5962-9318701HXX [WEDC]
SRAM Module, 512KX8, 120ns, CMOS, CHIP66;
| 型号： | 5962-9318701HXX |
| 厂家： | 
WHITE ELECTRONIC DESIGNS CORPORATION |
| 描述： | SRAM Module, 512KX8, 120ns, CMOS, CHIP66 静态存储器 |
| 文件： | 总34页 (文件大小：226K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
B
Added device type 10. Redrew entire document.
95-07-07
95-10-18
K. A. Cottongim
K. A. Cottongim
Corrected true dimensioning table and removed dimensions A2 and F
in figure 1. Changed dimension A min from 0.185 inches to 0.180
inches for case outlines U and Y. Changes dimension A min from
0.210 inches to 0.200 inches for case outlines T and X. Added
vendor CAGE code 88379 for device types 01 through 10. Made
editorial changes throughout.
C
D
Added case outlines M, N, 4, and 5. Redrew entire document.
Table I, changed the maximum limit for the supply current 32-bit
mode test (ICC32) from 440 to 520 for device types 05 and 06, and
from 500 to 520 for device types 07 and 08. -sld
96-11-20
97-09-08
K. A. Cottongim
K. A. Cottongim
E
F
Figure 1: For case outlines 4 and 5 changed the dimension D3 min
and max limits to 1.020 and 1.060 inches. For case outlines 4 and 5
changed dimension A min limit to .135 inches. For case outlines 4
and 5 changed dimension L min limit to .132 inches. -sld
Table I; changed the max limit for ICC32 for device types 05, 06, 07,
and 08 from 520 mA to 600 mA. Changed the max limit for ICCDR1 for
device types 05 through 10 from 10.4 mA to 11.6 mA. -sld
Added device type 11. Added vendor CAGE 0EU86 for device types
05 through 09. -sld
Figure 1; changed the maximum limit for dimension D3 from 1.060
inches to 1.086 inches for case outlines 4 and 5. -sld
Added note to paragraph 1.2.2 and table I regarding the 4 transistor
design. Added footnote 3 for case outlines U, T, X, and Y on the
bulletin page. Redrew entire document. -sld
98-04-06
98-07-13
K. A. Cottongim
K. A. Cottongim
G
H
J
99-08-27
00-02-07
00-11-14
Raymond Monnin
Raymond Monnin
Raymond Monnin
K
L
Added device types 12 through 18. -sld
Updated drawing. -gz
01-11-13
07-04-16
Raymond Monnin
Robert M. Heber
REV
SHEET
REV
L
L
L
L
L
L
L
21
L
L
22
L
L
23
L
L
24
L
L
25
L
L
26
L
SHEET
15
16
17
18
19
20
REV STATUS
OF SHEETS
REV
L
7
L
8
L
9
L
L
L
L
L
SHEET
1
2
3
4
5
6
10
11
12
13
14
PMIC N/A
PREPARED BY
Steve L. Duncan
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil/
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Michael C. Jones
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
Kendall A. Cottongim
MICROCIRCUIT, HYBRID, DIGITAL, STATIC
RANDOM ACCESS MEMORY, CMOS, 128K x
32-BIT
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
94-06-24
AMSC N/A
REVISION LEVEL
SIZE
A
CAGE CODE
5962-93187
67268
L
SHEET
1 OF 26
DSCC FORM 2233
APR 97
5962-E344-07
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
-
93187
01
H
M
X
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
⏐
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
/
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type 1/
Generic number
Circuit function
Access time
01
02
03
04
05,12
WS128K32-120HQ, ACT-S128K32-120PQ
WS128K32-100HQ, ACT-S128K32-100PQ
WS128K32-85HQ, ACT-S128K32-85PQ
WS128K32-70HQ, ACT-S128K32-70PQ
WS128K32-55HQ, ACT-S128K32-55PQ,
AS8S128K32P-55
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
120 ns
100 ns
85 ns
70 ns
55 ns
06,13
07,14
08,15
09,16
10,17
11,18
WS128K32-45HQ, ACT-S128K32-45PQ,
AS8S128K32P-45
WS128K32-35HQ, ACT-S128K32-35PQ,
AS8S128K32P-35
WS128K32-25HQ, ACT-S128K32-25PQ,
AS8S128K32P-25
WS128K32-20HQ, ACT-S128K32-20PQ,
AS8S128K32P-20
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
45 ns
35 ns
25 ns
20 ns
17 ns
15 ns
WS128K32-17HQ, ACT-S128K32-17PQ,
AS8S128K32P-17
WS128K32-15HQ
_____
1/ Due to the nature of the 4 transistor design of the die in these device types, topologically pure testing is important,
particularly for high reliability applications. The device manufacturer should be consulted concerning their testing
methods and algorithms.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
2
DSCC FORM 2234
APR 97
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All
levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and
E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
K
Device performance documentation
Highest reliability class available. This level is intended for use in space
applications.
H
G
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C and D).
E
D
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: 1/
Outline letter
Descriptive designator
Terminals
Package style
M
N
T
U
X
Y
4
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
66
66
66
66
66
66
66
66
Hex-in-line, single cavity, without standoffs
Hex-in-line, single cavity, without standoffs
Hex-in-line, single cavity, with standoffs
Hex-in-line, single cavity, without standoffs
Hex-in-line, single cavity, with standoffs
Hex-in-line, single cavity, without standoffs
Hex-in-line, single cavity, with standoffs
Hex-in-line, single cavity, with standoffs
5
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 2/
Supply voltage range (VCC)........................................................
