TRS3238IDBG4 [TI]
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION; 3V至5.5V多通道RS - 232线路驱动器/接收器【 15千伏ESD （ HBM ）保护
| 型号： | TRS3238IDBG4 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION |
| 文件： | 总19页 (文件大小：367K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
FEATURES
DB OR PW PACKAGE
•
RS-232 Bus-Pin ESD Protection Exceeds
(TOP VIEW)
±15 kV Using Human-Body Model (HBM)
C2+
GND
C2−
C1+
27 V+
26
1
28
•
Meets or Exceeds the Requirements of
TIA/EIA-232-F and ITU v.28 Standards
2
3
V
CC
•
•
•
•
•
•
•
Operates With 3-V to 5.5-V VCC Supply
Operates up to 250 kbit/s
V−
4
25 C1−
DOUT1
DOUT2
DOUT3
RIN1
5
24 DIN1
Five Drivers and Three Receivers
Low Standby Current . . . 1 μA Typical
External Capacitors . . . 4 × 0.1 μF
Accepts 5-V Logic Input With 3.3-V Supply
6
23
22
21
20
19
18
17
16
15
DIN2
7
DIN3
8
ROUT1
ROUT2
DIN4
9
RIN2
DOUT4
RIN3
10
11
12
13
14
Always-Active Noninverting Receiver Output
(ROUT1B)
ROUT3
DIN5
DOUT5
FORCEON
FORCEOFF
•
Alternative High-Speed Pin-Compatible Device
(1 Mbit/s)
ROUT1B
INVALID
–
TRSF3238
APPLICATIONS
•
•
•
•
•
•
•
•
•
Battery-Powered Systems
PDAs
Notebooks
Subnotebooks
Laptops
Palmtop PCs
Hand-Held Equipment
Modems
Printers
DESCRIPTION/ORDERING INFORMATION
The TRS3238 consists of five line drivers, three line receivers, and a dual charge-pump circuit with ±15-kV ESD
(HBM) protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of
TIA/EIA-232-F and provides the electrical interface between notebook and subnotebook computer applications.
The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. In
addition, the device includes an always-active noninverting output (ROUT1B), which allows applications using
the ring indicator to transmit data while the device is powered down. The TRS3238 operates at data signaling
rates up to 250 kbit/s and a maximum of 30-V/μs driver output slew rate.
Flexible control options for power management are featured when the serial port and driver inputs are inactive.
The auto-powerdown plus feature functions when FORCEON is low and FORCEOFF is high. During this mode
of operation, if the device does not sense valid signal transitions on all receiver and driver inputs for
approximately 30 s, the built-in charge pump and drivers are powered down, reducing the supply current to
1 μA. By disconnecting the serial port or placing the peripheral drivers off, auto-powerdown plus occurs if there
is no activity in the logic levels for the driver inputs. Auto-powerdown plus can be disabled when FORCEON and
FORCEOFF are high. With auto-powerdown plus enabled, the device activates automatically when a valid signal
is applied to any receiver or driver input. INVALID is high (valid data) if any receiver input voltage is greater than
2.7 V or less than –2.7 V, or has been between –0.3 V and 0.3 V for less than 30 μs. INVALID is low (invalid
data) if all receiver input voltages are between –0.3 V and 0.3 V for more than 30 μs. Refer to Figure 5 for
receiver input levels.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2007, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
ORDERING INFORMATION
TA
PACKAGE(1)(2)
ORDERABLE PART NUMBER
TRS3238CDB
TOP-SIDE MARKING
Tube of 50
SSOP – DB
TSSOP – PW
SSOP – DB
TSSOP – PW
TRS3238C
Reel of 2000
Tube of 50
TRS3238CDBR
TRS3238CPW
0°C to 70°C
RS38C
Reel of 2000
Tube of 50
TRS3238CPWR
TRS3238IDB
TRS3238I
TRS38I
Reel of 2000
Tube of 50
TRS3238IDBR
–40°C to 85°C
TRS3238IPW
Reel of 2000
TRS3238IPWR
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
(2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
FUNCTION TABLES
Each Driver(1)
INPUTS
OUTPUT
DOUT
DRIVER STATUS
TIME ELAPSED SINCE LAST
RIN OR DIN TRANSITION
DIN
FORCEON
FORCEOFF
X
L
X
H
H
L
L
X
Z
H
L
