TPS72215DBVRG4 [TI]
1.5V FIXED POSITIVE LDO REGULATOR, PDSO5, GREEN, PLASTIC, SOT-23, 5 PIN;型号: | TPS72215DBVRG4 |
厂家: | TEXAS INSTRUMENTS |
描述: | 1.5V FIXED POSITIVE LDO REGULATOR, PDSO5, GREEN, PLASTIC, SOT-23, 5 PIN 光电二极管 输出元件 调节器 |
文件: | 总18页 (文件大小:973K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS72201,TPS72215
TPS72216,TPS72218
Actual Size
(3,00 mm x 3,00 mm)
www.ti.com
SLVS390B – DECEMBER 2001 – REVISED MAY 2002
LOW INPUT VOLTAGE, CAP FREE 50-mA
LOW-DROPOUT LINEAR REGULATORS
many other regulators that require 2.5-V or higher input
FEATURES
voltages for operation, these regulators can be
operated directly from two AAA batteries. Also, the
typical quiescent current (ground pin current) is low,
starting at 85 µA during normal operation and 1 µA in
shutdown mode. Thus, these regulators can be
operated very efficiently and, in a battery-powered
application, help extend the longevity of the device.
D
50-mA LDO
D
Available in 1.5-V, 1.6-V, and 1.8-V
Fixed-Output and Adjustable Versions
D
D
D
D
D
D
D
Low Input Voltage Requirement
(Down to 1.8 V)
Small Output Capacitor, 0.1-µF
Similar LDO regulators require 1-µF or larger output
capacitors for stability. However, this regulator uses an
internal compensation scheme that stabilizes the
feedback loop over the full range of input voltages and
load currents with output capacitances as low as
0.1-µF. Ceramic capacitors of this size are relatively
inexpensive and available in small footprints.
Dropout Voltage Typically 50 mV at 50 mA
Less Than 1 µA Quiescent Current in
Shutdown Mode
Thermal Protection
Over Current Limitation
5-Pin SOT-23 (DBV) Package
This family of regulators is particularly suited as a
portable power supply solution due to its minimal board
space requirement and 1.8-V minimum input voltage.
Being able to use two off-the-shelf, AAA, batteries
makes system design easier and also reduces
component cost. Moreover, the solution will be more
efficient than if a regulator with a higher input voltage is
used.
APPLICATIONS
D
D
D
D
D
D
D
D
D
Portable Communication Devices
Battery Powered Equipment
PCMCIA Cards
Personal Digital Assistants
Modems
Bar Code Scanners
Backup Power Supplies
SMPS Post Regulation
Internet Audio
DBV PACKAGE
(TOP VIEW)
1
OUT
5
IN
GND
EN
2
3
DESCRIPTION
4
NC/FB
The TPS722xx family of LDO regulators is available in
fixed voltage options that are commonly used to power
the latest DSP’sandmicrocontrollerswithanadjustable
option ranging from 1.22 V to 2.5 V. These regulators
can be used in a wide variety of applications ranging
from portable, battery-powered equipment to PC
peripherals. The family features operation over a wide
range of input voltages (1.8 V to 5.5 V) and low dropout
voltage (50 mV at full load). Therefore, compared to
TPS72215
OUT
1.8 V
1.5 V
IN
EN GND
0.1 µF
0.1 µF
Pleasebe aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Products
conform to specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all parameters.
Copyright 2002, Texas Instruments Incorporated
TPS72201,TPS72215
TPS72216,TPS72218
www.ti.com
SLVS390B – DECEMBER 2001 – REVISED MAY 2002
Thesedeviceshavelimitedbuilt-inESDprotection.Theleadsshouldbeshortedtogetherorthedeviceplacedinconductivefoamduring
storageor handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
T
VOLTAGE
Adjustable
1.5 V
PACKAGE
PART NUMBER
(1)
SYMBOL
PELI
J
(2)
TPS72201DBVR
TPS72201DBVT
(1)
TPS72215DBVT
(2)
TPS72215DBVR
PENI
SOT-23
(DBV)
–40°C to 125°C
(1)
(2)
TPS72216DBVR
1.6 V
TPS72216DBVT
(1)
PHGI
(2)
TPS72218DBVR
1.8 V
TPS72218DBVT
PEMI
(1)
(2)
The DBVT indicates tape and reel of 250 parts.
