W25Q64JVSSIQ [WINBOND]
3V 64M-bit serial flash memory with dualm quad spi;型号: | W25Q64JVSSIQ |
厂家: | WINBOND |
描述: | 3V 64M-bit serial flash memory with dualm quad spi |
文件: | 总77页 (文件大小:2879K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
W25Q64JV
3V 64M-BIT
SERIAL FLASH MEMORY WITH
DUAL, QUAD SPI
Publication Release Date: June 03, 2016
Revision C
W25Q64JV
Table of Contents
1.
2.
3.
GENERAL DESCRIPTIONS..................................................................................................................4
FEATURES............................................................................................................................................4
PACKAGE TYPES AND PIN CONFIGURATIONS ...............................................................................5
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Pin Configuration SOIC 208-mil / VSOP 208-mil ......................................................................5
Pad Configuration WSON 6x5-mm/ 8x6-mm, XSON 4x4-mm..................................................5
Pin Description SOIC / VSOP 208-mil, WSON 6x5-mm/ 8x6-mm, XSON 4x4-mm..................5
Pin Configuration SOIC 300-mil ................................................................................................6
Pin Description SOIC 300-mil....................................................................................................6
Pin Configuration PDIP 300-mil.................................................................................................7
Pin Description PDIP 300-mil....................................................................................................7
Ball Configuration TFBGA 8x6-mm (6x4 Ball Array) .................................................................8
Ball Description TFBGA 8x6-mm ..............................................................................................8
4.
PIN DESCRIPTIONS.............................................................................................................................9
4.1
4.2
4.3
4.4
Chip Select (/CS).......................................................................................................................9
Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3) .........................................9
Serial Clock (CLK).....................................................................................................................9
Reset (/RESET)(1)......................................................................................................................9
5.
6.
BLOCK DIAGRAM...............................................................................................................................10
FUNCTIONAL DESCRIPTIONS..........................................................................................................11
6.1
6.2
6.3
6.4
6.5
Standard SPI Instructions........................................................................................................11
Dual SPI Instructions...............................................................................................................11
Quad SPI Instructions..............................................................................................................11
Software Reset & Hardware /RESET pin................................................................................11
Write Protection.......................................................................................................................12
Write Protect Features...............................................................................................................12
7.
STATUS AND CONFIGURATION REGISTERS.................................................................................13
7.1
Status Registers ......................................................................................................................13
Erase/Write In Progress (BUSY) – Status Only......................................................................13
Write Enable Latch (WEL) – Status Only................................................................................13
Block Protect Bits (BP2, BP1, BP0) – Volatile/Non-Volatile Writable......................................13
Top/Bottom Block Protect (TB) – Volatile/Non-Volatile Writable.............................................14
Sector/Block Protect Bit (SEC) – Volatile/Non-Volatile Writable.............................................14
Complement Protect (CMP) – Volatile/Non-Volatile Writable .................................................14
Status Register Protect (SRP, SRL) ..........................................................................................15
Erase/Program Suspend Status (SUS) – Status Only ............................................................15
Security Register Lock Bits (LB3, LB2, LB1) – Volatile/Non-Volatile OTP Writable................15
Quad Enable (QE) – Volatile/Non-Volatile Writable..............................................................16
Write Protect Selection (WPS) – Volatile/Non-Volatile Writable ...........................................16
Output Driver Strength (DRV1, DRV0) – Volatile/Non-Volatile Writable ...............................16
Reserved Bits – Non Functional ...........................................................................................16
Status Register Memory Protection (WPS = 0, CMP = 0)........................................................17
Publication Release Date: June 03, 2016
- 1 -
Revision C
W25Q64JV
Status Register Memory Protection (WPS = 0, CMP = 1)........................................................18
Individual Block Memory Protection (WPS=1) .........................................................................19
8.
INSTRUCTIONS..................................................................................................................................20
8.1
Device ID and Instruction Set Tables......................................................................................20
Manufacturer and Device Identification......................................................................................20
Instruction Set Table 1 (Standard SPI Instructions)(1) ................................................................21
Instruction Set Table 2 (Dual/Quad SPI Instructions)(1)..............................................................22
Instruction Descriptions ...........................................................................................................23
Write Enable (06h).....................................................................................................................23
Write Enable for Volatile Status Register (50h)..........................................................................23
Write Disable (04h)....................................................................................................................24
Read Status Register-1 (05h), Status Register-2 (35h) & Status Register-3 (15h)....................24
Write Status Register-1 (01h), Status Register-2 (31h) & Status Register-3 (11h) ....................25
Read Data (03h) ........................................................................................................................27
Fast Read (0Bh) ........................................................................................................................28
Fast Read Dual Output (3Bh) ....................................................................................................29
Fast Read Quad Output (6Bh)...................................................................................................30
Fast Read Dual I/O (BBh)........................................................................................................31
Fast Read Quad I/O (EBh).......................................................................................................32
Set Burst with Wrap (77h)........................................................................................................33
Page Program (02h) ................................................................................................................34
Quad Input Page Program (32h)..............................................................................................35
Sector Erase (20h) ..................................................................................................................36
32KB Block Erase (52h).............................................................................................................37
64KB Block Erase (D8h)............................................................................................................38
Chip Erase (C7h / 60h)..............................................................................................................39
Erase / Program Suspend (75h) ................................................................................................40
Erase / Program Resume (7Ah).................................................................................................41
Power-down (B9h) .....................................................................................................................42
Release Power-down / Device ID (ABh)....................................................................................43
Read Manufacturer / Device ID (90h) ........................................................................................44
Read Manufacturer / Device ID Dual I/O (92h) ..........................................................................45
Read Manufacturer / Device ID Quad I/O (94h).......................................................................46
Read Unique ID Number (4Bh)................................................................................................47
Read JEDEC ID (9Fh) .............................................................................................................48
Read SFDP Register (5Ah)......................................................................................................49
Erase Security Registers (44h)................................................................................................50
Program Security Registers (42h)............................................................................................51
Read Security Registers (48h).................................................................................................52
Individual Block/Sector Lock (36h)...........................................................................................53
Individual Block/Sector Unlock (39h) .......................................................................................54
Read Block/Sector Lock (3Dh).................................................................................................55
Global Block/Sector Lock (7Eh)...............................................................................................56
Global Block/Sector Unlock (98h)............................................................................................56
Enable Reset (66h) and Reset Device (99h) ...........................................................................57
8.2
8.3
Publication Release Date: June 03, 2016
- 2 -
Revision C
W25Q64JV
9.
ELECTRICAL CHARACTERISTICS....................................................................................................58
(1)
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
Absolute Maximum Ratings
...............................................................................................58
Operating Ranges ...................................................................................................................58
Power-Up Power-Down Timing and Requirements ................................................................59
DC Electrical Characteristics-..................................................................................................60
AC Measurement Conditions ..................................................................................................61
AC Electrical Characteristics(6) ................................................................................................62
Serial Output Timing................................................................................................................64
Serial Input Timing...................................................................................................................64
10.
PACKAGE SPECIFICATIONS ............................................................................................................65
10.1 8-Pin SOIC 208-mil (Package Code SS).................................................................................65
10.2 8-Pin VSOP 208-mil (Package Code ST)................................................................................66
10.3 8-Pad WSON 6x5-mm (Package Code ZP)............................................................................67
10.4 8-Pad WSON 8x6mm (Package Code ZE) .............................................................................68
10.5 8-Pad XSON 4x4x0.45-mm (Package Code XG) ...................................................................69
10.6 16-Pin SOIC 300-mil (Package Code SF)...............................................................................70
10.8 8-Pin PDIP 300-mil (Package Code DA).................................................................................71
10.10 24-Ball TFBGA 8x6-mm (Package Code TB, 5x5 Ball Array) ...............................................72
10.11 24-Ball TFBGA 8x6-mm (Package Code TC, 6x4 ball array) ................................................73
ORDERING INFORMATION ...............................................................................................................74
11.1 Valid Part Numbers and Top Side Marking.............................................................................75
REVISION HISTORY...........................................................................................................................76
11.
12.
Publication Release Date: June 03, 2016
- 3 -
Revision C
W25Q64JV
1. GENERAL DESCRIPTIONS
The W25Q64JV (64M-bit) Serial Flash memory provides a storage solution for systems with limited space,
pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices.
They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP) and storing
voice, text and data. The device operates on 2.7V to 3.6V power supply with current consumption as low as
1µA for power-down. All devices are offered in space-saving packages.
The W25Q64JV array is organized into 32,768 programmable pages of 256-bytes each. Up to 256 bytes can
be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128 (32KB
block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q64JV has 2,048
erasable sectors and 128 erasable blocks respectively. The small 4KB sectors allow for greater flexibility in
applications that require data and parameter storage. (See Figure 2.)
The W25Q64JV supports the standard Serial Peripheral Interface (SPI), Dual/Quad I/O SPI: Serial Clock, Chip
Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 and I/O3. SPI clock frequencies of W25Q64JV of up to 133MHz
are supported allowing equivalent clock rates of 266MHz (133MHz x 2) for Dual I/O and 532MHz (133MHz x
4) for Quad I/O when using the Fast Read Dual/Quad I/O. These transfer rates can outperform standard
Asynchronous 8 and 16-bit Parallel Flash memories.
Additionally, the device supports JEDEC standard manufacturer and device ID, and a 64-bit Unique Serial
Number and three 256-bytes Security Registers.
2. FEATURES
New Family of SpiFlash Memories
– W25Q64JV: 64M-bit / 8M-byte
– Standard SPI: CLK, /CS, DI, DO
– Dual SPI: CLK, /CS, IO0, IO1
Flexible Architecture with 4KB sectors
– Uniform Sector/Block Erase (4K/32K/64K-Byte)
– Program 1 to 256 byte per programmable page
– Erase/Program Suspend & Resume
Advanced Security Features
– Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3
– Software & Hardware Reset(1)
– Software and Hardware Write-Protect
– Special OTP protection(1)
– Top/Bottom, Complement array protection
– Individual Block/Sector array protection
– 64-Bit Unique ID for each device
– Discoverable Parameters (SFDP) Register
– 3X256-Bytes Security Registers
Highest Performance Serial Flash
– More than 100,000 erase/program cycles
– Min. 100K Program-Erase cycles per sector
– 133MHz Single, Dual/Quad SPI clocks
266/532MHz equivalent Dual/Quad SPI
– Volatile & Non-volatile Status Register Bits
Space Efficient Packaging
– 8-pin SOIC 208-mil / VSOP 208-mil
– 8-pad WSON 6x5-mm/8x6-mm, XSON 4x4-mm
– 16-pin SOIC 300-mil
Efficient “Continuous Read”
– Continuous Read with 8/16/32/64-Byte Wrap
– As few as 8 clocks to address memory
– Allows true XIP (execute in place) operation
– Outperforms X16 Parallel Flash
Low Power, Wide Temperature Range
– Single 2.7 to 3.6V supply
– 8-pin PDIP 300-mil
– 24-ball TFBGA 8x6-mm (6x4 ball array)
– 24-ball TFBGA 8x6-mm (6x4/5x5 ball array)
– Contact Winbond for KGD and other options
– <1µA Power-down (typ.)
– -40°C to +85°C operating range
Note: 1. Hardware /RESET pin is only available on TFBGA packages
Publication Release Date: June 03, 2016
Revision C
- 4 -
W25Q64JV
3. PACKAGE TYPES AND PIN CONFIGURATIONS
3.1 Pin Configuration SOIC 208-mil / VSOP 208-mil
Top View
/CS
1
2
3
4
8
7
6
5
VCC
IO3
DO (IO1)
IO2
CLK
GND
DI (IO0)
Figure 1a. W25Q64JV Pin Assignments, 8-pin SOIC / VSOP 208-mil (Package Code SS / ST)
3.2 Pad Configuration WSON 6x5-mm/ 8x6-mm, XSON 4x4-mm
Figure 1b. W25Q64JV Pad Assignments, 8-pad WSON 6x5-mm/8x6 (Package Code ZP, ZE, XG)
3.3 Pin Description SOIC / VSOP 208-mil, WSON 6x5-mm/ 8x6-mm, XSON 4x4-mm
PAD NO.
PAD NAME
/CS
I/O
I
FUNCTION
1
2
3
4
5
6
7
8
Chip Select Input
DO (IO1)
IO2
I/O
I/O
Data Output (Data Input Output 1)(1)
Data Input Output 2(2)
Ground
GND
DI (IO0)
CLK
I/O
I
Data Input (Data Input Output 0)(1)
Serial Clock Input
IO3
I/O
Data Input Output 3(2)
Power Supply
VCC
Notes:
1. IO0 and IO1 are used for Standard and Dual SPI instructions
2. IO0 – IO3 are used for Quad SPI instructions (factory default for Quad Enabled part numbers with ordering option “IQ”)
Publication Release Date: June 03, 2016
- 5 -
Revision C
W25Q64JV
3.4 Pin Configuration SOIC 300-mil
Top View
IO3
VCC
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
CLK
DI (IO0)
NC
/RESET
NC
NC
NC
NC
NC
NC
/CS
GND
IO2
DO (IO1)
Figure 1c. W25Q64JV Pin Assignments, 16-pin SOIC 300-mil (Package Code SF)
3.5 Pin Description SOIC 300-mil
PIN NO.
PIN NAME
IO3
I/O
FUNCTION
1
2
I/O
Data Input Output 3(2)
Power Supply
Reset Input(3)
No Connect
VCC
3
/RESET
N/C
I
4
5
N/C
No Connect
6
N/C
No Connect
7
/CS
I
Chip Select Input
8
DO (IO1)
IO2
I/O
I/O
Data Output (Data Input Output 1)(1)
Data Input Output 2(2)
Ground
9
10
11
12
13
14
15
16
GND
N/C
No Connect
N/C
No Connect
N/C
No Connect
N/C
No Connect
DI (IO0)
CLK
I/O
I
Data Input (Data Input Output 0)(1)
Serial Clock Input
Notes:
1. IO0 and IO1 are used for Standard and Dual SPI instructions
2. IO0 – IO3 are used for Quad SPI instructions.
3. . The /RESET pin is a dedicated hardware reset pin regardless of device settings or operation states. If the hardware reset function is
not used, this pin can be left floating or connected to VCC in the system.
Publication Release Date: June 03, 2016
- 6 -
Revision C
W25Q64JV
3.6 Pin Configuration PDIP 300-mil
Top View
/CS
1
2
3
4
8
7
6
5
VCC
IO3
DO(IO1)
IO2
CLK
GND
DI(IO)
Figure 1e. W25Q64JV Pin Assignments, 8-pin PDIP (Package Code DA)
3.7 Pin Description PDIP 300-mil
PAD NO.
