AD538BDZ [ADI]
Real-Time Analog Computational Unit (ACU); 实时模拟计算单元(ACU )型号: | AD538BDZ |
厂家: | ADI |
描述: | Real-Time Analog Computational Unit (ACU) |
文件: | 总17页 (文件大小:511K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Real-Time Analog
Computational Unit (ACU)
AD538
FUNCTIONAL BLOCK DIAGRAM
FEATURES
VO = VY(VZ/VX)m transfer function
I
D
X
X
25kΩ
Wide dynamic range (denominator) −1000:1
Simultaneous multiplication and division
Resistor-programmable powers and roots
No external trims required
Low input offsets <100 μV
Low error 0.2ꢀ5 of reading (100:1 range)
Monolithic construction
100Ω
V
LOG
B
A
RATIO
25kΩ
V
I
Z
Z
100Ω
INTERNAL
VOLTAGE
REFERENCE
+10V
+2V
Real-time analog multiplication, division and
exponentiation
V
I
Y
Y
High accuracy analog division with a wide input dynamic range
On board +2 V or +10 V scaling reference
Voltage and current (summing) input modes
Monolithic construction with lower cost and higher
reliability than hybrid and modular circuits
25kΩ
AD538
LOG
C
I
ANTILOG
OUTPUT
V
O
APPLICATIONS
One- or two-quadrant multiply/divide
Log ratio computation
Figure 1.
Squaring/square rooting
Trigonometric function approximations
Linearization via curve fitting
Precision AGC
Power functions
GENERAL DESCRIPTION
The AD538 is a monolithic real-time computational circuit
that provides precision analog multiplication, division, and
exponentiation. The combination of low input and output offset
voltages and excellent linearity results in accurate computation
over an unusually wide input dynamic range. Laser wafer
trimming makes multiplication and division with errors as low
as 0.25% of reading possible, while typical output offsets of
100 μV or less add to the overall off-the-shelf performance level.
Real-time analog signal processing is further enhanced by the
400 kHz bandwidth of the device.
multiplication and division can be set using the on-chip +2 V or
+10 V references, or controlled externally to provide simultaneous
multiplication and division. Exponentiation with an m value
from 0.2 to 5 can be implemented with the addition of one or
two external resistors.
Direct log ratio computation is possible by using only the log
ratio and output sections of the chip. Access to the multiple
summing junctions adds further to the flexibility of the AD538.
Finally, a wide power supply range of 4.5 V to 18 V allows
operation from standard 5 V, 12 V and 15 V supplies.
The overall transfer function of the AD538 is VO = VY(VZ/VX)m.
Programming a particular function is via pin strapping. No
external components are required for one-quadrant (positive
input) multiplication and division. Two-quadrant (bipolar
numerator) division is possible with the use of external level
shifting and scaling resistors. The desired scale factor for both
The AD538 is available in two accuracy grades (A and B) over
the industrial (−25°C to +85°C) temperature range and one
grade (S) over the military (−55°C to +125°C) temperature
range. The device is packaged in an 18-lead TO-118 hermetic
side-brazed ceramic DIP. A-grade chips are also available.
Rev. E
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2011 Analog Devices, Inc. All rights reserved.
IMPORTANT LINKS for the AD538*
Last content update 09/07/2013 05:28 pm
PARAMETRIC SELECTION TABLES
DESIGN SUPPORT
Submit your support request here:
Linear and Data Converters
Embedded Processing and DSP
Find Similar Products By Operating Parameters
Telephone our Customer Interaction Centers toll free:
DOCUMENTATION
Americas:
Europe:
China:
1-800-262-5643
00800-266-822-82
4006-100-006
AN-213: Low Cost, Two-Chip, Voltage -Controlled Amplifier and Video
Switch
India:
1800-419-0108
8-800-555-45-90
AN-304: One Chip “Slide-Rulerdquo; Works With Logs, Antilogs for
Real Time Processing
Russia:
Ask The Applications Engineer-1
Space Qualified Parts List
Quality and Reliability
Lead(Pb)-Free Data
EVALUATION KITS & SYMBOLS & FOOTPRINTS
SAMPLE & BUY
AD538
Symbols and Footprints
View Price & Packaging
Request Evaluation Board
Request Samples
Check Inventory & Purchase
DESIGN COLLABORATION COMMUNITY
Find Local Distributors
Collaborate Online with the ADI support team and other designers
about select ADI products.
Follow us on Twitter: www.twitter.com/ADI_News
Like us on Facebook: www.facebook.com/AnalogDevicesInc
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet.
Note: Dynamic changes to the content on this page (labeled 'Important Links') does not
constitute a change to the revision number of the product data sheet.
This content may be frequently modified.
