TK11132MCL [TOKO]
VOLTAGE REGULATOR WITH ON/OFF SWITCH; 带ON / OFF开关稳压器
| 型号： | TK11132MCL |
| 厂家： | 
TOKO, INC |
| 描述： | VOLTAGE REGULATOR WITH ON/OFF SWITCH |
| 文件： | 总16页 (文件大小：89K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TK111xxM
VOLTAGE REGULATOR WITH ON/OFF SWITCH
FEATURES
APPLICATIONS
■ High Voltage Precision at ± 2.0% or ± 60 mV
■ Active High On/Off Control
■ Battery Powered Systems
■ Cellular Telephones
■ Pagers
■ Very Low Dropout Voltage (85 mV at 30 mA)
■ Very Low Noise
■ Personal Communications Equipment
■ Portable Instrumentation
■ Portable Consumer Equipment
■ Radio Control Systems
■ Toys
■ Miniature Package (SOT-23L-6)
■ Internal Thermal Shutdown
■ Short Circuit Protection
■ Excellent Ripple Rejection (70 dB @ 1 kHz)
■ Reverse Bias Protection
DESCRIPTION
TheTK111xxMisalowdropoutlinearregulatorwithabuilt-
in electronic switch. The internal switch can be controlled
byTTLorCMOSlogiclevels. Thedeviceisinthe“on”state
when the control pin is pulled to a logic high level. An
external capacitor can be connected to the noise bypass
pin to lower the output noise level to 30 µVrms.
TK111xxM
An internal PNP pass transistor is used to achieve a low
dropout voltage of 85 mV (typ.) at 30 mA load current. The
TK111xxM has a very low quiescent current of 140 µA
(typ.) at no load . The standby current is 100 nA maximum.
The internal thermal shutdown circuitry limits the junction
temperature to below 150 °C. The load current is internally
monitored and the device will shut down in the presence of
a short circuit or overcurrent condition at the output.
V
CONTROL
GND
IN
20P
GND
NOISE BYPASS
V
OUT
The TK111xxM is available in a miniature SOT-23L-6
surface mount package.
ORDERING INFORMATION
BLOCK DIAGRAM
TK111 M L
V
V
OUT
IN
Tape/Reel Code
Voltage Code
Temp Code
THERMAL
PROTECTION
Product Code
PACKAGE CODE
M: SOT-23L-6
VOLTAGE CODE
TAPE/REEL CODE
L: Tape Left
CONTROL
20 = 2.0 V
21 = 2.1 V
22 = 2.2 V
23 = 2.3 V
24 = 2.4 V
25 = 2.5 V
27 = 2.7 V
28 = 2.8 V
29 = 2.9 V
30 = 3.0 V
31 = 3.1 V
32 = 3.2 V
33 = 3.3 V
34 = 3.4 V
35 = 3.5 V
36 = 3.6 V
37 = 3.7 V
38 = 3.8 V
39 = 3.9 V
40 = 4.0 V
41 = 4.1 V
42 = 4.2 V
43 = 4.3 V
44 = 4.4 V
45 = 4.5 V
46 = 4.6 V
47 = 4.7 V
48 = 4.8 V
49 = 4.9 V
50 = 5.0 V
NOTE 1:
2.0 V to 2.3 V available
in C temperature code
(-30 to +80 °C) only.
TEMP. CODE:
C: -30 to +80 °C
I: -40 to +85 °C
BANDGAP
REFERENCE
GND
NOISE
BYPASS
March 1999 TOKO, Inc.
Page 1
TK111xxM
ABSOLUTE MAXIMUM RATINGS TK111xxMCL (VOUT ≥ 2.0 V)
Operating Temperature Range ...................-30 to +80 °C
Supply Voltage ......................................................... 16 V
Noise Bypass Terminal Voltage ................................. 5 V
Power Dissipation (Note 1) ................................ 600 mW
Reverse Bias............................................................ 10 V
Storage Temperature Range ................... -55 to +150 °C
Operating Voltage Range............................... 1.8 to 12 V
Junction Temperature ........................................... 150 °C
Lead Soldering Temperature (10 s) ...................... 235 °C
TK111xxMCL ELECTRICAL CHARACTERISTICS
Test conditions: VIN = VOUT(TYP) + 1 V, TA = 25 °C, unless otherwise specified.
