V375B5T200AL2 [VICOR]
DC-DC Regulated Power Supply Module, 1 Output, 200W, Hybrid;型号: | V375B5T200AL2 |
厂家: | VICOR CORPORATION |
描述: | DC-DC Regulated Power Supply Module, 1 Output, 200W, Hybrid |
文件: | 总8页 (文件大小:374K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Data Sheet
*
375V Input Mini Family
DC-DC Converter Module
45
Features
• DC input range: 250 - 425V
• Input surge withstand: 500V for 100ms
• DC output: 2V - 48V
• Programmable output: 10 to 110%
• Regulation: ±0.2% no load to full load
• Efficiency: Up to 89%
• Maximum operating temperature:
100°C at full load
• Power density: Up to 120W/cubic inch
• Height above board: 0.43 in. (10,9 mm)
• Parallelable, with N+M fault tolerance
• Low noise ZCS/ZVS architecture
Shown actual size:
2.28 x 2.2 x 0.5 in
57,9 x 55,9 x 12,7 mm
Typical Applications: distributed power;
off-line systems using power PFC front-ends;
electric vehicles
Product Overview
This DC-DC converter module uses
Absolute Maximum Ratings
2nd Generation power processing, control
and packaging technologies to provide the
performance, flexibility and cost effectiveness
expected of a mature power component.
For example, a plated-cavity core transformer
couples widely separated primary and
secondary windings, resulting in low in-to-
out parasitic capacitance and noise. High
frequency ZCS/ZVS switching, advanced
power semiconductor packaging and thermal
management provide high power density
with low temperature gradients. Extensive
use of silicon integration results in 1/3 the
part count of a 1st Generation converter.
Parameter
Rating
-0.5 to +425
500
Unit
Vdc
Notes
+In to –In voltage
+In to –In voltage
Vdc
<100ms
PC to –In voltage
-0.5 to +7.0
-0.5 to +7.0
-0.5 to +1.5
1.0
Vdc
PR to –In voltage
Vdc
SC to –Out voltage
Vdc
–Sense to –Out voltage
Isolation voltage (in to out)
Isolation voltage (in to base)
Isolation voltage (out to base)
Storage temperature
Operating temperature
Pin soldering temperature
Pin soldering temperature
Mounting torque
Vdc
3000
Vrms
Vrms
Vrms
°C
1550
500
-40 to +125
-20 to +100
500 (260)
750 (390)
5 (0.57)
C-Grade
°C
C-Grade
Part Numbering
°F (°C)
°F (°C)
in-lbs (N-m)
<5 sec; wave solder
<7 sec; hand solder
6 each, # 4-40 or M3
V 375 B 5 C 200 A
Output
Pin
Style
Output
Power
Input Voltage
Voltage
24=24Vin
48=48Vin
Base-
plate
Product Grade Temperatures (°C)
300=300Vin
375=375Vin
Grade
Storage
Operating
20 to +100
40 to +100
40 to +100
55 to +100
Thermal Resistance and Capacity
C
T
H
M
=
=
=
=
-
-
-
-
40 to +125
40 to +125
55 to +125
65 to +125
-
-
-
-
A = Maxi
B = Mini
C = Micro
Parameter
Min
Typ
0.16
0.14
8.0
Max
Unit
°C/Watt
Baseplate to sink; flat, greased surface
Baseplate to sink; thermal pad (P/N 20264)
Baseplate to ambient
For pin styles see page 6. Slotted baseplate
(style 1) requires no designator. For
threaded baseplate add a “2” to the end of
the part number. For thru-hole, add a “3”.
See page 7 for dimensions.
°C/Watt
°C/Watt
Baseplate to ambient; 1000 LFM
Thermal capacity
1.9
°C/Watt
83
Watt-sec/°C
* The modules described here are the highest power for each output voltage.
Consult factory for availability of lower power units.
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
375V Mini Family
Rev. 6.4
Page 1 of 8
Set your site on VICOR at www.vicorpower.com
ELECTRICAL CHARACTERISTICS
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature,
unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate.
