X84256B-2.5 [XICOR]
EEPROM, 32KX8, Serial, CMOS, PBGA8, XBGA-8;型号: | X84256B-2.5 |
厂家: | XICOR INC. |
描述: | EEPROM, 32KX8, Serial, CMOS, PBGA8, XBGA-8 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 内存集成电路 |
文件: | 总13页 (文件大小:145K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
256K
MPS™ EEPROM
X84256
µPort Saver EEPROM
DESCRIPTION
FEATURES
• 10MHz data transfer rate
• 30ns read access time
• Direct interface to microprocessors and micro-
controllers
—Eliminates I/O port requirements
—No interface glue logic required
—Eliminates need for parallel to serial converters
• Low power CMOS
The µPort Saver memories need no serial ports or
special hardware and connect to the processor mem-
ory bus. Replacing bytewide data memory, the µPort
Saver uses bytewide memory control functions, takes
a fraction of the board space and consumes much less
power. Replacing serial memories, the µPort Saver
provides all the serial benefits, such as low cost, low
power, low voltage, and small package size while
releasing I/Os for more important uses.
—2.5V–3.6V
—Standby current less than 1µA
—Active current less than 3mA
• Byte or page write capable
—64-byte page write mode
• Typical nonvolatile write cycle time: 2ms
• High reliability
—1,000,000 endurance cycles
—Guaranteed data retention: 100 years
• Small packages options
The µPort Saver memory outputs data within 30ns of
an active read signal. This is less than the read access
time of most hosts and provides “no-wait-state” opera-
tion. This prevents bottlenecks on the bus. With 10
MHz, the µPort Saver supplies data faster than
required by most host read cycle specifications. This
eliminates the need for software NOPs.
The µPort Saver memories communicate over one line
of the data bus using a sequence of standard bus read
and write operations. This “bit serial” interface allows
the µPort Saver to work well in 8-bit, 16 bit, 32-bit, and
64-bit systems.
—8-lead SOIC package
—14-lead TSSOP package
—8-lead XBGA package
A Write Protect (WP) pin prevents inadvertent writes to
the memory.
Xicor EEPROMs are designed and tested for applica-
tions requiring extended endurance. Inherent data
retention is greater than 100 years.
BLOCK DIAGRAM
Internal Block Diagram
MPS
System Connection
H.V. Generation
Timing & Control
WP
A15
µP
µC
A0
D7
DSP
ASIC
RISC
CE
I/O
OE
Command
Decode
and
Control
Logic
EEPROM
Array
32K x 8
X
DEC
D0
OE
WE
P0/CS
P1/CLK
P2/DI
Ports
Saved
WE
P3/DO
Y Decode
Data Register
Characteristics subject to change without notice. 1 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
PIN CONFIGURATIONS
PIN DESCRIPTIONS
Chip Enable (CE)
Drawings are to the same scale, actual package sizes
are shown in inches:
The Chip Enable input must be LOW to enable all read/
write operations. When CE is HIGH, the chip is dese-
lected, the I/O pin is in the high impedance state, and
unless a nonvolatile write operation is underway, the
device is in the standby power mode.
8-Lead SOIC
1
2
8
7
6
5
CE
I/O
V
CC
NC
OE
WE
WP
3
4
V
SS
Output Enable (OE)
The Output Enable input must be LOW to enable the
output buffer and to read data from the device on the I/O
line.
14-Lead TSSOP
1
2
CE
I/O
14
13
V
CC
NC
NC
NC
NC
OE
WE
Write Enable (WE)
12
11
10
9
NC
NC
NC
WP
3
4
X8401
The Write Enable input must be LOW to write either
data or command sequences to the device.
5
6
7
V
SS
8
Data In/Data Out (I/O)
Data and command sequences are serially written to
or serially read from the device through the I/O pin.
8-Lead XBGA
Write Protect (WP)
V
I/O
1
8
CC
When the Write Protect input is LOW, nonvolatile writes
to the device are disabled. When WP is HIGH, all func-
tions, including nonvolatile writes, operate normally. If a
nonvolatile write cycle is in progress, WP going LOW
will have no effect on the cycle already underway, but
will inhibit any additional nonvolatile write cycles.
CE
V
NC
2
3
7
6
SS
WE
WP
4
5
OE
DEVICE OPERATION
PIN NAMES
The X84256 serial EEPROM is designed to interface
directly with most microprocessor buses. Standard CE,
OE, and WE signals control the read and write opera-
tions, and a single l/O line is used to send and receive
data and commands serially.