PAD NAME
/CS
I/O
I
FUNCTION
1
2
3
4
5
6
7
8
Chip Select Input
DO (IO1)
IO2
I/O
I/O
Data Output (Data Input Output 1)(1)
Data Input Output 2(2)
Ground
GND
DI (IO0)
CLK
I/O
I
Data Input (Data Input Output 0)(1)
Serial Clock Input
IO3
I/O
Data Input Output 3(2)
Power Supply
VCC
Notes:
1. IO0 and IO1 are used for Standard and Dual SPI instructions
2. IO0 – IO3 are used for Quad SPI instructions (factory default for Quad Enabled part numbers with ordering option “IQ”).
Publication Release Date: June 03, 2016
- 7 -
Revision C
W25Q64JV
3.8 Ball Configuration TFBGA 8x6-mm (6x4 Ball Array)
Figure 1d. W25Q64JV Ball Assignments, 24-ball TFBGA 8x6-mm (Package Code TB/TC)
3.9 Ball Description TFBGA 8x6-mm
BALL NO.
PIN NAME
/RESET
CLK
I/O
FUNCTION
A4
B2
I
I
Reset Input(3)
Serial Clock Input
Ground
B3
GND
B4
VCC
Power Supply
Chip Select Input
Data Input Output 2(2)
C2
/CS
I
C4
IO2
I/O
I/O
I/O
I/O
D2
DO (IO1)
DI (IO0)
IO3
Data Output (Data Input Output 1)(1)
Data Input (Data Input Output 0)(1)
Data Input Output 3(2)
D3
D4
Multiple
NC
No Connect
Notes:
1. IO0 and IO1 are used for Standard and Dual SPI instructions
2. IO0 – IO3 are used for Quad SPI instructions (factory default for Quad Enabled part numbers with ordering option “IQ”).
3. The /RESET pin is a dedicated hardware reset pin regardless of device settings or operation states. If the hardware reset function is
not used, this pin can be left floating or connected to VCC in the system
Publication Release Date: June 03, 2016
- 8 -
Revision C
W25Q64JV
4. PIN DESCRIPTIONS
4.1 Chip Select (/CS)
The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high the device is
deselected and the Serial Data Output (DO, or IO0, IO1, IO2, IO3) pins are at high impedance. When
deselected, the devices power consumption will be at standby levels unless an internal erase, program or write
status register cycle is in progress. When /CS is brought low the device will be selected, power consumption
will increase to active levels and instructions can be written to and data read from the device. After power-up,
/CS must transition from high to low before a new instruction will be accepted. The /CS input must track the
VCC supply level at power-up and power-down (see “Write Protection” and Figure 58). If needed a pull-up
resister on the /CS pin can be used to accomplish this.
4.2 Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3)
The W25Q64JV supports Standard SPI, Dual SPI and Quad SPI operation in each individual stacked die. All
8-bit instructions are shifted into the device through DI (IO0) pin, address and data are shifted in and out of
the device through either DI & DO pins for Standard SPI instructions, IO0 & IO1 pins for Dual SPI instructions,
or IO0-IO3 pins for Quad SPI instructions.
4.3 Serial Clock (CLK)
The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See SPI
Operations")
4.4 Reset (/RESET)(1)
A dedicated hardware /RESET pin is available on SOIC-16 and TFBGA packages. When it’s driven low for a
minimum period of ~1µS, this device will terminate any external or internal operations and return to its power-
on state.
Note:
1. Hardware /RESET pin is available on SOIC-16 or TFBGA; please contact Winbond for this package.
Publication Release Date: June 03, 2016
- 9 -
Revision C
W25Q64JV
5. BLOCK DIAGRAM
SFDP Register
Security Register 1-3
Block Segmentation
xxFF00h
•
xxF000h
xxFFFFh
•
xxF0FFh
Sector 15 (4KB)
Sector 14 (4KB)
Sector 13 (4KB)
xxEF00h
•
xxE000h
xxEFFFh
•
xxE0FFh
xxDF00h
•
xxDFFFh
•
xxD000h
xxD0FFh
•
•
•
xx2F00h
•
xx2000h
xx2FFFh
•
xx20FFh
Sector 2 (4KB)
Sector 1 (4KB)
Sector 0 (4KB)
xx1F00h
•
xx1000h
xx1FFFh
•
xx10FFh
xx0F00h
•
xx0FFFh
•
xx0000h
xx00FFh
Status
Register
High Voltage
Generators
CLK
Page Address
Latch / Counter
/CS
Beginning
Page Address
Ending
Page Address
SPI
Command &
Control Logic
DI (IO0)
Column Decode
And 256 -Byte Page Buffer
DO (IO1)
(IO2)
Data
(IO3)
Byte Address
Latch / Counter
Figure 2. W25Q64JV Serial Flash Memory Block Diagram
Publication Release Date: June 03, 2016
Revision C
- 10 -
W25Q64JV
6. FUNCTIONAL DESCRIPTIONS
6.1 Standard SPI Instructions
The W25Q64JV is accessed through an SPI compatible bus consisting of four signals: Serial Clock (CLK),
Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions use the DI
input pin to serially write instructions, addresses or data to the device on the rising edge of CLK. The DO
output pin is used to read data or status from the device on the falling edge of CLK.
SPI bus operation Mode 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0 and Mode
3 concerns the normal state of the CLK signal when the SPI bus master is in standby and data is not being
transferred to the Serial Flash. For Mode 0, the CLK signal is normally low on the falling and rising edges of
/CS. For Mode 3, the CLK signal is normally high on the falling and rising edges of /CS.
6.2 Dual SPI Instructions
The W25Q64JV supports Dual SPI operation when using instructions such as “Fast Read Dual Output (3Bh)”
and “Fast Read Dual I/O (BBh)”. These instructions allow data to be transferred to or from the device at two
to three times the rate of ordinary Serial Flash devices. The Dual SPI Read instructions are ideal for quickly
downloading code to RAM upon power-up (code-shadowing) or for executing non-speed-critical code directly
from the SPI bus (XIP). When using Dual SPI instructions, the DI and DO pins become bidirectional I/O pins:
IO0 and IO1.
6.3 Quad SPI Instructions
The W25Q64JV supports Quad SPI operation when using instructions such as “Fast Read Quad Output
(6Bh)”, and “Fast Read Quad I/O (EBh). These instructions allow data to be transferred to or from the device
four to six times the rate of ordinary Serial Flash. The Quad Read instructions offer a significant improvement
in continuous and random access transfer rates allowing fast code-shadowing to RAM or execution directly
from the SPI bus (XIP). When using Quad SPI instructions the DI and DO pins become bidirectional IO0 and
IO1, with the additional I/O pins: IO2, IO3. Quad SPI instructions require the non-volatile Quad Enable bit (QE)
in Status Register-2 to be set.
6.4 Software Reset & Hardware /RESET pin
The W25Q64JV can be reset to the initial power-on state by a software Reset sequence. This sequence must
include two consecutive instructions: Enable Reset (66h) & Reset (99h). If the instruction sequence is
successfully accepted, the device will take approximately 30µS (tRST) to reset. No instruction will be accepted
during the reset period. For the SOIC-16 and TFBGA packages, W25Q64JV provides a dedicated hardware
/RESET pin. Drive the /RESET pin low for a minimum period of ~1µS (tRESET*) will interrupt any on-going
external/internal operations and reset the device to its initial power-on state. Hardware /RESET pin has higher
priority than other SPI input signals (/CS, CLK, IOs).
Note:
1. Hardware /RESET pin is available on SOIC-16 or TFBGA; please contact Winbond for his package.
2. While a faster /RESET pulse (as short as a few hundred nanoseconds) will often reset the device, a 1us minimum is recommended
to ensure reliable operation.
3. There is an internal pull-up resistor for the dedicated /RESET pin on the SOIC-16 and TFBGA-24 package. If the reset function is not
needed, this pin can be left floating in the system.
Publication Release Date: June 03, 2016
- 11 -
Revision C
W25Q64JV
6.5 Write Protection
Applications that use non-volatile memory must take into consideration the possibility of noise and other
adverse system conditions that may compromise data integrity. To address this concern, the W25Q64JV
provides several means to protect the data from inadvertent writes.
Write Protect Features
Device resets when VCC is below threshold
Time delay write disable after Power-up
Write enable/disable instructions and automatic write disable after erase or program
Software write protection using Status Registers
Additional Individual Block/Sector Locks for array protection
Write Protection using Power-down instruction
Lock Down write protection for Status Register until the next power-up
One Time Program (OTP) write protection for array and Security Registers using Status Register*
* Note: This feature is available upon special order. Please contact Winbond for details.
Upon power-up or at power-down, the W25Q64JV will maintain a reset condition while VCC is below the
threshold value of VWI, (See Power-up Timing and Voltage Levels and Figure 43). While reset, all operations
are disabled and no instructions are recognized. During power-up and after the VCC voltage exceeds VWI, all
program and erase related instructions are further disabled for a time delay of tPUW. This includes the Write
Enable, Page Program, Sector Erase, Block Erase, Chip Erase and the Write Status Register instructions.
Note that the chip select pin (/CS) must track the VCC supply level at power-up until the VCC-min level and
tVSL time delay is reached, and it must also track the VCC supply level at power-down to prevent adverse
command sequence. If needed a pull-up resister on /CS can be used to accomplish this.
After power-up the device is automatically placed in a write-disabled state with the Status Register Write
Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page Program, Sector
Erase, Block Erase, Chip Erase or Write Status Register instruction will be accepted. After completing a
program, erase or write instruction the Write Enable Latch (WEL) is automatically cleared to a write-disabled
state of 0.
Software controlled write protection is facilitated using the Write Status Register instruction and setting the
Status Register Protect (SRL) and Block Protect (CMP, SEC, TB, BP[2:0]) bits. These settings allow a portion
or the entire memory array to be configured as read only.
The W25Q64JV also provides another Write Protect method using the Individual Block Locks. Each 64KB
block (except the top and bottom blocks, total of 126 blocks) and each 4KB sector within the top/bottom blocks
(total of 32 sectors) are equipped with an Individual Block Lock bit. When the lock bit is 0, the corresponding
sector or block can be erased or programmed; when the lock bit is set to 1, Erase or Program commands
issued to the corresponding sector or block will be ignored. When the device is powered on, all Individual Block
Lock bits will be 1, so the entire memory array is protected from Erase/Program. An “Individual Block Unlock
(39h)” instruction must be issued to unlock any specific sector or block.
The WPS bit in Status Register-3 is used to decide which Write Protect scheme should be used. When WPS=0
(factory default), the device will only utilize CMP, SEC, TB, BP[2:0] bits to protect specific areas of the array;
when WPS=1, the device will utilize the Individual Block Locks for write protection.
Publication Release Date: June 03, 2016
- 12 -
Revision C
W25Q64JV
7. STATUS AND CONFIGURATION REGISTERS
Three Status and Configuration Registers are provided for W25Q64JV. The Read Status Register-1/2/3
instructions can be used to provide status on the availability of the flash memory array, whether the device is
write enabled or disabled, the state of write protection, Quad SPI setting, Security Register lock status,
Erase/Program Suspend status, output driver strength, power-up. The Write Status Register instruction can
be used to configure the device write protection features, Quad SPI setting, Security Register OTP locks, and
output driver strength. Write access to the Status Register is controlled by the state of the non-volatile Status
Register Protect bits (SRL), the Write Enable instruction, and during Standard/Dual SPI operations
7.1 Status Registers
S7
S6
TB
S5
S4
S3
S2
S1
S0
(R)
BP3
BP2
BP1
BP0
WEL BUSY
Reserved
Top/Bottom Protect Bit
(Volatile/Non-Volatile Writable)
Block Protect Bits
(Volatile/Non-Volatile Writable)
Write Enable Latch
(Status-Only)
Erase/Write In Progress
(Status-Only)
Figure 4a. Status Register-1
Erase/Write In Progress (BUSY) – Status Only
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a Page
Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register or
Erase/Program Security Register instruction. During this time the device will ignore further instructions except
for the Read Status Register and Erase/Program Suspend instruction (see tW, tPP, tSE, tBE, and tCE in AC
Characteristics). When the program, erase or write status/security register instruction has completed, the
BUSY bit will be cleared to a 0 state indicating the device is ready for further instructions.
Write Enable Latch (WEL) – Status Only
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to 1 after executing a Write
Enable Instruction. The WEL status bit is cleared to 0 when the device is write disabled. A write disable state
occurs upon power-up or after any of the following instructions: Write Disable, Page Program, Quad Page
Program, Sector Erase, Block Erase, Chip Erase, Write Status Register, Erase Security Register and Program
Security Register.
Block Protect Bits (BP2, BP1, BP0) – Volatile/Non-Volatile Writable
The Block Protect Bits (BP2, BP1, BP0) are non-volatile read/write bits in the status register (S4, S3, and S2)
that provide Write Protection control and status. Block Protect bits can be set using the Write Status Register
Instruction (see tW in AC characteristics). All, none or a portion of the memory array can be protected from
Program and Erase instructions (see Status Register Memory Protection table). The factory default setting for
the Block Protection Bits is 0, none of the array protected.
Publication Release Date: June 03, 2016
- 13 -
Revision C
W25Q64JV
Top/Bottom Block Protect (TB) – Volatile/Non-Volatile Writable
The non-volatile Top/Bottom bit (TB) controls if the Block Protect Bits (BP2, BP1, BP0) protect from the Top
(TB=0) or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table. The factory
default setting is TB=0. The TB bit can be set with the Write Status Register Instruction depending on the state
of the SRP, SRL and WEL bits.
Sector/Block Protect Bit (SEC) – Volatile/Non-Volatile Writable
The non-volatile Sector/Block Protect bit (SEC) controls if the Block Protect Bits (BP2, BP1, BP0) protect either
4KB Sectors (SEC=1) or 64KB Blocks (SEC=0) in the Top (TB=0) or the Bottom (TB=1) of the array as shown
in the Status Register Memory Protection table. The default setting is SEC=0.
Complement Protect (CMP) – Volatile/Non-Volatile Writable
The Complement Protect bit (CMP) is a non-volatile read/write bit in the status register (S14). It is used in
conjunction with SEC, TB, BP2, BP1 and BP0 bits to provide more flexibility for the array protection. Once
CMP is set to 1, previous array protection set by SEC, TB, BP2, BP1 and BP0 will be reversed. For instance,
when CMP=0, a top 64KB block can be protected while the rest of the array is not; when CMP=1, the top 64KB
block will become unprotected while the rest of the array become read-only. Please refer to the Status Register
Memory Protection table for details. The default setting is CMP=0.
