AD1939YSTZRL [ADI]
4 ADC/8 DAC with PLL, 192 kHz, 24-Bit CODEC; 4 ADC / DAC 8与PLL , 192千赫, 24位编解码器型号: | AD1939YSTZRL |
厂家: | ADI |
描述: | 4 ADC/8 DAC with PLL, 192 kHz, 24-Bit CODEC |
文件: | 总32页 (文件大小:438K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
4 ADC/8 DAC with PLL,
192 kHz, 24-Bit CODEC
AD1939
GENERAL DESCRIPTION
FEATURES
The AD1939 is a high performance, single-chip codec that
provides four analog-to-digital converters (ADCs) with
differential input and eight digital-to-analog converters (DACs)
with differential output using the Analog Devices, Inc. patented
multibit sigma-delta (Σ-Δ) architecture. An SPI port is included,
allowing a microcontroller to adjust volume and many other
parameters. The AD1939 operates from 3.3 V digital and analog
supplies. The AD1939 is available in a 64-lead (differential
output) LQFP package.
PLL generated or direct master clock
Low EMI design
112 dB DAC/107 dB ADC dynamic range and SNR
−94 dB THD + N
Single 3.3 V supply
Tolerance for 5 V logic inputs
Supports 24-bits and 8 kHz to 192 kHz sample rates
Differential ADC input
Differential DAC output
Log volume control with autoramp function
SPI® controllable for flexibility
Software controllable clickless mute
Software power-down
Right-justified, left-justified, I2S, and TDM modes
Master and slave modes up to 16-channel in/out
64-lead LQFP package
The AD1939 is designed for low EMI. This consideration is
apparent in both the system and circuit design architectures.
By using the on-board PLL to derive the master clock from the
LR clock or from an external crystal, the AD1939 eliminates
the need for a separate high frequency master clock and can
also be used with a suppressed bit clock. The digital-to-analog
and analog-to-digital converters are designed using the latest
ADI continuous time architectures to further minimize EMI.
By using 3.3 V supplies, power consumption is minimized,
further reducing emissions.
APPLICATIONS
Automotive audio systems
Home Theater Systems
Set-top boxes
Digital audio effects processors
FUNCTIONAL BLOCK DIAGRAM
DIGITAL AUDIO
INPUT/OUTPUT
AD1939
SERIAL DATA PORT
DAC
DAC
DAC
DAC
DAC
DAC
DAC
DAC
SDATA
OUT
SDATA
IN
ADC
ADC
ADC
ADC
DIGITAL
FILTER
AND
VOLUME
CONTROL
ANALOG
AUDIO
INPUTS
CLOCKS
ANALOG
AUDIO
OUTPUTS
DIGITAL
FILTER
TIMING MANAGEMENT
AND CONTROL
(CLOCK AND PLL)
CONTROL PORT
2
PRECISION
VOLTAGE
REFERENCE
SPI/I C
CONTROL DATA
INPUT/OUTPUT
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2006 Analog Devices, Inc. All rights reserved.
AD1939
TABLE OF CONTENTS
Features .............................................................................................. 1
Analog-to-Digital Converters (ADCs).................................... 13
Digital-to-Analog Converters (DACs).................................... 13
Clock Signals............................................................................... 13
Reset and Power-Down ............................................................. 14
Serial Control Port ..................................................................... 14
Power Supply and Voltage Reference....................................... 15
Serial Data Ports—Data Format............................................... 15
Time-Division Multiplexed (TDM) Modes............................ 15
Daisy-Chain Mode..................................................................... 19
Control Registers............................................................................ 24
Definitions................................................................................... 24
PLL and Clock Control Registers............................................. 24
DAC Control Registers .............................................................. 25
ADC Control Registers.............................................................. 27
Additional Modes....................................................................... 29
Application Circuits ....................................................................... 30
Outline Dimensions....................................................................... 31
Ordering Guide .......................................................................... 31
Applications....................................................................................... 1
General Description......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Test Conditions............................................................................. 3
Analog Performance Specifications........................................... 3
Crystal Oscillator Specifications................................................. 4
Digital Input/Output Specifications........................................... 5
Power Supply Specifications........................................................ 5
Digital Filters................................................................................. 6
Timing Specifications .................................................................. 6
Absolute Maximum Ratings............................................................ 8
Thermal Resistance ...................................................................... 8
ESD Caution.................................................................................. 8
Pin Configuration and Function Descriptions............................. 9
Typical Performance Characteristics ........................................... 11
Theory of Operation ...................................................................... 13
REVISION HISTORY
7/06—Revision 0: Initial Version
Rev. 0 | Page 2 of 32
AD1939
SPECIFICATIONS
TEST CONDITIONS
Performance of all channels is identical, exclusive of the interchannel gain mismatch and interchannel phase deviation specifications.
Supply voltages (AVDD, DVDD)
Temperature range1
Master clock
3.3 V
as specified in Table 1 and Table 2
12.288 MHz (48 kHz fS, 256 × fS mode)
Input sample rate
48 kHz
Measurement bandwidth
Word width
20 Hz to 20 kHz
24 bits
Load capacitance (digital output)
Load current (digital output)
Input voltage HI
20 pF
1 mA or 1.5 kΩ to ½ DVDD supply
2.0 V
0.8 V
Input voltage LO
1 Functionally guaranteed at −40°C to +125°C case temperature.
ANALOG PERFORMANCE SPECIFICATIONS
Specifications guaranteed at 25°C (ambient).
Table 1.
Parameter
Conditions/Comments
Min
Typ
Max
Unit
ANALOG-TO-DIGITAL CONVERTERS
ADC Resolution
All ADCs
24
Bits
Dynamic Range
20 Hz to 20 kHz, −60 dB input
No Filter (RMS)
96
98
102
105
−96
dB
dB
dB
%
With A-Weighted Filter (RMS)
Total Harmonic Distortion + Noise
Gain Error
−1 dBFS
−87
+10
−10
Interchannel Gain Mismatch
Offset Error
Gain Drift
Interchannel Isolation
CMRR
−0.25
−10
+0.25
+10
dB
0
mV
ppm/°C
dB
dB
dB
100
−110
55
100 mV rms, 1 kHz
100 mV rms, 20 kHz
55
Input Resistance
Input Capacitance
14
10
kΩ
pF
Input Common-Mode Bias Voltage
DIGITAL-TO-ANALOG CONVERTERS
Dynamic Range
1.5
V
20 Hz to 20 kHz, −60 dB input
No Filter (RMS)
102
105
107
110
112
dB
dB
dB
With A-Weighted Filter (RMS)
With A-Weighted Filter (Avg)
Total Harmonic Distortion + Noise
0 dBFS
Two channels running
Eight channels running
−94
−86
dB
dB
−76
Full-Scale Output Voltage
Gain Error
Interchannel Gain Mismatch
Offset Error
Gain Drift
Interchannel Isolation
Interchannel Phase Deviation
1.76 (4.96)
V rms (V p-p)
%
dB
mV
ppm/°C
dB
Degrees
−10
−0.2
−25
−30
+10
+0.2
+25
+30
−6
100
0
Rev. 0 | Page 3 of 32
AD1939
Parameter
Conditions/Comments
Min
Typ
0.375
95
Max
Unit
dB
dB
dB
Ω
Volume Control Step
Volume Control Range
De-emphasis Gain Error
Output Resistance at Each Pin
REFERENCE
0.6
100
Internal Reference Voltage
External Reference Voltage
Common-Mode Reference Output
REGULATOR
FILTR pin
FILTR pin
CM pin
1.50
1.50
1.50
V
V
V
1.32
1.68
Input Supply Voltage
Regulated Output Voltage
VSUPPLY pin
VSENSE pin
4.5
3.19
5
3.37
5.5
3.55
V
V
Specifications measured at 130°C (case).
Table 2.