The DBVR indicates tape and reel of 3000 parts.
ABSOLUTE MAXIMUM RATINGS
overoperating free-air temperature range unless otherwise noted
(1)
TPS72201,TPS72215
TPS72216,TPS72218
ꢀ
ꢁ
ꢂ
Input voltage range
–0.3 V to 7 V
–0.3 V to 7 V
Voltage range at EN
Voltage on OUT, FB, NC
Peak output current
–0.3 V to V + 0.3 V
I
Internallylimited
3 kV
ESD rating, HBM
Continuoustotalpowerdissipation
See Dissipation Rating Table
–40°C to 150°C
–65°C to 150°C
Operating virtual junction temperature range, T
J
Storage temperature range, T
stg
(1)
Stressesbeyondthoselistedunder“absolutemaximumratings”maycausepermanentdamagetothedevice.Thesearestressratingsonly,and
functionaloperation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network ground terminal.
(2)
PACKAGE DISSIPATION RATING
DERATING FACTOR
T
≤ 25°C
T
= 70°C
T = 85°C
A
A
A
BOARD
PACKAGE
R
θJC
R
θJA
ABOVE T = 25°C
POWER RATING POWER RATING POWER RATING
A
(1)
Low K
DBV
DBV
65.8 °C/W
65.8 °C/W
259 °C/W
180 °C/W
3.9 mW/°C
5.6 mW/°C
386 mW
555 mW
212 mW
305 mW
154 mW
222 mW
(2)
High K
(1)
(2)
TheJEDECLowK(1s)boarddesignusedtoderivethisdatawasa3inchx3inch,two-layerboardwith2ouncecoppertracesontopoftheboard.
TheJEDEC High K (2s2p) board design used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power andground
planesand 2 ounce copper traces on top and bottom of the board.
2
TPS72201,TPS72215
TPS72216,TPS72218
www.ti.com
SLVS390B – DECEMBER 2001 – REVISED MAY 2002
ELECTRICAL CHARACTERISTICS
overrecommended operating free-air temperature range, V = V
I
+ 1 V, I = 1 mA, EN = V , C = 4.7 µF (unless otherwise noted)
O I o
O(typ)
PARAMETER
TEST CONDITIONS
MIN
1.8
0
TYP
MAX
5.5
UNIT
V
(1)
Inputvoltage
V
I
I
O
Continuousoutputcurrent
50
mA
°C
T
J
Operatingjunctiontemperature
–40
125
(1)
TPS72201 0 µA< I < 50 mA,
1.2 V ≤ V ≤ 2.5 V 0.97 V
1.03 V
O
O
O
1.455
1.552
1.746
O
T
= 25°C
1.5
1.6
J
TPS72215
TPS72216
TPS72218
0 µA< I < 50 mA
2.5 V ≤ V ≤ 5.5 V
1.545
O
I
T
J
= 25°C
V
O
Outputvoltage
V
0 µA< I < 50 mA
2.6 V ≤ V ≤ 5.5 V
1.648
1.854
120
550
1
O
I
T
J
= 25°C
1.8
0 µA< I < 50 mA
2.5 V ≤ V ≤ 5.5 V
I
O
T
J
= 25°C
85
Quiescent current (GND terminal
current)
I
µA
µA
(Q)
I
I
= 50 mA
= 50 mA
T
T
= 25°C
= 25°C
275
0.01
O
J
O
EN < 0.5 V,
EN < 0.5 V
J
Standbycurrent
BW = 200 Hz to 100 kHz,
V
Output noise voltage
Referencevoltage
Ripplerejection
TPS72215
C
= 1 µF
90
1.225
48
µV
V
n
o
T
= 25°C
J
J
V
ref
T
= 25°C
f = 100 Hz,
= 50 mA
C
o
= 10 µF,
T
J
= 25°C,
dB
mA
PSRR
I
See Note 1
O
Currentlimit
See Note 2
175
525
0.09
0.1
T
= 25°C
= 25°C
0.03
0.2
Outputvoltagelineregulation
J
J
V
O
+ 1 V < V ≤ 5.5 V
%/V
mV
I
(3)
)
(∆V /V
O
O
Output voltage load
regulation
TPS72218 0 < I < 50 mA,
O
T
V
V
EN high level input
EN low level input
1.4
V
V
IH
–0.2
0.4
IL
EN = 0 V
EN = IN
–0.01
–0.01
50
I
EN input current
µA
I
TPS72218
TPS72201
TPS72201
I
= 50 mA
= 50 mA
T
= 25°C
O
O
J
(4)
V
Dropout voltage
mV
DO
I
1.2 V ≤ V ≤ 5.2 V
100
1
O
I
n
Feedback input current
µA
°C
°C
Thermalshutdowntemperature
Thermalshutdownhysteresis
170
20
(1)
(2)
(3)
Minimum IN operating voltage is 1.8 V or V
+ V
(max load), whichever is greater.