SYMBOL
IQ
ISTBY
VOUT
PARAMETER
Quiescent Current
Standby Current
Output Voltage
TEST CONDITIONS
IOUT = 0 mA, Excluding ICONT
VIN = 6 V, Output OFF
MIN
TYP
MAX
200
0.1
UNITS
µA
140
µA
IOUT = 10 mA, VIN = VOUT(TYP) + 1 V
VIN = VOUT(TYP) + 1 V to
See Table 1
0.8
V
Line Reg Line Regulation
Load Reg Load Regulation
18
mV
V
OUT(TYP) + 6 V, (Note 2)
IOUT = 1 to 60 mA, (Note 2)
IOUT = 1 to 100 mA, (Note 2)
IOUT = 60 mA, (Note 2)
(Note 2)
8
30
55
mV
mV
mV
mA
14
VDROP
IOUT
Dropout Voltage
120
200
100
Continuous Output Current
5 ms pulse, 12.5 % duty cycle,
(Note 2)
IOUT(PULSE)
Pulse Output Current
130
mA
f = 1 kHz, CL = 4.7 µF,
CN = 0.1 µF, VIN = VOUT(TYP) + 2 V,
VR = 200 mVrms, IOUT = 10 mA,
(Notes 3,4)
RR
Ripple Rejection
70
30
dB
400 Hz ≤ f ≤ 80 kHz, CL = 4.7 µF,
CN = 0.01 µF, VIN = VOUT(TYP) + 2 V,
VNO
Output Noise Voltage
µVrms
IOUT = 10 mA, (Notes 3,4)
Noise Bypass Terminal
Voltage
Vref
1.25
25
V
∆VOUT /∆T
Temperature Coefficient
I
OUT = 10 mA
ppm/° C
CONTROL TERMINAL SPECIFICATIONS
ICONT
Control Current
VCONT = 1.8 V, Output ON
Output ON
1.2
4
µA
V
VCONT(ON)
Control Voltage ON
1.5
VCONT(OFF) Control Voltage OFF
Output OFF
0.35
V
Note 1: Power dissipation is 600 mW when mounted as recommended. Derate at 4.8 mW/°C for operation above 25 °C.
Note 2: Refer to “Definition of Terms.”
Note 3: Ripple rejection and noise voltage are affected by the value and characteristics of the capacitor used.
Note 4: Output noise voltage can be reduced by connecting a capacitor to the noise bypass terminal.
Gen. Note: Parameters with min. or max. values are 100% tested at TA = 25 °C.
Gen. Note: Exceeding the “Absolute Maximum Ratings” can damage the device.
Page 2
March 1999 TOKO, Inc.
TK111xxM
ABSOLUTE MAXIMUM RATINGS TK111xxMIL (VOUT ≥ 2.4 V)
Storage Temperature Range ................... -55 to +150 °C
Operating Temperature Range ...................-40 to +85 °C
Operating Voltage Range............................... 2.0 to 12 V
Junction Temperature ........................................... 150 °C
Lead Soldering Temperature (10 s) ...................... 235 °C
Supply Voltage ......................................................... 15 V
Control Terminal Voltage ......................................... 12 V
Noise Bypass Terminal Voltage ................................. 5 V
Power Dissipation (Note 1) ................................ 600 mW
Reverse Bias............................................................ 10 V
TK111xxMIL ELECTRICAL CHARACTERISTICS
Test conditions: VIN = VOUT(TYP) + 1 V, TA = -40 to +85 °C, unless otherwise specified.
SYMBOL
IQ
ISTBY
VOUT
PARAMETER
Quiescent Current
Standby Current
Output Voltage
TEST CONDITIONS
IOUT = 0 mA, Excluding ICONT
VIN = 6 V, Output OFF
MIN
TYP
MAX
200
0.2
UNITS
µA
140
µA
IOUT = 10 mA, VIN = VOUT(TYP) + 1 V
VIN = VOUT(TYP) + 1 V to
See Table 2
0.8
V
Line Reg Line Regulation
Load Reg Load Regulation
18
mV
V
OUT(TYP) + 6 V, (Note 2)
IOUT = 1 to 60 mA, (Note 2)
IOUT = 1 to 100 mA, (Note 2)
IOUT = 60 mA, (Note 2)
(Note 2)
8
30
55
mV
mV
mV
mA
14
VDROP
IOUT
Dropout Voltage
120
200
100
Continuous Output Current
5 ms pulse, 12.5 % duty cycle,
(Note 2)
IOUT(PULSE)
Pulse Output Current
130
mA
f = 1 kHz, CL = 4.7 µF,
CN = 0.1 µF, VIN = VOUT(TYP) + 2 V,
VR = 200 mVrms, IOUT = 10 mA,
(Notes 3,4)
RR
Ripple Rejection
70
30
dB
400 Hz ≤ f ≤ 80 kHz, CL = 4.7 µF,
CN = 0.01 µF, VIN = VOUT(TYP) + 2 V,
VNO
Output Noise Voltage
µVrms
IOUT = 10 mA, (Notes 3,4)
Noise Bypass Terminal
Voltage
Vref
1.25
25
V
∆VOUT /∆T
Temperature Coefficient
I
OUT = 10 mA
ppm/° C
CONTROL TERMINAL SPECIFICATIONS
ICONT
Control Current
VCONT = 1.8 V, Output ON
Output ON
1.2
6
µA
V
VCONT(ON)
Control Voltage ON
1.5
VCONT(OFF) Control Voltage OFF
Output OFF
0.35
V
Note 1: Power dissipation is 600 mW when mounted as recommended. Derate at 4.8 mW/°C for operation above 25 °C.