Parameter
Conditions/Comments
Min
Typ
Max
Unit
ANALOG-TO-DIGITAL CONVERTERS
ADC Resolution
All ADCs
24
Bits
Dynamic Range
20 Hz to 20 kHz, −60 dB input
No Filter (RMS)
93
96
102
104
−96
dB
dB
dB
%
With A-Weighted Filter (RMS)
Total Harmonic Distortion + Noise
Gain Error
−1 dBFS
−87
+10
−10
Interchannel Gain Mismatch
Offset Error
−0.25
−10
+0.25
+10
dB
mV
0
DIGITAL-TO-ANALOG CONVERTERS
Dynamic Range
20 Hz to 20 kHz, −60 dB input
No Filter (RMS)
101
104
107
110
112
dB
dB
dB
With A-Weighted Filter (RMS)
With A-Weighted Filter (Average)
Total Harmonic Distortion + Noise
0 dBFS
Two channels running
Eight channels running
−94
−86
dB
dB
−70
Full-Scale Output Voltage
Gain Error
Interchannel Gain Mismatch
Offset Error
1.76 (4.96)
V rms (V p-p)
%
dB
mV
−10
−0.2
−25
−30
+10
+0.2
+25
+30
−6
Gain Drift
ppm/°C
REFERENCE
Internal Reference Voltage
External Reference Voltage
Common-Mode Reference Output
REGULATOR
FILTR pin
FILTR pin
CM pin
1.50
1.50
1.50
V
V
V
1.32
1.68
Input Supply Voltage
Regulated Output Voltage
VSUPPLY pin
VSENSE pin
4.5
3.2
5
3.43
5.5
3.65
V
V
CRYSTAL OSCILLATOR SPECIFICATIONS
Table 3.
Parameter
Min
Typ
Max
Unit
Transconductance
3.5
mmhos
Rev. 0 | Page 4 of 32
AD1939
DIGITAL INPUT/OUTPUT SPECIFICATIONS
−40°C < TA < +130°C, DVDD = 3.3 V 10ꢀ.
Table 4.
Parameter
Conditions/Comments
Min
2.0
2.2
Typ
Max
Unit
V
V
Input Voltage HI (VIH)
Input Voltage HI (VIH)
Input Voltage LO (VIL)
Input Leakage
MCLKI/XI pin
0.8
10
10
V
IIH @ VIH = 2.4 V
IIL @ VIL = 0.8 V
IOH = 1 mA
μA
μA
V
V
pF
High Level Output Voltage (VOH)
Low Level Output Voltage (VOL)
Input Capacitance
DVDD − 0.60
IOL = 1 mA
0.4
5
POWER SUPPLY SPECIFICATIONS
Table 5.
Parameter
SUPPLIES
Voltage
Conditions/Comments
Min
Typ
Max
Unit
DVDD
AVDD
3.0
3.0
3.3
3.3
3.6
3.6
V
V
Digital Current
Normal Operation
MCLK = 256 fS
fS = 48 kHz
fS = 96 kHz
fS = 192 kHz
fS = 48 kHz to 192 kHz
56
65
95
2.0
mA
mA
mA
mA
Power-Down
Analog Current
Normal Operation
Power-Down
74
23
mA
mA
DISSIPATION
Operation
MCLK = 256 fS, 48 kHz
All Supplies
Digital Supply
Analog Supply
429
185
244
83
mW
mW
mW
mW
Power-Down, All Supplies
POWER SUPPLY REJECTION RATIO
Signal at Analog Supply Pins
1 kHz 200 mV p-p
20 kHz 200 mV p-p
50
50
dB
dB
Rev. 0 | Page 5 of 32
AD1939
DIGITAL FILTERS
Table 6.
Parameter
Mode
Factor
Min
Typ
Max
Unit
ADC DECIMATION FILTER
Pass Band
All modes, typ @ 48 kHz
0.4375 fS
21
0.015
kHz
dB
Pass-Band Ripple
Transition Band
Stop Band
Stop-Band Attenuation
Group Delay
0.5 fS
0.5625 fS
24
27
kHz
kHz
dB
79
35
22.9844/fS
479
22
μs
DAC INTERPOLATION FILTER
Pass Band
48 kHz mode, typ @ 48 kHz
96 kHz mode, typ @ 96 kHz
192 kHz mode, typ @ 192 kHz
48 kHz mode, typ @ 48 kHz
96 kHz mode, typ @ 96 kHz
192 kHz mode, typ @ 192 kHz
48 kHz mode, typ @ 48 kHz
96 kHz mode, typ @ 96 kHz
192 kHz mode, typ @ 192 kHz
48 kHz mode, typ @ 48 kHz
96 kHz mode, typ @ 96 kHz
192 kHz mode, typ @ 192 kHz
48 kHz mode, typ @ 48 kHz
96 kHz mode, typ @ 96 kHz
192 kHz mode, typ @ 192 kHz
48 kHz mode, typ @ 48 kHz
96 kHz mode, typ @ 96 kHz
192 kHz mode, typ @ 192 kHz
0.4535 fS
0.3646 fS
0.3646 fS
kHz
kHz
kHz
dB
dB
dB
kHz
kHz
kHz
kHz
kHz
kHz
dB
70
Pass-Band Ripple
Transition Band
Stop Band
0.01
0.05
0.1
0.5 fS
0.5 fS
0.5 fS
0.5465 fS
0.6354 fS
0.6354 fS
24
48
96
26
61
122
Stop-Band Attenuation
Group Delay
70
70
70
dB
dB
μs
μs
25/fS
11/fS
8/fS
521
115
42
μs
TIMING SPECIFICATIONS
−40°C < TA < +130°C, DVDD = 3.3 V 10ꢀ.
Table 7.
Parameter
Condition
Comments
Min
Max Unit
INPUT MASTER CLOCK (MCLK)
AND RESET
tMH
MCLK duty cycle
DAC/ADC clock source = PLL clock @ 256 fS, 384 fS,
512 fS, 768 fS
DAC/ADC clock source = direct MCLK @ 512 fS (bypass
on-chip PLL)
PLL mode, 256 fS reference
Direct 512 fS mode
40
40
6.9
60
60
%
%
tMH
fMCLK
fMCLK
tPDR
MCLK frequency
13.8 MHz
27.6 MHz
ns
Low
15
tPDRR
Recovery
Reset to active output
4096
tMCLK
PLL
Lock time
MCLK and LRCLK
input
10
60
ms
%
256 fS VCO Clock
Output Duty Cycle
MCLKO/XO pin
40
Rev. 0 | Page 6 of 32
AD1939
Parameter
Condition
Comments
Min
Max Unit
SPI PORT
See Figure 11
tCCH
tCCL
CCLK high
CCLK low
35
35
ns
ns
fCCLK
tCDS
tCDH
tCLS
CCLK frequency
CDATA setup
CDATA hold
CLATCH setup
CLATCH hold
CLATCH high
COUT enable
COUT delay
COUT hold
fCCLK = 1/tCCP; only tCCP shown in Figure 11
To CCLK rising
From CCLK rising
10
MHz
ns
ns
ns
10
10
10
10
10
To CCLK rising
tCLH
From CCLK falling
ns
ns
tCLHIGH
Not shown in Figure 11
From CCLK falling
From CCLK falling
From CCLK falling, not shown in Figure 11
From CCLK falling
tCOE
tCOD
tCOH
tCOTS
30
30
ns
ns
ns
30
COUT tri-state
30
ns
DAC SERIAL PORT
See Figure 24
tDBH
tDBL
tDLS
tDLH
tDLS
tDDS
tDDH
DBCLK high
DBCLK low
Slave mode
Slave mode
To DBCLK rising, slave mode
From DBCLK rising, slave mode
From DBCLK falling, master mode
To DBCLK rising
10
10
10
5
−8
10
5
ns
ns
ns
ns
ns
ns
ns
DLRCLK setup
DLRCLK hold
DLRCLK skew
DSDATA setup
DSDATA hold
+8
From DBCLK rising
ADC SERIAL PORT
See Figure 25
tABH
tABL
tALS
tALH
tALS
tABDD
ABCLK high
ABCLK low
ALRCLK setup
ALRCLK hold
ALRCLK skew
ASDATA delay
Slave mode
Slave mode
To ABCLK rising, slave mode
From ABCLK rising, slave mode
From ABCLK falling, master mode
From ABCLK falling
10
10
10
5
ns
ns
ns
ns
ns
ns
−8
+8
18
AUXILIARY INTERFACE
tAXDS
tAXDH
tDXDD
tXBH
tXBL
tDLS
AAUXDATA setup
AAUXDATA hold
DAUXDATA delay
AUXBCLK high
AUXBCLK low
To AUXBCLK rising
From AUXBCLK rising
From AUXBCLK falling
10
5
ns
ns
ns
ns
ns
ns
ns
18
10
10
10
5
AUXLRCLK setup
AUXLRCLK hold
To AUXBCLK rising
From AUXBCLK rising
tDLH
Rev. 0 | Page 7 of 32
AD1939
ABSOLUTE MAXIMUM RATINGS
Table 8.