Pin
I/O
Description
Data Input/Output
Chip Enable Input
Output Enable Input
Write Enable Input
Write Protect Input
Supply Voltage
Ground
CE
OE
WE
WP
Data Timing
Data input on the l/O line is latched on the rising edge
of either WE or CE, whichever occurs first. Data output
on the l/O line is active whenever both OE and CE are
LOW. Care should be taken to ensure that WE and OE
are never both LOW while CE is LOW.
V
CC
V
SS
NC
No Connect
Characteristics subject to change without notice. 2 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
Read Sequence
Write Sequence
A read sequence consists of sending a 16-bit address,
followed by the reading of data serially. The address is
written by issuing 16 separate write cycles (WE and
CE LOW, OE HIGH) to the part without a read cycle
between the write cycles. The address is sent serially,
most significant bit first, over the I/O line. Note that this
sequence is fully static, with no special timing restric-
tions, and the processor is free to perform other tasks
on the bus whenever the device CE pin is HIGH. Once
the 16 address bits are sent, a byte of data can be read
on the I/O line by issuing 8 separate read cycles (OE
and CE LOW, WE HIGH). At this point, writing a ‘1’ will
terminate the read sequence and enter the low power
standby state, otherwise the device will await further
reads in the sequential read mode.
A nonvolatile write sequence consists of sending a
reset sequence, a 16-bit address, up to 64-bytes of
data, and then a special “start nonvolatile write cycle”
command sequence.
The reset sequence is issued first (as described in the
Reset Sequence section) to set an internal write
enable latch. The address is written serially by issuing
16 separate write cycles (WE and CE LOW, OE HIGH)
to the part without any read cycles between the writes.
The address is sent serially, most significant bit first, on
the l/O pin. Up to 64-bytes of data are written by issu-
ing a multiple of 8 write cycles. Again, no read cycles
are allowed between writes.
The nonvolatile write cycle is initiated by issuing a spe-
cial read/write “1”/read sequence. The first read cycle
ends the page load, then the write “1” followed by a
read starts the nonvolatile write cycle. The device rec-
ognizes 64-byte pages (e.g., beginning at addresses
XXXXXXXXX 000000 for X84256).
Sequential Read
The byte address is automatically incremented to the
next higher address after each byte of data is read.
The data stored in the memory at the next address can
be read sequentially by continuing to issue read
cycles. When the highest address in the array is
reached, the address counter rolls over to address
$0000 and reading may be continued indefinitely.
When sending data to the part, attempts to exceed the
upper address of the page will result in the address
counter “wrapping-around” to the first address on the
page, where data loading can continue. For this rea-
son, sending more than 512 consecutive data bits will
result in overwriting previous data.
Reset Sequence
The reset sequence resets the device and sets an
internal write enable latch. A reset sequence can be
sent at any time by performing a read/write “0”/read
operation (see Figs. 1 and 2). This breaks the multiple
read or write cycle sequences that are normally used
to read from or write to the part. The reset sequence
can be used at any time to interrupt or end a sequential
read or page load. As soon as the write “0” cycle is
complete, the part is reset (unless a nonvolatile write
cycle is in progress). The second read cycle in this
sequence, and any further read cycles, will read a
HIGH on the l/O pin until a valid read sequence (which
includes the address) is issued. The reset sequence
must be issued at the beginning of both read and write
sequences to be sure the device initiates these opera-
tions properly.
A nonvolatile write cycle will not start if a partial or
incomplete write sequence is issued. The internal write
enable latch is reset when the nonvolatile write cycle is
completed and after an invalid write to prevent inad-
vertent writes. Note that this sequence is fully static,
with no special timing restrictions. The processor is
free to perform other tasks on the bus whenever the
chip enable pin (CE) is HIGH.
Characteristics subject to change without notice. 3 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
Figure 1. Read Sequence
CE
OE
WE
"0"
A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
I/O (IN)
D7 D6 D5 D4 D3 D2 D1 D0
I/O (OUT)
RESET
Load Address
Read Data
When Accessing: X84256 Array: A15 = 0
Figure 2. Write Sequence
CE
OE
WE
"0"
A10
I/O (IN)
A15 A14 A13 A12 A11
A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0
"1"
"0"
I/O (OUT)
RESET
Load Address
Load Data
START
Nonvolatile
Write
When Accessing: X84256 Array: A15 = 0
Nonvolatile Write Status
cycle is complete, the l/O pin goes HIGH. A reset
sequence can also be issued during a nonvolatile write
cycle with the same result: I/O is LOW as long as a
nonvolatile write cycle is in progress, and l/O is HIGH
when the nonvolatile write cycle is done.
