WM8196SCDS/R [WOLFSON]
(8 + 8) Bit Output 16-bit CIS/CCD AFE/Digitiser; （8 + 8）位输出16位CIS / CCD AFE /数字转换器
| 型号： | WM8196SCDS/R |
| 厂家： | 
WOLFSON MICROELECTRONICS PLC |
| 描述： | (8 + 8) Bit Output 16-bit CIS/CCD AFE/Digitiser |
| 文件： | 总32页 (文件大小：364K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
WM8196
w
(8 + 8) Bit Output 16-bit CIS/CCD AFE/Digitiser
DESCRIPTION
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
16-bit ADC
The WM8196 is a 16-bit analogue front end/digitiser IC
which processes and digitises the analogue output signals
from CCD sensors or Contact Image Sensors (CIS) at pixel
sample rates of up to 12MSPS.
12MSPS conversion rate
Low power – 320mW typical
5V single supply or 5V/3.3V dual supply operation
Single or 3 channel operation
The device includes three analogue signal processing
channels each of which contains Reset Level Clamping,
Correlated Double Sampling and Programmable Gain and
Offset adjust functions. Three multiplexers allow single
channel processing. The output from each of these
channels is time multiplexed into a single high-speed 16-bit
Analogue to Digital Converter. The digital output data is
available in 8 or 4-bit wide multiplexed format.
Correlated double sampling
Programmable gain (8-bit resolution)
Programmable offset adjust (8-bit resolution)
Programmable clamp voltage
8 or 4-bit wide multiplexed data output formats
Internally generated voltage references
28-lead SSOP package
An internal 4-bit DAC is supplied for internal reference level
generation. This may be used during CDS to reference CIS
signals or during Reset Level Clamping to clamp CCD
signals. An external reference level may also be supplied.
ADC references are generated internally, ensuring optimum
performance from the device.
Serial control interface
APPLICATIONS
•
•
•
•
Flatbed and sheetfeed scanners
USB compatible scanners
Using an analogue supply voltage of 5V and a digital
interface supply of either 5V or 3.3V, the WM8196 typically
only consumes 300mW when operating from a single
5V supply.
Multi-function peripherals
High-performance CCD sensor interface
BLOCK DIAGRAM
VRLC/VBIAS
VSMP MCLK
AVDD DVDD1 DVDD2
VRT VRX VRB
w
CL
RS VS
TIMING CONTROL
WM8196
VREF/BIAS
R
8
M
U
X
OFFSET
DAC
OEB
G
B
RINP
RLC
RLC
CDS
CDS
PGA
+
+
+
+
M
U
X
I/P SIGNAL
POLARITY
ADJUST
R
G
B
8
OP[0]
OP[1]
M
U
X
OP[2]
OP[3]
OP[4]
OP[5]
DATA
I/O
PORT
16-
BIT
ADC
M
U
X
GINP
BINP
PGA
8
OP[6]
OP[7]/SDO
OFFSET
DAC
8
I/P SIGNAL
POLARITY
ADJUST
RLC
CDS
PGA
+
+
8
OFFSET
DAC
8
I/P SIGNAL
POLARITY
ADJUST
SEN
SCK
CONFIGURABLE
SERIAL
CONTROL
INTERFACE
SDI
RLC/ACYC
RLC
DAC
4
AGND1
AGND2
DGND
Production Data, March 2007, Rev 4.3
WOLFSON MICROELECTRONICS plc
Copyright ©2007 Wolfson Microelectronics plc
To receive regular email updates, sign up at http://www.wolfsonmicro.com/enews/
WM8196
Production Data
TABLE OF CONTENTS
DESCRIPTION .......................................................................................................1
FEATURES.............................................................................................................1
APPLICATIONS .....................................................................................................1
BLOCK DIAGRAM .................................................................................................1
TABLE OF CONTENTS .........................................................................................2
PIN CONFIGURATION...........................................................................................3
ORDERING INFORMATION ..................................................................................3
PIN DESCRIPTION ................................................................................................4
ABSOLUTE MAXIMUM RATINGS.........................................................................5
RECOMMENDED OPERATING CONDITIONS .....................................................5
THERMAL PERFORMANCE .................................................................................5
ELECTRICAL CHARACTERISTICS ......................................................................6
INPUT VIDEO SAMPLING............................................................................................. 8
OUTPUT DATA TIMING ................................................................................................ 8
SERIAL INTERFACE ................................................................................................... 10
INTERNAL POWER ON RESET CIRCUIT ..........................................................11
DEVICE DESCRIPTION.......................................................................................13
INTRODUCTION.......................................................................................................... 13
INPUT SAMPLING....................................................................................................... 13
RESET LEVEL CLAMPING (RLC) ............................................................................... 13
CDS/NON-CDS PROCESSING ................................................................................... 14
OFFSET ADJUST AND PROGRAMMABLE GAIN....................................................... 15
ADC INPUT BLACK LEVEL ADJUST .......................................................................... 16
OVERALL SIGNAL FLOW SUMMARY ........................................................................ 16
CALCULATING OUTPUT FOR ANY GIVEN INPUT .................................................... 16
OUTPUT FORMATS.................................................................................................... 17
CONTROL INTERFACE .............................................................................................. 18
TIMING REQUIREMENTS........................................................................................... 19
PROGRAMMABLE VSMP DETECT CIRCUIT ............................................................. 19
REFERENCES............................................................................................................. 20
POWER SUPPLY ........................................................................................................ 20
POWER MANAGEMENT............................................................................................. 20
LINE-BY-LINE OPERATION........................................................................................ 21
OPERATING MODES.................................................................................................. 22
OPERATING MODE TIMING DIAGRAMS ................................................................... 23
DEVICE CONFIGURATION .................................................................................26
REGISTER MAP.......................................................................................................... 26
REGISTER MAP DESCRIPTION................................................................................. 27
APPLICATIONS INFORMATION .........................................................................30
RECOMMENDED EXTERNAL COMPONENTS........................................................... 30
RECOMMENDED EXTERNAL COMPONENT VALUE ................................................ 30
PACKAGE DIMENSIONS ....................................................................................31
IMPORTANT NOTICE..........................................................................................32
ADDRESS:................................................................................................................... 32
PD Rev 4.3 March 2007
w
2
WM8196
Production Data
PIN CONFIGURATION
RINP
AGND2
DVDD1
OEB
1
2
3
4
5
6
7
8
28
27
26
25
24
23
22
21
GINP
BINP
VRLC/VBIAS
VRX
VSMP
VRT
RLC/ACYC
MCLK
VRB
AGND1
AVDD
DGND
SEN
DVDD2
SDI
9
20
19
18
17
16
15
OP[7]/SDO
OP[6]
10
11
12
13
14
OP[5]
SCK
OP[4]
OP[0]
OP[1]
OP[3]
OP[2]
ORDERING INFORMATION
MOISTURE
SENSITIVITY
LEVELS
TEMPERATURE
PEAK SOLDERING
TEMPERATURE
DEVICE
PACKAGE
RANGE
28-lead SSOP
(Pb free)
WM8196SCDS
WM8196SCDS/R
0 to 70oC
MSL1
260oC
28-lead SSOP
0 to 70oC
MSL1
260oC
(Pb free, tape and
reel)
Note:
Reel quantity = 2,000
PD Rev 4.3 March 2007
w
3
WM8196
Production Data
PIN DESCRIPTION
PIN
1
NAME
RINP
TYPE
Analogue input
Supply
DESCRIPTION
Red channel input video.
Analogue ground (0V).
2
AGND2
DVDD1
3
Supply
Digital supply (5V) for logic and clock generator. This must be operated at the same
potential as AVDD.
4
5
6
OEB
VSMP
Digital input
Digital input
Digital input
Output Hi-Z control, all digital outputs disabled when OEB = 1.
Video sample synchronisation pulse.
RLC/ACYC
RLC (active high) selects reset level clamp on a pixel-by-pixel basis – tie high if
used on every pixel. ACYC autocycles between R, G, B inputs.
7
MCLK
Digital input
Master clock. This clock is applied at N times the input pixel rate (N = 2, 3, 6, 8 or
any multiple of 2 thereafter depending on input sample mode).
8
DGND
SEN
Supply
Digital ground (0V).
9
Digital input
Supply
Enables the serial interface when high.
Digital supply (5V/3.3V), all digital I/O pins.
Serial data input.
10
11
12
DVDD2
SDI
Digital input
Digital input
SCK
Serial clock.
Digital multiplexed output data bus.
ADC output data (d15:d0) is available in two multiplexed formats as shown, under
the control of register MUXOP [1:0]
See ‘Output Formats’ description in Device Description section for further details.
