594D10X0-016B2T [VISHAY]
Solid Tantalum Chip Capacitors TANTAMOUNT, Conformal Coated, Maximum CV, Low ESR; 固体钽电容器芯片的TANTAMOUNT ，保形涂层，最大CV ，低ESR
| 型号： | 594D10X0-016B2T |
| 厂家： | 
VISHAY |
| 描述： | Solid Tantalum Chip Capacitors TANTAMOUNT, Conformal Coated, Maximum CV, Low ESR |
| 文件： | 总9页 (文件大小：195K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
594D
Vishay Sprague
Solid Tantalum Chip Capacitors
®
TANTAMOUNT , Conformal Coated, Maximum CV,
Low ESR
FEATURES
• New extended range offerings.
• Large capacitance rating range.
• Lowest ESR for a surface mount tantalum chip capacitor.
• 100% surge current conditioning for C, D and R cases.
• Terminations: Tin (2) standard.
• 8mm, 12mm tape and reel packaging available per EIA-
481-1 and IEC 286-3. 7” [178mm] standard. 13”
[330mm] available.
• Case code compatibility with EIA 535BAAE and
CECC30801 molded chips.
PERFORMANCE / ELECTRICAL CHARACTERISTICS
Operating Temperature: -55˚C to +85˚C, (to -125˚C with
voltage derating.)
Capacitance Tolerance: ±10%, ±20% standard.
Voltage Rating: 4 WVDC to 50WVDC.
Equivalent Series Resistance: ESR readings measured
at 100kHz, +25°C from 3500 milliohm to 30 milliohm.
Capacitance Range: 1.0µF to 1500µF.
ORDERING INFORMATION
594D
477
X0
004
R
2
T
TYPE
CAPACITANCE
CAPACITANCE DC VOLTAGE RATING
CASE CODE TERMINATION
PACKAGING
TOLERANCE
@ + 85°C
This is expressed in volts.
To complete the three-
digit block, zeros precede
the voltage rating. A
decimal point is indicated
by an "R"
This is expressed in
picofarads.
The first two digits are
the significant figures.
The third is the number
of zeros to follow.
See Ratings
and Case
Codes Table.
2 = 100% Tin
4 = Gold Plated
7 = Hot Solder
Dipped
8 = Solder
Plated (60/40)
Special Order.
X0 = ± 20%
X9 = ± 10%
T = Tape and Reel
7" [178mm] Reel
W = 13” [330mm]Reel
- See Tape and
Reel specifications
(6R3 = 6.3 volts).
Note: Preferred Tolerance and reel sizes are in bold.
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Voltage
substitutions will be marked with the higher voltage rating.
DIMENSIONS in inches [millimeters]
W
Tantalum Wire Nib
Identifies Anode (+)
Terminal
L
Max.
J
Max.
J
Max.
D
B
Ref.
A
H
CASE
CODE
L (Max.)
W
H
A
B
D (Ref.)
J (Max.)
B
C
D
R
0.158
[4.0]
0.281
[7.1]
0.293
[7.5]
0.283
[7.2]
0.110 + 0.012 - 0.016 0.075 + 0.012 - 0.024 0.031 ± 0.012
0.097 ± 0.016
[2.5 ± 0.4]
0.180 ± 0.024
[4.6 ± 0.6]
0.180 ± 0.024
[4.6 ± 0.6]
0.180 ± 0.024
[4.6 ± 0.6]
0.138
[3.5]
0.236
[6.0]
0.253
[6.4]
0.243
[6.2]
0.004
[0.1]
0.004
[0.1]
0.004
[0.1]
0.004
[0.1]
[2.8 + 0.3 - 0.4]
[1.9 + 0.3 - 0.6]
[0.80 ± 0.30]
0.126 ± 0.12
[3.2 ± 0.3]
0.098 ± 0.012
[2.5 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.30]
0.170 ± 0.012
[4.3 ± 0.3]
0.110 ± 0.012
[2.8 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.30]
0.235 ± 0.012
[6.0 ± 0.3]
0.136 ± 0.012
[3.5 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.30]
Note: The anode termination (D less B) will be a minimum of 0.012" [0.3mm].
www.vishay.com
66
For technical questions, contact tantalum@vishay.com
Document Number 40006
Revision 09-Mar-05
594D
Vishay Sprague
RATINGS AND CASE CODES
µF
4V
6.3V
Ext.
10V
16V
Ext.
