TPS77401MDGKREP [TI]
250-mA LDO VOLTAGE REGULATOR WITH POWER-GOOD OUTPUT;
| 型号： | TPS77401MDGKREP |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 250-mA LDO VOLTAGE REGULATOR WITH POWER-GOOD OUTPUT 光电二极管 输出元件 调节器 |
| 文件： | 总23页 (文件大小：463K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
FEATURES
DGK PACKAGE
(TOP VIEW)
•
Controlled Baseline
– One Assembly
FB/SENSE
PG
8
7
6
5
OUT
OUT
IN
1
2
3
4
– One Test Site
– One Fabrication Site
EN
•
•
Extended Temperature Performance of –55°C
to 125°C
GND
IN
Enhanced Diminishing Manufacturing
Sources (DMS) Support
DROPOUT VOLTAGE
vs
JUNCTION TEMPERATURE
•
•
•
•
Enhanced Product-Change Notification
(1)
Qualification Pedigree
300
250
200
150
100
50
Open-Drain Power-Good (PG) Status Output
Available in 1.5-V, 1.8-V, 2.7-V, 2.8-V, 3.3-V,
5-V Fixed-Output and Adjustable Versions
I
O
= 250 mA
•
•
•
•
Dropout Voltage Typically 200 mV at 250 mA
Ultralow 92-µA Quiescent Current (Typ)
8-Pin MSOP (DGK) Package
Low Noise (55 µVrms) Without an External
Filter (Bypass) Capacitor
•
2% Tolerance Over Specified Conditions For
Fixed-Output Versions
I
O
= 10 mA
I
O
= 0 A
•
•
•
Fast Transient Response
0
Thermal Shutdown Protection
See the TPS779xx Family of Devices for
Active-High Enable
−50
−40
0
40
80
120
160
(1) Component qualification in accordance with JEDEC and
industry standards to ensure reliable operation over an
extended temperature range. This includes, but is not limited
to, Highly Accelerated Stress Test (HAST) or biased 85/85,
temperature cycle, autoclave or unbiased HAST,
T − Junction Temperature − °C
J
electromigration, bond intermetallic life, and mold compound
life. Such qualification testing should not be viewed as
justifying use of this component beyond specified
performance and environmental limits.
DESCRIPTION
The TPS77401 is a low-dropout (LDO) regulator with power good (PG) function. This device is capable of
supplying 250 mA of output current with a dropout of 200 mV. Quiescent current is 92 µA at full load dropping
down to 1 µA when device is disabled. This device is optimized to be stable with a wide range of output
capacitors including low-ESR ceramic (10-µF) or low-capacitance (1 µF) tantalum capacitors. This device has
extremely low noise output performance (55 µVrms) without using any added filter capacitors. The TPS77401 is
designed to have fast transient response for larger load current changes.
The TPS77401 is offered in 1.5-V, 1.8-V, 2.7-V, 2.8-V, 3.3-V, and 5-V fixed-voltage versions and in an
adjustable version (programmable over the range of 1.5 V to 5.5 V). Output voltage tolerance is 2% over line,
load, and temperature ranges. The TPS77401 device is available in an 8-pin mini small-outline package (MSOP)
(DGK).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2006, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
DESCRIPTION (CONTINUED)
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 200 mV at
an output current of 250 mA for 3.3-V option) and is directly proportional to the output current. Additionally, since
the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output
loading (typically 92 µA over the full range of output current, 0 mA to 250 mA). These two key specifications
yield a significant improvement in operating life for battery-powered systems.
The device is enabled when the enable (EN) pin is connected to a low-level input voltage. This LDO family also
features a sleep mode; applying a TTL high signal to EN shuts down the regulator, reducing the quiescent
current to less than 1 µA at TJ = 25°C.
For the TPS77401, the power good (PG) terminal is an active-high output, which can be used to implement a
power-on reset or a low-battery indicator. An internal comparator in the TPS77401 monitors the output voltage of
the regulator to detect an undervoltage condition on the regulated output voltage. When OUT falls below 82% of
its regulated voltage, PG goes to a low-impedance state. PG goes to a high-impedance state when OUT is
above 82% of its regulated voltage.
AVAILABLE OPTIONS(1)
OUTPUT VOLTAGE (V)
TYP
PACKAGED DEVICE MSOP (DGK)
ORDERABLE PART NUMBER SYMBOL
TPS77401MDGKREP BYQ
TJ
–55°C to 125°C
Adjustable 1.5 V to 5.5 V
(1) The TPS77401 is programmable using an external resistor divider (see application information). The DGK package is available taped
and reeled.