Publication Release Date: June 03, 2016
- 14 -
Revision C
W25Q64JV
Status Register Protect (SRP, SRL)
The Status Register Lock bit (SRL) is a volatile/non-volatile read/write bit in the status register (S8). The SRL
bit controls the method of write protection to the Status Registers: temporary Power Lock-Down or permanently
One Time Program OTP.
SRL
Status Register Lock
Description
Status Registers are unlocked.
0
Non-Lock
Status Registers are locked and cannot be written to
until the next power-down, power-up cycle to reset
SRL=0.
Power Lock-Down
(Temporary/Volatile)
1
One Time Program(1)
(Permanently/Non-Volatile)
A special instruction flow can be used to permanently
OTP lock the Status Registers.
Note: Please contact Winbond for details regarding the special instruction sequence.
S15
S14
S13
LB3
S12
LB2
S11
LB1
S10
(R)
S9
S8
SUS
CMP
QE
SRL
Suspend Status
(Status-Only)
Complement Protect
(Volatile/Non-Volatile Writable)
Security Register Lock Bits
(Volatile/Non-Volatile OTP Writable)
Reserved
Quad Enable
(Volatile/Non-Volatile Writable)
Status Register Lock
(Volatile/Non-Volatile Writable)
Figure 4b. Status Register-2
Erase/Program Suspend Status (SUS) – Status Only
The Suspend Status bit is a read only bit in the status register (S15) that is set to 1 after executing a
Erase/Program Suspend (75h) instruction. The SUS status bit is cleared to 0 by Erase/Program Resume (7Ah)
instruction as well as a power-down, power-up cycle.
Security Register Lock Bits (LB3, LB2, LB1) – Volatile/Non-Volatile OTP Writable
The Security Register Lock Bits (LB3, LB2, LB1) are non-volatile One Time Program (OTP) bits in Status
Register (S13, S12, S11) that provide the write protect control and status to the Security Registers. The default
state of LB3-1 is 0, Security Registers are unlocked. LB3-1 can be set to 1 individually using the Write Status
Register instruction. LB3-1 are One Time Programmable (OTP), once it’s set to 1, the corresponding 256-Byte
Security Register will become read-only permanently.
Publication Release Date: June 03, 2016
- 15 -
Revision C
W25Q64JV
Quad Enable (QE) – Volatile/Non-Volatile Writable
The Quad Enable (QE) bit is set to 1 by default in the factory, therefore the device supports Standard/Dual
SPI as well as Quad SPI after power on. This bit cannot be reset to 0.
Note: QE bit is set to a 0 state, factory default for part numbers with ordering options “IM; please see
W25Q64JV-DTR data sheet.
Figure 4c. Status Register-3
Write Protect Selection (WPS) – Volatile/Non-Volatile Writable
The WPS bit is used to select which Write Protect scheme should be used. When WPS=0, the device will use
the combination of CMP, SEC, TB, BP[2:0] bits to protect a specific area of the memory array. When WPS=1,
the device will utilize the Individual Block Locks to protect any individual sector or blocks. The default value for
all Individual Block Lock bits is 1 upon device power on or after reset.
Output Driver Strength (DRV1, DRV0) – Volatile/Non-Volatile Writable
The DRV1 & DRV0 bits are used to determine the output driver strength for the Read operations.
DRV1, DRV0
Driver Strength
100%
0, 0
0, 1
1, 0
1, 1
75%
50%
25% (default)
Reserved Bits – Non Functional
There are a few reserved Status Register bits that may be read out as a “0” or “1”. It is recommended to ignore
the values of those bits. During a “Write Status Register” instruction, the Reserved Bits can be written as “0”,
but there will not be any effects.
Publication Release Date: June 03, 2016
- 16 -
Revision C
W25Q64JV
Status Register Memory Protection (WPS = 0, CMP = 0)
STATUS REGISTER(1)
W25Q64JV (64M-BIT) MEMORY PROTECTION(3)
PROTECTED
BLOCK(S)
PROTECTED
ADDRESSES
PROTECTED PROTECTED
DENSITY
SEC TB BP2 BP1 BP0
PORTION(2)
X
0
0
0
0
0
0
0
0
0
0
0
0
X
X
0
0
0
0
0
0
1
1
1
1
1
1
X
0
0
0
0
1
1
1
0
0
0
1
1
1
1
0
0
1
1
0
0
1
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
NONE
NONE
NONE
128KB
256KB
512KB
1MB
NONE
126 and 127 7E0000h – 7FFFFFh
124 thru 127 7C0000h – 7FFFFFh
120 thru 127 780000h – 7FFFFFh
112 thru 127 700000h – 7FFFFFh
Upper 1/64
Upper 1/32
Upper 1/16
Upper 1/8
Upper 1/4
Upper 1/2
Lower 1/64
Lower 1/32
Lower 1/16
Lower 1/8
Lower 1/4
Lower 1/2
ALL
96 thru 127
64 thru 127
0 and 1
600000h – 7FFFFFh
400000h – 7FFFFFh
000000h – 01FFFFh
000000h – 03FFFFh
000000h – 07FFFFh
000000h – 0FFFFFh
000000h – 1FFFFFh
000000h – 3FFFFFh
000000h – 7FFFFFh
2MB
4MB
128KB
256KB
512KB
1MB
0 thru 3
0 thru 7
0 thru 15
0 thru 31
0 thru 63
0 thru 127
2MB
4MB
8MB
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
1
0
0
0
1
0
1
1
0
0
1
1
0
1
0
1
X
1
0
1
X
127
127
127
127
0
7FF000h – 7FFFFFh
7FE000h – 7FFFFFh
7FC000h – 7FFFFFh
7F8000h – 7FFFFFh
000000h – 000FFFh
000000h – 001FFFh
000000h – 003FFFh
000000h – 007FFFh
4KB
8KB
U – 1/2048
U – 1/1024
U – 1/512
U – 1/256
L – 1/2048
L – 1/1024
L – 1/512
L – 1/256
16KB
32KB
4KB
0
8KB
0
16KB
32KB
0
Notes:
1. X = don’t care
2. L = Lower; U = Upper
3. If any Erase or Program command specifies a memory region that contains protected data portion, this command
will be ignored.
Publication Release Date: June 03, 2016
- 17 -
Revision C
W25Q64JV
Status Register Memory Protection (WPS = 0, CMP = 1)
STATUS REGISTER(1)
W25Q64JV (64M-BIT) MEMORY PROTECTION(3)
PROTECTED
BLOCK(S)
PROTECTED
ADDRESSES
PROTECTED
DENSITY
PROTECTED
PORTION(2)
SEC
TB BP2 BP1 BP0
X
0
0
0
0
0
0
0
0
0
0
0
0
X
X
0
0
0
0
0
0
1
1
1
1
1
1
X
0
0
0
0
1
1
1
0
0
0
1
1
1
1
0
0
1
1
0
0
1
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0 thru 127
0 thru 125
0 thru 123
0 thru 119
0 thru 111
0 thru 95
000000h – 7FFFFFh
000000h – 7DFFFFh
000000h – 7BFFFFh
000000h – 77FFFFh
000000h – 6FFFFFh
000000h – 5FFFFFh
000000h – 3FFFFFh
020000h – 7FFFFFh
040000h – 7FFFFFh
080000h – 7FFFFFh
100000h – 7FFFFFh
200000h – 7FFFFFh
400000h – 7FFFFFh
NONE
8MB
8,064KB
7,936KB
7,680KB
7MB
ALL
Lower 63/64
Lower 31/32
Lower 15/16
Lower 7/8
Lower 3/4
Lower 1/2
Upper 63/64
Upper 31/32
Upper 15/16
Upper 7/8
Upper 3/4
Upper 1/2
NONE
5MB
0 thru 63
4MB
2 thru 127
4 thru 127
8 thru 127
16 thru 127
32 thru 127
64 thru 127
NONE
8,064KB
7,936KB
7,680KB
7MB
5MB
4MB
NONE
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
1
0
0
0
1
0
1
1
0
0
1
1
0
1
0
1
X
1
0
1
X
0 thru 127
0 thru 127
0 thru 127
0 thru 127
0 thru 127
0 thru 127
0 thru 127
0 thru 127
000000h – 7FEFFFh
000000h – 7FDFFFh
000000h – 7FBFFFh
000000h – 7F7FFFh
001000h – 7FFFFFh
002000h – 7FFFFFh
004000h – 7FFFFFh
008000h – 7FFFFFh
8,188KB
8,184KB
8,176KB
8,160KB
8,188KB
8,184KB
8,176KB
8,160KB
L – 2047/2048
L – 1023/1024
L – 511/512
L – 255/256
L – 2047/2048
L – 1023/1024
L – 511/512
L – 255/256
Notes:
1. X = don’t care
2. L = Lower; U = Upper
3. If any Erase or Program command specifies a memory region that contains protected data portion, this command
will be ignored.
Publication Release Date: June 03, 2016
- 18 -
Revision C
W25Q64JV
Individual Block Memory Protection (WPS=1)
Sector 15 (4KB)
Sector 14 (4KB)
Sector 1 (4KB)
Sector 0 (4KB)
Individual Block Locks:
32 Sectors (Top/Bottom)
126 Blocks
Block 126 (64KB)
Individual Block Lock:
36h + Address
Individual Block Unlock:
39h + Address
Read Block Lock:
3Dh + Address
Global Block Lock:
7Eh
Block 1 (64KB)
Global Block Unlock:
98h
Sector 15 (4KB)
Sector 14 (4KB)
Sector 1 (4KB)
Sector 0 (4KB)
Figure 4d. Individual Block/Sector Locks
Notes:
1. Individual Block/Sector protection is only valid when WPS=1.
2. All individual block/sector lock bits are set to 1 by default after power up, all memory array is protected.
Publication Release Date: June 03, 2016
Revision C
- 19 -
W25Q64JV
8. INSTRUCTIONS
The Standard/Dual/Quad SPI instruction set of the W25Q64JV consists of 48 basic instructions that are fully
controlled through the SPI bus (see Instruction Set Table1-2). Instructions are initiated with the falling edge of
Chip Select (/CS). The first byte of data clocked into the DI input provides the instruction code. Data on the DI
input is sampled on the rising edge of clock with most significant bit (MSB) first.
Instructions vary in length from a single byte to several bytes and may be followed by address bytes, data
bytes, dummy bytes (don’t care), and in some cases, a combination. Instructions are completed with the rising
edge of edge /CS. Clock relative timing diagrams for each instruction are included in Figures 5 through 57. All
read instructions can be completed after any clocked bit. However, all instructions that Write, Program or Erase
must complete on a byte boundary (/CS driven high after a full 8-bits have been clocked) otherwise the
instruction will be ignored. This feature further protects the device from inadvertent writes. Additionally, while
the memory is being programmed or erased, or when the Status Register is being written, all instructions
except for Read Status Register will be ignored until the program or erase cycle has completed.
8.1 Device ID and Instruction Set Tables
Manufacturer and Device Identification
MANUFACTURER ID
(MF7 - MF0)
Winbond Serial Flash
EFh
(ID15 - ID0)
9Fh
Device ID
Instruction
W25Q64JV
(ID7 - ID0)
ABh, 90h, 92h, 94h
16h
4017h
Publication Release Date: June 03, 2016
Revision C
- 20 -
W25Q64JV
Instruction Set Table 1 (Standard SPI Instructions)(1)
Data Input Output
Byte 1
Byte 2
8
Byte 3
8
Byte 4
8
Byte 5
8
Byte 6
8
Byte 7
8
Number of Clock(1-1-1)
Write Enable
8
06h
50h
04h
Volatile SR Write Enable
Write Disable
Release Power-down / ID
Manufacturer/Device ID
JEDEC ID
ABh
90h
9Fh
4Bh
Dummy
Dummy
Dummy
Dummy
Dummy
00h
(ID7-ID0)(2)
(MF7-MF0)
(ID7-ID0)
(UID63-0)
(MF7-MF0)
Dummy
(ID15-ID8)
Dummy
(ID7-ID0)
Dummy
Read Unique ID
Dummy
Read Data
03h
0Bh
02h
A23-A16
A23-A16
A23-A16
A15-A8
A15-A8
A15-A8
A7-A0
A7-A0
A7-A0
(D7-D0)
Dummy
D7-D0
Fast Read
(D7-D0)
D7-D0(3)
Page Program
Sector Erase (4KB)
Block Erase (32KB)
Block Erase (64KB)
Chip Erase
20h
52h
A23-A16
A23-A16
A23-A16
A15-A8
A15-A8
A15-A8
A7-A0
A7-A0
A7-A0
D8h
C7h/60h
Read Status Register-1
Write Status Register-1(4)
Read Status Register-2
Write Status Register-2
Read Status Register-3
Write Status Register-3
Read SFDP Register
Erase Security Register(5)
Program Security Register(5)
Read Security Register(5)
Global Block Lock
05h
01h
35h
31h
15h
11h
5Ah
44h
42h
48h
7Eh
98h
3Dh
36h
39h
75h
7Ah
B9h
66h
99h
(S7-S0)(2)
(S7-S0)(4)
(S15-S8)(2)
(S15-S8)
(S23-S16)(2)
(S23-S16)
00h
00h
A7–A0
A7-A0
A7-A0
A7-A0
dummy
(D7-0)
A23-A16
A23-A16
A23-A16
A15-A8
A15-A8
A15-A8
D7-D0
D7-D0(3)
(D7-D0)
Dummy
Global Block Unlock
Read Block Lock
A23-A16
A23-A16
A23-A16
A15-A8
A15-A8
A15-A8
A7-A0
A7-A0
A7-A0
(L7-L0)
Individual Block Lock
Individual Block Unlock
Erase / Program Suspend
Erase / Program Resume
Power-down
Enable Reset
Reset Device
Publication Release Date: June 03, 2016
Revision C
- 21 -
W25Q64JV
Instruction Set Table 2 (Dual/Quad SPI Instructions)(1)
Data Input Output
Number of Clock(1-1-2)
Byte 1
8
Byte 2
8
Byte 3
8
Byte 4
8
Byte 5
4
Byte 6
4
Byte 7
4
Byte 8
4
Fast Read Dual Output
Number of Clock(1-2-2)
Fast Read Dual I/O
3Bh
8
A23-A16
4
A15-A8
4
A7-A0
4
Dummy
4
Dummy
4
(D7-D0)(7)
4
4
2
BBh
92h
8
A23-A16(6)
A23-A16(6)
8
A15-A8(6)
A15-A8(6)
8
A7-A0(6)
00(6)
8
Dummy(11)
Dummy(11)
2
(D7-D0)(7)
(MF7-MF0)
2
Mftr./Device ID Dual I/O
Number of Clock(1-1-4)
Quad Input Page Program
Fast Read Quad Output
Number of Clock(1-4-4)
(ID7-ID0)(7)
2
32h
6Bh
8
A23-A16
A23-A16
2
A15-A8
A15-A8
2
A7-A0
A7-A0
2
(D7-D0)(9)
Dummy
2
(D7-D0)(3)
Dummy
2
…
Dummy
(D7-D0)(10)
2
2
(MF7-
Mftr./Device ID Quad I/O
94h
A23-A16(8)
A23-A16
Dummy
A15-A8(8)
00(8)
Dummy(11)
Dummy(11)
W8-W0
Dummy
Dummy
Dummy
Dummy
MF0)(10)
Fast Read Quad I/O
Set Burst with Wrap
EBh
77h
A15-A8
Dummy
A7-A0
(D7-D0)
Dummy
Notes:
1. Data bytes are shifted with Most Significant Bit first. Byte fields with data in parenthesis “( )” indicate data output
from the device on either 1, 2 or 4 IO pins.