THERMAL RESISTANCE
Parameter
Rating
θJA represents thermal resistance, junction-to-ambient;
θJC represents the thermal resistance, junction-to-case.
All characteristics are for a 4-layer board.
Analog (AVDD)
Digital (DVDD)
VSUPPLY
Input Current (Except Supply Pins)
Analog Input Voltage (Signal Pins)
Digital Input Voltage (Signal Pins)
−0.3 V to +3.6 V
−0.3 V to +3.6 V
−0.3 V to +6.0 V
20 ꢀA
–0.3 V to AVDD + 0.3 V
−0.3 V to DVDD + 0.3 V
Table 9. Thermal Resistance
Package Type
θJA
θJC
Unit
64-lead LQFP
47
11.1
°C/W
Operating Teꢀperature Range (Case) −40°C to +125°C
Storage Teꢀperature Range −65°C to +150°C
Stresses above those listed under the Absolute Maximum
Ratings may cause permanent damage to the device. This is a
stress rating only; functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accuꢀulate on
the huꢀan body and test equipꢀent and can discharge without detection. Although this product features
proprietary ESD protection circuitry, perꢀanent daꢀage ꢀay occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recoꢀꢀended to avoid perforꢀance
degradation or loss of functionality.
Rev. 0 | Page 8 of 32
AD1939
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
1
2
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
AGND
MCLKI/XI
MCLKO/XO
AGND
AGND
FILTR
3
AGND
AVDD
4
5
AVDD
AGND
OR2N
6
OL3P
7
OL3N
OR2P
AD1939
TOP VIEW
(Not to Scale)
8
OR3P
OL2N
9
OR3N
OL2P
DIFFERENTIAL
OUTPUT
10
11
12
13
14
15
16
OL4P
OR1N
OL4N
OR1P
OR4P
OL1N
OR4N
OL1P
PD/RST
DSDATA4
DGND
CLATCH/ADR1
CCLK/SCL
DGND
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
NC = NO CONNECT
Figure 2. 64-Lead LQFP, Differential Output, Pin Configuration
Table 10. Pin Function Descriptions
Pin No.
In/Out
Mnemonic
Description
1
I
AGND
Analog Ground.
2
3
4
I
O
I
MCLKI/XI
MCLKO/XO
AGND
Master Clock Input/Crystal Oscillator Input.
Master Clock Output/Crystal Oscillator Output.
Analog Ground.
5
6
7
8
I
AVDD
OL3P
OL3N
OR3P
OR3N
OL4P
OL4N
OR4P
Analog Power Supply. Connect to analog 3.3 V supply.
DAC 3 Left Positive Output.
DAC 3 Left Negative Output.
DAC 3 Right Positive Output.
DAC 3 Right Negative Output.
DAC 4 Left Positive Output.
O
O
O
O
O
O
O
O
I
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
DAC 4 Left Negative Output.
DAC 4 Right Positive Output.
DAC 4 Right Negative Output
Power-Down Reset (Active Low).
OR4N
PD/RST
DSDATA4
DGND
I/O
I
I
I/O
I/O
I
I/O
I/O
I
DAC Input 4 (Input to DAC 4 L and R)/DAC TDM Data Out 2/AUX ADC 1 Data In.
Digital Ground.
DVDD
Digital Power Supply. Connect to digital 3.3 V supply.
DAC Input 3 (Input to DAC 3 L and R)/DAC TDM Data In 2/Aux DAC 2 Data Output.
DAC Input 2 (Input to DAC 2 L and R)/DAC TDM Data Out 1/AUX ADC 1 Data In.
DAC Input 1 (Input to DAC 1 L and R)/DAC TDM Data In 1/AUX ADC 2 Data In.
Bit Clock for DACs.
LR Clock for DACs.
+5 V Input to Regulator, Emitter of Pass Transistor.
+3.3 V Output of Regulator, Collector of Pass Transistor.
DSDATA3
DSDATA2
DSDATA1
DBCLK
DLRCLK
VSUPPLY
VSENSE
I
Rev. 0 | Page 9 of 32
AD1939
Pin No.
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
In/Out
Mnemonic
VDRIVE
ASDATA2
ASDATA1
ABCLK
ALRCLK
CIN/ADR0
COUT/SDA
DVDD
DGND
CCLK/SCL
CLATCH/ADR1
OL1P
OL1N
OR1P
OR1N
OL2P
OL2N
OR2P
OR2N
AGND
Description
O
I/O
O
I/O
I/O
I
I/O
I
I
Drive for Base of Pass Transistor.
ADC Serial Data Output 2 (ADC 2 L and R)/ADC TDM Data Input/Aux DAC 1 Data Output.
ADC Serial Data Output 1 (ADC 1 L and R)/ADC TDM Data Output.
Bit Clock for ADCs.
LR Clock for ADCs.
Control Data Input (SPI).
Control Data Output (SPI).
Digital Power Supply. Connect to digital 3.3 V supply.
Digital Ground.
Control Clock Input (SPI).
Latch Input for Control Data (SPI).
DAC 1 Left Positive Output.
DAC 1 Left Negative Output.
DAC 1 Right Positive Output.
DAC 1 Right Negative Output.
DAC 2 Left Positive Output.
DAC 2 Left Negative Output.
DAC 2 Right Positive Output.
DAC 2 Right Negative Output
Analog Ground.
Analog Power Supply. Connect to analog 3.3 V supply.
Analog Ground.
Voltage Reference Filter Capacitor Connection. Bypass with 10 μF||100 nF to AGND.
Analog Ground.
I
I
O
O
O
O
O
O
O
O
I
I
I
O
I
AVDD
AGND
FILTR
AGND
NC
NC
AVDD
CM
No Connect.
No Connect.
I
O
Analog Power Supply. Connect to analog 3.3 V supply.
Common-Mode Reference Filter Capacitor Connection. Bypass with
47 μF||100 nF to AGND.
53
54
55
56
57
58
59
60
61
62
63
64
I
I
I
I
I
I
I
I
ADC1LP
ADC1LN
ADC1RP
ADC1RN
ADC2LP
ADC2LN
ADC2RP
ADC2RN
LF
ADC1 Left Positive Input.
ADC1 Left Negative Input.
ADC1 Right Positive Input.
ADC1 Right Negative Input.
ADC2 Left Positive Input.
ADC2 Left Negative Input.
ADC2 Right Positive Input.
ADC2 Right Negative Input.
PLL Loop Filter, Return to AVDD.
Analog Power Supply. Connect to analog 3.3 V supply.
No Connect.
O
I
AVDD
NC
NC
No Connect.
