UCC27288DR [TI]
UCC27288 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and External Bootstrap Diode;型号: | UCC27288DR |
厂家: | TEXAS INSTRUMENTS |
描述: | UCC27288 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and External Bootstrap Diode |
文件: | 总32页 (文件大小:1537K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
UCC27288 2.5-A/3.5-A 120-V Half-Bridge Driver
with 8-V UVLO and External Bootstrap Diode
1 Features
3 Description
•
Drives two N-channel MOSFETs in high-side low-
The UCC27288 is a robust N-channel MOSFET driver
side configuration
with a maximum switch node (HS) voltage rating of
100 V. It allows for two N-channel MOSFETs to be
controlled in half-bridge or synchronous buck
configuration based topologies. Its 3.5-A peak sink
current and 2.5-A peak source current along with low
pull-up and pull-down resistance allows the
UCC27288 to drive large power MOSFETs with
minimum switching losses during the transition of the
MOSFET Miller plateau. Since the inputs are
independent of the supply voltage, UCC27288 can be
used in conjunction with both analog and digital
controllers. Two inputs are completely independent of
each other and therefore provides added control
design flexibility.
•
•
•
•
•
•
16-ns typical propagation delay
12-ns rise, 10-ns typical fall time with 1800-pF load
1-ns typical delay matching
Configurable external bootstrap diode
8-V typical undervoltage lockout
Absolute maximum negative voltage handling on
inputs (–5 V)
•
Absolute maximum negative voltage handling on
HS (–14 V)
•
•
•
•
•
3.5-A sink, 2.5-A Source output currents
Absolute maximum boot voltage 120 V
Inputs are independent of each other and VDD
Under voltage lockout for both channels
Specified from –40°C to 140°C junction
temperature
The input pins as well as the HS pin are able to
tolerate significant negative voltage, which improves
system robustness. The inputs are completely
independent of each other. This allows for control
flexibility where two outputs can be overlapped by
overlapping inputs if needed. Small propagation delay
and delay matching specifications minimize the dead-
time requirement which improves system efficiency.
2 Applications
•
•
•
•
•
Solar power optimizer
Merchant network & server PSU
Merchant telecom rectifiers
DC input BLDC motor drive
Test & measurement equipment
Under voltage lockout (UVLO) is provided for both the
high-side and low-side driver stages forcing the
outputs low if the VDD voltage is below the specified
threshold. No integrated bootstrap diode allows user
to use application-appropriate external bootstrap
diode. UCC27288 is offered in an SOIC8 package to
improve system robustness in harsh environments.
10V
75V
DBoot
VDD
HO
Device Information
PART NUMBER
PACKAGE (SIZE)(1)
HI
HB
To Load
UCC27288
SOIC8 (6 mm x 5mm)
LI
HS
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
VSS
LO
Simplified Application Diagram
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
Table of Contents
1 Features............................................................................1
2 Applications.....................................................................1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings........................................ 4
6.2 ESD Ratings............................................................... 4
6.3 Recommended Operating Conditions.........................4
6.4 Thermal Information....................................................5
6.5 Electrical Characteristics.............................................5
6.6 Switching Characteristics............................................6
6.7 Typical Characteristics................................................7
7 Detailed Description......................................................11
7.1 Overview................................................................... 11
7.2 Functional Block Diagram......................................... 11
7.3 Feature Description...................................................12
7.4 Device Functional Modes..........................................13
8 Application and Implementation..................................15
8.1 Application Information............................................. 15
8.2 Typical Application.................................................... 16
9 Power Supply Recommendations................................24
10 Layout...........................................................................25
10.1 Layout Guidelines................................................... 25
10.2 Layout Example...................................................... 25
11 Device and Documentation Support..........................26
11.1 Receiving Notification of Documentation Updates..26
11.2 Support Resources................................................. 26
11.3 Trademarks............................................................. 26
11.4 Electrostatic Discharge Caution..............................26
11.5 Glossary..................................................................26
12 Mechanical, Packaging, and Orderable
Information.................................................................... 26
4 Revision History
Changes from Revision * (June 2020) to Revision A (October 2020)
Page
•
Changed marketing status from Advance Information to initial release. ............................................................1
Copyright © 2020 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
5 Pin Configuration and Functions
VDD
HB
1
2
3
4
8
7
6
5
LO
VSS
LI
HO
HS
HI
Not to scale
Figure 5-1. D Package 8-Pin SOIC Top View
Pin Functions
PIN
I/O(1)
DESCRIPTION
Name
D
High-side bootstrap supply. The external bootstrap diode and the external bootstrap capacitor is required to
generate bootstrap supply from VDD. Connect positive side of the bootstrap capacitor and cathode of an
external diode to this pin. The external diode should be 100V (minimum) rated. Higher voltage rated diode is
acceptable too. Typical recommended value of HB bypass capacitor is 0.1 μF, This value primarily depends
on the gate charge of the high-side MOSFET.
HB
2
P
HI
5
3
I
High-side input.
High-side output. Connect to the gate of the high-side power MOSFET or one end of external gate resistor,
when used.
HO
O
High-side source connection. Connect to source of high-side power MOSFET. Connect negative side of
bootstrap capacitor to this pin.
HS
LI
4
6
8
P
I
Low-side input
Low-side output. Connect to the gate of the low-side power MOSFET or one end of external gate resistor,
when used.
LO
O
Positive supply to the low-side gate driver. Decouple this pin to VSS. Typical decoupling capacitor value is 1
μF. When using an external boot diode, connect the anode to this pin. If series resistor is used in series with
the boot diode then connect one end of series boot resistor to this pin and other end of the resistor should
be connected to the anode of the external boot diode.
VDD
VSS
1
7
P
G
Negative supply terminal for the device which is generally the system ground.
(1) P = Power, G = Ground, I = Input, O = Output, I/O = Input/Output
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
(1) (2)
All voltages are with respect to Vss
MIN
–0.3
–5
MAX
20
UNIT
V
VDD
Supply voltage
VHI, VLI
Input voltages on HI and LI
20
V
DC
–0.3
–2
VDD + 0.3
VDD + 0.3
VHB + 0.3
VHB + 0.3
100
VLO
VHO
VHS
Output voltage on LO
Output voltage on HO
Voltage on HS
V
V
V
Pulses < 100 ns(3)
DC
VHS – 0.3
VHS – 2
–10
Pulses < 100 ns(3)
DC
Pulses < 100 ns(3)
–14
100
VHB
Voltage on HB
–0.3
–0.3
–40
120
V
VHB-HS
TJ
Voltage on HB with respect to HS
Operating junction temperature
Lead temperature (soldering, 10 sec.)
