TPS727XXDSE [TI]
TPS727 250-mA, Ultralow IQ, Fast Transient Response, RF Low-Dropout Linear Regulator;型号: | TPS727XXDSE |
厂家: | TEXAS INSTRUMENTS |
描述: | TPS727 250-mA, Ultralow IQ, Fast Transient Response, RF Low-Dropout Linear Regulator |
文件: | 总36页 (文件大小:1118K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
TPS727 250-mA, Ultralow IQ, Fast Transient Response,
RF Low-Dropout Linear Regulator
1 Features
3 Description
The TPS727 family of low-dropout (LDO) linear
regulators are ultralow quiescent current LDOs with
excellent line and ultra-fast load transient
performance and are designed for power-sensitive
applications. The LDO output voltage level is preset
by the use of innovative factory EEPROM
1
•
Very Low Dropout:
–
–
–
65 mV Typical at 100 mA
130 mV Typical at 200 mA
163 mV Typical at 250 mA
•
•
•
2% Accuracy Over Load, Line, Temperature
programming.
A
precision band-gap and error
Ultralow IQ: 7.9 μA
amplifier provides overall 2% accuracy over load, line,
and temperature extremes. The TPS727 family is
available in 1.5-mm × 1.5-mm SON and wafer chip-
scale (WCSP) packages that make the devices ideal
for handheld applications. This family of devices is
fully specified over a temperature range of TJ
–40°C to +125°C.
Excellent Load Transient Performance:±50 mV for
200 mA Loading and Unloading Transient
•
Available in Fixed-Output Voltages From 0.9 V to
5 V Using Innovative Factory EEPROM
Programming
=
•
•
•
•
High PSRR: 70 dB at 1 kHz
Stable with a 1.0-μF Ceramic Capacitor
Thermal Shutdown and Overcurrent Protection
Device Information
PART NUMBER
TPS727xxDSE
TPS727xxYFF
PACKAGE
WSON (6)
DSBGA (4)
BODY SIZE (NOM)
Available in 4-Ball, 0.4-mm Pitch Wafer-Level
1.50 mm × 1.50 mm
1.20 mm × 0.80 mm
Chip Scale and 1.5-mm × 1.5-mm SON Packages
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
2 Applications
•
•
•
•
•
Wireless Handsets, Smart Phones, PDAs
MP3 Players and Other Handheld Products
Wireless LAN, Bluetooth®, Zigbee®
Remote Controls
Portable Consumer Products
TYPICAL APPLICATION CIRCUIT
VIN
VOUT
IN
OUT
1mF
CIN
COUT
Ceramic
TPS727xx
On
Off
EN
GND
PSRR vs FREQUENCY
GROUND PIN CURRENT vs TEMPERATURE
15
12
9
100
VIN = 2.1V
IOUT = 0mA
90
80
70
IOUT = 10mA
60
50
40
30
20
10
0
6
3
IOUT = 200mA
0
10
100
1k
10k
100k
1M
10M
-40 -25 -10
5
20 35 50 65 80 95 110 125
Frequency (Hz)
Temperature (°C)
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
Table of Contents
7.4 Device Functional Modes........................................ 12
Applications and Implementation ...................... 13
8.1 Application Information............................................ 13
8.2 Typical Application .................................................. 13
8.3 Do's and Don'ts....................................................... 17
Power-Supply Recommendations...................... 17
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configurations and Functions....................... 4
Specifications......................................................... 5
6.1 Absolute Maximum Ratings ...................................... 5
6.2 ESD Ratings.............................................................. 5
6.3 Recommended Operating Conditions....................... 5
6.4 Thermal Information.................................................. 5
6.5 Electrical Characteristics........................................... 6
6.6 Typical Characteristics.............................................. 7
Detailed Description ............................................ 11
7.1 Overview ................................................................. 11
7.2 Functional Block Diagram ....................................... 11
7.3 Feature Description................................................. 11
8
9
10 Layout................................................................... 17
10.1 Layout Guidelines ................................................. 17
10.2 Layout Example .................................................... 18
11 Device and Documentation Support ................. 22
11.1 Documentation Support ........................................ 22
11.2 Community Resources.......................................... 22
11.3 Trademarks........................................................... 22
11.4 Electrostatic Discharge Caution............................ 22
11.5 Glossary................................................................ 22
7
12 Mechanical, Packaging, and Orderable
Information ........................................................... 22
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (September 2014) to Revision F
Page
•
Changed DSBGA body size in Device Information table ...................................................................................................... 1
Changes from Revision D (February 2014) to Revision E
Page
•
•
•
•
•
•
•
•
•
Added TPS727105 to document ............................................................................................................................................ 1
Changed terminal to pin throughout document ...................................................................................................................... 1
Updated Device Information table to current standards......................................................................................................... 1
Changed Pin Configurations note .......................................................................................................................................... 4
Changed Pin Functions table: reordered table by pin name, added I/O column ................................................................... 4
Updated Handling Ratings table to current standard ............................................................................................................. 5
Changed Thermal Information table: updated symbols.......................................................................................................... 5
Deleted new generation from first sentence of Overview section ........................................................................................ 11
Added note to Applications and Implementation section...................................................................................................... 13
Changes from Revision C (January, 2011) to Revision D
Page
•
•
•
•
•
Changed format to meet latest data sheet standards; added new sections and moved existing sections............................ 1
Deleted pinout diagrams from front page; see Pin Configurations and Functions section. ................................................... 1
Changed Pin Configurations section and moved to Pin Configurations and Functions section ............................................ 4
Changed note in Pin Configurations and Functions section. ................................................................................................. 4
Deleted Figure 26 and Figure 27.......................................................................................................................................... 17
Changes from Revision B (April, 2010) to Revision C
Page
•
•
•
Updated YFF front page pin drawing to show pin locations................................................................................................... 1
Revised Pin Configurations section ....................................................................................................................................... 4
Changed graph title for Figure 6............................................................................................................................................. 7
2
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
Changes from Revision A (September, 2009) to Revision B
Page
•
•
•
•
•
•
•
•
Updated Features list ............................................................................................................................................................. 1
Changed title of data sheet..................................................................................................................................................... 1
Changed footnote 2 to Absolute Maximum Ratings table ...................................................................................................... 5
Revised numerous specifications and parameters in Electrical Characteristics table ........................................................... 6
Revised operating parameters for Figure 4............................................................................................................................ 7
Replaced Figure 5 .................................................................................................................................................................. 7
Added operating parameters to Figure 6................................................................................................................................ 7
Updated Figure 9.................................................................................................................................................................... 7
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
3
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
5 Pin Configurations and Functions
TPS72715, TPS72718, TPS72728, TPS72748
All Other TPS727 Devices
YFF Package
DSBGA-4
YFF Package
DSBGA-4
Top View
Top View
OUT
GND
OUT
GND
B2
B1
B2
B1
A2
IN
A1
A2
IN
A1
EN
EN
See note.