Rev. 0 | Page 10 of 32
AD1939
TYPICAL PERFORMANCE CHARACTERISTICS
0.10
0.08
0.06
0.04
0.02
0
0
–50
–0.02
–0.04
–0.06
–0.08
–0.10
–100
–150
0
12
24
36
48
0
2
4
6
8
10
12
14
16
18
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 3. ADC Pass-Band Filter Response, 48 kHz
Figure 6. DAC Stop-Band Filter Response, 48 kHz
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
0.10
0.05
0
–0.05
–0.10
0
5
10
15
20
25
30
35
40
0
24
48
72
96
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 4. ADC Stop-Band Filter Response, 48 kHz
Figure 7. DAC Pass-Band Filter Response, 96 kHz
0.06
0.04
0.02
0
0
–50
–0.02
–0.04
–0.06
–100
–150
0
24
48
72
96
0
8
16
FREQUENCY (kHz)
24
FREQUENCY (kHz)
Figure 5. DAC Pass-Band Filter Response, 48 kHz
Figure 8. DAC Stop-Band Filter Response, 96 kHz
Rev. 0 | Page 11 of 32
AD1939
0.5
0.4
0
–2
0.3
0.2
0.1
–4
0
–0.1
–0.2
–0.3
–0.4
–6
–8
–10
48
–0.5
0
64
80
96
8
16
32
64
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 10. DAC Stop-Band Filter Response, 192 kHz
Figure 9. DAC Pass-Band Filter Response, 192 kHz
Rev. 0 | Page 12 of 32
AD1939
THEORY OF OPERATION
slew rate or low bandwidth can cause high frequency noise and
tones to fold down into the audio band; exercise care in
selecting these components.
ANALOG-TO-DIGITAL CONVERTERS (ADCS)
There are four analog-to-digital converter (ADC) channels in
the AD1939 configured as two stereo pairs with differential
inputs. The ADCs can operate at a nominal sample rate of 48 kHz,
96 kHz, or 192 kHz. The ADCs include on-board digital anti-
aliasing filters with 79 dB stop-band attenuation and linear
phase response, operating at an oversampling ratio of 128
(48 kHz, 96 kHz, and 192 kHz modes). Digital outputs are
supplied through two serial data output pins (one for each
stereo pair) and a common frame clock (ALRCLK) and bit
clock (ABCLK). Alternatively, one of the TDM modes can be
used to access up to 16 channels on a single TDM data line.
The voltage at CM, the common-mode reference pin, can be
used to bias the external op amps that buffer the output signals
(see the Power Supply and Voltage Reference section).
CLOCK SIGNALS
The on-chip phase locked loop (PLL) can be selected to
reference the input sample rate from either of the LRCLK pins
or 256, 384, 512, or 768 times the sample rate, referenced to the
48 kHz mode from the MCLKI/XI pin. The default at power-up
is 256 × fS from MCLKI/XI. In 96 kHz mode, the master clock
frequency stays at the same absolute frequency; therefore, the
actual multiplication rate is divided by 2. In 192 kHz mode,
the actual multiplication rate is divided by 4. For example, if a
device in the AD1939 family is programmed in 256 × fS mode, the
frequency of the master clock input is 256 × 48 kHz = 12.288 MHz.
If the AD1939 is then switched to 96 kHz operation (by writing
to the SPI or I2C® port), the frequency of the master clock
should remain at 12.288 MHz, which is 128 × fS in this example.
In 192 kHz mode, this becomes 64 × fS.
The ADCs must be driven from a differential signal source for
best performance. The input pins of the ADCs connect to internal
switched capacitors. To isolate the external driving op amp from
the glitches caused by the internal switched capacitors, each in-
put pin should be isolated by using a series-connected external
100 Ω resistor together with a 1 nF capacitor connected from
each input to ground. This capacitor must be of high quality, for
example, ceramic NPO or polypropylene film.
The differential inputs have a nominal common-mode voltage
of 1.5 V. The voltage at the common-mode reference pin (CM)
can be used to bias external op amps to buffer the input signals
(see the Power Supply and Voltage Reference section). The
inputs can also be ac-coupled and do not need an external dc
bias to CM.
The internal clock for the ADCs is 256 × fS for all clock modes.
The internal clock for the DACs varies by mode: 512 × fS (48 kHz
mode), 256 × fS (96 kHz mode), or 128 × fS (192 kHz mode). By
default, the on-board PLL generates this internal master clock
from an external clock. A direct 512 × fS (referenced to 48 kHz
mode) master clock can be used for either the ADCs or DACs if
selected in PLL and Clock Control 1 register.
A digital high-pass filter can be switched in line with the ADCs
under serial control to remove residual dc offsets. It has a 1.4 Hz,
6 dB per octave cutoff at a 48 kHz sample rate. The cutoff fre-
quency scales directly with sample frequency.
Note that it is not possible to use a direct clock for the ADCs set
to the 192 kHz mode. It is required that the on-chip PLL be
used in this mode.
DIGITAL-TO-ANALOG CONVERTERS (DACS)
The AD1939 digital-to-analog converter (DAC) channels are
arranged as differential, four stereo pairs giving eight analog
outputs for improved noise and distortion performance. The
DACs include on-board digital reconstruction filters with 70 dB
stop-band attenuation and linear phase response, operating at an
oversampling ratio of 4 (48 kHz or 96 kHz modes) or 2 (192 kHz
mode). Each channel has its own independently programmable
attenuator, adjustable in 255 steps in increments of 0.375 dB.
Digital inputs are supplied through four serial data input pins
(one for each stereo pair) and a common frame clock (DLRCLK)
and bit clock (DBCLK). Alternatively, one of the TDM modes can
be used to access up to 16 channels on a single TDM data line.
The PLL can be powered down in the PLL and Clock Control 0
register. To ensure reliable locking when changing PLL modes,
or if the reference clock is unstable at power-on, power down
the PLL and then power it back up when the reference clock has
stabilized.
The internal master clock (MCLK) can be disabled in the PLL
and Clock Control 0 register to reduce power dissipation when
the AD1939 is idle. The clock should be stable before it is
enabled. Unless a standalone mode is selected (see the Serial
Control Port section), the clock is disabled by reset and must be
enabled by writing to the SPI or I2C port for normal operation.
To maintain the highest performance possible, it is recommended
that the clock jitter of the internal master clock signal be limited
to less than 300 ps rms TIE (time interval error). Even at these
levels, extra noise or tones can appear in the DAC outputs if the
jitter spectrum contains large spectral peaks. If the internal PLL
is not being used, it is best to use an independent crystal oscillator
Each output pin has a nominal common-mode dc level of 1.5 V
and swings 1.27 V for a 0 dBFS digital input signal. A single op
amp, third-order, external, low-pass filter is recommended to
remove high frequency noise present on the output pins, as well
as to provide differential-to-single-ended conversion in the case
of the differential output. Note that the use of op amps with low
Rev. 0 | Page 13 of 32
AD1939
to generate the master clock. In addition, it is especially
important that the clock signal should not be passed through an
FPGA, CPLD, or other large digital chip (such as a DSP) before
being applied to the AD1939. In most cases, this induces clock
jitter due to the sharing of common power and ground
connections with other unrelated digital output signals. When
the PLL is used, jitter in the reference clock is attenuated above
a certain frequency depending on the loop filter.
SERIAL CONTROL PORT
The AD1939 has an SPI control port that permits programming
and reading back of the internal control registers for the ADCs,
DACs, and clock system. A standalone mode is also available for
operation without serial control; it is configured at reset using the
serial control pins. All registers are set to default, except the
internal MCLK enable is set to 1 and ADC BCLK and LRCLK
master/slave is set by the COUT/SDA pin. Standalone mode
only supports stereo mode with an I2S data format and 256 fS
MCLK rate. Refer to Table 11 for details. It is recommended to
RESET AND POWER-DOWN
Reset sets all the control registers to their default settings. To
avoid pops, reset does not power down the analog outputs.
After reset is deasserted and the PLL acquires lock condition,
an initialization routine runs inside the AD1939. This
initialization lasts for approximately 256 MCLKs.
CLATCH
use a weak pull-up resistor on
have a microcontroller. This pull-up resistor ensures that the
AD1939 recognizes the presence of a microcontroller.
in applications that
The SPI control port of the AD1939 is a 4-wire serial control
port. The format is similar to the Motorola SPI format except
the input data-word is 24 bits wide. The serial bit clock and
latch can be completely asynchronous to the sample rate of the
ADCs and DACs. Figure 11 shows the format of the SPI signal.
