JPS250PQ48 [XPPOWER]
AC-DC Power Supplies; AC- DC电源型号: | JPS250PQ48 |
厂家: | XP POWER LIMITED |
描述: | AC-DC Power Supplies |
文件: | 总4页 (文件大小:490K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
250 Watts
xppower.com
JPS250 Series
•
•
•
•
•
•
•
200 W with Convection Cooling
High Efficiency - up to 88%
Meets 1U, Low Profile Requirements
AC OK & DC OK Signals
Zero Voltage Switching Technology
Remote On/Off & Remote Sense
Current Share
Specification
Input
General
Input Voltage
Input Frequency
Input Current
Inrush Current
Power Factor
• 90-264 VAC (170-370 VDC)
Efficiency
Isolation
• Up tꢁ 88ꢀ
• 47-63 Hz
• 3000 VAC Input tꢁ Output
1500 VAC Input tꢁ Grꢁund
500 VAC Output tꢁ Grꢁund
• 2.75 A/1.40 A max at 115 VAC/230 VAC
• 30 A at 115 VAC, 60 A at 230 VAC
• 0.99 typical
Switching Frequency
Power Density
Signals
• 120 kHz typical fꢁr PFC and PWM
• 4.96 W/In3
Earth Leakage Current • 2.0 mA max 264 VAC/60 Hz
• AC OK, DC OK, Remꢁte On/Off
(see cꢁntrꢁl and supervisꢁry signals)
Input Protection
• Internal 5 A, 250 V fuse
MTBF
• 255 kHrs per MIL-HDBK-217F at +25 °C
Output
Output Voltage
• See tables
Environmental
Output Voltage Trim
Initial Set Accuracy
•
10ꢀ ꢁn ꢁutput 1 ꢁnly
Operating Temperature • 0 °C tꢁ +70 °C, (see derating curve)
• At 60ꢀ rated lꢁad 1ꢀ ꢁn V1 ꢂ V2,
5ꢀ ꢁn V3 ꢂ V4
Full pꢁwer tꢁ +50 °C
Cooling
• 250 W with 18 CFM airflꢁw
200 W cꢁnvectiꢁn cꢁꢁling
Minimum Load
• Single ꢁutput mꢁdels: Nꢁ minimum lꢁad
required. Multi-ꢁutput mꢁdels, see nꢁte 4
Operating Humidity
Storage Temperature
Operating Altitude
Vibration
• 5-95ꢀ RH, nꢁn-cꢁndensing
• -20 °C tꢁ +85 °C
• 3000 m
Start Up Delay
Start Up Rise Time
Hold Up Time
• 2 s typical
• 80 ms typical
• 20 ms min at lꢁw line ꢂ rated lꢁad
• 2 g, 10 Hz tꢁ 55 Hz,
3 mins/cycle fꢁr 30 mins each axis
Line Regulation
•
0.5ꢀ at rated lꢁad acrꢁss input
vꢁltage range
Load Regulation
Transient Response
Ripple & Noise
•
1ꢀ fꢁr single ꢁutput mꢁdels ꢂ V1 ꢂ V2
ꢁf multi-ꢁutput mꢁdels, 5ꢀ fꢁr V3 ꢂ V4
EMC & Safety
Emissions
• EN55022, level B cꢁnducted
FCC 20780, level B cꢁnducted
• 4ꢀ max deviatiꢁn, recꢁvery tꢁ within
1ꢀ in 500 µs fꢁr a 25ꢀ lꢁad change
Harmonic Currents
Voltage Flicker
ESD Immunity
Radiated Immunity
EFT/Burst
• EN61000-3-2
•
1ꢀ max pk-pk, 20 MHz BW
• EN61000-3-3
Overvoltage Protection • 115-140ꢀ ꢁn single ꢁutputs ꢂ V1 ꢁf quad
• EN61000-4-2, level 3 Perf Criteria A
• EN61000-4-3, 10 V/m Perf Criteria A
• EN61000-4-4, level 3 Perf Criteria A
• EN61000-4-5, level 3 Perf Criteria A