Note 2: Refer to “Definition of Terms.”
Note 3: Ripple rejection and noise voltage are affected by the value and characteristics of the capacitor used.
Note 4: Output noise voltage can be reduced by connecting a capacitor to the noise bypass terminal.
Gen. Note: Parameters with min. or max. values are 100% tested at TA = 25 °C.
Gen. Note: Exceeding the “Absolute Maximum Ratings” can damage the device.
March 1999 TOKO, Inc.
Page 3
TK111xxM
TK111xxMCL ELECTRICAL CHARACTERISTICS TABLE 1
Output
Voltage
Voltage
Code
VOUT(MIN)
VOUT(MAX)
Test
Voltage
Output
Voltage
Voltage
Code
VOUT(MIN)
VOUT(MAX)
Test
Voltage
2.0 V
2.1 V
2.2 V
2.3 V
2.4 V
2.5 V
2.7 V
2.8 V
2.9 V
3.0 V
3.1 V
3.2 V
3.3 V
3.4 V
3.5 V
20
21
22
23
24
25
27
28
29
30
31
32
33
34
35
1.940 V
2.040 V
2.140 V
2.240 V
2.340 V
2.440 V
2.640 V
2.740 V
2.840 V
2.940 V
3.038 V
3.136 V
3.234 V
3.332 V
3.430 V
2.060 V
2.160 V
2.260 V
2.360 V
2.460 V
2.560 V
2.760 V
2.860 V
2.960 V
3.060 V
3.162 V
3.264 V
3.366 V
3.468 V
3.570 V
3.0 V
3.1 V
3.2 V
3.3 V
3.4 V
3.5 V
3.7 V
3.8 V
3.9 V
4.0 V
4.1 V
4.2 V
4.3 V
4.4 V
4.5 V
3.6 V
3.7 V
3.8 V
3.9 V
4.0 V
4.1 V
4.2 V
4.3 V
4.4 V
4.5 V
4.6 V
4.7 V
4.8 V
4.9 V
5.0 V
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
3.528 V
3.626 V
3.724 V
3.822 V
3.920 V
4.018 V
4.116 V
4.214 V
4.312 V
4.410 V
4.508 V
4.606 V
4.704 V
4.802 V
4.900 V
3.672 V
3.774 V
3.876 V
3.978 V
4.080 V
4.182 V
4.284 V
4.386 V
4.488 V
7.590 V
4.692 V
4.794 V
4.896 V
4.998 V
5.100 V
4.6 V
4.7 V
4.8 V
4.9 V
5.0 V
5.1 V
5.2 V
5.3 V
5.4 V
5.5 V
5.6 V
5.7 V
5.8 V
5.9 V
6.0 V
Page 4
March 1999 TOKO, Inc.
TK111xxM
TK111xxMIL ELECTRICAL CHARACTERISTICS TABLE 2
Test Conditions: VIN = VOUT(TYP) + 1 V, IOUT = 30 mA, unless otherwise specified.