The first byte is a global address with a read/write bit. For the
AD1939 the address is 0x04, shifted left one bit due to the R/
bit. The second byte is the AD1939 register address and the
third byte is the data.
The power-down bits in the PLL and Clock Control 0, DAC
Control 1, and ADC Control 1 registers power down the
respective sections. All other register settings are retained. The
reset pin should be pulled low by an external resistor to
guarantee proper startup.
W
Table 11. Standalone Mode Selection
CLATCH/ADR1
ADC Clocks
Slave
Master
CIN/ADR0
COUT/SDA
CCLK/SCL
0
0
0
1
0
0
0
0
tCLS
tCLH
tCCH tCCL
tCCP
CLATCH
tCOTS
CCLK
tCDS tCDH
CIN
D23
D22
D9
D8
D8
D0
D0
tCOE
COUT
D9
tCOD
Figure 11. Format of SPI Signal
Rev. 0 | Page 14 of 32
AD1939
polarity of DBCLK and DLRCLK is programmable according to
the DAC Control 1 register. The ADC serial formats and serial
clock polarity are programmable according to the ADC Control 1
register. Both DAC and ADC serial ports are programmable to
become the bus masters according to DAC Control 1 register
and ADC Control 2 register. By default, both ADC and DAC
serial ports are in the slave mode.
POWER SUPPLY AND VOLTAGE REFERENCE
The AD1939 is designed for 3.3 V supplies. Separate power
supply pins are provided for the analog and digital sections.
To minimize noise pickup, these pins should be bypassed with
100 nF ceramic chip capacitors placed as close to the pins as
possible. A bulk aluminum electrolytic capacitor of at least
22 μF should also be provided on the same PC board as the
codec. For critical applications, improved performance is
obtained with separate supplies for the analog and digital sections.
If this is not possible, it is recommended that the analog and
digital supplies be isolated by means of a ferrite bead in series
with each supply. It is important that the analog supply be as
clean as possible.
TIME-DIVISION MULTIPLEXED (TDM) MODES
The AD1939 serial ports also have several different TDM serial
data modes. The first and most commonly used configurations
are shown in Figure 12 and Figure 13. In Figure 12, the ADC
serial port outputs one data stream consisting of four on-chip
ADCs followed by four unused slots. In Figure 13, the eight on-
chip DAC data slots are packed into one TDM stream. In this
mode, both DBCLK and ABCLK are 256 fS.
The AD1939 includes a 3.3 V regulator driver that only requires
an external pass transistor and bypass capacitors to make a 5 V
to 3.3 V regulator. If the regulator driver is not used, connect
VSUPPLY, VDRIVE, and VSENSE to DGND.
LRCLK
256 BCLKs
BCLK
32 BCLKs
All digital inputs are compatible with TTL and CMOS levels.
All outputs are driven from the 3.3 V DVDD supply and are
compatible with TTL and 3.3 V CMOS levels.
SLOT 1 SLOT 2 SLOT 3 SLOT 4
SLOT 5 SLOT 6 SLOT 7 SLOT 8
DATA
LEFT 1 RIGHT 1 LEFT 2 RIGHT 2
LRCLK
BCLK
The ADC and DAC internal voltage reference (VREF) is brought
out on FILTR and should be bypassed as close as possible to the
chip with a parallel combination of 10 μF and 100 nF. Any
external current drawn should be limited to less than 50 μA.
MSB
MSB–1
MSB–2
DATA
Figure 12. ADC TDM (8-Channel I2S Mode)
The internal reference can be disabled in the PLL and Clock
Control 1 register and FILTR can be driven from an external
source. This can be used to scale the DAC output to the clipping
level of a power amplifier based on its power supply voltage.
The ADC input gain varies by the inverse ratio. The total gain
from ADC input to DAC output remains constant.
LRCLK
BCLK
256 BCLKs
32 BCLKs
SLOT 1 SLOT 2 SLOT 3 SLOT 4 SLOT 5 SLOT 6 SLOT 7 SLOT 8
LEFT 1 RIGHT 1 LEFT 2 RIGHT 2 LEFT 3 RIGHT 3 LEFT 4 RIGHT 4
DATA
LRCLK
BCLK
The CM pin is the internal common-mode reference. It should
be bypassed as close as possible to the chip, with a parallel
combination of 47 μF and 100 nF. This voltage can be used to
bias external op amps to the common-mode voltage of the input
and output signal pins. The output current should be limited to
less than 0.5 mA source and 2 mA sink.
MSB
MSB–1
MSB–2
DATA
Figure 13. DAC TDM (8-Channel I2S Mode)
The I/O pins of the serial ports are defined according to the
serial mode that is selected. For a detailed description of the
function of each pin in TDM and AUX modes, see Table 12.
SERIAL DATA PORTS—DATA FORMAT
The AD1939 allows systems with more than eight DAC channels
to be easily configured by the use of an auxiliary serial data port.
The DAC TDM-AUX mode is shown in Figure 14. In this mode,
the AUX channels are the last four slots of the TDM data stream.
These slots are extracted and output to the AUX serial port. It
should be noted that due to the high DBCLK frequency, this mode
is available only in the 48 kHz/44.1 kHz/32 kHz sample rate.
The eight DAC channels use a common serial bit clock (DBCLK)
and a common left-right framing clock (DLRCLK) in the serial
data port. The four ADC channels use a common serial bit
clock (ABCLK) and left-right framing clock (ALRCLK) in the
serial data port. The clock signals are all synchronous with the
sample rate. The normal stereo serial modes are shown in
Figure 23.
The AD1939 also allows system configurations with more than
four ADC channels as shown in Figure 15 (using 8 ADCs) and
Figure 16 (using 16 ADCs). Again, due to the high ABCLK fre-
quency, this mode is available only in the 48 kHz/44.1 kHz/32 kHz
sample rate.
The ADC and DAC serial data modes default to I2S. The ports
can also be programmed for left-justified, right-justified, and
TDM modes. The word width is 24 bits by default and can be
programmed for 16 or 20 bits. The DAC serial formats are
programmable according to the DAC Control 0 register. The
Rev. 0 | Page 15 of 32
AD1939
Combining the AUX ADC and DAC modes results in a system
configuration of 8 ADCs and 12 DACs. The system, then, con-
sists of two external stereo ADCs, two external stereo DACs,
and one AD1939. This mode is shown in Figure 17 (combined
AUX DAC and ADC modes).