Storage temperature
20
V
150
°C
°C
°C
300
Tstg
–65
150
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
(2) All voltages are with respect to Vss. Currents are positive into, negative out of the specified terminal.
(3) Values are verified by characterization only.
6.2 ESD Ratings
VALUE
±2000
±1500
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) (2)
V(ESD)
Electrostatic discharge
V
Charged-device model (CDM), per JEDEC specification JESD22-C101(3)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) Pins HS, HB and HO are rated at 500V HBM
(3) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
8
NOM
MAX
16
UNIT
VDD
Supply voltage
12
V
VHI, VLI
VLO
Input Voltage
0
VDD
VDD
VHB
100
Low side output voltage
High side output voltage
Voltage on HS(1)
0
VHO
VHS
–8
VHS
V
Voltage on HS (Pulses < 100 ns)(1)
–12
VHS + 8
100
VHB
Vsr
TJ
Voltage on HB
VHS+16
50
V
Voltage slew rate on HS
Operating junction temperature
V/ns
°C
–40
140
(1) VHB-HS < 16V (Voltage on HB with respect to HS must be less than 16V)
Copyright © 2020 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
6.4 Thermal Information
UCC27288
THERMAL METRIC(1)
D
8 PINS
118.3
53.6
63.1
10.7
62.1
n/a
UNIT
RθJA
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top) Junction-to-case (top) thermal resistance
RθJB
ψJT
Junction-to-board thermal resistance
Junction-to-top characterization parameter
Junction-to-board characterization parameter
ψJB
RθJC(bot) Junction-to-case (bottom) thermal resistance
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.5 Electrical Characteristics
VDD = VHB = 12 V, VHS = VSS = 0 V, No load on LO or HO, TJ = –40°C to +140°C, (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP MAX UNIT
SUPPLY CURRENTS
IDD
VDD quiescent current
VDD operating current
HB quiescent current
VLI = VHI = 0
0.36 0.45 mA
IDDO
IHB
f = 500 kHz, CLOAD = 0
VLI = VHI = 0 V
2.2
0.2
2.5
2.0
0.1
4.5
0.4
4
mA
mA
mA
μA
IHBO
IHBS
IHBSO
INPUT
VHIT
VLIT
HB operating current
f = 500 kHz, CLOAD = 0
VHS = VHB = 110 V
f = 500 kHz, CLOAD = 0
HB to VSS quiescent current
HB to VSS operating current(1)
50
mA
Input rising threshold (HI and LI)
Input falling threshold (HI and LI)
Input voltage Hysteresis (HI and LI)
Input pulldown resistance (HI and LI)
1.9
0.9
2.1
1.1
1.0
250
2.4
1.3
V
V
VIHYS
RIN
V
100
350
kΩ
UNDERVOLTAGE LOCKOUT PROTECTION (UVLO)
VDDR
VDD rising threshold
6.5
5.7
7.0
6.5
0.5
6.3
5.8
0.5
7.8
7.3
V
V
V
V
V
V
VDDF
VDD falling threshold
VDDHYS
VHBR
VDD threshold hysteresis
HB rising threshold with respect to HS pin
HB falling threshold with respect to HS pin
HB threshold hysteresis
5.5
5.0
7.1
6.6
VHBF
VHBHYS
LO GATE DRIVER
VLOL
VLOH
Low level output voltage
ILO = 100 mA
0.085 0.4
0.13 0.42
2.5
V
V
A
A
High level output voltage
Peak pullup current (1)
Peak pulldown current (1)
ILO = -100 mA, VLOH = VDD – VLO
VLO = 0 V
VLO = 12 V
3.5
HO GATE DRIVER
VHOL
VHOH
Low level output voltage
IHO = 100 mA
0.1
0.4
V
V
A
A
High level output voltage
Peak pullup current (1)
Peak pulldown current (1)
IHO = –100 mA, VHOH = VHB- VHO
VHO = 0 V
0.13 0.42
2.5
3.5
VHO = 12 V
(1) Parameter not tested in production
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
6.6 Switching Characteristics
VDD = VHB = 12 V, VHS = VSS = 0 V, No load on LO or HO, TJ = –40°C to +140°C, (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
PROPAGATION DELAYS
tDLFF
tDHFF
tDLRR
tDHRR
VLI falling to VLO falling
VHI falling to VHO falling
VLI rising to VLO rising
VHI rising to VHO rising
See Figure 6-1
16
16
16
16
30
30
30
30
ns
ns
ns
ns
See Figure 6-1
See Figure 6-1
See Figure 6-1
DELAY MATCHING
tMON
From LO being ON to HO being OFF
From LO being OFF to HO being ON
See Figure 6-1
See Figure 6-1
1
1
7
7
ns
ns
tMOFF
OUTPUT RISE AND FALL TIME
tR
tF
tR
tF
LO, HO rise time
CLOAD = 1800 pF, 10% to 90%
CLOAD = 1800 pF, 90% to 10%
CLOAD = 0.1 μF, 30% to 70%
CLOAD = 0.1 μF, 70% to 30%
12
10
ns
ns
μs
μs
LO, HO fall time
LO, HO (3 V to 9 V) rise time
LO, HO (3 V to 9 V) fall time
0.33
0.23
0.6
0.6
MISCELLANEOUS
TPW,min Minimum input pulse width that changes the output
20
ns
LI
HI
Input
(HI, LI)
LO
TDLRR, TDHRR
Output
(HO, LO)
HO
TDLFF
,
TDHFF
Time (s)
Time (s)
TMOFF
TMON
Figure 6-1. Timing Diagram
Copyright © 2020 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
6.7 Typical Characteristics
Unless otherwise specified VVDD=VHB = 12 V, VHS=VVSS = 0 V, No load on outputs
0.3
0.275
0.25
0.225
0.2
0.22
0.18
0.14
0.1
0.175
0.15
0.125
0.1
0.06
0.02
8V
12V
16V
8V
12V
16V
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
IDDQ
IHBQ
VHI = VLI = 0 V
VHI = VLI = 0 V
Figure 6-2. VDD Quiescent Current
Figure 6-3. HB Quiescent Current
6
5
4
3
2
1
0
4.5
4
-40°C
25°°C
140°°C
-40°C
25°C
140°C
3.5
3
2.5
2
1.5
1
0.5
0
1
2
3 4 5 67 10
20 30 50 70100 200
Frequency (kHz)
500 1000
1
2
3 4 567 10
20 30 50 70100 200
Frequency (kHz)
500 1000
IDDO
IHBO
CL = 0 F