DO
O(max)
Test condition includes, output voltage V = 1 V and pulse duration = 10 mS.
O
V
Imax
= 5.5 V, V
= (V + 1) or 1.8 V whichever is greater.
Imin O
Oǒ5.5 V * VIminǓ
V
ǒ
Ǔ
Line regulation (mV) + %ńV
1000
100
(4)
Dropoutvoltage is defined as the differentialvoltagebetweenV and V when V drops 100 mV below the value measured with V = V + 1 V.
O
I
O
I
O
3
TPS72201,TPS72215
TPS72216,TPS72218
www.ti.com
SLVS390B – DECEMBER 2001 – REVISED MAY 2002
FUNCTIONAL BLOCK DIAGRAM—ADJUSTABLE VERSION
TPS72201
OUT
FB
IN
EN
Current Limit
/ Thermal
Protection
V
ref
GND
FUNCTIONAL BLOCK DIAGRAM—FIXED VERSION
TPS72215/16/18
OUT
IN
EN
Current Limit
/ Thermal
Protection
V
ref
GND
NC (see Note 1)
(1) This pin must be left floating and not connected to GND
Terminal Functions
TERMINAL
NAME
I/O
DESCRIPTION
NO.
2
GND
EN
Ground
3
I
I
Enableinput
Input supply voltage
IN
1
NC/FB
OUT
4
I
NC = Not connected (see Note 6); FB = Feedback (adjustable option TPS72201)
Regulatedoutputvoltage
5
O
4
TPS72201,TPS72215
TPS72216,TPS72218
www.ti.com
SLVS390B – DECEMBER 2001 – REVISED MAY 2002
TYPICAL CHARACTERISTICS
TPS72218
GROUND CURRENT
vs
TPS72218
TPS72218
OUTPUT VOLTAGE
vs
OUTPUT VOLTAGE
vs
JUNCTION TEMPERATURE
OUTPUT CURRENT
JUNCTION TEMPERATURE
1.8020
300
1.8002
1.8001
1.8000
1.7999
V
= 2.8 V
I
V
= 2.8 V
= 1 µF
= 25° C
I
I
= 50 mA
C
o
= 1 µF
O
C
o
J
1.8000
1.7980
1.7960
1.7940
1.7920
1.7900
250
200
T
I
= 1 mA
O
I
= 50 mA
O
150
100
I
= 10 mA
O
1.7998
50
0
1.7997
1.7996
V
= 2.8 V
I
C
o
= 1 µF
–40 –25 –10
5
20 35 50 65 80 95 110 125
–40 –25 –10 5 20 35 50 65 80 95 110 125
0
10
20
30
40
50
T
J
– Junction Temperature – °C
T
J
– Junction Temperature – °C
I
– Output Current – mA
O
Figure 1
Figure 2
Figure 3
TPS72218
TPS72218
TPS72218
GROUND CURRENT
vs
OUTPUT CURRENT
OUTPUT IMPEDANCE
vs
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
FREQUENCY
300
250
200
1 k
2.5
V
C
= 2.8 V
V
C
= 2.8 V
V
C
= 2.8 V
I
I
I
T
J
= 125° C
= 1 µF
= 1 µF
= 1 µF
o
o
o
100
10
2
I
= 1 mA
O
1.5
150
100
1
0.1
T
= 25° C
J
1
I
= 50 mA
O
T
J
= –40° C
I
= 50 mA
O
0.5
50
0
0.01
0.001
0
0
5
10 15 20 25 30 35 40 45 50
100
1 k
10 k
100 k
1
10 100 1 k 10 k 100 k 1 M 10 M
I
– Output Current – mA
f – Frequency – Hz
f – Frequency – Hz
O
Figure 5
Figure 4
Figure 6
TPS72118
TPS72218
TPS72218
POWER SUPPLY RIPPLE REJECTION
vs
OUTPUT VOLTAGE, ENABLE VOLTAGE
DROPOUT VOLTAGE
vs
vs
FREQUENCY
TIME (START-UP)
JUNCTION TEMPERATURE
70
80
70
60
50
40
30
20
10
V
= 2.8 V
V
C
= 2.8 V
= 1 µF
= 50 mA
I
V
I
o
EN
3
2
C
o
= 1 µF
60
50
40
I
O