20V
25V
35V
Ext.
50V
Ext.
Std.
Ext. Std.
Std.
Ext.
Std.
Std.
Ext.
Std.
Ext.
Std.
Std.
1.0
1.5
B
2.2
B
3.3
B
4.7
6.8
10
15
22
33
47
68
100
120
150
180
220
270
330
390
470
560
680
1000
1500
B
B
B
C
D
C
D
R
B
B
C
D
B
C
B
B
C
D
R
C
D
R
B
C
D
B
B
B
B
B
C
C
D
D
B
B
C
C
D
D
R
R
C
C
B*
B
C
R
C
D
R
B
D
C
C/D
D
D
R
R
R
D
C
C/D
D
C*
R
R
C
D
R
R
R
R
R
R
*Preliminary values, contact factory for availability.
STANDARD / EXTENDED RATINGS
Max. DF
@ + 25°C
120 Hz
(%)
Max. ESR
@ + 25°C
100kHz
Max. RIPPLE
100kHz
Irms
Max. DCL
@ + 25°C
(µA)
CAPACITANCE
CASE
CODE
(Ohms)
(µF)
PART NUMBER**
(Amps)
4 WVDC @ + 85°C, SURGE = 5.2 V . . . 2.7 WVDC @ + 125°C, SURGE = 3.4 V
594D336X_004B2T
594D107X_004B2T*
594D157X_004B2T
594D157X_004C2T
594D277X_004D2T
594D337X_004C2T*
594D477X_004C2T
594D477X_004R2T
594D687X_004D2T
594D158X_004R2T
6
8*
8
8
8
8*
10
10
12
20
0.38
0.30*
0.25
0.08
0.06
0.08*
0.075
0.045
0.060
0.030
33
100*
150
150
270
330*
470
470
680
1500
B
B*
B
C
D
C*
C
R
D
R
1.3
4.0*
6.0
0.47
0.53*
0.58
1.17
1.58
1.17*
1.21
2.36
1.58
2.89
6.0
10.8
13.2*
18.8
18.8
27.2
60.0
6.3 WVDC @ + 85°C, SURGE = 8 V . . . 4 WVDC @ + 125°C, SURGE = 5 V
1.4
6.3
7.6
0.47
0.58
1.48
1.37
1.52
1.17
1.58
2.36
1.58
2.24
2.36
2.89
22
100
120
220
220
330
330
390
470
470
680
1000
B
B
C
C
D
C
D
R
D
R
R
R
594D226X_6R3B2T
594D107X_6R3B2T
594D127X_6R3C2T
594D227X_6R3C2T
594D227X_6R3D2T
594D337X_6R3C2T
594D337X_6R3D2T
594D397X_6R3R2T
594D477X_6R3D2T
594D477X_6R3R2T
594D687X_6R3R2T
594D108X_6R3R2T
6
6
8
8
8
8
8
8
10
10
12
16
0.380
0.250
0.085
0.080
0.065
0.080
0.060
0.045
0.060
0.050
0.045
0.030
13.9
13.9
20.8
20.8
24.6
29.6
29.6
42.8
63.0
*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
www.vishay.com
67
Document Number 40006
Revision 09-Mar-05
For technical questions, contact tantalum@vishay.com
594D
Vishay Sprague
STANDARD / EXTENDED RATINGS
Max. DF
@ + 25°C
120 Hz
(%)
Max. ESR
@ + 25°C
100kHz
Max. RIPPLE
100kHz
Irms
Max. DCL
@ + 25°C
(µA)
CAPACITANCE
CASE
CODE
(µF)
PART NUMBER**
(Ohms)
(Amps)
10 WVDC @ + 85°C, SURGE = 13 V . . . 7 WVDC @ + 125°C, SURGE = 8 V
0.50
0.50
B
B
B
B
C
B
C
C
D
C
D
D
R
R
R
594D156X_010B2T
594D336X_010B2T
594D476X_010B2T
594D686X_010B2T
594D686X_010C2T
594D107X_010B2T
594D107X_010C2T
594D157X_010C2T
594D157X_010D2T
594D227X_010C2T
594D227X_010D2T
594D337X_010D2T
594D337X_010R2T
594D477X_010R2T
594D687X_010R2T
0.41
0.41
0.46
0.49
1.05
0.57
1.08
1.11
1.41
1.05
1.52
1.52
2.36
2.36
2.36
1.5
3.3
4.7
6.8
6.8
10
10
15
15
22
22
33
33
47
68
6
6
6
6
6
12
8
8
8
8
8
8
8
10
14
15
33
47
68
68
100
100
150
150
220
220
330
330
470
680
0.40
0.350
0.100
0.250
0.095
0.090
0.075
0.100
0.065
0.065
0.045
0.045
0.045
16 WVDC @ + 85°C, SURGE = 20 V . . . 10 WVDC @ + 125°C, SURGE = 12 V
B
B
C
B
C
C
D
C
D
D
R
R
R
2.4
5.3
15
33
594D156X_016B2T
594D336X_016B2T
594D336X_016C2T
594D476X_016B2T
594D476X_016C2T
594D686X_016C2T
594D686X_016D2T
594D107X_016C2T