See note.
DSE Package
1,5mm × 1,5mm WSON-6
Top View
OUT
NC
1
2
3
6
5
4
IN
NC
EN
GND
Tape and Reel
Sprocket Holes
Tape and Reel
Sprocket Holes
Top Dot
Mark
Top Dot
Mark
TPS72715YFF, TPS72718YFF
TPS72728YFF, TPS72748YFF
TPS727xxDSE
TPS72711YFF
(Example)
See Note
See Note
NOTE
The EN pin is marked with a dot for the 1.5-V, 1.8-V, 2.8-V, and 4.8-V versions of the YFF
package. The GND pin is marked with a dot for all other voltage versions of the YFF
package. Refer to YFF0004 Package Outline page included at the end of this document
for dimensions of the YFF package. On the package outline, the shaded box indicates the
location of ball A1 and does not correlate to any marking on the topside of the physical
package.
Pin Functions
PIN
I/O
NAME
EN
YFF
A1
B1
A2
—
DSE
4
DESCRIPTION
Enable pin. Driving EN over 0.9 V turns on the regulator. Driving EN below 0.4 V puts the regulator into shutdown
mode, thus reducing the operating current to 120 nA, nominal.
I
GND
IN
3
—
I
Ground pin.
Input pin. A small capacitor is needed from this pin to ground to assure stability. See Input and Output Capacitor
Requirements in the Application Information section for more details.
6
NC
2, 5
1
—
O
No connection. This pin can be tied to ground to improve thermal dissipation.
Regulated output voltage pin. A small 1-μF ceramic capacitor is needed from this pin to ground to assure stability.
See Input and Output Capacitor Requirements in the Application Information section for more details.
OUT
B2
4
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
6 Specifications
6.1 Absolute Maximum Ratings
at TJ = –40°C to +125°C (unless otherwise noted); all voltages are with respect to GND(1)
MIN
MAX
+6.0
+6.0(2)
UNIT
Input voltage range, VIN
–0.3
–0.3
–0.3
V
V
V
Enable voltage range, VEN
Output voltage range, VOUT
Maximum output current, IOUT
Output short-circuit duration
Operating junction temperature, TJ
Storage temperature, Tstg
+6.0
Internally limited
Indefinite
+150
–55
–55
°C
°C
+150
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
(2) VEN absolute maximum rating is VIN or 6.0 V, whichever is less.
6.2 ESD Ratings
VALUE
UNIT
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins(1)
±2000
V(ESD)
Electrostatic discharge
V
Charged device model (CDM), per JEDEC specification JESD22-C101,
all pins(2)
±500
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating junction temperature range (unless otherwise noted)
MIN
2
NOM
MAX
5.5
UNIT
VIN
IOUT
TJ
Input voltage
V
Output current
0
250
mA
°C
Operating junction temperature range
–40
+125
6.4 Thermal Information
TPS727
THERMAL METRIC(1)
DSE (WSON)
6 PINS
190.5
94.9
YFF (DSBGA)
UNITS
4 PINS
160
75
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
149.3
6.4
76
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance(2)
3
ψJB
152.8
N/A
74
RθJC(bot)
N/A
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
(2) θJCbot is not applicable because there is no thermal pad.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
5
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
6.5 Electrical Characteristics
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.3 V or 2.0 V, whichever is greater;
IOUT = 10 mA, VEN = 0.9 V, and COUT = 1.0 μF (unless otherwise noted). Typical values are at TJ = +25°C.
PARAMETER
Input voltage range
Output voltage range
TEST CONDITIONS
MIN
2.0
TYP
MAX
5.5
UNIT
V
VIN
VO
0.9
5.0
V
TJ = +25°C
–2.5
+2.5
mV
VOUT + 0.3 V ≤ VIN ≤ 5.5 V,
0 mA ≤ IOUT ≤ 200 mA
–2.0%
±1.0%
±1.0%
±50.0
±65
+2.0%
(1)
VOUT
DC output accuracy
Load transient
VOUT + 0.3 V ≤ VIN ≤ 5.5 V,
0 mA ≤ IOUT ≤ 250 mA
1 mA to 200 mA or
200 mA to 1 mA in 1 μs, COUT = 1 μF
ΔVOUT
mV
1 mA to 250 mA or
250 mA to 1 mA in 1 μs, COUT = 1 μF
VOUT(NOM) + 0.3 V ≤ VIN ≤ 5.5 V,
IOUT = 10 mA
ΔVO/ΔVIN Line regulation
ΔVO/ΔIOUT Load regulation
8
μV/V
0 mA ≤ IOUT ≤ 250 mA
20
6.5
μV/mA
VIN = 0.98 × VOUT(NOM), IOUT = 10 mA
VIN = 0.98 × VOUT(NOM), IOUT = 50 mA
VIN = 0.98 × VOUT(NOM), IOUT = 100 mA
VIN = 0.98 × VOUT(NOM), IOUT = 200 mA
VIN = 0.98 × VOUT(NOM), IOUT = 250 mA
VOUT = 0.9 × VOUT(NOM)
32.5
65
VDO
Dropout voltage(2)
mV
130
162.5
400
7.9
200
ICL
Output current limit
Ground pin current
300
550
12
mA
µA
IOUT = 0 mA, TJ = –40°C to +125°C
IOUT = 200 mA
IGND
110
130
0.12
IOUT = 250 mA
VEN ≤ 0.4 V, VIN = 2 V, TJ = +25°C
ISHDN
Shutdown current (IGND
)
µA
VEN ≤ 0.4 V, 2.0 V < VIN ≤ 4.5 V,
TJ = –40°C to +85°C
0.55
2
f = 10 Hz
85
75
70
55
40
45
f = 100 Hz
VIN = 2.3 V,
f = 1 kHz
PSRR
Power-supply rejection ratio
Output noise voltage
VOUT = 1.8 V,
IOUT = 10 mA
dB
f = 10 kHz
f = 100 kHz
f = 1 MHz
BW = 100 Hz to 100 kHz, VIN = 2.1 V,
VOUT = 1.8 V, IOUT = 10 mA
VN
33.5
100
μVRMS
tSTR
VHI
Startup time(3)
COUT = 1.0 μF, 0 ≤ IOUT ≤ 250 mA
μs
V
Enable pin high (enabled)
Enable pin low (disabled)
Enable pin current
0.9
0
VIN
0.4
VLO
IEN
V
EN = 5.5 V
40
1.90
500
1.95
nA
V
UVLO
Undervoltage lock-out
VIN rising
1.85
–40
Shutdown, temperature increasing
Reset, temperature decreasing
+160
+140
TSD
TJ
Thermal shutdown temperature
Operating junction temperature
°C
°C
+125
(1) The output voltage is programmed at the factory.