ꢁutput mꢁdels, recycle input tꢁ reset
Overtemperature
Protection
• Shuts dꢁwn at +110 °C, autꢁ recꢁvery
measured internally
Surge
Overload Protection
• 110-130ꢀ ꢁf max rated lꢁad ꢁn all O/Ps,
trip ꢂ restart (Hiccup mꢁde), autꢁ recꢁvery
Safety Approvals
• EN60950-1:2001, UL60950-1,
CSA C22.2 Nꢁ. 60950-1-03,
CE Mark LVD
Short Circuit Protection • Trip and restart (Hiccup mꢁde)
Temperature
Coefficient
•
0.05ꢀ/°C
Remote Sense
• Cꢁmpensates fꢁr up tꢁ 0.5 V drꢁp
Remote On/Off
Current Share
• On = Lꢁgic Lꢁw ꢁr Open, Off = Lꢁgic High
• Single wire current sharing ꢁn single
ꢁutput mꢁdels ꢂ V1 ꢂ V2 ꢁf multi-ꢁutput
mꢁdels (4 supplies can be paralleled)
Fan Output
• 5 V mꢁdel: 5 V at 390 mA,
24 V mꢁdel: 24 V at 80 mA,
all ꢁther mꢁdels: 12 V at 112 mA
JPS250 - Single Output
Models and Ratings
Output Current
Convection-cooled
Output
Power(1)
225 W
Output
Voltage
5 V
Ripple & Noise
Model
Efficiency
Pk-Pk
Number(2)
18 CFM
45.0 A
21.0 A
17.0 A
10.4 A
5.2 A
36.0 A
17.0 A
13.5 A
8.5 A
50 mV
83ꢀ
86ꢀ
87ꢀ
88ꢀ
88ꢀ
JPS250PS05C†^
12 V
15 V
24 V
48 V
120 mV
120 mV
200 mV
200 mV
JPS250PS12C†^
JPS250PS15C†^
JPS250PS24C†^
JPS250PS48C†^
250 W
4.3 A
Notes
1. Maximum power with 18 CFM forced air is 250 W, or 200 W with convection cooling.
2. For non-current share version delete suffix ‘C’ from model number.
† Available frꢁm Farnell. See pages 204-206.
^ Available frꢁm Newark. See pages 207-208.
Mechanical Details
All dimensiꢁns are in inches (mm) Tolerance: 0.03 (0.8) max Weight: 1.65 lbs (750 g) apprꢁx.
All models (except JPS250PS05)
8.00 (203.2)
PIN CONNECTIONS
TB2
JPS250PS05 All other models
A
B
A
B
10
TB4
All models
Signal 0 V
DC OK
L
TB4
2
Pin
N
E
1
+
TB3
-
1
2
+5 V
+5 V
0 V
+V
TB1
1
3.75
4.20
+V
(95.3)
(106.7)
3
+V
AC OK
TB2
A
TRANSFORMER
4
0 V
0 V
0 V
0 V
Remꢁte On/Off
+Sense
6
5
0 V
A
B
B
6
0 V
-Sense
7
+5 V
+5 V
Current Share(6)
5.50 (139.0)
6.50 (165.1)
8
N/C
9
N/C
0.30
(7.6)
7.40 (188.0)
10
N/C
A
B
A
B
1.51
(38.3)
Notes:
0.75
(19.1)
1. TB3 is fꢁr fan, with Mꢁlex 5045-02A ꢁr equivalent.
2. TB1 (AC input) and TB2 (DC ꢁutput) are terminal blꢁcks.
3. TB4 signal cꢁnnectꢁr is Mꢁlex 70246-10 ꢁr equivalent.
4. Maximum mꢁunting screw penetratiꢁn is 0.16 (4.0) frꢁm chassis
ꢁuter surface.
5. Fan/Cꢁver ꢁptiꢁn available, ꢁrder part number:
5 V mꢁdels: JPS250 F/CVR 5 ^
12, 15 ꢂ 48 V mꢁdels: JPS250 F/CVR ^
24 V mꢁdels: JPS250 F/CVR 24 ^
0.36
(9.1)
JPS250PS05
8.00 (203.2)
†
†
2
10
A
B
†
TB4
L
1
Or add suffix ‘-E’ tꢁ mꢁdel number tꢁ receive unit with cꢁver fitted.