8+8-bit
4+4+4+4-bit
A
B
A
B
C
D
13
14
15
16
17
18
19
20
OP[0]
OP[1]
Digital output
Digital output
Digital output
Digital output
Digital output
Digital output
Digital output
Digital output
d8
d0
d1
d2
d3
d4
d5
d6
d7
d9
OP[2]
d10
d11
d12
d13
d14
d15
OP[3]
OP[4]
d12
d13
d14
d15
d8
d9
d4
d5
d6
d7
d0
OP[5]
d1
d2
d3
OP[6]
d10
d11
OP[7]/SDO
Alternatively, pin OP[7]/SDO may be used to output register read-back data when
OEB = 0 and SEN has been pulsed high. See Serial Interface description in Device
Description section for further details.
21
22
23
AVDD
AGND1
VRB
Supply
Supply
Analogue supply (5V). This must be operated at the same potential as DVDD1.
Analogue ground (0V).
Analogue output Lower reference voltage.
This pin must be connected to AGND via a decoupling capacitor.
Analogue output Upper reference voltage.
This pin must be connected to AGND via a decoupling capacitor.
Analogue output Input return bias voltage.
This pin must be connected to AGND via a decoupling capacitor.
24
25
26
VRT
VRX
VRLC/VBIAS
Analogue I/O
Selectable analogue output voltage for RLC or single-ended bias reference.
This pin would typically be connected to AGND via a decoupling capacitor.
VRLC can be externally driven if programmed Hi-Z.
27
28
BINP
GINP
Analogue input
Analogue input
Blue channel input video.
Green channel input video.
PD Rev 4.3 March 2007
w
4
WM8196
Production Data
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at
or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical
Characteristics at the test conditions specified.
ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible
to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage
of this device.
Wolfson tests its package types according to IPC/JEDEC J-STD-020B for Moisture Sensitivity to determine acceptable storage
conditions prior to surface mount assembly. These levels are:
MSL1 = unlimited floor life at <30°C / 85% Relative Humidity. Not normally stored in moisture barrier bag.
MSL2 = out of bag storage for 1 year at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag.
MSL3 = out of bag storage for 168 hours at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag.
The Moisture Sensitivity Level for each package type is specified in Ordering Information.
CONDITION
MIN
MAX
Analogue supply voltage: AVDD
Digital supply voltages: DVDD1 − 2
Digital ground: DGND
GND - 0.3V
GND - 0.3V
GND - 0.3V
GND - 0.3V
GND - 0.3V
GND - 0.3V
GND - 0.3V
GND + 7V
GND + 7V
GND + 0.3V
GND + 0.3V
DVDD2 + 0.3V
AVDD + 0.3V
AVDD + 0.3V
Analogue grounds: AGND1 − 2
Digital inputs, digital outputs and digital I/O pins
Analogue inputs (RINP, GINP, BINP)
Other pins
°
°
Operating temperature range: TA
Storage temperature prior to soldering
Storage temperature after soldering
Notes:
0 C
+70 C
°
30 C max / 85% RH max
°
°
+150 C
-65 C
1.
2.
GND denotes the voltage of any ground pin.
AGND1, AGND2 and DGND pins are intended to be operated at the same potential. Differential voltages
between these pins will degrade performance.
RECOMMENDED OPERATING CONDITIONS
CONDITION
SYMBOL
TA
MIN
0
TYP
MAX
70
UNITS
Operating temperature range
Analogue supply voltage
Digital core supply voltage
Digital I/O supply voltage
°C
V
AVDD
DVDD1
4.75
4.75
5.0
5.0
5.25
5.25
V
5V I/O
DVDD2
DVDD2
4.75
2.97
5.0
3.3
5.25
3.63
V
V
3.3V I/O
THERMAL PERFORMANCE
PARAMETER
Performance
SYMBOL
RθJC
RθJA
TEST CONDITIONS
MIN
TYP
23.9
67.1
MAX
UNIT
°C/W
°C/W
Thermal resistance – junction to
case
T
ambient = 25°C
Thermal resistance – junction to
ambient
Notes:
1. Figures given are for package mounted on 4-layer FR4 according to JESD51-5 and JESD51-7.
PD Rev 4.3 March 2007
5
w
WM8196
Production Data
ELECTRICAL CHARACTERISTICS
Test Conditions
AVDD = DVDD1 = 5.0V, DVDD2 = 3.3V, AGND = DGND = 0V, TA = 25°C, MCLK = 24MHz unless otherwise stated.
PARAMETER
SYMBOL
TEST
MIN
TYP
MAX
UNIT
CONDITIONS
Overall System Specification (including 16-bit ADC, PGA, Offset and CDS functions)
Conversion Rate
12
0.4
MSPS
Vp-p
Vp-p
V
Full-scale input voltage range
(see Note 1)
4.08
Input signal limits (see Note 2)
Full-scale transition error
VIN
0
AVDD
Gain = 0dB;
PGA[7:0] = 4B(hex)
20
20
mV
Zero-scale transition error
Gain = 0dB;
mV
PGA[7:0] = 4B(hex)
Differential non-linearity
Integral non-linearity
DNL
INL
1.25
25
LSB
LSB
Channel to channel gain matching
Total output noise
1
%
Min Gain
Max Gain
4.5
14
LSB rms
LSB rms
References
Upper reference voltage
VRT
VRB
VRX
VRTB
2.85
1.35
1.65
1.5
V
V
V
V
Ω
Lower reference voltage
Input return bias voltage
1.4
1.6
Diff. reference voltage (VRT-VRB)
Output resistance VRT, VRB, VRX
VRLC/Reset-Level Clamp (RLC)
RLC switching impedance
VRLC short-circuit current
VRLC output resistance
1
50
2
Ω
mA
Ω
2
VRLC Hi-Z leakage current
RLCDAC resolution
VRLC = 0 to AVDD
AVDD=5V
1
µA
4
bits
V/step
V/step
V
RLCDAC step size, RLCDAC = 0
RLCDAC step size, RLCDAC = 1
VRLCSTEP
VRLCSTEP
VRLCBOT
0.25
0.17
0.39
RLCDAC output voltage at
AVDD=5V
code 0(hex), RLCDACRNG = 0
RLCDAC output voltage at
code 0(hex), RLCDACRNG = 1
VRLCBOT
VRLCTOP
VRLCTOP
0.26
4.16
2.81
V
V
RLCDAC output voltage at
code F(hex) RLCDACRNG, = 0
AVDD=5V
RLCDAC output voltage at
V
code F(hex), RLCDACRNG = 1
VRLC deviation
-50
+50
mV
Offset DAC, Monotonicity Guaranteed
Resolution
8
bits
LSB
Differential non-linearity
Integral non-linearity
Step size
DNL
INL
0.1
0.5
1
0.25
2.04
-260
+260
LSB
mV/step
mV
Output voltage
Code 00(hex)
Code FF(hex)
mV
Notes:
1.
2.
Full-scale input voltage denotes the maximum amplitude of the input signal at the specified gain.
Input signal limits are the limits within which the full-scale input voltage signal must lie.
PD Rev 4.3 March 2007
6
w
WM8196
Production Data
Test Conditions
AVDD = DVDD1 = 5.0V, DVDD2 = 3.3V, AGND = DGND = 0V, TA = 25°C, MCLK = 24MHz unless otherwise stated.
