TPD4134K_技术文档

TPD4134K

TOSHIBA Intelligent Power Device

High Voltage Monolithic Silicon Power IC

TPD4134K

The TPD4134K is a DC brush less motor driver using high

voltage PWM control. It is fabricated by high voltage SOI process.

It is three-shunt resistor circuit for current sensing. It contains

level shift high-side driver, low-side driver, IGBT outputs, FRDs

and protective functions for over-current circuit and under

voltage protection circuits and thermal shutdown circuit. It is

easy to control a DC brush less motor by just putting logic inputs

from a MPU or motor controller to the TPD4134K.

HDIP26-P-1332-2.00

Weight: 3.8 g (typ.)

Features

•

High voltage power side and low voltage signal side terminal are separated.

It is the best for current sensing in three shunt resistance.

Bootstrap circuit gives simple high-side supply.

Bootstrap diodes are built in.

A dead time can be set as a minimum of 1.4 μs, and it is suitable for a Sine-wave from drive.

3-phase bridge output using IGBTs.

FRDs are built in.

Included over-current and under-voltage protection, and thermal shutdown.

The regulator of 7 V (typ.) is built in.

Package: 26-pin DIP.

This product has a MOS structure and is sensitive to electrostatic discharge. When handling this product, ensure that

the environment is protected against electrostatic discharge.

Start of commercial production

2010-03

1

2013-11-01

TPD4134K

Pin Assignment

Marking

Lot Code.

(Weekly code)

TPD4123K

TPD4134K

Country of origin

Part No. (or abbreviation code)

2

2013-11-01

TPD4134K

Block Diagram

V

BSU

18

CC

15

13

BSV

21

BSW

24

V

BB

23

7 V

V

REG

Under-

voltage

Under-

voltage

Under-

voltage

Regulator

Protection Protection Protection

Under-

voltage

Protection

High-side Level

Shift Driver

HU

HV

HW

LU

4

5

6

7

8

9

U

V

17

22

Thermal Shutdown

Input Logic

W

25

LV

Low-side

Driver

LW

IS3

IS2

26

20

11

DIAG

IS1

RS

19

10

Over-current

protection

1/16 GND

3

2013-11-01

TPD4134K

Pin Description

Pin No.

Symbol

Pin Description

1

2

3

GND

NC

Ground pin.

Unused pin, which is not connected to the chip internally.

NC

The control terminal of IGBT by the high side of U. It turns off less than 1.5 V.

It turns on more than 2.5 V.

The control terminal of IGBT by the high side of V. It turns off less than 1.5 V.

It turns on more than 2.5 V.

The control terminal of IGBT by the high side of W. It turns off less than 1.5 V.

It turns on more than 2.5 V.

The control terminal of IGBT by the low side of U. It turns off less than 1.5 V.

It turns on more than 2.5 V.

4

5

6

7

8

HU

HV

HW

LU

The control terminal of IGBT by the low side of V. It turns off less than 1.5 V.

It turns on more than 2.5 V.

LV

The control terminal of IGBT by the low side of W. It turns off less than 1.5 V.

It turns on more than 2.5 V.

9

LW

RS

10

11

Over current detection pin.

With the diagnostic output terminal of open drain , a pull-up is carried out by resistance.

It turns on at the time of unusual.

DIAG

NC

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

Unused pin, which is not connected to the chip internally.

7 V regulator output pin.

V

REG

NC

Unused pin, which is not connected to the chip internally.

Control power supply pin. (15 V typ.)

Ground pin.

V

CC

GND

U

BSU

IS1

IS2

BSV

V

U-phase output pin.

U-phase bootstrap capacitor connecting pin.

U-phase IGBT emitter and FRD anode pin.

V-phase IGBT emitter and FRD anode pin.

V-phase bootstrap capacitor connecting pin.

V-phase output pin.

V

High-voltage power supply input pin.

W-phase bootstrap capacitor connecting pin.

W-phase output pin.

BB

BSW

W

IS3

W-phase IGBT emitter and FRD anode pin.