VDD =VHB= 12V
CL = 0 F
VDD =VHB= 12V
Figure 6-4. VDD Operating Current
Figure 6-5. HB Operating Current
20
18
16
14
12
10
8
2.22
2.21
2.2
2.19
2.18
2.17
2.16
6
4
8V
12V
16V
2
0
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
IN_R
IHBS
Figure 6-7. Input Rising Threshold
VHB=VHS=100V
Figure 6-6. HB to VSS Quiescent Current
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
1.145
1.14
280
270
260
250
240
230
1.135
1.13
1.125
1.12
1.115
1.11
8V
12V
16V
1.105
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
IN_F
R_IN
Figure 6-8. Input Falling Threshold
Figure 6-9. Input Pull-down Resistor
7.6
7.5
7.4
7.3
7.2
7.1
7
6.8
6.6
6.4
6.2
6
6.9
6.8
5.8
5.6
Rise
Fall
Rise
Fall
5.4
6.7
6.6
-40 -20
0
20 40 60 80 100 120 140
Temperature (°C)
-40 -20
0
20 40 60 80 100 120 140
Temperature (°C)
VDD_
HB_U
Figure 6-10. VDD UVLO Threshold
Figure 6-11. HB UVLO Threshold
0.14
0.12
0.1
0.22
0.2
0.18
0.16
0.14
0.12
0.1
0.08
8V
12V
16V
8V
12V
16V
0.06
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
V_LO
V_LO
IO=100mA
IO=-100mA
Figure 6-12. LO Low Output Voltage (VLOL
)
Figure 6-13. LO High Output Voltage (VLOH)
Copyright © 2020 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
0.16
0.2
0.18
0.16
0.14
0.12
0.1
0.14
0.12
0.1
8V
8V
12V
16V
12V
16V
0.08
0.08
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
UV_CHCO2
V_HO
IO=100mA
IO=-100mA
Figure 6-14. HO Low Output Voltage (VHOL
)
Figure 6-15. HO High Output Voltage (VHOH)
15
14
13
12
11
10
9
10.5
8V
8V
12V
16V
12V
16V
10
9.5
9
8.5
8
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
LO_F
LO_R
CL=1800pF
CL=1800pF
Figure 6-17. LO Fall Time
Figure 6-16. LO Rise Time
18
16
14
12
10
8
9
8.7
8.4
8.1
7.8
7.5
7.2
8V
12V
16V
8V
12V
16V
6
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
HO_F
HO_R
CL=1800pF
CL=1800pF
Figure 6-19. HO Fall Time
Figure 6-18. HO Rise Time
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
0.4
0.38
0.36
0.34
0.32
0.3
0.45
0.425
0.4
0.375
0.35
0.325
0.3
0.28
0.26
0.24
0.22
0.2
0.275
0.25
0.225
0.2
Rise
Fall
Rise
Fall
0.175
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
HO_R
LO_R
CL=100nF
VDD = 12 V
CL=100nF
VDD = 12 V
Figure 6-21. HO Rise & Fall Time
Figure 6-20. LO Rise & Fall Time
20
19
18
17
16
15
14
21
20
19
18
17
16
15
14
8V
12V
16V
8V
12V
16V
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
TDHR
TDHF
CL=No Load
CL= No Load
Figure 6-22. HO Rising Propagation Delay (TDHRR) Figure 6-23. HO Falling Propagation Delay (TDHFF)
20
19.5
19
19
18.5
18
18.5
18
17.5
17
17.5
17
16.5
16
16.5
16
15.5
15
8V
12V
16V
8V
12V
16V
15.5
15
14.5
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
-40
-20
0
20
40 60
Temperature (°C)
80
100 120 140
TDLR
TDLF
CL= No Load
CL= No Load
Figure 6-24. LO Rising Propagation Delay (TDLRR) Figure 6-25. LO Falling Propagation Delay (TDLFF)
Copyright © 2020 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
7 Detailed Description
7.1 Overview
The UCC27288 is a high-voltage gate driver designed to drive both the high-side and the low-side N-channel
FETs in a synchronous buck or a half-bridge configurations. The two outputs are independently controlled with
two TTL-compatible input signals. The device can also work with CMOS type control signals at its inputs as long
as signals meet turn-on and turn-off threshold specifications of the UCC27288. The floating high-side driver is
capable of working with HS voltage up to 100 V with respect to VSS. There is no internal bootstrap diode in the
UCC27288 device to charge high-side gate drive bootstrap capacitor. An external 100-V (minimum) rated boot
diode should be used if bootstrap bias supply is desired for the high-side output. It is also acceptable to use
higher voltage external bootstrap diode. A robust level shifter operates at high speed while consuming low power
and provides clean level transitions from the control logic to the high-side gate driver. Undervoltage lockout
(UVLO) is provided on both the low-side and the high-side power rails.
7.2 Functional Block Diagram
HB
UVLO
DRIVER
STAGE
HO
LEVEL
SHIFT
HS
HI
VDD
UVLO
DRIVER
STAGE
LO
VSS
LI
Copyright © 2018, Texas Instruments Incorporated
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
7.3 Feature Description
7.3.1 Start-up and UVLO
Both the high-side and the low-side driver stages include UVLO protection circuitry which monitors the supply
voltage (VDD) and the bootstrap capacitor voltage (VHB–HS). The UVLO circuit inhibits each output until sufficient
supply voltage is available to turn on the external MOSFETs. The built-in UVLO hysteresis prevents chattering
during supply voltage variations. When the supply voltage is applied to the VDD pin of the device, both the
outputs are held low until VDD exceeds the UVLO threshold, typically 7.0 V. Any UVLO condition on the
bootstrap capacitor (VHB–HS) disables only the high- side output (HO).