1
0
I
= 50 mA
O
30
20
10
0
2
V
V
I
= 2.8 V
I
1
0
= 1.8 V
O
I
= 10 mA
V
O
O
= 50 mA
O
C
o
= 1 µF
0
–40 –25 –10 5 20 35 50 65 80 95 110 125
1
10
100
1 k
10 k 100 k 1 M
0
50 100 150 200 200 300 350 400 450 500
f – Frequency – Hz
T
J
– Junction Temperature – °C
t – Time – µs
Figure 7
Figure 8
Figure 9
5
TPS72201,TPS72215
TPS72216,TPS72218
www.ti.com
SLVS390B – DECEMBER 2001 – REVISED MAY 2002
TYPICAL CHARACTERISTICS
TPS72218
TPS72218
LINE TRANSIENT RESPONSE
POWER UP / POWER DOWN
LOAD TRANSIENT RESPONSE
6
5
4
3
2
I
C
= 50 mA
= 1 µF
O
o
V
C
= 2.8 V
I
= 1 µF
o
V
V
I
I
3.8
2.8
50
0
dI
O
dt
0µ.1sA
+
dV
I
dt
0µ.4sV
V
+
O
1
0
1
0
100
0
V
O
C
= 1 µF
o
i
C = 1 µF
R
L
= 36 Ω
-1
–100
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
0
10 20 30 40 50 60 70 80 90 100
t – Time – ms
0
50 100 150 200 250 300 350 400 450 500
t – Time – µs
t – Time – ms
Figure 12
Figure 11
Figure 10
TPS72201
DROPOUT VOLTAGE
vs
DC DROPOUT VOLTAGE
vs
OUTPUT CURRENT
MINIMUMREQUIRED INPUT VOLTAGE
vs
INPUT VOLTAGE
OUTPUT VOLTAGE
80
70
60
50
40
30
20
10
0
80
70
60
50
40
30
20
10
0
5.5
I
= 50 mA
O
I
= 50 mA
O
5
4.5
T
J
= 125°C
T = 125°C
J
4
T
J
= 125°C
T
J
= 25°C
T
J
= 25°C
3.5
T
J
= 25°C
3
2.5
T
J
= –40°C
T
J
= –40°C
2
T
J
= –55°C
1.5
1
0
5
10 15 20 25 30 35 40 45 50
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
1.8
2.5
3.3
4.0
4.8
5.5
I
– Output Current – mA
V – Input Voltage – V
I
O
V
– Output Voltage – V
O
Figure 14
Figure 13
Figure 15
6
TPS72201,TPS72215
TPS72216,TPS72218
www.ti.com
SLVS390B – DECEMBER 2001 – REVISED MAY 2002
APPLICATION INFORMATION
TheTPS722xxfamilyoflow-dropout(LDO)regulatorsfunctionswithaverylowinputvoltage(>1.8V). Thedropoutvoltage
is typically 50 mV at full load. Typicalquiescentcurrent(groundpincurrent)isonly85 µA and drops to 1 µA in the shutdown
mode.
DEVICE OPERATION
TheTPS722xx family can be operated at low input voltages due to low voltage circuit design techniques and a PMOS pass
element that exhibits low dropout.
A logic low on the enable input, EN, shuts off the output and reduces the supply current to less than 1 µA. EN may be tied
to V in applications where the shutdown feature is not used.
IN
Currentlimiting and thermal protection prevent damage by excessive output current and/or power dissipation. The device
switches into a constant-current mode at approximately 350 mA; further load reduces the output voltage instead of
increasingthe output current. The thermal protection shuts the regulator off if the junction temperature rises above 170°C.