4

2013-11-01

TPD4134K

Equivalent Circuit of Input Pins

Internal circuit diagram of HU, HV, HW, LU, LV, LW input pins

2 kΩ

HU/HV/HW

LU/LV/LW

To internal circuit

6.5 V

Internal circuit diagram of RS pin

V

CC

4 kΩ

442 kΩ

RS

To internal circuit

19.5 V

5 pF

Internal circuit diagram of DIAG pin

DIAG

To internal circuit

26 V

250kΩ

5

2013-11-01

TPD4134K

Timing Chart

HU

HV

HW

LU

LV

Input Voltage

LW

VU

Output voltage VV

VW

6

2013-11-01

TPD4134K

Truth Table

Input

HV HW LU

High side

Low side

DIAG

Mode

HU

H

L

LV

H

L

LW U phase V phase W phase U phase V phase W phase

Normal

L

H

L

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

H

L

OFF

ON

L

H

L

ON

OFF

ON

L

H

L

OFF

ON

L

H

L

ON

OFF

ON

Over-current

H

L

OFF

ON

L

H

L

ON

H

L

ON

L

H

L

ON

L

H

L

ON

L

H

L

ON

Thermal shutdown

H

L

ON

L

H

L

ON

H

L

ON

L

H

L

ON

L

H

L

ON

L

H

L

ON

V

Under-voltage

H

L

ON

CC

L

H

L

ON

H

L

ON

L

H

L

ON

L

H

L

ON

L

H

L

ON

V

H

L

OFF

BS

L

H

L

OFF

ON

H

L

ON

L

H

L

OFF

L

H

L

ON

L

H

L

OFF

7

2013-11-01

TPD4134K

Absolute Maximum Ratings (Ta = 25°C)

Characteristics

Symbol

Rating

Unit

V

500

V

BB

CC

out

Power supply voltage

V

18

Output current (DC)

Output current (pulse 1ms)

Input voltage

I

2

3

A

I

A

outp

V

-0.5 to 7

50

V

IN

V

current

I

mA

V

REG

DIAG voltage

V

20

DIAG

DIAG current

I

20

mA

Power dissipation

P

36

22

W

C(IGBT)

（IGBT1 phase (Tc = 25°C) )

Power dissipation

P

C(FRD)

（FRD1 phase (Tc = 25°C) )

Operating junction temperature

Junction temperature

Storage temperature

T

-40 to 135

150

°C

jopr

T

j

T

-55 to 150

stg

Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the

significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even

if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum

ratings and the operating ranges.

Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook

(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test

report and estimated failure rate, etc).

8

2013-11-01

TPD4134K

Electrical Characteristics (Ta = 25°C)

Characteristics

Symbol

Test Condition

Min

Typ.

Max

Unit

V

⎯

50

13.5

⎯

280

15

450

16.5

0.5

5

BB

CC

BB

CC

Operating power supply voltage

V

I

V

= 450 V

= 15 V

⎯

BB

CC

BS

Current dissipation

Bootstrap Current dissipation

Input voltage

mA

μA

V

I

⎯

0.8

210

180

⎯

I

= 15 V, high side ON

= 15 V, high side OFF

⎯

410

370

⎯

BS (ON)

I

⎯

BS (OFF)

V

= “H”, V

CC

= 15 V

2.5

⎯

IH

IN

V

= “L” , V

CC

⎯

1.5

150

100

3

IL

IN

I

= 5 V

= 0 V

⎯

IH

IN

Input current

μA

V

I

⎯

IL

IN

V

H

= 15 V, I = 1 A, high side

⎯

2.1

1.8

0.8

7

CEsat

CC

C

Output saturation voltage

FRD forward voltage

V

L

= 15 V, I = 1 A, low side

⎯

3

CEsat

V H

C

I

= 1 A, high side

= 1 A, low side

= 500 μA

⎯

2.8

1.2

7.5

0.54

4.4

185

⎯

F

V

V L

F

⎯

BSD forward voltage

V

⎯

V

F (BSD)