Signal voltage range (any pin) ...................................................
Power dissipation (PD):
-0.5 V dc to +7.0 V dc
-0.5 V dc to +7.0 V dc
Device types 01 through 08, and 12 through 15.....................
Device types 09, 10, 11, 16, 17, and 18 ................................
Thermal resistance junction-to-case (θJC) .................................
Storage temperature range........................................................
Lead temperature (soldering, 10 seconds).................................
2.2 W
4.4 W
6.6°C/W
-65°C to +150°C
+300°C
1/ Additional case outlines are available on Standard Microcircuit Drawing 5962-95595.
2/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
3
DSCC FORM 2234
APR 97
1.4 Recommended operating conditions.
Supply voltage range (VCC)........................................................
Input low voltage range (VIL) ......................................................
Input high voltage range (VIH) ....................................................
Output low voltage, maximum (VOL)...........................................
Output high voltage, minimum (VOH)..........................................
Case operating temperature range (TC).....................................
+4.5 V dc to +5.5 V dc
-0.5 V dc to +0.8 V dc
+2.2 V dc to VCC +0.3 V dc
+0.4 V dc
+2.4 V dc
-55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or from
the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38534 and herein.
SIZE
STANDARD
5962-93187
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
4
DSCC FORM 2234
APR 97
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3.
3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4 and 5.
3.2.5 Block diagram. The block diagram shall be as specified on figure 6.
3.2.6 Output load circuit. The output load circuit shall be as specified on figure 7.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DSCC-VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets
the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
SIZE
STANDARD
5962-93187
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
Group A
subgroups
Device
types
Limits
Unit
VSS = 0 V dc
Min
Max
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
DC PARAMETERS
Supply current,
32-bit mode
ICC32
1,2,3
1,2,3
01-04
05-18
120
600
mA
CS = VIL, OE = VIH,
f = 5 MHz CMOS compatible
VCC = +5.5 V dc
Standby current
ISB
01,02
03,04
2.4
5.0
60
mA
CS = VCC, OE = VIH,
f = 5 MHz CMOS compatible
VCC = +5.5 V dc
05-08,
12-15
09-11,
16-18
80
10
Input leakage current
Output leakage current
ILI
VCC = +5.5 V dc,
1,2,3
1,2,3
All
µA
µA
VIN = GND or VCC
ILO
All
10
CS = VIH, OE = VIH,
VOUT = GND or VCC
Output low voltage
Output high voltage
DATA RETENTION
VOL
VCC = +4.5 V dc, IOL = +2.1
mA
1,2,3
01-07,
12-14
0.4
V
VCC = +4.5 V dc, IOL = +8.0
mA
08-11,
15-18
0.4
VOH
VCC = +4.5 V dc, IOH = -1.0
mA
1,2,3
01-07,
12-14
2.4
V
VCC = +4.5 V dc, IOH = -4.0
mA
08-11,
15-18
2.4
2.0
Data retention supply
voltage
VDR
1,2,3
1,2,3
All
5.5
V
CS ≥ VCC - 0.2 V dc
Data retention current
ICCDR1
VCC = +3.0 V dc
01-04
1.6
mA
05-11,
18
11.6
12-17
20.0
See footnotes at end of table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
Group A
subgroups
Device
types
Limits
Unit
VSS = 0 V dc
Min
Max
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
CAPACITANCE
COE
CWE
CCS
CI/O
CAD
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
4
4
4
4
4
All
All
All
All
All
500
20
20
20
50
pF
OE capacitance 3/
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
pF
pF
pF
pF
WE 1-4 capacitance 3/
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
CS 1-4 capacitance 3/
D0 - D31 capacitance 3/
A0 - A16 capacitance 3/
VI/O =0 V dc, f = 1.0 MHz,
TA = +25°C
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
FUNCTIONAL TESTING
Functional tests
See 4.3.1c
7,8A,8B
9,10,11
All
READ CYCLE AC TIMING
Read cycle time
tRC
See figure 4
01
120
100
85
70
55
45
35
25
20
17
15
ns
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
See footnotes at end of table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
7
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
Group A
subgroups
Device
types
Limits
Unit
VSS = 0 V dc
Min
Max
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
READ CYCLE AC TIMING - Continued.
Address access time
tAA
See figure 4
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
120
100
85
70
55
45
35
25
20
17
15
ns
Output hold from address
change
tOH
See figure 4
See figure 4
9,10,11
9,10,11
01-04
05-18
5
0
ns
ns
Chip select access time
tACS
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
120
100
85
70
55
45
35
25
20
17
15
Output enable to output
valid
tOE
See figure 4
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,11
17,18
60
50
45
35
30
25
20
15
12
10
10
ns
Chip select to output in
low impedance 3/
tCLZ
See figure 4
9,10,11
01-04
5
3
ns
05-18
See footnotes at end of table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
8
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
Group A
subgroups
Device
types
Limits
Unit
VSS = 0 V dc
Min
Max
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
READ CYCLE AC TIMING - Continued.