Room Temp. Range (TA = 25 °C)
Full Temp. Range (TA = -40 to +85 °C)
Output
Voltage
Voltage
Code
VOUT(MIN)
VOUT(MAX)
VOUT(MIN)
VOUT(MAX)
2.4 V
2.5 V
2.7 V
2.8 V
2.9 V
3.0 V
3.1 V
3.2 V
3.3 V
3.4 V
3.5 V
3.6 V
3.7 V
3.8 V
3.9 V
4.0 V
4.1 V
4.2 V
4.3 V
4.4 V
4.5 V
4.6 V
4.7 V
4.8 V
4.9 V
5.0 V
24
25
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
2.340 V
2.440 V
2.640 V
2.740 V
2.840 V
2.940 V
3.038 V
3.136 V
3.234 V
3.332 V
3.430 V
3.528 V
3.626 V
3.724 V
3.822 V
3.920 V
4.018 V
4.116 V
4.214 V
4.312 V
4.410 V
4.598 V
4.696 V
4.794 V
4.892 V
4.900 V
2.460 V
2.560 V
2.760 V
2.860 V
2.960 V
3.060 V
3.162 V
3.264 V
3.366 V
3.468 V
3.570 V
3.672 V
3.774 V
3.876 V
3.988 V
4.080 V
4.182 V
4.284 V
4.366 V
4.488 V
4.590 V
4.692 V
4.794 V
4.896 V
4.998 V
5.100 V
2.305 V
2.405 V
2.605 V
2.705 V
2.805 V
2.905 V
3.007 V
3.104 V
3.201 V
3.298 V
3.395 V
3.492 V
3.589 V
3.686 V
3.783 V
3.880 V
3.977 V
4.074 V
4.171 V
4.268 V
4.365 V
4.462 V
4.559 V
4.656 V
4.753 V
4.850 V
2.495 V
2.595 V
2.795 V
2.895 V
2.995 V
3.095 V
3.193 V
3.296 V
3.400 V
3.502 V
3.605 V
3.708 V
3.811 V
3.914 V
4.017 V
4.120 V
4.223 V
4.326 V
4.429 V
4.532 V
4.635 V
4.738 V
4.841 V
4.944 V
5.047 V
5.150 V
March 1999 TOKO, Inc.
Page 5
TK111xxM
TEST CIRCUIT
V
IN
V
V
OUT
IN
I
IN
C
L
C
IN
1 µF
I
OUT
2.2 µF
TANTALUM
CONT
NOISE BYPASS
C
= 0.0047 µF
N
I
CONT
V
CONT
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25 °C, unless otherwise specified.
OUTPUT VOLTAGE VS.
INPUT VOLTAGE
LOAD REGULATION
SHORT CIRCUIT CURRENT
V
TYPICAL
OUT
5
4
3
2
I
= 0 mA
OUT
V
TYPICAL
OUT
I
= 30 mA
OUT
I
= 60 mA
OUT
I
= 90 mA
OUT
1
0
0
50
100
0
150
300
0
V
= V
OUT
IN
(V) (50 mV/ DIV)
I
(mA)
I
(mA)
V
IN
OUT
OUT
DROPOUT VOLTAGE VS.
OUTPUT CURRENT
GROUND CURRENT VS.
OUTPUT CURRENT
LINE REGULATION
0
-100
-200
10
8
V
TYPICAL
OUT
6
4
-300
-400
-500
2
0
0
10
20
0
100
200
0
75
150
V
(V)
I
(mA)
I
(mA)
IN
OUT
OUT
Page 6
March 1999 TOKO, Inc.
TK111xxM
TYPICAL PERFORMANCE CHARACTERISTICS (CONT.)
TA = 25 °C, unless otherwise specified.
REVERSE BIAS CURRENT
STANDBY CURRENT (OFF MODE)
VS. INPUT VOLTAGE
QUIESCENT CURRENT (ON MODE)
VS. INPUT VOLTAGE
(V = 0 V)
IN
I
= 0 mA
OUT
500
400
300
200
100
2
V
= 3 V
OUT
50
0
1
100
0
0
0
10
20
0
10
(V)
20
0
5
10
V
(V)
V
V
(V)
IN
REV
IN
CONTROL CURRENT VS.
CONTROL VOLTAGE
GROUND CURRENT
DROPOUT VOLTAGE
2
10
V
OUT
I
= 60 mA
OUT
8
6
4
2
0
200
I
= 100 mA
OUT
1
0
I
= 60 mA
= 30 mA
OUT
OUT
50
I
= 30 mA
OUT
100
0
I
0
1
2
3
4
5
-50
0
50
100
-50
0
100
V
(V)
T
A
(°C)
T (°C)
A
CONT
CONTROL CURRENT
V
(V
, ON POINT)
= 0 Ω
MAXIMUM OUTPUT CURRENT
= 2.7 V
CONT OUT
V
R
2
OUT
10
CONT
OR ABOVE
260
250
240
230
220
V
= 5 V
CONT
8
6
1
4
V
= 1.8 V
CONT
2
0
0
-50
0
50
100
-50
0
50
100
-50
0
50
100
T
A
(°C)
T
A
(°C)
T (°C)
A
March 1999 TOKO, Inc.