2. The Status Register contents and Device ID will repeat continuously until /CS terminates the instruction.
3. At least one byte of data input is required for Page Program, Quad Page Program and Program Security
Registers, up to 256 bytes of data input. If more than 256 bytes of data are sent to the device, the addressing
will wrap to the beginning of the page and overwrite previously sent data.
4. Write Status Register-1 (01h) can also be used to program Status Register-1&2, see section 8.2.5.
5. Security Register Address:
Security Register 1: A23-16 = 00h; A15-8 = 10h; A7-0 = byte address
Security Register 2: A23-16 = 00h; A15-8 = 20h; A7-0 = byte address
Security Register 3: A23-16 = 00h; A15-8 = 30h; A7-0 = byte address
6. Dual SPI address input format:
IO0 = A22, A20, A18, A16, A14, A12, A10, A8 A6, A4, A2, A0, M6, M4, M2, M0
IO1 = A23, A21, A19, A17, A15, A13, A11, A9 A7, A5, A3, A1, M7, M5, M3, M1
7. Dual SPI data output format:
IO0 = (D6, D4, D2, D0)
IO1 = (D7, D5, D3, D1)
8. Quad SPI address input format:
IO0 = A20, A16, A12, A8, A4, A0, M4, M0
Set Burst with Wrap input format:
IO0 = x, x, x, x, x, x, W4, x
IO1 = x, x, x, x, x, x, W5, x
IO2 = x, x, x, x, x, x, W6, x
IO1 = A21, A17, A13, A9, A5, A1, M5, M1
IO2 = A22, A18, A14, A10, A6, A2, M6, M2
IO3 = A23, A19, A15, A11, A7, A3, M7, M3
IO3 = x, x, x, x, x, x, x,
x
9. Quad SPI data input/output format:
IO0 = (D4, D0, …..)
IO1 = (D5, D1, …..)
IO2 = (D6, D2, …..)
IO3 = (D7, D3, …..)
10. Fast Read Quad I/O data output format:
IO0 = (x, x, x, x, D4, D0, D4, D0)
IO1 = (x, x, x, x, D5, D1, D5, D1)
IO2 = (x, x, x, x, D6, D2, D6, D2)
IO3 = (x, x, x, x, D7, D3, D7, D3)
11. The first dummy is M7-M0 should be set to Fxh
Publication Release Date: June 03, 2016
Revision C
- 22 -
W25Q64JV
8.2 Instruction Descriptions
Write Enable (06h)
The Write Enable instruction (Figure 5) sets the Write Enable Latch (WEL) bit in the Status Register to a 1.
The WEL bit must be set prior to every Page Program, Quad Page Program, Sector Erase, Block Erase, Chip
Erase, Write Status Register and Erase/Program Security Registers instruction. The Write Enable instruction
is entered by driving /CS low, shifting the instruction code “06h” into the Data Input (DI) pin on the rising edge
of CLK, and then driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (06h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 5. Write Enable Instruction for SPI Mode
Write Enable for Volatile Status Register (50h)
The non-volatile Status Register bits described in section 7.1 can also be written to as volatile bits. This gives
more flexibility to change the system configuration and memory protection schemes quickly without waiting for
the typical non-volatile bit write cycles or affecting the endurance of the Status Register non-volatile bits. To
write the volatile values into the Status Register bits, the Write Enable for Volatile Status Register (50h)
instruction must be issued prior to a Write Status Register (01h) instruction. Write Enable for Volatile Status
Register instruction (Figure 6) will not set the Write Enable Latch (WEL) bit, it is only valid for the Write Status
Register instruction to change the volatile Status Register bit values.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (50h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 6. Write Enable for Volatile Status Register Instruction for SPI Mode)
Publication Release Date: June 03, 2016
Revision C
- 23 -
W25Q64JV
Write Disable (04h)
The Write Disable instruction (Figure 7) resets the Write Enable Latch (WEL) bit in the Status Register to a 0.
The Write Disable instruction is entered by driving /CS low, shifting the instruction code “04h” into the DI pin
and then driving /CS high. Note that the WEL bit is automatically reset after Power-up and upon completion of
the Write Status Register, Erase/Program Security Registers, Page Program, Quad Page Program, Sector
Erase, Block Erase, Chip Erase and Reset instructions.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (04h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 7. Write Disable Instruction for SPI Mode
Read Status Register-1 (05h), Status Register-2 (35h) & Status Register-3 (15h)
The Read Status Register instructions allow the 8-bit Status Registers to be read. The instruction is entered
by driving /CS low and shifting the instruction code “05h” for Status Register-1, “35h” for Status Register-2 or
“15h” for Status Register-3 into the DI pin on the rising edge of CLK. The status register bits are then shifted
out on the DO pin at the falling edge of CLK with most significant bit (MSB) first as shown in Figure 8. Refer
to section 7.1 for Status Register descriptions.
The Read Status Register instruction may be used at any time, even while a Program, Erase or Write Status
Register cycle is in progress. This allows the BUSY status bit to be checked to determine when the cycle is
complete and if the device can accept another instruction. The Status Register can be read continuously, as
shown in Figure 8. The instruction is completed by driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
Instruction (05h/35h/15h)
High Impedance
DI
(IO0)
Status Register-1/2/3 out
Status Register-1/2/3 out
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
= MSB
*
*
*
Figure 8. Read Status Register Instruction
Publication Release Date: June 03, 2016
Revision C
- 24 -
W25Q64JV
Write Status Register-1 (01h), Status Register-2 (31h) & Status Register-3 (11h)
The Write Status Register instruction allows the Status Registers to be written. The writable Status Register
bits include:SEC, TB, BP[2:0] in Status Register-1; CMP, LB[3:1], QE, SRL in Status Register-2; DRV1, DRV0,
WPS in Status Register-3. All other Status Register bit locations are read-only and will not be affected by the
Write Status Register instruction. LB[3:1] are non-volatile OTP bits, once it is set to 1, it cannot be cleared to
0.
To write non-volatile Status Register bits, a standard Write Enable (06h) instruction must previously have been
executed for the device to accept the Write Status Register instruction (Status Register bit WEL must equal
1). Once write enabled, the instruction is entered by driving /CS low, sending the instruction code
“01h/31h/11h”, and then writing the status register data byte as illustrated in Figure 9a.
To write volatile Status Register bits, a Write Enable for Volatile Status Register (50h) instruction must have
been executed prior to the Write Status Register instruction (Status Register bit WEL remains 0). However,
SRL and LB[3:1] cannot be changed from “1” to “0” because of the OTP protection for these bits. Upon power
off or the execution of a Software/Hardware Reset, the volatile Status Register bit values will be lost, and the
non-volatile Status Register bit values will be restored.
During non-volatile Status Register write operation (06h combined with 01h/31h/11h), after /CS is driven high,
the self-timed Write Status Register cycle will commence for a time duration of tW (See AC Characteristics).
While the Write Status Register cycle is in progress, the Read Status Register instruction may still be accessed
to check the status of the BUSY bit. The BUSY bit is a 1 during the Write Status Register cycle and a 0 when
the cycle is finished and ready to accept other instructions again. After the Write Status Register cycle has
finished, the Write Enable Latch (WEL) bit in the Status Register will be cleared to 0.
During volatile Status Register write operation (50h combined with 01h/31h/11h), after /CS is driven high, the
Status Register bits will be refreshed to the new values within the time period of tSHSL2 (See AC
Characteristics). BUSY bit will remain 0 during the Status Register bit refresh period.
Refer to section 7.1 for Status Register descriptions.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
Register-1/2/3 in
Mode 3
Mode 0
CLK
Instruction
(01h/31h/11h)
DI
(IO0)
7
6
5
4
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 9a. Write Status Register-1/2/3 Instruction
Publication Release Date: June 03, 2016
Revision C
- 25 -
W25Q64JV
The W25Q64JV is also backward compatible to Winbond’s previous generations of serial flash memories, in
which the Status Register-1&2 can be written using a single “Write Status Register-1 (01h)” command. To
complete the Write Status Register-1&2 instruction, the /CS pin must be driven high after the sixteenth bit of
data that is clocked in as shown in Figure 9c. If /CS is driven high after the eighth clock, the Write Status
Register-1 (01h) instruction will only program the Status Register-1, the Status Register-2 will not be affected
(Previous generations will clear CMP and QE bits).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
Mode 3
Mode 0
CLK
Instruction (01h)
Status Register 1 in
Status Register 2 in
DI
(IO0)
7
6
5
4
3
2
1
0
15 14 13 12 11 10
9
8
*
*
High Impedance
DO
(IO1)
= MSB
*
Figure 9c. Write Status Register-1/2 Instruction
Publication Release Date: June 03, 2016
Revision C
- 26 -
W25Q64JV
Read Data (03h)
The Read Data instruction allows one or more data bytes to be sequentially read from the memory. The
instruction is initiated by driving the /CS pin low and then shifting the instruction code “03h” followed by a 24-
bit address (A23-A0) into the DI pin. The code and address bits are latched on the rising edge of the CLK pin.
After the address is received, the data byte of the addressed memory location will be shifted out on the DO
pin at the falling edge of CLK with most significant bit (MSB) first. The address is automatically incremented
to the next higher address after each byte of data is shifted out allowing for a continuous stream of data. This
means that the entire memory can be accessed with a single instruction as long as the clock continues. The
instruction is completed by driving /CS high.
The Read Data instruction sequence is shown in Figure 14. If a Read Data instruction is issued while an Erase,
Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any effects on the
current cycle. The Read Data instruction allows clock rates from D.C. to a maximum of fR (see AC Electrical
Characteristics).
The Read Data (03h) instruction is only supported in Standard SPI mode.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38 39
CLK
Instruction (03h)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
Data Out 1
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
7
= MSB
*
*
Figure 14. Read Data Instruction
Publication Release Date: June 03, 2016
Revision C
- 27 -
W25Q64JV
Fast Read (0Bh)
The Fast Read instruction is similar to the Read Data instruction except that it can operate at the highest
possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight “dummy”
clocks after the 24-bit address as shown in Figure 16. The dummy clocks allow the devices internal circuits
additional time for setting up the initial address. During the dummy clocks the data value on the DO pin is a
“don’t care”.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (0Bh)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
CLK
Dummy Clocks
DI
(IO0)
0
Data Out 1
Data Out 2
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
*
*
Figure 16. Fast Read Instruction
Publication Release Date: June 03, 2016
Revision C
- 28 -
W25Q64JV
Fast Read Dual Output (3Bh)
The Fast Read Dual Output (3Bh) instruction is similar to the standard Fast Read (0Bh) instruction except that
data is output on two pins; IO0 and IO1. This allows data to be transferred at twice the rate of standard SPI
devices. The Fast Read Dual Output instruction is ideal for quickly downloading code from Flash to RAM upon
power-up or for applications that cache code-segments to RAM for execution.
Similar to the Fast Read instruction, the Fast Read Dual Output instruction can operate at the highest possible
frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight “dummy” clocks after
the 24-bit address as shown in Figure 18. The dummy clocks allow the device's internal circuits additional time
for setting up the initial address. The input data during the dummy clocks is “don’t care”. However, the IO0 pin
should be high-impedance prior to the falling edge of the first data out clock.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (3Bh)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
CLK
IO0 switches from
Dummy Clocks
Input to Output
DI
(IO0)
0
6
4
2
0
6
4
5
2
3
0
1
6
4
5
2
3
0
1
6
4
5
2
3
0
1
6
7
High Impedance
DO
(IO1)
7
5
3
1
7
7
7
Data Out 1
Data Out 2
Data Out 3
Data Out 4
*
*
*
*
Figure 18. Fast Read Dual Output Instruction
Publication Release Date: June 03, 2016
Revision C
- 29 -
W25Q64JV
Fast Read Quad Output (6Bh)
The Fast Read Quad Output (6Bh) instruction is similar to the Fast Read Dual Output (3Bh) instruction except
that data is output on four pins, IO0, IO1, IO2, and IO3. The Quad Enable (QE) bit in Status Register-2 must be
set to 1 before the device will accept the Fast Read Quad Output Instruction. The Fast Read Quad Output
Instruction allows data to be transferred at four times the rate of standard SPI devices.
The Fast Read Quad Output instruction can operate at the highest possible frequency of FR (see AC Electrical
Characteristics). This is accomplished by adding eight “dummy” clocks after the 24-bit address as shown in
Figure 20. The dummy clocks allow the device's internal circuits additional time for setting up the initial address.
