ADI
AD7280DCPZ
IC 6-CHANNEL POWER SUPPLY SUPPORT CKT, QCC48, LEAD FREE, MO-220VKKD-2, LFCSP-48, Power Management Circuit
ADI
AD7280DSTZ
IC 6-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48, LEAD FREE, MS-026BBC, LQFP-48, Power Management Circuit
ADI
AD7280WBCPZ
IC 6-CHANNEL POWER SUPPLY SUPPORT CKT, QCC48, LEAD FREE, MO-220WKKD, LFCSP-48, Power Management Circuit
ADI
AD7280WBSTZ
IC 6-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48, LEAD FREE, MS-026BBC, LQFP-48, Power Management Circuit
ADI
AD7280WDCPZ
IC 6-CHANNEL POWER SUPPLY SUPPORT CKT, QCC48, LEAD FREE, MO-220WKKD, LFCSP-48, Power Management Circuit
ADI
AD7280WDSTZ
IC 6-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48, LEAD FREE, MS-026BBC, LQFP-48, Power Management Circuit
ADI
©2020 ICPDF网 联系我们和版权申明