594D107X_016D2T
594D157X_016D2T
594D187X_016R2T
594D227X_016R2T
594D337X_016R2T
6
6
6
6
6
6
6
8
8
8
8
0.55
0.500
0.150
0.72
0.39
0.41
0.86
0.34
1.00
0.95
1.26
1.17
1.41
1.33
2.13
2.13
2.13
5.3
7.5
33
47
47
68
7.5
0.110
0.123
0.095
0.080
0.075
0.085
0.055
0.055
0.055
10.9
10.9
16
16
24
28.8
35.2
52.8
68
100
100
150
180
220
330
8
8
20 WVDC @ + 85°C, SURGE = 26 V . . . 13 WVDC @ + 125°C, SURGE = 16 V
0.90
0.90
0.85
0.31
0.31
0.32
0.38
0.86
0.89
1.26
1.33
1.77
4.7
6.8
10
22
22
47
47
100
120
6
6
6
6
6
6
6
8
8
B
B
B
B
C
C
D
D
R
594D475X_020B2T
594D685X_020B2T
594D106X_020B2T
594D226X_020B2T
594D226X_020C2T
594D476X_020C2T
594D476X_020D2T
594D107X_020D2T
0.9
1.4
2.0
4.4
4.4
9.4
9.4
20
0.60
0.150
0.140
0.095
0.085
0.080
24
594D127X_020R2T
25 WVDC @ + 85°C, SURGE = 32 V . . . 17 WVDC @ + 125°C, SURGE = 20 V
3.3
10
15
22
33
47
68
68
100
0.8
2.5
3.8
5.5
8.3
11.8
17
6
6
6
6
6
6
6
6
1.50
0.24
0.31
0.70
0.74
1.05
1.07
1.00
1.60
1.67
594D335X_025B2T
594D106X_025B2T
594D156X_025C2T
594D226X_025C2T
594D336X_025D2T
594D476X_025D2T
594D686X_025D2T
594D686X_025R2T
594D107X_025R2T
B
B
C
C
D
D
D
R
R
0.900
0.220
0.200
0.130
0.130
0.150
0.095
0.090
17
25
8
35 WVDC @ + 85°C, SURGE = 46 V . . . 23 WVDC @ + 125°C, SURGE = 28 V
2.2
4.7
6.8
15
15
22
33
47
B
B
C
C
D
D
R
R
0.8
594D225X_035B2T
594D475X_035B2T
594D685X_035C2T
594D156X_035C2T
594D156X_035D2T
594D226X_035D2T
594D336X_035R2T
594D476X_035R2T
6
6
6
6
6
6
6
6
1.70
1.40
0.43
0.40
0.27
0.27
0.20
0.20
0.22
0.25
0.51
0.52
0.75
0.75
1.12
1.12
1.6
2.4
5.3
5.3
7.7
11.6
16.6
*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
www.vishay.com
68
For technical questions, contact tantalum@vishay.com
Document Number 40006
Revision 09-Mar-05
594D
Vishay Sprague
STANDARD / EXTENDED RATINGS
Max. DF
@ + 25°C
120 Hz
(%)
Max. ESR
Max. RIPPLE
100kHz
Irms
Max. DCL
@ + 25°C
(µA)
@ + 25°C
100kHz
(Ohms)
CAPACITANCE
CASE
CODE
(µF)
PART NUMBER**
(Amps)
50 WVDC @ + 85°C, SURGE = 65 V . . . 33 WVDC @ + 125°C, SURGE = 38 V
B
C
D
R
594D105X_050B2T
594D475X_050C2T
594D685X_050D2T
594D156X_050R2T
0.5
2.4
3.4
7.5
4
6
6
6
3.5
1.0
.45
.35
1.0
4.7
6.8
15
0.16
0.33
0.58
0.85
*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
TYPICAL CURVES @ + 25°C, IMPEDANCE AND ESR VS FREQUENCY
"B" Case
"C" Case
1000
100
10
100
10
IMPEDANCE
ESR
IMPEDANCE
ESR
1.0
15µF, 25 VDC
2.2µF, 35 VDC
1
120µF, 6.3 VDC
0.1
22µF, 6.3 VDC
0.1
0.01
100
100
1K
10K
100K
1M
10M
1K
10K
100K
1M
10M
FREQUENCY IN HERTZ
FREQUENCY IN HERTZ
"R" Case
"D" Case
100
10
100
10
IMPEDANCE
ESR
IMPEDANCE
ESR
1.0
1.0
33µF, 25 VDC
33µF, 35 VDC
390µF, 6.3 VDC
220µF, 6.3 VDC
0.1
0.1
0.01
0.01
100
1K
10K
100K
1M
10M
100
1K
10K
100K
1M
10M
FREQUENCY IN HERTZ
FREQUENCY IN HERTZ
www.vishay.com
69
Document Number 40006
Revision 09-Mar-05
For technical questions, contact tantalum@vishay.com
594D
Vishay Sprague
PERFORMANCE CHARACTERISTICS
6.