Regulator voltage

V

= 15 V, I = 30 mA

REG

6.5

0.46

2.3

135

⎯

REG

CC

Current limiting voltage

Current limiting dead time

Thermal shutdown temperature

Thermal shutdown hysteresis

V

⎯

0.5

3

V

R

Dt

μs

°C

V

TSD

V

= 15 V

⎯

CC

ΔTSD

50

V

under voltage protection

V

UVD

⎯

10

10.5

8

11

12

CC

BS

CC

under voltage protection recovery

under voltage protection

UVR

UVD

UVR

11.5

9

12.5

9.5

10.5

0.5

3

V

BS

under voltage protection recovery

8.5

⎯

9.5

⎯

V

DIAG saturation voltage

Output on delay time

Output off delay time

Dead time

V

I

= 5 mA

DIAG

V

DIAGsat

t

V

= 280 V, V

= 15 V, I = 1 A

⎯

1.5

1.3

⎯

μs

ns

on

BB

CC

C

= 15 V, I = 1 A

⎯

3

off

C

t

= 15 V, I = 1 A

1.4

⎯

dead

C

FRD reverse recovery time

t

= 15 V, I = 1 A

200

⎯

rr

C

9

2013-11-01

TPD4134K

Application Circuit Example

15 V

V

CC

15

18

21

24

23

BSU

BSV

BSW

+

C

5

4

V

BB

Under-

voltage

Under-

voltage

Under-

voltage

7 V

13

Regulator

V

REG

+

Protection Protection Protection

C

7

C

6

Under-

voltage

Protection

High-side

Level Shift

Driver

C

1

C C

2 3

C

4

5

6

7

8

9

HU

HV

HW

LU

17

22

25

Thermal

U

V

Control IC

or

M

Shutdown

Input Logic

Microcomputer

W

Low-side

Driver

LV

LW

IS3

26

20

19

10

11

DIAG

R

2

IS2

IS1

RS

Over-current

protection

R

1

1/16

GND

10

2013-11-01

TPD4134K

External Parts

Typical external parts are shown in the following table.

Part

Typical

Purpose

Remarks

C , C , C

25 V/2.2 μF

0.35 Ω ± 1 % (1 W)

25 V/10 μF

Bootstrap capacitor

Current detection

(Note 1)

(Note 2)

(Note 3)

(Note 4)

1

2

1

4

5

6

7

2

3

R

C

R

V

power supply stability

CC

25 V/0.1 μF

25 V/1 μF

V

for surge absorber

CC

V

power supply stability

REG

25 V/1000 pF

5.1 kΩ

V

for surge absorber

REG

DIAG pull-up resistor

Note 1: The required bootstrap capacitance value varies according to the motor drive conditions. The capacitor is

biased by V and must be sufficiently derated for it.

CC

Note 2: The following formula shows the detection current: I = V ÷ R₁(For V = 0.5 V typ.)

O

R

Do not exceed a detection current of 2 A when using this product.

(Please go from the outside in the over current protection.)

Note 3: When using this product, adjustment is required in accordance with the use environment. When mounting,

place as close to the base of this product leads as possible to improve the ripple and noise elimination.

Note 4: The DIAG pin is open drain. If not using the DIAG pin, connect to the GND.

Handling precautions

(1) Please control the input signal in the state to which the V

voltage is steady. Both of the order of the V

CC

BB

power supply and the V

power supply are not cared about either.

CC

Note that if the power supply is switched off as described above, this product may be destroyed if the

current regeneration route to the V power supply is blocked when the V line is disconnected by a relay

BB

or similar while the motor is still running.

(2) The RS pin connecting the current detection resistor is connected to a comparator in the IC and also

functions as a sensor pin for detecting over current. As a result, over voltage caused by a surge voltage, for

example, may destroy the circuit. Accordingly, be careful of handling the IC or of surge voltage in its

application environment.

11

2013-11-01

TPD4134K

Description of Protection Function

(1) Over-current protection

This product incorporates a over-current protection circuit to protect itself against over-current at

startup or when a motor is locked. This protection function detects voltage generated in the current

detection resistor connected to the RS pin. When this voltage exceeds V (=0.5 V typ.), the IGBT

R

output, which is on, temporarily shuts down after a dead time , preventing any additional current

from flowing to this product. The next all “L” signal releases the shutdown state.

(2) Under voltage protection

This product incorporates under voltage protection circuits to prevent the IGBT from operating in

unsaturated mode when the V

voltage or the V voltage drops.

BS

CC

When the V

power supply falls to this product internal setting V UVD (=11 V typ.), all IGBT

CC

outputs shut down regardless of the input. This protection function has hysteresis. When the V

CC

power supply reaches 0.5 V higher than the shutdown voltage (V UVR (=11.5 V typ.)), this product is

CC

automatically restored and the IGBT is turned on again by the input. DIAG output is reversed at the

time of V

under-voltage protection. When the V

power supply is less than 7 V, DIAG output isn't

CC

sometimes reversed. When the V

supply voltage drops V UVD (=9 V typ.), the high-side IGBT

BS

output shuts down. When the V

supply voltage reaches 0.5 V higher than the shutdown voltage

BS

(V UVR (=9.5 V typ.)), the IGBT is turned on again by the input signal.

BS

(3) Thermal shutdown

This product incorporates a thermal shutdown circuit to protect itself against the abnormal state

when its temperature rises excessively.

When the temperature of this chip rises to the internal setting TSD due to external causes or internal

heat generation, all IGBT outputs shut down regardless of the input. This protection function has

hysteresis ΔTSD (= 50°C typ.). When the chip temperature falls to TSD − ΔTSD, the chip is

automatically restored and the IGBT is turned on again by the input.

