BFC233667682 [VISHAY]
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 0.0068 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT;
| 型号： | BFC233667682 |
| 厂家： | 
VISHAY |
| 描述： | CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 0.0068 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT 电容器 |
| 文件： | 总12页 (文件大小：151K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
Interference Suppression Film Capacitors
MKP Radial Potted Type
FEATURES
• 10 mm to 15 mm lead pitch
• Supplied loose in box, taped on reel
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
APPLICATIONS
Y2 class
For Y2 electromagnetic interference suppression between
line and ground applications (50 Hz/60 Hz) with a maximum
mains voltage of 300 VAC
.
For application limitations refer to section “Application
Notes”.
QUICK REFERENCE DATA
Capacitance range (E12 series)
Capacitance tolerance
0.001 μF to 0.047 μF (preferred values acc. to E6)
20 %; 10 %
55/105/56/C for product volumes 1750 mm3
Climatic testing class according to EN60068-1
55/105/56/B for product volumes > 1750 mm3
Rated AC voltage
300 VAC; 50 Hz to 60 Hz
1000 VDC
Permissible DC voltage
Maximum application temperature
105 °C
IEC 60384-14 ed-4 (2013) edition and EN132400
IEC 60065 requires, pass. flamm. class B for volumes > 1750 mm3
UL 60384-14; ENEC
Reference standards
Dielectric
Polypropylene film
Metallized film
Electrodes
Series construction (for > 10 mm pitch)
Construction
Triple construction (for > 7.5 mm and 10 mm pitch)
Encapsulation
Leads
Plastic case, epoxy resin sealed, flame retardant UL-class 94 V-0
Tinned wire
C-value; tolerance; rated voltage; sub-class; manufacturer’s type designation;
code for dielectric material; manufacturer location; year and week
Marking
Note
•
For more detailed data and test requirements, contact: rfi@vishay.com
DIMENSIONS in millimeters
l
w
h
lt
Ø dt
P
ꢀ0.
Revision: 21-Sep-16
Document Number: 28115
1
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
COMPOSITION OF CATALOG NUMBER
TYPE AND PITCHES
MULTIPLIER
(nF)
336 6
Y2
1ꢀ0ꢀ mm
150ꢀ mm
CAPACITANCE
(numerically)
ꢀ01
1
2
3
Example:
1ꢀ3 = 1ꢀ x 1 = 1ꢀ nF
BFC2 336 6X XX X
2222(*) 336 6X XX X
(*) Old ordering code
TYPE
PACKAGING
LEAD CONFIGURATION
C-TOL.
2ꢀ %
PREFERRED TYPES
Lead length 305 mm + 1 mm/- ꢀ05 mm (pitch = 1ꢀ mm) or
305 mm ꢀ03 mm (pitch = 15 mm)
336 6
Y2
BFC2 336 6ꢀ000
Loose in box
PACKAGING
Loose in box
Lead length 250ꢀ mm 20ꢀ mm
BFC2 336 66000
TYPE
LEAD CONFIGURATION
C-TOL.
1ꢀ %
ON REQUEST
Lead length 305 mm + 1 mm/- ꢀ05 mm (pitch = 1ꢀ mm) or
305 mm ꢀ03 mm (pitch = 15 mm)
BFC2 336 61000
336 6
Y2
Lead length 250ꢀ mm 20ꢀ mm
BFC2 336 67000
BFC2 336 63000
BFC2 336 6.000
2ꢀ %
1ꢀ %
H = 1805 mm; Pꢀ = 1207 mm;
reel diameter 5ꢀꢀ mm
Taped on reel (1)
Note
(1)
For detailed tape specification refer to packaging information: www.vishay.com/doc?28139
SPECIFIC REFERENCE DATA
DESCRIPTION
VALUE
Rated AC voltage (URAC
)
300 V
Permissible DC voltage (URDC
)
1000 V
at 10 kHz
10 x 10-4
Tangent of loss angle
Rated voltage pulse slope (dU/dt)R at 420 VDC
200 V/μs
R between leads, for C 0.33 μF at 100 V; 1 min
R between leads and case; 100 V; 1 min
Withstanding (DC) voltage (cut off current 10 mA) (1); rise time 1000 V/s
> 15 000 M
> 30 000 M
3400 V; 1 min
2100 V; 1 min
Withstanding (AC) voltage between leads and case
Note
(1)
See “Voltage Proof Test for Metalized Film Capacitors”: www.vishay.com/doc?28169
Revision: 21-Sep-16
Document Number: 28115
2
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
ELECTRICAL DATA AND ORDERING CODE
DIMENSIONS
CATALOG NUMBER BFC2 336 6..... AND PACKAGING
REEL
LOOSE IN BOX
(500 mm) (1)(2)
URAC CAP.