Table 12. Pin Function Changes in TDM and AUX Modes
Mnemonic
ASDATA1
ASDATA2
DSDATA1
DSDATA2
DSDATA3
DSDATA4
ALRCLK
Stereo Modes
ADC1 Data Out
ADC2 Data Out
DAC1 Data In
DAC2 Data In
DAC3 Data In
TDM Modes
AUX Modes
ADC TDM Data Out
ADC TDM Data In
DAC TDM Data In
DAC TDM Data Out
DAC TDM Data In 2 (Dual-Line Mode)
DAC TDM Data Out 2 (Dual-Line Mode)
ADC TDM Frame Sync In/Out
ADC TDM BCLK In/Out
DAC TDM Frame Sync In/Out
DAC TDM BCLK In/Out
TDM Data Out
AUX Data Out 1 (to Ext. DAC 1)
TDM Data In
AUX Data In 1 (from Ext. ADC 1)
AUX Data In 2 (from Ext. ADC 2)
AUX Data Out 2 (to Ext. DAC 2)
TDM Frame Sync In/Out
TDM BCLK In/Out
DAC4 Data In
ADC LRCLK In/Out
ADC BCLK In/Out
DAC LRCLK In/Out
DAC BCLK In/Out
ABCLK
DLRCLK
DBCLK
AUX LRCLK In/Out
AUX BCLK In/Out
ALRCLK
ABCLK
AUXILIARY DAC CHANNELS
WILL APPEAR AT
AUX DAC PORTS
UNUSED SLOTS
8-ON-CHIP DAC CHANNELS
DSDATA1
(TDM_IN)
EMPTY EMPTY EMPTY EMPTY DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 AUX L1 AUX R1 AUX L2 AUX R2
32 BITS
MSB
DLRCLK
(AUX PORT)
LEFT
RIGHT
DBCLK
(AUX PORT)
ASDATA2
MSB
MSB
MSB
(AUX1_OUT)
DSDATA4
(AUX2_OUT)
MSB
Figure 14. 16-Channel DAC TDM-AUX Mode
Rev. 0 | Page 16 of 32
AD1939
ALRCLK
ABCLK
8-ON-CHIP DAC CHANNELS
DSDATA1
(TDM_IN)
DAC L1
ADC L1
DAC R1
DAC L2
DAC R2
DAC L3
DAC R3
DAC L4
DAC R4
AUX R2
4-ON-CHIP ADC CHANNELS
ADC R1 ADC L2
4-AUX ADC CHANNELS
AUX R1 AUX L2
ASDATA1
(TDM_OUT)
ADC R2
AUX L1
32 BITS
MSB
DLRCLK
(AUX PORT)
LEFT
RIGHT
DBCLK
(AUX PORT)
DSDATA2
(AUX1_IN)
MSB
MSB
MSB
DSDATA3
(AUX2_IN)
MSB
Figure 15. 8-Channel AUX ADC Mode
ALRCLK
ABCLK
4-ON-CHIP ADC CHANNELS
AUXILIARY ADC CHANNELS
UNUSED SLOTS
ASDATA1
(TDM_OUT)
ADC L1 ADC R1 ADC L2 ADC R2 AUX L1 AUX R1 AUX L2 AUX R2 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED
32 BITS
MSB
DLRCLK
(AUX PORT)
LEFT
RIGHT
DBCLK
(AUX PORT)
DSDATA2
(AUX1_IN)
MSB
MSB
MSB
DSDATA3
(AUX2_IN)
MSB
Figure 16. 16-Channel AUX ADC Mode
Rev. 0 | Page 17 of 32
AD1939
ALRCLK
ABCLK
AUXILIARY DAC CHANNELS
WILL APPEAR AT
UNUSED SLOTS
8-ON-CHIP DAC CHANNELS
AUX DAC PORTS
DSDATA1
(TDM_IN)
EMPTY EMPTY EMPTY EMPTY DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 AUX L1 AUX R1 AUX L2 AUX R2
4-ON-CHIP ADC CHANNELS
AUXILIARY ADC CHANNELS
UNUSED SLOTS
ASDATA1
(TDM_OUT)
ADC L1 ADC R1 ADC L2 ADC R2 AUX L1 AUX R1 AUX L2 AUX R2 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED
DLRCLK
(AUX PORT)
LEFT
RIGHT
DBCLK
(AUX PORT)
DSDATA2
(AUX1_IN)
MSB
MSB
MSB
MSB
MSB
DSDATA3
(AUX2_IN)
MSB
MSB
MSB
ASDATA2
(AUX1_OUT)
DSDATA4
(AUX2_OUT)
Figure 17. Combined AUX DAC and ADC Mode
Rev. 0 | Page 18 of 32
AD1939
There are two configurations for the ADC port to work in
DAISY-CHAIN MODE
daisy-chain mode. The first one is with an ABCLK at 256 fS
shown in Figure 21. The second configuration is shown in
Figure 22. Note that in the 512 fS ABCLK mode, the ADC
channels occupy the first eight slots; the second eight slots are
empty. The TDM_IN of the first AD1939 must be grounded in
all modes of operation.
The AD1939 also allows a daisy-chain configuration to expand
the system to 8 ADCs and 16 DACs (see Figure 18). In this
mode, the DBCLK frequency is 512 fS. The first eight slots of the
DAC TDM data stream belong to the first AD1939 in the chain
and the last eight slots belong to the second AD1939. The second
AD1939 is the device attached to the DSP TDM port.
The I/O pins of the serial ports are defined according to the
serial mode selected. See Table 13 for a detailed description of
the function of each pin. See Figure 26 for a typical AD1939
configuration with two external stereo DACs and two external
stereo ADCs.
To accommodate 16 channels at a 96 kHz sample rate, the
AD1939 can be configured into a dual-line, TDM mode as
shown in Figure 19. This mode allows a slower DBCLK than
normally required by the one-line TDM mode.
Again, the first four channels of each TDM input belong to the
first AD1939 in the chain and the last four channels belong to
the second AD1939.
Figure 23 through Figure 25 show the serial mode formats. For
maximum flexibility, the polarity of LRCLK and BCLK are
programmable. In these figures, all of the clocks are shown with
their normal polarity. The default mode is I2S.
The dual-line TDM mode can also be used to send data at a
192 kHz sample rate into the AD1939 as shown in Figure 20.
DLRCLK
DBCLK
8 DAC CHANNELS OF THE FIRST IC IN THE CHAIN
DSDATA1 (TDM_IN)
8 DAC CHANNELS OF THE SECOND IC IN THE CHAIN
DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4
OF THE SECOND AD1939
DSDATA2 (TDM_OUT)
OF THE SECOND AD1939
THIS IS THE TDM
DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4
TO THE FIRST AD1939
8 UNUSED SLOTS
32 BITS
FIRST
AD1939
SECOND
AD1939
DSP
MSB
Figure 18. Single-Line DAC TDM Daisy-Chain Mode (Applicable to 48 kHz Sample Rate, 16-Channel, Two-AD1939 Daisy Chain)
Rev. 0 | Page 19 of 32
AD1939
DLRCLK
DBCLK
8 DAC CHANNELS OF THE FIRST IC IN THE CHAIN
8 DAC CHANNELS OF THE SECOND IC IN THE CHAIN
DSDATA1
(IN)
DAC L1
DAC R1
DAC L2
DAC R2
DAC L1
DAC L1
DAC L3
DAC L3
DAC R1
DAC R1
DAC R3
DAC R3
DAC L2
DAC L2
DAC L4
DAC L4
DAC R2
DAC R2
DAC R4
DAC R4
DSDATA2
(OUT)
DSDATA3
(IN)
DAC L3
DAC R3
DAC L4
DAC R4
DSDATA4
(OUT)
32 BITS
MSB
FIRST
AD1939
SECOND
AD1939
DSP
Figure 19. Dual-Line DAC TDM Mode (Applicable to 96 kHz Sample Rate, 16-Channel, Two-AD1939 Daisy Chain); DSDATA3 and DSDATA4 Are the Daisy Chain
DLRCLK
DBCLK
DSDATA1
DSDATA2
DAC L1
DAC L3
DAC R1
DAC R3
DAC L2
DAC L4
DAC R2
DAC R4
32 BITS
MSB
Figure 20. Dual-Line DAC TDM Mode (Applicable to 192 kHz Sample Rate, 8-Channel Mode)
ALRCLK
ABCLK
4 ADC CHANNELS OF SECOND IC IN THE CHAIN
4 ADC CHANNELS OF FIRST IC IN THE CHAIN
ADC L1 ADC R1 ADC L2 ADC R2
ASDATA1 (TDM_OUT
OF THE SECOND AD1939
IN THE CHAIN)
ADC L1
ADC R1
ADC L2
ADC R2
ASDATA2 (TDM_IN
OF THE SECOND AD1939
IN THE CHAIN)
ADC L1
ADC R1
ADC L2
ADC R2
32 BITS
FIRST
AD1939
SECOND
AD1939
DSP
MSB
Figure 21. ADC TDM Daisy-Chain Mode (256 fS ABCLK, Two-AD1939 Daisy Chain)
Rev. 0 | Page 20 of 32
AD1939
ALRCLK
ABCLK
4 ADC CHANNELS OF
SECOND IC IN THE CHAIN
4 ADC CHANNELS OF
FIRST IC IN THE CHAIN
ASDATA1 (TDM_OUT
OF THE SECOND AD1939
IN THE CHAIN)
ADC L1 ADC R1 ADC L2 ADC R2 ADC L1 ADC R1 ADC L2 ADC R2
ASDATA2 (TDM_IN
OF THE SECOND AD1939
IN THE CHAIN)
ADC L1 ADC R1 ADC L2 ADC R2
32 BITS
FIRST
AD1939
SECOND
DSP
AD1939
MSB
Figure 22. ADC TDM Daisy-Chain Mode (512 fS ABCLK, Two-AD1939 Daisy Chain)