AD538
TABLE OF CONTENTS
Features .............................................................................................. 1
Stability Precautions................................................................... 10
Using The Voltage References .................................................. 10
One-Quadrant Multiplication/Division.................................. 11
Two-Quadrant Division ............................................................ 12
Log Ratio Operation .................................................................. 12
Analog Computation Of Powers And Roots .......................... 13
Square Root Operation.............................................................. 13
Applications Information .............................................................. 15
Transducer Linearization .......................................................... 15
ARC-Tangent Approximation .................................................. 15
Outline Dimensions....................................................................... 16
Ordering Guide .......................................................................... 16
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Typical Performance Characteristics ............................................. 7
Theory of Operation ........................................................................ 9
Re-Examination of Multiplier/Divider Accuracy .................... 9
Functional Description.............................................................. 10
REVISION HISTORY
6/11—Rev. D to Rev. E
Updated Format..................................................................Universal
Added Table 3.................................................................................... 6
Changes to Ordering Guide .......................................................... 11
5/10—Rev. C to Rev. D
Updated Outline Dimensions....................................................... 11
Changes to Ordering Guide .......................................................... 11
Rev. E | Page 2 of 16
AD538
SPECIFICATIONS
VS = 15 V, TA = 25°C, unless otherwise noted.
Table 1.
AD538AD
Typ
AD538BD
Typ
AD538SD
Typ
Test Conditions/
Comments
Parameter
Min
Max
Min
Max
Min
Max
Unit
MULTIPLIER DIVIDER
PERFORMANCE
Nominal Transfer
Function
VO = VY(VZ/VX)m
VO = 25 kΩ × IY(IZ/IX)m
VO = VY(VZ/VX)m
VO = 25 kΩ × IY(IZ/IX)m
VO = VY(VZ/VX)m
VO = 25 kΩ × IY(IZ/IX)m
10 V ≥ VX, VY, VZ ≥ 0
400 µA ≥ IX, IY, IZ ≥ 0
100 mV ≤ VX ≤ 10 V
100 mV ≤ VY ≤ 10 V
Total Error Terms
100:1 Input
Range1
0.5
1
0.25
100
0.5
250
0.5
1
% of Reading +
µV
200
500
200
500
100 mV ≤ VZ ≤ 10 V
VZ ≤ 10 VX, m = 1.0
TA = TMIN to TMAX
1
450
1
2
750
2
0.5
350
0.5
1
500
1
1.25
750
1
2.5
1000
2
% of Reading +
µV
Wide Dynamic
Range2
100 mV ≤ VX ≤ 10 V
% of Reading +
100 mV ≤ VY ≤ 10 V
100 mV ≤ VZ ≤ 10 V
VZ ≤ 10 VX, m = 1.0
TA = TMIN to TMAX
200
100
500
250
100
750
250
150
200
200
500
250
µV
µV × (VY + VZ)/VX
1
450
450
3
750
750
1
350
350
2
500
500
2
750
750
4
1000
1000
% of Reading +
µV +
µV × (VY +
VZ)/VX
Exponent (m)
Range
TA = TMIN to TMAX
0.2
5
0.2
5
0.2
5
OUTPUT
CHARACTERISTICS
Offset Voltage
VY = 0, VC =
−600 mV
200
450
500
750
100
350
250
500
200
750
500
µV
TA = TMIN to TMAX
RL = 2 kΩ
1000
+11
µV
V
Output Voltage
Swing
−11
5
+11
−11
5
+11
−11
5
Output Current
10
10
10
mA
FREQUENCY
RESPONSE
Slew Rate
Small Signal
Bandwidth
1.4
400
1.4
400
1.4
400
V/µs
kHz
100 mV ≤ 10 VY, VZ,
VX ≤ 10 V
VOLTAGE REFERENCE
Accuracy
Additional Error
Output Current
VREF = 10 V or 2 V
TA = TMIN or TMAX
VREF = 10 V to 2 V
25
20
2.5
50
30
15
20
2.5
25
30
25
30
2.5
50
50
mV
mV
mA
1
1
1
Power Supply
Rejection
+2 V = VREF
+10 V = VREF
POWER SUPPLY
Rated
4.5 V ≤ VS ≤ 18 V
13 V ≤ VS ≤ 18 V
300
200
600
500
300
200
600
500
300
200
600
500
µV/V
µV/V
RL = 2 kΩ
15
15
15
V
Operating Range3
PSRR
4.5
18
0.1
4.5
18
0.1
4.5
18
0.1
V
%/V
4.5 V<, VS < 18 V
VX = VY = VZ = 1 V
VO = 1 V
0.5
0.5
0.5
Quiescent Current
4.5
7
4.5
7
4.5
7
mA
Rev. E | Page 3 of 16
AD538
AD538AD
Typ
AD538BD
Typ
AD538SD
Typ
Test Conditions/
Comments
Parameter
TEMPERATURE RANGE
Rated
Min
Max
Min
Max
Min
Max
Unit
−25
−65
+85
+150
−25
−65
+85
+150
−55
−65
+125
+150
°C
°C
Storage
1 Over the 100 mV to 10 V operating range total error is the sum of a percent of reading term and an output offset. With this input dynamic range the input offset
contribution to total error is negligible compared to the percent of reading error. Thus, it is specified indirectly as a part of the percent of reading error.
2 The most accurate representation of total error with low level inputs is the summation of a percent of reading term, an output offset and an input offset multiplied by
the incremental gain (VY + VZ) VX.
3 When using supplies below 13 V, the 10 V reference pin must be connected to the 2 V pin in order for the AD538 to operate correctly.