Output enable to output in
low impedance 3/
tOLZ
See figure 4
See figure 4
9,10,11
9,10,11
01-04
05-18
5
0
ns
Chip select to output
in high impedance 3/
tCHZ
01,02
03,04
05-07
08-11
12-14
15-18
35
25
20
12
20
12
ns
ns
Output enable to output
in high impedance 3/
tOHZ
See figure 4
9,10,11
01,02
03,04
05-07
08-11
12-14
15-18
35
25
20
12
20
12
WRITE CYCLE AC TIMING
Write cycle time
tWC
See figure 5
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
120
100
85
70
55
45
35
25
20
17
15
ns
Chip select to end of write
tCW
See figure 5
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
100
80
75
60
45
30
25
25
20
15
14
ns
See footnotes at end of table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
9
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
Group A
subgroups
Device
types
Limits
Unit
VSS = 0 V dc
Min
Max
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
WRITE CYCLE AC TIMING - Continued.
Address select to end of
write
tAW
See figure 5
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,10
16,17
11,18
100
80
75
60
45
30
25
20
15
15
14
ns
Data valid to end of write
tDW
See figure 5
9,10,11
01
02
03
04
05,06
12,13
07,14
08,15
09,16
10,11
17,18
50
40
35
30
25
25
20
15
12
10
10
ns
Address setup time
Write pulse width
tAS
See figure 5
See figure 5
9,10,11
9,10,11
01-04
5.0
ns
ns
05-18
0
tWP
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,11
17,18
80
70
55
50
45
30
25
20
15
14
14
See footnotes at end of table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
10
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
Group A
subgroups
Device
types
Limits
Unit
VSS = 0 V dc
Min
Max
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
WRITE CYCLE AC TIMING - Continued.
Write to output 3/
in high impedance
tWHZ
See figure 5
9,10,11
01,02
03-06
12,13
07,14
08,15
09,16
10,11
17,18
35
25
25
20
15
12
10
10
ns
Address hold time
tAH
See figure 5
See figure 5
9,10,11
9,10,11
01-04
5
ns
ns
05-18
01-04
0
5
4
Output active from end of
write
tOW
05,06,
07,12,
13,14
08,09,
10,11,
15,16,
17,18
3
0
Data hold time
tDH
See figure 5
9,10,11
All
ns
1/ Unless otherwise specified, the AC test conditions are as follows:
Input pulse levels: V = 0 V and V = 3.0 V
IL
IH
Input rise and fall times: 5 nanoseconds
Input and output timing reference level: 1.5 V, ±0.5 V
Output loading: see figure 7.
2/ Due to the nature of the 4 transistor design of the die used in these device types, topologically pure testing is important,
particularly for high reliability applications. The device manufacturer should be consulted concerning their testing
methods and algorithms.
3/ Guaranteed by design, but not tested.
SIZE
STANDARD
5962-93187
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
11
DSCC FORM 2234
APR 97
Case outlines M and N.
FIGURE 1. Case outline(s).
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
12
DSCC FORM 2234
APR 97
Case outlines M and N - Continued.
Symbol
Millimeters
Inches
Min
3.30
0.13
0.41
Max
4.09
0.50
0.51
Min
.130
.005
.016
Max
.159
.020
.020
A
A1
φb
0.76 REF
.030 REF
φb1
φb2
D/E
D1/E1
D2
D3
e
1.65
1.91
.065
.075
27.02
27.58
1.064
1.086
25.40 BSC
15.24 BSC
1.000 BSC
.600 BSC
26.16
26.42
1.030
1.040
.100 BSC
2.54 BSC
L
4.19
4.69
.165
.185
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin 1 is identified by a .070 inch (1.78 mm) square pad.
3. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
5962-93187
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
13
DSCC FORM 2234
APR 97
Case outlines T, X, 4, and 5.
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
14
DSCC FORM 2234
APR 97
Case outlines T and X - Continued.
Symbol
Millimeters
Inches
Min
5.08
0.64
0.41
1.14
1.65
29.72
Max
6.22
0.89
0.51
1.40
1.91
30.48
Min
.200
.025
.016
.045
.065
1.170
Max
.245
.035
.020
.055
.075
1.200
A
A1
φb
φb1
φb2
D/E
D1/E1
D2
D3
e
25.40 BSC
15.24 BSC
28.96 29.21
2.54 BSC
1.000 BSC
.600 BSC
1.140
1.150
.100 BSC
L
3.68
3.94
.145
.155
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin 1 is identified by a .070 inch (1.78 mm) square pad.
3. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
5962-93187
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
15
DSCC FORM 2234
APR 97
Case outlines 4 and 5 - Continued.
Symbol
Millimeters
Inches
Min
3.43
0.64
0.41
1.14
1.65
27.02
Max
4.95
0.89
0.51
1.40
1.91
27.58
Min
.135
.025
.016
.045
.065
1.064
Max
.195
.035
.020
.055
.075
1.086
A
A1
φb
φb1
φb2
D/E
D1/E1
D2
D3
e
25.40 BSC
15.24 BSC
25.91 27.58
2.54 BSC
1.000 BSC
.600 BSC
1.020
1.086
.100 BSC
L
3.35
3.94
.132
.155
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin 1 is identified by a .060 inch ( 1.52 mm) square pad.
3. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
5962-93187
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
16
DSCC FORM 2234
APR 97
Case outlines U and Y.
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
17
DSCC FORM 2234
APR 97
Case outlines U and Y - Continued.
