5KP85AHE3/54 [VISHAY]
DIODE 5000 W, UNIDIRECTIONAL, SILICON, TVS DIODE, ROHS COMPLIANT, PLASTIC, CASE P600, 2 PIN, Transient Suppressor;型号: | 5KP85AHE3/54 |
厂家: | VISHAY |
描述: | DIODE 5000 W, UNIDIRECTIONAL, SILICON, TVS DIODE, ROHS COMPLIANT, PLASTIC, CASE P600, 2 PIN, Transient Suppressor 局域网 二极管 电视 |
文件: | 总5页 (文件大小:90K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
5KP8.5A thru 5KP188A
Vishay General Semiconductor
www.vishay.com
®
TRANSZORB Transient Voltage Suppressors
FEATURES
• P600 glass passivated chip junction
• Available in uni-directional polarity only
• 5000 W peak pulse power capability with
a 10/1000 μs waveform, repetitive rate
(duty cycle): 0.01 %
• Excellent clamping capability
• Very fast response time
P600
• Low incremental surge resistance
• Solder dip 275 °C max. 10 s, per JESD 22-B106
• AEC-Q101 qualified
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
TYPICAL APPLICATIONS
Use in sensitive electronics protection against voltage
PRIMARY CHARACTERISTICS
transients induced by inductive load switching and lighting
on ICs, MOSFET, signal lines of sensor units for consumer,
computer, industrial, automotive, and telecommunication.
VWM
8.5 V to 188 V
9.4 V to 231 V
5000 W
VBR
PPPM
MECHANICAL DATA
PD
8.0 W
Case: Molded epoxy body over passivated junction
IFSM
500 A
Molding compound meets UL 94 V-0 flammability rating
Base P/N-E3
Base P/NHE3 - RoHS compliant, AEC-Q101 qualified
- RoHS compliant, commercial grade
TJ max.
Polarity
Package
175 °C
Uni-directional
P600
Terminals: Matte tin plated leads, solderable per
J-STD-002 and JESD 22-B102
E3 suffix meets JESD 201 class 1A whisker test, HE3 suffix
meets JESD 201 class 2 whisker test
Polarity: Color band denotes cathode end
MAXIMUM RATINGS (TA = 25 °C unless otherwise noted)
PARAMETER
SYMBOL
PPPM
IPPM
LIMIT
5000
UNIT
W
Peak pulse power dissipation with a 10/1000 μs waveform (1)
Peak pulse current with a 10/1000 μs waveform (1)
Power dissipation on infinite heatsink at TL = 75 °C (fig. 5)
Peak forward surge current 8.3 ms single half sine-wave (fig. 5)
Instantaneous forward voltage at 100 A (2)
See next table
8.0
A
PD
W
IFSM
600
A
VF
3.5
V
Operating junction and storage temperature range
TJ, TSTG
-55 to +175
°C
Notes
(1)
Non-repetitive current pulse, per fig. 3 and derated above TA = 25 °C per fig. 2
Measured 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum
(2)
Revision: 24-Jun-14
Document Number: 88308
1
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
5KP8.5A thru 5KP188A
Vishay General Semiconductor
www.vishay.com
ELECTRICAL CHARACTERISTICS (JEDEC REGISTERED DATA) (TA = 25 °C unless otherwise noted)
BREAKDOWN
MAXIMUM
REVERSE
LEAKAGE
AT VWM
MAXIMUM
PEAK PULSE
CURRENT
MAXIMUM
CLAMPING
VOLTAGE AT
IPPM
TEST
CURRENT
IT
STAND-OFF
VOLTAGE
VWM
MAXIMUMTEMP.
COEFFICIENT
OF VBR
VOLTAGE
(1)
DEVICE
TYPE
V
BR AT IT
(V)
(2)
IPPM
(mA)
(V)
(%/°C)
ID (μA)
(A)
VC (V)
MIN.
9.44
10.0
11.1
12.2
13.3
14.4
15.6
16.7
17.8
18.9
20.0
22.2
24.4
26.7
28.9
28.9
31.1
33.3
36.7
40.0
44.4
47.8
50.0
53.3
56.7
60.0
64.4
66.7
71.1
77.8
83.3
86.7
94.4
100
MAX.