Page 7
TK111xxM
TYPICAL PERFORMANCE CHARACTERISTICS (CONT.)
TA = 25 °C, unless otherwise specified.
RIPPLE REJECTION
OUTPUT VOLTAGE VARIATION
OUTPUT NOISE LEVEL VS. C
N
0
-20
20
250
200
150
100
50
I
= 60 mA
I
= 30 mA
OUT
OUT
10
0
C
= 2.2 µF, C = .01 µF
N
L
C
= 2.2 µF
L
2.8 V
-40
C
= 4.7 µF, C = 0.1 µF
N
L
C
= 3.3µF
L
3.0 V
-60
-10
C
= 10 µF
L
-80
-20
-30
C
= 4.7 µF, C = 1.0 µF
N
L
-100
0
0.01
1
10
100
-50
0
50
100
1 pF 10
100 1000
0.1 µF .1
f (kHz)
T
A
(°C)
C
N
LOAD CURRENT STEP RESPONSE 1
LINE VOLTAGE STEP RESPONSE
V +2 V
NOISE SPECTRUM
0
C
C
= 2.2 µF
= 0.01 µF
OUT
100 mA
1 OR 5 mA
1 TO 100 mA
L
N
V
+1 V
OUT
C
= 0.001 µF
-50
N
C
= 3.3 µF, C = NONE
N
L
C
= 3.3 µF, C = 0.1 µF
N
L
C
= 0.01 µF
N
5 TO 100 mA
SPECTRUM ANALYZER BACK-
GROUND NOISE
-100
0
200
400
600 800
0
100
200 300
400
0
500 k
f (Hz)
1 M
TIME (µs)
TIME (µs)
LOAD CURRENT STEP RESPONSE 2
50 mA = 0.01 µF
C
N
0 mA
C
= 4.7 µF
L
C
= 2.2 µF
L
C
= 10 µF
= 47 µF
L
C
L
0
2
4
6
8
TIME (ms)
Page 8
March 1999 TOKO, Inc.
TK111xxM
DEFINITION AND EXPLANATION OF TECHNICAL TERMS
thegroundterminalundernoloadconditions(IOUT =0mA).
OUTPUT VOLTAGE (VOUT
)
GROUND CURRENT
The output voltage is specified with VIN = (VOUT(TYP) + 1 V)
and IOUT = 10 mA.
Ground current is the current which flows through the
ground pin(s). It is defined as IIN - IOUT, excluding control
current.
DROPOUT VOLTAGE (VDROP
)
The dropout voltage is the difference between the input
voltage and the output voltage at which point the regulator
starts to fall out of regulation. Below this value, the output
voltage will fall as the input voltage is reduced. It is
dependent upon the load current and the junction
temperature.
RIPPLE REJECTION RATIO (RR)
Ripple rejection is the ability of the regulator to attenuate
the ripple content of the input voltage at the output. It is
specified with 200 mVrms, 1 kHz superimposed on the
inputvoltage,whereVIN =VOUT+2V.Theoutputdecoupling
capacitor is set to 4.7 µF, the noise bypass capacitor is set
to 0.01 µF, 0.1 µF, 1.0 µF and the load current is set to
10 mA. Ripple rejection is the ratio of the ripple content of
the output vs. the input and is expressed in dB.
OUTPUT CURRENT (IOUT(MAX)
)
The rated output current is specified under the condition
where the output voltage drops 0.3 V below the value
specified with IOUT = 10 mA. The input voltage is set to
VOUT +1V,andthecurrentispulsedtominimizetemperature
effect.
Example: 64 dB at CN = 0.01 µF, 70 dB at
CN = 0.1 µF, 74 dB at CN = 1.0 µF
CONTINUOUS OUTPUT CURRENT (IOUT
)
SENSOR CIRCUITS
Overcurrent Sensor
Normal operating output current. This is limited by the
package power dissipation.
The overcurrent sensor protects the device if the output is
shorted to ground.
PULSE OUTPUT CURRENT (IOUT (PULSE)
)
Max pulse width 5 ms, Duty cycle 12.5%: pulse load only.