Powered off
H
H
H
H
H
H
X
Normal operation with
auto-powerdown disabled
H
L
X
<30 s
<30 s
>30 s
>30 s
H
L
Normal operation with
auto-powerdown enabled
H
L
L
L
Z
Z
Powered off by
auto-powerdown plus feature
H
L
(1) H = high level, L = low level, X = irrelevant, Z = high impedance
Each Receiver(1)
INPUTS
FORCEOFF
OUTPUTS
RECEIVER STATUS
TIME ELAPSED SINCE LAST
RIN OR DIN TRANSITION
RIN1
RIN2–RIN3
ROUT1B
ROUT
L
H
X
X
L
L
X
L
H
L
Z
Z
H
L
Powered off while
ROUT1B is active
X
L
L
H
H
H
H
H
<30 s
<30 s
<30 s
>30 s
>30 s
L
H
L
Normal operation with
auto-powerdown plus
disabled/enabled
H
L
H
H
L
H
L
H
H
Open
Open
H
(1) H = high level, L = low level, X = irrelevant, Z = high impedance (off), Open = input disconnected or connected driver off
2
Submit Documentation Feedback
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
LOGIC DIAGRAM (POSITIVE LOGIC)
24
5
6
DIN1
DIN2
DOUT1
23
DOUT2
DOUT3
DOUT4
DOUT5
22
19
17
7
10
12
DIN3
DIN4
DIN5
14
13
FORCEOFF
FORCEON
15
Auto-Powerdown
Plus
INVALID
16
21
ROUT1B
ROUT1
8
RIN1
20
18
9
ROUT2
ROUT3
RIN2
RIN3
11
3
Submit Documentation Feedback
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
–0.3
–0.3
0.3
MAX
UNIT
VCC
Supply voltage range(2)
6
V
V+
Positive output supply voltage range(2)
Negative output supply voltage range(2)
Supply voltage difference(2)
7
V
V
V
V–
–7
V+ – V–
13
Driver (FORCEOFF, FORCEON)
Receiver
–0.3
–25
6
25
VI
Input voltage range
V
V
Driver
–13.2
–0.3
13.2
VO
θJA
Output voltage range
Receiver (INVALID)
DB package
VCC + 0.3
62
Package thermal impedance(3)(4)
°C/W
PW package
62
TJ
Operating virtual junction temperature
Storage temperature range
150
°C
°C
Tstg
–65
150
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to network GND.
(3) Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
(4) The package thermal impedance is calculated in accordance with JESD 51-7.
4
Submit Documentation Feedback
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
Recommended Operating Conditions(1)
See Figure 6
MIN
3
NOM
3.3
5
MAX UNIT
VCC = 3.3 V
3.6
V
Supply voltage
VCC = 5 V
4.5
2
5.5
VCC = 3.3 V
VCC = 5 V
VIH Driver and control high-level input voltage
VIL Driver and control low-level input voltage
DIN, FORCEOFF, FORCEON
V
2.4
DIN, FORCEOFF, FORCEON
DIN, FORCEOFF, FORCEON
0.8
5.5
25
70
85
V
V
Driver and control input voltage
0
–25
0
VI
Receiver input voltage
TRS3238C
TRS3238I
TA Operating free-air temperature
°C
–40
(1) Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
TEST CONDITIONS
MIN TYP(2)
MAX
UNIT
Input leakage
current
II
FORCEOFF, FORCEON
±0.01
±1
μA
No load,
Auto-powerdown plus disabled FORCEOFF and
FORCEON at VCC
0.5
1
2
10
10
mA
Supply current
(TA = 25°C)
ICC
Powered off
No load, FORCEOFF at GND
No load, FORCEOFF at VCC
Auto-powerdown plus enabled FORCEON at GND,
All RIN are open or grounded
,
μA
1
(1) Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
5
Submit Documentation Feedback
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
DRIVER SECTION
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
TEST CONDITIONS
MIN TYP(2)
MAX UNIT
VOH
VOL
IIH
High-level output voltage All DOUT at RL = 3 kΩ to GND
5
5.4
–5.4
±0.01
±0.01
±35
V
V
Low-level output voltage
High-level input current
Low-level input current
All DOUT at RL = 3 kΩ to GND
VI = VCC
–5
±1
±1
μA
μA
IIL
VI at GND
VCC = 3.6 V,
VO = 0 V
±60
±100
Short-circuit output
current(3)
IOS
ro
mA
Ω
VCC = 5.5 V,
VO = 0 V
±40
Output resistance
VCC, V+, and V– = 0 V,
VO = ±2 V
VO = ±12 V,
VO = ±10 V,
300
10M
VCC = 3 V to 3.6 V
±25
±25
Ioff
Output leakage current
FORCEOFF = GND
μA
VCC = 4.5 V to 5.5 V
(1) Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
(3) Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one
output should be shorted at a time.