5
6
7
8
1
V
IN
IN
OUT
OUT
V
O
I
SENSE
PG
3
0.1 µF
2
EN
PG Output
10 µF
+
GND
4
Figure 1. Typical Application Configuration (for Fixed-Output Options)
2
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
FUNCTIONAL BLOCK DIAGRAMS
ADJUSTABLE VERSION
IN
EN
PG
_
+
OUT
+
_
R1
R2
220 ms Delay
V
ref
= 1.183 V
FB/SENSE
External to the Device
GND
FIXED-VOLTAGE VERSION
IN
EN
PG
_
+
OUT
SENSE
+
220 ms Delay
_
R1
R2
V
ref
= 1.183 V
GND
TERMINAL FUNCTIONS
TERMINAL
NAME
I/O
DESCRIPTION
NO.
1
FB/SENSE
PG
I
O
I
Feedback input voltage for adjustable device (sense input for fixed options)
2
Power good
EN
3
Enable
GND
IN
4
Regulator ground
Input voltage
5, 6
7, 8
I
OUT
O
Regulated output voltage
3
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
PG TIMING DIAGRAM
V
I
†
†
V
res
V
res
t
‡
‡
V
O
V
IT+
V
IT+
Threshold
Voltage
‡
‡
V
IT−
V
IT−
t
PG
Output
Output
Undefined
Output
Undefined
t
†
V
res
is the minimum input voltage for a valid PG. The symbol V is not currently listed within EIA or JEDEC standards for semiconductor
res
symbology.
‡
V
IT
− Trip voltage is typically 18% lower than the output voltage (82%V ) V to V is the hysteresis voltage.
O IT− IT+
4
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
–0.3
–0.3
MAX
13.5
16.5
16.5
UNIT
VI
Input voltage range(2)
V
V
V
Voltage range at EN
Maximum PG voltage
Peak output current
Internally limited
See Dissipation Rating Table
Continuous total power dissipation
Output voltage (OUT, FB)
Operating virtual junction temperature range(3)
Storage temperature range
ESD rating, Human-Body Model (HBM)
VO
Tj
5.5
125
150
2
V
–55
–65
°C
°C
kV
Tstg
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network terminal ground.
(3) Long-term high-temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of
overall device life. See http://www.ti.com/ep_quality for additional infomation on enhanced plastic packaging
Dissipation Ratings – Free-Air Temperatures
AIR FLOW
(CFM)
θJA
(°C/W)
θJC
(°C/W)
TA < 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
PACKAGE
0
266.2
255.2
242.8
3.84
3.92
4.21
376 mW
392 mW
412 mW
3.76 mW/°C
3.92 mW/°C
4.12 mW/°C
207 mW
216 mW
227 mW
150 mW
157 mW
165 mW
DGK
150
250
Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
MAX UNIT
VI
Input voltage(1)
2.7
1.5
0
10
5.5
V
V
VO
IO
Output voltage range
Output current(2)
Operating virtual junction temperature(2)
250
125
mA
°C
TJ
–55
(1) To calculate the minimum input voltage for your maximum output current, use the following equation: VI(min) = VO(max) + VDO(max load)
(2) Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
.