6. Fꢁr current share ꢁperatiꢁn cꢁnnect signal 0 V (pin 1) between
units and current share (pin 7) between units. Fꢁr nꢁn ‘C’ mꢁdels
pin 7 (single wire parallel) is nꢁt used.
N
E
1
TB1
3.75
(95.3)
4.20
(106.7)
TB2
Fixing Holes:
TRANSFORMER
A = #6-32 screw mꢁunting hꢁles
B = M3 x 0.5 screw mꢁunting hꢁles
+
-
TB3
8
A
A
B
B
1.30 (32.1)
0.70 (19.1)
5.50 (139.0)
6.50 (165.1)
Application Notes
Derating Curve
Signals
100
1. Tꢁ turn ꢁff the ꢁutput, apply 5 V tꢁ the remꢁte On/Off.
2. AC OK is a TTL signal which gꢁes LOW when input falls belꢁw
60 VAC at rated lꢁad.
3. DC OK is a TTL signal which gꢁes LOW when PSU is in an
ꢁvercurrent cꢁnditiꢁn, ꢁvervꢁltage cꢁnditiꢁn, disabled ꢁr when
ꢁutput falls ꢁut ꢁf regulatiꢁn.
JPS250PS with 18 CFM Fan
JPS250PS Convection-cooled
90
80
70
60
50
40
30
20
10
L
O
A
D
%)
4. Fꢁr AC OK and DC OK signals, sꢁurce current is 1 mA, sink
current is 6 mA.
0
0
10
20
30
40
80
50
60
70
Ambient Temperature (˚C)
JPS250 - Multi Output
Models and Ratings
Output 1
Output 2
Conv.
Cooled 18 CFM
Output 3
Conv.
Output 4
Model
Output
V1
Conv.
Cooled 18 CFM
Max
Output
V2
Max
Output
V3
Max
Output
V4
Conv.
Cooled 18 CFM
Max
Number(2,3)
Cooled 18 CFM
†
JPS250PQ46 ^
3.3 V
5.0 V
5.0 V
5.0 V
16.0 A
17.5 A
20.0 A
20.0 A
20 A
30 A
25 A
25 A
5 V
12 V
12 V
15 V
12 A
7 A
4 A
3 A
20 A
8 A
6 A
5 A
12 V
-12 V
24 V
24 V
5 A
2 A
2 A
2 A
6 A
3 A
3 A
3 A
-12 V
-5 V
-12 V
-15 V
1 A
1 A
1 A
1 A
2 A
2 A
2 A
2 A
†
JPS250PQ41 ^
†
JPS250PQ47 ^
†
JPS250PQ48 ^
Notes
1. Maximum power with 18 CFM forced air is 250 W, or 200 W with convection cooling.
2. For current share option add suffix ‘C’ to model number.
3. Current share models are built to order.
4. All models require 2 A minimum load on V1. On V2, JPS250PQ46 requires 1 A and JPS250PQ41 requires 0.5 A.
† Available frꢁm Farnell. See pages 204-206.
^ Available frꢁm Newark. See pages 207-208.
Mechanical Details
All dimensiꢁns are in inches (mm). Tolerance: 0.03 (0.8) max. Weight: 1.65 lbs (750 g) apprꢁx.
PIN CONNECTIONS - TB2
8.00 (203.2)
Pin
1
PQ41
+5 V +S
+5 V PS(6)
+12 V +S
DC OK
PQ46
+3.3 V +S
+5 V -S
PQ47
+5 V +S
+5 V PS(6)
+12 V +S
DC OK
PQ48
+5 V +S
+5 V PS(6)
+15 V +S
DC OK
1
L
2
N
E
3
+3.3 V PS(6)
TB3
TRANSFORMER
TB2
4
DC OK
TB1
2
1
10
4.20
(106.7)
5
+12 V -S
+5 V +S
+12 V -S
+15 V -S
8
6
+5 V -S
+12 V PS(6)
+3.3 V -S
+5 V PS(6)
+5 V -S
+12 V PS(6)
+5 V -S
+15 V PS(6)
7
8
Remꢁte On/Off Remꢁte On/Off Remꢁte On/Off Remꢁte On/Off
TB5
+
-
9
AC OK
0 V
AC OK
0 V
AC OK
0 V
AC OK
0 V
10
0.30
(7.6)
0.16 (4.0)
7.40 (187.9)
PIN CONNECTIONS - TB3
A
B
A
B
1.30 1.50
(33.1) (38.1)
Pin
1
PQ41
+5 V
+5 V
0 V
PQ46
+12 V
-12 V
+5 V
+5 V
0 V
PQ47
+5 V
+5 V
0 V
PQ48
+5 V
+5 V
0 V
0.75
(19.1)
2
0.36
(9.1)
3
4
0 V
0 V
0 V
8.00 (203.2)
5
0 V
0 V
0 V
A
B
B
A
6
-5 V
-12 V
+12 V
0 V
-12 V
+24 V
+12 V
-15 V
+24 V
+15 V
7
0 V
8
0 V
9
+3.3 V
+3.3 V
3.75
(95.3)
10
1.30 (32.1)
0.70
Notes:
1. TB5 is fꢁr fan with Mꢁlex 5045-02A ꢁr equivalent.
2. TB1 (AC input) and TB3 (DC ꢁutput) are terminal blꢁcks.
3. TB2 signal cꢁnnectꢁr is Mꢁlex 70246-10 ꢁr equivalent.
4. Maximum mꢁunting screw penetratiꢁn is 0.16 (4.0) frꢁm chassis
ꢁuter surface.
(19.1)
A
B
B
A
5.50 (139.0)
6.50 (165.1)
0.22
(5.7)
5. Fan/Cꢁver ꢁptiꢁn available, ꢁrder part number:
PQ41, PQ46 ꢂ PQ47: JPS250 F/CVR PQ48: JPS250 F/CVR 24
ꢁr add suffix ‘-E’ tꢁ mꢁdel number tꢁ receive unit with cꢁver fitted.
6. PS - Single wire parallel ꢁn ‘C’ mꢁdels ꢁnly.
Nꢁ cꢁnnectiꢁn ꢁn standard mꢁdels.
Fixing Holes:
A = #6-32 screw mꢁunting hꢁles
B = M3 x 0.5 screw mꢁunting hꢁles
†
†
Application Notes
Derating Curve
Signals
100
1. Tꢁ turn ꢁff the ꢁutput, apply 5 V tꢁ the remꢁte On/Off.
2. AC OK is a TTL signal which gꢁes LOW when input falls belꢁw
60 VAC at rated lꢁad.
3. DC OK is a TTL signal which gꢁes LOW when PSU is in an
ꢁvercurrent cꢁnditiꢁn, ꢁvervꢁltage cꢁnditiꢁn, disabled ꢁr when
ꢁutput falls ꢁut ꢁf regulatiꢁn.
JPS250PQ with 18 CFM Fan
JPS250PQ Convection-cooled
90
80
70
60
50
40
30
20
10
L
O
A
D
(%)
4. Fꢁr AC OK and DC OK signals, sꢁurce current is 1 mA, sink
current is 6 mA.
0
0
10
20
30
40
80
50
60
70
Ambient Temperature (˚C)
JPS250
Control & Supervisory Signals
AC OK Signal
DC OK Signal
+5 V
+5 V
330 R
330 R
AC OK (HIGH)
DC OK (HIGH)
AC OK
DC OK
GND
GND
AC NOT OK (LOW)
DC NOT OK (LOW)
Parallel Connection Utilizing Optional Current Share
Remote On/Off Control (Inhibit)
Output
Supply 1
Return
OUTPUTS OFF (5V)
Remote On/Off
Ground
V1
Single Wire Parallel
LOAD
Comm
Output
Return
Supply 2
OUTPUTS ON (0 V or open circuit)
Single Wire Parallel
Remote Sense Connection
+
Output
CD
Twisted Pair
+
Sense +
Notes:
LOAD
-
CL
1. CD is 0.1 µF ceramic capacitꢁr.
2. CL i s 47 µF electrꢁlytic capacitꢁr.
Supply
Sense
-
CD
Output
-
JPS250 Fan/Cover Option
See mechanical details nꢁtes fꢁr infꢁrmatiꢁn ꢁn hꢁw tꢁ ꢁrder.
Typical internal clearance
0.15 (3.8)
4 x M3 x 6 C/S head fixing screws
in existing countersunk holes
04-June-07
相关型号:
©2020 ICPDF网 联系我们和版权申明