Dissipation Factor: The dissipation factor, deter-
mined from the expression 2πfRC, shall not exceed
values listed in the Standard Ratings Table.
1.
Operating Temperature: Capacitors are designed
to operate over the temperature range of
- 55°C to + 85°C.
6.1
7.
Measurements shall be made by the bridge
method at, or referred to, a frequency of 120 Hz
and a temperature of + 25°C.
1.1
Capacitors may be operated to + 125°C with voltage
derating to two-thirds the + 85°C rating.
Leakage Current: Capacitors shall be stabilized at
the rated temperature for 30 minutes.
+ 85°C Rating
+ 125°C Rating
Working
Voltage
(V)
Surge
Voltage
(V)
Working
Voltage
(V)
Surge
Voltage
(V)
Rated voltage shall be applied to capacitors for 5
minutes using a steady source of power (such as a
regulated power supply) with 1000 ohm resistor
connected in series with the capacitor under test to
limit the charging current. Leakage current shall
then be measured.
5.2
8
2.7
4
7
10
13
17
23
33
3.4
5
8
12
16
20
28
38
4.0
6.3
10
16
20
25
35
50
13
20
26
32
46
65
Note that the leakage current varies with applied volt
age. See graph below for the appropriate adjustment
factor.
TYPICAL LEAKAGE CURRENT FACTOR RANGE
2.
3.
DC Working Voltage: The DC working voltage is
the maximum operating voltage for continuous
duty at the rated temperature.
100
Surge Voltage: The surge DC rating is the
maximum voltage to which the capacitors may be
subjected under any conditions, including transients
and peak ripple at the highest line voltage.
+ 125°C
+ 85°C
10
+ 55°C
3.1
3.2
Surge Voltage Test: Capacitors shall withstand
the surge voltage applied in series with a 33 ohm
± 5% resistor at the rate of one-half minute on,
one-half minute off, at + 85°C, for 1000 successive
test cycles.
+ 25°C
1.0
0°C
Following the surge voltage test, the dissipation
factor and the leakage current shall meet the initial
requirements; the capacitance shall not have
changed more than ± 10%.
0.1
4.
Capacitance Tolerance: The capacitance of all
capacitors shall be within the specified tolerance
limits of the normal rating.
- 55°C
4.1
Capacitance measurements shall be made by means
of polarized capacitance bridge. The polarizing volt
age shall be of such magnitude that there shall be no
reversal of polarity due to the AC component. The
maximum voltage applied to capacitors during
measurement shall be 2 volts rms at 120 Hz at +25°C.
If the AC voltage applied is less than one-half volt
rms, no DC bias is required. Accuracy of the bridge
shall be within ± 2%.
0.01
0.001
0
10 20
30 40
Percent of Rated Voltage
50 60 70 80
90 100
5.
Capacitance Change With Temperature: The
capacitance change with temperature shall not
exceed the following percentage of the capacitance
measured at + 25°C:
7.1
7.2
7.3
At + 25°C, the leakage current shall not exceed the
value listed in the Standard Ratings Table.