Table 7-1. VDD UVLO Logic Operation
Condition (VHB-HS > VHBR
HI
H
L
LI
L
HO
L
LO
L
H
H
L
L
L
VDD-VSS < VDDR during device start-up
H
L
L
L
L
L
H
L
L
L
L
H
H
L
L
L
VDD-VSS < VDDR – VDDH after device start-up
H
L
L
L
L
L
Table 7-2. HB UVLO Logic Operation
Condition (VDD > VDDR
HI
H
L
LI
L
HO
L
LO
L
H
H
L
L
H
H
L
VHB-HS < VHBR during device start-up
H
L
L
L
H
L
L
L
L
H
H
L
L
H
H
L
VHB-HS < VHBR – VHBH after device start-up
H
L
L
L
7.3.2 Input Stages
The two inputs operate independent of each other. The two inputs can overlap and output shall follow the input
signals. The independence allows for full control of two outputs compared to the gate drivers that have a single
input. There is no fixed time de-glitch filter implemented in the device and therefore propagation delay and delay
matching are not sacrificed. In other words, there is no built-in dead-time. If the dead time between two outputs
is desired then that shall be programmed through the micro-controller. If noise on the input signal is expected in
a way that could cause the inputs to overlap then the outputs shall follow the inputs and shoot-through may
occur. To avoid such situation small input filter shall be implemented at the front of the gate driver inputs, HI and
LI. Because the inputs are independent of supply voltage, they can be connected to outputs of either digital
controller or analog controller. Inputs can accept wide slew rate signals and input can withstand negative voltage
to increase the robustness. Small filter at the inputs of the driver further improves system robustness in noise
prone applications, as mentioned earlier. The inputs have internal pull down resistors with typical value of 250
kΩ. Thus, when the inputs are floating, the outputs are held low.
7.3.3 Level Shifter
The level shift circuit is the interface from the high-side input, which is a VSS referenced signal, to the high-side
driver stage which is referenced to the switch node (HS pin). The level shift allows control of the HO output
which is referenced to the HS pin. The delay introduced by the level shifter is kept as low as possible and
therefore the device provides excellent propagation delay characteristic and delay matching with the low-side
driver output. Low delay matching allows power stages to operate with less dead time. The reduction in dead-
time is very important in applications where high efficiency is required.
Copyright © 2020 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
7.3.4 Output Stage
The output stages are the interface from level shifter output to the power MOSFETs in the power train. High slew
rate, low resistance, and high peak current capability of both outputs allow for efficient switching of the power
MOSFETs. The low-side output stage is referenced to VSS and the high-side is referenced to HS. The device
output stages are robust to handle harsh environment, such as –2 V transient for 100 ns. The device can also
sustain positive transients on the outputs. The device output stages feature a pull-up structure which delivers the
highest peak source current when it is most needed, during the Miller plateau region of the power switch turn on
transition. The output pull-up and pull-down structure of the device is totem pole NMOS-PMOS structure.
7.3.5 Negative Voltage Transients
In most applications, the body diode of the external low-side power MOSFET clamps the HS node to ground. In
some situations, board capacitances and inductances can cause the HS node to transiently swing several volts
below ground, before the body diode of the external low-side MOSFET clamps this swing. When used in
conjunction with the UCC27288, the HS node can swing below ground as long as specifications are not violated
and conditions mentioned in this section are followed.
HS must always be at a lower potential than HO. Pulling HO more negative than specified conditions can
activate parasitic transistors which may result in excessive current flow from the HB supply. This may result in
damage to the device. The same relationship is true with LO and VSS. If necessary, a Schottky diode can be
placed externally between HO and HS or LO and VSS to protect the device from this type of transient. The diode
must be placed as close to the device pins as possible in order to be effective.
Ensure that the HB to HS operating voltage is 16 V or less. Hence, if the HS pin transient voltage is –5 V, then
VDD (and thus HB) is ideally limited to 11 V to keep the HB to HS voltage below 16 V. Generally when HS
swings negative, HB follows HS instantaneously and therefore the HB to HS voltage may not significantly
overshoot.
Low ESR bypass capacitors from HB to HS and from VDD to VSS are essential for proper operation of the gate
driver device. The capacitor should be located at the leads of the device to minimize series inductance. The
peak currents from LO and HO can be quite large. Any series inductances with the bypass capacitor causes
voltage ringing at the leads of the device which must be avoided for reliable operation.
Based on application board design and other operating parameters, along with HS pin, other pins such as
inputs, HI and LI, might also transiently swing below ground. To accommodate such operating conditions
UCC27288 input pins are capable of handling absolute maximum of -5V. As explained earlier, based on the
layout and other design constraints, some times the outputs, HO and LO, might also see transient voltages for
short durations. Therefore, UCC27288 gate drivers can also handle -2 V 100 ns transients on output pins, HO
and LO.
7.4 Device Functional Modes
The device operates in normal mode and UVLO mode. See Start-up and UVLO for more information on UVLO
operation mode. In normal mode when the VDD and VHB–HS are above UVLO threshold, the output stage is
dependent on the states of the HI and LI pins. The output HO and LO will be low if input state is floating.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
Table 7-3. Input/Output Logic in Normal Mode of Operation
HI
LI
HO (1)
LO (2)
H
H
H
L
H
L
L
L
L
H
L
H
H
L
L
L
H
L
L
L
L
H
H
L
L
L
Floating
Floating
L
L
H
Floating
Floating
Floating
H
Floating
(1) HO is measured with respect to HS
(2) LO is measured with respect to VSS
Copyright © 2020 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
8 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification, and TI
does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes. Customers should validate and test their design
implementation to confirm system functionality.
8.1 Application Information
Most electronic devices and applications are becoming more and more power hungry. These applications are
also reducing in overall size. One way to achieve both high power and low size is to improve the efficiency and
distribute the power loss optimally. Most of these applications employ power MOSFETs and they are being
switched at higher and higher frequencies. To operate power MOSFETs at high switching frequencies and to
reduce associated switching losses, a powerful gate driver is employed between the PWM output of controller
and the gates of the power semiconductor devices, such as power MOSFETs, IGBTs, SiC FETs, and GaN FETs.
Many of these applications require proper UVLO protection so that power semiconductor devices are turned ON
and OFF optimally. Also, gate drivers are indispensable when it is impossible for the PWM controller to directly
drive the gates of the switching devices. With the advent of digital power, this situation is often encountered
because the PWM signal from the digital controller is often a 3.3-V logic signal which cannot effectively turn on a
power switch. A level-shift circuit is needed to boost the 3.3-V signal to the gate-drive voltage (such as 12 V or 5
V) in order to fully turn-on the power device, minimize conduction losses, and minimize the switching losses.