The input data during the dummy clocks is “don’t care”. However, the IO pins should be high-impedance prior
to the falling edge of the first data out clock.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
IO0
Instruction (6Bh)
24-Bit Address
23 22 21
3
2
1
0
*
High Impedance
High Impedance
High Impedance
IO1
IO2
IO3
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
CLK
IO0 switches from
Dummy Clocks
Input to Output
0
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
IO0
IO1
IO2
IO3
High Impedance
High Impedance
High Impedance
Byte 1
Byte 2
Byte 3
Byte 4
Figure 20. Fast Read Quad Output Instruction
Publication Release Date: June 03, 2016
Revision C
- 30 -
W25Q64JV
Fast Read Dual I/O (BBh)
The Fast Read Dual I/O (BBh) instruction allows for improved random access while maintaining two IO pins,
IO0 and IO1. It is similar to the Fast Read Dual Output (3Bh) instruction but with the capability to input the
Address bits (A23-0) two bits per clock. This reduced instruction overhead may allow for code execution (XIP)
directly from the Dual SPI in some applications.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
Instruction (BBh)
A23-16
A15-8
A7-0
M7-0
DI
(IO0)
22 20 18 16 14 12 10
8
9
6
7
4
2
0
1
6
4
2
0
1
DO
(IO1)
23 21 19 17 15 13 11
5
3
7
5
3
*
*
= MSB
*
/CS
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
CLK
IOs switch from
Input to Output
DI
(IO0)
0
1
6
4
5
2
0
6
4
5
2
0
1
6
4
5
2
0
1
6
4
5
2
0
1
6
7
DO
(IO1)
7
3
1
7
3
7
3
7
3
*
*
*
*
Byte 1
Byte 2
Byte 3
Byte 4
Figure 22. Fast Read Dual I/O Instruction (M5-4=Fxh)
Publication Release Date: June 03, 2016
Revision C
- 31 -
W25Q64JV
Fast Read Quad I/O (EBh)
The Fast Read Quad I/O (EBh) instruction is similar to the Fast Read Dual I/O (BBh) instruction except that
address and data bits are input and output through four pins IO0, IO1, IO2 and IO3 and four Dummy clocks are
required in SPI mode prior to the data output. The Quad I/O dramatically reduces instruction overhead allowing
faster random access for code execution (XIP) directly from the Quad SPI. The Quad Enable bit (QE) of Status
Register-2 must be set to enable the Fast Read Quad I/O Instruction.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
IOs switch from
Input to Output
A23-16
A15-8
A7-0
M7-0
Dummy
Dummy
Instruction (EBh)
20 16 12
21 17 13
8
9
4
0
1
2
3
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
IO0
IO1
IO2
IO3
5
6
7
5
6
7
22 18 14 10
23 19 15 11
Byte 1
Byte 2
Byte 3
Figure 24a. Fast Read Quad I/O Instruction (M5-4=Fxh)
Fast Read Quad I/O with “8/16/32/64-Byte Wrap Around” in Standard SPI mode
The Fast Read Quad I/O instruction can also be used to access a specific portion within a page by issuing a
“Set Burst with Wrap” (77h) command prior to EBh. The “Set Burst with Wrap” (77h) command can either
enable or disable the “Wrap Around” feature for the following EBh commands. When “Wrap Around” is
enabled, the data being accessed can be limited to either an 8, 16, 32 or 64-byte section of a 256-byte page.
The output data starts at the initial address specified in the instruction, once it reaches the ending boundary
of the 8/16/32/64-byte section, the output will wrap around to the beginning boundary automatically until /CS
is pulled high to terminate the command.
The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then fill
the cache afterwards within a fixed length (8/16/32/64-byte) of data without issuing multiple read commands.
The “Set Burst with Wrap” instruction allows three “Wrap Bits”, W6-4 to be set. The W4 bit is used to enable
or disable the “Wrap Around” operation while W6-5 are used to specify the length of the wrap around section
within a page. Refer to section 8.2.37 for detail descriptions.
Publication Release Date: June 03, 2016
- 32 -
Revision C
W25Q64JV
Set Burst with Wrap (77h)
In Standard SPI mode, the Set Burst with Wrap (77h) instruction is used in conjunction with “Fast Read Quad
I/O” instructions to access a fixed length of 8/16/32/64-byte section within a 256-byte page. Certain
applications can benefit from this feature and improve the overall system code execution performance.
Similar to a Quad I/O instruction, the Set Burst with Wrap instruction is initiated by driving the /CS pin low and
then shifting the instruction code “77h” followed by 24 dummy bits and 8 “Wrap Bits”, W7-0. The instruction
sequence is shown in Figure 28. Wrap bit W7 and the lower nibble W3-0 are not used.
W4 = 0
Wrap Around
W4 =1 (DEFAULT)
W6, W5
Wrap Length
Wrap Around
Wrap Length
0
0
Yes
8-byte
No
N/A
0
1
1
1
0
1
Yes
Yes
Yes
16-byte
32-byte
64-byte
No
No
No
N/A
N/A
N/A
Once W6-4 is set by a Set Burst with Wrap instruction, the following “Fast Read Quad I/O” instructions will use
the W6-4 setting to access the 8/16/32/64-byte section within any page. To exit the “Wrap Around” function
and return to normal read operation, another Set Burst with Wrap instruction should be issued to set W4 = 1.
The default value of W4 upon power on or after a software/hardware reset is 1.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
Mode 3
Mode 0
CLK
don't
care
don't
care
don't
care
Wrap Bit
Instruction (77h)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
w4
w5
w6
X
X
X
X
X
IO0
IO1
IO2
IO3
X
X
X
X
X
X
X
X
X
Figure 28. Set Burst with Wrap Instruction
Publication Release Date: June 03, 2016
Revision C
- 33 -
W25Q64JV
Page Program (02h)
The Page Program instruction allows from one byte to 256 bytes (a page) of data to be programmed at
previously erased (FFh) memory locations. A Write Enable instruction must be executed before the device will
accept the Page Program Instruction (Status Register bit WEL= 1). The instruction is initiated by driving the
/CS pin low then shifting the instruction code “02h” followed by a 24-bit address (A23-A0) and at least one
data byte, into the DI pin. The /CS pin must be held low for the entire length of the instruction while data is
being sent to the device. The Page Program instruction sequence is shown in Figure 29.
If an entire 256 byte page is to be programmed, the last address byte (the 8 least significant address bits)
should be set to 0. If the last address byte is not zero, and the number of clocks exceeds the remaining page
length, the addressing will wrap to the beginning of the page. In some cases, less than 256 bytes (a partial
page) can be programmed without having any effect on other bytes within the same page. One condition to
perform a partial page program is that the number of clocks cannot exceed the remaining page length. If more
than 256 bytes are sent to the device the addressing will wrap to the beginning of the page and overwrite
previously sent data.
As with the write and erase instructions, the /CS pin must be driven high after the eighth bit of the last byte
has been latched. If this is not done the Page Program instruction will not be executed. After /CS is driven
high, the self-timed Page Program instruction will commence for a time duration of tpp (See AC
Characteristics). While the Page Program cycle is in progress, the Read Status Register instruction may still
be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Page Program cycle and
becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the
Page Program cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The
Page Program instruction will not be executed if the addressed page is protected by the Block Protect (CMP,
SEC, TB, BP2, BP1, and BP0) bits or the Individual Block/Sector Locks.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38 39
CLK
Instruction (02h)
24-Bit Address
Data Byte 1
DI
(IO0)
23 22 21
3
2
1
0
7
6
5
4
3
2
1
0
*
*
= MSB
*
/CS
39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
Mode 3
Mode 0
CLK
Data Byte 2
Data Byte 3
Data Byte 256
DI
(IO0)
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
*
*
*
Figure 29. Page Program Instruction
Publication Release Date: June 03, 2016
Revision C
- 34 -
W25Q64JV
Quad Input Page Program (32h)
The Quad Page Program instruction allows up to 256 bytes of data to be programmed at previously erased
(FFh) memory locations using four pins: IO0, IO1, IO2, and IO3. The Quad Page Program can improve
performance for PROM Programmer and applications that have slow clock speeds <5MHz. Systems with
faster clock speed will not realize much benefit for the Quad Page Program instruction since the inherent page
program time is much greater than the time it take to clock-in the data.
To use Quad Page Program the Quad Enable (QE) bit in Status Register-2 must be set to 1. A Write Enable
instruction must be executed before the device will accept the Quad Page Program instruction (Status
Register-1, WEL=1). The instruction is initiated by driving the /CS pin low then shifting the instruction code
“32h” followed by a 24-bit address (A23-A0) and at least one data byte, into the IO pins. The /CS pin must be
held low for the entire length of the instruction while data is being sent to the device. All other functions of
Quad Page Program are identical to standard Page Program. The Quad Page Program instruction sequence
is shown in Figure 30.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
IO0
Instruction (32h)
24-Bit Address
23 22 21
3
2
1
0
*
IO1
IO2
IO3
= MSB
*
/CS
31 32 33 34 35 36 37
Mode 3
Mode 0
CLK
Byte
253
Byte
254
Byte
255
Byte
256
Byte 1
Byte 2
Byte 3
0
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
0
1
2
3
4
5
6
0
1
2
3
4
0
1
2
3
4
0
1
2
3
IO0
IO1
IO2
IO3
5
6
5
6
5
6
7
7
7
7
7
7
7
*
*
*
*
*
*
*
Figure 30. Quad Input Page Program Instruction
Publication Release Date: June 03, 2016
Revision C
- 35 -
W25Q64JV
8.3 Sector Erase (20h)
The Sector Erase instruction sets all memory within a specified sector (4K-bytes) to the erased state of all 1s
(FFh). A Write Enable instruction must be executed before the device will accept the Sector Erase Instruction
(Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the
instruction code “20h” followed a 24-bit sector address (A23-A0). The Sector Erase instruction sequence is
shown in Figure 31.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the
Sector Erase instruction will not be executed. After /CS is driven high, the self-timed Sector Erase instruction
will commence for a time duration of tSE (See AC Characteristics). While the Sector Erase cycle is in progress,
the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY
bit is a 1 during the Sector Erase cycle and becomes a 0 when the cycle is finished and the device is ready to
accept other instructions again. After the Sector Erase cycle has finished the Write Enable Latch (WEL) bit in
the Status Register is cleared to 0. The Sector Erase instruction will not be executed if the addressed page is
protected by the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits or the Individual Block/Sector Locks.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (20h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 31. Sector Erase Instruction
Publication Release Date: June 03, 2016
Revision C
- 36 -
W25Q64JV
32KB Block Erase (52h)
The Block Erase instruction sets all memory within a specified block (32K-bytes) to the erased state of all 1s
(FFh). A Write Enable instruction must be executed before the device will accept the Block Erase Instruction
(Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the
instruction code “52h” followed a 24-bit block address (A23-A0). The Block Erase instruction sequence is
shown in Figure 32.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the
Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase instruction
will commence for a time duration of tBE1 (See AC Characteristics). While the Block Erase cycle is in progress,
the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY
bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the device is ready to
accept other instructions again. After the Block Erase cycle has finished the Write Enable Latch (WEL) bit in
the Status Register is cleared to 0. The Block Erase instruction will not be executed if the addressed page is
protected by the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits or the Individual Block/Sector Locks.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (52h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 32. 32KB Block Erase Instruction
Publication Release Date: June 03, 2016
Revision C
- 37 -
W25Q64JV
64KB Block Erase (D8h)
The Block Erase instruction sets all memory within a specified block (64K-bytes) to the erased state of all 1s
(FFh). A Write Enable instruction must be executed before the device will accept the Block Erase Instruction
(Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the
instruction code “D8h” followed a 24-bit block address (A23-A0). The Block Erase instruction sequence is
shown in Figure 33.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the
Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase instruction
will commence for a time duration of tBE (See AC Characteristics). While the Block Erase cycle is in progress,
the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY
bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the device is ready to
accept other instructions again. After the Block Erase cycle has finished the Write Enable Latch (WEL) bit in
the Status Register is cleared to 0. The Block Erase instruction will not be executed if the addressed page is
protected by the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits or the Individual Block/Sector Locks.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (D8h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 33. 64KB Block Erase Instruction
Publication Release Date: June 03, 2016
Revision C
- 38 -
W25Q64JV
Chip Erase (C7h / 60h)
The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A Write Enable
instruction must be executed before the device will accept the Chip Erase Instruction (Status Register bit WEL
must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code “C7h” or
“60h”. The Chip Erase instruction sequence is shown in Figure 34.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip Erase
instruction will not be executed. After /CS is driven high, the self-timed Chip Erase instruction will commence
for a time duration of tCE (See AC Characteristics). While the Chip Erase cycle is in progress, the Read Status
Register instruction may still be accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the
Chip Erase cycle and becomes a 0 when finished and the device is ready to accept other instructions again.
After the Chip Erase cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to
0. The Chip Erase instruction will not be executed if any memory region is protected by the Block Protect
(CMP, SEC, TB, BP2, BP1, and BP0) bits or the Individual Block/Sector Locks.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (C7h/60h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 34. Chip Erase Instruction
Publication Release Date: June 03, 2016
Revision C
- 39 -
W25Q64JV
Erase / Program Suspend (75h)
The Erase/Program Suspend instruction “75h”, allows the system to interrupt a Sector or Block Erase
operation or a Page Program operation and then read from or program/erase data to, any other sectors or
blocks. The Erase/Program Suspend instruction sequence is shown in Figure 35.
The Write Status Register instruction (01h) and Erase instructions (20h, 52h, D8h, C7h, 60h, 44h) are not
allowed during Erase Suspend. Erase Suspend is valid only during the Sector or Block erase operation. If
written during the Chip Erase operation, the Erase Suspend instruction is ignored. The Write Status Register
instruction (01h) and Program instructions (02h, 32h, 42h) are not allowed during Program Suspend. Program
Suspend is valid only during the Page Program or Quad Page Program operation.
The Erase/Program Suspend instruction “75h” will be accepted by the device only if the SUS bit in the Status
Register equals to 0 and the BUSY bit equals to 1 while a Sector or Block Erase or a Page Program operation
is on-going. If the SUS bit equals to 1 or the BUSY bit equals to 0, the Suspend instruction will be ignored by
the device. A maximum of time of “tSUS” (See AC Characteristics) is required to suspend the erase or program
operation. The BUSY bit in the Status Register will be cleared from 1 to 0 within “tSUS” and the SUS bit in the
Status Register will be set from 0 to 1 immediately after Erase/Program Suspend. For a previously resumed
Erase/Program operation, it is also required that the Suspend instruction “75h” is not issued earlier than a
minimum of time of “tSUS” following the preceding Resume instruction “7Ah”.
Unexpected power off during the Erase/Program suspend state will reset the device and release the suspend
state. SUS bit in the Status Register will also reset to 0. The data within the page, sector or block that was
being suspended may become corrupted. It is recommended for the user to implement system design
techniques against the accidental power interruption and preserve data integrity during erase/program
suspend state.
/CS
tSUS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (75h)
High Impedance
DI
(IO0)
DO
(IO1)
Accept instructions
Figure 35. Erase/Program Suspend Instruction
Publication Release Date: June 03, 2016
Revision C
- 40 -
W25Q64JV
Erase / Program Resume (7Ah)
The Erase/Program Resume instruction “7Ah” must be written to resume the Sector or Block Erase operation
or the Page Program operation after an Erase/Program Suspend. The Resume instruction “7Ah” will be
accepted by the device only if the SUS bit in the Status Register equals to 1 and the BUSY bit equals to 0.
After issued the SUS bit will be cleared from 1 to 0 immediately, the BUSY bit will be set from 0 to 1 within
200ns and the Sector or Block will complete the erase operation or the page will complete the program
operation. If the SUS bit equals to 0 or the BUSY bit equals to 1, the Resume instruction “7Ah” will be ignored
by the device. The Erase/Program Resume instruction sequence is shown in Figure 36.