(2) VDO is measured for devices with VOUT(NOM) ≥ 2.35 V so that VIN ≥ 2.3 V.
(3) Startup time: time from EN assertion to 0.98 × VOUT(NOM)
.
6
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
6.6 Typical Characteristics
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.3 V or 2.0 V, whichever is greater; IOUT
10 mA, VEN = VIN, and COUT = 1.0 μF (unless otherwise noted). Typical values are at TJ = +25°C.
=
1.90
1.88
1.86
1.84
1.82
1.80
1.78
1.76
1.74
1.72
1.70
1.90
1.88
1.86
1.84
1.82
1.80
1.78
1.76
1.74
1.72
1.70
+125°C
+85°C
+25°C
-40°C
+125°C
+85°C
+25°C
-40°C
2.1
2.6
3.1
3.6
4.1
4.6
5.1
5.6
2.1
2.6
3.1
3.6
4.1
4.6
5.1
5.6
VIN (V)
VIN (V)
IOUT = 10 mA
IOUT = 200 mA
Figure 1. Line Regulation
(TPS72718)
Figure 2. Line Regulation
(TPS72718)
1.90
1.88
1.86
1.84
1.82
1.80
1.78
1.76
1.74
1.72
1.70
1.90
1.88
1.86
1.84
1.82
1.80
1.78
1.76
1.74
1.72
1.70
+125°C
+125°C
+85°C
+25°C
-40°C
+85°C
+25°C
-40°C
0
25
50
75 100 125 150 175 200 225 250
IOUT (mA)
0
1
2
3
4
5
6
7
8
9
10
IOUT (mA)
0 mA ≤ IOUT ≤ 250 mA
0 mA ≤ IOUT ≤ 10 mA
Figure 4. Load Regulation
(TPS72718)
Figure 3. Load Regulation Under Light Loads
(TPS72718)
160
140
120
100
80
160
140
120
100
80
60
60
40
40
+125°C
+85°C
+25°C
-40°C
+125°C
+85°C
+25°C
-40°C
20
20
0
0
0
50
100
150
200
250
2.25
2.75
3.25
3.75
4.25
4.75
VIN (V)
IOUT (mA)
IOUT = 200 mA
Figure 6. Dropout Voltage vs Input Voltage
Figure 5. Dropout Voltage vs Output Current (TPS72750)
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
7
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
Typical Characteristics (continued)
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.3 V or 2.0 V, whichever is greater; IOUT
=
10 mA, VEN = VIN, and COUT = 1.0 μF (unless otherwise noted). Typical values are at TJ = +25°C.
1.90
1.88
1.86
1.84
1.82
1.80
1.78
1.76
1.74
1.72
1.70
12.0
11.5
11.0
10.5
10.0
9.5
+125°C
+85°C
+25°C
-40°C
IOUT = 10 mA
9.0
IOUT = 200 mA
8.5
8.0
7.5
7.0
-40 -25 -10
5
20 35 50 65 80 95 110 125
2.1
2.6
3.1
3.6
4.1
4.6
5.1
5.6
Temperature (°C)
VIN (V)
IOUT = 0 mA
Figure 7. Output Voltage vs Temperature
(TPS72718)
Figure 8. Ground Pin Current vs Input Voltage
(TPS72718)
15
12
9
140
120
100
80
60
6
+125°C
40
+85°C
+25°C
-40°C
3
20
0
0
0
25
50
75 100 125 150 175 200 225 250
IOUT (mA)
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
VIN = 2.1 V, IOUT = 0 mA
0 mA ≤ IOUT ≤ 250 mA
Figure 10. Ground Pin Current vs Temperature
(TPS72718)
Figure 9. Ground Pin Current vs Load
(TPS72718)
550
500
450
400
350
2.0
1.6
1.2
0.8
0.4
0
+125°C
+85°C
+25°C
-40°C
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
VIN (V)
VIN (V)
Figure 11. Shutdown Current vs Input Voltage
(TPS72718)
Figure 12. Current Limit vs Input Voltage
(TPS72718)
8
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
Typical Characteristics (continued)
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.3 V or 2.0 V, whichever is greater; IOUT
10 mA, VEN = VIN, and COUT = 1.0 μF (unless otherwise noted). Typical values are at TJ = +25°C.