Rev. E | Page 4 of 16
AD538
ABSOLUTE MAXIMUM RATINGS
Table 2.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Parameter
Rating
Supply Voltage
18 V
Internal Power Dissipation
Output Short Circuit-to-Ground
Input Voltages VX, VY, VZ
Input Currents IX, IY, IZ, IO
Operating Temperature Range
Storage Temperature Range
Lead Temperature, Storage
Thermal Resistance
θJC
250 mW
Indefinite
(+VS − 1 V), −1 V
1 mA
−25°C to +85°C
−65°C to +150°C
60 sec, +300°C
ESD CAUTION
35°C/W
θJA
120°C/W
Rev. E | Page 5 of 16
AD538
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
I
1
2
3
4
5
6
7
8
9
18
17
16
15
A
D
Z
V
Z
B
+10V
+2V
I
X
AD538
TOP VIEW
(Not to Scale)
V
X
14 SIGNAL GND
13 PWR GND
+V
S
–V
S
12
11
10
C
V
O
I
Y
I
V
Y
Figure 2. Pin Configuration
Table 3.
Pin No. Mnemonic
Description
1
2
3
IZ
VZ
B
Current Input for the Z Multiplicand.
Voltage Input for the Z Multiplicand.
Output of the Log Ratio Differential Amplifier. This amplifier subtracts the log of the Z input from the log of the X
input, or performs the equivalent logarithmic equivalent of long division.
4
5
6
+10V
+2V
+VS
+10 V Reference Voltage Output.
+2 V Reference Voltage Output.
Positive Supply Rail.
7
–VS
Negative Rail.
8
VO
Output Voltage.
9
I
VY
IY
C
Current Input to the Output Amplifier.
Voltage Input to the Y Multiplicand.
Current Input to the Y Multiplicand.
Current Input to the Base of the Antilog Log-to-Linear Converter.
High level Power Return of the Chip.
10
11
12
13
14
15
16
17
18
PWR GND
SIGNAL GND Low Level Ground Return of the Device.
VX
IX
D
A
Voltage Input of the X Multiplicand.
Current Input of the X Input Multiplicand.
Use for Log Ratio Function.
Use for Log Ratio Function.
Rev. E | Page 6 of 16
AD538
TYPICAL PERFORMANCE CHARACTERISTICS
5
1000
800
600
400
1M
V
V
= 10V dc
Y
Z
= V +0.05 V SIN ωt
X
X
4
3
2
1
400k
100k
40k
OFFSET
200
0
% OF READING
60 80 100
TEMPERATURE (°C)
0
10k
0.01
–55 –40
–20
0
20
40
125
0.1
1
10
DENOMINATOR VOLTAGE, V – V dc
X
Figure 3. Multiplier Error vs. Temperature (100 mV < VX, VY, VZ ≤ 10 V)
Figure 6. Small Signal Bandwidth vs. Denominator Voltage (One-Quadrant
Mult/Div)
5
1000
800
600
400
1200
1000
800
6
5
4
3
2
1
4
3
2
600
400
% OF READING
OFFSET
200
0
1
0
200
0
OFFSET
80 100
% OF READING
80 100
0
–55 –40
–20
0
20
40
60
125
–55 –40
–20
0
20
40
60
125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 4. Divider Error vs. Temperature (100 mV < VX, VY, VZ ≤ 10 V)
Figure 7. Multiplier Error vs. Temperature (10 mV < VX, VY, VZ ≤ 100 mV)
1000
5
1000
800
600
400
V
V
V
= 10V
= 0V
X
Y
Z
= 5V +5V SIN ωt VOLTS
4
3
2
1
100
% OF READING
10
200
0
OFFSET
100
1
100
0
1k
10k
INPUT FREQUENCY (Hz)
100k
1M
–55 –40
–20
0
20
40
60
80
125
TEMPERATURE (°C)
Figure 5. VZ Feedthrough vs. Frequency
Figure 8. Divider Error vs. Temperature (10 mV < VX, VY, VZ ≤ 100 mV)
Rev. E | Page 7 of 16
AD538
150
5
FOR THE FREQUENCY RANGE OF 10Hz
TO 100kHz THE TOTAL rms OUTPUT
V
V
V
= 10V
X
Y
Z
= 5V +5V SIN ωt VOLTS
= 0V
NOISE, e , FOR A GIVEN BANDWIDTH
o
Bw, IS CALCULATED e = e Bw.
100
o
n
4
3
2
V
= 0.01V
X
10
1
V
= 10V
X
1
0.1
100
0
0.01
1k
10k
INPUT FREQUENCY (Hz)
100k
1M
0.1
1
10
DC OUTPUT VOLTAGE (V)
Figure 9. VY Feedthrough vs. Frequency
Figure 10. 1 kHz Output Noise Spectral Density vs. DC Output Voltage
Rev. E | Page 8 of 16
AD538
THEORY OF OPERATION
RE-EXAMINATION OF MULTIPLIER/DIVIDER ACCURACY
total error calculations for both grades over the 100:1 input
Traditionally, the accuracy (actually the errors) of analog
multipliers and dividers has been specified in terms of percent
of full scale. Thus specified, a 1% multiplier error with a 10 V
full-scale output would mean a worst-case error of +100 mV at
any level within its designated output range. While this type of
error specification is easy to test evaluate, and interpret, it can
leave the user guessing as to how useful the multiplier actually
is at low output levels, those approaching the specified error
limit (in this case) 100 mV.
range are illustrated in Table 4. This error specification format
is a familiar one to designers and users of digital voltmeters
where error is specified as a percent of reading ± a certain
number of digits on the meter readout.