PARAMETER
SYMBOL
TEST
MIN
TYP
MAX
UNIT
CONDITIONS
Programmable Gain Amplifier
Resolution
Gain
8
208
bits
V/V
283 − PGA[7 : 0]
Max gain, each channel
Min gain, each channel
Gain error, each channel
Analogue to Digital Converter
Resolution
GMAX
GMIN
7.4
0.74
1
V/V
V/V
%
16
12
3
Bits
MSPS
V
Speed
Full-scale input range
(2*(VRT-VRB))
DIGITAL SPECIFICATIONS
Digital Inputs
High level input voltage
Low level input voltage
High level input current
Low level input current
Input capacitance
VIH
VIL
IIH
0.8 ∗ DVDD2
V
0.2 ∗ DVDD2
V
1
1
µA
µA
pF
IIL
CI
5
Digital Outputs
High level output voltage
Low level output voltage
High impedance output current
Digital IO Pins
VOH
VOL
IOZ
IOH = 1mA
IOL = 1mA
DVDD2 - 0.5
V
V
0.5
1
µA
Applied high level input voltage
Applied low level input voltage
High level output voltage
Low level output voltage
Low level input current
High level input current
Input capacitance
VIH
VIL
VOH
VOL
IIL
0.8 ∗ DVDD2
V
V
0.2 ∗ DVDD2
IOH = 1mA
IOL = 1mA
DVDD2 - 0.5
V
0.5
1
V
µA
µA
pF
µA
IIH
1
CI
5
High impedance output current
Supply Currents
IOZ
1
Total supply current − active
(Three channel mode)
Total supply current − active
(Single channel mode)
60
45
mA
mA
MCLK = 24MHz
LINEBYLINE = 1
MCLK = 24MHz
Total analogue supply current −
IAVDD
IAVDD
56
41
mA
mA
MCLK = 24MHz
active (Three channel mode)
Total analogue supply current −
active (One channel mode)
LINEBYLINE = 1
MCLK = 24MHz
Digital core supply current,
DVDD1 − active (Note1)
Digital I/O supply current,
DVDD2 − active (Note1)
Supply current − full power down
mode
3
1
mA
mA
µA
MCLK = 24MHz
MCLK = 24MHz
300
PD Rev 4.3 March 2007
7
w
WM8196
Production Data
INPUT VIDEO SAMPLING
tPER
tMCLKH tMCLKL
MCLK
tVSMPH
tVSMPSU
VSMP
INPUT
tVSU
tVH
tRSU
tRH
VIDEO
Figure 1 Input Video Timing
Note:
1.
See Page 14 (Programmable VSMP Detect Circuit) for video sampling description.
Test Conditions
AVDD = DVDD1 = 5.0V, DVDD2 = 3.3V, AGND = DGND = 0V, TA = 25°C, MCLK = 24MHz unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
MCLK period
tPER
41.6
ns
MCLK high period
MCLK low period
VSMP set-up time
VSMP hold time
tMCLKH
tMCLKL
tVSMPSU
tVSMPH
tVSU
18.8
18.8
6
ns
ns
ns
ns
ns
ns
ns
ns
3
Video level set-up time
Video level hold time
Reset level set-up time
Reset level hold time
Notes:
10
3
tVH
tRSU
10
3
tRH
1.
2.
tVSU and tRSU denote the set-up time required after the input video signal has settled.
Parameters are measured at 50% of the rising/falling edge.
OUTPUT DATA TIMING
MCLK
tPD
OP[7:0]
Figure 2 Output Data Timing
PD Rev 4.3 March 2007
8
w
WM8196
Production Data
OEB
tPZE
tPEZ
OP[7:0]
Hi-Z
Hi-Z
Figure 3 Output Data Enable Timing
Test Conditions
AVDD = DVDD1 = 5.0V, DVDD2 = 3.3V, AGND = DGND = 0V, TA = 25°C, MCLK = 24MHz unless otherwise stated.
PARAMETER
SYMBOL
tPD
TEST CONDITIONS
IOH = 1mA, IOL = 1mA
MIN
TYP
MAX
40
UNITS
ns
Output propagation delay
Output enable time
Output disable time
tPZE
20
ns
tPEZ
15
ns
MCLK
tACYCSU
tACYCH
tACYCH
tACYCSU
RLC/ACYC
PGA/OFFSET
MUX OUTPUT
Figure 4 Auto Cycle Timing
Test Conditions
AVDD = DVDD1 = 5.0V, DVDD2 = 3.3V, AGND = DGND = 0V, TA = 25°C, MCLK = 24MHz unless otherwise stated.
PARAMETER
SYMBOL
tACYCSU
tACYCH
TEST CONDITIONS
MIN
6
TYP
MAX
UNITS
ns
Auto Cycle set-up time
Auto Cycle hold time
3
ns
PD Rev 4.3 March 2007
9
w
WM8196
Production Data
SERIAL INTERFACE
tSPER
tSCKL tSCKH
SCK
tSSU
tSH
SDI
SEN
SDO
tSCE
tSEW tSEC
tSCRDZ
LSB
tSERD
tSCRD
ADC
DATA
ADC DATA
MSB
REGISTER DATA
Figure 5 Serial Interface Timing
Test Conditions
AVDD = DVDD1 = 5.0V, DVDD2 = 3.3V, AGND = DGND = 0V, TA = 25°C, MCLK = 24MHz unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
SCK period
tSPER
41.6
ns
SCK high
tSCKH
tSCKL
tSSU
18.8
18.8
6
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
SCK low
SDI set-up time
SDI hold time
tSH
6
SCK to SEN set-up time
SEN to SCK set-up time
SEN pulse width
tSCE
12
12
25
tSEC
tSEW
tSERD
tSCRD
tSCRDZ
SEN low to SDO = Register data
SCK low to SDO = Register data
SCK low to SDO = ADC data
30
30
30
Note:
1. Parameters are measured at 50% of the rising/falling edge
PD Rev 4.3 March 2007
10
w
WM8196
Production Data
INTERNAL POWER ON RESET CIRCUIT
Figure 6 Internal Power On Reset Circuit Schematic
The WM8196 includes an internal Power-On-Reset Circuit, as shown in Figure 6, which is used to
reset the digital logic into a default state after power up. The POR circuit is powered from AVDD and
monitors DVDD1. It asserts PORB low if AVDD or DVDD1 is below a minimum threshold.
The power supplies can be brought up in any order but is important that either AVDD is brought up
and is stable before DVDD comes up or vice versa as shown in Figure 7 and Figure 8.
Figure 7 Typical Power up Sequence where AVDD is Powered before DVDD1
Figure 7 shows a typical power-up sequence where AVDD is powered up first. When AVDD rises
above the minimum threshold, Vpora, there is enough voltage for the circuit to guarantee PORB is
asserted low and the chip is held in reset. In this condition, all writes to the control interface are
ignored. Now AVDD is at full supply level. Next DVDD1 rises to Vpord_on and PORB is released
high and all registers are in their default state and writes to the control interface may take place.
On power down, where AVDD falls first, PORB is asserted low whenever AVDD drops below the
minimum threshold Vpora_off.
PD Rev 4.3 March 2007
11
w
WM8196
Production Data
Figure 8 Typical Power up Sequence where DVDD1 is Powered before AVDD
Figure 8 shows a typical power-up sequence where DVDD1 is powered up first. It is assumed that
DVDD1 is already up to specified operating voltage. When AVDD goes above the minimum
threshold, Vpora, there is enough voltage for the circuit to guarantee PORB is asserted low and the
chip is held in reset. In this condition, all writes to the control interface are ignored. When AVDD rises
to Vpora_on, PORB is released high and all registers are in their default state and writes to the
control interface may take place.
On power down, where DVDD1 falls first, PORB is asserted low whenever DVDD1 drops below the
minimum threshold Vpord_off.
SYMBOL
Vpora
TYP
0.6
1.2
0.6
0.7
0.6
UNIT
V
V
V
V
V
Vpora_on
Vpora_off
Vpord_on
Vpord_off
Table 1 Typical POR Operation (typical values, not tested)
Note: It is recommended that every time power is cycled to the WM8196 a software reset is written
to the software register to ensure that the contents of the control registers are at their default values
before carrying out any other register writes.
PD Rev 4.3 March 2007
12
w
WM8196
Production Data
DEVICE DESCRIPTION
INTRODUCTION
A block diagram of the device showing the signal path is presented on Page 1.
The WM8196 samples up to three inputs (RINP, GINP and BINP) simultaneously. The device then
processes the sampled video signal with respect to the video reset level or an internally/externally
generated reference level using either one or three processing channels.
Each processing channel consists of an Input Sampling block with optional Reset Level Clamping
(RLC) and Correlated Double Sampling (CDS), an 8-bit programmable offset DAC and an 8-bit
Programmable Gain Amplifier (PGA).
The ADC then converts each resulting analogue signal to a 16-bit digital word. The digital output from
the ADC is presented on an 8-bit wide bi-directional bus, with optional 8 or 4-bit multiplexed formats.
On-chip control registers determine the configuration of the device, including the offsets and gains
applied to each channel. These registers are programmable via a serial interface.
INPUT SAMPLING
The WM8196 can sample and process one to three inputs through one or three processing channels
as follows:
Colour Pixel-by-Pixel: The three inputs (RINP, GINP and BINP) are simultaneously sampled for
each pixel and a separate channel processes each input. The signals are then multiplexed into the
ADC, which converts all three inputs within the pixel period.
Monochrome: A single chosen input (RINP, GINP, or BINP) is sampled, processed by the
corresponding channel, and converted by the ADC. The choice of input and channel can be changed
via the control interface, e.g. on a line-by-line basis if required.
