303143-191RABL [VISHAY]
Fixed Resistor, Metal Foil, 0.6W, 191ohm, 245V, 0.05% +/-Tol, -.2,.2ppm/Cel, 3011;型号: | 303143-191RABL |
厂家: | VISHAY |
描述: | Fixed Resistor, Metal Foil, 0.6W, 191ohm, 245V, 0.05% +/-Tol, -.2,.2ppm/Cel, 3011 固定电阻器 |
文件: | 总7页 (文件大小:407K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
303143, 303143L (Z-Foil)
Vishay Foil Resistors
Models 303143 and 303143L (Ultra High Precision Fixed
Resistor Z-Foil Z201), Screen/Test Flow as modified
from S-311-P813 Proposed by NASA
FEATURES
Temperature coefficient of resistance (TCR):
0.05 ppm/°C typical (0 °C to + 60 °C)
0.2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C ref.)
Power coefficient of resistance “R due to self heating”:
5 ppm at rated power
Rated power: 0.6 W at 70 °C
0.3 W at 125 °C
Resistance tolerance: to 0.005 %
Load life stability: to 0.005 % at 70 °C, 2000 h at rated
power
INTRODUCTION
Resistance range: 10 to 100 k
The 303143 (0.150" lead spacing) and 303143L (0.200"
lead spacing) Bulk Metal® Z-Foil resistors represent the 3rd
in a series of ultra-precision resistors since the first Bulk
Metal Foil resistor was introduced by Vishay in 1962. Each
represents an improvement on the earlier model. The TCR
slope of the 303143 and 303143L is 0.2 ppm/C (- 55 °C to
+ 125 °C, + 25 °C ref.) and is an order of magnitude better
than the original S102C. The Bulk Metal Z-Foil resistor is the
ultimate choice in the most demanding analog applications.
Electrostatic discharge (ESD) up to 25 000 V
Non-inductive, non-capacitive design
Rise time: 1.0 ns effectively no ringing
Current noise: 0.010 µVRMS/V of applied voltage (< - 40 dB)
Thermal EMF: 0.1 µV/°C max.
0.05 µV/°C typical
Voltage coefficient: < 0.1 ppm/V
Non-inductive: 0.08 µH
Terminal finish: tin/lead alloy
Maximum working voltage: 245 V
Drop in replacement for S102C/K
Matched sets are available per request
The Z-Foil technology provides a significant reduction of the
resistive component’s sensitivity to ambient temperature
variations (TCR) and applied power changes (PCR).
Designers can now guarantee a high degree of stability and
accuracy in fixed-resistor applications using solutions based
on Vishay’s revolutionary Z-Foil technology.
For prototype units, append a “U” to the model number
(example: 303143U). These units include only the 100 %
screening requirements (table 4, page 4). For more
information, please contact foil@vishaypg.com
Our application engineering department is available to
advise and to make recommendations.
FIGURE 1 - POWER DERATING CURVE
- 55 °C
+ 70 °C
200 %
175 %
150 %
125 %
100 %
75 %
50 %
25 %
0
Double Rated Power
TABLE 1 - TOLERANCE AND TCR VS.
RESISTANCE
TYPICAL TCR AND
TIGHTEST
MAXIMUM SPREAD
VALUE
ABSOLUTE
- 55 °C TO + 125 °C
(+ 25 °C ref.)