At + 85°C, the leakage current shall not exceed 10
times the value listed in the Standard Ratings Table.
- 55°C
+ 85°C
+ 125°C
At + 125°C, the leakage current shall not exceed
12 times the value listed in the Standard Ratings Table.
- 10%
+ 10%
+ 12%
www.vishay.com
70
For technical questions, contact tantalum@vishay.com
Document Number 40006
Revision 09-Mar-05
594D
Vishay Sprague
12.1 Following the resistance to soldering heat test,
capacitance,dissipationfactorandDCleakagecurrent
shall meet the initial requirement.
PERFORMANCE CHARACTERISTICS (Continued)
8
ESR (Equivalent Series Resistance)
Measurement shall be made by the bridge method at a
frequency of 100kHz and a temperature of + 25°C.
13.
Marking: The small body area of these capacitors
does not allow elaborate marking schemes. All
required information is present on the carton or
package in which the parts are shipped; in addition,
part number, quantity and date code are indicated on
the reels.
8.1
9.
The equivalent Series Resistance shall not exceed the
value listed in the Standard Ratings Table.
Life Test: Capacitors shall withstand rated DC voltage
applied at + 85°C or two-thirds rated voltage applied at
+ 125°C for 2000 hours.
14.
15.
Terminal Strength: Per IEC-384-3, minimum of 5N
shear force.
9.1
10.
Following the life test, the dissipation factor shall meet
the initial requirement; the capacitance change shall
not exceed ± 10%; the leakage current shall not
exceed 125% of the initial requirement.
Environmental: Mercury, CFC and ODS materials
are not used in the manufacture of these capacitors.
16.
17.
Flammability: Encapsulant materials meet UL94 V0.
Humidity Test: Capacitors will withstand 1000 hours
at + 40˚C, 90% to 95% relative humidity, with no
voltage applied.
Capacitor Failure Mode: The predominant failure
mode for solid tantalum capacitors is increased
leakage current resulting in a shorted circuit. Capaci-
tor failure may result from excess forward or reverse
DC voltage, surge current, ripple current, thermal
shock or excessive temperature.
10.1 Following the humidity test, capacitance change shall
not exceed ± 10% of the initial value, dissipation factor
shall not exceed 150% of the initial requirement;
leakage current shall not exceed 200% of the initial
requirement at + 25˚C.
The increase in leakage is caused by a breakdown of
the Ta2O5 dielectric. For additional information on
leakage failure of solid tantalum chip capacitors, refer
to Vishay Sprague Technical Paper, “Leakage Failure
Mode in Solid Tantalum Chip Capacitors.”
11.
Solderability: Capacitors will meet the solderability
requirements of ANSI/J-STD-002, Test B, Category 3.
12.
Resistance to Soldering Heat: Capacitors mounted
on a substrate will withstand + 260°C for 5 seconds.
GUIDE TO APPLICATION
1.0
Recommended rated working voltage guidelines:
2.0
A-C Ripple Current: The maximum allowable
(-55°C to + 85°C)
ripple current shall be determined from the formula:
Standard Conditions, for example; output filters
P
RESR
Capacitor Voltage Rating (V) Operating Voltage (V)
Irms
=
where,
4
6.3
2.5
3.6
P = Power Dissipation in Watts @ + 25°C as given
inthetableinParagraphNumber6.0(PowerDissipation)
10
16
20
25
6
10
12
15
RESR = The capacitor Equivalent Series Resistance
at the specified frequency.
3.0
A-C Ripple Voltage: The maximum allowable ripple
voltage shall be determined from the formula:
35
50
24
28
P
Vrms = Z
RESR
Severe Conditions, for example; input filters
Capacitor Voltage Rating (V) Operating Voltage (V)
or, from the formula:
4
6.3
2.5
3.3
Vrms = Irms x Z
where,
10
16
20
25
5
8
P = Power Dissipation in Watts @ + 25°C as given in
thetableinParagraphNumber6.0(PowerDissipation).
10
12
RESR = The capacitor Equivalent Series Resistance
35
50
15
24
at the specified frequency.
Z
= The capacitor Impedance at the specified
frequency.
3.1
The sum of the peak AC voltage plus the DC voltage
shall not exceed the DC voltage rating of the capacitor.
www.vishay.com
71
Document Number 40006
Revision 09-Mar-05
For technical questions, contact tantalum@vishay.com
594D
Vishay Sprague
platemethods. TheSolderingProfilechartsshowtypical
recomended time/temperature conditions for soldering.