=
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
IOUT = 10 mA
IOUT = 10 mA
IOUT = 200 mA
IOUT = 200 mA
1M 10M
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
Figure 13. PSRR vs Frequency
(VIN – VOUT = 0.5 V, TPS72718)
Figure 14. PSRR vs Frequency
(VIN – VOUT = 0.3 V, TPS72718)
80
70
60
50
40
30
20
10
0
10.00
1.00
0.10
0.01
0
1 kHz
10 kHz
100 kHz
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
10
100
1k
10k
100k
1M
10M
VIN (V)
Frequency (Hz)
IOUT = 10 mA, CIN = COUT = 1 µF
Figure 15. PSRR vs Input Voltage
(TPS72718)
Figure 16. Output Spectral Noise Density vs Output Voltage
(TPS72718)
200 mA
IOUT
200 mA
IOUT
1 mA
0.1 mA
VOUT
VOUT
100 ms/div
50 ms/div
VIN = 2.3 V, tR = tF = 1 µs
VIN = 2.3 V, tR = tF = 1 µs
Figure 17. Load Transient Response: 0.1 mA to 200 mA
(TPS72718)
Figure 18. Load Transient Response: 1 mA to 200 mA
(TPS72718)
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
9
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
Typical Characteristics (continued)
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.3 V or 2.0 V, whichever is greater; IOUT
=
10 mA, VEN = VIN, and COUT = 1.0 μF (unless otherwise noted). Typical values are at TJ = +25°C.
200 mA
VOUT
IOUT
10 mA
2.7 V
VOUT
VIN
2.1 V
1 ms/div
50 ms/div
Slew rate = 1 V/µs, IOUT = 100 µA
VIN = 2.3 V, tR = tF = 1 µs
Figure 20. Line Transient Response
(TPS72718)
Figure 19. Load Transient Response: 10 mA to 200 mA
(TPS72718)
EN
VOUT
VOUT
2.7 V
VIN
IIN
2.1 V
100 ms/div
20 ms/div
Slew rate = 1 V/µs, IOUT = 200 µA
VIN = 2.1 V, VOUT = 1.8 V, IOUT = 100 µA
Figure 21. Line Transient Response
(TPS72718)
Figure 22. VIN Inrush Current
(TPS72718)
EN
VIN
VOUT
VOUT
IIN
200 ms/div
20 ms/div
IOUT = 200 mA
VIN = 2.1 V, VOUT = 1.8 V, IOUT = 200 mA
Figure 24. VIN Ramp Up, Ramp Down Response
(TPS72718)
Figure 23. VIN Inrush Current
(TPS72718)
10
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
7 Detailed Description
7.1 Overview
The TPS727 devices belong to a family of LDO regulators that consume extremely low quiescent current while
simultaneously delivering excellent PSRR with very little headroom (VIN – VOUT differential voltage), and very
good transient response. These features, combined with low noise without a noise reduction pin in an ultrasmall
package, make these devices ideal for portable applications. This family of regulators offers sub-band-gap output
voltages, current limit and thermal protection, and is fully specified from –40°C to +125°C.
7.2 Functional Block Diagram
IN
OUT
Current
Limit
Thermal
Shutdown
UVLO
EEPROM
Bandgap
EN
LOGIC
7.3 Feature Description
7.3.1 Internal Current Limit
The TPS727 internal current limit helps protect the regulator during fault conditions. During current limit, the
output sources a fixed amount of current that is largely independent of output voltage. In such a case, the output
voltage is not regulated and is VOUT = ILIMIT × RLOAD. The PMOS pass transistor dissipates (VIN – VOUT) × ILIMIT
until thermal shutdown is triggered and the device is turned off. As the device cools down, it is turned on by the
internal thermal shutdown circuit. If the fault condition continues, the device cycles between current limit and
thermal shutdown. See the Thermal Protection section for more details.
The PMOS pass element in the TPS727 has a built-in body diode that conducts current when the voltage at the
OUT pin exceeds the voltage at the IN pin. This current is not limited, so if extended reverse voltage operation is
anticipated, external limiting to 5% of rated output current is recommended.
7.3.2 Soft Start
The startup current is given by Equation 1:
ISOFT START (mA) = COUT(mF) ´ 0.07(V/ms) + ILOAD(mA)
(1)
Equation 1 shows that soft-start current is directly proportional to COUT
.
The output voltage ramp rate is independent of COUT and load current, and has a typical value of 0.07 V/μs.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
11
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
Feature Description (continued)
The TPS727 automatically adjusts the soft-start current to supply both the load current and the COUT charge
current. For example, if ILOAD = 0 mA upon enabling the LDO, ISOFT START = 1 μF × 0.07 V/μs + 0 mA = 70 mA,
the current that charges the output capacitor.
If ILOAD = 200 mA, ISOFT START = 1 μF × 0.07 V/μs + 200 mA = 270 mA, the current required for charging output
capacitor and supplying the load current.
If the output capacitor and load are increased such that the soft-start current exceeds the output current limit, the
current is clamped at the typical current limit of 400 mA. For example, if COUT = 10 μF and IOUT = 200 mA, 10 μF
× 0.07 V/μs + 200 mA = 900 mA is not supplied. Instead, the current is clamped at 400 mA.
7.3.3 Shutdown
The enable pin (EN) is active high and is compatible with standard and low voltage, TTL-CMOS levels. When
shutdown capability is not required, EN can be connected to the IN pin.
7.3.4 Dropout Voltage
The TPS727 uses a PMOS pass transistor to achieve low dropout. When (VIN – VOUT) is less than the dropout
voltage (VDO), the PMOS pass device is in the linear region of operation and the input-to-output resistance is the
RDS(ON) of the PMOS pass element. VDO approximately scales with output current because the PMOS device
functions like a resistor in dropout.
As with any linear regulator, PSRR and transient response are degraded as (VIN – VOUT) approaches dropout.
This effect is illustrated in Figure 15 in the Typical Characteristics section.
7.3.5 Undervoltage Lock-out (UVLO)
The TPS727 uses an undervoltage lock-out circuit that keeps the output shut off until the input voltage reaches
the UVLO threshold voltage.