10.4
11.1
12.3
13.5
14.7
15.9
17.2
18.5
19.7
20.9
22.1
24.5
26.9
29.5
31.9
31.9
34.4
36.8
40.6
44.2
49.1
52.8
55.3
58.9
62.7
66.3
71.2
73.7
78.6
86.0
92.1
95.8
104
5KP8.5A
5KP9.0A
5KP10A
5KP11A
5KP12A
5KP13A
5KP14A
5KP15A
5KP16A
5KP17A
5KP18A
5KP20A
5KP22A
5KP24A
5KP26A
5KP26A
5KP28A
5KP30A
5KP33A
5KP36A
5KP40A
5KP43A
5KP45A
5KP48A
5KP51A
5KP54A
5KP58A
5KP60A
5KP64A
5KP70A
5KP75A
5KP78A
5KP85A
5KP90A
5KP100A
5KP110A
5KP120A
5KP130A
5KP150A
5KP160A
5KP170A
5KP188A
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
8.5
50
20
347
325
294
275
251
233
216
205
192
181
171
154
141
129
119
119
110
103
93.8
86.1
77.5
72.0
68.8
64.6
60.7
57.4
53.4
51.7
48.5
44.2
41.3
39.7
36.5
34.2
30.9
28.2
25.9
23.9
20.6
19.3
18.2
15.2
14.4
15.4
17.0
18.2
19.9
21.5
23.2
24.4
26.0
27.6
29.2
32.4
35.5
38.9
42.1
42.1
45.4
48.4
53.3
58.1
64.5
69.4
72.7
77.4
82.4
87.1
94
0.078
0.081
0.084
0.086
0.088
0.090
0.092
0.094
0.096
0.097
0.098
0.099
0.100
0.101
0.101
0.101
0.102
0.103
0.104
0.104
0.105
0.105
0.106
0.106
0.107
0.107
0.107
0.108
0.108
0.108
0.108
0.108
0.110
0.110
0.110
0.112
0.112
0.112
0.112
0.112
0.112
0.112
9.0
10.0
11.0
12.0
13.0
14.0
15.0
16.0
17.0
18.0
20.0
22.0
24.0
26.0
26.0
28.0
30.0
33.0
36.0
40.0
43.0
45.0
48.0
51.0
54.0
58.0
60.0
64.0
70.0
75.0
78.0
85.0
90.0
100
15
10
5.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
97.0
103
113
121
126
137
146
162
177
193
209
243
259
275
328
111
111
123
122
135
110
133
147
120
144
159
130
167
185
150
178
197
160
189
209
170
209
231
188
Notes
(1)
(2)
(3)
Pulse test: tp 50 ms
Surge current waveform per fig. 3 and derate per fig. 2
All terms and symbols are consistent with ANSI/IEEE CA62.35
Revision: 24-Jun-14
Document Number: 88308
2
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
5KP8.5A thru 5KP188A
Vishay General Semiconductor
www.vishay.com
ORDERING INFORMATION (Example)
PREFERRED P/N
UNIT WEIGHT (g)
PREFERRED PACKAGE CODE
BASE QUANTITY
DELIVERY MODE
5KP8.5A-E3/54
2.776
54
54
800
800
13" diameter paper tape and reel
13" diameter paper tape and reel
5KP8.5AHE3/54 (1)
2.776
Note
(1)
AEC-Q101 qualified
RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted)
100
150
TJ = 25 °C
Pulse Width (td)
is defined as the Point
where the Peak Current
decays to 50 % of IPPM
Non-Repetitive pulse
waveform shown in Fig. 3
TA = 25 °C
tr = 10 µs
Peak Value
IPPM
10
100
50
0
Half Value -
IPP
2
IPPM
1.0
0.1
10/1000 µs Waveform
as defined by R.E.A.
td
1.0
3.0
4.0
0.1 µs
1.0 µs
10 µs
100 µs
1 ms
10 ms
0
2.0
t - Time (ms)
td - Pulse Width
Fig. 1 - Peak Pulse Power Rating Curve
Fig. 3 - Pulse Waveform
100
100 000
TJ = 25 °C
f = 1.0 MHz
Vsig = 50 mVp-p
75
50
Measured at
Zero Bias
10 000
1000
100
Measured at Stand-Off
Voltage VWM
25
0
1
10
100
200
0
25
50
75
100
125
150 175
200
TJ - Initial Temperature (°C)
VWM - Reverse Stand-Off Voltage (V)
Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature
Fig. 4 - Typical Junction Capacitance
Revision: 24-Jun-14
Document Number: 88308
3
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
5KP8.5A thru 5KP188A
Vishay General Semiconductor
www.vishay.com
8
500
60 Hz
Resistive or
Inductive Load
8.3 ms Single Half Sine-Wave
450
400
350
300
250
200
6
4
L = 0.375" (9.5 mm)
Lead Lengths
2
0
0
25
50
75
100 125
150
175
200
1
10
100
TL - Lead Temperature (°C)
Number of Cycles at 60 Hz
Fig. 5 - Power Derating Curve
Fig. 6 - Maximum Non-Repetitive Forward Surge Current
PACKAGE OUTLINE DIMENSIONS in inches (millimeters)
P600
1.0 (25.4)
MIN.
0.360 (9.1)
0.340 (8.6)
0.360 (9.1)
0.340 (8.6)
0.052 (1.32)
1.0 (25.4)
MIN.
0.048 (1.22)
DIA.
APPLICATION NOTES
The 5KP series of high power transient voltage suppressors
were designed to be used on the output of switching power
supplies. These devices may be used to replace crowbar
circuits. Both the 5 % and 10 % voltage tolerances are
referenced to the power supply output voltage level.
shorting. This will enable the user to reset the breaker or
replace the fuse and continue operation. For this type
operation, it is recommended that a sufficient mounting
surface be used for dissipating the heat generated by the
Transient Voltage Suppressor during the transient or
over-voltage condition.
They are able to withstand high levels of peak current while
allowing a circuit breaker to trip or a fuse blow before
Revision: 24-Jun-14
Document Number: 88308
4
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
Document Number: 91000
1
©2020 ICPDF网 联系我们和版权申明