Thermal Sensor
LINE REGULATION (Line Reg)
The thermal sensor protects the device if the junction
temperature exceeds the safe value (Tj = 150 °C). This
temperaturerisecanbecausedbyextremeheat,excessive
power dissipation caused by large output voltage drops, or
excessive output current. The regulator will shut off when
the temperature exceeds the safe value. As the junction
temperature decreases, the regulator will begin to operate
again. Under sustained fault conditions, the regulator
output will oscillate as the device turns off then resets.
Damage may occur to the device under extreme fault
conditions.
Line regulation is the ability of the regulator to maintain a
constant output voltage as the input voltage changes. The
line regulation is specified as the input voltage is changed
from VIN = VOUT(TYP) + 1 V to VIN = VOUT(TYP) + 6 V.
LOAD REGULATION (Load Reg)
Load regulation is the ability of the regulator to maintain a
constant output voltage as the load current changes. It is
a pulsed measurement to minimize temperature effects
with the input voltage set to VIN = VOUT(TYP) +1 V. The load
regulation is specified under two output current step
conditions of 1 mA to 60 mA and 1 mA to 100 mA.
Reverse Voltage Protection
Reverse voltage protection prevents damage due to the
output voltage being higher than the input voltage. This
faultconditioncanoccurwhentheoutputcapacitorremains
charged and the input is reduced to zero, or when an
QUIESCENT CURRENT (IQ)
The quiescent current is the current which flows through
March 1999 TOKO, Inc.
Page 9
TK111xxM
DEFINITION AND EXPLANATION OF TECHNICAL TERMS (CONT.)
external voltage higher than the input voltage is applied to
the output side.
ON/OFF RESPONSE WITH CONTROL
The turn-on time depends upon the value of the output
capacitorandthenoisebypasscapacitor.Theturn-ontime
will increase with the value of either capacitor. The graphs
below show the relationship between turn-on time and
loadcapacitance.Ifthevalueofthesecapacitorsisreduced,
theloadandlineregulationwillsufferandthenoisevoltage
will increase. If the value of these capacitors is increased,
the turn on time will increase.
REDUCTION OF OUTPUT NOISE
AlthoughthearchitectureoftheTokoregulatorsisdesigned
to minimize semiconductor noise, further reduction can be
achieved by the selection of external components. The
obvious solution is to increase the size of the output
capacitor. A more effective solution would be to add a
capacitor to the noise bypass terminal. The value of this
capacitorshouldbe0.1µForhigher(highervaluesprovide
greater noise reduction). Although stable operation is
possible without the noise bypass capacitor, this terminal
has a high impedance and care should be taken to avoid
a large circuit area on the printed circuit board when the
capacitorisnotused. Pleasenotethatseveralparameters
are affected by the value of the capacitors and bench
testing is recommended when deviating from standard
values.
OUTPUT VOLTAGE RESPONSE B
(OFF→ON)
I
= 30 mA, C = 2.2 µF
L
LOAD
C
= 0.1 µF
N
C
= 0.33 µF
N
C
= 0.47 µF
N
C
= 0.68µF
N
C
= 1.0 µF
CONTROL FUNCTION
N
The TK111xxM has an active high control pin. The control
pin requires over 1.8 V for operation and under 0.6 V for
standby. For the range of 0.6 V < VCONT < 1.8 V, operation
is undefined. If the control function is not used, connect the
control pin to VIN.
0
2
4
6
8
TIME (ms)
OUTPUT VOLTAGE RESPONSE A
(OFF→ON)
V
IN
I
= 30 mA, C = 3300 pF
N
LOAD
C
= 0.68 µF
L
SW
C
= 0.47µF
L
C
= 1.5 µF
L
C
= 1.0 µF
L
C
N
-5
5
15
25
35
45
TIME (µs)
CONTROL FUNCTION
Page 10
March 1999 TOKO, Inc.
TK111xxM
DEFINITION AND EXPLANATION OF TECHNICAL TERMS (CONT.)
The range of usable currents can also be found from the
graph below.