Because the chip contains just one temperature detection location, when the chip heats up due to the

IGBT, for example, the differences in distance from the detection location in the IGBT (the source of

the heat) cause differences in the time taken for shutdown to occur. Therefore, the temperature of the

chip may rise higher than the thermal shutdown temperature when the circuit started to operate.

Timing Chart of Under voltage protection

LIN

HIN

V_BS

V_CC

LO

t_on

t_off

HO

t_on

t_off

DIAG

Note: The above timing chart is considering the delay time

Safe Operating Area

2

1.9

0

400 450

Power supply voltage V (V)

BB

Figure 1 SOA at Tj = 135 °C

Note 1: The above safe operating areas are Tj = 135 °C (Figure 1).

12

2013-11-01

TPD4134K

V

H – T

V

L – T

CEsat

j

3.4

3.0

2.6

2.2

1.8

1.4

3.4

3.0

2.6

2.2

1.8

1.4

V

= 15 V

V

= 15 V

CC

I

= 1.6A

= 1.2A

I

= 1.6A

= 1.2A

C

I

C

I

= 0.8A

= 0.4A

I

= 0.8A

C

= 0.4A

−50

0

50

100

150

18

−50

0

50

100

150

Junction temperature

T

(°C)

Junction temperature

T

(°C)

j

V H – T

F

V L – T

F

j

2.4

2.0

1.6

1.2

0.8

2.4

2.0

1.6

1.2

0.8

I

= 1.6A

= 1.2A

= 0.8A

I

= 1.6A

F

I

= 1.2A

= 0.8A

F

I

= 0.4A

I

= 0.4A

F

−50

0

50

100

0

50

100

150

Junction temperature

T

(°C)

Junction temperature

T

(°C)

j

I

– V

V

– V

REG CC

CC

2.0

1.5

1.0

0.5

0

8.0

T =−40°C

T =25°C

T =135°C

j

T =−40°C

j

T =25°C

j

T =135°C

j

I

= 30 mA

REG

7.5

7.0

6.5

6.0

12

14

16

12

14

16

18

Control power supply voltage

V

(V)

Control power supply voltage

V

(V)

CC

13

2013-11-01

TPD4134K

t

– T

t – T

off j

on

j

3.0

2.0

1.0

0

3.0

2.0

1.0

0

V

= 280 V

= 15 V

V

= 280 V

= 15 V

BB

CC

BB

CC

I

= 1 A

I = 1 A

C

High-side

Low-side

High-side

Low-side

−50

0

50

100

150

−50

0

50

100

150

Junction temperature

T

(°C)

Junction temperature

T

(°C)

j

V

UV – T

V

UV – T

BS j

CC

j

12.5

12.0

10.5

10.0

9.5

V

UVD

UVR

V

UVD

UVR

CC

BS

11.5

11.0

10.5

9.0

8.5

10.0

−50

8.0

−50

0

50

100

150

0

50

100

150

Junction temperature

T

(°C)

Junction temperature

T

(°C)

j

V

– T

D – T

t j

R

j

1.0

0.8

0.6

0.4

0.2

0

6.0

V

= 15 V

CC

V

= 15 V

CC

4.0

2.0

0

−50

0

50

100

150

−50

0

50

100

150

Junction temperature

T

(°C)

Junction temperature

T

(°C)

j

14

2013-11-01

TPD4134K

I

– V

I

– V

BS (OFF) BS

BS (ON)

BS

500

400

300

200

100

500

400

300

200

100

T =−40°C

j

T =25°C

j

T =25°C

j

T =135°C

j

T =135°C

j

12

14

16

18

12

14

16

18

Bootstrap voltage V_BS(V)

Bootstrap voltage

V

(V)

BS

W

– T

j

W

– T

j

toff

ton

100

80

60

40

20

0

250

200

150

100

50

I

= 1.6A

= 1.2A

C

I

= 1.6A

= 1.2A

C

I

= 0.8A

= 0.4A

C

I

= 0.8A

= 0.4A

C

I

C

0

−50

0

50

100

150

0

50

100

150

Junction temperature

T

j

(°C)

Junction temperature

T

(°C)

j

15

2013-11-01

TPD4134K

Test Circuits

IGBT Saturation Voltage (U-phase low side)

1 A

VM

HU = 0V

HV = 0V

HW = 0V

LU = 5V

LV = 0V

LW = 0V

V_CC= 15V

FRD Forward Voltage (U-phase low side)