Switching Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
TEST CONDITIONS
MIN
TYP(2)
MAX
UNIT
CL = 1000 pF,
One DOUT switching,
RL = 3 kΩ,
See Figure 1
Maximum data rate
150
250
kbit/s
CL = 150 pF to 2500 pF, RL = 3 kΩ to 7 kΩ,
See Figure 2
tsk(p)
Pulse skew(3)
100
ns
CL = 150 pF to 1000 pF
CL = 150 pF to 2500 pF
6
4
30
30
Slew rate, transition region
(see Figure 1)
VCC = 3.3 V,
RL = 3 kΩ to 7 kΩ
SR(tr)
V/μs
(1) Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
(3) Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
6
Submit Documentation Feedback
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
RECEIVER SECTION
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
High-level output voltage
Low-level output voltage
TEST CONDITIONS
IOH = –1 mA
MIN
TYP(2)
MAX UNIT
VOH
VOL
VCC – 0.6
VCC – 0.1
V
IOH = 1.6 mA
VCC = 3.3 V
VCC = 5 V
0.4
2.4
2.4
V
1.5
1.8
VIT+
Positive-going input threshold voltage
Negative-going input threshold voltage
V
VCC = 3.3 V
VCC = 5 V
0.6
0.8
1.2
VIT–
V
1.5
Vhys
Ioff
rI
Input hysteresis (VIT+ – VIT–
)
0.3
V
Output leakage current (except ROUT1B)
Input resistance
FORCEOFF = 0 V
±0.05
5
±10
μA
kΩ
VI = ±3 V to ±25 V
3
7
(1) Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Switching Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TYP(2)
UNIT
Propagation delay time, low- to high-level
output
tPLH
tPHL
ten
CL = 150 pF,
CL = 150 pF,
See Figure 3
150
ns
Propagation delay time, high- to low-level
output
See Figure 3
150
200
ns
ns
CL = 150 pF,
See Figure 4
RL = 3 kΩ,
Output enable time
tdis
Output disable time
Pulse skew(3)
CL = 150 pF,
See Figure 3
RL = 3 kΩ, See Figure 4
200
50
ns
ns
tsk(p)
(1) Testing supply conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.15 V; C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; and C1 = 0.047 μF
and C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
(3) Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
7
Submit Documentation Feedback
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
AUTO-POWERDOWN PLUS SECTION
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5)
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
Receiver input threshold for
INVALID high-level output voltage
VT+(valid)
VT–(valid)
VT(invalid)
VOH
FORCEON = GND,
FORCEOFF = VCC
FORCEOFF = VCC
2.7
V
Receiver input threshold for
INVALID high-level output voltage
FORCEON = GND,
FORCEON = GND,
–2.7
–0.3
V
V
V
V
Receiver input threshold for
INVALID low-level output voltage
FORCEOFF = VCC
FORCEON = GND,
0.3
0.4
IOH = –1 mA,
FORCEOFF = VCC
INVALID high-level output voltage
INVALID low-level output voltage
VCC – 0.6
IOH = 1.6 mA,
FORCEOFF = VCC
FORCEON = GND,
VOL
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5)
PARAMETER
Propagation delay time, low- to high-level output
Propagation delay time, high- to low-level output
Supply enable time
MIN
TYP(1)
0.1
MAX UNIT
tvalid
tinvalid
ten
μs
μs
μs
50
25
tdis
Receiver or driver edge to auto-powerdown plus
15
30
60
s
(1) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
8
Submit Documentation Feedback
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
PARAMETER MEASUREMENT INFORMATION
3 V
Input
RS-232
0 V
Output
Generator
(see Note B)
50 Ω
t
t
TLH
THL
C
L
R
L
(see Note A)
V
V
OH
3 V
−3 V
3 V
−3 V
3 V
FORCEOFF
Output
OL
6 V
tTHL or tTLH
SR(tr) +
TEST CIRCUIT
VOLTAGE WAVEFORMS
A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns,
tf ≤ 10 ns.
