310113562 [VPC]
i2 MICRO iCON PCB ASSEMBLY;
| 型号： | 310113562 |
| 厂家： | 
VIRGINIA PANEL CORPORATION |
| 描述： | i2 MICRO iCON PCB ASSEMBLY PC |
| 文件： | 总3页 (文件大小：1350K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
i2 MICRO iCON USER’S MANUAL: SECTION 8
VIRGINIA PANEL CORPORATION
i2 MICRO iCON PCB ASSEMBLY
84 PIN HEADER, PART # 510 109 204 • 60 PIN HEADER, PART # 510 109 206
MOUNTING BRACKET, PART # 310 113 562
TOOLS REQUIRED
Phillips Head Screwdriver
ASSEMBLY INSTRUCTIONS
1. Assemble two headers to the PCB. See next page for
recommended PCB layout.
NOTE: To ensure a secure connection without damaging the
PCB, the board must be properly supported between the
mounting holes to distribute pressure evenly. Otherwise, the
insertion force may be high enough to damage or break the
board. Reference VPC part # 910 121 199 if a tool is needed.
2. Using the Phillips head screwdriver, secure the headers and
mounting bracket (Part # 310 113 562) to the PCB using the
supplied 2 mm screws (Figure A).
3. Secure the receiver to the mounting panel (Figure B) following
the recommended panel cutout (see Section 3).
4. Using the Phillips head screwdriver, press the PCB and headers
onto the receiver and secure the mounting bracket to the
receiver using the supplied captive 2-56 screw (Figure C).
Figure A. Secure headers and mounting bracket to PCB.
Figure B. Secure receiver to mounting panel.
Figure C. Secure mounting bracket to receiver.
9/24/14
8-1
For more information visit vpc.com
i2 MICRO iCON USER’S MANUAL: SECTION 8
VIRGINIA PANEL CORPORATION
i2 MICRO iCON PCB LAYOUT
HEADER, 84 POSITION RIGHT ANGLE WITH COMPLIANT PIN • PART # 510 109 204
1.09
0.97
46.86
1.84ꢀ
.043
.038
PLATED THRU HOLE
TYP. 84 PLCS.
(HASL) TIN/LEAD PLATED
44.07
1.73ꢀ
.006
A B C
42.39
1.669
+
-
.002
.072
TYP.
.001
UNPLATED THRU HOLE
MOUNTING BOSS
2 PLCS.
33.02
1.300
PIN A1
13 EQ. SPCS@.100[2.ꢀ4]
B
ꢀ.ꢀ1
.217
3.76
.148
3.12 0.0ꢀ
.123 .002
3.76
.148
C
14.0ꢀ 0.0ꢀ
.ꢀꢀ3 .002
12.70
13.41
.ꢀ28
17.78
.700
.ꢀ00
ꢀ EQ. SPCS. @
.100 [2.ꢀ4]
1
.100 TYP. THRU HOLE
MOUNTING SCREW
UNPLATED
HEADER PERIMETER
R
.0ꢀ0
OUTLINE
TYP.
PIN F1
2 PLCS.
RECOMMENDED PCB LAYOUT
CONNECTOR MOUNTS THIS SIDE
A
BOARD THICKNESS = [1.ꢀ7] .062 OR [2.29] .090
TOLERANCES ARE:
.062 .002 PAD
BOTH SIDES
[.2ꢀ].01
.XX =
[.13].00ꢀ
.XXX =
UNLESS OTHERWISE SPECIFIED
Figure A. PCB layout. Connector mounts this side.
Board thickness = [1.57] .062 or [2.29] .090
49.53
1.950
COMPLIANT PIN
Figure B. Two header layout for 310 130 101 receiver.
Figure C. Compliant header pin.
9/24/14
8-2
For more information visit vpc.com
i2 MICRO iCON USER’S MANUAL: SECTION 8
VIRGINIA PANEL CORPORATION
i2 MICRO iCON STANDARD PCB LAYOUT
i2 RECEIVER • PART # 310 130 101
16.26
.640
12.70
1.78
.070
.500
5 EQ. SPCS.
@ [2.54] .100
PIN A1
1
RECOMMENDED PCB LAYOUT
CONNECTOR MOUNTS THIS SIDE
TOLERANCES ARE:
[.25].01
.XX =
8.76
.345
[.13].005
.XXX =
UNLESS OTHERWISE SPECIFIED
1
.0021 LOCATION TOLERANCES
APPLIES TO PLATED THRU HOLES
33.02
1.300
1
PIN F1
13 EQ. SPCS.
@ [2.54] .100
0.94 0.08
.037 .003
PLATED THRU HOLE
TYP. 168 PLCS.
49.53
1.950
100.08
3.940
.060 PAD
TYP. 168 PLCS.
2.54
.100 THRU
Figure B. i2 receiver, Part # 310 130 101, loaded
with twin female contacts, Part # 610 138 200.
Twin male headers are used to connect the
female contacts to the PCB plated thru holes.
Figure A. PCB layout for i2 receiver, Part # 310 130 101. Thru hole
and pad diameters are for VPC QuadraPaddle male Adapter
Contact, Part # 610 138 117. The size of these holes may be
different if a header from a different manufacturer is used.
Connector mounts this side.
PCB
HEADER, .100" SPACING TWIN MALE
SOLDERED TO PCB CREATES A
SEPERABLE INTERFACE
0.22” [5.6 mm] /
0.45” [11.4 mm]
i2 RECEIVER
HEADER CARRIER HEIGHT
Figure C. Twin male header.
SPACER (SEE NOTE)
NOTE: Figure C details 0.22” [5.59 mm]/0.45” [11.43 mm]
min/max engagement.
NOTE: Minimum spacer height = 0.24” + header carrier
height - panel thickness (if used).
Any additional height beyond this minimum must be
added to the header post limits shown in Figure C.
Figure D. A PCB can be mounted directly to the back of an i2 receiver as
shown above. Four 2-56 or M2 screws are required to mount the receiver.
Spacers may be needed to prevent unwanted stress on the PCB.
9/24/14
8-3
For more information visit vpc.com
相关型号：
©2020 ICPDF网 联系我们和版权申明