For operation as a multiplier or divider over a wider dynamic
range (>100:1), the AD538 has a more detailed error specification
that is the sum of three components: a percent of reading term,
an output offset term, and an input offset term for the VY/VX log
ratio section. A sample application of this specification, taken
from Table 4, for the AD538AD with VY = 1 V, VZ = 100 mV
and VX = 10 mV would yield a maximum error of ±±.0% of
reading ±500 ꢀV ± (1 V + 100 mV)/10 mV × ±50 ꢀV or ±±.0%
of reading ±500 ꢀV ± ±2.5 mV. This example illustrates that
with very low level inputs the AD538’s incremental gain (VY +
VZ)/VX has increased to make the input offset contribution to
error substantial.
The error sources of the AD538 do not follow the percent of
full-scale approach to specification, thus it more optimally
fits the needs of the very wide dynamic range applications
for which it is best suited. Rather than as a percent of full
scale, the AD538’s error as a multiplier or divider for a 100:1
(100 mV to 10 V) input range is specified as the sum of two
error components: a percent of reading (ideal output) term
plus a fixed output offset. Following this format, the AD538AD,
operating as a multiplier or divider with inputs down to 100 mV,
has a maximum error of ±1% of reading ±500 ꢀV. Some sample
Table 4. Sample Error Calculation Chart (Worst Case)
Total Error
VY
Input
(V)
VZ
Input
(V)
VX
Input
(V)
Ideal
Output
(V)
% of Reading
Total Offset Error Error Term
Total Error
Summation
(mV)
Summation as a
% of the Ideal
Output
Term (mV)
(mV)
100
50
100:1 INPUT
RANGE
10
10
10
10
0.5
(AD)
(BD)
(AD)
(BD)
100.5
50.25
(AD)
(BD)
1.0
0.5
(AD)
(BD)
0.25
Total Error =
±± rdg
±ꢀutput VꢀS
10
0.1
0.1
10
0.5
0.25
(AD)
(BD)
100
50
(AD)
(BD)
100.5
50.25
(AD)
(BD)
1.0
0.5
(AD)
(BD)
1
1
1
1
0.5
0.25
0.5
0.25
28
16.75
(AD)
(BD)
(AD)
(BD)
(AD)
(BD)
10 )
5
1
0.5
200
100
(AD
10.5
5.25
1.5
0.75
228
(AD)
(BD)
(AD)
(BD)
(AD)
(BD)
1.05
0.5
1.5
0.75
2.28
1.17
(AD)
(BD)
(AD)
(BD)
(AD)
(BD)
(BD)
(AD)
(BD)
(AD)
(BD)
0.1
1
0.1
0.10
0.1
0.01
0.1
10
WIDE
DYNAMIC
RANGE
116.75
Total Error =
±± rdg ±
10
0.05
2
0.25
1.76
1
(AD)
(BD)
5
2.5
(AD)
(BD)
6.76
3.5
(AD)
(BD)
2.7
1.4
(AD)
(BD)
ꢀutput VꢀS
Input VꢀS
(VY + VZ)/VX
±
×
5
0.01
0.01
0.01
0.1
5
1
125.75
75.4
25.53
15.27
(AD)
(BD)
(AD)
(BD)
100
50
20
(AD)
(BD)
(AD)
(BD)
225.75
125.4
45.53
25.27
(AD)
(BD)
(AD)
(BD)
4.52
2.51
4.55
2.53
(AD)
(BD)
(AD)
(BD)
10
10
Rev. E | Page 9 of 16
AD538
FUNCTIONAL DESCRIPTION
STABILITY PRECAUTIONS
As shown in Figure 1 and Figure 11, the VZ and VX inputs
connect directly to the input log ratio amplifiers of the AD538.
This subsection provides an output voltage proportional to the
natural log of input voltage, VZ, minus the natural log of input
voltage, VX. The output of the log ratio subsection at B can be
expressed by the transfer function
At higher frequencies, the multistaged signal path of the AD538
can result in large phase shifts (as illustrated in Figure 11). If a
condition of high incremental gain exists along that path (for
example, VO = VY × VZ/VX = 10 V × 10 mV/10 mV = 10 V so
that ΔVO/ΔVX = 1000), then small amounts of capacitive feedback
from VO to the current inputs IZ or IX can result in instability.
Appropriate care should be exercised in board layout to prevent
capacitive feedback mechanisms under these conditions.
Ln Z – Ln X
VZ
VX
kT
q
VB =
ln
I
X
Ln X
M(Ln Z – Ln X)
M(Ln Z – Ln X) +Ln Y
LOG
e
where:
V
X
k is 1.3806 × 10−23 J/K.
q is 1.60219 × 10−19 C.
T is in Kelvins.