LEFT CHANNEL
RIGHT CHANNEL
LRCLK
BCLK
SDATA
MSB
LSB
MSB
LSB
LEFT-JUSTIFIED MODE—16 BITS TO 24 BITS PER CHANNEL
LEFT CHANNEL
LRCLK
RIGHT CHANNEL
BCLK
MSB
I S MODE—16 BITS TO 24 BITS PER CHANNEL
LSB
SDATA
MSB
LSB
2
LEFT CHANNEL
RIGHT CHANNEL
LRCLK
BCLK
SDATA
MSB
LSB
MSB
LSB
RIGHT-JUSTIFIED MODE—SELECT NUMBER OF BITS PER CHANNEL
LRCLK
BCLK
SDATA
MSB
LSB
MSB
LSB
DSP MODE—16 BITS TO 24 BITS PER CHANNEL
1/fS
NOTES
1. DSP MODE DOES NOT IDENTIFY CHANNEL.
2. LRCLK NORMALLY OPERATES AT fS EXCEPT FOR DSP MODE, WHICH IS 2 ×fS.
3. BCLK FREQUENCY IS NORMALLY 64 × LRCLK BUT MAY BE OPERATED IN BURST MODE.
Figure 23. Stereo Serial Modes
Rev. 0 | Page 21 of 32
AD1939
tDBH
DBCLK
tDBL
tDLS
tDLH
DLRCLK
tDDS
DSDATA
LEFT-JUSTIFIED
MODE
MSB
MSB–1
tDDH
tDDS
MSB
DSDATA
I S-JUSTIFIED
2
MODE
tDDH
tDDS
MSB
tDDS
LSB
tDDH
DSDATA
RIGHT-JUSTIFIED
MODE
tDDH
Figure 24. DAC Serial Timing
tABH
ABCLK
tABL
tALS
tALH
ALRCLK
tABDD
ASDATA
LEFT-JUSTIFIED
MODE
MSB
MSB–1
MSB
tABDD
ASDATA
I S-JUSTIFIED
2
MODE
tABDD
ASDATA
RIGHT-JUSTIFIED
MODE
MSB
LSB
Figure 25. ADC Serial Timing
Rev. 0 | Page 22 of 32
AD1939
Table 13. Pin Function Changes in TDM and AUX Modes (Replication of Table 12)
Mnemonic
ASDATA1
ASDATA2
DSDATA1
DSDATA2
DSDATA3
DSDATA4
ALRCLK
Stereo Modes
ADC1 Data Out
ADC2 Data Out
DAC1 Data In
DAC2 Data In
DAC3 Data In
TDM Modes
AUX Modes
ADC TDM Data Out
ADC TDM Data In
DAC TDM Data In
DAC TDM Data Out
DAC TDM Data In 2 (Dual-Line Mode)
DAC TDM Data Out 2 (Dual-Line Mode)
ADC TDM Frame Sync In/Out
ADC TDM BCLK In/Out
DAC TDM Frame Sync In/Out
DAC TDM BCLK In/Out
TDM Data Out
AUX Data Out 1 (to Ext. DAC 1)
TDM Data In
AUX Data In 1 (from Ext. ADC 1)
AUX Data In 2 (from Ext. ADC 2)
AUX Data Out 2 (to Ext. DAC 2)
TDM Frame Sync In/Out
TDM BCLK In/Out
DAC4 Data In
ADC LRCLK In/Out
ADC BCLK In/Out
DAC LRCLK In/Out
DAC BCLK In/Out
ABCLK
DLRCLK
DBCLK
AUX LRCLK In/Out
AUX BCLK In/Out
SHARC IS RUNNING IN SLAVE MODE
(INTERRUPT-DRIVEN)
30MHz
SHARC
12.288MHz
LRCLK
BCLK
LRCLK
BCLK
AUX
ADC 1
AUX
DAC 1
DATA
MCLK
DATA
MCLK
ASDATA1 ALRCLK ABCLK DSDATA1
DBCLK
DLRCLK
AD1939
LRCLK
BCLK
LRCLK
BCLK
ASDATA2
DSDATA4
DSDATA2
DSDATA3
MCLK
TDM MASTER
AUX MASTER
AUX
ADC 2
AUX
DATA DAC 2
DATA
MCLK
MCLK
Figure 26. Example of AUX Mode Connection to SHARC (AD1939 as TDM Master/AUX Master Shown)
Rev. 0 | Page 23 of 32
AD1939
CONTROL REGISTERS
DEFINITIONS
2
W
The format is the same for I C and SPI ports. The global address for the AD1939 is 0x04, shifted left one bit due to the R/ bit. However,
in I2C, ADR0 and ADR1 are OR’ed into Bit 17 and Bit 8 to provide multiple chip addressing. All registers are reset to 0, except for the
DAC volume registers that are set to full volume.
Note that the first setting in each control register parameter is the default setting.
Table 14. Register Format
Global Address
R/W
Register Address
Data
23:17
16
15:8
7:0
Bit
Table 15. Register Addresses and Functions
Address
Function
0
1
2
PLL and Clock Control 0
PLL and Clock Control 1
DAC Control 0
3
DAC Control 1
4
DAC Control 2
5
6
7
8
DAC individual channel mutes
DAC 1L volume control
DAC 1R volume control
DAC 2L volume control
DAC 2R volume control
DAC 3L volume control
DAC 3R volume control
DAC 4L volume control
DAC 4R volume control
ADC Control 0
9
10
11
12
13
14
15
16
ADC Control 1
ADC Control 2
PLL AND CLOCK CONTROL REGISTERS
Table 16. PLL and Clock Control 0 Register
Bit
Value
Function
Description
0
0
1
Normal operation
Power-down
PLL power-down
2:1
4:3
6:5
7
00
01
10
11
00
01
10
11
00
01
10
11
0
INPUT 256 (×44.1 kHz or 48 kHz)
INPUT 384 (×44.1 kHz or 48 kHz)
INPUT 512 (×44.1 kHz or 48 kHz)
INPUT 768 (×44.1 kHz or 48 kHz)
XTAL oscillator enabled
256 × fS VCO output
512 × fS VCO output
Off
MCLKI/XI
MCLKO/XO pin
PLL input
MCLKI
DLRCLK
ALRCLK
Reserved
Disable: ADC and DAC idle
Enable: ADC and DAC active
Internal master clock enable
1
Rev. 0 | Page 24 of 32
AD1939
Table 17. PLL and Clock Control 1 Register
Bit
Value
Function
PLL clock
MCLK
Description
0
0
1
DAC clock source select
1
0
1
PLL clock
MCLK
ADC clock source select
2
0
1
Enabled
Disabled
Not locked
Locked
On-chip voltage reference
PLL lock indicator (read only)
3
0
1
7:4
0000
Reserved
DAC CONTROL REGISTERS
Table 18. DAC Control 0 Register
Bit
Value
Function
Description
0
0
Normal
Power-down
1
Power-down
2:1
5:3
00
01
10
11
32 kHz/44.1 kHz/48 kHz
64 kHz/88.2 kHz/96 kHz
128 kHz/176.4 kHz/192 kHz
Reserved
Sample rate
000
001
010
011
100
101
110
111
00
1
0
8
12
16
Reserved
Reserved
Reserved
SDATA delay (BCLK periods)
7:6
Stereo (normal)
Serial format
01
10
11
TDM (daisy chain)
DAC AUX mode (ADC-, DAC-, TDM-coupled)
Dual-line TDM
Table 19. DAC Control 1 Register
Bit
Value
Function
Description
0
0
1
Latch in mid cycle (normal)
Latch in at end of cycle (pipeline)
64 (2 channels)
128 (4 channels)
256 (8 channels)
512 (16 channels)
Left low
BCLK active edge (TDM in)
2:1
00
01
10
11
0
BCLKs per frame
3
4
5
6
7
LRCLK polarity
LRCLK master/slave
BCLK master/slave
BCLK source
1
Left high
0
1
Slave
Master
0
1
Slave
Master
0
1
DBCLK pin
Internally generated
Normal
0
BCLK polarity
1
Inverted
Rev. 0 | Page 25 of 32
AD1939
Table 20. DAC Control 2 Register
Bit
Value
Function
Unmute
Mute
Description
0
0
1
Master mute
2:1
4:3
00
01
10
11
00