Symbol
Millimeters
Inches
Min
4.57
0.13
0.41
0.76
1.65
29.72
Max
5.84
0.50
0.51
1.52
1.91
30.48
Min
.180
.005
.016
.030
.065
1.170
Max
.230
.020
.020
.060
.075
1.200
A
A1
φb
φb1
φb2
D/E
D1/E1
D2
D3
e
25.40 BSC
15.24 BSC
28.96 29.21
2.54 BSC
1.000 BSC
.600 BSC
1.140
1.150
.100 BSC
L
4.19
4.69
.165
.185
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin 1 is identified by a .070 inch (1.78 mm) square pad.
3. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
SIZE
STANDARD
5962-93187
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
18
DSCC FORM 2234
APR 97
Device
types
All
Device
types
All
Device
types
All
Device
types
All
Case
outlines
M,N,T,U,X,
Y,4,5
Case
outlines
M,N,T,U,X,
Y,4,5
Case
outlines
M,N,T,U,X,
Y,4,5
Case
outlines
M,N,T,U,X,
Y,4,5
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
WE 3
CS 3
GND
I/O19
I/O31
I/O30
I/O29
I/O28
A0
1
2
I/O8
I/O9
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
A12
VCC
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
I/O25
I/O26
A6
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
CS 1
3
I/O10
A13
4
See note
I/O3
A7
5
A14
See note
A8
6
A15
I/O15
I/014
I/O13
I/O12
OE
7
A16
A9
8
See Note
I/O0
I/O16
I/O17
I/O18
VCC
9
10
11
12
13
14
15
16
17
I/O1
A1
I/O2
See note
WE 1
A2
WE 2
CS 2
CS 4
WE 4
I/O23
I/O22
I/O21
I/O20
I/O7
I/O6
I/O5
I/O4
I/O24
GND
I/O11
A10
I/O27
A3
A4
A11
A5
NOTE:
1. Case outlines M, T, U, and 4, pins 8, 21, 28, and 39 are no connects and for case outlines N, X, Y, and 5, pins 8, 21, 28,
and 39 are grounds.
FIGURE 2. Terminal connections.
SIZE
STANDARD
5962-93187
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
19
DSCC FORM 2234
APR 97
CS
OE
WE
Mode
Data I/O
Power
H
L
L
L
X
L
X
H
H
L
Standby
Read
High Z
Data Out
High Z
Standby (deselect/power down)
Active
Active (deselect)
Active
H
X
Output disable
Write
Data In
NOTES:
1. H = V = High logic level
IH
2. L = V = Low logic level
IL
3. X = Do not care (either high or low)
4. High Z = High impedance state
FIGURE 3. Truth table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
20
DSCC FORM 2234
APR 97
NOTE: Guaranteed by design, but not tested.
FIGURE 4. Read cycle timing diagram.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
21
DSCC FORM 2234
APR 97
NOTE: Guaranteed by design, but not tested.
FIGURE 5. Write cycle timing diagram.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
22
DSCC FORM 2234
APR 97
FIGURE 6. Block diagram.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
23
DSCC FORM 2234
APR 97
Parameter
Input Pulse Level
Typ.
0 - 3.0
5
Unit
V
Input Rise and Fall
ns
V
Input and Output Reference Level
Output Load Capacitance
1.5
50
pf
NOTES:
1. VZ is programmable from -2 V to +7 V.
2. IOL and IOH are programmable from 0 to 16mA.
3. Tester impedance is ZO = 75Ω.
4. VZ is typically the midpoint of VOH and VOL
.
5. IOL and IOH are adjusted to simulate a typical resistive load circuit.
6. ATE tester includes jig capacitance.
FIGURE 7. Output load circuit.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-93187
A
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
24
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group A
test table)
Interim electrical parameters
Final electrical parameters
Group A test requirements
1,4,7,9
1*,2,3,4,7,8A,8B,9,10,11
1,2,3,4,7,8A,8B,9,10,11
1,2,3,4,7,8A,8B,9,10,11
Group C end-point electrical
parameters
End-point electrical parameters
for Radiation Hardness Assurance
(RHA) devices
Not applicable
* PDA applies to subgroup 1.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1015 of MIL-STD-883.
(2)
T as specified in accordance with table I of method 1015 of MIL-STD-883.
A
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. Tests shall be as specified in table II herein.
b. Subgroups 5 and 6 shall be omitted.
c. Subgroups 7 and 8 shall include verification of the truth table on figure 3.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
SIZE
STANDARD
5962-93187
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
25
DSCC FORM 2234
APR 97
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test, method 1005 of MIL-STD-883.
(1) Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1005 of MIL-STD-883.
(2)
T as specified in accordance with table I of method 1005 of MIL-STD-883.
A
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF-
38534.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system
application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used
for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962)
should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614)
692-1081.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103
and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DSCC-VA and have agreed to this drawing.