Resume instruction is ignored if the previous Erase/Program Suspend operation was interrupted by
unexpected power off. It is also required that a subsequent Erase/Program Suspend instruction not to be
issued within a minimum of time of “tSUS” following a previous Resume instruction.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (7Ah)
DI
(IO0)
Resume previously
suspended Program or
Erase
Figure 36. Erase/Program Resume Instruction
Publication Release Date: June 03, 2016
Revision C
- 41 -
W25Q64JV
Power-down (B9h)
Although the standby current during normal operation is relatively low, standby current can be further reduced
with the Power-down instruction. The lower power consumption makes the Power-down instruction especially
useful for battery powered applications (See ICC1 and ICC2 in AC Characteristics). The instruction is initiated
by driving the /CS pin low and shifting the instruction code “B9h” as shown in Figure 37.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Power-down
instruction will not be executed. After /CS is driven high, the power-down state will entered within the time
duration of tDP (See AC Characteristics). While in the power-down state only the Release Power-down / Device
ID (ABh) instruction, which restores the device to normal operation, will be recognized. All other instructions
are ignored. This includes the Read Status Register instruction, which is always available during normal
operation. Ignoring all but one instruction makes the Power Down state a useful condition for securing
maximum write protection. The device always powers-up in the normal operation with the standby current of
ICC1.
/CS
tDP
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (B9h)
DI
(IO0)
Stand-by current
Power-down current
Figure 37. Deep Power-down Instruction
Publication Release Date: June 03, 2016
Revision C
- 42 -
W25Q64JV
Release Power-down / Device ID (ABh)
The Release from Power-down / Device ID instruction is a multi-purpose instruction. It can be used to release
the device from the power-down state, or obtain the devices electronic identification (ID) number.
To release the device from the power-down state, the instruction is issued by driving the /CS pin low, shifting
the instruction code “ABh” and driving /CS high as shown in Figure 38a. Release from power-down will take
the time duration of tRES1 (See AC Characteristics) before the device will resume normal operation and other
instructions are accepted. The /CS pin must remain high during the tRES1 time duration.
When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by driving
the /CS pin low and shifting the instruction code “ABh” followed by 3-dummy bytes. The Device ID bits are
then shifted out on the falling edge of CLK with most significant bit (MSB) first. The Device ID value for the
W25Q64JV is listed in Manufacturer and Device Identification table. The Device ID can be read continuously.
The instruction is completed by driving /CS high.
When used to release the device from the power-down state and obtain the Device ID, the instruction is the
same as previously described, and shown in Figure 38b, except that after /CS is driven high it must remain
high for a time duration of tRES2 (See AC Characteristics). After this time duration the device will resume
normal operation and other instructions will be accepted. If the Release from Power-down / Device ID
instruction is issued while an Erase, Program or Write cycle is in process (when BUSY equals 1) the instruction
is ignored and will not have any effects on the current cycle.
/CS
tRES1
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (ABh)
DI
(IO0)
Power-down current
Stand-by current
Figure 38a. Release Power-down Instruction
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31 32 33 34 35 36 37 38
Mode 3
Mode 0
tRES2
CLK
Instruction (ABh)
3 Dummy Bytes
DI
(IO0)
23 22
2
1
0
Device ID
*
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
*
= MSB
Power-down current
Stand-by current
*
Figure 38c. Release Power-down / Device ID Instruction
Publication Release Date: June 03, 2016
Revision C
- 43 -
W25Q64JV
Read Manufacturer / Device ID (90h)
The Read Manufacturer/Device ID instruction is an alternative to the Release from Power-down / Device ID
instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID.
The Read Manufacturer/Device ID instruction is very similar to the Release from Power-down / Device ID
instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code “90h” followed
by a 24-bit address (A23-A0) of 000000h. After which, the Manufacturer ID for Winbond (EFh) and the Device
ID are shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in Figure 39. The
Device ID values for the W25Q64JV are listed in Manufacturer and Device Identification table. The instruction
is completed by driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (90h)
Address (000000h)
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
Mode 3
Mode 0
CLK
DI
(IO0)
0
DO
(IO1)
7
6
5
4
3
2
1
0
Manufacturer ID (EFh)
Device ID
*
Figure 39. Read Manufacturer / Device ID Instruction
Publication Release Date: June 03, 2016
Revision C
- 44 -
W25Q64JV
Read Manufacturer / Device ID Dual I/O (92h)
The Read Manufacturer / Device ID Dual I/O instruction is an alternative to the Read Manufacturer / Device
ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID at 2x speed.
The Read Manufacturer / Device ID Dual I/O instruction is similar to the Fast Read Dual I/O instruction. The
instruction is initiated by driving the /CS pin low and shifting the instruction code “92h” followed by a 24-bit
address (A23-A0) of 000000h, but with the capability to input the Address bits two bits per clock. After which,
the Manufacturer ID for Winbond (EFh) and the Device ID are shifted out 2 bits per clock on the falling edge
of CLK with most significant bits (MSB) first as shown in Figure 40. The Device ID values for the W25Q64JV
are listed in Manufacturer and Device Identification table. The Manufacturer and Device IDs can be read
continuously, alternating from one to the other. The instruction is completed by driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
A23-16
A15-8
A7-0 (00h)
M7-0
Instruction (92h)
High Impedance
DI
(IO0)
6
4
2
0
1
6
4
2
0
1
6
4
2
0
1
6
4
2
0
1
DO
(IO1)
7
5
3
7
5
3
7
5
3
7
5
3
= MSB
*
*
*
*
*
/CS
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
Mode 3
Mode 0
CLK
IOs switch from
Input to Output
DI
(IO0)
0
1
6
4
5
2
0
6
4
5
2
3
0
1
6
4
5
2
3
0
1
6
4
5
2
3
0
1
DO
(IO1)
7
3
1
7
7
7
MFR ID
(repeat)
Device ID
(repeat)
*
*
*
*
MFR ID
Device ID
Figure 40. Read Manufacturer / Device ID Dual I/O Instruction
Note:
The “Continuous Read Mode” bits M(7-0) must be set to Fxh to be compatible with Fast Read Dual I/O instruction.
Publication Release Date: June 03, 2016
Revision C
- 45 -
W25Q64JV
Read Manufacturer / Device ID Quad I/O (94h)
The Read Manufacturer / Device ID Quad I/O instruction is an alternative to the Read Manufacturer / Device
ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID at 4x speed.
The Read Manufacturer / Device ID Quad I/O instruction is similar to the Fast Read Quad I/O instruction. The
instruction is initiated by driving the /CS pin low and shifting the instruction code “94h” followed by a four clock
dummy cycles and then a 24-bit address (A23-A0) of 000000h, but with the capability to input the Address bits
four bits per clock. After which, the Manufacturer ID for Winbond (EFh) and the Device ID are shifted out four
bits per clock on the falling edge of CLK with most significant bit (MSB) first as shown in Figure 41. The
Manufacturer and Device IDs can be read continuously, alternating from one to the other. The instruction is
completed by driving /CS high.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
A7-0
(00h)
IOs switch from
Input to Output
A23-16
A15-8
M7-0
Dummy
Dummy
Instruction (94h)
4
5
6
7
0
1
2
3
4
0
1
2
3
4
0
1
2
3
4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
IO0
IO1
IO2
IO3
High Impedance
High Impedance
High Impedance
5
6
7
5
6
7
5
6
7
MFR ID Device ID
/CS
23 24 25 26 27 28 29 30
Mode 3
Mode 0
CLK
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
IO0
IO1
IO2
IO3
MFR ID Device ID MFR ID Device ID
(repeat) (repeat) (repeat) (repeat)
Figure 41. Read Manufacturer / Device ID Quad I/O Instruction
Note:
The “Continuous Read Mode” bits M(7-0) must be set to Fxh to be compatible with Fast Read Quad I/O instruction.
Publication Release Date: June 03, 2016
Revision C
- 46 -
W25Q64JV
Read Unique ID Number (4Bh)
The Read Unique ID Number instruction accesses a factory-set read-only 64-bit number that is unique to each
W25Q64JV device. The ID number can be used in conjunction with user software methods to help prevent
copying or cloning of a system. The Read Unique ID instruction is initiated by driving the /CS pin low and
shifting the instruction code “4Bh” followed by a four bytes of dummy clocks. After which, the 64-bit ID is shifted
out on the falling edge of CLK as shown in Figure 42.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23
CLK
Instruction (4Bh)
Dummy Byte 1
Dummy Byte 2
DI
(IO0)
High Impedance
DO
(IO1)
/CS
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42
Mode 3
Mode 0
CLK
Dummy Byte 3
Dummy Byte 4
DI
(IO0)
High Impedance
DO
(IO1)
63 62 61
2
1
0
= MSB
64-bit Unique Serial Number
*
*
Figure 42. Read Unique ID Number Instruction
Publication Release Date: June 03, 2016
Revision C
- 47 -
W25Q64JV
Read JEDEC ID (9Fh)
For compatibility reasons, the W25Q64JV provides several instructions to electronically determine the identity
of the device. The Read JEDEC ID instruction is compatible with the JEDEC standard for SPI compatible serial
memories that was adopted in 2003. The instruction is initiated by driving the /CS pin low and shifting the
instruction code “9Fh”. The JEDEC assigned Manufacturer ID byte for Winbond (EFh) and two Device ID
bytes, Memory Type (ID15-ID8) and Capacity (ID7-ID0) are then shifted out on the falling edge of CLK with
most significant bit (MSB) first as shown in Figure 43. For memory type and capacity values refer to
Manufacturer and Device Identification table.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
CLK
Instruction (9Fh)
High Impedance
DI
(IO0)
Manufacturer ID (EFh)
DO
(IO1)
= MSB
*
/CS
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Mode 3
Mode 0
CLK
DI
(IO0)
Memory Type ID15-8
Capacity ID7-0
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
*
*
Figure 43. Read JEDEC ID Instruction
Publication Release Date: June 03, 2016
Revision C
- 48 -
W25Q64JV
Read SFDP Register (5Ah)
The W25Q64JV features a 256-Byte Serial Flash Discoverable Parameter (SFDP) register that contains
information about device configurations, available instructions and other features. The SFDP parameters are
stored in one or more Parameter Identification (PID) tables. Currently only one PID table is specified, but more
may be added in the future. The Read SFDP Register instruction is compatible with the SFDP standard initially
established in 2010 for PC and other applications, as well as the JEDEC standard JESD216-serials that is
published in 2011. Most Winbond SpiFlash Memories shipped after June 2011 (date code 1124 and beyond)
support the SFDP feature as specified in the applicable datasheet.
The Read SFDP instruction is initiated by driving the /CS pin low and shifting the instruction code “5Ah”
followed by a 24-bit address (A23-A0)(1) into the DI pin. Eight “dummy” clocks are also required before the
SFDP register contents are shifted out on the falling edge of the 40th CLK with most significant bit (MSB) first
as shown in Figure 44. For SFDP register values and descriptions, please refer to the Winbond Application
Note for SFDP Definition Table.
Note 1: A23-A8 = 0; A7-A0 are used to define the starting byte address for the 256-Byte SFDP Register.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (5Ah)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
CLK
Dummy Byte
DI
(IO0)
0
7
6
5
4
3
2
1
0
Data Out 1
Data Out 2
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
= MSB
*
*
*
Figure 44. Read SFDP Register Instruction Sequence Diagram
Publication Release Date: June 03, 2016
Revision C
- 49 -
W25Q64JV
Erase Security Registers (44h)
The W25Q64JV offers three 256-byte Security Registers which can be erased and programmed individually.
These registers may be used by the system manufacturers to store security and other important information
separately from the main memory array.
The Erase Security Register instruction is similar to the Sector Erase instruction. A Write Enable instruction
must be executed before the device will accept the Erase Security Register Instruction (Status Register bit
WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code “44h”
followed by a 24-bit address (A23-A0) to erase one of the three security registers.
ADDRESS
A23-16
A15-12
A11-8
A7-0
Security Register #1
Security Register #2
Security Register #3
00h
00h
00h
0 0 0 1
0 0 1 0
0 0 1 1
0 0 0 0
0 0 0 0
0 0 0 0
Don’t Care
Don’t Care
Don’t Care
The Erase Security Register instruction sequence is shown in Figure 45. The /CS pin must be driven high after
the eighth bit of the last byte has been latched. If this is not done the instruction will not be executed. After /CS
is driven high, the self-timed Erase Security Register operation will commence for a time duration of tSE (See
AC Characteristics). While the Erase Security Register cycle is in progress, the Read Status Register
instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the erase
cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again.
After the Erase Security Register cycle has finished the Write Enable Latch (WEL) bit in the Status Register is
cleared to 0. The Security Register Lock Bits (LB3-1) in the Status Register-2 can be used to OTP protect the
security registers. Once a lock bit is set to 1, the corresponding security register will be permanently locked,
Erase Security Register instruction to that register will be ignored (Refer to section 7.1.8 for detail descriptions).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (44h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 45. Erase Security Registers Instruction
Publication Release Date: June 03, 2016
Revision C
- 50 -
W25Q64JV
Program Security Registers (42h)
The Program Security Register instruction is similar to the Page Program instruction. It allows from one byte
to 256 bytes of security register data to be programmed at previously erased (FFh) memory locations. A Write
Enable instruction must be executed before the device will accept the Program Security Register Instruction
(Status Register bit WEL= 1). The instruction is initiated by driving the /CS pin low then shifting the instruction
code “42h” followed by a 24-bit address (A23-A0) and at least one data byte, into the DI pin. The /CS pin must
be held low for the entire length of the instruction while data is being sent to the device.
ADDRESS
A23-16
A15-12
A11-8
A7-0
Security Register #1
Security Register #2
Security Register #3
00h
00h
00h
0 0 0 1
0 0 1 0
0 0 1 1
0 0 0 0
0 0 0 0
0 0 0 0
Byte Address
Byte Address
Byte Address
The Program Security Register instruction sequence is shown in Figure 46. The Security Register Lock Bits
(LB3-1) in the Status Register-2 can be used to OTP protect the security registers. Once a lock bit is set to 1,
the corresponding security register will be permanently locked, Program Security Register instruction to that
register will be ignored (See 7.1.8, 8.2.25 for detail descriptions).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38 39
CLK
Instruction (42h)
24-Bit Address
Data Byte 1
DI
(IO0)
23 22 21
3
2
1
0
7
6
5
4
3
2
1
0
*
*
= MSB
*
/CS
39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
Mode 3
Mode 0
CLK
Data Byte 2
Data Byte 3
Data Byte 256
DI
(IO0)
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
*
*
*
Figure 46. Program Security Registers Instruction
Publication Release Date: June 03, 2016
Revision C
- 51 -
W25Q64JV
Read Security Registers (48h)
The Read Security Register instruction is similar to the Fast Read instruction and allows one or more data
bytes to be sequentially read from one of the four security registers. The instruction is initiated by driving the
/CS pin low and then shifting the instruction code “48h” followed by a 24-bit address (A23-A0) and eight
“dummy” clocks into the DI pin. The code and address bits are latched on the rising edge of the CLK pin. After
the address is received, the data byte of the addressed memory location will be shifted out on the DO pin at
the falling edge of CLK with most significant bit (MSB) first. The byte address is automatically incremented to
the next byte address after each byte of data is shifted out. Once the byte address reaches the last byte of the
register (byte address FFh), it will reset to address 00h, the first byte of the register, and continue to increment.
