WR10X4702JTL [WALSIN]
Thick film Technology General purpose chip resistors;型号: | WR10X4702JTL |
厂家: | Walsin Technology |
描述: | Thick film Technology General purpose chip resistors |
文件: | 总8页 (文件大小:239K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Approval sheet
WR10X(W)
±1%, ±5%
Thick film Technology
General purpose chip resistors
Size 1210
Page 1 of 8
ASC_WR10X(W)_V13
Oct.- 2011
Approval sheet
FEATURE
1. High reliability and stability
2. Reduced size of final equipment
3. Lower assembly costs
4. Higher component and equipment reliability
5. RoHS compliant and Lead free products
APPLICATION
•
•
•
Consumer electrical equipment
Automotive application
EDP, Computer application
•
Telecom application
DESCRIPTION
The resistors are constructed in a high grade ceramic body (aluminum oxide). Internal metal electrodes are
added at each end and connected by a resistive paste that is applied to the top surface of the substrate. The
composition of the paste is adjusted to give the approximate resistance required and the value is trimmed to
nominated value within tolerance which controlled by laser trimming of this resistive layer.
The resistive layer is covered with a protective coat. Finally, the two external end terminations are added. For
ease of soldering the outer layer of these end terminations is Tin (lead free) alloy.
Fig 1. Construction of Chip-R
Page 2 of 8
ASC_WR10X(W)_V13
Oct.- 2011
Approval sheet
QUICK REFERENCE DATA
Item
General Specification
WR10X(W)
Series No.
Size code
1210 ( 3225 )
Resistance Tolerance
Resistance Range
±1% ( E96/E24 ), ±5% ( E24 )
Jumper, 1Ω ~ 10MΩ ( E96+E24 series)
> 10R , ≤ ± 100 ppm/°C
1R ~ 10R, ≤ ± 200 ppm/°C
1/3 W ( 0.33 W )
TCR (ppm/°C)
-55°C ~ +155°C
Max. dissipation at Tamb=70°C
Max. Operation Voltage (DC or RMS)
Max. Overload Voltage (DC or RMS)
Climatic category
200V
400V
55/155/56
Type
WR10X
1/3 W
Power Rating At 70C
Resistance
Max. 50mR
2.5 A
Rated Current
Peak Current
6 A
Operating Temperature
-55C ~ 155C
Note :
1.
This is the maximum voltage that may be continuously supplied to the resistor element, see “IEC publication
60115-8”
2.
Max. Operation Voltage : So called RCWV (Rated Continuous Working Voltage) is determined by
RCWV = RatedPower ×Resistance Value or Max. RCWV listed above, whichever is lower.
DIMENSIONS(unit : mm)
Part No
WR10X
3.10 ± 0.10
2.60 ± 0.10
0.50 ± 0.20
0.50 ± 0.20 *1
0.55 ± 0.10
L
W
Tt
Tb
T
*1 original 0.45+/-0.20
Page 3 of 8
ASC_WR10X(W)_V13
Oct.- 2011
Approval sheet
MARKING
3-digits marking(±5%)
Each resistor is marked with a three digits code on the protective coating to designate the nominal resistance
value.
4-digits marking(±1%
)
Each resistor is marked with a four digits code on the protective coating to designate the nominal resistance value.
Example
RESISTANCE
4-digits marking
3-digits marking
90Ω
90R0
-
100Ω
1000
101
6800Ω
6801
682
47000Ω
4702
473
FUNCTIONAL DESCRIPTION
Product characterization
Standard values of nominal resistance are taken from the E96 & E24 series for resistors with a tolerance of
±1%, ±5%. The values of the E24/E96 series are in accordance with “IEC publication 60063”.
Derating
The power that the resistor can dissipate depends on the operating temperature; see Fig.2
Figure 2 Maximum dissipation in percentage of rated power
as a function of the ambient temperature
MOUNTING
Due to their rectangular shapes and small tolerances, Surface Mountable Resistors are suitable for handling by
automatic placement systems.
Chip placement can be on ceramic substrates and printed-circuit boards (PCBs).
Electrical connection to the circuit is by individual soldering condition.
The end terminations guarantee a reliable contact.
Page 4 of 8
ASC_WR10X(W)_V13
Oct.- 2011
Approval sheet
SOLDERING CONDITION
The robust construction of chip resistors allows them
to be completely immersed in a solder bath of 260°C
for 10 seconds. Therefore, it is possible to mount
Surface Mount Resistors on one side of a PCB and
other discrete components on the reverse (mixed
PCBs).
Surface Mount Resistors are tested for solderability
at 235°C during 2 seconds. The test condition for no
leaching is 260°C for 30 seconds. Typical examples
of soldering processes that provide reliable joints
without any damage are given in Fig 3.
Fig 3. Infrared soldering profile for Chip Resistors
CATALOGUE NUMBERS
The resistors have a catalogue number starting with .