Colour Line-by-Line: A single chosen input (RINP, GINP, or BINP) is sampled and multiplexed into
the red channel for processing before being converted by the ADC. The input selected can be
switched in turn (RINP → GINP → BINP → RINP…) together with the PGA and Offset DAC control
registers by pulsing the RLC/ACYC pin. This is known as auto-cycling. Alternatively, other sampling
sequences can be generated via the control registers. This mode causes the blue and green
channels to be powered down. Refer to the Line-by-Line Operation section for more details.
RESET LEVEL CLAMPING (RLC)
To ensure that the signal applied to the WM8196 lies within its input range (0V to AVDD) the CCD
output signal is usually level shifted by coupling through a capacitor, CIN. The RLC circuit clamps the
WM8196 side of this capacitor to a suitable voltage during the CCD reset period.
A typical input configuration is shown in Figure 9. An internal clamp pulse, CL, is generated from
MCLK and VSMP by the Timing Control Block. When CL is active the voltage on the WM8196 side of
CIN, at RINP, is forced to the VRLC/VBIAS voltage (VVRLC ) by closing of switch 1. When the CL
pulse turns off switch 1 opens, the voltage at RINP initially remains at VVRLC but any subsequent
variation in sensor voltage (from reset to video level) will couple through CIN to RINP.
RLC is compatible with both CDS and non-CDS operating modes, as selected by switch 2. Refer to
the CDS/non-CDS Processing section.
PD Rev 4.3 March 2007
13
w
WM8196
Production Data
RLC/ACYC MCLK VSMP
TIMING CONTROL
FROM CONTROL
INTERFACE
CL
RS
VS
CIN
S/H
+
-
TO OFFSET DAC
+
RINP
2
S/H
1
RLC
CDS
INPUT SAMPLING
BLOCK FOR RED
CHANNEL
EXTERNAL VRLC
CDS
VRLC/
VBIAS
4-BIT
RLC DAC
FROM CONTROL
INTERFACE
VRLCEXT
Figure 9 Reset Level Clamping and CDS Circuitry
If auto-cycling is not required, RLC can be selected by pin RLC/ACYC. Figure 10 illustrates control of
RLC for a typical CCD waveform, with CL applied during the reset period.
The input signal applied to the RLC/ACYC pin is sampled on the positive edge of MCLK that occurs
during each VSMP pulse. The sampled level, high (or low) controls the presence (or absence) of the
internal CL pulse on the next reset level. The position of CL can be adjusted by using control bits
CDSREF[1:0] (Figure 11).
If auto-cycling is required, pin RLC/ACYC is no longer available for this function and control bit
RLCINT determines whether clamping is applied.
MCLK
VSMP
ACYC/RLC
or RLCINT
1
X
X
0
X
X
0
Programmable Delay
CL
(CDSREF = 01)
INPUT VIDEO
RGB
RGB
RGB
RLC on this Pixel
No RLC on this Pixel
Figure 10 Relationship of RLC Pin, MCLK and VSMP to Internal Clamp Pulse, CL
The VRLC/VBIAS pin can be driven internally by a 4-bit DAC (RLCDAC) by writing to control bits
RLCV[3:0]. The RLCDAC range and step size may be increased by writing to control bit
RLCDACRNG. Alternatively, the VRLC/VBIAS pin can be driven externally by writing to control bit
VRLCEXT to disable the RLCDAC and then applying a d.c. voltage to the pin.
CDS/NON-CDS PROCESSING
For CCD type input signals, the signal may be processed using CDS, which will remove pixel-by-pixel
common mode noise. For CDS operation, the video level is processed with respect to the video reset
level, regardless of whether RLC has been performed. To sample using CDS, control bit CDS must
be set to 1 (default), this sets switch 2 into the position shown in Figure 9 and causes the signal
reference to come from the video reset level. The time at which the reset level is sampled, by clock
Rs/CL, is adjustable by programming control bits CDSREF[1:0], as shown in Figure 11.
PD Rev 4.3 March 2007
14
w
WM8196
Production Data
MCLK
VSMP
VS
RS/CL (CDSREF = 00)
RS/CL (CDSREF = 01)
RS/CL (CDSREF = 10)
RS/CL (CDSREF = 11)
Figure 11 Reset Sample and Clamp Timing
For CIS type sensor signals, non-CDS processing is used. In this case, the video level is processed
with respect to the voltage on pin VRLC/VBIAS, generated internally or externally as described
above. The VRLC/VBIAS pin is sampled by Rs at the same time as Vs samples the video level in this
mode; non-CDS processing is achieved by setting switch 2 in the lower position, CDS = 0.
OFFSET ADJUST AND PROGRAMMABLE GAIN
The output from the CDS block is a differential signal, which is added to the output of an 8-bit Offset
DAC to compensate for offsets and then amplified by an 8-bit PGA. The gain and offset for each
channel are independently programmable by writing to control bits DAC[7:0] and PGA[7:0].
The gain characteristic of the WM8196 PGA is shown in Figure 12. Figure 13 shows the maximum
device input voltage that can be gained up to match the ADC full-scale input range (3V).
8
7
6
5
4
3
2
1
0
4.5
4
3.5
3
2.5
2
1.5
1
0.5
0
0
64
128
192
256
0
64
128
192
256
Gain register value (PGA[7:0])
Gain register value (PGA[7:0])
Figure 12 PGA Gain Characteristic
Figure 13 Peak Input Voltage to Match ADC Full-scale Range
In colour line-by-line mode the gain and offset coefficients for each colour can be multiplexed in order
(Red → Green → Blue → Red…) by pulsing the ACYC/RLC pin, or controlled via the FME,
ACYCNRLC and INTM[1:0] bits. Refer to the Line-by-Line Operation section for more details.
PD Rev 4.3 March 2007
15
w
WM8196
Production Data
ADC INPUT BLACK LEVEL ADJUST
The output from the PGA should be offset to match the full-scale range of the ADC (3V). For
negative-going input video signals, a black level (zero differential) output from the PGA should be
offset to the top of the ADC range by setting register bits PGAFS[1:0]=10. For positive going input
signal the black level should be offset to the bottom of the ADC range by setting PGAFS[1:0]=11.
Bipolar input video is accommodated by setting PGAFS[1:0]=00 or PGAFS[1:0]=01 (zero differential
input voltage gives mid-range ADC output).
OVERALL SIGNAL FLOW SUMMARY
Figure 14 represents the processing of the video signal through the WM8196.
OUTPUT
INVERT
BLOCK
INPUT
SAMPLING
BLOCK
OFFSET DAC PGA
ADC BLOCK
BLOCK
BLOCK
D2
x (65535/VFS
)
V1
V2
V3
D1
+0
if PGAFS[1:0]=11
X
+65535 if PGAFS[1:0]=10
+32768 if PGAFS[1:0]=0x
OP[7:0]
+
+
VIN
digital
analog
+
-
CDS = 1
CDS = 0
D2 = D1 if INVOP = 0
D2 = 65535-D1 if INVOP = 1
VRESET
PGA gain
A = 208/(283-PGA[7:0])
VVRLC
Offset
DAC
260mV*(DAC[7:0]-127.5)/127.5
VIN is RINP or GINP or BINP
VRESET is VIN sampled during reset clamp
VRLC is voltage applied to VRLC pin
RLCEXT=1
RLCEXT=0
CDS, RLCEXT,RLCV[3:0], DAC[7:0],
PGA[7:0], PGAFS[1:0] and INVOP are set
by programming internal control registers.
CDS=1 for CDS, 0 for non-CDS
RLC
DAC
See parametrics for
DAC voltages.
Figure 14 Overall Signal Flow
The INPUT SAMPLING BLOCK produces an effective input voltage V1. For CDS, this is the
difference between the input video level VIN and the input reset level VRESET. For non-CDS this is the
difference between the input video level VIN and the voltage on the VRLC/VBIAS pin, VVRLC
optionally set via the RLC DAC.
,
The OFFSET DAC BLOCK then adds the amount of fine offset adjustment required to move the
black level of the input signal towards 0V, producing V2.
The PGA BLOCK then amplifies the white level of the input signal to maximise the ADC range,
outputting voltage V3.
The ADC BLOCK then converts the analogue signal, V3, to a 16-bit unsigned digital output, D1.
The digital output is then inverted, if required, through the OUTPUT INVERT BLOCK to produce D2.
CALCULATING OUTPUT FOR ANY GIVEN INPUT
The following equations describe the processing of the video and reset level signals through
the WM8196. The values if V1 V2 and V3 are often calculated in reverse order during device
setup. The PGA value is written first to set the input Voltage range, the Offset DAC is then
adjusted to compensate for any Black/Reset level offsets and finally the RLC DAC value is
set to position the reset level correctly during operation.