5
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
Electrical Characteristics
over recommended operating junction temperature range (TJ = –55°C to 125°C), VI = VO(typ) + 1 V, IO = 1 mA, EN = 0 V,
CO = 10 µF (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
0.98VO
TYP
MAX
1.02VO
UNIT
TJ = 125°C
Adjustable voltage
1.5 V ≤ VO ≤ 5.5 V
V
TJ = Full range
0.977VO
1.023VO
TJ = 25°C,
2.7 V < VIN < 10 V
1.5
1.8
1.5-V output
1.8-V output
2.7-V output
2.8-V output
3.3-V output
5-V output
V
V
2.7 V < VIN < 10 V
TJ = 25°C,
1.470
1.764
2.646
2.744
3.234
4.9
1.530
1.836
2.754
2.856
3.366
5.1
2.8 V < VIN < 10 V
3.7 V < VIN < 10 V
3.8 V < VIN < 10 V
4.3 V < VIN < 10 V
6 V < VIN < 10 V
2.8 V < VIN < 10 V
TJ = 25°C,
2.7
Output voltage(1)(2)
3.7 V < VIN < 10 V
TJ = 25°C,
2.8
3.8 V < VIN < 10 V
TJ = 25°C,
3.3
4.3 V < VIN < 10 V
TJ = 25°C,
5.0
V
6.0 V < VIN < 10 V
TJ = 25°C
92
Quiescent current (GND current)(1)(2)
µA
TJ = Full range
VO + 1 V < VI ≤ 10 V,
VO + 1 V < VI ≤ 10 V
TJ = 25°C
135
TJ = 25°C
0.005
%/V
%/V
mV
Output voltage line regulation (∆VO/VO)(3)
0.05
Load regulation
1
BW = 300 Hz to 100
kHz,
Output noise voltage
TJ = 25°C
55
µVrms
Output current limit
VO = 0 V
0.9
400
144
1.3
A
Peak output current
2 ms pulse width,
50% duty cycle
mA
°C
Thermal shutdown junction temperature
TJ = 25°C
1
3
1
Standby current
EN = VI
µA
TJ = Full range
FB input current
Adjustable voltage
FB = 1.5 V
µA
V
High-level enable input voltage
Low-level enable input voltage
Enable input current
2
0.7
1
V
–1
µA
dB
V
PSRR Power-supply rejection ratio
Minimum input voltage for valid PG
Trip threshold voltage
f = 1 kHz,
TJ = 25°C
55
I(PG) = 300 µA,
VO decreasing
Measured at VO
VI = 2.7 V,
V(PG) ≤ 0.8 V
1.1
79
85
%VO
PG
Hysteresis voltage
Output low voltage
Leakage current
0.5
I(PG) = 1 mA
0.15
0.4
1
V
V(PG) = 5 V
µA
(1) Minimum input operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater. Maximum input voltage = 10 V, minimum output current
1 mA.
(2) IO = 1 mA to 250 mA
(3) If VO < 1.8 V, then VI(max) = 10 V, VI(min) = 2.7 V:
OǒVI(max) * 2.7 VǓ
V
ǒ
Ǔ
Line regulation (mV) + %ńV
1000
100
If VO > 2.5 V, then VI(max) = 10 V, VI(min) = VO +*1 ǒVV:
Ǔ
OǒVI(max)
) 1 Ǔ
V
O
ǒ
Ǔ
Line regulation (mV) + %ńV
1000
100
6
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
Electrical Characteristics (continued)
over recommended operating junction temperature range (TJ = –55°C to 125°C), VI = VO(typ) + 1 V, IO = 1 mA, EN = 0 V,
CO = 10 µF (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
475
350
190
UNIT
IO = 250 mA,
IO = 250 mA
TJ = 25°C
270
2.8-V output
TJ = 25°C
200
125
Dropout
VDO
3.3-V output
5-V output
IO = 250 mA
mV
voltage(4)
TJ = Full Range
TJ = 25°C
IO = 250 mA,
IO = 250 mA
(4) IN voltage equals VO(typ) – 100 mV; 1.5-V, 1.8-V, and 2.7-V dropout voltage limited by input voltage range limitations (i.e., 3.3-V input
voltage needs to drop to 3.2-V for purpose of this test).
7
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
2, 3
4, 5
6
vs Output current
vs Junction temperature
vs Junction temperature
vs Frequency
Output voltage
Ground current
Power-supply rejection ratio
Output spectral noise density
Output impedance
7
vs Frequency
8
vs Frequency
9
vs Input voltage
10
Dropout voltage
vs Junction temperature
11
Line transient response
12, 14
13, 15
16
Load transient response
Output voltage and enable pulse
Equivalent series resistance
vs Time
vs Output current
18–21
TPS77x33
TPS77x18
OUTPUT VOLTAGE
vs
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT CURRENT
1.802
1.801
3.302
3.301
3.3
1.800
1.799
1.798
3.299
3.298
0
50
100
150
200
250
0
50
100
150
200
250
I
O
− Output Current − mA
I
O
− Output Current − mA
Figure 2.
Figure 3.
8
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
TPS77x33
OUTPUT VOLTAGE
vs
TPS77x18
OUTPUT VOLTAGE
vs
JUNCTION TEMPERATURE
JUNCTION TEMPERATURE
1.86
3.35
3.33
V = 2.8 V
I
V = 4.3 V
I
1.84
1.82
1.80
1.78
1.76
I
= 250 mA
O
3.31
3.29
I
O
I
O
I
O
= 1 mA
= 50 mA
= 250 mA
3.27
3.25
−40
0
40
80
120
160
−40
0
40
80
120
160
T − Junction Temperature − °C
J
T − Junction Temperature − °C
J
Figure 4.