7.3.6 Thermal Protection
Thermal protection disables the output when the junction temperature rises to approximately +160°C, allowing
the device to cool. When the junction temperature cools to approximately +140°C the output circuitry is again
enabled. Depending on power dissipation, thermal resistance, and ambient temperature, the thermal protection
circuit may cycle on and off. This cycling limits the dissipation of the regulator, protecting it from damage as a
result of overheating.
Any tendency to activate the thermal protection circuit indicates excessive power dissipation or an inadequate
heatsink. For reliable operation, limit junction temperature to +125°C maximum. To estimate the margin of safety
in a complete design (including heatsink), increase the ambient temperature until the thermal protection is
triggered; use worst-case loads and signal conditions. For good reliability, thermal protection triggers at least
+35°C above the maximum expected ambient condition of a particular application. This configuration produces a
worst-case junction temperature of +125°C at the highest expected ambient temperature and worst-case load.
The internal protection circuitry of the TPS727 is designed to protect against overload conditions. This circuitry is
not intended to replace proper heatsinking. Continuously running the TPS727 into thermal shutdown degrades
device reliability.
7.4 Device Functional Modes
7.4.1 Operation with EN Control
Driving EN over 0.9 V turns on the regulator. Driving EN below 0.4 V puts the regulator into shutdown mode,
thus reducing the operating current to 120 nA, nominal.
12
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
8 Applications and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The TPS727 family of low-dropout (LDO) linear regulators are utralow quiescent current LDOs with excellent line
and ultra-fast load transient performance and are designed for power-sensitive applications.
8.2 Typical Application
Figure 25. TPS72718YFF 2.5 VIN to 1.8 VOUT at 200 mA Schematic
8.2.1 Design Requirements
8.2.1.1 Input and Output Capacitor Requirements
Although an input capacitor is not required for stability, good analog design practice is to connect a 0.1-μF to
1.0-μF low equivalent series resistance (ESR) capacitor across the IN pin and GND input of the regulator. This
capacitor counteracts reactive input sources and improves transient response, noise rejection, and ripple
rejection. A higher-value capacitor may be necessary if large, fast rise-time load transients are anticipated, or if
the device is not located close to the power source. If source impedance is not sufficiently low, a 0.1-μF input
capacitor may be necessary to ensure stability.
The TPS727 is designed to be stable with standard ceramic capacitors with values of 1.0 μF or larger at the
output. X5R- and X7R-type capacitors are best because they have minimal variation in value and ESR over
temperature. Maximum ESR must be less than 200 mΩ.
8.2.1.2 Transient Response
As with any regulator, increasing the size of the output capacitor reduces over- and undershoot magnitude but
increases duration of the transient response.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
13
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
Typical Application (continued)
8.2.2 Detailed Design Procedure
Select the desired device based on the output voltage.
Provide an input supply with adequate headroom to include dropout and output current to account for the GND
pin current and to power the load.
Select adequate input and output capacitors.
The startup current is given by Equation 2:
ISOFT START (mA) = COUT(mF) ´ 0.07(V/ms) + ILOAD(mA)
(2)
Equation 2 shows that soft-start current is directly proportional to COUT
.
The output voltage ramp rate is independent of COUT and load current and has a typical value of 0.07 V/μs.
The TPS727 automatically adjusts the soft-start current to supply both the load current and the COUT charge
current. For example, if ILOAD = 0 mA upon enabling the LDO, ISOFT START = 1 μF × 0.07 V/μs + 0 mA = 70 mA,
the current that charges the output capacitor.
If ILOAD = 200 mA, ISOFT START = 1 μF × 0.07 V/μs + 200 mA = 270 mA, the current required for charging output
capacitor and supplying the load current.
If the output capacitor and load are increased such that the soft-start current exceeds the output current limit, the
current is clamped at the typical current limit of 400 mA. For example, if COUT = 10 μF and IOUT = 200 mA, 10 μF
× 0.07 V/μs + 200 mA = 900 mA is not supplied. Instead, the current is clamped at 400 mA.
14
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
Typical Application (continued)
8.2.3 Application Curves
10.00
1.00
0.10
0.01
0
100
90
80
70
60
50
40
30
20
10
0
IOUT = 10 mA
IOUT = 200 mA
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
Frequency (Hz)
IOUT = 10 mA, CIN = COUT = 1 µF
Figure 26. PSRR vs Frequency
(VIN – VOUT = 0.5 V, TPS72718)
Figure 27. Output Spectral Noise Density vs Output
Voltage (TPS72718)
200 mA
IOUT
200 mA
IOUT
1 mA
0.1 mA
VOUT
VOUT
100 ms/div
50 ms/div
VIN = 2.3 V, tR = tF = 1 µs
VIN = 2.3 V, tR = tF = 1 µs
Figure 28. Load Transient Response: 0.1 mA to 200 mA
(TPS72718)
Figure 29. Load Transient Response: 1 mA to 200 mA
(TPS72718)
200 mA
VOUT
IOUT
10 mA
2.7 V
VOUT
VIN
2.1 V
1 ms/div
50 ms/div
Slew rate = 1 V/µs, IOUT = 100 µA
VIN = 2.3 V, tR = tF = 1 µs
Figure 31. Line Transient Response (TPS72718)
Figure 30. Load Transient Response: 10 mA to 200 mA
(TPS72718)
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
15
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
Typical Application (continued)
EN
VOUT
VOUT
2.7 V
VIN
IIN
2.1 V
100 ms/div
20 ms/div
Slew rate = 1 V/µs, IOUT = 200 µA
VIN = 2.1 V, VOUT = 1.8 V, IOUT = 100 µA
Figure 32. Line Transient Response (TPS72718)
Figure 33. VIN Inrush Current (TPS72718)
EN
VIN
VOUT
VOUT
IIN
200 ms/div
20 ms/div
IOUT = 200 mA
VIN = 2.1 V, VOUT = 1.8 V, IOUT = 200 mA
Figure 35. VIN Ramp Up, Ramp Down Response
(TPS72718)
Figure 34. VIN Inrush Current (TPS72718)
16
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
8.3 Do's and Don'ts
Do place at least one 1.0-µF ceramic capacitor as close as possible to the OUT pin of the regulator.