MASS
(g) (3)
w x h x l
(mm)
lt = 3.5 mm + 1 mm/- 0.5 mm (10 mm)
OR 3.5 mm 0.3 mm (= 15 mm)
H = 18.5 mm;
P0 = 12.7 mm
(V)
(μF)
lt = 25.0 mm 2.0 mm
LAST 5 DIGITS OF
LAST 5 DIGITS OF
SPQ
LAST 5 DIGITS OF
CATALOG NUMBER
SPQ
SPQ
CATALOG NUMBER
CATALOG NUMBER
PITCH = 10.0 mm 0.ꢀ mm; dt = 0.6 mm 0.06 mm; C-TOL. = 20 ꢁ
0.0010
0.0015
0.0022
0.0033
0.0047
0.0068
60102
60152
60222
60332
60472
60682
66102
66152
66222
66332
66472
66682
63102
63152
63222
63332
63472
63682
4.0 x 10.0 x 12.5
5.0 x 11.0 x 12.5
0.6
1250
1400
1100
1000
0.82
1000
PITCH = 15.0 mm 0.ꢀ mm; dt = 0.6 mm 0.06 mm; C-TOL. = 20 ꢁ
0.0068
0.010
0.015
69005
60103
60153
69009
66103
66153
69006
63103
63153
5.0 x 11.0 x 17.5
6.0 x 12.0 x 17.5
1.0
1100
900
1000
1000
1.4
PITCH = 15.0 mm 0.ꢀ mm; dt = 0.8 mm 0.08 mm; C-TOL. = 20 ꢁ
0.022
0.033
7.0 x 13.5 x 17.5
8.5 x 15.0 x 17.5
1.8
2.4
3.0
60223
60333
60473
66223
66333
66473
63223
63333
63473
800
650
600
750
500
0.047 10.0 x 16.5 x 17.5
500
450
PITCH = 10.0 mm 0.ꢀ mm; dt = 0.6 mm 0.06 mm; C-TOL. = 10 ꢁ
0.0010
0.0012
0.0015
61102
61122
61152
61182
61222
61272
61332
61392
61472
61562
67102
67122
67152
67182
67222
67272
67332
67392
67472
67562
64102
64122
64152
64182
64222
64272
64332
64392
64472
64562
0.0018
300
4.0 x 10.0 x 12.5
0.0022
0.6
1.1
1000
1250
1400
1100
0.0027
0.0033
0.0039
0.0047
5.0 x 11.0 x 12.5
0.0056
1000
1000
PITCH = 15.0 mm 0.ꢀ mm; dt = 0.80 mm 0.08 mm; C-TOL. = 10 ꢁ
0.0056
69001
61682
61822
61103
61123
61153
61183
69007
67682
67822
67103
67123
67153
67183
69003
64682
64822
64103
64123
61153
64183
0.0068
0.0082 5.0 x 11.0 x 17.5
1.0
1100
900
0.010
0.012
1000
1000
0.015
6.0 x 12.0 x 17.5
0.018
1.4
PITCH = 15.0 mm 0.ꢀ mm; dt = 0.80 mm 0.08 mm; C-TOL. = 10 ꢁ
0.022
0.027
0.033
0.039
0.047
7.0 x 13.5 x 17.5
8.5 x 15.0 x 17.5
1.8
61223
61273
61333
61393
61473
67223
67273
67333
67393
67473
64223
64273
64333
61393
64473
800
650
750
500
500
450
2.4
10.0 x 16.5 x 17.5
3.0
600
Notes
•
SPQ = Standard packing quantity
(1)
H = In-tape height; P0 = Sprocket hole distance; for detailed specifications refer to packaging information: www.vishay.com/doc?28139
Reel diameter = 365 mm is available on request
Weight for short lead product only
(2)
(3)
Revision: 21-Sep-16
Document Number: 28115
3
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
APPROVALS
SAFETY APPROVALS Y2
VOLTAGE
VALUE
FILE NUMBERS
LINKS
EN 60384-14 (ENEC)
(= IEC 60384-14 ed-4 (2013))
300 VAC
1 nF to 47 nF
FI 2016038
www.vishay.com/doc?28204
UL 60384-14
300 VAC
300 VAC
300 VAC
1 nF to 47 nF
1 nF to 47 nF
1 nF to 47 nF
E354331
E354331
FI 9219
www.vishay.com/doc?28189
www.vishay.com/doc?28203
CSA-E384-14
CB-test-certificate
The ENEC-approval together with the CB-certificate replace all national marks of the following countries (they have already signed the
ENEC-agreement): Austria; Belgium; Czech. Republic; Denmark; Finland; France; Germany; Greece; Hungary; Ireland; Italy; Luxembourg;
Netherlands; Norway; Portugal; Slovenian; Spain; Switzerland and United Kingdom.