–
ANTILOG
0.2≤M≤5
BUFFER
Σ
Σ
e
+
+
+
M
The log ratio configuration may be used alone, if correctly
temperature compensated and scaled to the desired output
level (see the Applications Information section).
V
V
Z
X
I
I
Z
Z
Y
V
= V
Y
O
LOG
LOG
e
e
Ln Z
Ln Y
V
V
Y
Figure 11. Model Circuit
Under normal operation, the log-ratio output will be directly
connected to a second functional block at Input C, the antilog
subsection. This section performs the antilog according to the
transfer function:
USING THE VOLTAGE REFERENCES
A stable band gap voltage reference for scaling is included in the
AD538. It is laser-trimmed to provide a selectable voltage output of
+10 V buffered (Pin 4), +2 V unbuffered (Pin 5) or any voltages
between +2 V and +10.2 V buffered as shown in Figure 12. The
output impedance at Pin 5 is approximately 5 kΩ. Note that any
loading of this pin produces an error in the +10 V reference
voltage. External loads on the +2 V output should be greater
than 500 kΩ to maintain errors less than 1%.
q
kT
V =V e V
C
O
Y
As with the log-ratio circuit included in the AD538, the user
may use the antilog subsection by itself. When both subsections
are combined, the output at B is tied to C, the transfer function
of the AD538 computational unit is:
I
V
V
kT
q
kT
1
2
3
4
5
6
18
17
16
15
14
13
12
11
A
D
Z
Z
Z
X
ln
Q
e
;VB =VC
LOG
RATIO
25kΩ
VO = VY
V
+2V TO +10.2V
BUFFERED
which reduces to:
B
I
X
VZ
VX
REF OUT
V
X
VO = VY
25kΩ
100Ω
100Ω
+2V
SIGNAL
GND
50kΩ
Finally, by increasing the gain, or attenuating the output of the
log ratio subsection via resistor programming, it is possible to
raise the quantity VZ/VX to the mth power. Without external
programming, m is unity. Thus, the overall AD538 transfer
function equals:
INTERNAL
VOLTAGE
REFERENCE
11.5kΩ
PWR
GND
+V
S
AD538
–V
S
7
8
9
C
OUTPUT
25kΩ
V
O
I
Y
ANTILOG
m
VZ
VX
10
V
Y
I
LOG
VO = VY
25kΩ
Figure 12. +2 V to +10.2 V Adjustable Reference
where 0.2 < m < 5.
In situations not requiring both reference levels, the +2 V output
can be converted to a buffered output by tying Pin 4 and Pin 5
together. If both references are required simultaneously, the
+10 V output should be used directly and the +2 V output
should be externally buffered.
When the AD538 is used as an analog divider, the VY input can
be used to multiply the ratio VZ/VX by a convenient scale factor.
The actual multiplication by the VY input signal is accomplished
by adding the log of the VY input signal to the signal at C, which
is already in the log domain.
Rev. E | Page 10 of 16
AD538
When the input VX is tied to the +10 V reference terminal, the
multiplier transfer function becomes:
ONE-QUADRANT MULTIPLICATION/DIVISION
Figure 13 shows how the AD538 may be easily configured
as a precision one-quadrant multiplier/divider. The transfer
function VO = VY (VZ/VX) allows three independent input
variables, a calculation not available with a conventional
multiplier. In addition, the 1000:1 (that is, 10 mV to 10 V)
input dynamic range of the AD538 greatly exceeds that of
analog multipliers computing one-quadrant multiplication
and division.
VZ
10 V
VO = VY
As a multiplier, this circuit provides a typical bandwidth of 400 kHz
with values of VX, VY, or VZ varying over a 100:1 range (that is,
100 mV to 10 V). The maximum error with a 100 mV to 10 V
range for the two input variables will typically be +0.5% of
reading. Using the optional Z offset trim scheme, as shown in
Figure 14, this error can be reduced to +0.25% of reading.
V
V
Z
X
V
= V
Y
O
By using the 10 V reference as the VY input, the circuit of
Figure 13 is configured as a one-quadrant divider with a fixed
scale factor. As with the one-quadrant multiplier, the inputs
accept only single (positive) polarity signals. The output of the
one-quadrant divider with a +10 V scale factor is:
I
1
2
3
4
5
6
18
17
16
15
14
13
12
11
A
D
Z
Z
LOG
V
25kΩ
V
Z
RATIO
INPUT
B
I
X
V
X
V
X
VZ
VX
+10V
+2V
INPUT
25kΩ
VO = 10 V
100Ω
100Ω
SIGNAL
GND
PWR
GND
INTERNAL
The typical bandwidth of this circuit is 370 kHz with 1 V to
10 V denominator input levels. At lower amplitudes, the band-
width gradually decreases to approximately 200 kHz at the
2 mV input level.
VOLTAGE
+15V
REFERENCE
AD538
C
7
8
9
–15V
OUTPUT
IN4148
25kΩ
I
V
Y
O
ANTILOG
OUTPUT
V
V
Y
Y
10
I
LOG
INPUT
25kΩ
Figure 13. One-Quadrant Combination Multiplier/Divider
By simply connecting the input, VX (Pin 15) to the 10 V
reference (Pin 4), and tying the log-ratio output at B to the
antilog input at C, the AD538 can be configured as a one-
quadrant analog multiplier with 10 V scaling. If 2 V scaling
is desired, VX can be tied to the 2 V reference.