Note: Refer to WAN0123 for detailed information on device calibration procedures.
INPUT SAMPLING BLOCK: INPUT SAMPLING AND REFERENCING
If CDS = 1, (i.e. CDS operation) the previously sampled reset level, VRESET, is subtracted from the
input video.
V1
=
VIN - VRESET ................................................................... Eqn. 1
If CDS = 0, (non-CDS operation) the simultaneously sampled voltage on pin VRLC is subtracted
instead.
V1
=
VIN - VVRLC .................................................................... Eqn. 2
If RLCEXT = 1, VVRLC is an externally applied voltage on pin VRLC/VBIAS.
PD Rev 4.3 March 2007
16
w
WM8196
Production Data
If RLCEXT = 0, VVRLC is the output from the internal RLC DAC.
VVRLC
=
(VRLCSTEP ∗ RLCV[3:0]) + VRLCBOT ................................. Eqn. 3
V
RLCSTEP is the step size of the RLC DAC and VRLCBOT is the minimum output of the RLC DAC.
OFFSET DAC BLOCK: OFFSET (BLACK-LEVEL) ADJUST
The resultant signal V1 is added to the Offset DAC output.
V2
=
V1 + {260mV ∗ (DAC[7:0]-127.5) } / 127.5 ..................... Eqn. 4
PGA NODE: GAIN ADJUST
The signal is then multiplied by the PGA gain,
V3
=
V2 ∗ 208/(283- PGA[7:0]) .............................................. Eqn. 5
ADC BLOCK: ANALOGUE-DIGITAL CONVERSION
The analogue signal is then converted to a 16-bit unsigned number, with input range configured by
PGAFS[1:0].
D1[15:0] = INT{ (V3 /VFS) ∗ 65535} + 32767 PGAFS[1:0] = 00 or 01 ...... Eqn. 6
D1[15:0] = INT{ (V3 /VFS) ∗ 65535}
PGAFS[1:0] = 11 ............... Eqn. 7
D1[15:0] = INT{ (V3 /VFS) ∗ 65535} + 65535 PGAFS[1:0] = 10 ............... Eqn. 8
where the ADC full-scale range, VFS = 3V
OUTPUT INVERT BLOCK: POLARITY ADJUST
The polarity of the digital output may be inverted by control bit INVOP.
D2[15:0] = D1[15:0]
(INVOP = 0) ...................... Eqn. 9
(INVOP = 1) ...................... Eqn. 10
D2[15:0] = 65535 – D1[15:0]
OUTPUT FORMATS
The digital data output from the ADC is available to the user in 8 or 4-bit wide multiplexed formats by
setting control bit MUXOP[1:0]. Latency of valid output data with respect to VSMP is programmable
by writing to control bits DEL[1:0]. The latency for each mode is shown in the Operating Mode Timing
Diagrams section.
Figure 15 shows the output data formats for Modes 1 – 2 and 4 – 6. Figure 16 shows the output data
formats for Mode 3. Table 2 summarises the output data obtained for each format.
MCLK
MCLK
8+8-BIT
OUTPUT
8+8-BIT
OUTPUT
A
B
A
B
4+4+4+4-BIT
OUTPUT
4+4+4+4-BIT
OUTPUT
A
B
C
D
A B A B C
D
Figure 15 Output Data Formats
Figure 16 Output Data Formats
(Mode 3)
(Modes 1 − 2, 4 − 6)
PD Rev 4.3 March 2007
17
w
WM8196
Production Data
OUTPUT
FORMAT
MUXOP[1:0]
00, 01, 10
11
OUTPUT
PINS
OUTPUT
8+8-bit
multiplexed
OP[7:0]
A = d15, d14, d13, d12, d11, d10, d9, d8
B = d7, d6, d5, d4, d3, d2, d1,d0
4+4+4+4-bit
(nibble)
OP[7:4]
A = d15, d14, d13, d12
B = d11, d10, d9, d8
C = d7, d6, d5, d4
D = d3, d2, d1, d0
Table 2 Details of Output Data Shown in Figure 15 and Figure 16.
CONTROL INTERFACE
The internal control registers are programmable via the serial digital control interface. The register
contents can be read back via the serial interface on pin OP[7]/SDO.
Note: It is recommended that a software reset is carried out after the power-up sequence, before
writing to any other register. This ensures that all registers are set to their default values (as shown
in Table 6).
SERIAL INTERFACE: REGISTER WRITE
Figure 17 shows register writing in serial mode. Three pins, SCK, SDI and SEN are used. A six-bit
address (a5, 0, a3, a2, a1, a0) is clocked in through SDI, MSB first, followed by an eight-bit data
word (b7, b6, b5, b4, b3, b2, b1, b0), also MSB first. Each bit is latched on the rising edge of SCK.
When the data has been shifted into the device, a pulse is applied to SEN to transfer the data to the
appropriate internal register. Note all valid registers have address bit a4 equal to 0 in write mode.
SCK
a5
0
a3
a2
a1
a0
b7
b6
b5
b4
b3
b2
b1
b0
SDI
Address
Data Word
SEN
Figure 17 Serial Interface Register Write
A software reset is carried out by writing to Address “000100” with any value of data, i.e. Data Word
= XXXXXXXX.
SERIAL INTERFACE: REGISTER READ-BACK
Figure 18 shows register read-back in serial mode. Read-back is initiated by writing to the serial bus
as described above but with address bit a4 set to 1, followed by an 8-bit dummy data word. Writing
address (a5, 1, a3, a2, a1, a0) will cause the contents (d7, d6, d5, d4, d3, d2, d1, d0) of
corresponding register (a5, 0, a3, a2, a1, a0) to be output MSB first on pin SDO (on the falling edge
of SCK). Note that pin SDO is shared with an output pin, OP[7], therefore OEB should always be
held low when register read-back data is expected on this pin. The next word may be read in to SDI
while the previous word is still being output on SDO.
PD Rev 4.3 March 2007
18
w
WM8196
Production Data
SCK
SDI
a5
1
a3 a2 a1 a0
x
x
x
x
x
x
x
x
Address
Data Word
SEN
SDO/
OP[7]
d7 d6 d5 d4 d3 d2 d1 d0
Output Data Word
OEB
Figure 18 Serial Interface Register Read-back
TIMING REQUIREMENTS
To use this device a master clock (MCLK) of up to 24MHz and a per-pixel synchronisation clock
(VSMP) of up to 12MHz are required. These clocks drive a timing control block, which produces
internal signals to control the sampling of the video signal. MCLK to VSMP ratios and maximum
sample rates for the various modes are shown in Table 5.
PROGRAMMABLE VSMP DETECT CIRCUIT
The VSMP input is used to determine the sampling point and frequency of the WM8196. Under
normal operation a pulse of 1 MCLK period should be applied to VSMP at the desired sampling
frequency (as shown in the Operating Mode Timing Diagrams) and the input sample will be taken on
the first rising MCLK edge after VSMP has gone low. However, in certain applications such a signal
may not be readily available. The programmable VSMP detect circuit in the WM8196 allows the
sampling point to be derived from any signal of the correct frequency, such as a CCD shift register
clock, when applied to the VSMP pin.
When enabled, by setting the VSMPDET control bit, the circuit detects either a rising or falling edge
(determined by POSNNEG control bit) on the VSMP input pin and generates an internal VSMP pulse.
This pulse can optionally be delayed by a number of MCLK periods, specified by the VDEL[2:0] bits.
Figure 19 shows the internal VSMP pulses that can be generated by this circuit for a typical clock
input signal. The internal VSMP pulse is then applied to the timing control block in place of the
normal VSMP pulse provided from the input pin. The sampling point then occurs on the first rising
MCLK edge after this internal VSMP pulse, as shown in the Operating Mode Timing Diagrams.
PD Rev 4.3 March 2007
19
w
WM8196
Production Data
MCLK
VSMP
INPUT
PINS
POSNNEG = 1
(VDEL = 000) INTVSMP
(VDEL = 001) INTVSMP
(VDEL = 010) INTVSMP
(VDEL = 011) INTVSMP
(VDEL = 100) INTVSMP
(VDEL = 101) INTVSMP
(VDEL = 110) INTVSMP
(VDEL = 111) INTVSMP
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
POSNNEG = 0
(VDEL = 000) INTVSMP
(VDEL = 001) INTVSMP
(VDEL = 010) INTVSMP
(VDEL = 011) INTVSMP
(VDEL = 100) INTVSMP
(VDEL = 101) INTVSMP
(VDEL = 110) INTVSMP
(VDEL = 111) INTVSMP
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
VS
Figure 19 Internal VSMP Pulses Generated by Programmable VSMP Detect Circuit
REFERENCES
The ADC reference voltages are derived from an internal bandgap reference, and buffered to pins
VRT and VRB, where they must be decoupled to ground. Pin VRX is driven by a similar buffer, and
also requires decoupling. The output buffer from the RLCDAC also requires decoupling at pin
VRLC/VBIAS
POWER SUPPLY
The WM8196 can run from a 5V single supply or from split 5V (core) and 3.3V (digital interface)
supplies.
