OP43B102K631CT [WALSIN]
High voltage in a given case size;型号: | OP43B102K631CT |
厂家: | Walsin Technology |
描述: | High voltage in a given case size |
文件: | 总10页 (文件大小:3030K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Multilayer Ceramic Capacitors
Approval Sheet
MULTILAYER CERAMIC CAPACITORS
Open-Mode Series (50V to 630V)
0805 to 1812 Sizes
X7R Dielectric
Halogen Free & RoHS Compliance
*Contents in this sheet are subject to change without prior notice.
Page 1 of 10
ASC_ Open Mode_(OP)_012Q_AS
Dec. 2018
Multilayer Ceramic Capacitors
Approval Sheet
1. INTRODUCTION
WTC open-mode series MLCC is designed by a special internal electrode pattern, which can reduce voltage
concentrations by distributing voltage gradients throughout the entire capacitor. This special design also affords
open-mode pattern to prevent circuit leakage when focused to failure in a board flex situation.
2. FEATURES
3. APPLICATIONS
a. High voltage in a given case size.
b. Circuit open during product cracking.
c. High stability and reliability.
a. High current applications.
b. Power supply and related industries
c. The other mechanical stress concerned products.
4. HOW TO ORDER
OP
31
B
102
K
201
C
T
Series
Size
Dielectric Capacitance Tolerance Rated voltage
Termination
Packaging
OP=Open-mode
21=0805 (2012)
31=1206 (3216)
32=1210 (3225)
43=1812 (4532)
B=X7R
Two significant K=±10%
digits followed M=±20%
by no. of zeros.
And R is in
Two significant
digits followed by
no. of zeros. And
R is in place of
decimal point.
C=Cu/Ni/Sn
T=7” reeled
G=13” reeled
place of
decimal point.
500=50 VDC
101=100 VDC
201=200 VDC
251=250 VDC
501=500 VDC
631=630 VDC
eg.:
102=10x102
=1000pF
Page 2 of 10
ASC_ Open Mode_(OP)_012Q_AS
Dec. 2018
Multilayer Ceramic Capacitors
Approval Sheet
5. EXTERNAL DIMENSIONS
Size
Inch (mm)
L (mm)
W (mm)
T (mm)/Symbol
Remark
MB (mm)
L
0.80±0.10
1.25±0.10
0.80±0.10
0.95±0.10
1.25±0.10
1.60±0.20
0.95±0.10
1.25±0.10
1.60±0.20
2.50±0.30
1.25±0.10
2.00±0.20
B
D
B
0805 (2012)
2.00±0.15
1.25±0.10
0.40±0.20
T
#
3.20±0.15
1.60±0.15
C
D
G
C
D
G
M
D
K
W
1206 (3216)
1210 (3225)
0.50±0.20
#
#
#
#
#
#
#
#
MB
MB
3.20±0.20
3.20±0.30
1.60±0.20
2.50±0.20
Fig. 1 The outline of MLCC
0.50±0.25
0.60±0.25
3.20±0.40
2.50±0.30
3.20±0.30
1812 (4532) 4.50+0.5/-0.3
# Reflow soldering only is recommended.
6. GENERAL ELECTRICAL DATA
Dielectric
X7R
Size
0805, 1206, 1210, 1812
100pF to 1µF
Capacitance*
Capacitance tolerance**
Rated voltage (WVDC)
K (±10%), M (±20%)
50V, 100V, 200V, 250V, 500V, 630V
50V,100V: ≥2.5 x WVDC
200V and 250V: ≥2 x WVDC
500V,630V: ≥1.5 x WVDC
-55 to +125°C
Dielectric strength
Operating temperature
Capacitance characteristic
Termination
±15%
Ni/Sn (lead-free termination)
* Measured at 25°C ambient temperature and 30~70% r elated humidity. Apply 1.0±0.2Vrms, 1.0kHz±10%.
** Preconditioning for Class II MLCC: Perform a heat treatment at 150±10°C for 1 hour, then leave in a mbient condition for 24±2 hours
before measurement.