Recoveryisautomaticwhenthejunctiontemperaturedropsapproximately20°Cbelowthehightemperaturetrippoint. The
PMOS pass element includes a back diode that safely conducts reverse current when the input voltage level drops below
the output voltage level.
A typical application circuit is shown in Figure 16.
TPS722xx
1
V
I
IN
5
4
V
O
OUT
0.1 µF
NC
3
EN
+
0.1 µF
GND
2
Figure 16. Typical Application Circuit
DUAL SUPPLY APPLICATION
In portable, battery-powered electronics, separate power rails for the DSP or microcontroller core voltage (V
) and I/O
CORE
peripherals (V ) are usually necessary. The TPS721xx family of LDO linear regulators is ideal for providing V
for
IO
(CORE)
the DSP or microcontroller. As shown in Figure 17, two AAA batteries provide an input voltage to a boost converter and
the TPS72115 LDO linear regulator. The batteries combine input voltage ranges from 3.0 V down to 1.8 V near the end
oftheirusefullives.Therefore,aboostconverterisnecessarytoprovidethetypical3.3VneededforV ,andtheTPS72115
IO
linear regulator provides a regulated V
voltage, which in this example is 1.5 V. Although there is no explicit circuitry
(CORE)
to perform power-up sequencing of first V
then V , the output of the linear regulator reaches its regulated voltage
(CORE)
IO
muchfaster (<400 µs) than the output of any switching type boost converter due to the inherent slow start up of those types
of converters. Assuming a boost converter with minimum V of 1.8 V is appropriately chosen, this power supply solution
I
can be used over the entire life of the two off-the-shelf AAA batteries. Thus, this solution is very efficient and the design
time and overall cost of the solution is minimized.
7
TPS72201,TPS72215
TPS72216,TPS72218
www.ti.com
SLVS390B – DECEMBER 2001 – REVISED MAY 2002
3.3 V
1.5 V
1.8 V – 3 V
BoostConverter
V
IO
DSP or
Controller
1.8 V
TPS72215
V
CORE
Two AAA
Batteries
Figure 17. Dual Supply Application Circuit
EXTERNAL CAPACITOR REQUIREMENTS
A0.1-µFceramicbypasscapacitorisrequiredonboththeinputandoutputforstability. Largercapacitorsimprovetransient
response, noise rejection, and ripple rejection. A higher value electrolytic input capacitor may be necessary if large, fast
risetimeloadtransientareanticipated, and/orthereissignificantinputresistancefromthedevicetotheinputpowersupply.
POWER DISSIPATION AND JUNCTION TEMPERATURE
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature allowable
without damaging the device is 150°C. This restriction limits the power dissipation the regulator can handle in any given
application. To ensure the junction temperature is within acceptable limits, calculate the maximum allowable dissipation,
P
, and the actual dissipation, P , which must be less than or equal to P
.
D(max)
D
D(max)
The maximum-power-dissipation limit is determined using the following equation:
T max * T
J
A
P
+
D(max)
R
qJA
Where:
T max is the maximum allowable junction temperature.
J
R
table.
is the thermal resistance junction-to-ambient for the package, see the power dissipation rating
θJA
T is the ambient temperature.
A
The regulator dissipation is calculated using:
+ ǒVI * V
Ǔ
P
I
D
O
O
Power dissipation resulting from quiescent current is negligible.
8
TPS72201,TPS72215
TPS72216,TPS72218
www.ti.com
SLVS390B – DECEMBER 2001 – REVISED MAY 2002
PROGRAMMING THE TPS72201 ADJUSTABLE LDO REGULATOR
The output voltage of the TPS72201 adjustable regulator is programmed using an external resistor divider as shown in
Figure 18. The output voltage is calculated using:
R1
R2
ǒ1 ) Ǔ
(1)
V
+ V
O
ref
Where:
V
= 1.225 V typ (the internal reference voltage)
ref
ResistorsR1andR2shouldbechosenforapproximately10-µAdividercurrent. Lowervalueresistorscanbeusedbutoffer
no inherent advantage and waste more power. Higher values should be avoided, as leakage currents at FB increase the
output
voltage
error.