The status of a nonvolatile write cycle can be deter-
mined at any time by simply reading the state of the l/O
pin on the device. This pin is read when OE and CE
are LOW and WE is HIGH. During a nonvolatile write
cycle the l/O pin is LOW. When the nonvolatile write
Characteristics subject to change without notice. 4 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
Low Power Operation
Write Protection
The device enters an idle state, which draws minimal
current when:
A special “start nonvolatile write” command sequence is
required to start a nonvolatile write cycle (See Figure 2).
– an illegal sequence is entered. The following are the
more common illegal sequences:
SYMBOL TABLE
• Read/Write/Write—any time
WAVEFORM
INPUTS
OUTPUTS
• Read/Write ‘1’—When writing the address or writing
data.
Must be
steady
Will be
steady
• Write ‘1’—when reading data
May change
from LOW to
HIGH
Will change
from LOW to
HIGH
• Read/Read/Write ‘1’—after data is written to
device, but before entering the NV write sequence.
May change
Will change
from HIGH to from HIGH to
• the device powers-up;
LOW
LOW
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
• a nonvolatile write operation completes.
While a sequential read is in progress, the device remains
in an active state. This state draws more current than
the idle state, but not as much as during a read itself.
To go back to the lowest power condition, an invalid
condition is created by writing a ‘1’ after the last bit of a
read operation.
N/A
Center Line
is High
Impedance
Characteristics subject to change without notice. 5 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
ABSOLUTE MAXIMUM RATINGS
COMMENT
Temperature under bias ....................–65°C to +135°C
Storage temperature .........................–65°C to +150°C
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those indi-
cated in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability.
Terminal voltage with respect to V ..........–1V to +5V
SS
DC output current................................................. 5mA
Lead temperature (soldering, 10 seconds).........300°C
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Min.
0°C
Max.
+70°C
+85°C
+125°C
Supply Voltage
Limits
X84256–2.5
2.5V to 3.6V
–40°C
–55°C
Military†
†
Contact factory for availability.
D.C. OPERATING CHARACTERISTICS (V
= 2.5V to 3.6V)
CC
(Over the recommended operating conditions, unless otherwise specified.)
Limits
Symbol
Parameter
Min.
Max.
Unit
Test Conditions
OE = V , WE = V , I/O = Open, CE
clocking @ 10MHz
I during nonvolatile write cycle all inputs
CC
I
V
V
V
supply current (Read)
1
mA
CC1
CC
CC
CC
IL
IH
I
supply current (Write)
3
mA
CC2
at CMOS levels
CE = V , other inputs = V or V
SS
I
standby current
1
µA
µA
µA
V
SB1
CC
CC
I
Input leakage current
Output leakage current
Input LOW voltage
10
10
V
V
= V to V
SS CC
LI
IN
I
= V to V
SS CC
LO
OUT
(1)
lL
V
–0.5
V
x 0.3
CC
(1)
V
Input HIGH voltage
Output LOW voltage
Output HIGH voltage
V
V
x 0.7
V
+ 0.5
V
IH
CC
CC
V
0.4
V
I = 1mA, V = 3V
OL CC
OL
V
– 0.4
V
I
= –400µA, V = 3V
OH CC
OH
CC
Note: (1)V Min. and V Max. are for reference only and are not tested.
IL
IH
CAPACITANCE T = +25°C, F = 1MHZ, V
= 3V
A
CC
Symbol
Parameter
Max.
Unit
pF
Test Conditions
(2)
I/O
C
Input/Output capacitance
Input capacitance
8
6
V
= 0V
= 0V
I/O
(2)
IN
C
pF
V
IN
Note: (2) Periodically sampled, but not 100% tested.
Characteristics subject to change without notice. 6 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
POWER-UP TIMING
Symbol
Parameter
Power-up to Read operation
Power-up to Write operation
Max.