Rated Power
TOLERANCES
Safe Operation
for < 150 ppm
ΔR after
100 to 100 k
80 to < 100
50 to < 80
25 to < 50
10 to < 25
0.005 %
0.005 %
0.005 %
0.01 %
0.2 0.6 ppm/°C
0.2 0.8 ppm/°C
0.2 1.0 ppm/°C
0.2 1.3 ppm/°C
0.2 1.6 ppm/°C
2000 h
Load Life
- 75 - 50 - 25
0
+ 25 + 50 + 75 + 100 + 125 + 150 + 175 + 200
Ambient Temperature (°C)
0.05 %
Document Number: 63174
Revision: 29-Mar-10
For any questions, contact: foil@vishaypg.com
www.foilresistors.com
1
303143, 303143L (Z-Foil)
Vishay Foil Resistors
FIGURE 2 - TRIMMING TO VALUES
FIGURE 3 - TYPICAL RESISTANCE/
TEMPERATURE CURVE
(conceptual illustration)
+ 500
+ 400
+ 300
+ 200
Interloop
Current Path
Before Trimming
Capacitance
Reduction
in Series
+ 100
ΔR
R
0
- 100
- 200
- 300
- 400
- 500
Current Path
After Trimming
Mutual
(ppm)
Inductance
Reduction due
to Opposing
Current in
0.05 ppm/°C
- 0.1 ppm/°C 0.1 ppm/°C
0.14 ppm/°C
Trimming Process
Removes this Material
from Shorting Strip Area
Changing Current Path
and Increasing Resistance
Adjacent Lines
- 0.16 ppm/°C
0.2 ppm/°C
- 55
- 25
0
+ 25
+ 60 + 75 + 100 + 125
Ambient Temperature (°C)
Note: Foil shown in black, etched spaces in white
FIGURE 4 - STANDARD IMPRINTING AND DIMENSIONS
Front View
Rear View
Optional Customer Part Number
Print Specification, etc. if required
L
W
Date Code
Resistance
Value Code
07
16
VISHAY
XXXX
303143
XXXXXX
100R01
0.005%
Year Week
H
Tolerance
*
ST
SW
LL
Model No.
LS
Lead Material #22 AWG
Round Solder Coated Copper
* The standoffs shall be so located as to give a lead clearance of 0.010" minimum between the resistor body and the printed circuit board
when the standoffs are seated on the printed circuit board. This is to allow for proper cleaning of flux and other contaminants from the unit
after all soldering processes.
LS
W
L
H
ST
SW
LL
Inches 0.150 0.005
303143
mm
Inches 0.200 0.005
mm 5.08 0.13
3.81 0.13
0.105 0.010 0.300 0.010 0.326 0.010
2.67 0.25 7.62 0.25 8.28 0.25
0.010 min
0.254 min
0.035 0.01
1.02 0.13
1.000 0.125
25.4 3.18
303143L
TABLE 2 - SPECIFICATIONS
Stability
0.005 % max. R at 0.1 W/+ 70 °C
Load Life at 2000 h
Load Life at 10 000 h
0.015 % max. R at 0.3 W/+ 125 °C
0.01 % max. R at 0.05 W/+ 125 °C
0.05 % max. R at 0.3 W/+ 125 °C
www.foilresistors.com
2
For any questions, contact: foil@vishaypg.com
Document Number: 63174
Revision: 29-Mar-10
303143, 303143L (Z-Foil)
Vishay Foil Resistors
TABLE 3 - ENVIRONMENTAL PERFORMANCE COMPARISON
VISHAY 303143, 303143L
MIL-PRF-55182
CHAR J
MAXIMUM R
TYPICAL R
Test Group I
Thermal Shock
0.2 %
0.2 %
0.01 % (100 ppm)
0.03 % (300 ppm)
0.002 % (20 ppm)
0.003 % (30 ppm)
Short Time Overload
Test Group II
Resistance Temperature
Characteristic
Low Temperature Storage
Low Temperature Operation
Terminal Strength
25 ppm/°C
see table 1
0.05 ppm/°C
(0 °C to + 60 °C)
0.002 % (20 ppm)
0.002 % (20 ppm)
0.002 % (20 ppm)
0.15 %
0.15 %
0.2 %
0.01 % (100 ppm)
0.01 % (100 ppm)
0.01 % (100 ppm)
Test Group III
DWV
0.15 %
0.1 %
0.4 %
0.01 % (100 ppm)
0.01 % (100 ppm)
0.02 % (200 ppm)
0.002 % (20 ppm)
0.005 % (50 ppm)