Traditional buffer drive circuits based on NPN/PNP bipolar transistors in totem-pole arrangement prove
inadequate with digital power because they lack level-shifting capability and under voltage lockout protection.
Gate drivers effectively combine both the level-shifting and buffer-drive functions. Gate drivers also solve other
problems such as minimizing the effect of high-frequency switching noise (by placing the high-current driver
device physically close to the power switch), driving gate-drive transformers and controlling floating power device
gates. This helps reduce power dissipation and thermal stress in controllers by moving gate charge power losses
from the controller IC to the gate driver.
UCC27288 gate drivers offer high voltage (100 V), small delays (16 ns), and good driving capability (2.5 A/3.5 A)
in a single device. The floating high-side driver is capable of operating with switch node voltages up to 100 V.
This allows for N-channel MOSFETs control in half-bridge, full-bridge, synchronous buck, synchronous boost,
and active clamp topologies. UCC27288 gate driver IC does not have built-in bootstrap diode and therefore to
generate high-side bias from the VDD voltage an external boot diode shall be used. This allows users to select
application-appropriate external bootstrap diode such as fast recovery and low forward voltage drop Schottky
diode. Each channel is controlled by its respective input pins (HI and LI), allowing flexibility to control ON and
OFF state of the output.
Switching power devices such as MOSFETs have two main loss components; switching losses and conduction
losses. Conduction loss is dominated by current through the device and ON resistance of the device. Switching
losses are dominated by gate charge of the switching device, gate voltage of the switching device, and switching
frequency. Applications where operating switching frequency is high, the switching losses start to impact overall
system efficiency. In such applications, to reduce the switching losses it becomes essential to reduce the gate
voltage. The gate voltage is determined by the supply voltage the gate driver ICs, therefore, the gate driver IC
needs to operate at lower supply voltage in such applications. UCC27288 gate driver has typical UVLO level of
7.0V and therefore, they are perfectly suitable for applications where bias voltage need to be reduced from 12V
to 10V or even 9.5V. HB UVLO is lower than the VDD UVLO so that bootstrap diode voltage drop does not
inhibit this lower bias voltage opearion. There is enough UVLO hysteresis provided to avoid any chattering or
nuisance tripping which improves system robustness.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
8.2 Typical Application
10 V
75 V
VDD
DBoot
SECONDARY
SIDE
CIRCUIT
HB
HO
HI
DRIVE
HI
HS
LO
PWM
CONTROLLER
LI
DRIVE
LO
UCC27288
ISOLATION
AND
FEEDBACK
Copyright © 2020, Texas Instruments Incorporated
Figure 8-1. Typical Application
8.2.1 Design Requirements
Table below lists the system parameters. UCC27288 needs to operate satisfactorily in conjunction with them.
Table 8-1. Design Requirements
Parameter
MOSFET
Value
CSD19535KTT
75V
Maximum Bus/Input Voltage, Vin
Operating Bias Votage, VDD
Switching Frequency, Fsw
Total Gate Charge of FET at given VDD, QG
MOSFET Internal Gate Resistance, RGFET_Int
Maximum Duty Cycle, DMax
Gate Driver
10V
300kHz
52nC
1.4
0.5
UCC27288
8.2.2 Detailed Design Procedure
8.2.2.1 Select Bootstrap and VDD Capacitor
The bootstrap capacitor must maintain the VHB-HS voltage above the UVLO threshold for normal operation.
Calculate the maximum allowable drop across the bootstrap capacitor, ΔVHB, with Equation 1.
¿VHB = VDD F VDH F VHBL
:
;
= 10 V ꢀ 1 V ꢀ (7.1 V ꢀ 0.5 V) = 2.4 V
(1)
where
•
•
•
VDD is the supply voltage of gate driver device
VDH is the bootstrap diode forward voltage drop
VHBL is the HB falling threshold ( VHBR(max) – VHBH
)
In this example the allowed voltage drop across bootstrap capacitor is 2.4 V.
Copyright © 2020 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
It is generally recommended that ripple voltage on both the bootstrap capacitor and VDD capacitor should be
minimized as much as possible. Many of commercial, industrial, and automotive applications use ripple value of
0.5 V.
Use Equation 2 to estimate the total charge needed per switching cycle from bootstrap capacitor.
DMAX
QTOTAL = QG + IHBS × l
IHB
p + l
fSW
p
fSW
= 52 nC + 0.083 nC + 1.33 nC = 53.41 nC
(2)
where
•
•
•
•
QG is the total MOSFET gate charge
IHBS is the HB to VSS leakage current from datasheet
DMax is the converter maximum duty cycle
IHB is the HB quiescent current from the datasheet
The caculated total charge is 53.41 nC.
Next, use Equation 3 to estimate the minimum bootstrap capacitor value.
QTOTAL
53.41 nC
2.4 V
CBOOT
=
;
=
= 22.25 nF
:
min
¿VHB
(3)
The calculated value of minimum bootstrap capacitor is 22.25 nF. It should be noted that, this value of
capacitance is needed at full bias voltage. In practice, the value of the bootstrap capacitor must be greater than
calculated value to allow for situations where the power stage may skip pulse due to various transient conditions.
It is recommended to use a 100-nF bootstrap capacitor in this example. It is also recommenced to include
enough margin and place the bootstrap capacitor as close to the HB and HS pins as possible. Also place a small
size, 0402, low value, 1000 pF, capacitor to filter high frequency noise, in parallel with main bypass capacitor.
For this application, choose a CBOOT capacitor that has the following specifications: 0.1 µF, 25 V, X7R
As a general rule the local VDD bypass capacitor must be greater than the value of bootstrap capacitor value
(generally 10 times the bootstrap capacitor value). For this application choose a CVDD capacitor with the
following specifications: 1 µF , 25 V, X7R
CVDD capacitor is placed across VDD and VSS pin of the gate driver. Similar to bootstrap capacitors, place a
small size and low value capacitor in parallel with the main bypass capacitor. For this application, choose 0402,
1000 pF, capacitance in parallel with main bypass capacitor to filter high frequency noise.
The bootstrap and bias capacitors must be ceramic types with X7R dielectric or better. Choose a capacitor with a
voltage rating at least twice the maximum voltage that it will be exposed to. Choose this value because most
ceramic capacitors lose significant capacitance when biased. This value also improves the long term reliability of
the system.