1 A

VM

16

2013-11-01

TPD4134K

V

CC

Current Dissipation

IM

V_CC= 15V

Regulator Voltage

30mA

VM

V_CC= 15V

17

2013-11-01

TPD4134K

Output ON/OFF Delay Time (U-phase low side)

IM

U = 280V

280Ω

2.2μF

HU = 0V

HV = 0V

HW = 0V

LU = PG

LV = 0V

LW = 0V

V_CC= 15V

90%

5V

10%

LU = PG

90%

10%

IM

t_on

t_off

18

2013-11-01

TPD4134K

VCC Under-voltage Protection Operating/Recovery Voltage (U-phase low side)

U = 18V

2kΩ

HU = 0V

HV = 0V

HW = 0V

LU = 5V

LV = 0V

LW = 0V

V_CC= 15V → 6V

VM

6V → 15V

*Note: Sweeps the V

pin voltage from 15 V and monitors the U pin voltage. The V

pin voltage when

CC

output is off defines the under-voltage protection operating voltage. Also sweeps from 6 V to

increase. The V

voltage.

pin voltage when output is on defines the under voltage protection recovery

CC

VBS Under-voltage Protection Operating/Recovery Voltage (U-phase high side)

V_BB= 18V

VM

BSU = 15V → 6V

6V → 15V

2kΩ

HU = 5V

HV = 0V

HW = 0V

LU = 0V

LV = 0V

LW = 0V

V

_CC= 15V

*Note: Sweeps the BSU pin voltage from 15 V to decrease and monitors the V

pin voltage. The BSU pin

BB

voltage when output is off defines the under voltage protection operating voltage. Also sweeps the

BSU pin voltage from 6V to increase and change the HU pin voltage at 5 V→0 V→5 V each time. It

repeats similarly output is on. When the BSU pin voltage when output is on defines the under

voltage protection recovery voltage.

19

2013-11-01

TPD4134K

Current Limit Operating Voltage (U-phase high side)

V_BB= 18V

15V

2kΩ

HU = 5V

HV = 0V

HW = 0V

LU = 0V

LV = 0V

LW = 0V

VM

V

_CC= 15V

IS/RS = 0V → 0.6V

*Note: Sweeps the IS/RS pin voltage and monitors the U pin voltage.

The IS/RS pin voltage when output is off defines the current control operating voltage.

Bootstrap Current Dissipation (U-phase high side)

IM

BSU = 15V

HU = 0V/5V

HV = 0V

HW = 0V

LU = 0V

LV = 0V

LW = 0V

V_CC= 15V

20

2013-11-01

TPD4134K

Turn-ON/OFF Loss (low side IGBT + high side FRD)

IM

V_BB/U = 280V

5mH

2.2μF

VM

L

HU = 0V

HV = 0V

HW = 0V

LU = PG

LV = 0V

LW = 0V

V

_CC= 15V

Input (LU = PG)

IGBT (C-E Voltage)

(U-GND)

Power Supply Current

W_toff

W_ton

21

2013-11-01

TPD4134K

Package Dimensions

HDIP26-P-1332-2.00

Unit: mm

Weight: 3.8 g (typ.)

22

2013-11-01

TPD4134K

RESTRICTIONS ON PRODUCT USE

•

Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information

in this document, and related hardware, software and systems (collectively "Product") without notice.

This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with

TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.

Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are

responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and

systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily

injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the

Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of

all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes

for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the

instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their

own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such

design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,

diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating

parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR

APPLICATIONS.

•

PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE

EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH

MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT

("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without

limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for

automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions,

safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE

PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your

TOSHIBA sales representative.

•

Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.

Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any

applicable laws or regulations.

•

The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any

infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to

any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.

ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE

FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY

WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR

LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND

LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO

SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.

•

Do not use or otherwise make available Product or related software or technology for any military purposes, including without

limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile

technology products (mass destruction weapons). Product and related software and technology may be controlled under the

applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the

U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited

except in compliance with all applicable export laws and regulations.

Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.

Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,

including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES

OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.

23

2013-11-01


型号：	TPD4134K
厂家：	TOSHIBA
描述：	IC BRUSHLESS DC MOTOR CONTROLLER, PDIP26, 32 X 13 MM, 2 MM PITCH, PLASTIC, HDIP-36, Motion Control Electronics 电动机控制光电二极管
文件：	总23页 (文件大小：365K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

TPD4134K [TOSHIBA]

相关型号：

TPD4135AK

TPD4135K

TPD4135K(Q)

TPD4136K

TPD4141K

TPD4142K

TPD4144AK

TPD4144K

TPD4146K

TPD480505D-3W

TPD480505SW-1W

TPD480512D-3W