Unit
ms
(3)
PUR
t
2
5
(3)
PUW
t
ms
Note: (3) Time delays required from the time the V is stable until the specific operation can be initiated. Periodically sampled, but not 100%
CC
tested.
A.C. CONDITIONS OF TEST
EQUIVALENT A.C. LOAD CIRCUITS
Input pulse levels
V
x 0.1 to V x 0.9
CC
CC
3V
Input rise and fall times
Input and Output timing levels
5ns
2.39KΩ
V
x 0.5
CC
Output
4.58KΩ
30pF
A.C. CHARACTERISTICS (Over the recommended operating conditions, unless otherwise specified.)
Read Cycle Limits–X84256
V
= 2.5V–3.6V
CC
Symbol
Parameter
Min.
Max.
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
Read cycle time
CE access time
OE access time
OE pulse width
100
RC
t
30
30
CE
OE
t
t
50
50
50
50
0
OEL
t
OE high recovery time
CE LOW time
OEH
t
LOW
t
CE HIGH time
HIGH
(4)
t
CE LOW to output in low Z
CE HIGH to output in high Z
OE LOW to output in low Z
OE HIGH to output in high Z
Output hold from CE or OE HIGH
WE HIGH setup time
LZ
(4)
HZ
t
0
30
30
(4)
OLZ
t
0
(4)
OHZ
t
0
t
0
OH
t
25
25
WES
t
WE HIGH hold time
WEH
Note: (4) Periodically sampled, but not 100% tested. t
and t
are measured from the point where CE or OE goes HIGH (whichever
OHZ
HZ
occurs first) to the time when I/O is no longer being driven into a 5pF load.
Characteristics subject to change without notice. 7 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
t
RC
t
t
HIGH
LOW
t
CE
CE
WE
OE
t
WES
t
OEL
t
OEH
t
OE
t
WEH
t
OHZ
I/O
HIGH Z
Data
t
OH
t
t
OLZ
LZ
t
HZ
Write Cycle Limits–X84256
V
= 2.5V–3.6V
CC
Symbol
Parameter
Min.
Max.
Unit
ms
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
(5)
NVWC
t
Nonvolatile write cycle time
Write cycle time
5
t
100
35
65
0
WC
t
WE pulse width
WP
t
WE HIGH recovery time
Write setup time
WPH
t
CS
t
Write hold time
0
CH
t
CE pulse width
35
65
25
25
20
5
CP
t
CE HIGH recovery time
OE HIGH setup time
OE HIGH hold time
Data setup time
CPH
t
OES
t
OEH
(6)
t
DS
(6)
DH
t
Data hold time
(7)
(7)
t
WP HIGH setup
100
100
WPSU
WPHD
t
WP HIGH hold
Notes: (5) t
is the time from the falling edge of OE or CE (whichever occurs last) of the second read cycle in the “start nonvolatile write
NVWC
cycle” sequence until the self-timed, internal nonvolatile write cycle is completed.
(6) Data is latched into the X84256 on the rising edge of CE or WE, whichever occurs first.
(7) Periodically sampled, but not 100% tested.
Characteristics subject to change without notice. 8 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
CE Controlled Write Cycle
t
CPH
t
CP
CE
t
t
OEH
OES
OE
WE
WP
I/O
t
CS
t
CH
t
WP
t
WPH
t
t
WPSU
WPHD
Data
t
t
DS
DH
HIGH Z
t
WC
WE Controlled Write Cycle
t
CPH
t
CP
CE
t
OES
t
OE
WE
WP
I/O
CS
t
CH
t
OEH
t
WPH
t
WP
t
WPHD
t
WPSU
t
t
DS
DH
HIGH Z
Data
t
WC
Characteristics subject to change without notice. 9 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
PACKAGING INFORMATION
8-Lead XBGA
Complete Part Number
X84256Z-2.5/B-2.5
Top Mark
XAAD
X84256: Bottom View
A1
X84256Z1-2.5/BI-2.5
XACR
V
CC
I/O
CE
X84256: Top View
NC
V
I/O
1
8
CC
CE
V
NC
2
3
7
6
E
E
V
WE
SS
SS
WE
WP
4
5
OE
e
OE
WP
D
D
A1
8-Lead XBGA
A
DWQ Symbol
Z
B
A
A1
C
D
E
Contact Factory
Contact Factory
Contact Factory
Contact Factory
Contact Factory
Contact Factory
Contact Factory
Contact Factory
Contact Factory
Contact Factory
Contact Factory
Contact Factory
Contact Factory
Contact Factory
e
F
NOTE: ALL DIMENSIONS IN µM
ALL DIMENSIONS ARE TYPICAL VALUES
Characteristics subject to change without notice. 10 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
