M35C206M010BZSS [VISHAY]
Tantalum Capacitor, Polarized, Tantalum (wet), 10V, 20% +Tol, 20% -Tol, 20uF, Surface Mount, 8331, CHIP;
| 型号： | M35C206M010BZSS |
| 厂家： | 
VISHAY |
| 描述： | Tantalum Capacitor, Polarized, Tantalum (wet), 10V, 20% +Tol, 20% -Tol, 20uF, Surface Mount, 8331, CHIP 电容器 |
| 文件： | 总5页 (文件大小：80K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
M35
Vishay
www.vishay.com
Wet Tantalum Capacitors Surface Mount, Molded Case
FEATURES
• Molded surface mountable design
• Terminations: standard tin/lead (SnPb),
100 % tin (RoHS compliant) available
• Industry standard ratings
• Model M35 wet tantalum electrolytic chip
capacitors incorporate the advantages of all the
varieties of electrolytic capacitors and eliminate most of
the disadvantages. These units have a 3 V reverse voltage
capability at + 85 °C and a higher ripple current capability
than any other electrolytic type with similar combinations
of capacitance and case size.
• Compliant to RoHS Directive 2002/95/EC
Note
* Pb containing terminations are not RoHS compliant, exemptions
may apply
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C
Life Test: Capacitors are capable of withstanding a 2000 h
life test at a temperature of + 85 °C or + 125 °C at the
applicable rated DC working voltage.
(to + 125 °C with voltage derating)
Capacitance Tolerance: At 120 Hz, + 25 °C.
standard. 10 %, 5 % available as special.
20 %
Following life test:
DC Leakage Current (DCL Max.): At + 25 °C and above:
Leakage current shall not exceed the values listed in the
Standard Ratings Tables.
1. DCL, measured at + 85 °C rated voltage, shall not be in
excess of the original requirement.
2. The equivalent series resistance shall not exceed 150 %
of the initial requirement.
3. Change in capacitance shall not exceed 10 % from the
initial measurement.
ORDERING INFORMATION
M35
C
826
M
125
B
Z
S
L
MODEL
CASE
CODE
CAPACITANCE CAPACITANCE DC VOLTAGE RATING
TERMINATION
AND PACKAGING
RELIABILITY TEMP
LEVEL
ESR
TOLERANCE
AT + 85 °C
See
Ratings
and Case
Codes
table
This is
expressed in
picofarads.
The first two
digits are the
significant
K = 10 %
M = 20 %
This is expressed in
A = 100 % tin
Z = Non-ER S = Std S = Std.
volts. To complete the (RoHS compliant),
L = Low
three-digit block,
zeros precede the
voltage rating.
A decimal point is
indicated by an “R”
(6R3 = 6.3 V)
bulk
B = Std, tin/lead,
bulk
figures. The
third is the
number of zeros
to follow.
Note
•
Packaging: The use of formed plastic tubes for packing bulk components is standard
DIMENSIONS in inches [millimeters]
W
P
L
CASE CODE
L (MAX.)
W
H
P (MIN.)
TW
TH (MIN.)
0.835
[21.2]
0.315 0.012
[8 0.3]
0.295 0.012
[7.5 0.3]
0.118
[3.0]
0.236 0.012
[6.0 0.3]
0.075
[1.9]
C
Revision: 07-Nov-11
Document Number: 40095
1
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
M35
Vishay
www.vishay.com
RECOMMENDED REFLOW PROFILES
Tp °C
tp
TL °C
T
s MAX. °C
(tL)
Ts MIN. °C
PREHEAT (ts)
25 °C
TIME (s)
ALL CASE CODES
Tp
Tp
TL
TL
Ts MIN.
Ts MIN.
Ts MAX.
Ts MAX.
ts
ts
tp
tL
Lead (Pb)-free Sn/Pb
Lead (Pb)-free Sn/Pb Lead (Pb)-free Sn/Pb Lead (Pb)-free Sn/Pb Lead (Pb)-free Sn/Pb
260 °C
240 °C 10
217 °C
183 °C
150 °C
100 °C
200 °C
150 °C
60 to 150
60 to 90 60
MOUNTING
Due to the size and weight of these capacitors, we recommend that a supplemental mounting restraint to be used in printed
circuit board attachment in addition to the reflowed solder.