POWER MANAGEMENT
Power management for the device is performed via the Control Interface. The device can be powered
on or off completely setting by the EN bit and SELPD bit low. Alternatively, when control bit SELPD is
high, only blocks selected by further control bits (SELDIS[3:0]) are powered down. This allows the
user to optimise power dissipation in certain modes, or to define an intermediate standby mode to
allow a quicker recovery into a fully active state. In Line-by-line operation, the green and blue channel
PGAs are automatically powered down.
All the internal registers maintain their previously programmed value in power down modes and the
Control Interface inputs remain active. Table 3 summarises the power down control bit functions.
EN
0
SELDPD
0
0
1
Device completely powers down.
1
Device completely powers up.
X
Blocks with respective SELDIS[3:0] bit high are disabled.
Table 3 Power Down Control
PD Rev 4.3 March 2007
20
w
WM8196
Production Data
LINE-BY-LINE OPERATION
Certain linear sensors (e.g. Contact Image Sensors) give colour output on a line-by-line basis. i.e. a
full line of red pixels followed by a line of green pixels followed by a line of blue pixels. In order to
accommodate this type of signal the WM8196 can be set into Monochrome mode, with the input
channel switched by writing to control bits CHAN[1:0] between every line. Alternatively, the WM8196
can be placed into colour line-by-line mode by setting the LINEBYLINE control bit. When this bit is
set the green and blue processing channels are powered down and the device is forced internally to
only operate in MONO mode (because only one colour is sampled at a time) through the red channel.
Figure 20 shows the signal path when operating in colour line-by-line mode.
VRLC/VBIAS
VSMP
MCLK
CL
RS VS TIMING CONTROL
R
8
OFFSET
MUX
OFFSET
DAC
G
B
16-
BIT
ADC
DATA
I/O
PORT
RINP
RLC
RLC
RLC
CDS
+
PGA
8
+
OP[7:0]
INPUT
MUX
R
I/P SIGNAL
POLARITY
ADJUST
PGA
MUX
G
GINP
BINP
B
SEN/STB
SCK/RNW
SDI/DNA
RLC/ACYC
NRESET
CONFIGURABLE
SERIAL/
PARALLEL
CONTROL
RLC
DAC
4
INTERFACE
Figure 20 Signal Path When in Line-by-Line Mode
In this mode the input multiplexer and (optionally) the PGA/Offset register multiplexers can be auto-
cycled by the application of pulses to the RLC/ACYC input pin by setting the ACYCNRLC register bit.
See Figure 4 for detailed timing information. The multiplexers change on the first MCLK rising edge
after RLC/ACYC is taken high. A write to the auto-cycle reset register causes these multiplexers to
be reset; selecting the RINP pin and the RED offset/gain registers. Alternatively, all three
multiplexers can be controlled via the serial interface by writing to register bits INTM[1:0] to select the
desired colour. It is also possible for the input multiplexer to be controlled separately from the PGA
and Offset multiplexers. Table 4 describes all the multiplexer selection modes that are possible.
FME ACYCNRLC
NAME
Internal,
no force mux
DESCRIPTION
0
0
1
0
1
0
Input mux, offset and gain registers determined by
internal register bits INTM1, INTM0.
Auto-cycling,
no force mux
Input mux, offset and gain registers auto-cycled, RINP
→ GINP → BINP → RINP… on RLC/ACYC pulse.
Input mux selected from internal register bits FM1, FM0;
Internal,
force mux
Offset and gain registers selected from internal register
bits INTM1, INTM0.
1
1
Auto-cycling,
force mux
Input mux selected from internal register bits FM1, FM0;
Offset and gain registers auto-cycled, RED → GREEN
→ BLUE → RED… on RLC/ACYC pulse.
Table 4 Colour Selection Description in Line-by-Line Mode
PD Rev 4.3 March 2007
21
w
WM8196
Production Data
OPERATING MODES
Table 5 summarises the most commonly used modes, the clock waveforms required and the register
contents required for CDS and non-CDS operation.
MODE
DESCRIPTION
CDS
AVAILABLE
MAX
SAMPLE
RATE
SENSOR
INTERFACE
DESCRIPTION
TIMING
REQUIRE-
MENTS
REGISTER
CONTENTS
WITH CDS
REGISTER
CONTENTS
WITHOUT CDS
1
Colour
Pixel-by-Pixel
Yes
4MSPS
The 3 input
channels are
sampled in
parallel. The
signal is then
gain and offset
adjusted before
being
MCLK max =
24MHz
SetReg1:
03(hex)
SetReg1: 01(hex)
MCLK: VSMP
ratio is 6:1
multiplexed into
a single data
stream and
converted by the
ADC, giving an
output data rate
of 12MSPS max.
2
3
Monochrome/
Colour
Line-by-Line
Yes
Yes
4MSPS
8MSPS
As mode 1
except:
Only one input
channel at a time
is continuously
sampled.
MCLK max =
24MHz
SetReg1:
07(hex)
SetReg1: 05(hex)
MCLK: VSMP
ratio is 6:1
Fast
Monochrome/
Colour
Identical to mode MCLK max =
2
Identical to
mode 2 plus
SetReg3:
bits 5:4 must
be set to
Identical to
mode 2
24MHz
MCLK: VSMP
ratio is 3:1
Line-by-Line
0(hex)
4
5
Maximum
speed
Monochrome/
Colour
No
12MSPS Identical to mode MCLK max =
CDS not
possible
SetReg1: 45(hex)
2
24MHz
MCLK: VSMP
ratio is 2:1
Line-by-Line
Slow Colour
Pixel-by-Pixel
Yes
3MSPS
3MPS
Identical to mode MCLK max =
Identical to
mode 1
Identical to
mode 1
1
24MHz
MCLK: VSMP
ratio is
2n:1, n ≥ 4
6
Slow
Monochrome/
Colour
Yes
Identical to mode MCLK max =
Identical to
mode 2
Identical to
mode 2
2
24MHz
MCLK: VSMP
ratio is
Line-by-Line
2n:1, n ≥ 4
Table 5 WM8196 Operating Modes
Notes:
1.
2.
In Monochrome mode, SetReg3 bits 7:6 determine which input is to be sampled.
For Colour Line-by-Line, set control bit LINEBYLINE. For input selection, refer to Table 4, Colour Selection
Description in Line-by-Line Mode.
PD Rev 4.3 March 2007
22
w
WM8196
Production Data
OPERATING MODE TIMING DIAGRAMS
The following diagrams show 8-bit multiplexed output data and MCLK, VSMP and input video
requirements for operation of the most commonly used modes as shown in Table 5. The diagrams
are identical for both CDS and non-CDS operation. Outputs from RINP, GINP and BINP are shown
as R, G and B respectively. X denotes invalid data.
16.5 MCLK PERIODS
MCLK
VSMP
INPUT VIDEO
OP[7:0]
(DEL = 00)
RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB
BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB
GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB GA GB BA BB RA RB
RA RB GA GB BA BB RA RB GA GB BA BB RA RB GB GA BA BB RA RB GA GB BA BB RA RB GA GB BA BB
OP[7:0]
(DEL = 01)
OP[7:0]
(DEL = 10)
OP[7:0]
(DEL = 11)
Figure 21 Mode 1 Operation
Figure 22 Mode 2 Operation
PD Rev 4.3 March 2007
23
w
WM8196
Production Data
Figure 23 Mode 3 Operation
Figure 24 Mode 4 Operation
PD Rev 4.3 March 2007
24
w
WM8196
Production Data
16.5 MCLK PERIODS
MCLK
VSMP
INPUT
VIDEO
OP[7:0]
RA RB GA GB BA BB
RA RB GA GB BA BB
RA RB GA GB BA BB
RA RB GA GB
X
X
X
X
X
X
X
X
(DEL = 00)
OP[7:0]
BA BB
RA RB GA GB BA BB
RA RB GA GB BA BB
RA RB GA GB BA BB
RA RB
X
X
X
X
X
X
X
X
(DEL = 01)
OP[7:0]
GA GB BA BB
RA RB GA GB BA BB
RA RB GA GB BA BB
RA RB GA GB BA BB
X
X
X
X
X
X
X
X
(DEL = 10)
OP[7:0]
RA RB GA GB BA BB
RA RB GA GB BA BB
RA RB GA GB BA BB
RA RB GA GB BA BB
X
X
X
X
X
X
(DEL = 11)
Figure 25 Mode 5 Operation (MCLK:VSMP Ratio = 8:1)
Figure 26 Mode 6 Operation (MCLK:VSMP Ratio = 8:1)
PD Rev 4.3 March 2007
25
w
WM8196
Production Data
DEVICE CONFIGURATION
REGISTER MAP
The following table describes the location of each control bit used to determine the operation of the
WM8196. The register map is programmed by writing the required codes to the appropriate
addresses via the serial interface.