Do not place the output capacitor more than 10 mm away from the regulator.
For DSE devices, do tie the NC pins to ground to improve thermal dissipation.
Do connect a 0.1-μF to 1.0-μF low equivalent series resistance (ESR) capacitor across the IN pin and GND input
of the regulator.
Do not exceed the absolute maximum ratings.
9 Power-Supply Recommendations
These devices are designed to operate from an input voltage supply range between 2.0 V and 5.5 V. The input
voltage range provides adequate headroom in order for the device to have a regulated output. This input supply
must be well regulated. If the input supply is noisy, additional input capacitors with low ESR can help improve the
output noise performance.
10 Layout
10.1 Layout Guidelines
10.1.1 Board Layout Recommendations to Improve PSRR and Noise Performance
To improve ac performance (such as PSRR, output noise, and transient response), TI recommends that the
board be designed with separate ground planes for VIN and VOUT, with the ground plane connected only at the
GND pin of the device. In addition, the ground connection for the output capacitor must be connected directly to
the GND pin of the device. High ESR capacitors may degrade PSRR.
10.1.2 Power Dissipation
The ability to remove heat from the die is different for each package type, presenting different considerations in
the printed circuit board (PCB) layout. The PCB area around the device that is free of other components moves
the heat from the device to the ambient air. Performance data for JEDEC low- and high-K boards are given in the
Thermal Information table. Using heavier copper increases the effectiveness in removing heat from the device.
The addition of plated through-holes to heat-dissipating layers also improves the heatsink effectiveness.
Power dissipation depends on input voltage and load conditions. Power dissipation (PD) is equal to the product of
the output current times the voltage drop across the output pass element (VIN to VOUT), as shown in Equation 3:
PD = (VIN - VOUT) ´ IOUT
(3)
10.1.3 Package Mounting
Solder pad footprint recommendations and recommended land patterns are attached to the end of this
document.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
17
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
10.2 Layout Example
10.2.1 DSE EVM Board Layout
This section provides the TPS727xxDSEEVM-406 board layout and illustrations.
Figure 36. Top Layer Assembly
Figure 37. Top Layer Routing
18
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
Layout Example (continued)
Figure 38. Bottom Layer Routing
Figure 39. Bottom Layer Assembly
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
19
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
Layout Example (continued)
10.2.2 YFF EVM Board Layout
This section provides the TPS727xxYFFEVM-407 board layout and illustrations.
Figure 40. Top Layer Assembly
Figure 41. Top Layer Routing
20
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
Layout Example (continued)
Figure 42. Bottom Layer Routing
Figure 43. Bottom Layer Assembly
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
21
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
Application report SLAA414, LDO PSRR Measurement Simplified.
Application report SLAA412, LDO Noise Demystified.
User guide SLVU323, TPS727xxYFF EVM
User guide SLVU325, TPS727xxDSE EVM
11.1.2 Device Nomenclature
Table 1. Device Nomenclature(1)
(2)
PRODUCT
VOUT
TPS727xxx yyy z
XXX is the nominal output voltage.
YYY is package designator.
Z is package tape and reel quantity (R = 3000, T = 250).
(1) For the most current package and ordering information see the Package Option Addendum at the end of this document, or visit the
device product folder at www.ti.com.
(2) Output voltages from 0.9 V to 5.0 V in 50-mV increments are available through the use of innovative factory EEPROM programming;
minimum order quantities may apply. Contact factory for details and availability.
11.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.3 Trademarks
E2E is a trademark of Texas Instruments.
Bluetooth is a registered trademark of Bluetooth SIG.
Zigbee is a registered trademark of Zigbee Alliance.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
22
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
23
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
24
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
PACKAGE OUTLINE
TPS727xxYFF
YFF0004
DSBGA - 0.625 mm max height
SCALE 13.000
DIE SIZE BALL GRID ARRAY
A
B
E
BALL A1
CORNER
D
0.625 MAX
C
SEATING PLANE
0.30
0.12
BALL TYP
0.4 TYP
B
A
D: Max = 0.82 mm, Min = 0.76 mm
E: Max = 1.19 mm, Min = 1.13 mm
SYMM
0.4
TYP
1
2
0.3
0.2
SYMM
4X
C A
0.015
B
02/2014
NanoFree Is a trademark of Texas Instruments.
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. NanoFreeTM package configuration.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
25
TPS727
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
www.ti.com
EXAMPLE BOARD LAYOUT
TPS727xxYFF
YFF0004
DSBGA - 0.625 mm max height
DIE SIZE BALL GRID ARRAY
(0.4) TYP
4
0.23 0.02
2
1
A
SYMM
(0.4) TYP
B
SYMM
LAND PATTERN EXAMPLE
SCALE:50X
0.05 MAX
0.05 MIN
( 0.23)
METAL
METAL
UNDER
MASK
(
0.23)
SOLDER MASK
OPENING
SOLDER MASK
OPENING
NON-SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
02/2014
NOTES: (continued)
4. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints.
Refer to Texas Instruments Literature No. SBVA017 (www.ti.com/lit/sbva017).
26
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
TPS727
www.ti.com
SBVS128F –JUNE 2009–REVISED DECEMBER 2015
EXAMPLE STENCIL DESIGN
TPS727xxYFF
YFF0004
DSBGA - 0.625 mm max height
DIE SIZE BALL GRID ARRAY
(0.4) TYP
4X ( 0.25)
(R0.05) TYP
1
2
A
B
SYMM
(0.4)
TYP
METAL
TYP
SYMM
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICK STENCIL
SCALE:50X
02/2014
NOTES: (continued)
5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release.