MODULE OPERATING SPECIFICATIONS
Parameter
Min
Typ
Max
425
500
Unit
Vdc
Vdc
Notes
Operating input voltage
Input surge withstand
250
375
<100ms
Output voltage setpoint
±1
% Vout nom.
Nominal input; full load; 25°C
MODULE OUTPUT VOLTAGE RELATED SPECIFICATIONS
Parameter
1.8V1 2V
2.5V2 3.3V
75
5V
12V
15V 24V 28V
48V
Unit
Notes
Efficiency (typ.)
71
72
77.7 81.5
84
110 150
200 300
86
87
87.5
89
%
Nominal input; 80% load; 25°C
Nominal input; full load;
25°C; 20MHz BW
Ripple and noise, p-p (typ.) 100
Output power (max.) 90
Output OVP setpoint (nom.) 2.7
100
100
2.7
100 100
114 150
140 190 130
300 300 300
170
300
mV
Watts
At 100°C baseplate temperature
25°C; recycle input voltage to
restart ( 1 minute off )
4.3
4.3
6.3 14.3 17.8 28.1 32.7
55.7
5.2
Volts
Dissipation, standby (typ.)
Load regulation (max.)
Current limit (typ.)
4.8
0.3
115
4.8
0.3
115
5.1
0.2
5.1
0.2
5.4
0.2
5.5
0.3
5.6
0.3
4.5
0.3
5.5
0.3
Watts
No load; nominal input
0.4 ±% Vout
No load to full load; nominal input
Output voltage 95% of nominal
115 115
115 115
115 115
115 115
115 115 115
115 115 115
115
115
% Iout
% Iout
Short circuit current (typ.)
115
115
Output voltage <250mV
MODULE INPUT SPECIFICATIONS
Parameter
Min
Typ
Max
Unit
Vdc
Vdc
Notes
Undervoltage turn-on
Undervoltage turn-off
242.5
212.2
247.5
204.7
492.2
Overvoltage turn-off/on
446.3
467.5
Vdc
MODULE OUTPUT SPECIFICATIONS
Parameter
Min
Typ
±0.02
±0.002
±2
Max
±0.20
±0.005
±5
Unit
%
Notes
Line regulation
Low line to high line; full load
Over operating temperature range
10 to 100% of full load
Temperature regulation
Power sharing accuracy
% / °C
%
Of nominal output voltage. For trimming below 90%
of nominal, a minimum load of 10% of maximum
rated power may be required.
10
110
Programming range
%
Note: For important information relative to applications where the converter modules are subject to continuous dynamic loading,
contact Vicor applications engineering at 800-927-9474.
1 Nominal 2V output trimmed to 1.8V by adding external 9,000 ohm resistor from the SC pin to
2 Nominal 3.3V output trimmed to 2.5V by adding external 3,125 ohm resistor from the SC pin to
-
S pin. (See Fig. 7)
-S pin. (See Fig. 7)
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
375V Mini Family
Rev. 6.4
Page 2 of 8
Set your site on VICOR at www.vicorpower.com
ELECTRICAL CHARACTERISTICS, continued
MODULE CONTROL SPECIFICATIONS
Parameter
Min
Typ
Max
Unit
Notes
PRIMARY SIDE (PC = Primary Control; PR = Parallel)
PC bias voltage
current limit
5.50
1.5
5.75
2.1
6.00
3.0
Vdc
mA
PC current = 1.0 mA
PC voltage = 5.5V
PC module disable
PC module enable delay
PC module alarm
2.3
2.6
4
2.9
7
Vdc
ms
Must be able to sink ≥4 mA. See Fig. 1
0.5
6.1
Vavg
Volts
mA
UV, OV, OT, module fault. See Figs. 2 and 4
PR load >30 ohms, < 30 pF
PR emitter amplitude
PR emitter current
5.7
150
375
2.4
5.9
PR receiver impedance
PR receiver threshold
PR drive capability
500
2.5
625
2.6
12
ohms
Volts
modules
25°C
Minimum pulse width: 20ns
Without PR buffer amplifier
SECONDARY SIDE (SC = Secondary Control)
SC bandgap voltage
SC resistance
1.21
990
1.23
1000
0.033
0
1.25
Vdc
ohms
µF
Referenced to –Sense
1010
SC capacitance
SC module alarm
Vdc
With open trim; referenced to –Sense. See Fig. 6
MODULE GENERAL SPECIFICATIONS
Parameter
Min
Typ
Max
Unit
Notes
Remote sense (total drop)
Isolation voltage (in to out)
Isolation voltage (in to base)
Isolation voltage (out to base)
0.5
Vdc
0.25V per leg (senses must be closed)
3000
1550
500
Vrms
Vrms
Vrms
Complies with reinforced insulation requirements
Complies with basic insulation requirements
Complies with operational insulation requirements
Isolation resistance (in to out)
Weight
10
3.7 (104)
115
megohms
4 (112) ounces (grams)
°C
Temperature limiting
Agency approvals
100
See Figs. 2 and 4
UL, CSA, TÜV, BABT, CE, VDE
UL1950, CSA950, EN60950, VDE0805, BS7002,
IEC 60950. With a fuse in series with the +Input
Note:
Specifications are subject to change without notice.