Rev. E | Page 11 of 16
AD538
TWO-QUADRANT DIVISION
LOG RATIO OPERATION
The two-quadrant linear divider circuit illustrated in Figure 14
uses the same basic connections as the one-quadrant version.
However, in this circuit the numerator has been offset in the
positive direction by adding the denominator input voltage
to it. The offsetting scheme changes the divider’s transfer
function from
Figure 15 shows the AD538 configured for computing the log
of the ratio of two input voltages (or currents). The output
signal from B is connected to the summing junction of the
output amplifier via two series resistors. The 90.9 Ω metal film
resistor effectively degrades the temperature coefficient of the
3500 ppm/°C resistor to produce a 1.09 kΩ +3300 ppm/°C
equivalent value. In this configuration, the VY input must
be tied to some voltage less than zero (−1.2 V in this case)
removing this input from the transfer function.
VZ
VX
VO =10 V
to
The 5 kΩ potentiometer controls the circuit’s scale factor
adjustment providing a +1 V per decade adjustment. The
output offset potentiometer should be set to provide a zero
output with VX = VZ = 1 V. The input V Z adjustment should
be set for an output of 3 V with VZ = l mV and VX = 1 V.
(
VZ + AVX
)
VZ
VX
VO =10V
=10V 1A+
VX
VZ
VX
=10A +10V
–V
S
68kΩ
5%
V
V
Z
where:
V
= 1V LOG
10
O
X
AD589
–1.2V
35kΩ
25kΩ
A=
10MΩ
I
Z
A
D
1
2
3
4
5
6
18
17
16
15
14
13
12
11
1MΩ
48.7Ω
OPTIONAL
INPUT V
V
LOG
25kΩ
Z
RATIO
OS
As long as the magnitude of the denominator input is equal
to or greater than the magnitude of the numerator input, the
circuit accepts bipolar numerator voltages. However, under
the conditions of a 0 V numerator input, the output would
incorrectly equal +14 V. The offset can be removed by connecting
the 10 V reference through Resistors R1 and R2 to the output
section’s summing Node I at Pin 9 thus providing a gain of 1.4
at the center of the trimming potentiometer. The potentiometer,
R2, adjusts out or corrects this offset, leaving the desired
transfer function of 10 V (VZ/VX).
ADJUSTMENT
B
I
X
90.9Ω
V
+10V
+2V
X
V
X
INPUT
1%
25kΩ
100Ω
100Ω
SIGNAL
GND
1k
+3500
ppm/°C
PWR
GND
INTERNAL
VOLTAGE
+15V
–15V
REFERENCE
AD538
OUTPUT
C
7
8
9
OUTPUT
5kΩ 2kΩ
25kΩ
1%
V
O
I
Y
ANTILOG
SCALE
FACTOR
ADJUST
IN4148
V
I
Y
10
LOG
NUMERATOR
DENOMINATOR
25kΩ
V
V
OPTIONAL
Z
X
+V
–V
Z OFFSET TRIM
S
OPTIONAL
10MΩ
–V
S
10kΩ
OUTPUT V
OS
ADJUSTMENT
V
V
Z
S
V
= 10
FOR V ≥ V
X Z
O
68kΩ
35kΩ
X
AD589
Figure 15. Log Ratio Circuit
–1.2V
10MΩ
I
Z
Z
1MΩ
ADJ
1
2
3
4
5
6
18
17
16
15
14
13
12
11
A
D
The log ratio circuit shown achieves 0.5% accuracy in the log
domain for input voltages within three decades of input range:
10 mV to 10 V. This error is not defined as a percent of full-
scale output, but as a percent of input. For example, using a
1 V/decade scale factor, a 1% error in the positive direction
at the input of the log ratio amplifier translates into a 4.3 mV
deviation from the ideal OUTPUT (that is, 1 V × log10 (1.01) =
4.3214 mV). An input error 1% in the negative direction is
slightly different, giving an output deviation of 4.3648 mV.
V
OS
35kΩ
25kΩ
LOG
3.9MΩ
V
RATIO
I
X
B
+10V
V
X
25kΩ
100Ω
100Ω
SIGNAL
GND
+2V
PWR
GND
INTERNAL
VOLTAGE
+15V
REFERENCE
AD538
IN4148
C
7
8
9
–15V
OUTPUT
25kΩ
I
V
Y
O
OUTPUT
ANTILOG
R2
R1
10kΩ 12.4kΩ
V
I
Y
10
LOG
25kΩ
ZERO
ADJUST
Figure 14. Two-Quadrant Division with 10 V Scaling
Rev. E | Page 12 of 16
AD538
ANALOG COMPUTATION OF POWERS AND ROOTS
SQUARE ROOT OPERATION
It is often necessary to raise the quotient of two input signals to
a power or take a root. This could be squaring, cubing, square
rooting or exponentiation to some noninteger power. Examples
include power series generation. With the AD538, only one or
two external resistors are required to set any desired power, over
the range of 0.2 to 5. Raising the basic quantity VZ/VX to a
power greater than one requires that the gain of the AD538’s log
ratio subtractor be increased, via an external resistor between
the A and D pins. Similarly, a voltage divider that attenuates the
log ratio output between Point B and Point C will program the
power to a value less than one.