PACKAGE POWER DISSIPATION (PD)
This is the power dissipation level at which the thermal
sensor is activated. The IC contains an internal thermal
sensorwhichmonitorsthejunctiontemperature. Whenthe
junction temperature exceeds the monitor threshold of
150 °C, the IC is shut down. The junction temperature
rises as the difference between the input power (VIN x IIN)
and the output power (VOUT x IOUT) increases. The rate of
temperature rise is greatly affected by the mounting pad
configuration on the PCB, the board material, and the
ambient temperature. When the IC mounting has good
thermal conductivity, the junction temperature will be low
even if the power dissipation is great. When mounted on
the recommended mounting pad, the power dissipation of
the SOT-23L-6 is increased to 600 mW. For operation at
ambient temperatures over 25 °C, the power dissipation of
theSOT-23L-6deviceshouldbederatedat4.8mW/°C. To
determine the power dissipation for shutdown when
mounted, attach the device on the actual PCB and
deliberately increase the output current (or raise the input
voltage) until the thermal protection circuit is activated.
Calculatethepowerdissipationofthedevicebysubtracting
the output power from the input power. These
measurements should allow for the ambient temperature
ofthePCB. ThevalueobtainedfromPD /(150 °C-TA)isthe
derating factor. The PCB mounting pad should provide
maximum thermal conductivity in order to maintain low
device temperatures. As a general rule, the lower the
temperature, the better the reliability of the device. The
thermalresistancewhenmountedisexpressedasfollows:
(mW)
3
P
D
6
D
PD
4
5
25
50
75
( C)
150
T
A
Procedure:
1) Find PD
2) PD1 is taken to be PD x (~ 0.8 - 0.9)
3) Plot PD1 against 25 °C
4) Connect PD1 to the point corresponding to the 150 °C
with a straight line.
5) In design, take a vertical line from the maximum
operating temperature (e.g., 75 °C) to the derating
curve.
6) Read off the value of PD against the point at which the
vertical line intersects the derating curve. This is taken
as the maximum power dissipation, DPD
.
1.0
MOUNTED AS
0.8
SHOWN
Tj = 0jA x PD + TA
0.6
FREE AIR
For Toko ICs, the internal limit for junction temperature is
150 °C. If the ambient temperature (TA ) is 25 °C, then:
0.4
0.2
0
150 °C = 0jA x PD + 25 °C
0jA = 125 °C/ PD
0
50
100
150
T
(°C)
A
PD is the value when the thermal sensor is activated. A
simple way to determine PD is to calculate VIN x IIN when
the output side is shorted. Input current gradually falls as
temperature rises. You should use the value when thermal
equilibrium is reached.
SOT-23L-6 POWER DISSIPATION CURVE
March 1999 TOKO, Inc.
Page 11
TK111xxM
APPLICATION INFORMATION
INPUT-OUTPUT CAPACITORS
Linearregulatorsrequireanoutputcapacitorinordertomaintainregulatorloopstability.Thiscapacitorshouldbeselected
to ensure stable operation over the desired temperature and load range. The graphs below show the effects of
capacitance value and Equivalent Series Resistance (ESR) on the stable operation area.
111xx
C
L
ESR
C = 1 µF
C = 2.2 µF
C = 3.3 µF
C = 10 µF
L
L
L
L
1000
100
1000
100
1000
100
1000
100
10
10
10
10
STABLE
OPERATION
AREA
STABLE
OPERATION
AREA
STABLE
OPERATION
AREA
STABLE
OPERATION
AREA
1
1
1
1
0.1
0.1
0.1
0.1
0 .01
0 .01
0 .01
0 .01
130
130
130
130
1
50
I
100
1
50
I
100
1
50
I
100
1
50
I
100
(mA)
(mA)
OUT
(mA)
(mA)
OUT
OUT
OUT
In general, the capacitor should be at least 1 µF (aluminum electrolytic) and be rated for the actual ambient operating
temperature range. The table below shows typical characteristics for several types and values of capacitance. Please
note that the ESR varies widely depending upon manufacturer, type, size, and material.
ESR
Capacitance
Aluminum
Capacitor
Tantalum
Capacitor
Ceramic
Capacitor
1.0 µF
2.2 µF
3.3 µF
10 µF
2.4 Ω
2.0 Ω
4.6 Ω
1.4 Ω
2.3 Ω
1.9 Ω
1.0 Ω
0.5 Ω
0.140 Ω
0.059 Ω
0.049 Ω
0.025 Ω
Note: ESR is measured at 10 kHz.
Page 12
March 1999 TOKO, Inc.
TK111xxM
APPLICATION INFORMATION (CONT.)
BOARD LAYOUT
Copper pattern should be as large as possible. Power dissipation is 600 mW for the SOT-23L-6. A low ESR capacitor
is recommended. For low temperature operation, select a capacitor with a low ESR at the lowest operating temperature
to prevent oscillation, degradation of ripple rejection and increase in noise. The minimum recommended capacitance is
1.0 µF.