0.01 % (100 ppm)
Resistance to Solder Heat
Moisture Resistance
Test Group IV
Shock
Vibration
0.2 %
0.2 %
0.01 % (100 ppm)
0.01 % (100 ppm)
0.002 % (20 ppm)
0.002 % (20 ppm)
Test Group V
Life Test at 0.3 W/+ 125 °C
2000 h
0.5 %
2.0 %
0.015 % (150 ppm)
0.05 % (500 ppm)
0.01 % (100 ppm)
0.03 % (300 ppm)
10 000 h
Test Group Va
Life Test at 0.6 W (2 x Rated Power)/+ 70 °C, 2000 h
0.5 %
2.0 %
0.015 % (150 ppm)
0.05 % (500 ppm)
< 0.00001 %/V
0.01 % (100 ppm)
0.02 % (200 ppm)
< 0.00001 %/V
Test Group VI
High Temperature Exposure
Test Group VII
Voltage Coefficient
0.005 %/V
STANDARD MEASUREMENT (at room temperature)
Standard Test Conditions:
Temperature: + 23 °C 2 °C
Relative humidity: 35 % RH to 65 % RH
Lead test point: 0.5" (12.7 mm) from resistor body
NOTES
For unqualified pre-flight or prototype units, use models # 303143U, 303143LU which include only the 100 % screening
requirements
Measurement error allowed for R limits: 0.01
Document Number: 63174
Revision: 29-Mar-10
For any questions, contact: foil@vishaypg.com
www.foilresistors.com
3
303143, 303143L (Z-Foil)
Vishay Foil Resistors
TABLE 4 - SCREENING AND ENVIRONMENTAL TESTS
Group A
100 %
RC record - in tolerance
Thermal shock (MIL-STD-202 method 107 condition F-1) 25 x, - 65 °C, + 150 °C
Overload (+ 25 °C, 6.25 x rated power, 5 s)
RC record - in tolerance, R = 0.03 %
Power conditioning (+ 125 °C, 0.3 W, 100 h, not to exceed 245 V)
RC record - in tolerance, R = 0.05 %
Visual inspection
Subgroup 1
Final inspection - PDA - 5 % on R = 0.05 %
6 pieces, any value, electrical rejects allowed
Subgroup 2
Subgroup 3
Solderability
3 pieces, any value, non destructive
Mechanical/dimensional evaluation
Final Group A inspection
Group B
13 pieces or 100 %, any value, zero rejects allowed
TCR (MIL-STD-202 method 304 with the following exceptions)
- must maintain temperature for 30 min to 45 min before measurement
- first test temperatures, + 25 °C, - 15 °C, - 55 °C
- second test temperatures, + 25 °C, + 65 °C, + 125 °C
- + 25 °C to be used as reference reading
Subgroup 1
8 pieces, any value, zero rejects allowed
Subgroup 2
Group C
Resistance to solvents
Group A and B testing required
12 pieces (6 of the highest value, 6 of the lowest value), 0 rejects
Life - (+ 125 °C, 0.3 W, not to exceed max. voltage 245 V, 10 000 h)
RC record at 250 h, 500 h, 1000 h, 2000 h, 4000 h, 6000 h, 8000 h, and 10 000 h
Maximum R - 0.015 % for 2000 h, 0.05 % for 10 000 h
Subgroup 1
10 pieces (5 high, 5 low), 1 reject allowed
Resistance to soldering heat (conditions A and C), max. R = 0.01 %
Moisture resistance, max. R = 0.02 %
Subgroup 2
DWV (300 VRMS, 100 V/s, 1 min, R = 0.01 %
Insulation resistance (500 VDC, 2 min, 100 M)
12 pieces (6 high, 6 low), 1 reject allowed
Dielectric withstanding voltage (DWV) (MIL-STD-202 method 301)
- 300 VRMS, 100 V/s, 1 min (with special fixture requirements)
RC record - R = 0.01 %
Insulation resistance (MIL-STD-202 method 302)
- same fixture requirements as DWV
- 500 VDC, 2 min
Subgroup 3
- 10 000 M min.