The explicit square root circuit of Figure 17 illustrates a precise
method for performing a real-time square root computation.
For added flexibility and accuracy, this circuit has a scale factor
adjustment.
The actual square rooting operation is performed in this circuit
by raising the quantity VZ/VX to the one-half power via the
resistor divider network consisting of resistors RB and RC. For
maximum linearity, the two resistors should be 1% (or better)
ratio-matched metal film types.
1 V scaling is achieved by dividing-down the 2 V reference
and applying approximately 1 V to both the VY and VX inputs.
In this circuit, the VX input is intentionally set low, to about
0.95 V, so that the VY input can be adjusted high, permitting
a 5% scale factor trim. Using this trim scheme, the output
voltage will be within 3 mV 0.2% of the ideal value over a
10 V to 1 mV input range (80 dB). For a decreased input dynamic
range of 10 mV to 10 V (60 dB) the error is even less; here the
output will be within 2 mV 0.2% of the ideal value. The
bandwidth of the AD538 square root circuit is approximately
280 kHz with a 1 V p-p sine wave with a +2 V dc offset.
R
A
B
C
A
D
POWERS
3
12
18
17
V
V
2
Z
m
R
A
V
Z
m
V
(
)
V
8
Y
O
2
3
4
5
196Ω
97.6Ω
64.9Ω
48.7Ω
V
REF
10
Y
15
V
V
X
REF
196Ω
M – 1
R
=
A
R
= R ≤ 200Ω
B
C
R
R
C
B
B
2
C
This basic circuit may also be used to compute the cube, fourth
or fifth roots of an input waveform. All that is required for a
given root is that the correct ratio of resistors, R
C and RB, be
ROOTS
3
12
V
V
Z
m
R
R
C
B
V
Z
m
V
8
V
(
)
O
1/2
100Ω
100Ω
150Ω
162Ω
100Ω
49.9Ω
49.9Ω
40.2Ω
Y
V
REF
1/3
1/4
1/5
10
Y
selected such that their sum is between 150 Ω and 200 Ω.
15
V
V
X
REF
The optional absolute value circuit shown preceding the AD538
allows the use of bipolar input voltages. Only one op amp is
required for the absolute value function because the IZ input of
the AD538 functions as a summing junction. If it is necessary to
preserve the sign of the input voltage, the polarity of the op amp
output may be sensed and used after the computation to switch
the sign bit of a DVM chip.
R
1
B
=
–1
R
M
C
Figure 16. Basic Configurations and Transfer Functions for the AD538
Rev. E | Page 13 of 16
AD538
V
IN
1V
V
= 1V
O
OPTIONAL
ABSOLUTE VALUE SECTION
5kΩ
I
10kΩ
Z
Z
1
2
3
4
5
6
7
8
9
18
17
16
15
14
13
12
11
10
A
D
20kΩ
LOG
V
25kΩ
IN4148 IN4148
RATIO
R
100Ω
B
+V
7
S
*
B
+10V
+2V
I
X
V
20kΩ
OS
V
X
1
20kΩ
2
V
8
6
25kΩ
IN
100Ω
100Ω
SIGNAL
GND
3
+2V
4
S
AD OP-07
OR AD811
PWR
GND
INTERNAL
VOLTAGE
(V TAP
OS
TO –V
–V
+15V
–15V
)
REFERENCE
AD538
S
C
OUTPUT
25kΩ
I
V
O
Y
V
O
ANTILOG
D1
IN4148
V
I
Y
LOG
1kΩ
25kΩ
100Ω
SCALE FACTOR
TRIM
R
100Ω
C
1kΩ
*
*
RATIO MATCH 1% METAL FILM
RESISTORS FOR BEST ACCURACY
Figure 17. Square Root Circuit
Rev. E | Page 14 of 16
AD538
APPLICATIONS INFORMATION
The (VθREF − Vθ) function is implemented in this circuit by
TRANSDUCER LINEARIZATION
adding together the output, Vθ, and an externally applied
reference voltage, VθREF, via an external AD547 op amp. The
1 μF capacitor connected around the AD547’s 100 kΩ feedback
resistor frequency compensates the loop (formed by the amplifier
between Vθ and VY).
Many electronic transducers used in scientific, commercial or
industrial equipment monitor the physical properties of a device
and/or its environment. Sensing (and perhaps compensating for)
changes in pressure, temperature, moisture or other physical
phenomenon can be an expensive undertaking, particularly
where high accuracy and very low nonlinearity are important.
In conventional analog systems accuracy may be easily increased
by offset and scale factor trims; however, nonlinearity is usually
the absolute limitation of the sensing device.