Page 3 of 10
ASC_ Open Mode_(OP)_012Q_AS
Dec. 2018
Multilayer Ceramic Capacitors
Approval Sheet
7. CAPACITANCE RANGE
DIELECTRIC
X7R
SIZE
0805
1206
1210
1812
RATED VOLTAGE
100pF (101)
120pF (121)
150pF (151)
180pF (181)
220pF (221)
270pF (271)
330pF (331)
390pF (391)
470pF (471)
560pF (561)
680pF (681)
820pF (821)
1,000pF (102)
1,200pF (122)
1,500pF (152)
1,800pF (182)
2,200pF (222)
2,700pF (272)
3,300pF (332)
3,900pF (392)
4,700pF (472)
5,600pF (562)
6,800pF (682)
8,200pF (822)
0.010µF (103)
0.012µF (123)
0.015µF (153)
0.018µF (183)
0.022µF (223)
0.027µF (273)
0.033µF (333)
0.039µF (393)
0.047µF (473)
0.056µF (563)
0.068µF (683)
0.082µF (823)
0.10µF (104)
0.12µF (124)
0.15µF (154)
0.18µF (184)
0.22µF (224)
0.27µF (274)
0.33µF (334)
0.39µF (394)
0.47µF (474)
0.56µF (564)
0.68µF (684)
0.82µF (824)
1.0µF (105)
100 200 250 500 630 50 100 200 250 500 630 100 200 250 500 630 100 200 250 500 630
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
D
D
D
D
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
D
D
D
D
D
D
D
D
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
D
D
D
D
D
D
D
D
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
D
D
D
D
D
D
D
D
D
D
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
D
D
D
G
G
G
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
G
G
G
G
G
G
G
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
G
G
G
G
G
G
G
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
G
G
G
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
G
G
G
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
D
D
G
G
M
M
M
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
D
G
G
G
G
M
M
M
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
D
G
G
G
G
M
M
M
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
G
G
G
G
G
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
G
G
G
G
G
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
K
K
K
K
K
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
K
K
K
K
K
K
K
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
K
K
K
K
K
K
K
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
K
K
K
K
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
K
K
K
K
The letter in cell is expressed the symbol of product thickness.
Page 4 of 10
ASC_ Open Mode_(OP)_012Q_AS
Dec. 2018
Multilayer Ceramic Capacitors
Approval Sheet
8. PACKAGING DIMENSION AND QUANTITY
Paper tape
Plastic tape
Size
Thickness (mm)/Symbol
7” reel
13” reel
7” reel
-
13” reel
0.80±0.10
1.25±0.10
0.80±0.10
0.95±0.10
1.25±0.10
1.60±0.20
0.95±0.10
1.25±0.10
1.60±0.20
2.50±0.30
1.25±0.10
2.00±0.20
B
D
B
4k
-
15k
-
0805
-
3k
-
10k
-
4k
-
15k
C
D
G
C
D
G
M
D
K
-
-
-
-
-
-
-
-
-
3k
3k
2k
3k
3k
2k
1k
1k
1k
10k
10k
10k
10k
10k
-
1206
-
-
-
-
1210
1812
-
-
6k
5k
-
-
-
Unit: pieces
9. INNER CONSTRUCTION OF OPEN-MODE DESIGN
MB
CP
CP
MB
Crack
Crack
Crack
Fig. 4 Floating design (one kind of
open-mode design)– circuit open
during cracking.
Fig. 2 Normal design (CP<MB) –
Fig. 3 Open-mode design (CP>MB) –
circuit open during cracking.
circuit leakage during cracking.
Page 5 of 10
ASC_ Open Mode_(OP)_012Q_AS
Dec. 2018
Multilayer Ceramic Capacitors
Approval Sheet
10. RELIABILITY TEST CONDITIONS AND REQUIREMENTS
No.
Item
Test Condition
Requirements
1. Visual and
Mechanical
---
* No remarkable defect.
* Dimensions to conform to individual specification sheet.
2. Capacitance
3. Q/ D.F.
(Dissipation
Factor)
1.0±0.2Vrms, 1kHz±10%
* Shall not exceed the limits given in the detailed spec.