Preheating is recommended. The recommended
maximum ramp rate is 2°C per second. Attachment with
a soldering iron is not recommended due to the difficulty
of controlling temperature and time at temperature. The
soldering iron must never come in contact with the
capacitor.
GUIDE TO APPLICATION (Continued)
3.2 The sum of the negative peak AC voltage plus the
applied DC voltage shall not allow a voltage reversal
exceeding 10% of the DC working voltage at + 25°C.
4.0 Reverse Voltage: These capacitors are capable of
withstanding peak voltages in the reverse direction
equal to 10% of the DC rating at + 25°C and 5% of the
DC rating at + 85°C.
5.0 Temperature Derating: If these capacitors are to be
operated at temperatures above + 25°C, the
RECOMMENDED REFLOW SOLDERING PROFILE
permissible rms ripple current or voltage shall be
calculated using the derating factors as shown:
Recommended Pb Free Reflow Soldering Profile
245°C
Derating
10 sec
Temperature
+ 25°C
Factor
217°C
1.0
200°C
60 sec
+ 85°C
0.9
150°C
+ 125°C
0.4
60 - 150 sec
Preheat
6.0 Power Dissipation: Power dissipation will be
affected by the heat sinking capability of the mounting
surface. Non-sinusoidal ripple current may produce
heating effects which differ from those shown. It is
important that the equivalent Irms value be
established when calculating permissible operating
levels. (Power dissipation calculated using + 25°C
temperature rise.)
25°C
TIME (seconds)
Large Case Codes: D, R
Recommended Pb Free Reflow Soldering Profile
Maximum Permissible
Power Dissipation
260°C
10 sec
Case
Code
@ + 25°C (Watts)
in free air
217°C
200°C
150°C
B
C
D
R
0.085
0.110
0.150
0.250
60 sec
60 - 150 sec
Preheat
25°C
7.0 Printed Circuit Board Material: The capacitors are
compatible with most commonly used printed circuit
board materials (alumina substrates, FR4, FR5, G10,
PTFE-fluorocarbon and porcelanized steel). If your
desired board material is not shown there, please
contact the Tantalum Marketing Department for
assistance in determining compatibility.
TIME (seconds)
Large Case Codes: B, C
Recommended SnPb Reflow Soldering Profile
225°C
10 sec
8.
Attachment:
183°C
150°C
100°C
8.1 Solder Paste: The recommended thickness of the
solder paste after applications is .007" ± .001"
60 sec
[1.78mm ± .025mm]. Care should be exercised in
selecting the solder paste. The metal purity should be
as high as practical. The flux (in the paste) must be
active enough to remove the oxides formed on the
metallization prior to the exposure to soldering heat.
60 - 90 sec
Preheat
25°C
TIME (seconds)
8.2 Soldering: Capacitors can be attached by
conventional soldering techniques, vapor phase,
convection, infrared reflow wave soldering and hot
All Case Codes
www.vishay.com
72
For technical questions, contact tantalum@vishay.com
Document Number 40006
Revision 09-Mar-05
594D
Vishay Sprague
9.0 Recommended Mounting Pad Geometries: The nib
must have sufficient clearance to avoid electrical
contact with other components. The width dimension
indicated is the same as the maximum width of the
REFLOW SOLDER PADS* in inches [millimeters]
B
capacitor. This is to minimize lateral movement.
C
B
10.0 Cleaning (Flux Removal) After Soldering: The
594D is compatible with all commonly used solvents
such as TES, TMS, Prelete, Chlorethane, Terpene and
aqueous cleaning media. However, CFC/ODS
products are not used in the production of these
devices and are not recommended. Solvents
containing methylene chloride or other epoxy
solvents should be avoided since these will attack
the epoxy encapsulation material.
A
* Pads for B, C and D case codes are otherwise pad compatible with
Type 293D, B, C and D case codes respectively.
PAD
WIDTH
(A)
SEPARATION
(C)
CASE
CODE
METALLIZATION
(B)
0.120
[3.0]
0.136
[3.5]
0.180
[4.6]
0.245
[6.3]
0.065
[1.7]
0.120
[3.1]
0.145
[3.7]
0.145
[3.7]
0.065
[1.7
0.090
[2.3]
0.090
[2.3]
0.090
[2.3]
B
C
D
R
TAPE AND REEL PACKAGING in inches [millimeters]
Top
Cover
Tape
Thickness
R
Min.