GND
V
V
OUT
IN
+
+
CONTROL
NOISE BYPASS
SOT-23L-6 BOARD LAYOUT
March 1999 TOKO, Inc.
Page 13
TK111xxM
NOTES
Page 14
March 1999 TOKO, Inc.
TK111xxM
NOTES
March 1999 TOKO, Inc.
Page 15
TK111xxM
PACKAGE OUTLINE
Marking Information
SOT-23L-6
Product Code
TK111xxM
W
+0.15
0.4- 0.05
Voltage Code
0.1
M
0.6
TK11120M
TK11121M
TK11122M
TK11123M
TK11124M
TK11125M
TK11127M
TK11128M
TK11129M
TK11130M
TK11131M
TK11132M
TK11133M
TK11134M
TK11135M
TK11136M
TK11137M
TK11138M
TK11139M
TK11140M
TK11141M
TK11142M
TK11143M
TK11144M
TK11145M
TK11146M
TK11147M
TK11148M
TK11149M
TK11150M
20
21
22
23
24
25
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
6
5
4
Marking
Product Code
Voltage Code
+0.15
1
2
3
0.32- 0.05
e
e
0.95
0.1
0.95
M
5 PL
e
e
0.95
0.95
Recommended Mount Pad
+0.3
- 0.1
3.5
(3.4)
2.2
0.4
+ 0.3
3.3
Dimensions are shown in millimeters
Tolerance: x.x = ± 0.2 mm (unless otherwise specified)
Toko America, Inc. Headquarters
1250 Feehanville Drive, Mount Prospect, Illinois 60056
Tel: (847) 297-0070 Fax: (847) 699-7864
TOKO AMERICA REGIONAL OFFICES
Midwest Regional Office
Toko America, Inc.
1250 Feehanville Drive
Mount Prospect, IL 60056
Tel: (847) 297-0070
Western Regional Office
Toko America, Inc.
2480 North First Street , Suite 260
San Jose, CA 95131
Tel: (408) 432-8281
Fax: (408) 943-9790
Eastern Regional Office
Toko America, Inc.
107 Mill Plain Road
Danbury, CT 06811
Tel: (203) 748-6871
Fax: (203) 797-1223
Semiconductor Technical Support
Toko Design Center
4755 Forge Road
Colorado Springs, CO 80907
Tel: (719) 528-2200
Fax: (719) 528-2375
Fax: (847) 699-7864
Visit our Internet site at http://www.tokoam.com
The information furnished by TOKO, Inc. is believed to be accurate and reliable. However, TOKO reserves the right to make changes or improvements in the design, specification or manufacture of its
products without further notice. TOKO does not assume any liability arising from the application or use of any product or circuit described herein, nor for any infringements of patents or other rights of
third parties which may result from the use of its products. No license is granted by implication or otherwise under any patent or patent rights of TOKO, Inc.
Page 16
March 1999 TOKO, Inc.
© 1999 Toko, Inc.
IC-xxx-TK111M
0798O0.0K
Printed in the USA
All Rights Reserved
相关型号：
TK11132MCLN
Fixed Positive LDO Regulator, 3.2V, 0.2V Dropout, PDSO6, SOT-23, 6 PINWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11132MI
Fixed Positive LDO Regulator, 3.2V, 0.2V Dropout, PDSO6, MINIATURE, SOT-23, 6 PINWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11132MIL
VOLTAGE REGULATOR WITH ON/OFF SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11132MILN
Fixed Positive LDO Regulator, 3.2V, 0.2V Dropout, PDSO6, SOT-23, 6 PINWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11132S
VOLTAGE REGULATOR WITH ON/OFF SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11132SC
暂无描述Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11132SCL
VOLTAGE REGULATOR WITH ON/OFF SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11132SCLN
Fixed Positive LDO Regulator, 3.2V, 0.2V Dropout, PDSO5, SOT-23, 5 PINWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11132SI
暂无描述Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11132SIL
VOLTAGE REGULATOR WITH ON/OFF SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11133CSCL
Fixed Positive LDO Regulator, 3.3V, 0.35V Dropout, PDSO5, PLASTIC, SOT-23, 5 PINWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
TK11133CSCL-G
Fixed Positive LDO Regulator, 3.3V, 0.14V Dropout, PDSO5, LEAD FREE, SOT-23, 5 PINWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TOKO
©2020 ICPDF网 联系我们和版权申明