The latest data sheets for individual models are available on the Vicor website at www.vicorpower.com.
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
375V Mini Family
Rev. 6.4
Page 3 of 8
Set your site on VICOR at www.vicorpower.com
CONTROL FUNCTIONS - PC PIN
Module Enable/Disable
Module Alarm
The module may be disabled by pulling PC below 2.3V with
respect to the –Input. This may be done with an open collector
transistor, relay, or optocoupler. Multiple converters may be
disabled with a single transistor or relay either directly or via
“OR’ing” diodes. See Figure 1.
The module contains “watchdog” circuitry which monitors
input voltage, operating temperature and internal operating
parameters. In the event that any of these parameters are
outside of their allowable operating range, the module will shut
down and PC will go low. PC will periodically go high and the
module will check to see if the fault (as an example,
overtemperature) has cleared. If the fault has not been cleared,
PC will go low again and the cycle will restart. The SC pin will
go low in the event of a fault and return to its normal state after
the fault has been cleared. See Figures 2 and 4.
Primary Auxiliary Supply
At 5.7V, PC can source up to 1.5mA. In the example shown in
Figure 3, PC powers a module enabled LED.
Input Undervoltage
Input Overvoltage
+Out
+In
PC
+In
PC
Overtemperature
+Out
Auto
Restart
Module Faults
SW1
+S
SC
–S
+S
SC
–S
2-20ms typ.
50Ω
f (V )
IN
SW1, 2, & 3
shown in
"Fault" position
1K
SW2
SW3
PR
–In
Disable
PR
–In
5.7Vdc
(0-3mA)
1.23
Vdc
–Out
–Out
6K
Disable = PC <2.3V
Figure 1—Module enable/disable.
Figure 2—PC/SC module alarm logic.
+In
PC
+Out
Fault
PC
40µs typ.
5.7V
+S
SC
–S
4kΩ
"Module
PR
–In
Enabled"
1.23V
2-20ms typ.
SC
–Out
Figure 3—LED on-state indicator.
Figure 4—PC/SC module alarm timing.
Optocoupler
+In
PC
+In
PC
+Out
+Out
+S
SC
–S
+S
SC
–S
Alarm
4kW
PR
–In
PR
–In
1.00V
–Out
–Out
Figure 5—Isolated on-state indicator.
Figure 6—Secondary side on-state indicator.
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
375V Mini Family
Rev. 6.4
Page 4 of 8
Set your site on VICOR at www.vicorpower.com
CONTROL FUNCTIONS - SC PIN
Output Voltage Programming
The output voltage of the converter can be adjusted or
programmed via fixed resistors, potentiometers or voltage
DACs. See Figures 7 and 8.
+Out
+Out
+S
SC
–S
+S
RU
Trim Up
Error
Amp
Error
SC
Amp
Load
Load
RD
Trim Down
–S
1kΩ
1kΩ
0.033
µF
0.033
µF
–Out
–Out
1.23V
1.23V
1,000 Vout
R
(ohms) =
1,000 (Vout-1.23) Vnom
1.23 (Vout-Vnom)
D
–
1,000
R
(ohms) =
Vnom - Vout
U
Figure 7—Output voltage trim down circuit.