Copyright © 2009–2015, Texas Instruments Incorporated
Submit Documentation Feedback
27
PACKAGE OPTION ADDENDUM
www.ti.com
27-Aug-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
YFF
YFF
DSE
DSE
YFF
YFF
DSE
DSE
YFF
YFF
YFF
YFF
DSE
DSE
YFF
YFF
Qty
3000
250
(1)
(2)
(3)
(4/5)
(6)
TPS727105YFFR
TPS727105YFFT
TPS72710DSER
TPS72710DSET
TPS72711YFFR
TPS72711YFFT
TPS72715DSER
TPS72715DSET
TPS72715YFFR
TPS72715YFFT
TPS727185YFFR
TPS727185YFFT
TPS72718DSER
TPS72718DSET
TPS72718YFFR
TPS72718YFFT
ACTIVE
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
4
4
6
6
4
4
6
6
4
4
4
4
6
6
4
4
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
GA
GA
UR
UR
QL
QL
GS
GS
GS
GS
RW
RW
GT
GT
GT
GT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Green (RoHS
& no Sb/Br)
SNAGCU
3000
250
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
SNAGCU
SNAGCU
NIPDAUAG
NIPDAUAG
SNAGCU
SNAGCU
SNAGCU
SNAGCU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
27-Aug-2020
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
DSE
DSE
YFF
Qty
3000
250
(1)
(2)
(3)
(4/5)
(6)
TPS72719DSER
TPS72719DSET
TPS72719YFFR
TPS72719YFFT
TPS72725DSER
TPS72725DSET
TPS72727DSER
TPS72727DSET
TPS727285DSER
TPS727285DSET
TPS72728DSER
TPS72728DSET
TPS72728YFFR
TPS72728YFFT
TPS72730DSER
TPS72730DSET
TPS72730YFFR
ACTIVE
WSON
WSON
DSBGA
DSBGA
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
DSBGA
DSBGA
WSON
WSON
DSBGA
6
6
4
4
6
6
6
6
6
6
6
6
4
4
6
6
4
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
CB
CB
AA
AA
QA
QA
TS
TS
QK
QK
GU
GU
GU
GU
QB
QB
ZZ
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
YFF
Green (RoHS
& no Sb/Br)
SNAGCU
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
YFF
3000
250
Green (RoHS
& no Sb/Br)
NIPDAUAG
NIPDAUAG
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
3000
250
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
3000
250
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
YFF
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
DSE
DSE
YFF
3000
250
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
27-Aug-2020
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TPS72730YFFT
TPS72733DSER
TPS72733DSET
TPS72733YFFR
TPS72733YFFT
ACTIVE
DSBGA
WSON
WSON
DSBGA
DSBGA
YFF
4
6
6
4
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
ZZ
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DSE
3000
250
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
QC
QC
ZY
ZY
DSE
Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM
& no Sb/Br)
YFF
3000
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
YFF
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
TPS72748DSER
TPS72748YFFR
PREVIEW
ACTIVE
WSON
DSE
YFF
6
4
3000
3000
TBD
Call TI
Call TI
-40 to 125
-40 to 125
DSBGA
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
EY
EY
CA
CA
TPS72748YFFT
TPS72750YFFR
TPS72750YFFT
ACTIVE
ACTIVE
ACTIVE
DSBGA
DSBGA
DSBGA
YFF
YFF
YFF
4
4
4
250
3000
250
Green (RoHS
& no Sb/Br)
SNAGCU
SNAGCU
SNAGCU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com
27-Aug-2020
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
1-Feb-2018
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS727105YFFR
TPS727105YFFT
TPS72710DSER
TPS72710DSER
TPS72710DSET
TPS72710DSET
TPS72711YFFR
TPS72711YFFT
TPS72715DSER
TPS72715DSET
TPS72715YFFR
TPS72715YFFT
TPS727185YFFR
TPS727185YFFT
TPS72718DSER
TPS72718DSET
TPS72718YFFR
TPS72718YFFT
DSBGA
DSBGA
WSON
WSON
WSON
WSON
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
YFF
YFF
DSE
DSE
DSE
DSE
YFF
YFF
DSE
DSE
YFF
YFF
YFF
YFF
DSE
DSE
YFF
YFF
4
4
6
6
6
6
4
4
6
6
4
4
4
4
6
6
4
4
3000
250
180.0
180.0
179.0
178.0
178.0
179.0
180.0
180.0
179.0
179.0
180.0
180.0
180.0
180.0
178.0
178.0
180.0
180.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
0.89
0.89
1.8
1.26
1.26
1.8
0.69
0.69
1.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q1
Q1
Q2
Q2
Q2
Q2
Q1
Q1
Q2
Q2
Q2
Q2
Q1
Q1
Q2
Q2
Q2
Q2
3000
3000
250
1.7
1.7
0.95
0.95
1.0
1.7
1.7
250
1.8
1.8
3000
250
0.89
0.89
1.8
1.26
1.26
1.8
0.69
0.69
1.0
3000
250
1.8
1.8
1.0
3000
250
0.89
0.89
0.89
0.89
1.7
1.26
1.26
1.26
1.26
1.7
0.69
0.69
0.69
0.69
0.95
0.95
0.69
0.69
3000
250
3000
250
1.7
1.7
3000
250
0.89
0.89
1.26
1.26
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
1-Feb-2018
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS72719DSER
TPS72719DSER
TPS72719DSET
TPS72719DSET
TPS72719YFFR
TPS72719YFFT
TPS72725DSER
TPS72725DSET
TPS72727DSER
TPS72727DSER
TPS72727DSET
TPS72727DSET
TPS727285DSER
TPS727285DSER
TPS727285DSET
TPS727285DSET
TPS72728DSER
TPS72728DSER
TPS72728DSET
TPS72728DSET
TPS72728YFFR
TPS72728YFFT
TPS72730DSER
TPS72730DSET
TPS72730YFFR
TPS72730YFFT