MOUNTING
Normal Use
The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for
mounting in printed-circuit boards by means of automatic insertion machines.
For detailed tape specifications refer to packaging information: www.vishay.com/doc?28139
Specific Method of Mounting to Withstand Vibration and Shock
In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the
printed-circuit board:
• The capacitors shall be mechanically fixed by the leads
Space Requirements on Printed Circuit Board
The maximum space for length (Imax.), width (wmax.) and height (hmax.) of film capacitors to take in account on the printed circuit
board is shown in the drawings.
• For products with pitch 15 mm, w = l = 0.3 mm; h = 0.1 mm
Eccentricity defined as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product
concerned.
wmax0 = W + Δ
Eccentricity
CBA116
Imax0 = I + Δ
hmax0 = h + Δ
Seating plane
SOLDERING CONDITIONS
For general soldering conditions and wave soldering profile, we refer to the application note:
“Soldering Guidelines for Film Capacitors”: www.vishay.com/doc?28171
Storage Temperature
Tstg = -25 °C to +35 °C with RH maximum 75 % without condensation
Ratings and Characteristics Reference Conditions
Unless otherwise specified, all electrical values apply to an ambient temperature of 23 °C 1 °C, an atmospheric pressure of
86 kPa to 106 kPa and a relative humidity of 50 % 2 %.
For reference testing, a conditioning period shall be applied over 96 h 4 h by heating the products in a circulating air oven at
the rated temperature and a relative humidity not exceeding 20 %.
Revision: 21-Sep-16
Document Number: 28115
ꢀ
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
CHARACTERISTICS
1ꢀ3
.
2
typical
1ꢀ2
1ꢀ1
1ꢀꢀ
ꢀ
- 2
- .
- 6
.7 nF
≤
1ꢀ nF <
min0
1ꢀ1
1ꢀ2
1ꢀ3
1ꢀ.
1ꢀ5
- 5ꢀ
ꢀ
5ꢀ
Tamb (°C) 1ꢀꢀ
f (Hz)
Capacitance as a function of ambient temperature
(typical curve)
Tangent of loss angle as a function of frequency
(typical curve)
1ꢀ3
1ꢀ2
1 nF
.07 nF
1ꢀ nF
.7 nF
1ꢀ1
1ꢀꢀ
Y2
1ꢀ1
1ꢀ-1
1ꢀ-2
1ꢀꢀ
C (nF)
1ꢀ.
1ꢀ6
1ꢀ7
1ꢀ8
f (Hz)
1
1ꢀ5
1ꢀ
.7
Impedance as a function of frequency
(typical curve)
Resonant frequency as a function of capacitance
(typical curve)
1ꢀ3
1ꢀ3
.7 nF
1ꢀ2
1ꢀ1
1ꢀꢀ
1ꢀ-1
1ꢀ nF
.07 nF
1nF
Tamb ≤ 1ꢀ5 °C
Tamb ≤ 1ꢀ5 °C
1ꢀ1
1ꢀ1
1ꢀ3
Max. RMS voltage as a function of frequency
1ꢀ.
1ꢀ5
1ꢀ2
1ꢀ1
1ꢀ2
1ꢀ3
1ꢀ.
1ꢀ5
f (Hz)
f (Hz)
Max. RMS current as a function of frequency
Revision: 21-Sep-16
Document Number: 28115
5
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
1ꢀ6
1ꢀ5
1ꢀ.