ADDRESS
<a5:a0>
000001
000010
000011
000100
000101
000110
000111
001000
001001
001010
001011
001100
100000
100001
DESCRIPTION
DEF
(hex)
03
RW
BIT
b7
0
b6
b5
b4
PGAFS[0]
0
b3
b2
b1
b0
Setup Reg 1
Setup Reg 2
Setup Reg 3
Software Reset
Auto-cycle Reset
Setup Reg 4
Revision Number
Setup Reg 5
Setup Reg 6
Reserved
RW
RW
RW
W
MODE4
DEL[0]
PGAFS[1]
RLCDACRNG
CDSREF [1]
SELPD
MONO
INVOP
RLCV[2]
CDS
EN
20
DEL[1]
VRLCEXT
RLCV[3]
MUXOP[1]
RLCV[1]
MUXOP[0]
RLCV[0]
1F
00
CHAN[1] CHAN[0]
CDSREF [0]
00
W
00
RW
R
FM[1]
FM[0]
INTM[1]
INTM[0]
RLCINT
FME
ACYCNRLC
LINEBYLINE
41
00
RW
RW
RW
RW
RW
RW
RW
0
0
0
POSNNEG
VDEL[2]
VDEL[1]
VDEL[0]
VSMPDET
00
0
0
0
0
SELDIS[3]
SELDIS[2]
SELDIS[1]
SELDIS[0]
00
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Reserved
00
Reserved
00
0
0
0
0
0
0
0
0
DAC Value (Red)
80
DAC[7]
DAC[7]
DAC[6]
DAC[6]
DAC[5]
DAC[5]
DAC[4]
DAC[4]
DAC[3]
DAC[3]
DAC[2]
DAC[2]
DAC[1]
DAC[1]
DAC[0]
DAC[0]
DAC Value
(Green)
80
100010
100011
101000
101001
DAC Value (Blue)
DAC Value (RGB)
PGA Gain (Red)
80
80
00
00
RW
W
DAC[7]
DAC[7]
PGA[7]
PGA[7]
DAC[6]
DAC[6]
PGA[6]
PGA[6]
DAC[5]
DAC[5]
PGA[5]
PGA[5]
DAC[4]
DAC[4]
PGA[4]
PGA[4]
DAC[3]
DAC[3]
PGA[3]
PGA[3]
DAC[2]
DAC[2]
PGA[2]
PGA[2]
DAC[1]
DAC[1]
PGA[1]
PGA[1]
DAC[0]
DAC[0]
PGA[0]
PGA[0]
RW
RW
PGA Gain
(Green)
101010
101011
PGA Gain (Blue)
PGA Gain (RGB)
00
00
RW
W
PGA[7]
PGA[7]
PGA[6]
PGA[6]
PGA[5]
PGA[5]
PGA[4]
PGA[4]
PGA[3]
PGA[3]
PGA[2]
PGA[2]
PGA[1]
PGA[1]
PGA[0]
PGA[0]
Table 6 Register Map
PD Rev 4.3 March 2007
26
w
WM8196
Production Data
REGISTER MAP DESCRIPTION
The following table describes the function of each of the control bits shown in Table 6.
REGISTER
BIT
NO
BIT
NAME(S)
DEFAULT
DESCRIPTION
Setup
0
EN
1
When SELPD = 1 this bit has no effect.
Register 1
When SELPD = 0 this bit controls the global power down:
0 = complete power down, 1 = fully active.
1
CDS
1
Select correlated double sampling mode: 0 = single ended mode,
1 = CDS mode.
2
3
MONO
SELPD
0
0
Mono/colour select: 0 = colour, 1 = monochrome operation.
Selective power down: 0 = no individual control,
1 = individual blocks can be disabled (controlled by SELDIS[3:0]).
5:4
PGAFS[1:0]
00
Offsets PGA output to optimise the ADC range for different polarity sensor
output signals. Zero differential PGA input signal gives:
00 = Zero output
(use for bipolar video)
01 = Zero output
10 = Full-scale positive output
(use for negative going video)
11 = Full-scale negative output
(use for positive going video)
6
7
MODE4
Reserved
0
0
Required when operating in MODE4: 0 = other modes, 1 = MODE4.
Must be set to zero
Setup
1:0
MUXOP[1:0]
00
Determines the output data format.
Register 2
00 = 16-bit parallel
10 = 8-bit multiplexed mode (8+8 bits)
01 = 8-bit multiplexed (8+8 bits) 11 = 4-bit multiplexed mode (4+4+4+4 bits)
2
INVOP
0
Digitally inverts the polarity of output data.
0 = negative going video gives negative going output,
1 = negative-going video gives positive going output data.
3
5
VRLCEXT
0
1
When set powers down the RLCDAC, changing its output to Hi-Z, allowing
VRLC/VBIAS to be externally driven.
RLCDACRNG
Sets the output range of the RLCDAC.
0 = RLCDAC ranges from 0 to AVDD (approximately),
1 = RLCDAC ranges from 0 to VRT (approximately).
7:6
DEL[1:0]
00
Sets the output latency in ADC clock periods.
1 ADC clock period = 2 MCLK periods except in Mode 3 where 1 ADC clock
period = 3 MCLK periods.
00 = Minimum latency
01 = Delay by one ADC clock
period
10 = Delay by two ADC clock periods
11 = Delay by three ADC clock periods
Setup
Register 3
3:0
5:4
RLCV[3:0]
1111
01
Controls RLCDAC driving VRLC pin to define single ended signal reference
voltage or Reset Level Clamp voltage. See Electrical Characteristics section
for ranges.
CDSREF[1:0]
CDS mode reset timing adjust.
00 = Advance 1 MCLK period
01 = Normal
10 = Retard 1 MCLK period
11 = Retard 2 MCLK periods
7:6
CHAN[1:0]
00
Monochrome mode channel select.
00 = Red channel select
01 = Green channel select
10 = Blue channel select
11 = Reserved
Software
Reset
Any write to Software Reset causes all cells to be reset. It is recommended
that a software reset be performed after a power-up before any other register
writes.
Auto-cycle
Reset
Any write to Auto-cycle Reset causes the auto-cycle counter to reset
to RINP. This function is only required when LINEBYLINE = 1.
PD Rev 4.3 March 2007
27
w
WM8196
Production Data
REGISTER
BIT
NO
BIT
NAME(S)
DEFAULT
DESCRIPTION
Setup
Register 4
0
LINEBYLINE
0
Selects line by line operation 0 = normal operation,
1 = line by line operation.
When line by line operation is selected MONO is forced to 1 and CHAN[1:0] to
00 internally, ensuring that the correct internal timing signals are produced.
Green and Blue PGAs are also disabled to save power.
1
ACYCNRLC
0
When LINEBYLINE = 0 this bit has no effect.
When LINEBYLINE = 1 this bit determines the function of the RLC/ACYC
input pin and the input multiplexer and offset/gain register controls.
0 = RLC/ACYC pin enabled for Reset Level Clamp. Internal selection of input
and gain/offset multiplexers,
1 = Auto-cycling enabled by pulsing the RLC/ACYC input pin.
See Table 4, Colour Selection Description in Line-by-Line Mode for colour
selection mode details.
When auto-cycling is enabled, the RLC/ACYC pin cannot be used for reset
level clamping. The RLCINT bit may be used instead.
2
FME
0
When LINEBYLINE = 0 this bit has no effect.
When LINEBYLINE = 1 this bit controls the input force mux mode:
0 = No force mux, 1 = Force mux mode. Forces the input mux to be selected
by FM[1:0] separately from gain and offset multiplexers.
See Table 4 for details.
3
RLCINT
0
When LINEBYLINE = 1 and ACYCNRLC = 1 this bit is used to determine
whether Reset Level Clamping is used.
0 = RLC disabled, 1 = RLC enabled.
5:4
INTM[1:0]
00
Colour selection bits used in internal modes.
00 = Red, 01 = Green, 10 = Blue and 11 = Reserved.
