UC3710QPTR [TI]
暂无描述;UC1710
UC2710
UC3710
High Current FET Driver
FEATURES
DESCRIPTION
• Totem Pole Output with 6A
Source/Sink Drive
The UC1710 family of FET drivers is made with a high-speed Schottky pro-
cess to interface between low-level control functions and very high-power
switching devices-particularly power MOSFET’s. These devices accept
low-current digital inputs to activate a high-current, totem pole output which
can source or sink a minimum of 6A.
• 3ns Delay
• 20ns Rise and Fall Time into 2.2nF
• 8ns Rise and Fall Time into 30nF
• 4.7V to 18V Operation
Supply voltages for both V and V can independently range from 4.7V to
IN
C
18V. These devices also feature under-voltage lockout with hysteresis.
The UC1710 is packaged in an 8-pin hermetically sealed dual in-line pack-
age for –55°C to +125°C operation. The UC2710 and UC3710 are speci-
fied for a temperature range of –40°C to +85°C and 0°C to +70°C
respectively and are available in either an 8-pin plastic dual in-line or a
5-pin, TO-220 package. Surface mount devices are also available.
• Inverting and Non-Inverting Outputs
• Under-Voltage Lockout with
Hysteresis
• Thermal Shutdown Protection
• MINIDIP and Power Packages
ORDERING INFORMATION
TEMPERATURE
RANGE
PACKAGE
TRUTH TABLE
UC1710J
UC2710DW
UC2710J
UC2710N
UC2710T
UC3710DW
UC3710N
UC3710T
–55°C to +125°C
–40°C to +85°C
8 pin CDIP
INV
H
N.I.
H
Out
L
16 pin SOIC-wide
8 pin CDIP
OUT= INV and N.I.
OUT= INV or N.I.
8 pin PDIP
L
H
H
5 pin TO220
16 pin SOIC-wide
8 pin PDIP
H
L
L
0°C to +70°C
L
L
L
5 pin TO220
BLOCK DIAGRAM
INTERNALLY CONNECTED IN T PACKAGE
OUTPUT BIAS
5
VIN
4
VC
LOGIC BIAS
3
2
Out
N.I. IN
8
TSD
Pwr Gnd
INV IN
1
7
UVLO
Logic Gnd
INTERNALLY CONNECTED IN T PACKAGE
UDG-99079
05/99
UC1710
UC2710
UC3710
ABSOLUTE MAXIMUM RATINGS
N-Package
J-Package
T-Package
Supply Voltage, Vin . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V
Collector Supply Voltage, VC . . . . . . . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V
Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V . . . . . . . . . . . . . . 18V . . . . . . . . . . . . . . 18V
Output Current (Source or Sink)
±
Steady-State. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 500mA. . . . . . . . . . . . 500mA . . . . . . . . . . . . . ± 1A
Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3V-VIN . . . . . . . . –0.3V – VIN . . . . . . . . –0.3V – VIN
Power Dissipation at Ta=25°C . . . . . . . . . . . . . . . . . . . 1W. . . . . . . . . . . . . . . 1W. . . . . . . . . . . . . . . 3W
Power Dissipation at T (Case) = 25°C. . . . . . . . . . . . . . 2W. . . . . . . . . . . . . . . 2W. . . . . . . . . . . . . . 25W
Operating Junction Temperature. . . . . . . –55°C to +150°C . . . . –55°C to +150°C . . . . –55°C to +150°C
Storage Temperature . . . . . . . . . . . . . . . –65°C to +150°C . . . . –65°C to +150°C . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 seconds) . . . . . . . 300°C . . . . . . . . . . . . 300°C . . . . . . . . . . . . 300°C
Note 1: All currents are positive into, negative out of the specified terminal.
Note 2: Consult Unitrode Integrated Circuits databook for information regarding thermal specifications
and limitations of packages.
CONNECTION DIAGRAMS
DIL-8 MINIDIP (Top View)
J or N Package
SOIC-16 (Top View)
DW Package
5-Pin TO-220 (Top View)
T Package
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for VIN = VC = 15V, No load,
TA = TJ.
PARAMETERS
VIN Supply Current
TEST CONDITIONS
VIN =18V, VC =18V, Output Low
VIN =18V, VC =18V, Output High
VIN =18V, VC =18V, Output Low
VIN =18V, VC =18V,Output High
VIN High to Low
MIN
TYP
26
MAX UNITS
35
30
5.0
8
mA
mA
mA
mA
V
21
VC Supply Current
UVLO Threshold
1.5
5.0
4.1
4.4
3.8
4.1
4.4
4.8
VIN Low to High
V
2
UC1710
UC2710
UC3710
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for VIN = VC = 15V, No load,
TA = TJ.
PARAMETERS
TEST CONDITIONS
MIN
TYP
MAX UNITS
UVLO Threshold Hysteresis
Digital Input Low Level
Digital Input High Level
Digital Input Current
0.1
0.3
0.5
0.8
V
V
2.0
V
Digital Input = 0.0V
–70
–4.0
1.35
3.2
µA
V
Output High Sat., VC – VO
IO= –100mA
IO= –6A
2.2
4.5
0.6
4.5
V
Output Low Sat., VO
IO= 100mA
IO= 6A
0.25
3.4
V
V
Thermal Shutdown
165
°C
From Inv., Input to Output (Note 3, 4):
Rise Time Delay
CL = 0
35
35
35
20
25
85
35
35
35
15
20
85
70
70
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
CL = 2.2nF
CL = 30nF
CL = 0
70
10% to 90% Rise
Fall Time Delay
90% to 10% Fall
40
CL = 2.2nF
CL = 30nF
CL = 0
40
150
70
CL = 2.2nF
CL = 30nF
CL = 0
70
80
40
CL = 2.2nF
CL = 30nF
40
150
From N.I. Input to Output (Note 3,4):
Rise Time Delay
CL = 0
35
35
35
20
25
85
35
35
35
15
20
85
30
70
70
70
40
40
150
70
70
80
40
50
150
40
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
mA
CL = 2.2nF
CL = 30nF
CL = 0
10% to 90% Rise
Fall Time Delay
90% to 10% Fall
CL = 2.2nF
CL = 30nF
CL = 0
CL = 2.2nF
CL = 30nF
CL = 0
CL = 2.2nF
CL = 30nF
TA = 25°C (Note 5) CL = 0
Total Supply Current at 200kHz Input
Switching Frequency
Note: 3. Delay measured from 50% input change to 10% output change.
Note: 4. Those parameters with CL = 30nF are not tested in production.
Note: 5. Inv. Input pulsed at 50% duty cycle with N.I. Input = 3V. or N.I. Input pulsed at 50% duty cycle with Inv. Input = 0V.
UNITRODE CORPORATION
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (603) 424-2410 FAX (603) 424-3460
3
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1999, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明