Figure 8—Output voltage trim up circuit.
Trim Down
Trim Up
1. This converter is not a constant power device – it has a
1. The converter is rated for a maximum delivered power. To ensure
that maximum rated power is not exceeded, reduce maximum
output current by the same percentage increase in output voltage.
constant current limit. Hence, available output power is
reduced by the same percentage that output voltage is
trimmed down. Do not exceed maximum rated output current.
2. The trim up resistor must be connected to the +Sense pin.
2. The trim down resistor must be connected to the –Sense pin.
3. Do not trim the converter above maximum trim range
(typically +10%) or the output over voltage
protection circuitry may be activated.
Trim resistor values calculated automatically:
On-line calculators for trim resistor values are available
on the vicor website at: vicorpower.com/tools.html.
Resistor values can be calculated for fixed trim up, fixed
trim down and for variable trim up or down cases for both
1st and 2nd Generation DC-DC converters.
In addition to trimming information, the web site and the
Applications Manual also include design tips, applications
circuits, EMC suggestions, thermal design guidelines and
PDF data sheets for all available Vicor products.
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
375V Mini Family
Rev. 6.4
Page 5 of 8
Set your site on VICOR at www.vicorpower.com
CONTROL FUNCTIONS - PR PIN
Parallel Operation
sharing but is not fault tolerant. Minus In pins must be tied to
the same electric potential. See Figure 9.
The PR pin supports paralleling for increased power with N+1
(N+M) redundancy and phased array capability. Modules of
the same input voltage, output voltage, and power level will
current share if all PR pins are suitably interfaced.
AC coupled single-wire interface. All PR pins are connected
to a single communication bus through 0.001µF (500V)
capacitors. This interface supports current sharing and is fault
tolerant except for the communication bus. See Figure 10.
Compatible interface architectures include the following:
DC coupled single-wire interface. All PR pins are directly
connected to one another. This interface supports current
+In
PC
+Out
+In
PC
+Out
+S
SC
–S
+S
SC
–S
0.001µF
Module
1
Module
1
PR
–In
PR
–In
–Out
–Out
+In
PC
+Out
+In
PC
+Out
+S
SC
–S
+S
SC
–S
0.001µF
Module 2
(up to 12)
Module 2
(up to 12)
PR
–In
PR
–In
–Out
–Out
Ground plane
Ground plane
Figure 10—AC coupled single-wire interface.
Figure 9—DC coupled single-wire interface.
• The +Out and –Out power buses
+In
PC
should be designed to minimize
and balance parasitic impedance
from each module output to the
load.
+Out
+S
–S
+S
SC
–S
Module
1
PR
–In
+Out
+In
PC
–Out
• The +Sense pins should be tied
to the same point on the +Out
power bus; the –Sense pins
should be tied to the same point
on the –Out power bus.
+S
Load
–S
+S
SC
–S
+In
PC
+Out
+S
–S
+S
SC
–S
Module
2
PR
–In
PR
–In
• At the discretion of the power
system designer, a subset of all
modules within an array may be
configured as slaves by shorting
SC to –S.
–Out
–Out
+Sense from
other modules
in the array
+In
PC
+Out
Module
N+1
+S
SC
–S
• OR’ing diodes may be inserted in
series with the +Out pins of each
module to provide
PR
–In
–Out
module output fault tolerance.
Figure 11—N+1 module array output connections.
Figure 12—OR’ing diodes connections.
*
PIN STYLES
Designator
Description
Notes
(None)
Short solder
Requires in-board, mounting
L
S
Long solder
On-board mounting for 0.065" boards
SurfMate or in-board socket mounting
Short ModuMate
N
Long ModuMate
On-board socket mounting
* Pin style designator follows the “A” after the output power and precedes the baseplate designator.