One recommendation is to use an adhesive such as defined in the J-STD-001DS.
This is the Space Application Electronic Hardware Addendum to J-STD-001 (Requirements for Solder Electrical and Electronic
Assemblies).
STANDARD RATINGS
MAX. CAPACITANCE
CHANGE (%) AT
MAX.
RIPPLE
40 kHz
RMS
MAX. DCL (μA) AT
CAPACITANCE CASE
MAX. ESR MAX. ESR
AT + 25 °C AT - 55 °C
PART NUMBER
(μF)
CODE
+ 85 °C
+ 25 °C
- 55 °C + 85 °C + 125 °C
+ 125 °C
(mA)
6 VDC AT + 85 °C; 4 VDC AT + 125 °C
30
68
C
C
C
M35C306(1)006(2)ZS(3)
M35C686(1)006(2)ZS(3)
M35C227(1)006(2)ZS(3)
4.0
3.2
3.0
100
60
1.0
1.0
2.0
2.0
2.0
9.0
- 40
- 40
- 64
+ 10.5
+ 14
+ 12
+ 16
+ 16
820
960
220
36
+ 13
1000
8 VDC AT + 85 °C; 5 VDC AT + 125 °C
25
56
C
C
C
M35C256(1)008(2)ZS(3)
M35C566(1)008(2)ZS(3)
M35C187(1)008(2)ZS(3)
4.0
3.3
3.0
100
59
1.0
1.0
2.0
2.0
2.0
9.0
- 40
- 40
- 60
+ 10.5
+ 14
+ 12
+ 16
+ 16
820
900
180
45
+ 13
1000
10 VDC AT + 85 °C; 7 VDC AT + 125 °C
20
47
C
C
C
C
M35C206(1)010(2)ZS(3)
M35C476(1)010(2)ZS(3)
M35C127(1)010(2)ZS(3)
M35C157(1)010(2)ZS(3)
4.0
3.7
3.2
3.0
120
90
1.0
1.0
2.0
2.0
2.0
2.0
6.0
9.0
- 32
- 36
- 40
- 55
+ 10.5
+ 14
+ 12
+ 16
+ 16
+ 16
820
855
900
900
120
150
54
+ 14
54
+ 13
Note
Part number definitions:
•
(1) Capacitance tolerance: K, M
(2) Termination/packaging: (see Ordering Information)
Reliability level: Z = Non-ER
Temperature: S = STD
(3) ESR: S = STD, L = Low (1/2 standard ESR value)
Revision: 07-Nov-11
Document Number: 40095
2
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
M35
Vishay
www.vishay.com
STANDARD RATINGS
MAX. CAPACITANCE
CHANGE (%) AT
MAX.
RIPPLE
40 kHz
RMS
MAX. DCL (μA) AT
CAPACITANCE CASE
MAX. ESR MAX. ESR
AT + 25 °C AT - 55 °C
PART NUMBER
(μF)
CODE
+ 85 °C
+ 25 °C
- 55 °C + 85 °C + 125 °C
+ 125 °C
(mA)
15 VDC AT + 85 °C; 10 VDC AT + 125 °C
15
33
C
C
C
C
M35C156(1)015(2)ZS(3)
M35C336(1)015(2)ZS(3)
M35C826(1)015(2)ZS(3)
M35C107(1)015(2)ZS(3)
4.4
4.0
3.9
3.9
155
90
1.0
1.0
2.0
2.0
2.0
2.0
6.0
9.0
- 24
- 28
- 35
- 44
+ 10.5
+ 14
+ 12
+ 16
+ 16
+ 16
780
820
900
900
82
72
+ 12
100
72
+ 13
25 VDC AT + 85 °C; 15 VDC AT + 125 °C
10
22
56
68
C
C
C
C
M35C106(1)025(2)ZS(3)
M35C226(1)025(2)ZS(3)
M35C566(1)025(2)ZS(5)
M35C686(1)025(2)ZS(5)
5.3
4.2
4.3
4.3
220
140
90
1.0
1.0
2.0
2.0
2.0
2.0
6.0
9.0
- 16
- 20
- 25
- 40
+ 8
+ 10.5
+ 12
+ 9
715
800
850
850
+ 12
+ 15
+ 15
90
+ 12
30 VDC AT + 85 °C; 20 VDC AT + 125 °C
8
C
C
C
C
