MIM-5303S5F [UOT]
INFRARED RECEIVER MODULE; 红外线接收器型号: | MIM-5303S5F |
厂家: | UNITY OPTO TECHNOLOGY |
描述: | INFRARED RECEIVER MODULE |
文件: | 总6页 (文件大小:119K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INFRARED RECEIVER MODULE
MIM-5xx3S5F
Description
The MIM-5xx3S5F is miniaturized infrared receivers for
remote control and other applications requiring improved
ambient light rejection.
The separate PIN diode and preamplifier IC are assembled
on a single leadframe.
The epoxy package contains a special IR filter.
This module has excellent performance even in disturbed
ambient light applications and provides protection against
uncontrolled output pulses.
Features
l Photo detector and preamplifier in one package
l Internal filter for PCM frequency
l High immunity against ambient light
l Improved shielding against electric field disturbance
l 5.0-Volt supply voltage; low power consumption
l TTL and CMOS compatibility
MIM-5xx3S5F Series Models
l MIM-5303S5F 30.0KHz
l MIM-5333S5F 33.0KHz
l MIM-5363S5F 36.0KHz
l MIM-5373S5F 36.7KHz
l MIM-5383S5F 38.0KHz
l MIM-5403S5F 40.0KHz
l MIM-5443S5F 44.0KHz
l MIM-5563S5F 56.0KHz
BLOCK DIAGRAM
VS
CGA &
filter
Demodulator
mC
Input
AGC / ATC & digital
control
Oscillator
GND
REV: A1
Unity Opto Technology Co., Ltd.
12/11/2003
INFRARED RECEIVER MODULE
MIM-5xx3S5F
@ Ta=25oC
Absolute Maximum Ratings
Item
Symbol
Vs
Ratings
-0.3 ~ 6.0
5.0
Unit
V
Remark
Supply voltage
Supply Current
Is
mA
oC
oC
Topr
Tstg
Tsd
Operating temperature
Storage temperature
-25 ~ + 85
-25 ~ + 85
260
Soldering temperature
Power dissipation at Ta=25oC
oC
t≦5 s, 1mm from case
Ptot
30
mW
Electro-optical characteristics (Vcc=5.0V)
Parameter
Supply Voltage
Symbol
Vs
Min.
Typ.
5.0
Max.
5.5
Unit
V
Remarks
4.5
Current consumption
Response wavelength
Tuning frequency
Icc
1.4
2.0
mA
nm
Under no signal
l p
940
f0
See MIM-5xx3S5F series model
Output form
- - - - - active low output - - - - -
V0h
V0l
Twh
Twl
L1
H level output voltage
4.2
V
V
L level output voltage
0.5
H level output pulse width
L level output pulse width
Distance between emitter & detector
Directivity (Half Angle )
400
400
600
600
800
800
ms
ms
10.0
m
Note 1
Dq
±45
deg
Test Method
A. Standard Transmitter
600ms
carrier frequency f0
duty 50%
ON/OFF pulse width satisfied from
25 cm to detection limit
600ms
600ms
Fig 1. Burst Wave
25cm
+5.0V
10kW
10mF
Transmitter
Duty 50%
Vout
GND
Oscilloscope
Fig 2. Standard Transmitter Measurement circuit
REV: A1
12/11/2003
Unity Opto Technology Co., Ltd.
INFRARED RECEIVER MODULE
MIM-5xx3S5F
B. Detection Length Test
q
Vout
Transmitter output
q
D.U.T
q: indicates horizontal and vertical directions
L
C . Pulse Width Test
Transmitter output
DUT output pulse
600ms 600ms
Twl
Twh
V0h
V0l
Application Circuit
100Ω*)
Vcc (+5V)
2
4.7μF *)
MIM-5xx3S5F
>10kΩ
opt i onal
MIE-544A2
μC
1
3
GND
*) recommended to suppress power supply disturbances
REV: A1
Unity Opto Technology Co., Ltd.
12/11/2003
INFRARED RECEIVER MODULE
MIM-5xx3S5F
Dimensions in mm
受光面中心
REV: A1
Unity Opto Technology Co., Ltd.