8.2.2.2 External Bootstrap Diode and Series Resistor
The UCC27288 does not incorporate the bootstrap diode necessary to generate the high-side bias for HO to
work satisfactorily. The characteristics of this diode are important to achieve efficient, reliable operation. The
characteristics to consider are reverse voltage handling capability, repetitive peak forward current, forward
voltage drop, forward and reverse recovery time, and dynamic resistance. As the UCC27288 is 100V rated gate
driver, the external bootstrap diode must be at least 100V rated. Peak forward current rating depends on multiple
system parameters such as high-side and low-side duty cycle, value of bootstrap capacitor, value of series
resistor, and allowed voltage ripple on the bootstrap capacitor. Generally, low forward voltage drop diodes are
preferred for low power loss during charging of the bootstrap capacitor. Schottky diodes have low forward
voltage drop and can be used with the UCC27288. The dynamic characteristics to consider are diode recovery
time and stored charge. Diode that has less than 50ns of forward and reverse recovery times is suitable in most
applications.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
Specifically in very high switching frequency applications, for example in excess of 1 MHz, and where the low-
side minimum pulse widths are very small, the diode peak forward current could be very high and peak reverse
current could also be very high, specifically if high bootstrap capacitor value has been chosen. In such
applications it might be advisable to use Schottkey diode as bootstrap diode and provision of external series
resistor. MURS210 diode with 1 Ohm series resistor will work with the application example described here.
8.2.2.3 Estimate Driver Power Losses
The total power loss in gate driver device such as the UCC27288 is the summation of the power loss in different
functional blocks of the gate driver device. These power loss components are explained in this section.
1. Equation 4 describes how quiescent currents (IDD and IHB) affect the static power losses, PQC
.
: ; : ;
= VDD × IDD + VDD F VDH × IHB
PQC
= 10 V × 0.4 mA + 9 V × 0.4 mA = 7.6 mW
(4)
it is not shown here, but for more conservative approximation, add no load operating current, IDDO and IHBO in
above equation.
2. Equation 5 shows how high-side to low-side leakage current (IHBS) affects level-shifter losses (PIHBS).
P
IHBS
= VHB × IHBS × D = 85 V × 50 µA × 0.5 = 2.12 mW
(5)
where
•
•
D is the high-side MOSFET duty cycle
VHB is the sum of input voltage and voltage across bootstrap capacitor.
3. Equation 6 shows how MOSFETs gate charge (QG) affects the dynamic losses, PQG
.
RGD_R
PQG = 2 × VDD × QG × fSW
×
RGD _R+ RGATE + RGFET
:
int
;
= 2 × 10 V × 52 nC × 300 kHz × 0.74 = 0.23 W
(6)
where
•
•
•
•
•
QG is the total MOSFET gate charge
fSW is the switching frequency
RGD_R is the average value of pullup and pulldown resistor
RGATE is the external gate drive resistor
RGFET(int) is the power MOSFETs internal gate resistor
Assume there is no external gate resistor in this example. The average value of maximum pull-up and pull
down resistance of the driver output section is approximately 4 Ω. Substitute the application values to
calculate the dynamic loss due to gate charge, which is 230 mW here.
4. Equation 7 shows how parasitic level-shifter charge (QP) on each switching cycle affects dynamic losses,
(PLS) during high-side switching.
P = VHB × QP × fSW
LS
(7)
For this example and simplicity, it is assumed that value of parasitic charge QP is 1 nC. Substituting values
results in 25.5 mW as level shifter dynamic loss. This estimate is very high for level shifter dynamic losses.
The sum of all the losses is 265.22 mW as a total gate driver loss. As shown in this example, in most
applications the dynamic loss due to gate charge dominates the total power loss in gate driver device. For gate
drivers that include bootstrap diode, one should also estimate losses in bootstrap diode. Diode forward
conduction loss is computed as product of average forward voltage drop and average forward current.
Equation 8 estimates the maximum allowable power loss of the device for a given ambient temperature.
Copyright © 2020 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
www.ti.com
PMAX
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
kT F TAo
J
=
REJA
(8)
where
•
•
•
•
PMAX is the maximum allowed power dissipation in the gate driver device
TJ is the recommended maximum operating junction temperature
TA is hte ambient temperature of the gate driver device
RθJA is the junction-to-ambient thermal resistance
To better estimate the junction temperature of the gate driver device in the application, it is recommended to first
accurately measure the case temperature and then determine the power dissipation in a given application. Then
use ψJT to calculate junction temperature. After estimating junction temperature and measuring ambient
temperature in the application, calculate θJA(effective). Then, if design parameters (such as the value of an external
gate resistor or power MOSFET) change during the development of the project, use θJA(effective) to estimate how
these changes affect junction temperature of the gate driver device.
The Thermal Information table summarizes the thermal metrics for the driver package. For detailed information
regarding the thermal information table, please refer to the Semiconductor and Device Package Thermal Metrics
application report.
8.2.2.4 Selecting External Gate Resistor
In high-frequency switching power supply applications where high-current gate drivers such as the UCC27288
are used, parasitic inductances, parasitic capacitances and high-current loops can cause noise and ringing on
the gate of power MOSFETs. Often external gate resistors are used to damp this ringing and noise. In some
applications the gate charge, which is load on gate driver device, is significantly larger than gate driver peak
output current capability. In such applications external gate resistors can limit the peak output current of the gate
driver. it is recommended that there should be provision of external gate resistor whenever the layout or
application permits.
Use Equation 9 to calculate the driver high-side pull-up current.
VDD F VDH
RHOH + RGATE+ RGFET int
IOHH
=
:
;
(9)
where
•
•
•
IOHH is the high-side, peak pull-up current
VDH is the bootstrap diode forward voltage drop
RHOH is the gate driver internal high-side pull-up resistor. Value either directly provided in datasheet or can be
calculated from test conditions (RHOH = VHOH/IHO
)
•
•
RGATE is the external gate resistance connected between driver output and power MOSFET gate
RGFET(int) is the MOSFET internal gate resistance provided by MOSFET datasheet
Use Equation 10 to calculate the driver high-side sink current.
VDD F VDH
RHOL + RGATE+ RGFET int
IOLH
=
:
;
(10)
where
RHOL is the gate driver internal high-side pull-down resistance
•
Use Equation 11 to calculate the driver low-side source current.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
VDD
IOHL
=
RLOH + RGATE+ RGFET int
:
;
(11)
where
RLOH is the gate driver internal low-side pull-up resistance
•
Use Equation 12 to calculate the driver low-side sink current.