The instruction is completed by driving /CS high. The Read Security Register instruction sequence is shown
in Figure 47. If a Read Security Register instruction is issued while an Erase, Program or Write cycle is in
process (BUSY=1) the instruction is ignored and will not have any effects on the current cycle. The Read
Security Register instruction allows clock rates from D.C. to a maximum of FR (see AC Electrical
Characteristics).
ADDRESS
A23-16
A15-12
A11-8
A7-0
Security Register #1
Security Register #2
Security Register #3
00h
00h
00h
0 0 0 1
0 0 1 0
0 0 1 1
0 0 0 0
0 0 0 0
0 0 0 0
Byte Address
Byte Address
Byte Address
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31
CLK
Instruction (48h)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
/CS
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
CLK
Dummy Byte
DI
(IO0)
0
7
6
5
4
3
2
1
0
Data Out 1
Data Out 2
High Impedance
DO
(IO1)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
*
*
Figure 47. Read Security Registers Instruction
Publication Release Date: June 03, 2016
Revision C
- 52 -
W25Q64JV
Individual Block/Sector Lock (36h)
The Individual Block/Sector Lock provides an alternative way to protect the memory array from adverse
Erase/Program. In order to use the Individual Block/Sector Locks, the WPS bit in Status Register-3 must be
set to 1. If WPS=0, the write protection will be determined by the combination of CMP, SEC, TB, BP[2:0] bits
in the Status Registers. The Individual Block/Sector Lock bits are volatile bits. The default values after device
power up or after a Reset are 1, so the entire memory array is being protected.
To lock a specific block or sector as illustrated in Figure 4d, an Individual Block/Sector Lock command must
be issued by driving /CS low, shifting the instruction code “36h” into the Data Input (DI) pin on the rising edge
of CLK, followed by a 24-bit address and then driving /CS high. A Write Enable instruction must be executed
before the device will accept the Individual Block/Sector Lock Instruction (Status Register bit WEL= 1).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (36h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 53. Individual Block/Sector Lock Instruction
Publication Release Date: June 03, 2016
Revision C
- 53 -
W25Q64JV
Individual Block/Sector Unlock (39h)
The Individual Block/Sector Lock provides an alternative way to protect the memory array from adverse
Erase/Program. In order to use the Individual Block/Sector Locks, the WPS bit in Status Register-3 must be
set to 1. If WPS=0, the write protection will be determined by the combination of CMP, SEC, TB, BP[2:0] bits
in the Status Registers. The Individual Block/Sector Lock bits are volatile bits. The default values after device
power up or after a Reset are 1, so the entire memory array is being protected.
To unlock a specific block or sector as illustrated in Figure 4d, an Individual Block/Sector Unlock command
must be issued by driving /CS low, shifting the instruction code “39h” into the Data Input (DI) pin on the rising
edge of CLK, followed by a 24-bit address and then driving /CS high. A Write Enable instruction must be
executed before the device will accept the Individual Block/Sector Unlock Instruction (Status Register bit WEL=
1).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
29 30 31
Mode 3
Mode 0
CLK
Instruction (39h)
24-Bit Address
DI
(IO0)
23 22
2
1
0
*
High Impedance
DO
(IO1)
= MSB
*
Figure 54. Individual Block Unlock Instruction
Publication Release Date: June 03, 2016
Revision C
- 54 -
W25Q64JV
Read Block/Sector Lock (3Dh)
The Individual Block/Sector Lock provides an alternative way to protect the memory array from adverse
Erase/Program. In order to use the Individual Block/Sector Locks, the WPS bit in Status Register-3 must be
set to 1. If WPS=0, the write protection will be determined by the combination of CMP, SEC, TB, BP[2:0] bits
in the Status Registers. The Individual Block/Sector Lock bits are volatile bits. The default values after device
power up or after a Reset are 1, so the entire memory array is being protected.
To read out the lock bit value of a specific block or sector as illustrated in Figure 4d, a Read Block/Sector Lock
command must be issued by driving /CS low, shifting the instruction code “3Dh” into the Data Input (DI) pin on
the rising edge of CLK, followed by a 24-bit address. The Block/Sector Lock bit value will be shifted out on the
DO pin at the falling edge of CLK with most significant bit (MSB) first as shown in Figure 55. If the least
significant bit (LSB) is 1, the corresponding block/sector is locked; if LSB=0, the corresponding block/sector is
unlocked, Erase/Program operation can be performed.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
28 29 30 31 32 33 34 35 36 37 38 39
Mode 3
Mode 0
CLK
Instruction (3Dh)
24-Bit Address
DI
(IO0)
23 22 21
3
2
1
0
*
Lock Value Out
High Impedance
DO
(IO1)
X
X
X
X
X
X
X
0
= MSB
*
*
Figure 55. Read Block Lock Instruction
Publication Release Date: June 03, 2016
Revision C
- 55 -
W25Q64JV
Global Block/Sector Lock (7Eh)
All Block/Sector Lock bits can be set to 1 by the Global Block/Sector Lock instruction. The command must be
issued by driving /CS low, shifting the instruction code “7Eh” into the Data Input (DI) pin on the rising edge of
CLK, and then driving /CS high. A Write Enable instruction must be executed before the device will accept the
Global Block/Sector Lock Instruction (Status Register bit WEL= 1).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (7Eh)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 56. Global Block Lock Instruction for SPI Mode
Global Block/Sector Unlock (98h)
All Block/Sector Lock bits can be set to 0 by the Global Block/Sector Unlock instruction. The command must
be issued by driving /CS low, shifting the instruction code “98h” into the Data Input (DI) pin on the rising edge
of CLK, and then driving /CS high. A Write Enable instruction must be executed before the device will accept
the Global Block/Sector Unlock Instruction (Status Register bit WEL= 1).
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (98h)
High Impedance
DI
(IO0)
DO
(IO1)
Figure 57. Global Block Unlock Instruction for SPI Mode
Publication Release Date: June 03, 2016
Revision C
- 56 -
W25Q64JV
Enable Reset (66h) and Reset Device (99h)
Because of the small package and the limitation on the number of pins, the W25Q64JV provide a software
Reset instruction instead of a dedicated RESET pin. Once the Reset instruction is accepted, any on-going
internal operations will be terminated and the device will return to its default power-on state and lose all the
current volatile settings, such as Volatile Status Register bits, Write Enable Latch (WEL) status,
Program/Erase Suspend status, Read parameter setting (P7-P0), and Wrap Bit setting (W6-W4).
“Enable Reset (66h)” and “Reset (99h)” instructions can be issued in SPI mode. To avoid accidental reset,
both instructions must be issued in sequence. Any other commands other than “Reset (99h)” after the “Enable
Reset (66h)” command will disable the “Reset Enable” state. A new sequence of “Enable Reset (66h)” and
“Reset (99h)” is needed to reset the device. Once the Reset command is accepted by the device, the device
will take approximately tRST=30us to reset. During this period, no command will be accepted.
Data corruption may happen if there is an on-going or suspended internal Erase or Program operation when
Reset command sequence is accepted by the device. It is recommended to check the BUSY bit and the SUS
bit in Status Register before issuing the Reset command sequence.
/CS
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
0
1
2
3
4
5
6
7
Mode 3
Mode 0
CLK
Instruction (66h)
High Impedance
Instruction (99h)
DI
(IO0)
DO
(IO1)
Figure 58. Enable Reset and Reset Instruction Sequence
Publication Release Date: June 03, 2016
Revision C
- 57 -
W25Q64JV
9. ELECTRICAL CHARACTERISTICS
(1)
9.1 Absolute Maximum Ratings
PARAMETERS
SYMBOL
VCC
CONDITIONS
RANGE
UNIT
Supply Voltage
–0.6 to 4.6
V
Voltage Applied to Any Pin
VIO
Relative to Ground
–0.6 to VCC+0.4
V
<20nS Transient
Relative to Ground
Transient Voltage on any Pin
VIOT
–2.0V to VCC+2.0V
V
Storage Temperature
TSTG
TLEAD
VESD
–65 to +150
°C
°C
V
Lead Temperature
See Note (2)
Electrostatic Discharge Voltage
Human Body Model(3) –2000 to +2000
Notes:
1. This device has been designed and tested for the specified operation ranges. Proper operation outside of
these levels is not guaranteed. Exposure to absolute maximum ratings may affect device reliability. Exposure
beyond absolute maximum ratings may cause permanent damage.
2. Compliant with JEDEC Standard J-STD-20C for small body Sn-Pb or Pb-free (Green) assembly and the
European directive on restrictions on hazardous substances (RoHS) 2002/95/EU.
3. JEDEC Std JESD22-A114A (C1=100pF, R1=1500 ohms, R2=500 ohms).
9.2 Operating Ranges
SPEC
PARAMETER
SYMBOL CONDITIONS
UNIT
MIN
3.0
2.7
MAX
3.6
FR = 133MHz,
VCC
fR = 50MHz
fR = 50MHz
V
V
Supply Voltage(1)
FR = 104MHz,
3.0
Ambient Temperature,
Operating
TA
Industrial
–40
+85
°C
Note:
1. VCC voltage during Read can operate across the min and max range but should not exceed ±10% of the
programming (erase/write) voltage.
Publication Release Date: June 03, 2016
- 58 -
Revision C
W25Q64JV
9.3 Power-Up Power-Down Timing and Requirements
SPEC
PARAMETER
SYMBOL
UNIT
MIN
20
5
MAX
VCC (min) to /CS Low
tVSL(1)
tPUW(1)
VWI(1)
µs
ms
V
Time Delay Before Write Instruction
Write Inhibit Threshold Voltage
1.0
2.0
Note:
1. These parameters are characterized only.
VCC
VCC (max)
Program, Erase and Write Instructions are ignored
/CS must track VCC
VCC (min)
VWI
Read Instructions
Allowed
Device is fully
Accessible
tVSL
Reset
State
tPUW
Time
Figure 58a. Power-up Timing and Voltage Levels
/CS must track VCC
during VCC Ramp Up/Down
VCC
/CS
Time
Figure 58b. Power-up, Power-Down Requirement
Publication Release Date: June 03, 2016
Revision C
- 59 -
W25Q64JV
9.4 DC Electrical Characteristics-
SPEC
TYP
PARAMETER
SYMBOL CONDITIONS
UNIT
MAX
MIN
(1)
(1)
Input Capacitance
Output Capacitance
Input Leakage
6
8
pF
pF
µA
µA
CIN
VIN = 0V
(1)
(1)
Cout
ILI
VOUT = 0V
±2
±2
I/O Leakage
ILO
/CS = VCC,
VIN = GND or VCC
Standby Current
ICC1
ICC2
ICC3
10
1
50
15
15
µA
µA
/CS = VCC,
VIN = GND or VCC
Power-down Current
Current Read Data /
C = 0.1 VCC / 0.9 VCC
DO = Open
mA
(2)
Dual /Quad 50MHz
Current Read Data /
Dual /Quad 80MHz
C = 0.1 VCC / 0.9 VCC
DO = Open
ICC3
ICC3
18
20
mA
mA
(2)
Current Read Data /
Dual Output Read/Quad
Output Read 104MHz
C = 0.1 VCC / 0.9 VCC
DO = Open
(2)
Current Write Status
Register
ICC4
ICC5
ICC6
/CS = VCC
/CS = VCC
/CS = VCC
/CS = VCC
20
20
20
20
25
25
25
mA
mA
mA
Current Page Program
Current Sector/Block
Erase
Current Chip Erase
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
ICC7
VIL
25
mA
V
–0.5
VCC x 0.3
VCC + 0.4
0.2
VIH
VCC x 0.7
V
VOL
VOH
IOL = 100 µA
V
IOH = –100 µA
VCC – 0.2
V
Notes:
1. Tested on sample basis and specified through design and characterization data. TA = 25° C, VCC = 3.0V.
2. Checker Board Pattern.
Publication Release Date: June 03, 2016
Revision C
- 60 -
W25Q64JV
9.5 AC Measurement Conditions
SPEC
PARAMETER
SYMBOL
UNIT
MIN
MAX
30
Load Capacitance
CL
TR, TF
VIN
pF
ns
V
Input Rise and Fall Times
Input Pulse Voltages
5
0.1 VCC to 0.9 VCC
0.3 VCC to 0.7 VCC
0.5 VCC to 0.5 VCC
Input Timing Reference Voltages
Output Timing Reference Voltages
IN
V
OUT
V
Note:
1. Output Hi-Z is defined as the point where data out is no longer driven.
Input and Output
Timing Reference Levels
Input Levels
0.9 VCC
0.5 VCC
0.1 VCC
Figure 59. AC Measurement I/O Waveform
Publication Release Date: June 03, 2016
Revision C
- 61 -
W25Q64JV
9.6 AC Electrical Characteristics(6)
SPEC
TYP
DESCRIPTION
SYMBOL
ALT
UNIT
MIN
MAX
Clock frequency except for Read Data (03h)
instructions (3.0V-3.6V)
FR
FR
fC1
fC2
D.C.
133
MHz
Clock frequency except for Read Data (03h)
instructions( 2.7V-3.0V)
D.C.
D.C.