SIZE
STANDARD
5962-93187
A
MICROCIRCUIT DRAWING
REVISION LEVEL
SHEET
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
L
26
DSCC FORM 2234
APR 97
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 07-04-16
Approved sources of supply for SMD 5962-93187 are listed below for immediate acquisition information only and shall
be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded
by the next dated revisions of MIL-HDBK-103 and QML-38534. DSCC maintains an online database of all current
sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
cage
number
Vendor
similar
PIN 2/
5962-9318701HTA
5962-9318701HTA
5962-9318701HUA
5962-9318701HUA
5962-9318701HXA
5962-9318701HXA
5962-9318701HYA
5962-9318701HYA
5962-9318701H4A
5962-9318701H4C
5962-9318701H5A
5962-9318701H5C
5962-9318702HTA
5962-9318702HTA
5962-9318702HUA
5962-9318702HUA
5962-9318702HXA
5962-9318702HXA
5962-9318702HYA
5962-9318702HYA
5962-9318702H4A
5962-9318702H4C
5962-9318702H4A
5962-9318702H5C
5962-9318703HTA
5962-9318703HTA
5962-9318703HUA
5962-9318703HUA
5962-9318703HXA
5962-9318703HXA
5962-9318703HYA
5962-9318703HYA
5962-9318703H4A
5962-9318703H4C
5962-9318703H5A
5962-9318703H5C
3/
3/
3/
3/
3/
3/
3/
3/
54230
54230
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
54230
54230
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
WS128K32N-120HQ
ACT-S128K32N-120P2Q
WS128K32N-120HSQ
ACT-S128K32N-120P6Q
WS128K32-120HQ
ACT-S128K32C-120P2Q
WS128K32-120HSQ
ACT-S128K32C-120P6Q
WS128K32N-120H1Q
WS128K32N-120H1Q
WS128K32-120H1Q
WS128K32-120H1Q
WS128K32N-100HQ
ACT-S128K32N-100P2Q
WS128K32N-100HSQ
ACT-S128K32N-100P6Q
WS128K32-100HQ
ACT-S128K32C-100P2Q
WS128K32-100HSQ
ACT-S128K32C-100P6Q
WS128K32N-100H1Q
WS128K32N-100H1Q
WS128K32-100H1Q
WS128K32-100H1Q
WS128K32N-85HQ
ACT-S128K32N-085P2Q
WS128K32N-85HSQ
ACT-S128K32N-085P6Q
WS128K32-85HQ
ACT-S128K32C-085P2Q
WS128K32-85HSQ
ACT-S128K32C-085P6Q
WS128K32N-85H1Q
WS128K32N-85H1Q
WS128K32-85H1Q
54230
54230
54230
54230
WS128K32-85H1Q
See footnotes at end of table.
1 of 8
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9318704HTA
5962-9318704HTA
5962-9318704HUA
5962-9318704HUA
5962-9318704HXA
5962-9318704HXA
5962-9318704HYA
5962-9318704HYA
5962-9318704H4A
5962-9318704H4C
5962-9318704H5A
5962-9318704H5C
5962-9318705HMA
5962-9318705HNA
5962-9318705HTA
5962-9318705HTA
5962-9318705HUA
5962-9318705HUA
5962-9318705HXA
5962-9318705HXA
5962-9318705HYA
5962-9318705HYA
5962-9318705H4A
5962-9318705H4C
5962-9318705H4A
5962-9318705H4C
5962-9318705H4A
5962-9318705H5A
5962-9318705H5C
5962-9318705H5A
5962-9318705H5C
5962-9318705H5A
5962-9318706HMA
5962-9318706HNA
5962-9318706HTA
5962-9318706HTA
5962-9318706HUA
5962-9318706HUA
5962-9318706HXA
5962-9318706HXA
5962-9318706HYA
5962-9318706HYA
5962-9318706H4A
5962-9318706H4C
5962-9318706H4A
5962-9318706H4C
5962-9318706H4A
5962-9318706H5A
5962-9318706H5C
5962-9318706H5A
5962-9318706H5C
5962-9318706H5A
3/
3/
3/
3/
3/
3/
3/
3/
54230
54230
54230
54230
3/
3/
3/
3/
3/
WS128K32N-70HQ
ACT-S128K32N-070P2Q
WS128K32N-70HSQ
ACT-S128K32N-070P6Q
WS128K32-70HQ
ACT-S128K32C-070P2Q
WS128K32-70HSQ
ACT-S128K32C-070P6Q
WS128K32N-70H1Q
WS128K32N-70H1Q
WS128K32-70H1Q
WS128K32-70H1Q
ACT-S128K32N-055P3Q
ACT-S128K32C-055P3Q
WS128K32N-55HQ
ACT-S128K32N-055P2Q
WS128K32N-55HSQ
ACT-S128K32N-055P6Q
WS128K32-55HQ
3/
3/
3/
3/
ACT-S128K32C-055P2Q
WS128K32-55HSQ
3/
ACT-S128K32C-055P6Q
AS8S128K32PN-55/883C
AS8S128K32PN-55/883C
WS128K32N-55H1Q
WS128K32N-55H1Q
ACT-S128K32N-055P7Q
AS8S128K32P-55/883C
AS8S128K32P-55/883C
WS128K32-55H1Q
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
3/
WS128K32-55H1Q
ACT-S128K32C-055P7Q
ACT-S128K32N-045P3Q
ACT-S128K32C-045P3Q
WS128K32N-45HQ
ACT-S128K32N-045P2Q
WS128K32N-45HSQ
ACT-S128K32N-045P6Q
WS128K32-45HQ
ACT-S128K32C-045P2Q
WS128K32-45HSQ
3/
3/
ACT-S128K32C-045P6Q
AS8S128K32PN-45/883C
AS8S128K32PN-45/883C
WS128K32N-45H1Q
WS128K32N-45H1Q
ACT-S128K32N-045P7Q
AS8S128K32P-45/883C
AS8S128K32P-45/883C
WS128K32-45H1Q
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
WS128K32-45H1Q
ACT-S128K32C-045P7Q
See footnotes at end of table.