VDD
IOLL
=
RLOL + RGATE+ RGFET int
:
;
(12)
where
RLOL is the gate driver internal low-side pull-down resistance
•
Typical peak pull up and pull down current of the device is 2.5 A and 3.5 A respectively. These equations help
reduce the peak current if needed. To establish different rise time value compared to fall time value, external
gate resistor can be anti-paralleled with diode-resistor combination as shown in Figure 8-1. Generally selecting
an optimal value or configuration of external gate resistor is an iterative process. For additional information on
selecting external gate resistor please refer to External Gate Resistor Design Guide for Gate Drivers
8.2.2.5 Delays and Pulse Width
The total delay encountered in the PWM, driver and power stage need to be considered for a number of
reasons, primarily delay in current limit response. Also to be considered are differences in delays between the
drivers which can lead to various concerns depending on the topology. The synchronous buck topology
switching requires careful selection of dead-time between the high-side and low-side switches to avoid cross
conduction as well as excessive body diode conduction.
Bridge topologies can be affected by a volt-second imbalance on the transformer if there is imbalance in the
high-side and low-side pulse widths in any operating condition. The UCC27288 device has maximum
propagation delay, across process, and temperature variation, of 30 ns and delay matching of 7 ns, which is one
of the best in the industry.
Narrow input pulse width performance is an important consideration in gate driver devices, because output may
not follow input signals satisfactorily when input pulse widths are very narrow. Although there may be relatively
wide steady state PWM output signals from controller, very narrow pulses may be encountered under following
operating conditions.
•
•
•
soft-start period
large load transients
short circuit conditions
These narrow pulses appear as an input signal to the gate driver device and the gate driver device need to
respond properly to these narrow signals.
Figure 8-2 shows that the UCC27288 device produces reliable output pulse even when the input pulses are very
narrow. The propagation delay and delay matching do not get affected when the input pulse width is very narrow.
Copyright © 2020 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
HI (2V/div)
BW=1GHz
LI (2V/div)
BW=1GHz
LO (5V/div)
BW=1GHz
HO (5V/div)
BW=1GHz
Figure 8-2. Input and Output Pulse Width
8.2.2.6 VDD and Input Filter
Some switching power supply applications are extremely noisy. Noise may come from ground bouncing and
ringing at the inputs, (which are the HI and LI pins of the gate driver device). To mitigate such situations, the
UCC27288 offers both negative input voltage handling capability and wide input threshold hysteresis. If these
features are not enough, then the application might need an input filter. Small filter such as 10-Ω resistor and 47-
pF capacitor might be sufficient to filter noise at the inputs of the gate driver device. This RC filter would
introduce delay and therefore need to be considered carefully. High frequency noise on bias supply can cause
problems in performance of the gate driver device. To filter this noise it is recommended to use 1-Ω resistor in
series with VDD pin as shown in Figure 8-1. This resistor also acts as a current limiting element. In the event of
short circuit on the bias rail, this resistor opens up and prevents further damage. This resistor can also be helpful
in debugging the design during development phase.
8.2.2.7 Transient Protection
As mentioned in previous sections, high power high switching frequency power supplies are inherently noisy.
High dV/dt and dI/dt in the circuit can cause negative voltage on different pins such as HO, LO, and HS. The
device tolerates negative voltage on all of these pins as mentioned in specification tables. If parasitic elements of
the circuit cause very large negative swings, circuit might require additional protection. In such cases fast acting
and low leakage type Schottky diode should be used. This diode must be placed as close to the gate driver
device pin as possible for it to be effective in clamping excessive negative voltage on the gate driver device pin.
Sometimes a small resistor, (for example 2 Ω, in series with HS pin) is also effective in improving performance
reliability. To avoid the possibility of driver device damage due to over-voltage on its output pins or supply pins,
low leakage Zener diode can be used. A 15-V Zener diode is often sufficient to clamp the voltage below the
maximum recommended value of 16 V.
8.2.3 Application Curves
To minimize the switching losses in power supplies, turn-ON and turn-OFF of the power MOSFETs need to be as
fast as possible. Higher the drive current capability of the driver, faster the switching. Therefore, the UCC27288
is designed with high drive current capability and low resistance of the output stages. One of the common way to
test the drive capability of the gate driver device , is to test it under heavy load. Rise time and fall time of the
outputs would provide idea of drive capability of the gate driver device. There must not be any resistance in this
test circuit. Figure 8-3 and Figure 8-4 shows rise time and fall time of HO respectively of UCC27288. Figure 8-5
and Figure 8-6 shows rise time and fall time of LO respectively of UCC27288. For accuracy purpose, the VDD
and HB pin of the gate driver device were connected together. HS and VSS pins are also connected together for
this test.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
Peak current capability can be estimated using the fastest dV/dt along the rise and fall curve of the plot. This
method is also useful in comparing performance of two or more gate driver devices.
As explained in Section 8.2.2.5, propagation delay plays an important role in reliable operation of many
applications. Figure 8-7 and Figure 8-8
Figure 8-8 shows propagation delay and delay matching of UCC27288.
VDD=VHB=6 V, HS=VSS
CLOAD=10 nF
Ch4=HO
VDD=VHB=6 V, HS=VSS
CLOAD=10 nF
Ch4=HO
Figure 8-3. HO Rise Time
Figure 8-4. HO Fall Time
VDD=VHB=6 V, HS=VSS
CLOAD=10 nF Ch4=LO
VDD=VHB=6 V, HS=VSS
CLOAD=10 nF
Ch4=LO
Figure 8-5. LO Rise Time
Figure 8-6. LO Fall Time
Copyright © 2020 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
VDD=6 V
CLOAD=2 nF Ch1=HI Ch2=LI Ch3=HO Ch4=LO
VDD=6 V
CLOAD=2 nF
Ch1=HI Ch2=LI Ch3=HO Ch4=LO
Figure 8-7. Propagation Delay and Delay Matching
Figure 8-8. Propagation Delay and Delay Matching
VDD=10V Vin=100V
CL=1nF
Ch1=HI Ch2=LI Ch3=HO Ch4=LO
Figure 8-9. Input Negative Voltage
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
9 Power Supply Recommendations
The recommended bias supply voltage range for UCC27288 is from 8 V to 16 V. The lower end of this range is
governed by the internal under voltage-lockout (UVLO) protection feature, 7.0 V typical, of the VDD supply circuit
block. The upper end of this range is driven by the 16-V recomended maximum voltage rating of the VVDD. It is
recommended that voltage on VDD pin should be lower than maximum recommended voltage.