1.21
V
V
Z
X
Z
X
–1
θ = TAN
V
= [V
θREF
–V ] ×
θ
θ
A
D
I
1
2
3
4
5
6
7
8
9
18
17
16
15
14
13
12
11
10
Z
Z
R
A
V
931Ω, 1%
LOG
RATIO
25kΩ
V
Z
With the ability to easily program a complex analog function,
the AD538 can effectively compensate for the nonlinearities
of an inexpensive transducer. The AD538 can be connected
between the transducer preamplifier output and the next stage
of monitoring or transmitting circuitry. The recommended
procedure for linearizing a particular transducer is first to find
the closest function which best approximates the nonlinearity
of the device and then, to select the appropriate exponent
resistor value(s).
B
I
X
V
+10V
X
V
X
25kΩ
100Ω
100Ω
SIGNAL
GND
+2V
INTERNAL
VOLTAGE
REFERENCE
PWR
GND
+V
–V
V
S
S
+15V
–15V
AD538
1µF
1µF
C
OUTPUT
IN4148
25kΩ
I
Y
O
I
V
θ
ANTILOG
V
Y
LOG
ARC-TANGENT APPROXIMATION
25kΩ
The circuit of Figure 18 is typical of those AD538 applications
where the quantity VZ/VX is raised to powers greater than one.
In an approximate arc-tangent function, the AD538 will accurately
compute the angle that is defined by X and Y displacements
represented by input voltages VX and VZ. With accuracy to
within one degree (for input voltages between 100 μV and
10 V), the AD538 arc-tangent circuit is more precise than
conventional analog circuits and is faster than most digital
techniques. The circuit shown is set up for the transfer
function:
0.1µF
+15V
R2*
R1*
100kΩ
100kΩ
7
2
3
10kΩ
FULL-SCALE
ADJUST
6
AD547JH
118kΩ
*
RATIO MATCH 1% METAL
FILM RESISTORS FOR BEST
ACCURACY
4
1µF
100kΩ
–15V
Figure 18. The Arc-Tangent Function
The VB/VA quantity is calculated in the same manner as in the
one-quadrant divider circuit, except that the resulting quotient
is raised to the 1.21 power. Resistor RA (nominally 931 Ω) sets
the power or m factor.
1.21
(
VZ
)
)
Vθ =
(
VθREF −Vθ
)
(VX
For the highest arc-tangent accuracy the R1 and R2 external
resistors should be ratio matched; however, the offset trim scheme
shown in other circuits is not required since nonlinearity effects
are the predominant source of error. Also note that instability
will occur as the output approaches 90° because, by definition,
the arc-tangent function is infinite and therefore, the gain of the
AD538 will be extremely high.
where:
θ=Tan−1
Z
X
Rev. E | Page 15 of 16
AD538
OUTLINE DIMENSIONS
0.005 (0.13) MIN
18
0.098 (2.49) MAX
10
0.310 (7.87)
PIN 1
1
0.220 (5.59)
9
0.320 (8.13)
0.290 (7.37)
0.960 (24.38) MAX
0.060 (1.52)
0.015 (0.38)
0.200 (5.08)
MAX
0.150
(3.81)
MIN
0.200 (5.08)
0.125 (3.18)
0.015 (0.38)
0.008 (0.20)
SEATING
PLANE
0.100 0.070 (1.78)
(2.54)
0.030 (0.76)
0.023 (0.58)
0.014 (0.36)
BSC
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 19. 18-Lead Side-Brazed Ceramic Dual In-Line Package [SBDIP]
(D-18)
Dimensions shown in inches and (millimeters)
ORDERING GUIDE
Model1
Temperature Range
Package Description
Package Option
AD538ACHIPS
AD538AD
AD538ADZ
AD538BD
AD538BDZ
AD538SD
AD538SD/883B
−25°C to +85°C
−25°C to +85°C
−25°C to +85°C
−25°C to +85°C
−25°C to +85°C
−55°C to +125°C
−55°C to +125°C
Chips
18-Lead Side-Brazed Ceramic Dual In-Line Package [SBDIP]
18-Lead Side-Brazed Ceramic Dual In-Line Package [SBDIP]
18-Lead Side-Brazed Ceramic Dual In-Line Package [SBDIP]
18-Lead Side-Brazed Ceramic Dual In-Line Package [SBDIP]
18-Lead Side-Brazed Ceramic Dual In-Line Package [SBDIP]
18-Lead Side-Brazed Ceramic Dual In-Line Package [SBDIP]
D-18
D-18
D-18
D-18
D-18
D-18
1 Z = RoHS Compliant Part.
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00959-0-6/11(E)
Rev. E | Page 16 of 16
相关型号:
AD538SD
ANALOG MULTIPLE FUNCTIONS, 0.4 MHz BAND WIDTH, CDIP18, SIDE BRAZED, CERAMIC, DIP-18
ROCHESTER
AD5390BCP
IC SERIAL INPUT LOADING, 8 us SETTLING TIME, 14-BIT DAC, QCC64, 9 X 9 MM, LFCSP-64, Digital to Analog Converter
ADI
AD5390BCP-3
8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
ADI
AD5390BCP-3-REEL
8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
ADI
AD5390BCP-3-REEL7
8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
ADI
AD5390BCP-5
8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
ADI
AD5390BCP-5-REEL
8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
ADI
©2020 ICPDF网 联系我们和版权申明