CRA06P083MZTA [VISHAY]
Thick Film Chip Resistor Array;
| 型号： | CRA06P083MZTA |
| 厂家： | 
VISHAY |
| 描述： | Thick Film Chip Resistor Array |
| 文件： | 总4页 (文件大小：96K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CRA06P
www.vishay.com
Vishay
Thick Film Chip Resistor Array
FEATURES
• Concave terminal array with square corners
• 4 and 8 terminal package with isolated resistors
• Wide ohmic range: 10R to 1M0
• AEC-Q200 qualified
CRA06P thick film resistor array is constructed on a high
grade ceramic body with concave terminations. A small
package enables the design of high density circuits. The
single component reduces board space, component counts
and assembly costs.
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
POWER RATING LIMITING ELEMENT
TEMPERATURE
COEFFICIENT
ppm/K
RESISTANCE
RANGE
TOLERANCE
%
MODEL
CIRCUIT
P70 °C
VOLTAGE MAX.
E-SERIES
W
V
100
200
1
24 + 96
24
0.063
50
10 to 1M
CRA06P
03
2; 5
Zero-Ohm-Resistor: Rmax. = 50 m, Imax. = 1 A
TECHNICAL SPECIFICATIONS
CRA06P
03 CIRCUIT
PARAMETER
UNIT
Rated dissipation at 70 °C (2)
Limiting element voltage (1)
Insulation voltage (1 min)
Category temperature range
Insulation resistance
W per element
0.063
V
50
VDC/AC peak
100
°C
-55 to +155
> 109
Notes
(1)
(2)
Rated voltage: P x R
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRA06P08347K0JTA (1)
C
R
A
0
6
P
0
8
3
4
7
K
0
J
T
A
TERMINAL
STYLE
MODEL
PIN
CIRCUIT
VALUE
TOLERANCE
PACKAGING (2)
SPECIAL
CRA06
P
04
08
3 = 03
R = decimal
K = thousand
M = million
F = 1 ꢀ
G = 2 ꢀ
J = 5 ꢀ
TA
TC
Up to 2 digits
0000 = 0 jumper Z = 0 jumper
Product Description: CRA06P 08 03 473
J
RT1 e3
CRA06P
08
03
473
J
RT1
e3
MODEL
TERMINAL COUNT CIRCUIT TYPE
RESISTANCE VALUE
TOLERANCE
PACKAGING (4) LEAD (Pb)-FREE
CRA06P
04
08
03
473 = 47 k
4702 = 47 k
10R0 = 10
100 = 10
F = 1 ꢀ
G = 2 ꢀ
RT1
RT6
e3 = pure tin
termination finish
J = 5 ꢀ
Z = 0 jumper
000 = 0 jumper
First two digits (3 for 1 ꢀ)
are significant. Last digit
is the multiplier.
Notes
(1)
Preferred way for ordering products is by use of the PART NUMBER
Please refer to the table PACKAGING, see next page
(2)
Revison: 23-Feb-17
Document Number: 31047
1
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRA06P
www.vishay.com
Vishay
PACKAGING
PACKAGING CODE
PAPER TAPE
MODEL
TAPE WIDTH
DIAMETER
PITCH
PIECES/REEL
PART NUMBER
PRODUCT DESCRIPTION
180 mm/7"
4 mm
4 mm
5000
TA
RT1
CRA06P
8 mm
330 mm/13"
20 000
TC
RT6
CIRCUIT
DERATING
120
100
80
03 CIRCUIT
60
40
20
0
8 pin
4 pin
- 55
- 25
0
25
50
75
70
100
125
155 175
Ambient Temperature in °C
DIMENSIONS
DIMENSIONS in millimeters
PIN
NO#
L
A
B
C
P
T
W
A
C
4
1.60
3.20
0.20
0.30
0.30
0.20
0.40
0.40
0.80
0.60
1.60
w
8
0.40
0.15
0.40
0.20
0.80
-
0.60
0.10
1.60
0.15
Tol.
P
B
T
L
SOLDER PAD DIMENSIONS in millimeters
c
w
p
a
b
WAVE
0.8
2.6
0.8
0.4
0.9
c
b
w
p
a
Revison: 23-Feb-17
Document Number: 31047
2
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRA06P
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
REQUIREMENTS
PERMISSIBLE CHANGE (R/R) (1)
TEST
(clause)
CONDITIONS OF TEST
STABILITY
STABILITY
CLASS 2 OR BETTER
CLASS 1 OR BETTER
Stability for product types:
-
10 to 1 M
10 to 1 M
CRA06P
Resistance (4.5)
1 ꢀ
2 ꢀ; 5 ꢀ
200 ppm/K
(20 / -55 / 20) °C and
(20 / 125 / 20) °C
Temperature coefficient (4.8.4.2)
100 ppm/K
U = 2.5 x (P70 x R)1/2
2 x Umax.; 0.5 s
Overload (4.13)
(0.25 ꢀ R + 0.05 )
(0.5 ꢀ R + 0.05 )
Aging 4 h at 155 °C, dryheat
Solder bath method; 235 °C; 2 s
Visual examination
Good tinning ( 95 ꢀ covered)
no visible damage
Solderability (4.17.5) (2)
Solder bath method;
(260 5) °C; (10 1) s
Resistance to soldering heat (4.18.2)
Rapid change of temperature (4.19)
Damp heat, steady state (4.24)
(0.25 ꢀ R + 0.05 )
(0.5 ꢀ R + 0.05 )
(0.5 ꢀ R + 0.05 )
(2 ꢀ R + 0.1 )
30 min at LCT = -55 °C;
30 min at UCT = 125 °C; 5 cycles
(0.25 ꢀ R + 0.05 )
(1 ꢀ R + 0.05 )
(40 2) °C; 56 days;
(93 3) ꢀ RH
16 h at UCT = 125 °C; 1 cycle at 55 °C;
2 h at LCT = -55 °C;
1 h/1 kPa at 15 °C to 35 °C;
5 cycles at 55 °C
Climatic sequence (4.23)
(1 ꢀ R + 0.05 )
(2 ꢀ R + 0.1 )
U = (P70 x R)1/2
U = Umax.; whichever is less severe
U = (P70 x R)1/2
U = Umax.; whichever is less severe
1.5 h “ON”; 0.5 h “OFF”;
70 °C; 1000 h
Endurance at 70 °C (4.25.1)
(1 ꢀ R + 0.05 )
(2 ꢀ R + 0.1 )
Extended endurance (4.25.1.8)
Duration extended to 8000 h
(2 ꢀ R + 0.1 )
(1 ꢀ R + 0.05 )
(4 ꢀ R + 0.1 )
(2 ꢀ R + 0.1 )
Endurance at upper category
temperature (4.25.3)
UCT = 125 °C; 1000 h
Notes
(1) Figures are given for a single element
(2) Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years
APPLICABLE SPECIFICATIONS
• EN 60115-1
• EN 140400
• EN 140401-802
• IEC 60068-2-X
• EIA 481
Generic specification
Sectional specification
Detail specification
Variety of environmental test procedures
Packaging of SMD components
Revison: 23-Feb-17
Document Number: 31047
3
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
Document Number: 91000
1
相关型号：
©2020 ICPDF网 联系我们和版权申明