Low temperature storage (LTS) (- 65 °C , 24 h, 0 W)
Low temperature operation (LTO) (- 65 °C, 45 min, rated V, not to exceed P)
RC record - R = 0.01 % for both LTS and LTO
Terminal strength (MIL-STD-202 method 211)
Pull test (condition A, 2 lbf, 5 s to 10 s)
Twist test (condition D)
RC record - R = 0.01 %
www.foilresistors.com
4
For any questions, contact: foil@vishaypg.com
Document Number: 63174
Revision: 29-Mar-10
303143, 303143L (Z-Foil)
Vishay Foil Resistors
TABLE 4 - SCREENING AND ENVIRONMENTAL TESTS
9 pieces (any value), 0 rejects
Subgroup 4
Shock (method 213, condition I - 100G, 6 ms, sawtooth), R = 0.01 %
Vibration (method 204, condition D, 10 Hz to 2 kHz, 20G), R = 0.01 %
5 pieces (any value), 0 rejects
Subgroup 5
High temperature exposure (2000 h, + 175 °C, 0 W)
RC record - R = 0.05 %
TABLE 5 - QUALIFICATION (10R TO 100K) (when required)
Group 1
Group A
Group 2
Group B
10 pieces (equally divided between highest and lowest values), 1 reject
TCR (per group B conditions)
Low temperature storage (LTS)
Low temperature operation (LTO)
Group 3
RC record - R = 0.01 % for LTS and LTO
Terminal strength (per group C conditions)
Pull test (condition A, 2 lbs, 5 s to 10 s)
Twist test (condition D)
RC record - R = 0.01 %
12 pieces (equally divided between highest and lowest values), 1 reject
Dielectric withstanding voltage (DWV) (MIL-STD-202 method 301)
- 300 VRMS, 100 V/s, 1 min
RC record - R = 0.01 %
Insulation resistance (MIL-STD-202 method 302)
- 10 000 M min.
Group 4
- 500 VDC, 2 min
Resistance to soldering heat (R = 0.01 %)
Moisture resistance (R = 0.05 %)
DWV (300 V, 1 min, R = 0.01 %)
Insulation resistance (500 VDC, 2 min, 100 M)
10 pieces (equally divided between highest and lowest values), 1 reject
Group 5
Shock - (100G, 6 ms, sawtooth condition I), R = 0.01 %
Vibration - (10 Hz to 2 kHz, condition D), R = 0.01 %
10 pieces (equally divided between highest and lowest values), 1 reject
Group 6
Group 7
Solderability
Resistance to solvents
10 pieces (equally divided between highest and lowest values), 1 reject
High temperature exposure (2000 h, + 175 °C, 0 W), R = 0.05 %
50 pieces (equally divided between highest and lowest values), 0 reject
Life - (+ 125 °C, 0.3 W, not to exceed max. voltage 245 V, 10 000 h)
RC record at 250 h, 500 h, 1000 h, 2000 h, 4000 h, 6000 h, 8000 h, and 10 000 h
Maximum R - 0.015 % for 2000 h, 0.05 % for 10 000 h
30 pieces (high/low)
Group 8
Group 9
Thermal shock - 100 cycles, - 65 °C to + 150 °C, R = 0.035 %
10 pieces (highest value only)
Group 10
Voltage coefficient (R = 1 ppm/V)
Document Number: 63174
Revision: 29-Mar-10
For any questions, contact: foil@vishaypg.com
www.foilresistors.com
5
303143, 303143L (Z-Foil)
Vishay Foil Resistors
PART NUMBER IDENTIFICATION
Model #
303143 (1)
Z201
303143L (2)
Z201
Base Model
Value Range (Space Applications)
10 to 100 k
10 to 100 k
Part Number:
{Model}
-
{Value}
-
{Tolerance}
-
{Termination}
-
{Packaging}
Absolute Tolerance
Code
Termination
Code
Packaging
Code
0.005 %
0.01 %
0.02 %
0.05 %
0.1 %
V
T
Tin/lead
B
Bulk
L
Q
A
B
C
D
F
0.25 %
0.5 %
1.0 %
Example: 303143
- 8K023 - VBL
Z201, 8.023 k, 0.005 %, tin/lead termination, bulk pack
Notes
(1) For unqualified pre-flight or prototype units, use model #303143U which includes only the 100 % screening requirements
(2) 0.200" (5.08 mm) lead spacing available - specify 303143L
www.foilresistors.com
6
For any questions, contact: foil@vishaypg.com
Document Number: 63174
Revision: 29-Mar-10
Legal Disclaimer Notice
Vishay Precision Group
Disclaimer
ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their
behalf (collectively, “Vishay Precision Group”), disclaim any and all liability for any errors, inaccuracies or
incompleteness contained herein or in any other disclosure relating to any product.