Figure 5.
TPS77x33
TPS77xxx
GROUND CURRENT
vs
POWER SUPPLY REJECTION RATIO
vs
FREQUENCY
JUNCTION TEMPERATURE
115
110
105
100
90
80
70
60
50
40
30
20
10
0
C
= 10 µF
O
I
= 1 mA
T = 25 °C
J
O
100
95
I
= 1 mA
O
I
= 250 mA
O
90
85
I
O
= 250 mA
60
80
−40
10
110
160
10
100
1k
10k
100k
1M
10M
T − Junction Temperature − °C
J
f − Frequency − Hz
Figure 6.
Figure 7.
9
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
TPS77x33
TPS77x33
OUTPUT IMPEDANCE
vs
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
FREQUENCY
10
10
C
= 10 µF
O
T = 25 °C
J
T = 25 °C
J
I
O
= 250 mA
I
O
= 1 mA
1
1
I
O
= 1 mA
0.1
0.1
I
O
= 250 mA
0.01
0.01
100
1k
10k
100k
10
100
1k
10k
100k
1M
10M
f − Frequency − Hz
Figure 8.
f − Frequency − Hz
Figure 9.
TPS77x01
TPS77x33
DROPOUT VOLTAGE
vs
DROPOUT VOLTAGE
vs
INPUT VOLTAGE
JUNCTION TEMPERATURE
400
300
250
200
150
100
50
I
= 250 mA
O
350
300
T = 125 °C
I
O
= 250 mA
J
T = 25 °C
J
T = −40 °C
J
250
200
150
100
I
O
= 10 mA
I
O
= 0 A
0
50
0
−50
2.7
3.2
3.7
4.2
4.7
−40
0
40
80
120
160
V − Input Voltage − V
I
T − Junction Temperature − °C
J
Figure 10.
Figure 11.
10
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
TPS77x18
TPS77x18
LOAD TRANSIENT RESPONSE
LINE TRANSIENT RESPONSE
250
3.8
2.8
0
+50
10
0
0
−10
−50
C
= 10 µF
O
C
= 10 µF
O
T = 25 °C
J
T = 25 °C
J
I
O
= 250 mA
I
O
= 250 mA
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
t − Time − ms
1
t − Time − ms
Figure 12.
Figure 13.
TPS77x33
TPS77x33
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
250
0
5.3
4.3
10
0
0
−50
−10
C
O
= 10 µF
C
= 10 µF
O
T = 25 °C
T = 25 °C
J
J
−100
I
O
= 250 mA
I
O
= 250 mA
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
t − Time − ms
1
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
t − Time − ms
1
Figure 14.
Figure 15.
11
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
TPS77x33
OUTPUT VOLTAGE AND
ENABLE PULSE
vs
TIME (AT STARTUP)
C
O
= 10 µF
T = 25 °C
J
EN
0
0
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
t − Time − ms
Figure 16.
To Load
IN
V
I
OUT
+
R
L
C
O
EN
GND
ESR
Figure 17. Test Circuit for Typical Regions of Stability (Figure 18 through Figure 21)
(Fixed-Output Options)
12
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE
vs
†
†
EQUIVALENT SERIES RESISTANCE
vs
OUTPUT CURRENT
OUTPUT CURRENT
10
10
Region of Instability
Region of Instability
V
O
= 3.3 V
C
O
= 1 µF
V = 4.3 V
T = 25°C
J
I
1
Region of Stability
1
0.1
Region of Stability
V
O
= 3.3 V
C
O
= 10 µF
V = 4.3 V
I
T = 25°C
J
Region of Instability
150 200
Region of Instability
150 200
0.1
0.01
0
50
100
250
0
50
100
250
I
O
− Output Current − mA
I
O
− Output Current − mA
Figure 18.
Figure 19.
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE
vs
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE
vs
†
†
OUTPUT CURRENT
OUTPUT CURRENT
10
10
Region of Instability
Region of Instability
V
O
= 3.3 V
C
O
= 1 µF
V = 4.3 V
T = 125 °C
J
I
1
Region of Stability
1
0.1
Region of Stability
V
O
= 3.3 V
C
O
= 10 µF
V = 4.3 V
I
T = 125°C
J
Region of Instability
150 200
Region of Instability
150 200
0.01
0.1
0
50
I
100
250
0
50
100
250
− Output Current − mA
I
O
− Output Current − mA
O
Figure 20.