M35C805(1)030(2)ZS(3)
M35C156(1)030(2)ZS(3)
M35C476(1)030(2)ZS(3)
M35C566(1)030(2)ZS(3)
6.6
6.2
5.2
5.2
275
175
100
100
1.0
1.0
2.0
2.0
2.0
2.0
6.0
9.0
- 16
- 20
- 23
- 38
+ 8
+ 10.5
+ 12
+ 12
+ 12
+ 15
+ 15
640
780
800
800
15
47
56
+ 12
35 VDC AT + 85 °C; 22 VDC AT + 125 °C
15
39
C
C
M35C156(1)035(2)ZS(3)
M35C396(1)035(2)ZS(3)
6.2
4.1
175
61
0.75
2.0
1.5
6.0
- 20
- 22
+ 10.5
+ 12
+ 12
+ 14
660
820
50 VDC AT + 85 °C; 30 VDC AT + 125 °C
5
C
C
C
M35C505(1)050(2)ZS(3)
M35C106(1)050(2)ZS(3)
M35C336(1)050(2)ZS(3)
8.0
6.4
5.0
400
250
135
1.0
1.0
2.0
2.0
2.0
9.0
- 16
- 24
- 29
+ 5
+ 8
+ 6
+ 9
580
715
700
10
33
+ 10
+ 12
60 VDC AT + 85 °C; 40 VDC AT + 125 °C
4
C
C
C
M35C405(1)060(2)ZS(3)
M35C825(1)060(2)ZS(3)
M35C276(1)060(2)ZS(3)
9.3
6.6
5.0
550
275
144
1.0
1.0
3.0
2.0
2.0
12
- 16
- 24
- 24
+ 5
+ 8
+ 6
+ 9
525
625
700
8.2
27
+ 10
+ 12
75 VDC AT + 85 °C; 50 VDC AT + 125 °C
3.5
6.8
22
C
C
C
M35C355(1)075(2)ZS(3)
M35C685(1)075(2)ZS(3)
M35C226(1)075(2)ZS(3)
9.5
6.8
5.1
650
300
157
1.0
1.0
3.0
2.0
2.0
12
- 16
- 20
- 19
+ 5
+ 8
+ 6
+ 9
525
610
600
+ 10
+ 12
100 VDC AT + 85 °C; 65 VDC AT + 125 °C
2.5
4.7
10
C
C
C
M35C255(1)100(2)ZS(3)
M35C475(1)100(2)ZS(3)
M35C106(1)100(2)ZS(3)
10.6
8.5
950
500
200
1.0
1.0
3.0
2.0
2.0
12
- 16
- 16
- 17
+ 7
+ 7
+ 8
+ 8
505
565
800
5.9
+ 10
+ 12
125 VDC AT + 85 °C; 85 VDC AT + 125 °C
1.7
3.6
6.8
C
C
C
M35C175(1)125(2)ZS(3)
M35C365(1)125(2)ZS(3)
M35C685(1)125(2)ZS(3)
15.6
10.0
11.7
1250
600
1.0
1.0
3.0
2.0
2.0
12
- 16
- 16
- 14
+ 7
+ 7
+ 8
+ 8
415
520
700
300
+ 10
+ 12
Note
Part number definitions:
•
(1) Capacitance tolerance: K, M
(2) Termination/packaging: (see Ordering Information)
Reliability level: Z = Non-ER
Temperature: S = STD
(3) ESR: S = STD, L = Low (1/2 standard ESR value)
Revision: 07-Nov-11
Document Number: 40095
3
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
M35
Vishay
www.vishay.com
PERFORMANCE CHARACTERISTICS OF M35 CAPACITORS
ELECTRICAL CHARACTERISTICS
ITEM
PERFORMANCE CHARACTERISTICS
Operating temperature range
Capacitor tolerance
Capacitance change (maximum)
ESR
- 55 °C to + 125 °C
20 %, 10 % at 120 Hz
AC ripple current
Limits per Standard Ratings table. Measured per requirements of MIL-PRF-39006.
DCL (maximum leakage current)
Impedance (maximum)
Reverse voltage shall be in accordance with MIL-PRF-39006/22.
Units are capable of withstanding 3 V in reverse at + 85 °C for 125 h.