*Before initial measurement (Class II only): To apply de-aging
at 150°C for 1hr then set for 24±2 hrs at room temp .
* D.F. ≤2.5%
* D.F. ≤3% : 50V / 1206≧0.47µF
4. Dielectric
Strength
* To apply voltage:
* No evidence of damage or flash over during test.
50V, 100V
≥2.5 times VDC
≥2 times VDC
200V~300V
500V~630V
≥1.5 times VDC
* Duration: 1 to 5 sec.
* Charge & discharge current less than 50mA.
5. Insulation
Resistance
50V, 100V, To apply rated voltage for max. 120 sec.
≥10GΩ or RxC≥100Ω-F whichever is smaller.
X7R=100V: RxC≥100Ω-F
≥200V, To apply rated voltage for 60 sec.
6. Temperature
Coefficient
With no electrical load.
Within ±15%.
Operating temperature: -55~125°C at 25°C
*Before initial measurement (Class II only): To apply de-aging
at 150°C for 1hr then set for 24±2 hrs at room temp .
* Pressurizing force:
7. Adhesive
Strength of
Termination
8. Vibration
Resistance
* No remarkable damage or removal of the terminations.
5N (≤0603) and 10N (>0603)
* Test time: 10±1 sec.
* Vibration frequency: 10~55 Hz/min.
* No remarkable damage.
* Total amplitude: 1.5mm
* Cap change and Q/D.F.: To meet initial spec.
* Test time: 6 hrs. (Two hrs each in three mutually
perpendicular directions.)
*Before initial measurement (Class II only): To apply de-aging
at 150°C for 1hr then set for 24±2 hrs at room temp .
*Cap./DF(Q) Measurement to be made after de-aging at 150°C
for 1hr then set for 24±2 hrs at room temp.
9. Solderability
* Solder temperature: 235±5°C
* Dipping time: 2±0.5 sec.
95% min. coverage of all metalized area.
10. Bending Test * The middle part of substrate shall be pressurized by means * No remarkable damage.
of the pressurizing rod at a rate of about 1 mm per second until * Cap change: X7R: within ±12.5%
the deflection becomes 1 mm and then the pressure shall be
(This capacitance change means the change of capacitance under
maintained for 5±1 sec.
specified flexure of substrate from the capacitance measured before
the test.)
*Before initial measurement (Class II only): To apply de-aging
at 150°C for 1hr then set for 24±2 hrs at room temp .
* Measurement to be made after keeping at room temp. for
24±2 hrs.
11. Resistance to * Solder temperature: 260±5°C
Soldering Heat * Dipping time: 10±1 sec
* Preheating: 120 to 150°C for 1 minute before imme rse the
* No remarkable damage.
* Cap change: X7R: within ±7.5%
* Q/D.F., I.R. and dielectric strength: To meet initial requirements.
* 25% max. leaching on each edge.
capacitor in a eutectic solder.
*Before initial measurement (Class II only): To apply de-aging
at 150°C for 1hr then set for 24±2 hrs at room temp .
*Cap. / DF(Q) / I.R. Measurement to be made after de-aging at
150°C for 1hr then set for 24±2 hrs at room temp.
Page 6 of 10
ASC_ Open Mode_(OP)_012Q_AS
Dec. 2018
Multilayer Ceramic Capacitors
Approval Sheet
No.
Item
Test Condition
Requirements
12. Temperature
Cycle
* Conduct the five cycles according to the temperatures and * No remarkable damage.
time.
Step
* Cap change:within ±7.5%
Temp. (°C)
Min. operating temp. +0/-3
Room temp.
Time (min.)
30±3
* Q/D.F., I.R. and dielectric strength: To meet initial requirements.
1
2
3
4
2~3
Max. operating temp. +3/-0
Room temp.
30±3
2~3
*Before initial measurement (Class II only): To apply de-aging
at 150°C for 1hr then set for 24±2 hrs at room temp .
* Cap. / DF(Q) / I.R. Measurement to be made after de-aging
at 150°C for 1hr then set for 24±2 hrs at room temp .