8ꢀ
ꢀ
2ꢀ
.ꢀ
6ꢀ
1ꢀꢀ
Tamb (°C)
Insulation resistance as a function of ambient temperature
(typical curve)
APPLICATION NOTES
• For Y2 electromagnetic interference suppression between line and ground (50 Hz/60 Hz) with a maximum mains voltage of
300 VAC 10 % instability.
• For capacitors connected in parallel, normally the proof voltage and possibly the rated voltage must be reduced. For
information depending of the capacitance value and the number of parallel connections contact: rfi@vishay.com.
• These capacitors are not intended for continuous pulse applications. For these situations, capacitors of the AC and pulse
program must be used.
• The maximum ambient temperature must not exceed 105 °C.
• Rated voltage pulse slope:
If the pulse voltage is lower than the rated voltage, the values of the specific reference data can be multiplied by 420 VDC and
divided by the applied voltage.
Revision: 21-Sep-16
Document Number: 28115
6
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
INSPECTION REQUIREMENTS
General Notes
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication
IEC 60384-14 ed-4 (2013) and Specific Reference Data.”
GROUP C INSPECTION REQUIREMENTS
D
OR
ND
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
D
4.1 Dimensions (detail)
As specified in chapters “General data” of
this specification
Initial measurements
Capacitance
Tangent of loss angle at 10 kHz
4.3 Robustness of terminations
4.4 Resistance to soldering heat
Tensile: Load 10 N; 10 s
No visible damage
Bending: Load 5 N; 4 x 90°
No pre-drying
Method: 1A
Solder bath: 260 °C
Duration: 10 s
4.19 Component solvent resistance
4.4.2 Final measurements
Isopropylalcohol at room temperature
Method: 2
Immersion time: 5 min 0.5 min
Recovery time:
Min. 1 h, max. 2 h
Visual examination
Capacitance
No visible damage
Legible marking
|C/C| 5 % of the value measured
initially
Tangent of loss angle
Insulation resistance
Increase of tan : 0.008
Compared to values measured initially
As specified in section “Insulation
Resistance” of this specification
SUB-GROUP C1B PART OF SAMPLE
OF SUB-GROUP C1
D
Initial measurements
Capacitance
Tangent of loss angle at 10 kHz
4.20 Solvent resistance of the marking
Isopropylalcohol at room temperature
Method: 1
No visible damage
Legible marking
Rubbing material: Cotton wool
Immersion time: 5 min 0.5 min
4.6 Rapid change of temperature
4.6.1 Inspection
A = - 55 °C
B = + 105 °C
5 cycles
Duration t = 30 min
Revision: 21-Sep-16
Document Number: 28115
7
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
GROUP C INSPECTION REQUIREMENTS
D
OR
ND
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1B PART OF SAMPLE
OF SUB-GROUP C1
D
4.7
Vibration
Visual examination
No visible damage
Mounting: See section “Mounting” of this
specification
Procedure B4
Frequency range: 10 Hz to 55 Hz.
Amplitude: 0.75 mm or
Acceleration 98 m/sꢀ
(whichever is less severe)
Total duration 6 h
4.7.2 Final inspection
4.9 Shock
Visual examination
No visible damage
Mounting: See section “Mounting” for
more information
Pulse shape: Half sine
Acceleration: 490 m/sꢀ
Duration of pulse: 11 ms
4.9.2 Final measurements
Visual examination
Capacitance
No visible damage
|C/C| 5 % of the value measured
initially
Tangent of loss angle
Insulation resistance
Increase of tan :
0.008
Compared to values measured initially
As specified in section “Insulation
Resistance” of this specification
SUB-GROUP C1 COMBINED SAMPLE
OF SPECIMENS OF SUB-GROUPS
C1A AND C1B
D
4.11 Climatic sequence
4.11.1 Initial measurements
Capacitance
Measured in 4.4.2 and 4.9.2
Tangent of loss angle:
Measured initially in C1A and C1B
4.11.2 Dry heat
Temperature: 105 °C
Duration: 16 h
4.11.3 Damp heat cyclic
Test Db
First cycle
4.11.4 Cold
Temperature: - 55 °C
Duration: 2 h
4.11.5 Damp heat cyclic
Test Db
remaining cycles
Revision: 21-Sep-16
Document Number: 28115
8
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
GROUP C INSPECTION REQUIREMENTS
D
OR
ND
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1 COMBINED SAMPLE
OF SPECIMENS OF SUB-GROUPS
C1A AND C1B
D
4.11.6 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|C/C| 5 % of the value measured in
4.11.1.