2 of 8
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9318707HMA
5962-9318707HNA
5962-9318707HTA
5962-9318707HTA
5962-9318707HUA
5962-9318707HUA
5962-9318707HXA
5962-9318707HXA
5962-9318707HYA
5962-9318707HYA
5962-9318707H4A
5962-9318707H4C
5962-9318707H4A
5962-9318707H4C
5962-9318707H4A
5962-9318707H5A
5962-9318707H5C
5962-9318707H5A
5962-9318707H5C
5962-9318707H5A
5962-9318708HMA
5962-9318708HNA
5962-9318708HTA
5962-9318708HTA
5962-9318708HUA
5962-9318708HUA
5962-9318708HXA
5962-9318708HXA
5962-9318708HYA
5962-9318708HYA
5962-9318708H4A
5962-9318708H4C
5962-9318708H4A
5962-9318708H4C
5962-9318708H4A
5962-9318708H5A
5962-9318708H5C
5962-9318708H5A
5962-9318708H5C
5962-9318708H5A
3/
3/
3/
3/
3/
3/
3/
3/
3/
ACT-S128K32N-035P3Q
ACT-S128K32C-035P3Q
WS128K32N-35HQ
ACT-S128K32N-035P2Q
WS128K32N-35HSQ
ACT-S128K32N-035P6Q
WS128K32-35HQ
ACT-S128K32C-035P2Q
WS128K32-35HSQ
ACT-S128K32C-035P6Q
AS8S128K32PN-35/883C
AS8S128K32PN-35/883C
WS128K32N-35H1Q
3/
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
3/
WS128K32N-35H1Q
ACT-S128K32N-035P7Q
AS8S128K32P-35/883C
AS8S128K32P-35/883C
WS128K32-35H1Q
WS128K32-35H1Q
ACT-S128K32C-035P7Q
ACT-S128K32N-025P3Q
ACT-S128K32C-025P3Q
WS128K32N-25HQ
ACT-S128K32N-025P2Q
WS128K32N-25HSQ
ACT-S128K32N-025P6Q
WS128K32-25HQ
ACT-S128K32C-025P2Q
WS128K32-25HSQ
ACT-S128K32C-025P6Q
AS8S128K32PN-25/883C
AS8S128K32PN-25/883C
WS128K32N-25H1Q
3/
3/
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
WS128K32N-25H1Q
ACT-S128K32N-025P7Q
AS8S128K32P-25/883C
AS8S128K32P-25/883C
WS128K32-25H1Q
WS128K32-25H1Q
ACT-S128K32C-025P7Q
See footnotes at end of table.
3 of 8
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9318709HMA
5962-9318709HNA
5962-9318709HTA
5962-9318709HTA
5962-9318709HUA
5962-9318709HUA
5962-9318709HXA
5962-9318709HXA
5962-9318709HYA
5962-9318709HYA
5962-9318709H4A
5962-9318709H4C
5962-9318709H4A
5962-9318709H4C
5962-9318709H4A
5962-9318709H5A
5962-9318709H5C
5962-9318709H5A
5962-9318709H5C
5962-9318709H5A
5962-9318710HMA
5962-9318710HNA
5962-9318710HTA
5962-9318710HTA
5962-9318710HUA
5962-9318710HUA
5962-9318710HXA
5962-9318710HXA
5962-9318710HYA
5962-9318710HYA
5962-9318710H4A
5962-9318710H4C
5962-9318710H4A
5962-9318710H4C
5962-9318710H4A
5962-9318710H5A
5962-9318710H5C
5962-9318710H5A
5962-9318710H5C
5962-9318710H5A
5962-9318711H4A
5962-9318711H4C
5962-9318711H5A
5962-9318711H5C
3/
3/
3/
3/
3/
3/
3/
3/
3/
ACT-S128K32N-020P3Q
ACT-S128K32C-020P3Q
WS128K32N-20HQ
ACT-S128K32N-020P2Q
WS128K32N-20HSQ
ACT-S128K32N-020P6Q
WS128K32-20HQ
ACT-S128K32C-020P2Q
WS128K32-20HSQ
3/
ACT-S128K32C-020P6Q
AS8S128K32PN-20/883C
AS8S128K32PN-20/883C
WS128K32N-20H1Q
WS128K32N-20H1Q
ACT-S128K32N-020P7Q
AS8S128K32P-20/883C
AS8S128K32P-20/883C
WS128K32-20H1Q
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
3/
WS128K32-20H1Q
ACT-S128K32C-020P7Q
ACT-S128K32N-017P3Q
ACT-S128K32C-017P3Q
WS128K32N-17HQ
ACT-S128K32N-017P2Q
WS128K32N-17HSQ
ACT-S128K32N-017P6Q
WS128K32-17HQ
ACT-S128K32C-017P2Q
WS128K32-17HSQ
3/
3/
ACT-S128K32C-017P6Q
AS8S128K32PN-17/883C
AS8S128K32PN-17/883C
WS128K32N-17H1Q
WS128K32N-17H1Q
ACT-S128K32N-017P7Q
AS8S128K32P-17/883C
AS8S128K32P-17/883C
WS128K32-17H1Q
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
WS128K32-17H1Q
ACT-S128K32C-017P7Q
WS128K32N-15H1Q
WS128K32N-15H1Q
WS128K32-15H1Q
54230
54230
54230
54230
WS128K32-15H1Q
See footnotes at end of table.