* Test temp.: 40±2°C
13. Humidity
(Damp Heat)
Steady State
* No remarkable damage.
* Cap change: within ±12.5%
* Q/D.F. value:
* Humidity: 90~95% RH
* Test time: 500+24/-0hrs.
*Before initial measurement (Class II only): To apply de-aging D.F. ≤3.0%
at 150°C for 1hr then set for 24±2 hrs at room temp . D.F. ≤6% : 50V / 1206
* Cap. / DF(Q) / I.R. Measurement to be made after de-aging * I.R.: ≥1GΩ or RxC≥50Ω-F whichever is smaller.
≧
0.47µF
at 150°C for 1hr then set for 24±2 hrs at room temp .
* Test temp.: 40±2°C
X7R=100V: RxC≥10Ω-F
* No remarkable damage.
* Cap change: within ±12.5%
* Q/D.F. value:
14. Humidity
(Damp Heat)
Load
* Humidity: 90~95%RH
* Test time: 500+24/-0 hrs.
* To apply voltage:rated voltage (Max. 500V)
D.F. ≤3.0%
*Before initial measurement (Class II only): To apply de-aging D.F. ≤6% : 50V / 1206
≧0.47µF
at 150°C for 1hr then set for 24±2 hrs at room temp .
* Cap. / DF(Q) / I.R. Measurement to be made after de-aging
at 150°C for 1hr then set for 24±2 hrs at room temp .
* Test temp.: X7R: 125±3°C
* I.R.: ≥500MΩ or RxC≥25Ω-F whichever is smaller.
X7R=100V: RxC≥5Ω-F
15. High
Temperature
Load
* No remarkable damage.
* Cap change: within ±12.5%
* Q/D.F. value:
* To apply voltage:
(1) V<500V: 200% of rated voltage.
(Endurance)
(2) 500V~630V: 150% of rated voltage.
* Test time: 1000+24/-0 hrs.
D.F. ≤3.0%
D.F. ≤6% : 50V / 1206
≧0.47µF
*Before initial measurement (Class II only): To apply de-aging * I.R.: ≥1GΩ or RxC≥50Ω-F whichever is smaller.
at 150°C for 1hr then set for 24±2 hrs at room temp .
* Cap. / DF(Q) / I.R. Measurement to be made after de-aging
at 150°C for 1hr then set for 24±2 hrs at room temp .
X7R=100V: RxC≥10Ω-F
Page 7 of 10
ASC_ Open Mode_(OP)_012Q_AS
Dec. 2018
Multilayer Ceramic Capacitors
APPENDIXES
Approval Sheet
◙ Tape & reel dimensions
Fig. 5 The dimension of paper tape
Fig. 6 The dimension of plastic tape
Size
0805
1206
C, D
1210
1812
Thickness
B
C, D, I
B
G
C, D
G
D, K, M
1.50
1.90
< 1.80
< 2.00
< 3.70
<2.30
< 3.05
< 3.05
< 3.20
<4.00
A0
B0
T
+/-0.20
+/-0.50
2.30
+/-0.20
3.50
+/-0.50
< 2.70
< 4.00
< 3.80
< 3.80
0.23
+/-0.1
0.23
+/-0.1
0.23
+/-0.1
0.23
+/-0.1
0.23
+/-0.1
0.23
+/-0.1
≦1.20
≦1.20
-
< 2.50
-
< 2.50
< 2.50
< 1.50
< 2.50
< 3.20
K0
W
8.00
+/-0.30
8.00
+/-0.30
8.00
+/-0.30
8.00
+/-0.30
8.00
+/-0.30
8.00
+/-0.30
8.00
+/-0.30
8.00
+/-0.30
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
P0
40.00
40.00
40.00
40.00
40.00
40.00
40.00
40.00
10xP0
P1
+/-0.20
+/-0.20
+/-0.20
+/-0.20
+/-0.20
+/-0.20
+/-0.20
+/-0.20
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
4.00
+/-0.10
2.00
+/-0.05
2.00
+/-0.05
2.00
+/-0.05
2.00
+/-0.05
2.00
+/-0.05
2.00
+/-0.05
2.00
+/-0.05
2.00
+/-0.05
P2
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
D0
D1
E
+0.1/-0
+0.1/-0
+0.1/-0
+0.1/-0
+0.1/-0
+0.1/-0
+0.1/-0
+0.1/-0
1.00
+/-0.10
1.00
+/-0.10
1.00
+/-0.10
1.00