The
recommended
design
procedure
is
to
choose
R2 = 121 kΩ to set the divider current at 10 µA and then calculate R1 using:
V
O
R1 +
* 1 R2
ǒ Ǔ
(2)
V
ref
Where:
V
= 1.225
ref
TPS72201
OUTPUT VOLTAGE
PROGRAMMING GUIDE
DIVIDER RESISTANCE
1
V
I
IN
OUTPUT
†
(kΩ)
VOLTAGE
(V)
0.1 µF
≥1.7 V
5
R1
R2
V
O
OUT
FB
2.5
3.3
127
205
121
121
3
R1
EN
4
≤0.9 V
†
1% values shown.
0.1 µF
GND
2
R2
Figure 18. TPS72201 Adjustable LDO Regulator Programming
REGULATOR PROTECTION
The TPS722xx pass element has a built-in back diode that safely conducts reverse current when the input voltage drops
below the output voltage (e.g., during power down). Current is conducted from the output to the input and is not internally
limited. If extended reverse voltage is anticipated, external limiting might be appropriate.
TheTPS722xx also features internal current limiting and thermalprotection. Duringnormaloperation, theTPS722xxlimits
output current to approximately 350 mA. When current limiting engages, the output voltage scales back linearly until the
overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be taken not to
exceed the power dissipation ratings of the package. If the temperature of the device exceeds 170°C,thermal-protection
circuitry shuts it down. Once the device has cooled down to below 150°C, regulator operation resumes.
9
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
PACKAGING INFORMATION
Orderable Device
TPS72201DBVR
TPS72201DBVRG4
TPS72201DBVT
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
DBV
5
5
5
5
5
5
5
5
5
5
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
PELI
PELI
PELI
PELI
PENI
PENI
PEMI
PEMI
PEMI
PEMI
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS72201DBVTG4
TPS72215DBVT
250
Green (RoHS
& no Sb/Br)
250
Green (RoHS
& no Sb/Br)
TPS72215DBVTG4
TPS72218DBVR
TPS72218DBVRG4
TPS72218DBVT
250
Green (RoHS
& no Sb/Br)
3000
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS72218DBVTG4
250
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Jan-2018
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS72201DBVR
TPS72201DBVT
TPS72215DBVT
TPS72218DBVR
TPS72218DBVT
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
DBV
5
5
5
5
5
3000
250
178.0
178.0
178.0
178.0
178.0
9.0
9.0
9.0
9.0
9.0
3.23
3.23
3.23
3.23
3.3
3.17
3.17
3.17
3.17
3.2
1.37
1.37
1.37
1.37
1.4
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q3
Q3
250
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Jan-2018
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS72201DBVR
TPS72201DBVT
TPS72215DBVT
TPS72218DBVR
TPS72218DBVT
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
DBV
5
5
5
5
5
3000
250
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
18.0
18.0
18.0
18.0
18.0
250
3000
250
Pack Materials-Page 2
PACKAGE OUTLINE
DBV0005A
SOT-23 - 1.45 mm max height
S
C
A
L
E
4
.
0
0
0
SMALL OUTLINE TRANSISTOR
C
3.0
2.6
0.1 C
1.75
1.45
B
1.45 MAX
A
PIN 1
INDEX AREA
1
2
5
2X 0.95
1.9
3.05
2.75
1.9
4
3
0.5
5X
0.3
0.15
0.00
(1.1)
TYP
0.2
C A B
0.25
GAGE PLANE
0.22
0.08
TYP
8
0
TYP
0.6
0.3
TYP
SEATING PLANE
4214839/C 04/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Refernce JEDEC MO-178.
www.ti.com
EXAMPLE BOARD LAYOUT
DBV0005A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
5X (1.1)
1
5
5X (0.6)
SYMM
(1.9)
2
3
2X (0.95)
4
(R0.05) TYP
(2.6)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214839/C 04/2017
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DBV0005A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
5X (1.1)
1
5
5X (0.6)
SYMM
(1.9)
2
3
2X(0.95)
4
(R0.05) TYP
(2.6)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
4214839/C 04/2017
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
相关型号:
TPS72216DBVTG4
50-mA, Cap Free, Low Input Voltage, Low-Dropout Linear Regulator 5-SOT-23 -40 to 125
TI
©2020 ICPDF网 联系我们和版权申明