Figure 21.
13
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
APPLICATION INFORMATION
Pin Functions
Enable (EN)
The EN terminal is an input that enables or shuts down the device. If EN is a logic high, the device is in
shutdown mode. When EN goes to logic low, the device is enabled.
Power Good (PG)
The PG terminal is an open-drain, active-high output that indicates the status of Vout (output of the LDO). When
Vout reaches 82% of the regulated voltage, PG goes to a high-impedance state. It goes to a low-impedance state
when Vout falls below 82% (i.e., overload condition) of the regulated voltage. The open-drain output of the PG
terminal requires a pullup resistor.
Sense (SENSE)
The SENSE terminal of the fixed-output options must be connected to the regulator output, and the connection
should be as short as possible. Internally, SENSE connects to a high-impedance wide-bandwidth amplifier
through a resistor-divider network and noise pickup feeds through to the regulator output. It is essential to route
the SENSE connection in such a way to minimize/avoid noise pickup. Adding RC networks between the SENSE
terminal and Vout to filter noise is not recommended because it may cause the regulator to oscillate.
Feedback (FB)
FB is an input terminal used for the adjustable-output options and must be connected to an external feedback
resistor divider. The FB connection should be as short as possible. It is essential to route it in such a way to
minimize/avoid noise pickup. Adding RC networks between FB terminal and Vout to filter noise is not
recommended because it may cause the regulator to oscillate.
External Capacitor Requirements
An input capacitor is not usually required; however, a bypass capacitor (0.047 µF or larger) improves load
transient response and noise rejection if the device is located more than a few inches from the power supply. A
higher-capacitance capacitor may be necessary if large (hundreds of milliamps) load transients with fast rise
times are anticipated.
Most low-noise LDOs require an external capacitor to further reduce noise. This will impact the cost and board
space. The TPS77401 have very low noise specification requirements without using any external components.
Like all LDO regulators, the TPS77401 requires an output capacitor connected between OUT (output of the
LDO) and GND (signal ground) to stabilize the internal control loop. The minimum recommended capacitance
value is 1 µF, provided the ESR meets the requirement in Figure 19 and Figure 21. In addition, a low-ESR
capacitor can be used if the capacitance is at least 10 µF and the ESR meets the requirements in Figure 18 and
Figure 20. Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic capacitors are all suitable,
provided they meet the requirements previously described.
Ceramic capacitors have different types of dielectric material with each exhibiting different temperature and
voltage variation. The most common types are X5R, X7R, Y5U, Z5U, and NPO. The NPO type ceramic type
capacitors are generally the most stable over temperature. However, the X5R and X7R are also relatively stable
over temperature (with the X7R being the more stable of the two) and are, therefore, acceptable to use. The
Y5U and Z5U types provide high capacitance in a small geometry, but exhibit large variations over temperature;
therefore, the Y5U and Z5U are not generally recommended for use on this LDO. Independent of which type of
capacitor is used, one must make certain that at the worst-case condition, the capacitance/ESR meets the
requirements specified in Figure 18 through Figure 21.
Figure 22 shows the output capacitor and its parasitic impedances in a typical LDO output stage.
14
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
APPLICATION INFORMATION (continued)
I
O
LDO
−
R
ESR
V
ESR
+
+
V
I
V
O
R
LOAD
−
C
O
Figure 22. LDO Output Stage With Parasitic Resistances ESR
In steady state (dc state condition), the load current is supplied by the LDO (solid arrow) and the voltage across
the capacitor is the same as the output voltage (VCout = Vout). This means no current is flowing into the Cout
branch. If Iout suddenly increases (transient condition), the following occurs:
•
The LDO is not able to supply the sudden current need due to its response time (t1 in Figure 23). Therefore,
capacitor Cout provides the current for the new load condition (dashed arrow). Cout now acts like a battery
with an internal resistance, ESR. Depending on the current demand at the output, a voltage drop will occur
at RESR. This voltage is shown as VESR in Figure 22.
•
When Cout is conducting current to the load, initial voltage at the load is Vout = VCout – VESR. Due to the
discharge of Cout, the output voltage Vout drops continuously until the response time t1 of the LDO is reached
and the LDO resumes supplying the load. From this point, the output voltage starts rising again until it
reaches the regulated voltage. This period is shown as t2 in Figure 23.