4 of 8
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9318712HMA
5962-9318712HMC
5962-9318712HNA
5962-9318712HNC
5962-9318712HTA
5962-9318712HTC
5962-9318712HUA
5962-9318712HUC
5962-9318712HXA
5962-9318712HXC
5962-9318712HYA
5962-9318712HYC
5962-9318712H4A
5962-9318712H4C
5962-9318712H4A
5962-9318712H4C
5962-9318712H4A
5962-9318712H4C
5962-9318712H5A
5962-9318712H5C
5962-9318712H5A
5962-9318712H5C
5962-9318712H5A
5962-9318712H5C
5962-9318713HMA
5962-9318713HMC
5962-9318713HNA
5962-9318713HNC
5962-9318713HTA
5962-9318713HTC
5962-9318713HUA
5962-9318713HUC
5962-9318713HXA
5962-9318713HXC
5962-9318713HYA
5962-9318713HYC
5962-9318713H4A
5962-9318713H4C
5962-9318713H4A
5962-9318713H4C
5962-9318713H4A
5962-9318713H4C
5962-9318713H5A
5962-9318713H5C
5962-9318713H5A
5962-9318713H5C
5962-9318713H5A
5962-9318713H5C
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
ACT-S128K32N-055P3Q-R
ACT-S128K32N-055P3Q-R
ACT-S128K32C-055P3Q-R
ACT-S128K32C-055P3Q-R
ACT-S128K32N-055P2Q-R
ACT-S128K32N-055P2Q-R
ACT-S128K32N-055P6Q-R
ACT-S128K32N-055P6Q-R
ACT-S128K32C-055P2Q-R
ACT-S128K32C-055P2Q-R
ACT-S128K32C-055P6Q-R
ACT-S128K32C-055P6Q-R
AS8S128K32PN-55/883C
AS8S128K32PN-55/883C
WS128K32NH-55H1Q
WS128K32NH-55H1Q
ACT-S128K32N-055P7Q-R
ACT-S128K32N-055P7Q-R
AS8S128K32P-55/883C
AS8S128K32P-55/883C
WS128K32H-55H1Q
WS128K32H-55H1Q
ACT-S128K32C-055P7Q-R
ACT-S128K32C-055P7Q-R
ACT-S128K32N-045P3Q-R
ACT-S128K32N-045P3Q-R
ACT-S128K32C-045P3Q-R
ACT-S128K32C-045P3Q-R
ACT-S128K32N-045P2Q-R
ACT-S128K32N-045P2Q-R
ACT-S128K32N-045P6Q-R
ACT-S128K32N-045P6Q-R
ACT-S128K32C-045P2Q-R
ACT-S128K32C-045P2Q-R
ACT-S128K32C-045P6Q-R
ACT-S128K32C-045P6Q-R
AS8S128K32PN-45/883C
AS8S128K32PN-45/883C
WS128K32NH-45H1Q
WS128K32NH-45H1Q
ACT-S128K32N-045P7Q-R
ACT-S128K32N-045P7Q-R
AS8S128K32P-45/883C
AS8S128K32P-45/883C
WS128K32H-45H1Q
WS128K32H-45H1Q
ACT-S128K32C-045P7Q-R
ACT-S128K32C-045P7Q-R
See footnotes at end of table.
5 of 8
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9318714HMA
5962-9318714HMC
5962-9318714HNA
5962-9318714HNC
5962-9318714HTA
5962-9318714HTC
5962-9318714HUA
5962-9318714HUC
5962-9318714HXA
5962-9318714HXC
5962-9318714HYA
5962-9318714HYC
5962-9318714H4A
5962-9318714H4C
5962-9318714H4A
5962-9318714H4C
5962-9318714H4A
5962-9318714H4C
5962-9318714H5A
5962-9318714H5C
5962-9318714H5A
5962-9318714H5C
5962-9318714H5A
5962-9318714H5C
5962-9318715HMA
5962-9318715HMC
5962-9318715HNA
5962-9318715HNC
5962-9318715HTA
5962-9318715HTC
5962-9318715HUA
5962-9318715HUC
5962-9318715HXA
5962-9318715HXC
5962-9318715HYA
5962-9318715HYC
5962-9318715H4A
5962-9318715H4C
5962-9318715H4A
5962-9318715H4C
5962-9318715H4A
5962-9318715H4C
5962-9318715H5A
5962-9318715H5C
5962-9318715H5A
5962-9318715H5C
5962-9318715H5A
5962-9318715H5C
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
ACT-S128K32N-035P3Q-R
ACT-S128K32N-035P3Q-R
ACT-S128K32C-035P3Q-R
ACT-S128K32C-035P3Q-R
ACT-S128K32N-035P2Q-R
ACT-S128K32N-035P2Q-R
ACT-S128K32N-035P6Q-R
ACT-S128K32N-035P6Q-R
ACT-S128K32C-035P2Q-R
ACT-S128K32C-035P2Q-R
ACT-S128K32C-035P6Q-R
ACT-S128K32C-035P6Q-R
AS8S128K32PN-35/883C
AS8S128K32PN-35/883C
WS128K32NH-35H1Q
WS128K32NH-35H1Q
ACT-S128K32N-035P7Q-R
ACT-S128K32N-035P7Q-R
AS8S128K32P-35/883C
AS8S128K32P-35/883C
WS128K32H-35H1Q
WS128K32H-35H1Q
ACT-S128K32C-035P7Q-R
ACT-S128K32C-035P7Q-R
ACT-S128K32N-025P3Q-R
ACT-S128K32N-025P3Q-R
ACT-S128K32C-025P3Q-R
ACT-S128K32C-025P3Q-R
ACT-S128K32N-025P2Q-R
ACT-S128K32N-025P2Q-R
ACT-S128K32N-025P6Q-R
ACT-S128K32N-025P6Q-R
ACT-S128K32C-025P2Q-R
ACT-S128K32C-025P2Q-R
ACT-S128K32C-025P6Q-R
ACT-S128K32C-025P6Q-R
AS8S128K32PN-25/883C
AS8S128K32PN-25/883C
WS128K32NH-25H1Q
WS128K32NH-25H1Q
ACT-S128K32N-025P7Q-R
ACT-S128K32N-025P7Q-R
AS8S128K32P-25/883C
AS8S128K32P-25/883C
WS128K32H-25H1Q
WS128K32H-25H1Q
ACT-S128K32C-025P7Q-R
ACT-S128K32C-025P7Q-R
See footnotes at end of table.