The product specifications do not expand or otherwise modify Vishay Precision Group’s terms and conditions of
purchase, including but not limited to, the warranty expressed therein.
Vishay Precision Group makes no warranty, representation or guarantee other than as set forth in the terms
and conditions of purchase. To the maximum extent permitted by applicable law, Vishay Precision Group
disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability,
including without limitation special, consequential or incidental damages, and (iii) any and all implied
warranties, including warranties of fitness for particular purpose, non-infringement and merchantability.
Information provided in datasheets and/or specifications may vary from actual results in different applications
and performance may vary over time. Statements regarding the suitability of products for certain types of
applications are based on Vishay Precision Group’s knowledge of typical requirements that are often placed on
Vishay Precision Group products. It is the customer’s responsibility to validate that a particular product with the
properties described in the product specification is suitable for use in a particular application.
No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by
any conduct of Vishay Precision Group.
The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise
expressly indicated. Customers using or selling Vishay Precision Group products not expressly indicated for use
in such applications do so entirely at their own risk and agree to fully indemnify Vishay Precision Group for any
damages arising or resulting from such use or sale. Please contact authorized Vishay Precision Group personnel
to obtain written terms and conditions regarding products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document No.: 63999
Revision: 27-Apr-11
www.vishaypg.com
1
相关型号:
303143-191RFBL
Fixed Resistor, Metal Foil, 0.6W, 191ohm, 245V, 1% +/-Tol, -.2,.2ppm/Cel, 3011
VISHAY
303143-196RFBL
Fixed Resistor, Metal Foil, 0.6W, 196ohm, 245V, 1% +/-Tol, -.2,.2ppm/Cel, 3011
VISHAY
303143-19K30-TBL
Fixed Resistor, Metal Foil, 0.3W, 19300ohm, 245V, 0.01% +/-Tol, 0.2ppm/Cel, Through Hole Mount, 3011, RADIAL LEADED
VISHAY
303143-19K6DBL
Fixed Resistor, Metal Foil, 0.6W, 19600ohm, 245V, 0.5% +/-Tol, -.2,.2ppm/Cel, 3011
VISHAY
303143-19K8ABL
Fixed Resistor, Metal Foil, 0.6W, 19800ohm, 245V, 0.05% +/-Tol, -.2,.2ppm/Cel, 3011
VISHAY
303143-19R6ABL
Fixed Resistor, Metal Foil, 0.6W, 19.6ohm, 245V, 0.05% +/-Tol, -.2,.2ppm/Cel, 3011
VISHAY
303143-1K050-QBL
Fixed Resistor, Metal Foil, 0.3W, 1050ohm, 245V, 0.02% +/-Tol, 0.2ppm/Cel, Through Hole Mount, 3011, RADIAL LEADED
VISHAY
303143-246RBBL
Fixed Resistor, Metal Foil, 0.6W, 246ohm, 245V, 0.1% +/-Tol, -.2,.2ppm/Cel, 3011
VISHAY
303143-255R0-BBL
Fixed Resistor, Metal Foil, 0.3W, 255ohm, 245V, 0.1% +/-Tol, 0.2ppm/Cel, Through Hole Mount, 3011, RADIAL LEADED
VISHAY
303143-255R0-CBL
Fixed Resistor, Metal Foil, 0.3W, 255ohm, 245V, 0.25% +/-Tol, 0.2ppm/Cel, Through Hole Mount, 3011, RADIAL LEADED
VISHAY
303143-255R0-DBL
Fixed Resistor, Metal Foil, 0.3W, 255ohm, 245V, 0.5% +/-Tol, 0.2ppm/Cel, Through Hole Mount, 3011, RADIAL LEADED
VISHAY
303143-255R0-FBL
Fixed Resistor, Metal Foil, 0.3W, 255ohm, 245V, 1% +/-Tol, 0.2ppm/Cel, Through Hole Mount, 3011, RADIAL LEADED
VISHAY
©2020 ICPDF网 联系我们和版权申明