Figure 1. Driver Slew Rate
3 V
0 V
Input
1.5 V
1.5 V
RS-232
Output
Generator
(see Note B)
50 Ω
C
L
t
t
PLH
PHL
R
L
(see Note A)
V
V
OH
3 V
FORCEOFF
50%
50%
Output
OL
TEST CIRCUIT
A. CL includes probe and jig capacitance.
VOLTAGE WAVEFORMS
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns,
tf ≤ 10 ns.
Figure 2. Driver Pulse Skew
3 V or 0 V
FORCEON
3 V
−3 V
Input
1.5 V
1.5 V
Output
Generator
(see Note B)
t
t
PLH
PHL
50 Ω
C
L
(see Note A)
3 V
FORCEOFF
V
V
OH
50%
50%
Output
OL
TEST CIRCUIT
VOLTAGE WAVEFORMS
A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
Figure 3. Receiver Propagation Delay Times
9
Submit Documentation Feedback
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
PARAMETER MEASUREMENT INFORMATION (continued)
3 V
Input
1.5 V
1.5 V
V
CC
GND
3 V or 0 V
FORCEON
0 V
S1
t
PHZ
R
L
(S1 at GND)
V
OH
3 V or 0 V
Output
50%
Output
0.3 V
C
L
(see Note A)
FORCEOFF
50 Ω
t
t
PZL
PLZ
(S1 at V )
CC
(S1 at V )
CC
Generator
(see Note B)
0.3 V
Output
50%
V
OL
TEST CIRCUIT
A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.
C. tPLZ and tPHZ are the same as tdis
D. tPZL and tPZH are the same as ten
VOLTAGE WAVEFORMS
.
.
Figure 4. Receiver Enable and Disable Times
10
Submit Documentation Feedback
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
PARAMETER MEASUREMENT INFORMATION (continued)
Valid RS-232 Level, INVALID High
ROUT
2.7 V
Generator
(see Note B)
50 Ω
Indeterminate
0.3 V
If Signal Remains Within This Region
For More Than 30 µs, INVALID Is Low
0 V
†
−0.3 V
Indeterminate
Auto-
Powerdown
Plus
INVALID
−2.7 V
C = 30 pF
(see Note A)
L
Valid RS-232 Level, INVALID High
†
Auto-powerdown plus disables drivers and reduces
supply current to 1 µA.
FORCEOFF
FORCEON
DIN
DOUT
TEST CIRCUIT
NOTES: A. C includes probe and jig capacitance.
L
B. The pulse generator has the following
characteristics: PRR = 5 kbit/s, Z = 50 Ω, 50%
O
duty cycle, t ≤ 10 ns, t ≤ 10 ns.
r
f
3 V
2.7 V
Receiver
Input
0 V
0 V
−2.7 V
−3 V
t
invalid
t
valid
INVALID
Output
V
CC
50%
50%
0 V
3 V to 5 V
Driver
Input
50%
50%
0 V
≈5.5 V
Driver
Output
≈ −5.5 V
t
dis
t
dis
t
en
t
en
V+
V+
V+ −0.3 V
Supply
Voltages
V− +0.3 V
V−
V−
Voltage Waveforms and Timing Diagrams
Figure 5. INVALID Propagation-Delay Times and Supply-Enabling Time
11
Submit Documentation Feedback
TRS3238
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD (HBM) PROTECTION
www.ti.com
SLLS817–JULY 2007
APPLICATION INFORMATION
+
C
= 0.1 µF
BYPASS
−
28
27
C1+
V+
1
2
C2+
+
−
+
GND
†
C3
C2
+
−
−
C1
3
4
26
25
24
C2−
V−
V
CC
−
+
C1−
C4
5
6
7
8
9
DIN1
DIN2
DIN3
DOUT1
DOUT2
DOUT3
RIN1
23
22
21
20
ROUT1
ROUT2
RS-232 Port
RIN2
Logic I/Os
5 kΩ
10
11
19
18
DOUT4
RIN3
DIN4
ROUT3
5 kΩ
12
17
16
DOUT5
DIN5
ROUT1B
5 kΩ
Auto-
Powerdown
Plus
13
14
15
FORCEON
FORCEOFF
INVALID
V
CC
vs CAPACITOR VALUES
V
CC
C1
C2, C3, and C4
†
C3 can be connected to V or GND.