Ex. V375A24C600AN — Long ModuMate Pins
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
375V Mini Family
Rev. 6.4
Page 6 of 8
Set your site on VICOR at www.vicorpower.com
MECHANICAL DRAWINGS
MODULE OUTLINE
Converter Pins
0.50 ±0.02
12,7 ±0,5
No. Function Label
1
+In
+
Primary
Control
2
PC
2.20
55,9
1.74
44,2
0.01
3
4
5
6
Parallel
–In
PR
–
0.23
5,8
(REF)
2.000
50,80
0.10
2,5
style 2 & 3
baseplates only
(4X)***
0.49
12,4
0.12* 0.20**
3,1 5,1
0.300 ±0.015
7,62 ±0,38
–Out
–
0.10
2,5
X 45˚
–Sense
–S
CHAMFER
Secondary
Control
1
9
2
8
3
6
4
5
0.35
(2X)
0.300 ±0.015
7,62 ±0,38
7
SC
0.65
16,5
FULL R (6X)
8,8
2.28
57,9
1.900
48,26
1.30
33,0
ALUMINUM
BASEPLATE
8
9
+Sense
+Out
+S
+
0.130
(6X)
3,30
7
Use a 4-40 Screw (6X)
Torque to:
0.150
DIA,(2X)
0.43
10,9
0.06
1,5
3,81
0.080
2,03
5 in-lbs
.57 N-m
R
(3X)
2.20
55,9
(REF.)
0.400
10,16
DIA,(7X)
0.54
(9X)
13,7
0.700
17,78
Pin Style 1&S
(Short Pin)
1.000
25,40
1.400
35,56
0.62
(9X)
15,7
Slotted (Style 1)
or
Pin Style 2&N
(Long Pin)
Threaded (Style 2)
4-40 UNC-2B (6X)
or
ALL MARKINGS
THIS SURFACE
Thru Hole (Style 3)
#30 Drill Thru (6X)
(0.1285)
*
Style 1 baseplate only
** Style 2 & 3 baseplates
*** Reserved for Vicor accessories
Not for mounting
PCB MOUNTING SPECIFICATIONS
ALUMINUM
INBOARD
SOLDER
MOUNT
ONBOARD
SOLDER
MOUNT
BASEPLATE
PINS STYLES
PIN STYLE 1&S
PIN STYLE 2&N
SHORT & LONG (L) SOLDER:TIN/LEAD
HOT SOLDER DIPPED
0.062 ±0.010
PCB THICKNESS
0.094 ±0.003
2,39 ±0,08
0.094 ±0.003
2,39 ±0,08
(7X)
(2X)
1,57 ±0,25
STYLE S & N: GOLD PLATED COPPER
PLATED
THRU HOLE
DIA
0.164 ±0.003
4,16 ±0,08
0.164 ±0.003
4,16 ±0,08
1.790
45,47
0.06
1,5
R
(4X)
0.158
4,01
1
2
3
4
1.584*
40,23
1.900*
48.,26
9
8
7
6
5
0.400*
Unless otherwise specified,
dimensions are in inches
mm
0.43
10,9
0.53
13,5
10,16
0.700*
17,78
Decimals
Tol.
Angles
1.000*
25,40
1.400*
35,56
0.XX
±0.01
±0.25
±0.005
±0.127
* DENOTES
±1°
±0.003
0.195
4,95
TOL =
0.XXX
±0,08
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
375V Mini Family
Rev. 6.4
Page 7 of 8
Set your site on VICOR at www.vicorpower.com
Vicor’s comprehensive line of power solutions includes modular, high
density DC-DC converters and accessory components, configurable power
supplies, and custom power systems.
Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is
assumed by Vicor for its use. No license is granted by implication or otherwise under any patent or patent
rights of Vicor. Vicor components are not designed to be used in applications, such as life support systems,
wherein a failure or malfunction could result in injury or death. All sales are subject to Vicor’s Terms and
Conditions of Sale, which are available upon request.
Specifications are subject to change without notice.
Component Solutions
45
for Your Power System
Vicor Corporation
25 Frontage Road
Andover, MA, USA 01810
Tel: 800-735-6200
978-470-2900
Fax: 978-475-6715
Email
Vicor Express: vicorexp@vicr.com
Technical Support: apps@vicr.com
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
375V Mini Family
P/N 24247
Rev. 6.4 11/04/10M
Set your site on VICOR at www.vicorpower.com
相关型号:
©2020 ICPDF网 联系我们和版权申明