Standard orientation is with
the cathode (-) nearest to the
sprocket holes per EIA-481-1
and IEC 286-3.
Carrier
Bending Radius
(Note 2)
Embossment
Units Per Reel
Tape Width
7" [178] Reel
Case Code
Component Pitch
13" [330] Reel
B
C
D
R
12mm
12mm
12mm
12mm
2000
500
500
600
8000
3000
2500
—
4mm
8mm
8mm
8mm
www.vishay.com
73
Document Number 40006
Revision 09-Mar-05
For technical questions, contact tantalum@vishay.com
594D
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
Note: Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
.157 ± .004
[4.0 ± 0.10]
T2
Max.
10 Pitches Cumulative
Tolerance on Tape
± 0.008 [0.2]
Deformation
Between
Embossments
.059 + .004 - 0.0
[1.5 + 0.10 - 0.0]
.069 ± .004
[1.75 ± 0.10]
.024 [0.600]
Max.
.079 ± .002
Embossment
[2.0 ± 0.05]
Top
Cover
Tape
20°
Maximum
A0
.030 [0.75]
Min. (Note 3)
F
W
B1 Max.
(Note 6)
Component
Rotation
K0
B0
.030 [0.75]
Min. (Note 4)
Top
Cover
Tape
(Side or Front Sectional View)
Center Lines
of Cavity
P1
.004 [0.10]
Max.
D1 Min. For Components
.079 x .047 [2.0 x 1.2] and Larger.
(Note 5)
For Tape Feeder
Reference only
including draft.
USER DIRECTION OF FEED
Maximum Cavity
Size (Note 1)
Concentric around B0
(Note 5)
Cathode (-)
Anode (+)
DIRECTION OF FEED
3.937 [100.0]
Tape and Reel Specifications: All case codes are available
on plastic embossed tape per EIA-481-1. Tape reeling per
IEC 286-3 is also available. Standard reel diameter is 7"
[178mm]. 13" [330mm] reels are available and recommended
as the most cost effective packaging method.
20° Maximum
.039 [1.0]
Max.
Component Rotation
Typical
Component
Cavity
Tape
B0
Center Line
.039 [1.0] Max.
The most efficient packaging quantities are full reel increments
on a given reel diameter. The quantities shown allow for the
sealed empty pockets required to be in conformance with
EIA-481-1. Reel size and packaging orientation must be
specified in the Vishay Sprague part number.
Typical
Component
Center Line
9.843 [250.0]
A0
Camber
(Top View)
Allowable Camber to be .039/3.937 [1/100]
Non-Cumulative Over 9.843 [250.0]
(Top View)
TAPE
SIZE
D1 (Min.)
(Note 5)
F
R (Min.)
(Note 2)
T2
(Max.)
B1 (Max.)
(Note 6)
W
P1
A0 B0 K0
12mm
0.059
[1.5]
1.181
[30.0]
0.256
[6.5]
0.323
[8.2]
0.472 ± 0.012
[12.0 ± 0.30]
0.217 ± 0.002 0.157 ± 0.004
[5.5 ± 0.05] [4.0 ± 0.1]
(Note 1)
12mm
0.059
[1.5]
1.181
[30.0]
0.256
[6.5]
0.323
[8.2]
0.945 ± 0.012
[24.0 ± 0.03]
0.453 ± 0.004 0.315 ± 0.004
[11.5 ± 0.03] [8.0 ± 0.1]
Double Pitch
Notes:
1. A0B0K are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body
dimen0sions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of
the cavity (A B0K0) must be within 0.002" [0.05mm] minimum and 0.020" [0.50mm] maximum. The clearance allowed must also prevent
rotation of th0e component within the cavity of not more than 20 degrees.
2. Tape with components shall pass around radius "R" without damage. The minimum trailer length may require additional length to
provide R minimum for 12mm embossed tape for reels with hub diameters approaching N minimum.
3. This dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the
embossed cavities or to the edge of the cavity whichever is less.
4. This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the
carrier tape between the embossed cavity or to the edge of the cavity whichever is less.
5. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
embossment location and hole location shall be applied independent of each other.
6. B1 dimension is a reference dimension for tape feeder clearance only.
www.vishay.com
74
For technical questions, contact tantalum@vishay.com
Document Number 40006
Revision 09-Mar-05
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明