TPS72733DSER
TPS72733DSET
TPS72733YFFR
TPS72733YFFT
TPS72748YFFR
TPS72748YFFT
TPS72750YFFR
TPS72750YFFT
WSON
WSON
WSON
WSON
DSBGA
DSBGA
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSE
DSE
DSE
DSE
YFF
YFF
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
YFF
YFF
DSE
DSE
YFF
YFF
DSE
DSE
YFF
YFF
YFF
YFF
YFF
YFF
6
6
6
6
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
6
6
4
4
6
6
4
4
4
4
4
4
3000
3000
250
178.0
179.0
178.0
179.0
180.0
180.0
179.0
179.0
179.0
178.0
179.0
178.0
178.0
179.0
179.0
178.0
178.0
179.0
179.0
178.0
180.0
180.0
178.0
178.0
180.0
180.0
178.0
178.0
180.0
180.0
180.0
180.0
180.0
180.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
1.7
1.8
1.7
1.8
0.95
1.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q2
Q2
Q2
Q2
Q1
Q1
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q1
Q1
Q2
Q2
Q1
Q1
Q2
Q2
Q1
Q1
1.7
1.7
0.95
1.0
250
1.8
1.8
3000
250
0.89
0.89
1.8
1.26
1.26
1.8
0.69
0.69
1.0
3000
250
1.8
1.8
1.0
3000
3000
250
1.8
1.8
1.0
1.7
1.7
0.95
1.0
1.8
1.8
250
1.7
1.7
0.95
0.95
1.0
3000
3000
250
1.7
1.7
1.8
1.8
1.8
1.8
1.0
250
1.7
1.7
0.95
0.95
1.0
3000
3000
250
1.7
1.7
1.8
1.8
1.8
1.8
1.0
250
1.7
1.7
0.95
0.69
0.69
0.95
0.95
0.69
0.69
0.95
0.95
0.69
0.69
0.69
0.69
0.69
0.69
3000
250
0.89
0.89
1.7
1.26
1.26
1.7
3000
250
1.7
1.7
3000
250
0.89
0.89
1.7
1.26
1.26
1.7
3000
250
1.7
1.7
3000
250
0.89
0.89
0.89
0.89
0.89
0.89
1.26
1.26
1.26
1.26
1.26
1.26
3000
250
3000
250
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
1-Feb-2018
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS727105YFFR
TPS727105YFFT
TPS72710DSER
TPS72710DSER
TPS72710DSET
TPS72710DSET
TPS72711YFFR
TPS72711YFFT
TPS72715DSER
TPS72715DSET
TPS72715YFFR
TPS72715YFFT
TPS727185YFFR
TPS727185YFFT
TPS72718DSER
TPS72718DSET
TPS72718YFFR
TPS72718YFFT
TPS72719DSER
TPS72719DSER
DSBGA
DSBGA
WSON
WSON
WSON
WSON
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
WSON
WSON
YFF
YFF
DSE
DSE
DSE
DSE
YFF
YFF
DSE
DSE
YFF
YFF
YFF
YFF
DSE
DSE
YFF
YFF
DSE
DSE
4
4
6
6
6
6
4
4
6
6
4
4
4
4
6
6
4
4
6
6
3000
250
182.0
182.0
203.0
205.0
205.0
203.0
182.0
182.0
203.0
203.0
182.0
182.0
182.0
182.0
205.0
205.0
182.0
182.0
205.0
203.0
182.0
182.0
203.0
200.0
200.0
203.0
182.0
182.0
203.0
203.0
182.0
182.0
182.0
182.0
200.0
200.0
182.0
182.0
200.0
203.0
20.0
20.0
35.0
33.0
33.0
35.0
20.0
20.0
35.0
35.0
20.0
20.0
20.0
20.0
33.0
33.0
20.0
20.0
33.0
35.0
3000
3000
250
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
3000
Pack Materials-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
1-Feb-2018
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS72719DSET
TPS72719DSET
TPS72719YFFR
TPS72719YFFT
TPS72725DSER
TPS72725DSET
TPS72727DSER
TPS72727DSER
TPS72727DSET
TPS72727DSET
TPS727285DSER
TPS727285DSER
TPS727285DSET
TPS727285DSET
TPS72728DSER
TPS72728DSER
TPS72728DSET
TPS72728DSET
TPS72728YFFR
TPS72728YFFT
TPS72730DSER
TPS72730DSET
TPS72730YFFR
TPS72730YFFT
TPS72733DSER
TPS72733DSET
TPS72733YFFR
TPS72733YFFT
TPS72748YFFR
TPS72748YFFT
TPS72750YFFR
TPS72750YFFT
WSON
WSON
DSBGA
DSBGA
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
WSON
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
WSON
WSON
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSE
DSE
YFF
YFF
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
DSE
YFF
YFF
DSE
DSE
YFF
YFF
DSE
DSE
YFF
YFF
YFF
YFF
YFF
YFF
6
6
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
4
4
6
6
4
4
6
6
4
4
4
4
4
4
250
250
205.0
203.0
182.0
182.0
203.0
203.0
203.0
205.0
203.0
205.0
205.0
203.0
203.0
205.0
205.0
203.0
203.0
205.0
182.0
182.0
205.0
205.0
182.0
182.0
205.0
205.0
182.0
182.0
182.0
182.0
182.0
182.0
200.0
203.0
182.0
182.0
203.0
203.0
203.0
200.0
203.0
200.0
200.0
203.0
203.0
200.0
200.0
203.0
203.0
200.0
182.0
182.0
200.0
200.0
182.0
182.0
200.0
200.0
182.0
182.0
182.0
182.0
182.0
182.0
33.0
35.0
20.0
20.0
35.0
35.0
35.0
33.0
35.0
33.0
33.0
35.0
35.0
33.0
33.0
35.0
35.0
33.0
20.0
20.0
33.0
33.0
20.0
20.0
33.0
33.0
20.0
20.0
20.0
20.0
20.0
20.0
3000
250
3000
250
3000
3000
250
250
3000
3000
250
250
3000
3000
250
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
3000
250
Pack Materials-Page 4
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
相关型号:
TPS728120150DRVR
200mA Low-Dropout Linear Regulator with Pin-Selectable Dual-Voltage Level Output
TI
TPS728120150DRVT
200mA Low-Dropout Linear Regulator with Pin-Selectable Dual-Voltage Level Output
TI
TPS728175295YZUR
200mA Low-Dropout Linear Regulator with Pin-Selectable Dual-Voltage Level Output
TI
TPS728175295YZUT
200mA Low-Dropout Linear Regulator with Pin-Selectable Dual-Voltage Level Output
TI
©2020 ICPDF网 联系我们和版权申明