The UVLO protection feature also involves a hysteresis function. This means that once the device is operating in
normal mode, if the VDD voltage drops, the device continues to operate in normal mode as far as the voltage
drop do not exceeds the hysteresis specification, VDDHYS. If the voltage drop is more than hysteresis
specification, the device shuts down. Therefore, while operating at or near the 8-V range, the voltage ripple on
the auxiliary power supply output should be smaller than the hysteresis specification of UCC27288 to avoid
triggering device shutdown.
A local bypass capacitor should be placed between the VDD and GND pins. This capacitor should be located as
close to the device as possible. A low ESR, ceramic surface mount capacitor is recommended. It is
recommended to use two capacitors across VDD and GND: a low capacitance ceramic surface-mount capacitor
for high frequency filtering placed very close to VDD and GND pin, and another high capacitance value surface-
mount capacitor for device bias requirements. In a similar manner, the current pulses delivered by the HO pin
are sourced from the HB pin. Therefore, two capacitors across the HB to HS are recommended. One low value
small size capacitor for high frequency filtering and another one high capacitance value capacitor to deliver HO
pulses.
In applications where noise is very dominant and there is space on the PWB (Printed Wiring Board), it is
recommended to place a small RC filter at the inputs. This allows for improving the overall performance of the
design. In such applications. it is also recommended to have a place holder for power MOSFET external gate
resistor. This resistor allows the control of not only the drive capability but also the slew rate on HS, which
impacts the performance of the high-side circuit. If diode is used across the external gate resistor, it is
recommended to use a resistor in series with the diode, which provides further control of fall time.
In power supply applications such as motor drives, there exist lot of transients through-out the system. This
sometime causes over voltage and under voltage spikes on almost all pins of the gate driver device. To increase
the robustness of the design, it is recommended that the clamp diode should be used on HO and LO pins. If user
does not wish to use power MOSFET parasitic diode, external clamp diode on HS pin is recommended, which
needs to be high voltage high current type (same rating as MOSFET) and very fast acting. The leakage of these
diodes across the temperature needs to be minimal.
In power supply applications where it is almost certain that there is excessive negative HS voltage, it is
recommended to place a small resistor between the HS pin and the switch node. This resistance helps limit
current into the driver device up to some extent. This resistor will impact the high side drive capability and
therefore needs to be considered carefully.
Copyright © 2020 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
10 Layout
10.1 Layout Guidelines
To achieve optimum performance of high-side and low-side gate drivers, one must consider following printed
wiring board (PWB) layout guidelines.
•
Low ESR/ESL capacitors must be connected close to the device between VDD and VSS pins and between
HB and HS pins to support high peak currents drawn from VDD and HB pins during the turn-on of the
external MOSFETs.
•
•
To prevent large voltage transients at the drain of the top MOSFET, a low ESR electrolytic capacitor and a
good quality ceramic capacitor must be connected between the high side MOSFET drain and ground (VSS).
In order to avoid large negative transients on the switch node (HS) pin, the parasitic inductances between the
source of the high-side MOSFET and the source of the low-side MOSFET (synchronous rectifier) must be
minimized.
•
•
Overlapping of HS plane and ground (VSS) plane should be minimized as much as possible so that coupling
of switching noise into the ground plane is minimized.
Thermal pad should be connected to large heavy copper plane to improve the thermal performance of the
device. Generally it is connected to the ground plane which is the same as VSS of the device. It is
recommended to connect this pad to the VSS pin only.
•
Grounding considerations:
– The first priority in designing grounding connections is to confine the high peak currents that charge and
discharge the MOSFET gates to a minimal physical area. This confinement decreases the loop inductance
and minimize noise issues on the gate terminals of the MOSFETs. Place the gate driver as close to the
MOSFETs as possible.
– The second consideration is the high current path that includes the bootstrap capacitor, the bootstrap
diode, the local ground referenced bypass capacitor, and the low-side MOSFET body diode. The
bootstrap capacitor is recharged on a cycle-by-cycle basis through the bootstrap diode from the ground
referenced VDD bypass capacitor. The recharging occurs in a short time interval and involves high peak
current. Minimizing this loop length and area on the circuit board is important to ensure reliable operation.
10.2 Layout Example
HB Bypass
Capacitor (Top)
Gate Driver
(Top)
External Gate
Resistor (Top)
Input Filters
(Top)
Boot Diode
(Bottom)
VDD Bypass
Capacitors (Top)
External Gate
Resistor (Bottom)
Figure 10-1. Layout Example
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: UCC27288
UCC27288
SLUSE21A – JUNE 2020 – REVISED OCTOBER 2020
www.ti.com
11 Device and Documentation Support
11.1 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
11.2 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.3 Trademarks
TI E2E™ is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.5 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2020 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: UCC27288
PACKAGE OPTION ADDENDUM
www.ti.com
15-Oct-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
PUCC27288DR
UCC27288D
ACTIVE
ACTIVE
SOIC
SOIC
D
D
8
8
2500
75
TBD
Call TI
Call TI
-40 to 125
-40 to 125
Green (RoHS
& no Sb/Br)
NIPDAU
NIPDAU
Level-2-260C-1 YEAR
U288
U288
UCC27288DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
Level-2-260C-1 YEAR
-40 to 125
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
15-Oct-2020
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X (0 -15 )
4
5
8X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
.0028 MIN
[0.07]
ALL AROUND
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
相关型号:
UCC27288_V01
UCC27288 2.5-A/3.5-A 120V Half-Bridge Driver with 8V UVLO and No Internal Boostrap Diode
TI
UCC27288_V02
UCC27288 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and External Bootstrap Diode
TI
UCC27289
UCC27289 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and Negative Voltage Handling
TI
UCC27289D
UCC27289 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and Negative Voltage Handling
TI
UCC27289DPR
UCC27289 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and Negative Voltage Handling
TI
UCC27289DR
UCC27289 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and Negative Voltage Handling
TI
UCC27289DRC
UCC27289 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and Negative Voltage Handling
TI
UCC27289DRCR
UCC27289 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and Negative Voltage Handling
TI
UCC27289DRCT
UCC27289 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and Negative Voltage Handling
TI
UCC27289DRM
UCC27289 2.5-A/3.5-A 120-V Half-Bridge Driver with 8-V UVLO and Negative Voltage Handling
TI
©2020 ICPDF网 联系我们和版权申明