6 of 8
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9318716HMA
5962-9318716HMC
5962-9318716HNA
5962-9318716HNC
5962-9318716HTA
5962-9318716HTC
5962-9318716HUA
5962-9318716HUC
5962-9318716HXA
5962-9318716HXC
5962-9318716HYA
5962-9318716HYC
5962-9318716H4A
5962-9318716H4C
5962-9318716H4A
5962-9318716H4C
5962-9318716H4A
5962-9318716H4C
5962-9318716H5A
5962-9318716H5C
5962-9318716H5A
5962-9318716H5C
5962-9318716H5A
5962-9318716H5C
5962-9318717HMA
5962-9318717HMC
5962-9318717HNA
5962-9318717HNC
5962-9318717HTA
5962-9318717HTC
5962-9318717HUA
5962-9318717HUC
5962-9318717HXA
5962-9318717HXC
5962-9318717HYA
5962-9318717HYC
5962-9318717H4A
5962-9318717H4C
5962-9318717H4A
5962-9318717H4C
5962-9318717H4A
5962-9318717H4C
5962-9318717H5A
5962-9318717H5C
5962-9318717H5A
5962-9318717H5C
5962-9318717H5A
5962-9318717H5C
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
ACT-S128K32N-020P3Q-R
ACT-S128K32N-020P3Q-R
ACT-S128K32C-020P3Q-R
ACT-S128K32C-020P3Q-R
ACT-S128K32N-020P2Q-R
ACT-S128K32N-020P2Q-R
ACT-S128K32N-020P6Q-R
ACT-S128K32N-020P6Q-R
ACT-S128K32C-020P2Q-R
ACT-S128K32C-020P2Q-R
ACT-S128K32C-020P6Q-R
ACT-S128K32C-020P6Q-R
AS8S128K32PN-20/883C
AS8S128K32PN-20/883C
WS128K32NH-20H1Q
WS128K32NH-20H1Q
ACT-S128K32N-020P7Q-R
ACT-S128K32N-020P7Q-R
AS8S128K32P-20/883C
AS8S128K32P-20/883C
WS128K32H-20H1Q
WS128K32H-20H1Q
ACT-S128K32C-020P7Q-R
ACT-S128K32C-020P7Q-R
ACT-S128K32N-017P3Q-R
ACT-S128K32N-017P3Q-R
ACT-S128K32C-017P3Q-R
ACT-S128K32C-017P3Q-R
ACT-S128K32N-017P2Q-R
ACT-S128K32N-017P2Q-R
ACT-S128K32N-017P6Q-R
ACT-S128K32N-017P6Q-R
ACT-S128K32C-017P2Q-R
ACT-S128K32C-017P2Q-R
ACT-S128K32C-017P6Q-R
ACT-S128K32C-017P6Q-R
AS8S128K32PN-17/883C
AS8S128K32PN-17/883C
WS128K32NH-17H1Q
WS128K32NH-17H1Q
ACT-S128K32N-017P7Q-R
ACT-S128K32N-017P7Q-R
AS8S128K32P-17/883C
AS8S128K32P-17/883C
WS128K32H-17H1Q
WS128K32H-17H1Q
ACT-S128K32C-017P7Q-R
ACT-S128K32C-017P7Q-R
See footnotes at end of table.
7 of 8
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9318718H4A
5962-9318718H4C
5962-9318718H5A
5962-9318718H5C
54230
54230
54230
54230
WS128K32NH-15H1Q
WS128K32NH-15H1Q
WS128K32H-15H1Q
WS128K32H-15H1Q
1/ The lead finish shown for each PIN representing a hermetic
package is the most readily available from the manufacturer
listed for that part. If the desired lead finish is not listed contact
the Vendor to determine its availability.
2/ Caution. Do not use this number for item acquisition. Items
acquired to this number may not satisfy the performance
requirements of this drawing.
3/ Not available from an approved source of supply.
Vendor CAGE
number
Vendor name
and address
0EU86
54230
88379
Austin Semiconductor, Incorporated
8701 Cross Park Drive
Austin, TX 78754-4566
White Electronic Designs Corporation
3601 East University Drive
Phoenix, AZ 85034
Aeroflex Plainview, Incorporated
35 South Service Road
Plainview, NY 11803-4101
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
8 of 8
相关型号：
©2020 ICPDF网 联系我们和版权申明