See Table 4 for details.
7:6
0
FM[1:0]
00
0
Colour selection bits used in input force mux modes.
00 = RINP, 01 = GINP, 10 = BINP and 11 = Reserved.
See Table 4 for details.
Setup
Register 5
VSMPDET
0 = Normal operation, signal on VSMP input pin is applied directly to Timing
Control block.
1 = Programmable VSMP detect circuit is enabled. An internal synchronisation
pulse is generated from signal applied to VSMP input pin and is applied to
Timing Control block.
3:1
VDEL[2:0]
000
When VSMPDET = 0 these bits have no effect.
When VSMPDET = 1 these bits set a programmable delay from the detected
edge of the signal applied to the VSMP pin. The internally generated pulse is
delayed by VDEL MCLK periods from the detected edge.
See Figure 19, Internal VSMP Pulses Generated for details.
4
POSNNEG
0
When VSMPDET = 0 this bit has no effect.
When VSMPDET = 1 this bit controls whether positive or negative edges
are detected:
0 = Negative edge on VSMP pin is detected and used to generate internal
timing pulse.
1 = Positive edge on VSMP pin is detected and used to generate internal
timing pulse.
See Figure 19 for further details.
7:5
3:0
Reserved
000
Must be set to zero
Setup
Register 6
SELDIS[3:0]
0000
Selective power disable register - activated when SELPD = 1.
Each bit disables respective cell when 1, enabled when 0.
SELDIS[0] = Red CDS, PGA
SELDIS[1] = Green CDS, PGA
SELDIS[2] = Blue CDS, PGA
SELDIS[3] = ADC
7:4
Reserved
0000
Must be set to zero
PD Rev 4.3 March 2007
28
w
WM8196
Production Data
REGISTER
BIT
NO
BIT
NAME(S)
DEFAULT
DESCRIPTION
Offset DAC
(Red)
7:0
DAC[7:0]
10000000
Red channel offset DAC value.
Offset DAC
(Green)
7:0
7:0
7:0
DAC[7:0]
DAC[7:0]
DAC[7:0]
10000000
10000000
10000000
Green channel offset DAC value
Blue channel offset DAC value
Offset DAC
(Blue)
Offset DAC
(RGB)
A write to this register location causes the red, green and blue offset DAC
registers to be overwritten by the new value
PGA gain
(Red)
7:0
7:0
7:0
7:0
PGA[7:0]
PGA[7:0]
PGA[7:0]
PGA[7:0]
00000000
00000000
00000000
00000000
Determines the gain of the red channel PGA according to the equation:
Red channel PGA gain = 208/(283-PGA[7:0])
PGA gain
(Green)
Determines the gain of the green channel PGA according to the equation:
Green channel PGA gain = 208/(283-PGA[7:0])
PGA gain
(Blue)
Determines the gain of the blue channel PGA according to the equation:
Blue channel PGA gain = 208/(283-PGA[7:0])
PGA gain
(RGB)
A write to this register location causes the red, green and blue PGA gain
registers to be overwritten by the new value
Table 7 Register Control Bits
PD Rev 4.3 March 2007
29
w
WM8196
Production Data
APPLICATIONS INFORMATION
RECOMMENDED EXTERNAL COMPONENTS
DVDD2
DVDD1
3
8
DVDD1
DVDD2
DGND
10
C1
C2
AVDD
21
22
2
AVDD
AGND1
AGND2
C3
DGND
AGND
AGND
24
25
23
VRT
VRX
VRB
1
RINP
GINP
BINP
C4
C5
Video
Inputs
28
27
C6
C7
C8
26
VRLC/VBIAS
C9
AGND
WM8196
AGND
20
19
18
17
16
15
14
13
OP[7]/SDO
DVDD1 DVDD2
AVDD
7
5
6
MCLK
OP[6]
Timing
Signals
VSMP
OP[5]
C10
C11
C12
+
+
+
Output
Data
Bus
RLC/ACYC
OP[4]
OP[3]
12
11
9
SCK
SDI
OP[2]
DGND
AGND
OP[1]
SEN
OP[0]
Interface
Controls
4
OEB
NOTES: 1. C1-9 should be fitted as close to WM8196 as possible.
2. AGND and DGND should be connected as close to WM8196 as possible.
Figure 26 External Components Diagram
RECOMMENDED EXTERNAL COMPONENT VALUE
COMPONENT
REFERENCE
SUGGESTED VALUE
DESCRIPTION
C1
C2
100nF
100nF
100nF
10nF
De-coupling for DVDD1.
De-coupling for DVDD2.
De-coupling for AVDD.
C3
C4
High frequency de-coupling between VRT and VRB.
C5
1µF
Low frequency de-coupling between VRT and VRB (non-polarised).
De-coupling for VRB.
C6
100nF
100nF
100nF
100nF
10µF
C7
De-coupling for VRX.
C8
De-coupling for VRT.
C9
De-coupling for VRLC.
C10
C11
C12
Reservoir capacitor for DVDD1.
Reservoir capacitor for DVDD2.
Reservoir capacitor for AVDD.
10µF
10µF
Table 8 External Components Descriptions
PD Rev 4.3 March 2007
30
w
WM8196
Production Data
PACKAGE DIMENSIONS
DS: 28 PIN SSOP (10.2 x 5.3 x 1.75 mm)
DM007.E
b
e
28
15
E1
E
GAUGE
PLANE
Θ
14
1
D
0.25
L
c
A1
L1
A A2
-C-
0.10 C
SEATING PLANE
Dimensions
(mm)
NOM
-----
Symbols
MIN
-----
0.05
1.65
0.22
0.09
9.90
MAX
A
A1
A2
b
c
D
e
E
E1
L
2.0
0.25
1.85
0.38
0.25
10.50
-----
1.75
0.30
-----
10.20
0.65 BSC
7.80
7.40
5.00
0.55
8.20
5.60
0.95
5.30
0.75
L1
θ
1.25 REF
0o
4o
8o
JEDEC.95, MO-150
REF:
NOTES:
A. ALL LINEAR DIMENSIONS ARE IN MILLIMETERS.
B. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE.
C. BODY DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSION, NOT TO EXCEED 0.20MM.
D. MEETS JEDEC.95 MO-150, VARIATION = AH. REFER TO THIS SPECIFICATION FOR FURTHER DETAILS.
PD Rev 4.3 March 2007
31
w
WM8196
Production Data
IMPORTANT NOTICE
Wolfson Microelectronics plc (“Wolfson”) products and services are sold subject to Wolfson’s terms and conditions of sale,
delivery and payment supplied at the time of order acknowledgement.
Wolfson warrants performance of its products to the specifications in effect at the date of shipment. Wolfson reserves the
right to make changes to its products and specifications or to discontinue any product or service without notice. Customers
should therefore obtain the latest version of relevant information from Wolfson to verify that the information is current.
Testing and other quality control techniques are utilised to the extent Wolfson deems necessary to support its warranty.
Specific testing of all parameters of each device is not necessarily performed unless required by law or regulation.
In order to minimise risks associated with customer applications, the customer must use adequate design and operating
safeguards to minimise inherent or procedural hazards. Wolfson is not liable for applications assistance or customer
product design. The customer is solely responsible for its selection and use of Wolfson products. Wolfson is not liable for
such selection or use nor for use of any circuitry other than circuitry entirely embodied in a Wolfson product.
Wolfson’s products are not intended for use in life support systems, appliances, nuclear systems or systems where
malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage.
Any use of products by the customer for such purposes is at the customer’s own risk.
Wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other
intellectual property right of Wolfson covering or relating to any combination, machine, or process in which its products or
services might be or are used. Any provision or publication of any third party’s products or services does not constitute
Wolfson’s approval, licence, warranty or endorsement thereof. Any third party trade marks contained in this document
belong to the respective third party owner.
Reproduction of information from Wolfson datasheets is permissible only if reproduction is without alteration and is
accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. Wolfson is
not liable for any unauthorised alteration of such information or for any reliance placed thereon.
Any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in
this datasheet or in Wolfson’s standard terms and conditions of sale, delivery and payment are made, given and/or
accepted at that person’s own risk. Wolfson is not liable for any such representations, warranties or liabilities or for any
reliance placed thereon by any person.
ADDRESS:
Wolfson Microelectronics plc
Westfield House
26 Westfield Road
Edinburgh
EH11 2QB
United Kingdom
Tel :: +44 (0)131 272 7000
Fax :: +44 (0)131 272 7001
Email :: sales@wolfsonmicro.com
PD Rev 4.3 March 2007
32
w
相关型号：
©2020 ICPDF网 联系我们和版权申明