+/-0.10
1.00
+/-0.10
1.00
+/-0.10
-
-
1.75
+/-0.10
1.75
+/-0.10
1.75
+/-0.10
1.75
+/-0.10
1.75
+/-0.10
1.75
+/-0.10
1.75
+/-0.10
1.75
+/-0.10
3.50
+/-0.05
3.50
+/-0.05
3.50
+/-0.05
3.50
+/-0.05
3.50
+/-0.05
3.50
+/-0.05
3.50
+/-0.05
3.50
+/-0.05
F
Size
0603, 0805, 1206, 1210
10”
1808, 1812
7”
Reel size
7”
13”
C
W1
A
13.0+0.5/-0.2
8.4+1.5/-0
178.0±1.0
60.0+1.0/-0
13.0+0.5/-0.2
8.4+1.5/-0
13.0+0.5/-0.2
8.4+1.5/-0
330.0±1.0
100±1.0
13.0+0.5/-0.2
12.4+2.0/-0
178.0±1.0
60.0+1.0/-0
250.0±1.0
N
100.0±1.0
Fig. 7 The dimension of reel
Page 8 of 10
ASC_ Open Mode_(OP)_012Q_AS
Dec. 2018
Multilayer Ceramic Capacitors
Approval Sheet
◙ Example of customer label
a. Customer name
b. WTC order series and item number
c. Customer P/O
d. Customer P/N
e. Description of product
f. Quantity
g. Bar code including quantity & WTC P/N or customer
h. WTC P/N
i. Shipping date
j. Order bar code including series and item numbers
k. Serial number of label
*Customized label is available upon request
◙ Constructions
No.
1
2
3
4
5
Name
X7R
Ceramic material
Inner electrode
BaTiO3 based
Ni
Cu
Inner layer
Termination
Middle layer
Outer layer
Ni
Fig. 8 The construction of MLCC
Sn (Matt)
◙ Storage and handling conditions
(1) To store products at 5 to 40°C ambient temperature and 20 to 70%. related humidity conditions.
(2) The product is recommended to be used within one year after shipment. Check solderability in case of shelf life
extension is needed.
Cautions:
a. The corrosive gas reacts on the terminal electrodes of capacitors, and results in the poor solderability.
Do not store the capacitors in the ambience of corrosive gas (e.g., hydrogen sulfide, sulfur dioxide,
chlorine, ammonia gas etc.)
b. In corrosive atmosphere, solderability might be degraded, and silver migration might occur to cause low
reliability.
c. Due to the dewing by rapid humidity change, or the photochemical change of the terminal electrode by
direct sunlight,the solderability and electrical performance may deteriorate. Do not store capacitors under
direct sunlight or dewing condition. To store products on the shelf and avoid exposure to moisture.
.
Page 9 of 10
ASC_ Open Mode_(OP)_012Q_AS
Dec. 2018
Multilayer Ceramic Capacitors
Approval Sheet
◙ Recommended soldering conditions
The lead-free termination MLCCs are not only to be used on SMT against lead-free solder paste, but also suitable
against lead-containing solder paste. If the optimized solder joint is requested, increasing soldering time, temperature and
concentration of N2 within oven are recommended.
4/ sec max
Over 60sec at least by
natural cooling
Fig. 9 Recommended reflow soldering profile for SMT process
with SnAgCu series solder paste.
Fig. 10 Recommended wave soldering profile for SMT process
with SnAgCu series solder.
Page 10 of 10
ASC_ Open Mode_(OP)_012Q_AS
Dec. 2018
相关型号:
©2020 ICPDF网 联系我们和版权申明