The figure also shows the impact of different ESRs on the output voltage. The left brackets show different levels
of ESRs, where number 1 displays the lowest ESR and number 3 displays the highest ESR.
•
•
The higher the ESR, the larger the droop at the beginning of load transient.
The smaller the output capacitor, the faster the discharge time and the bigger the voltage droop during the
LDO response period.
Conclusion
To minimize the transient output droop, capacitors must have a low ESR and be large enough to support the
minimum output voltage requirement.
15
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
APPLICATION INFORMATION (continued)
I
out
V
out
1
2
ESR 1
ESR 2
3
ESR 3
t
1
t
2
Figure 23. Correlation of Different ESRs and Their Influence to the Regulation of Vout at a
Load Step From Low-to-High Output Current
16
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
APPLICATION INFORMATION (continued)
Programming the TPS77401 Adjustable LDO Regulator
The output voltage of the TPS77401 adjustable regulator is programmed using an external resistor divider as
shown in Figure 24. The output voltage is calculated using:
R1
R2
ǒ1 ) Ǔ
V
+ V
O
ref
(1)
Where:
Vref = 1.1834 V typ (the internal reference voltage)
Resistors R1 and R2 should be chosen for approximately 50-µA divider current. Lower-value resistors can be
used, but offer no inherent advantage and waste more power. Higher values should be avoided, as leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose R2 = 30.1 kΩ
to set the divider current at 50 µA and then calculate R1 using:
V
O
R1 +
* 1 R2
ǒ Ǔ
V
ref
(2)
OUTPUT VOLTAGE
PROGRAMMING GUIDE
TPS77401
OUTPUT
VOLTAGE
R1
R2
UNIT
PG
V
I
IN
PG Output
250 kΩ
0.1 µF
2.5 V
3.3 V
3.6 V
33.5
53.8
61.5
30.1
30.1
30.1
kΩ
kΩ
kΩ
EN
OUT
V
O
O
R1
C
NOTE: To reduce noise and prevent
oscillation,R1 and R2 need to be as close
as possible to the FB/SENSE terminal.
FB/SENSE
GND
R2
Figure 24. TPS77401 Adjustable LDO Regulator Programming
Regulator Protection
The TPS77401 PMOS-pass transistor has a built-in back diode that conducts reverse currents when the input
voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the
input and is not internally limited. When extended reverse voltage is anticipated, external limiting may be
appropriate.
The device also features internal current limiting and thermal protection. During normal operation, the TPS77401
limits output current to approximately 0.9 A. When current limiting engages, the output voltage scales back
linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device failure,
care should be taken not to exceed the power dissipation ratings of the package. If the temperature of the
device exceeds 150°C (typ), thermal-protection circuitry shuts it down. Once the device has cooled below 130°C
(typ), regulator operation resumes.
17
Submit Documentation Feedback
TPS77401-EP
250-mA LDO VOLTAGE REGULATOR
WITH POWER-GOOD OUTPUT
www.ti.com
SLVS702–OCTOBER 2006
APPLICATION INFORMATION (continued)
Power Dissipation and Junction Temperature
Specified regulator operation is ensured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation the
regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than or
equal to PD(max)
.
The maximum power dissipation limit is determined using the following equation:
T max * T
J
+
A
P
D(max)
R
qJA
Where:
TJmax = Maximum allowable junction temperature
RθJA = Thermal resistance, junction to ambient, for the package, i.e., 266.2°C/W for the 8-terminal MSOP with no
airflow
TA = Ambient temperature
The regulator dissipation is calculated using:
+ ǒVI * V
Ǔ
P
I
D
O
O
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation triggers the thermal
protection circuit.
18
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
TPS77401MDGKREP
V62/06663-01XE
Status (1)
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
MSOP
DGK
8
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
MSOP
DGK
8
2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS77401-EP :
Catalog: TPS77401
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Apr-2009
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0 (mm)
B0 (mm)
K0 (mm)
P1
W
Pin1
Diameter Width
(mm) W1 (mm)
(mm) (mm) Quadrant
TPS77401MDGKREP
MSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Apr-2009
*All dimensions are nominal
Device
Package Type Package Drawing Pins
MSOP DGK
SPQ
Length (mm) Width (mm) Height (mm)
358.0 335.0 35.0
TPS77401MDGKREP
8
2500
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Logic
Power Mgmt
Microcontrollers
RFID
Telephony
Video & Imaging
Wireless
RF/IF and ZigBee® Solutions www.ti.com/lprf
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明