CC
3.3 V ± 0.15 V
3.3 V ± 0.3 V
5 V ± 0.5 V
0.1 µF
0.22 µF
0.047 µF
0.22 µF
0.1 µF
0.22 µF
0.33 µF
1 µF
NOTES: A. Resistor values shown are nominal.
B. Nonpolarizedceramic capacitors are acceptable. If polarized tantalum
or electrolytic capacitors are used, they should be connected as
shown.
3 V to 5.5 V
Figure 6. Typical Operating Circuit and Capacitor Values
12
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jul-2010
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Request Free Samples
TRS3238CDB
TRS3238CDBG4
TRS3238CDBR
TRS3238CDBRG4
TRS3238CPW
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SSOP
SSOP
DB
DB
DB
DB
PW
PW
PW
28
28
28
28
28
28
28
TBD
TBD
TBD
TBD
TBD
TBD
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
SSOP
SSOP
TSSOP
TSSOP
TSSOP
TRS3238CPWG4
TRS3238CPWR
2000
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TRS3238CPWRG4
ACTIVE
TSSOP
PW
28
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
TRS3238IDB
TRS3238IDBG4
TRS3238IDBR
TRS3238IDBRG4
TRS3238IPW
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SSOP
SSOP
DB
DB
DB
DB
PW
PW
PW
28
28
28
28
28
28
28
TBD
TBD
TBD
TBD
TBD
TBD
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Request Free Samples
SSOP
SSOP
TSSOP
TSSOP
TSSOP
TRS3238IPWG4
TRS3238IPWR
2000
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TRS3238IPWRG4
ACTIVE
TSSOP
PW
28
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jul-2010
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jul-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TRS3238CPWR
TRS3238CPWR
TRS3238IPWR
TRS3238IPWR
TSSOP
TSSOP
TSSOP
TSSOP
PW
PW
PW
PW
28
28
28
28
2000
2000
2000
2000
330.0
330.0
330.0
330.0
16.4
16.4
16.4
16.4
6.9
7.1
6.9
7.1
10.2
10.4
10.2
10.4
1.8
1.6
1.8
1.6
12.0
12.0
12.0
12.0
16.0
16.0
16.0
16.0
Q1
Q1
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jul-2010
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TRS3238CPWR
TRS3238CPWR
TRS3238IPWR
TRS3238IPWR
TSSOP
TSSOP
TSSOP
TSSOP
PW
PW
PW
PW
28
28
28
28
2000
2000
2000
2000
346.0
346.0
346.0
346.0
346.0
346.0
346.0
346.0
33.0
33.0
33.0
33.0
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
M
0,15
15
0,25
0,09
5,60
5,00
8,20
7,40
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
0,10
2,00 MAX
0,05 MIN
PINS **
14
16
20
24
28
30
38
DIM
6,50
5,90
6,50
5,90
7,50
8,50
7,90
10,50
9,90
10,50 12,90
A MAX
A MIN
6,90
9,90
12,30
4040065 /E 12/01
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
M
0,10
0,65
14
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°–8°
A
0,75
0,50
Seating Plane
0,10
0,15
0,05
1,20 MAX
PINS **
8
14
16
20
24
28
DIM
3,10
2,90
5,10
4,90
5,10
4,90
6,60
6,40
7,90
9,80
9,60
A MAX
A MIN
7,70
4040064/F 01/97
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
Automotive
www.ti.com/automotive
www.ti.com/communications
Communications and
Telecom
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Consumer Electronics
Energy
www.ti.com/consumer-apps
www.ti.com/energy
Logic
Industrial
www.ti.com/industrial
Power Mgmt
Microcontrollers
RFID
power.ti.com
Medical
www.ti.com/medical
microcontroller.ti.com
www.ti-rfid.com
Security
www.ti.com/security
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
Wireless
www.ti.com/video
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
相关型号：
TRS3238IDBR
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
TRS3238IDBRG4
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
TRS3238IPW
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
TRS3238IPWG4
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
TRS3238IPWR
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
TRS3238IPWRG4
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
TRS3238_10
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
TRS3243CDB
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
TRS3243CDBG4
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
TRS3243CDBR
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
TRS3243CDBRG4
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD (HBM) PROTECTION
TI
©2020 ICPDF网 联系我们和版权申明