WR10
X
4702
F
T
L
Size code
Type code
Resistance code
Tolerance
J: ± 5%
Packaging code
T: 7” Reeled taping
Termination code
WR10: 1210 X :
5%, E24: 2 significant digits
L = Sn base (lead
followed by no. of zeros
free)
5%: 1R ~ 10M
1%: 10R ~ 1M
W:
F: ± 1%
100Ω = 101_
10KΩ = 103
P: Jumper
1% E24+E96:
3 significant
1%: < 10R; > 1M0
digits followed by no. of
zeros
102Ω
=1020
=3742
=2200
37.4KΩ
220Ω
ꢀ
Reeled tape packaging : 8mm width paper taping 5000pcs per 7” reel.
Page 5 of 8
ASC_WR10X(W)_V13
Oct.- 2011
Approval sheet
TEST AND REQUIREMENTS(JIS C 5201-1 : 1998)
The tests are carried out in accordance with IEC publication 68, "Recommended basic climatic and mechanical
robustness testing procedure for electronic components" and under standard atmospheric conditions according
to IEC 68-1, subclause 5.3, unless otherwise specified.
Temperature: 15ºC to 35ºC.
Relative humidity: 45% to 75%.
Air pressure: 86kPa to 106 kPa (860 mbar to 1060 mbar).
REQUIREMENT
TEST
PROCEDURE / TEST METHOD
Resistor
0Ω
DC resistance values measured at the test voltages specified below :
<10Ω@0.1V, <100Ω@0.3V, <1KΩ@1.0V,
DC resistance
Within the specified
tolerance
<50mΩ
Clause 4.5
<10KΩ@3V, <100KΩ@10V, <1MΩ@25V, <10MΩ@30V
Natural resistance change per change in degree centigrade.
Refer to
Temperature
Coefficient of
Resistance(T.C.R)
“QUICK REFERENCE
DATA”
R2 − R
×106 (ppm/°C) t1 : 20°C+5°C-1°C
1
N/a
R
(
t2 − t1
)
1
Clause 4.8
R1 : Resistance at reference temperature
R2 : Resistance at test temperature
Short time overload
(S.T.O.L)
Permanent resistance change after a 5second application of a
voltage 2.5 times RCWV or the maximum overload voltage specified
in the above list, whichever is less.
∆R/R max. ±(2%+0.10Ω)
<50mΩ
<50mΩ
Clause 4.13
Resistance to soldering
heat(R.S.H)
Un-mounted chips completely immersed for 10±1second in a SAC
solder bath at 260℃±5ºC
ΔR/R max. ±(1%+0.05Ω)
no visible damage
Clause 4.18
Solderability
Clause 4.17
95% coverage min., good tinning and
no visible damage
Un-mounted chips completely immersed for 2±0.5 second in a SAC
solder bath at 235℃±5℃
30 minutes at -55°C±3°C, 2~3 minutes at 20°C+5°C-1°C, 30
minutes at +155°C±3°C, 2~3 minutes at 20°C+5°C-1°C, total 5
continuous cycles
Temperature cycling
∆R/R max. ±(1%+0.05Ω)
< 50mΩ
< 50mΩ
Clause 4.19
1000 +48/-0 hours, loaded with RCWV or Vmax in humidity chamber
controller at 40°C±2°C and 90~95% relative humidity, 1.5hours on
and 0.5 hours off
10Ω≤R<1MΩ :
Damp Heat
∆R/R max. ±(3%+0.10Ω)
R<10Ω, R≥1MΩ :
(Load life in humidity)
Clause 4.24
∆R/R max. ±(5%+0.10Ω)
1000+48/-0 hours; loaded with RCWV or Vmax in chamber controller
Load Life (Endurance)
Ditto.
70±2ºC, 1.5 hours on and 0.5 hours off
Clause 4.25
Resistors mounted on a 90mm glass epoxy resin PCB(FR4), No visual damaged,
Bending strength
< 50mΩ
bending once 3mm for 10sec.
∆R/R max. ±(1%+0.05Ω)
Clause 4.33
No remarkable damage or removal of
the terminations
Adhesion
Pressurizing force: 5N, Test time: 10±1sec.
Clause 4.32
Page 6 of 8
ASC_WR10X(W)_V13
Oct.- 2011
Approval sheet
REQUIREMENT
Resistor
TEST
PROCEDURE / TEST METHOD
0Ω
Insulation Resistance
Apply the maximum overload voltage (DC) for 1minutes
R≧10GΩ
Clause 4.6
Dielectric Withstand
Voltage
Apply the maximum overload voltage (AC) for 1 minutes
No breakdown or flashover
Clause 4.7
Page 7 of 8
ASC_WR10X(W)_V13
Oct.- 2011
Approval sheet
PACKAGING
Paper Tape specifications (unit :mm)
Component Size / Series
W
F
E
P0
ΦD
Φ1.50
T
+0.1
−0.0
8.00±0.30
3.50±0.20
1.75±0.10
4.00±0.10
WR10X
Component Size / Series
WR10X
A
B
P1
4.00±0.10
3.60±0.20
3.00±0.20
Max. 1.0
Reel dimensions
Symbol
A
B
C
D
(unit : mm)
13.0±0.2
9.0±0.5
Φ178.0±2.0
Φ60.0±1.0
Taping quantity
-
Chip resistors 5,000 pcs/reel
Page 8 of 8
ASC_WR10X(W)_V13
Oct.- 2011
相关型号:
©2020 ICPDF网 联系我们和版权申明