Tangent of loss angle
Increase of tan :
0.008
Compared to values measured in 4.11.1.
Voltage proof
No permanent breakdown or flash-over
2250 VDC; 1 min between term.
Insulation resistance
50 % of values specified in section
“Insulation resistance” of this
specification
SUB-GROUP C2
D
4.12 Damp heat steady state
56 days, 40 °C, 90 % to 95 % RH no load
capacitance
4.12.1 Initial measurements
4.12.3 Final measurements
Capacitance
Tangent of loss angle at 10 kHz
Visual examination
Capacitance
No visible damage
Legible marking
|C/C| 5 % of the value measured in
4.12.1.
Tangent of loss angle
Increase of tan :
0.007
Compared to values measured in 4.12.1.
Voltage proof
No permanent breakdown or flash-over
2250 VDC; 1 min between term.
Insulation resistance
50 % of values specified in section
“Insulation resistance” of this
specification
SUB-GROUP C3
D
4.13.1 Initial measurements
Capacitance
Tangent of loss angle at 10 kHz
4.13 Impulse voltage
4.14 Endurance
3 successive impulses, full wave, peak
voltage:
5 kV
Max. 24 pulses
No selfhealing breakdowns or flashover
Duration: 1000 h
1.7 URAC at 105 °C
Once in every hour the voltage is
increased to 1000 VRMS for 0.1 s via
resistor of 47 5 %
Revision: 21-Sep-16
Document Number: 28115
9
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
GROUP C INSPECTION REQUIREMENTS
D
OR
ND
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C3
D
4.14.7 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|C/C| 10 % compared to values
measured in 4.13.1.
Tangent of loss angle
Increase of tan :
0.007
Compared to values measured in 4.13.1.
Voltage proof
No permanent breakdown or flash-over
2250 VDC;
1 min between terminations
Insulation resistance
50 % of values specified in section
“Insulation resistance” of this
specification
SUB-GROUP Cꢀ
D
4.15 Charge and discharge
10 000 cycles
(50 c/s) charge to UR half sinewave
Duration: 5 ms
Discharge resistance:
420 VDC
R = ---------------------------------------------------
1.5 x CdU/dt
R
min. = 2.2
4.15.1 Initial measurements
4.15.3 Final measurements
Capacitance
Tangent of loss angle at 10 kHz
Capacitance
|C/C| 10 % compared to values
measured in 4.15.1.
Tangent of loss angle
Increase of tan :
0.008
Compared to values measured in 4.15.1.
50 % of values specified in section
“Insulation resistance” of this
specification
Insulation resistance
Resonance frequency
SUB-GROUP C5
D
4.16 Radio frequency characteristic
As specified in section “Resonant
frequency” of this specification. 10 %
Revision: 21-Sep-16
Document Number: 28115
10
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not Recommended for New Designs - Use MKP338 6 Y2
MKP336 6 Y2
Vishay BCcomponents
www.vishay.com
GROUP C INSPECTION REQUIREMENTS
D
OR
ND
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C6
D
4.17 Passive flammability
Class B
Bore of gas jet: Ø 0.5 mm
Fuel: Butane
Test duration for actual volume V in mmꢁ:
V 250: 10 s
After removing test flame from capacitor,
the capacitor must not continue to burn
for more than 10 s. No burning particle
must drop from the sample.
250 < V 500: 20 s
500 < V 1750: 30 s
V > 1750: 60 s
One flame application
12 mm
~ 8 mm
.50ꢀ°
SUB-GROUP C7
D
4.18 Active flammability
20 x 5 kV discharges on the test capacitor
connected to UR
The cheese cloth around the capacitors
shall not burn with a flame.
No electrical measurements are required.
Revision: 21-Sep-16
Document Number: 28115
11
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
Document Number: 91000
1
相关型号：
BFC233810103
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 0.01 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT
VISHAY
BFC233810104
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 0.1 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT
VISHAY
BFC233810105
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 1 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT
VISHAY
BFC233810124
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 0.12 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT
VISHAY
BFC233810153
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 0.015 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT
VISHAY
BFC233810154
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 0.15 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT
VISHAY
BFC233810183
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 0.018 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT
VISHAY
BFC233810184
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 0.18 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT
VISHAY
BFC233810223
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000 V, 0.022 uF, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT
VISHAY
©2020 ICPDF网 联系我们和版权申明