PACKAGING INFORMATION
8-Lead Plastic Small Outline Gull Wing Package Type S
0.150 (3.80) 0.228 (5.80)
0.158 (4.00) 0.244 (6.20)
Pin 1 Index
Pin 1
0.014 (0.35)
0.019 (0.49)
0.188 (4.78)
0.197 (5.00)
(4X) 7°
0.053 (1.35)
0.069 (1.75)
0.004 (0.19)
0.010 (0.25)
0.050 (1.27)
0.010 (0.25)
0.050" Typical
X 45°
0.020 (0.50)
0.050"
Typical
0° - 8°
0.0075 (0.19)
0.010 (0.25)
0.250"
0.016 (0.410)
0.037 (0.937)
0.030"
Typical
8 Places
FOOTPRINT
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
Characteristics subject to change without notice. 11 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
PACKAGING INFORMATION
14-Lead Plastic, TSSOP, Package Type V
.025 (.65) BSC
.169 (4.3)
.177 (4.5)
.252 (6.4) BSC
.193 (4.9)
.200 (5.1)
.047 (1.20)
.0075 (.19)
.0118 (.30)
.002 (.05)
.006 (.15)
.010 (.25)
Gage Plane
0° - 8°
Seating Plane
.019 (.50)
.029 (.75)
Detail A (20X)
.031 (.80)
.041 (1.05)
See Detail “A”
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
Characteristics subject to change without notice. 12 of 13
REV 1.1 11/22/00
www.xicor.com
X84256
Ordering Information
X84256
X
X
–X
V
Range
CC
Device
Blank = 2.5V to 3.6V, 10 MHz
Temperature Range
25 = Commercial = 0°C to +70°C
I = Industrial = –40°C to +85°C
Military = –55°C to +125°C (contact factory)
Packages
X84256
S8 = 8-Lead SOIC
V14 = 14-Lead TSSOP
Z = 8-Lead XBGA
B = 8-Lead XBGA
Part Mark Convention
14-Lead TSSOP
8-Lead XBGA
8-Lead SOIC
Complete Part Number Top Mark
Blank = 8-Lead SOIC
YWW
X84256 X
XX
84256X
X84256Z–2.5
X84256ZI–2.5
X84256B–2.5
X84256BI–2.5
XABA
XABB
Blank = 2.5 to 3.6V, 0 to +70°C
I = 2.5 to 3.6V, -40 to +85°C
Blank = 2.5 to 3.6V, 0 to +70°C
I = 2.5 to 3.6V, -40 to +85°C
XABA
XABB
©Xicor, Inc. 2000 Patents Pending
LIMITED WARRANTY
Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty,
express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement.
Xicor, Inc. makes no warranty of merchantability or fitness for any purpose. Xicor, Inc. reserves the right to discontinue production and change specifications and prices
at any time and without notice.
Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, or licenses are implied.
TRADEMARK DISCLAIMER:
Xicor and the Xicor logo are registered trademarks of Xicor, Inc. AutoStore, Direct Write, Block Lock, SerialFlash, MPS, and XDCP are also trademarks of Xicor, Inc. All
others belong to their respective owners.
U.S. PATENTS
Xicor products are covered by one or more of the following U.S. Patents: 4,326,134; 4,393,481; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846;
4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829,482; 4,874,967; 4,883,976; 4,980,859; 5,012,132; 5,003,197; 5,023,694; 5,084,667; 5,153,880; 5,153,691;
5,161,137; 5,219,774; 5,270,927; 5,324,676; 5,434,396; 5,544,103; 5,587,573; 5,835,409; 5,977,585. Foreign patents and additional patents pending.
LIFE RELATED POLICY
In situations where semiconductor component failure may endanger life, system designers using this product should design the system with appropriate error detection
and correction, redundancy and back-up features to prevent such an occurrence.
Xicor’s products are not authorized for use in critical components in life support devices or systems.
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to
perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or effectiveness.
Characteristics subject to change without notice. 13 of 13
REV 1.1 11/22/00
www.xicor.com
相关型号:
©2020 ICPDF网 联系我们和版权申明