01
10
11
0
Flat
De-emphasis (32 kHz/44.1 kHz/48 kHz mode only)
48 kHz curve
44.1 kHz curve
32 kHz curve
24
20
Reserved
16
Word width
5
Noninverted
Inverted
Reserved
DAC output polarity
1
7:6
00
Table 21. DAC Individual Channel Mutes
Bit
Value
Function
Unmute
Mute
Description
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
DAC 1 left mute
1
2
3
4
5
6
7
Unmute
Mute
DAC 1 right mute
DAC 2 left mute
DAC 2 right mute
DAC 3 left mute
DAC 3 right mute
DAC 4 left mute
DAC 4 right mute
Unmute
Mute
Unmute
Mute
Unmute
Mute
Unmute
Mute
Unmute
Mute
Unmute
Mute
Table 22. DAC Volume Controls
Bit
Value
Function
Description
7:0
0
No attenuation
DAC volume control
1 to 254 −3/8 dB per step
255 Full attenuation
Rev. 0 | Page 26 of 32
AD1939
ADC CONTROL REGISTERS
Table 23. ADC Control 0 Register
Bit
Value
Function
Description
0
0
Normal
Power-down
1
Power down
1
0
1
Off
On
High-pass filter
ADC 1L mute
2
0
Unmute
1
Mute
3
0
1
Unmute
Mute
ADC 1R mute
ADC 2L mute
4
0
Unmute
1
Mute
5
0
1
Unmute
Mute
ADC 2R mute
Output sample rate
7:6
00
01
10
11
32 kHz/44.1 kHz/48 kHz
64 kHz/88.2 kHz/96 kHz
128 kHz/176.4 kHz/192 kHz
Reserved
Table 24. ADC Control 1 Register
Bit
Value
Function
Description
1:0
00
24
Word width
01
20
10
Reserved
11
16
4:2
000
001
010
011
100
101
110
111
00
1
0
8
12
16
Reserved
Reserved
Reserved
SDATA delay (BCLK periods)
6:5
7
Stereo
Serial format
01
10
11
TDM (daisy chain)
ADC Aux mode (ADC-, DAC, TDM-coupled)
Reserved
0
1
Latch in mid cycle (normal)
Latch in at end of cycle (pipeline)
BCLK active edge (TDM in)
Rev. 0 | Page 27 of 32
AD1939
Table 25. ADC Control 2 Register
Bit
Value
Function
Description
0
0
50/50 (allows 32-/24-/20-/16-BCLK/channel)
LRCLK format
1
Pulse (32-BCLK/channel)
1
0
Drive out on falling edge (DEF)
BCLK polarity
1
Drive out on rising edge
2
0
1
Left low
Left high
Slave
Master
64
128
256
512
LRCLK polarity
LRCLK master/slave
BCLKs per frame
3
0
1
5:4
00
01
10
11
0
6
7
Slave
BCLK master/slave
BCLK source
1
Master
ABCLK pin
Internally generated
0
1
Rev. 0 | Page 28 of 32
AD1939
To relax the requirement for the setup time of the AD1939 in
ADDITIONAL MODES
cases of high speed TDM data transmission, the AD1939 can
latch in the data using the falling edge of DBCLK. This effec-
tively dedicates the entire BCLK period to the setup time. This
mode is useful in cases where the source has a large delay time
in the serial data driver. Figure 28 shows this pipeline mode of
data transmission.
The AD1939 offers several additional modes for board level
design enhancements. To reduce the EMI in board level design,
serial data can be transmitted without an explicit BCLK. See
Figure 27 for an example of a DAC TDM data transmission
mode that does not require high speed DBCLK. This configura-
tion is applicable when the AD1939 master clock is generated
by the PLL with the DLRCLK as the PLL reference frequency.
Both the BCLK-less and pipeline modes are available on the
ADC serial data port.
DLRCLK
32 BITS
INTERNAL
DBCLK
DSDATA
DLRCLK
INTERNAL
DBCLK
TDM-DSDATA
Figure 27. Serial DAC Data Transmission in TDM Format Without DBCLK
(Applicable Only If PLL Locks to DLRCLK, This Model Is Also Available in the ADC Serial Data Port)
DLRCLK
DBCLK
DATA MUST BE VALID
AT THIS BCLK EDGE
MSB
DSDATA
Figure 28. I2S Pipeline Mode in DAC Serial Data Transmission
(Applicable in Stereo and TDM, Useful for High Frequency TDM Transmission,
This Model Is Also Available in the ADC Serial Data Port)
Rev. 0 | Page 29 of 32
AD1939
APPLICATION CIRCUITS
Typical application circuits are shown in Figure 29 through Figure 32. Figure 29 shows a typical ADC input filter circuit. Recommended
loop filters for LR clock and master clock as the PLL reference are shown in Figure 30. Output filters for the DAC outputs are shown in
Figure 31 and a regulator circuit is shown in Figure 32.
120pF
600Z
AUDIO
INPUT
68pF
NPO
2
3
–
100pF
1
OP275
+
DAC
OUTN
2
–
270pF
NPO
1
AUDIO
OUTPUT
OP275
3
560pF
NPO
4.7µF
+
+
2.2nF
NPO
ADCxN
DAC
OUTP
1nF
NPO
120pF
150pF
NPO
100pF
1nF
NPO
6
5
–
4.7µF
+
7
OP275
+
ADCxP
Figure 31. Typical DAC Output Filter Circuit (Differential)
Figure 29. Typical ADC Input Filter Circuit
100nF
10µF
E
+
LRCLK
39nF
MCLK
5.6nF
VSUPPLY
5V
LF
LF
B
+
VDRIVE
VSENSE
FZT953
2.2nF
390nF
C
3.3V
AVDD2
AVDD2
+
100nF
10µF
Figure 30. Recommended Loop Filters for LRCLK or MCLK PLL Reference
Figure 32. Recommended 3.3 V Regulator Circuit
Rev. 0 | Page 30 of 32
AD1939
OUTLINE DIMENSIONS
0.75
0.60
0.45
12.00
BSC SQ
1.60
MAX
64
49
1
48
PIN 1
10.00
BSC SQ
TOP VIEW
(PINS DOWN)
1.45
1.40
1.35
0.20
0.09
7°
3.5°
0°
0.08 MAX
COPLANARITY
16
33
0.15
0.05
SEATING
PLANE
17
32
VIEW A
0.27
0.22
0.17
0.50
BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BCD
Figure 33. 64-Lead Low Profile Quad Flat Package [LQFP]
(ST-64-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
–40°C to +105°C
–40°C to +105°C
Package Description
64-Lead LQFP
64-Lead LQFP, 13”Reel
Evaluation Board
Package Option
ST-64-2
ST-64-2
AD1939YSTZ1, 2
AD1939YSTZRL
EVAL-AD1939EB
1 Z = Pb-free part.
2 Differential output, SPI control port.
Rev. 0 | Page 31 of 32
AD1939
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06071-0-7/06(0)
Rev. 0 | Page 32 of 32
相关型号:
©2020 ICPDF网 联系我们和版权申明