104
50
MHz
MHz
ns
Clock frequency for Read Data instruction (03h)
fR
tCLH,
Clock High, Low Time
for all instructions except for Read Data (03h)
45%
PC
(1)
tCLL
Clock High, Low Time
for Read Data (03h) instruction
tCRLH,
tCRLL
45%
PC
ns
(1)
(2)
Clock Rise Time peak to peak
Clock Fall Time peak to peak
0.1
0.1
V/ns
V/ns
tCLCH
(2)
tCHCL
/CS Active Setup Time relative to CLK
/CS Not Active Hold Time relative to CLK
Data In Setup Time
tSLCH
tCHSL
tDVCH
tCHDX
tCHSH
tSHCH
tSHSL1
tSHSL2
tCSS
5
5
ns
ns
ns
ns
ns
ns
ns
ns
ns
tDSU
tDH
2
Data In Hold Time
3
/CS Active Hold Time relative to CLK
/CS Not Active Setup Time relative to CLK
/CS Deselect Time (for Read)
3
3
tCSH
tCSH
tDIS
10
50
/CS Deselect Time (for Erase or Program or Write)
Output Disable Time
(2)
7
6
tSHQZ
Clock Low to Output Valid
2.7V-3.6V
tCLQV
tCLQX
tV
ns
ns
Output Hold Time
tHO
1.5
Continued – next page AC Electrical Characteristics (cont’d)
Publication Release Date: June 03, 2016
Revision C
- 62 -
W25Q64JV
SPEC
DESCRIPTION
SYMBOL
ALT
UNIT
MIN
TYP
MAX
(2)
/CS High to Power-down Mode
3
3
µs
µs
µs
tDP
(2)
/CS High to Standby Mode without ID Read
/CS High to Standby Mode with ID Read
tRES1
(2)
1.8
tRES2
(2)
/CS High to next Instruction after Suspend
/CS High to next Instruction after Reset
/RESET pin Low period to reset the device
20
30
µs
µs
µs
tSUS
(2)
tRST
1(5)
(2)
tRESET
Write Status Register Time
Page Program Time
tW
10
15
3
ms
ms
tPP
0.8
Sector Erase Time (4KB)
tSE
45
400
ms
Block Erase Time (32KB)
Block Erase Time (64KB)
Chip Erase Time
tBE1
tBE2
tCE
120
150
20
1,600
2,000
100
ms
ms
s
Notes:
1. Clock high or Clock low must be more than or equal to 45%Pc. Pc=1/fC(MAX)
2. Value guaranteed by design and/or characterization, not 100% tested in production.
3. Only applicable as a constraint for a Write Status Register instruction when SRP=1.
4. It’s possible to reset the device with shorter tRESET (as short as a few hundred ns), a 1us minimum is recommended to ensure reliable
operation.
5. Tested on sample basis and specified through design and characterization data. TA = 25° C, VCC = 3.0V, 25% driver strength.
6. 4-bytes address alignment for Quad Read, start address from [A1,A0]=(0,0).
Publication Release Date: June 03, 2016
- 63 -
Revision C
W25Q64JV
9.7 Serial Output Timing
/CS
tCLH
CLK
tCLQV
tCLQX
tCLQV
tCLL
tSHQZ
tCLQX
IO
output
MSB OUT
LSB OUT
9.8 Serial Input Timing
/CS
tSHSL
tSHCH
tCHSL
tSLCH
tCHSH
CLK
tDVCH
tCHDX
tCLCH
tCHCL
IO
input
MSB IN
LSB IN
Publication Release Date: June 03, 2016
Revision C
- 64 -
W25Q64JV
10.PACKAGE SPECIFICATIONS
10.1 8-Pin SOIC 208-mil (Package Code SS)
Millimeters
Symbol
Inches
Nom
Min
Nom
Max
Min
Max
A
A1
A2
b
C
D
D1
E
E1
e
H
L
1.75
0.05
1.70
0.35
0.19
5.18
5.13
5.18
5.13
1.95
0.15
1.80
0.42
0.20
5.28
5.23
5.28
5.23
2.16
0.25
1.91
0.48
0.25
5.38
5.33
5.38
5.33
0.069
0.002
0.067
0.014
0.007
0.204
0.202
0.204
0.202
0.077
0.006
0.071
0.017
0.008
0.208
0.206
0.208
0.206
0.085
0.010
0.075
0.019
0.010
0.212
0.210
0.212
0.210
1.27 BSC
7.90
0.65
0.050 BSC
0.311
0.026
7.70
0.50
8.10
0.80
0.303
0.020
0.319
0.031
y
---
0°
---
---
0.10
8°
---
0°
---
---
0.004
8°
θ
Publication Release Date: June 03, 2016
Revision C
- 65 -
W25Q64JV
10.2 8-Pin VSOP 208-mil (Package Code ST)
θ
θ
Millimeters
Symbol
Inches
Nom
Min
Nom
Max
Min
Max
A
A1
A2
b
c
D
E
E1
e
L
y
θ
―
―
0.10
0.80
0.42
0.127 REF
5.28
7.90
5.28
1.27
0.65
―
1.00
0.15
0.85
0.48
―
―
0.004
0.031
0.017
0.005 REF
0.208
0.311
0.208
0.050
0.026
―
0.039
0.006
0.033
0.019
0.05
0.75
0.35
0.002
0.030
0.014
5.18
7.70
5.18
―
0.50
―
5.38
8.10
5.38
―
0.80
0.10
8°
0.204
0.303
0.204
―
0.020
―
0.212
0.319
0.212
―
0.031
0.004
8°
0°
―
0°
―
Publication Release Date: June 03, 2016
Revision C
- 66 -
W25Q64JV
10.3 8-Pad WSON 6x5-mm (Package Code ZP)
Millimeters
Symbol
Inches
Min
0.70
0.00
Nom
Max
0.80
0.05
Min
0.028
0.000
Nom
0.030
0.001
Max
A
0.75
0.031
0.002
A1
0.02
b
C
0.35
---
0.40
0.20 REF
6.00
0.48
---
0.014
---
0.016
0.008 REF
0.236
0.019
---
D
5.90
3.35
4.90
4.25
6.10
3.45
5.10
4.35
0.232
0.132
0.193
0.167
0.240
0.136
0.201
0.171
D2
E
3.40
0.134
5.00
0.197
E2
e
4.30
0.169
1.27 BSC
0.050 BSC
L
y
0.55
0.00
0.60
---
0.65
0.022
0.000
0.024
---
0.026
0.003
0.075
Note:
The metal pad area on the bottom center of the package is not connected to any internal electrical signals. It can be left
floating or connected to the device ground (GND pin). Avoid placement of exposed PCB vias under the pad.
Publication Release Date: June 03, 2016
- 67 -
Revision C
W25Q64JV
10.4 8-Pad WSON 8x6mm (Package Code ZE)
MILLIMETERS
SYMBOL
INCHES
Min
0.70
0.00
0.35
---
Nom
0.75
Max
0.80
0.05
0.48
---
Min
0.028
0.000
0.014
---
Nom
0.030
Max
A
A1
b
0.031
0.002
0.019
---
0.02
0.001
0.40
0.016
C
0.20 Ref.
8.00
0.008 Ref.
0.315
D
7.90
3.35
5.90
4.25
8.10
3.45
6.10
4.35
0.311
0.132
0.232
0.167
0.319
0.136
0.240
0.171
D2
E
3.40
0.134
6.00
0.236
E2
e
4.30
0.169
1.27 BSC
0.50
0.050 BSC
0.020
L
0.45
0.00
0.55
0.05
0.018
0.000
0.022
0.002
y
---
---
Note:
The metal pad area on the bottom center of the package is not connected to any internal electrical signals. It can be left
floating or connected to the device ground (GND pin). Avoid placement of exposed PCB vias under the pad.
Publication Release Date: June 03, 2016
- 68 -
Revision C
W25Q64JV
10.5 8-Pad XSON 4x4x0.45-mm (Package Code XG)
Publication Release Date: June 03, 2016
Revision C
- 69 -
W25Q64JV
10.6 16-Pin SOIC 300-mil (Package Code SF)
Millimeters
Symbol
Inches
Nom
0.098
---
Min
2.36
0.10
---
Nom
2.49
---
Max
2.64
0.30
---
Min
0.093
0.004
---
Max
A
A1
A2
b
0.104
0.012
---
2.31
0.41
0.23
10.31
10.31
7.49
1.27 BSC
0.81
---
0.091
0.016
0.009
0.406
0.406
0.295
0.050 BSC
0.032
---
0.33
0.18
10.08
10.01
7.39
0.51
0.28
10.49
10.64
7.59
0.013
0.007
0.397
0.394
0.291
0.020
0.011
0.413
0.419
0.299
C
D
E
E1
e
L
0.38
---
1.27
0.076
8°
0.015
---
0.050
0.003
8°
y
θ
0°
---
0°
---
Publication Release Date: June 03, 2016
Revision C
- 70 -
W25Q64JV
10.8 8-Pin PDIP 300-mil (Package Code DA)
p
d
w
Millimeters
Symbol
Inches
Nom
Min
Nom
Max
Min
Max
A
A1
A2
D
---
---
---
5.33
---
---
---
---
0.210
---
0.38
3.18
9.02
0.015
0.125
0.355
3.30
9.27
7.62 BSC
6.35
3.30
9.02
7°
3.43
10.16
0.130
0.365
0.300 BSC
0.250
0.130
0.355
7°
0.135
0.400
E
E1
L
6.22
2.92
8.51
0°
6.48
3.81
9.53
15°
---
0.245
0.115
0.335
0°
0.255
0.150
0.375
15°
eB
θ°
d
---
2.54
1.52
0.46
---
0.100
0.060
0.018
---
w
---
---
---
---
p
---
---
---
---
Publication Release Date: June 03, 2016
Revision C
- 71 -
W25Q64JV
10.10 24-Ball TFBGA 8x6-mm (Package Code TB, 5x5 Ball Array)
Note:
Ball land: 0.45mm. Ball Opening: 0.35mm
PCB ball land suggested <= 0.35mm
Millimeters
Nom
---
Inches
Nom
Symbol
Min
---
Max
1.20
0.36
---
Min
---
Max
A
A1
A2
b
---
0.047
0.014
---
0.26
---
0.31
0.010
---
0.012
0.85
0.033
0.35
7.90
0.40
0.45
8.10
0.014
0.311
0.016
0.018
0.319
D
8.00
0.315
D1
E
4.00 BSC
6.00
0.157 BSC
0.236
5.90
6.10
0.10
0.232
0.240
E1
SE
SD
e
4.00 BSC
1.00 TYP
1.00 TYP
1.00 BSC
---
0.157 BSC
0.039 TYP
0.039 TYP
0.039 BSC
---
ccc
---
---
0.0039
Publication Release Date: June 03, 2016
Revision C
- 72 -
W25Q64JV
10.11 24-Ball TFBGA 8x6-mm (Package Code TC, 6x4 ball array)
Note:
Ball land: 0.45mm. Ball Opening: 0.35mm
PCB ball land suggested <= 0.35mm
Millimeters
Nom
---
Inches
Nom
Symbol
Min
---
Max
1.20
0.35
0.45
8.05
Min
---
Max
A
A1
b
---
0.047
0.014
0.018
0.317
0.25
0.35
7.95
0.30
0.010
0.014
0.313
0.012
0.40
0.016
D
8.00
0.315
D1
E
5.00 BSC
6.00
0.197 BSC
0.236
5.95
---
6.05
0.10
0.234
---
0.238
0.039
E1
e
3.00 BSC
1.00 BSC
---
0.118 BSC
0.039 BSC
---
ccc
Publication Release Date: June 03, 2016
Revision C
- 73 -
W25Q64JV
11. ORDERING INFORMATION
(1)
(2)
W 25Q 64J V xx I
W
= Winbond
25Q
64J
= SpiFlash Serial Flash Memory with 4KB sectors, Dual/Quad I/O
=
64M-bit
V
= 2.7V to 3.6V
SS = 8-pin SOIC 208-mil
DA = 8-pin PDIP 300-mil
XG = XSON 4x4x0.45-mm
ST = 8-pin VSOP 208-mil
ZP = WSON8 6x5-mm
TB = TFBGA 8x6-mm (5x5 ball array)
SF = 16-pin SOIC 300-mil
ZE = WSON8 8x6-mm
TC = TFBGA 8x6-mm (6x4 ball array)
I
=
Industrial (-40°C to +85°C)
(3,4)
Q
=
Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb2O3)
with QE = 1 in Status register-2
Notes:
1. The “W” prefix is not included on the part marking.
2. Only the 2nd letter is used for the part marking; WSON package type ZP is not used for the part marking.
3. Standard bulk shipments are in Tube (shape E). Please specify alternate packing method, such as Tape and Reel
(shape T) or Tray (shape S), when placing orders.
4. For shipments with OTP feature enabled, please specify when placing orders.
Publication Release Date: June 03, 2016
- 74 -
Revision C
W25Q64JV
11.1 Valid Part Numbers and Top Side Marking
The following table provides the valid part numbers for the W25Q64JV SpiFlash Memory. Please contact
Winbond for specific availability by density and package type. Winbond SpiFlash memories use a 12-digit
Product Number for ordering. However, due to limited space, the Top Side Marking on all packages uses an
abbreviated 10-digit number.
PACKAGE TYPE
DENSITY
64M-bit
64M-bit
64M-bit
64M-bit
PRODUCT NUMBER
W25Q64JVSSIQ
W25Q64JVSTIQ
W25Q64JVSFIQ
W25Q64JVDAIQ
TOP SIDE MARKING
25Q64JVSIQ
SS
SOIC-8 208-mil
ST(1)
VSOP-8 208-mil
SF
SOIC-16 300-mil
DA
PDIP-8 300-mil
25Q64JVTIQ
25Q64JVFIQ
25Q64JVAIQ
ZP(1)
WSON-8 6x5-mm
ZE(1)
WSON-8 8x6-mm
64M-bit
64M-bit
W25Q64JVZPIQ
W25Q64JVZEIQ
25Q64JVIQ
25Q64JVIQ
XG
XSON-8
4x4x0.45-mm
64M-bit
64M-bit
64M-bit
W25Q64JVXGIQ
W25Q64JVTBIQ
W25Q64JVTCIQ
Q64JVXGIQ
25Q64JVBIQ
25Q64JVCIQ
TB(2)
TFBGA-24 8x6-mm
(5x5 Ball Array)
TC(2)
TFBGA-24 8x6-mm
(6x4 Ball Array)
Note:
1. For WSON packages, the package type ZP and ZE is not used in the top side marking.
2. These package types are special order, please contact Winbond for more information.
Publication Release Date: June 03, 2016
Revision C
- 75 -
W25Q64JV
12. REVISION HISTORY
VERSION
DATE
PAGE
DESCRIPTION
New Create Datasheet
A
B
2015/01/07
2016/04/12
Removed “Preliminary”
16
73-76
Updated QE description
Added TFBGA information
C
2016/06/03
Trademarks
Winbond and SpiFlash are trademarks of Winbond Electronics Corporation.
All other marks are the property of their respective owner.
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components in systems or
equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship
instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other
applications intended to support or sustain life. Furthermore, Winbond products are not intended for
applications wherein failure of Winbond products could result or lead to a situation wherein personal injury,
death or severe property or environmental damage could occur. Winbond customers using or selling these
products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any
damages resulting from such improper use or sales.
Information in this document is provided solely in connection with Winbond products. Winbond
reserves the right to make changes, corrections, modifications or improvements to this document and
the products and services described herein at any time, without notice.
Publication Release Date: June 03, 2016
- 76 -
Revision C
相关型号:
©2020 ICPDF网 联系我们和版权申明