12/11/2003
INFRARED RECEIVER MODULE
MIM-5xx3S5F
CHARACTERISTIC CURVES (TA=25oC)
900
800
700
600
500
400
1.
Burst length * 600ms, cycle =
1.2ms tpw: Average value of
output from start of signal input
1.
1.
1.2
1.
10
0.1
1
100
1000
6
3
4
5
7
Input Level (mVp-p
)
Supply Voltage Vcc (V)
INPUT LEVEL vs.OUTPUT PULSE WIDTH
SUPPLY VOLTAGE vs. SUPPLY
CURRENT
0∘
15∘
1
30∘
45∘
0.8
1.0
0.8
0.6
0.4
0.2
0
60∘
∘
0.6
750
850
950
1050
1150
0.4
0.2
0
0.1 0.3
λ - Wavelength (nm)
RELATIVE TRANIMISSION
RELATIVE SPECTRAL SENSITIVITY vs
WAVELENGTH
1
0.8
0.6
0.4
0.2
0
f=fo±5%
Δf(3dB) = fo/7
0.7
0.8
0.9
1
1.1
1.2
1.3
f/fo - Relative Frequency
FREQUENCY DEPENDENCE OF
RESPONSIVITY
REV: A1
Unity Opto Technology Co., Ltd.
12/11/2003
INFRARED RECEIVER MODULE
MIM-5xx3S5F
Reliability
Test item
High temparature
High temp. & high humi.
Low temparature
Temperature cycle
Dropping
Test condition
Standard
Note 2.
Note 2.
Note 2.
Note 2.
Note 3.
Ta=+80oC
Ta=+40oC 90%RH
Ta= -30oC
t=240H
t=240H
t=240H
-30oC(0.5H) ~ +80oC(0.5H) 20cycle
Test devices shall be dropped 3 times naturally
onto hard wooden board from a 75cm height position.
NOTE 1. Distance between emitter & detector specifies maximum distance that output wave form satisfies
the standard under the conditions below against the standerd transmitter.
(1)Measuring place ………Indoor without extreme reflection of light.
(2)Ambient light source… Detecting surface illumination shall be 200±50Lux under ordinary
hite fluorescense lamp of no high frequency lighting.
(3)Standard transmitter … Burst wave indicated in Fig 1. of standard transmitter
shall be arranged to 50mVp-p under the measuring circuit specified in Fig 2.
NOTE 2. (electro-optical charactistics) shall be satisfied after leaving 2 hours in the normal temperature .
NOTE 3. (electro-optical charactistics) shall be satisfied and no conoid deforms
and destructions of appearance .(excepting deforms of terminals)
Inspection standard
1.Among electrical characteristics , total number shall be inspected on items blow.
1-1 front distance between emitter & detector
1-2 Current consumption
1-3 H level output voltage
1-4 L level output voltage
2.Items except above mentioned are not inspected particularly , but shall fully satisfy
CAUTION ( When use and storage of this device )
1.Store and use where there is no force causing transformation or change in quality .
2.Store and use where there is no corrosive gas or sea(salt) breeze .
3.Store and use where there is no extreme humidity .
4.Solder the lead-pin within the condition of ratings. After soldering do not add extra force .
5.Do not wash this device . Wipe the stains of diode side with a soft cloth. You can
use the solvent , ethylalcohol or methylalcohol or isupropylene only .
6.To prevent static electricity damage to the Pre-AMP make sure that the human body
, the soldering iron is connected to ground before using .
7.Put decoupling device between Vcc and GND for reduse the noise from power supply line .
8.The performance of remote-control system depends on environments condition and ability
of periferal parts. Customer should evaluate the performance as total system in those conditions
after system up with components such as commander , micon and this receiver module .
Others
1.This device is not design to endure radiative rays and heavily charged particles .
2.In case where any trouble or questions arise,both parties agress to make full discussion
covering the said problem .
REV: A1
Unity Opto Technology Co., Ltd.
12/11/2003
相关型号:
©2020 ICPDF网 联系我们和版权申明