Surge voltage shall be in accordance with MIL-PRF-39006.
Reverse voltage
The DC rated surge voltage is the maximum voltage to which the capacitors should be subjected
under any conditions. This includes transients and peak ripple at the highest line voltage. The
surge voltage is 115 % of rated DC working voltage.
Surge voltage
Life test
The capacitors shall be capable of withstanding a 2000 h life test at 85 °C at rated voltage.
ENVIRONMENTAL CHARACTERISTICS
ITEM
CONDITION
COMMENTS
Hermeticity
Moisture resistance
MIL-PRF-39006
MIL-PRF-39006
The internal component has been tested to be compliant to the
hermeticity requirements of MIL-PRF-39006/22.
The internal component has been tested to be compliant to the
moisture resistance requirements of MIL-PRF-39006/22.
The internal component has been tested to be compliant to the
altitude or reduced barometric pressure requirements of
MIL-PRF-39006/22 (150 000 feet).
Altitude/barometric pressure
(reduced)
MIL-PRF-39006
MECHANICAL CHARACTERISTICS
ITEM
CONDITION
COMMENTS
Thermal shock
Shock
Vibration (high frequency)
Vibration (random)
MIL-STD-202, Method 107, A
MIL-STD-202, Method 213
MIL-STD-202, Method 204
MIL-STD-202, Method 214
Per MIL-PRF-39006, 30 cycles
Per MIL-PRF-39006, 500 g
Per MIL-PRF-39006, 80 g
Per MIL-PRF-39006, 53.79 g
The capacitor must withstand solder dipping of the terminals at
260 °C for 10 s. The capacitor must not be visibly damaged and the
electrical characteristics must not be affected.
The terminations must be solderable per the requirements of
MIL-PRF-55365 para. 4.10
Resistance to solder heat
Solderability
MIL-STD-202, Method 210
ANSI J-STD-002
The part marking shall include Vishay name, trademark,
capacitance, voltage, date code and lot symbol.
Part markings
MIL-STD-1285
3.5
Weight (typical) in g
PAD DIMENSIONS in millimeters
A
B
C
C
CASE CODE
A (MIN.)
B (NOM.)
C (NOM.)
D (NOM.)
C
22.7
14.7
4.0
6.4
STANDARD PACKAGING QUANTITY
SERIES
CASE CODE
BULK/TUBE
M35
C
10 pcs
Revision: 07-Nov-11
Document Number: 40095
4
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
Document Number: 91000
1
相关型号：
M35C206M010CZSL
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 10V, 20% +Tol, 20% -Tol, 20uF, Surface Mount, CHIP, ROHS COMPLIANT
VISHAY
M35C206M010CZSS
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 10V, 20% +Tol, 20% -Tol, 20uF, Surface Mount, CHIP, ROHS COMPLIANT
VISHAY
M35C206M010DZSL
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 10V, 20% +Tol, 20% -Tol, 20uF, Surface Mount, CHIP
VISHAY
M35C206M010DZSS
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 10V, 20% +Tol, 20% -Tol, 20uF, Surface Mount, CHIP
VISHAY
M35C206M010EZSL
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 10V, 20% +Tol, 20% -Tol, 20uF, Surface Mount, CHIP, ROHS COMPLIANT
VISHAY
M35C206M010FZSL
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 10V, 20% +Tol, 20% -Tol, 20uF, Surface Mount, CHIP
VISHAY
M35C206M010FZSS
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 10V, 20% +Tol, 20% -Tol, 20uF, Surface Mount, CHIP
VISHAY
M35C226K025FZSL
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 25V, 10% +Tol, 10% -Tol, 22uF, Surface Mount, CHIP
VISHAY
M35C227K006FZSL
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 6V, 10% +Tol, 10% -Tol, 220uF, Surface Mount, CHIP
VISHAY
M35C227K006FZSS
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 6V, 10% +Tol, 10% -Tol, 220uF, Surface Mount, CHIP
VISHAY
M35C227M006FZSL
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 6V, 20% +Tol, 20% -Tol, 220uF, Surface Mount, CHIP
VISHAY
M35C256K008FZSL
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 8V, 10% +Tol, 10% -Tol, 25uF, Surface Mount, CHIP
VISHAY
©2020 ICPDF网 联系我们和版权申明