TPS63901YCJR [TI]
具有纳安级 Iq 的 400mA 降压/升压转换器 | YCJ | 12 | -40 to 125;型号: | TPS63901YCJR |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有纳安级 Iq 的 400mA 降压/升压转换器 | YCJ | 12 | -40 to 125 升压转换器 |
文件: | 总33页 (文件大小:3912K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS63901
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
TPS63901 采用WCSP 封装、具有输入电流限制和DVS 的1.8V 至5.5V、75nA IQ
降压/升压转换器
1 特性
3 说明
• 输入电压范围为1.8V 至5.5V
• 1.8V 至5V 输出电压范围(100mV 阶跃)
– 可使用外部电阻器进行编程
TPS63901 器件是一款具有超低静态电流(典型值为
75nA)的高效同步降压/升压转换器。该器件具有 32
个用户可编程的输出电压设置,范围为1.8V 至5V。
– SEL 引脚用于在两个输出电压预设之间切换
• VI ≥2.0V、VO = 3.3V 时,输出电流大于400mA
– 可堆叠:并联多个器件以获得更高的输出电流
• 负载电流为10µA 时,效率> 90%
– 静态电流为75nA
– 60nA 关断电流
• 单模式运行
动态电压调节特性使各项应用可于运行期间在两个输出
电压之间进行切换;例如,在待机运行期间,可通过降
低系统电源电压来降低功耗。
凭借其宽电源电压范围和可编程的输入电流限制
(1mA 至 100mA 和无限制),该器件非常适合与 3
芯串联碱性电池、1 芯锂二氧化锰 (Li-MnO2) 或1 芯锂
亚硫酰氯 (Li-SOCl2) 等各种一次电池以及二次电池搭
配使用。
– 无需在降压、降压/升压和升压模式之间转换
– 低输出波纹
– 出色的瞬态性能
高输出电流功能支持 sub-1GHz、BLE、LoRa、wM-
Bus 和NB-IoT 等常用射频标准。
• 可靠运行的特性
– 集成软启动
器件信息
– 可编程输入电流限制,具有八个设置(1mA 至
100mA 和无限制)
– 输出短路和过热保护
器件型号(1)
封装尺寸(标称值)
封装
TPS63901
WCSP (12)
1.50 mm × 1.15 mm
• 微型解决方案尺寸
(1) 如需了解所有可用封装,请参阅数据表末尾的可订购产品附
录。
– 小型2.2µH 电感器,单个22µF 输出电容器
– 12 焊球、1.5mm × 1.15mm、0.35mm 间距
WCSP 封装
L1
LX1
LX2
2 应用
VO
3.3 V, 400 mA
1.8 V to 5.5 V
VIN
VOUT
• 智能手表
• 智能追踪器
• 可穿戴电子产品
10 µF
22 µF
• 医疗传感器贴片和患者监护仪
• 智能仪表和传感器节点
• 电子智能锁
CFG1
CFG2
CFG3
36.5 kΩ
To/from
system
EN
SEL
GND
• 工业物联网(智能传感器)和窄带物联网
简化版原理图
本文档旨在为方便起见,提供有关TI 产品中文版本的信息,以确认产品的概要。有关适用的官方英文版本的最新信息,请访问
www.ti.com,其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SLVSGC1
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
Table of Contents
8 Application and Implementation..................................19
8.1 Application Information............................................. 19
8.2 Typical Application.................................................... 19
9 Power Supply Recommendations................................27
10 Layout...........................................................................27
10.1 Layout Guidelines................................................... 27
10.2 Layout Example...................................................... 27
11 Device and Documentation Support..........................28
11.1 Device Support........................................................28
11.2 Documentation Support.......................................... 28
11.3 接收文档更新通知................................................... 28
11.4 支持资源..................................................................28
11.5 Trademarks............................................................. 28
11.6 Electrostatic Discharge Caution..............................28
11.7 术语表..................................................................... 28
12 Mechanical, Packaging, and Orderable
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings........................................ 4
6.2 ESD Ratings............................................................... 4
6.3 Recommended Operating Conditions.........................4
6.4 Thermal Information....................................................4
6.5 Electrical Characteristics.............................................5
6.6 Typical Characteristics................................................7
7 Detailed Description........................................................8
7.1 Overview.....................................................................8
7.2 Functional Block Diagram...........................................8
7.3 Feature Description.....................................................8
7.4 Device Functional Modes..........................................17
Information.................................................................... 28
4 Revision History
注:以前版本的页码可能与当前版本的页码不同
Changes from Revision * (December 2021) to Revision A (June 2022)
Page
• 将文档状态从“预告信息”更改为“量产数据”................................................................................................ 1
Copyright © 2022 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
5 Pin Configuration and Functions
LX1
GND
GND
LX2
EN
A1
B1
C1
D1
A3
B3
C3
D3
VIN
A2
B2
C2
D2
CFG1
VOUT
VOUT
SEL
CFG2
CFG3
图5-1. 12-Ball WCSP Package (Top View)
表5-1. Pin Functions
Pin
Type Description
Name
No.
LX1
A1
Switching node of the buck stage
Supply voltage
—
VIN
EN
A2
A3
—
Device enable. A high level applied to this pin enables the device and a low level disables it. It
must not be left open.
I
GND
CFG1
B1,C1
B2
Ground
—
Configuration pin 1. Connect a resistor between this pin and ground to set VO(2) and input current
limit. Must not be left open.
I
Output voltage select. Selects VO(2) when a high level is applied to this pin. Selects VO(1) when a
low level is applied to this pin. It must not be left open.
SEL
VOUT
CFG2
LX2
B3
C2,D2
C3
I
Output voltage. The C2 and D2 pins must be connected together.
—
Configuration pin 2. Connect a resistor between this pin and ground to set VO(2) and input current
limit. Must not be left open.
I
D1
Switching node of the boost stage
—
Configuration pin 3. Connect a resistor between this pin and ground to set VO(1). Must not be left
open.
CFG3
D3
I
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
6 Specifications
6.1 Absolute Maximum Ratings
over operating junction temperature range (unless otherwise noted)(1)
MIN
–0.3
–40
–65
MAX
UNIT
V
VI
Input voltage (VIN, LX1, LX2, VOUT, EN, CFG1, CFG2, CFG3, SEL)(2)
Operating junction temperature
5.9
150
150
TJ
°C
Tstg
Storage temperature
°C
(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply
functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions. If
used outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully
functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime.
(2) All voltage values are with respect to network ground terminal, unless otherwise noted.
6.2 ESD Ratings
VALUE
±2000
±750
UNIT
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged device model (CDM), per ANSI/ESDA/JEDEC JS-002(2)
V(ESD)
Electrostatic discharge
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
1.8
1.8
5
NOM
MAX
5.5
UNIT
V
VI
Supply voltage
VO
CI
Output voltage
5.0
V
Input capacitance (VI = 2.5 V to 5 V, VO = 3.3 V, IO = 0.4 A)(1)
Output capacitance (VI = 2.5 V to 5 V, VO = 3.3 V, IO = 0.4 A)(1)
Capacitance (CFG1, CFG2, CFG3)
Inductance
µF
µF
pF
µH
CO
C(CFG)
L
10
10
2.2
Unlimited current setting
Inductor saturation current rating
2
1
ISAT
A
≤100-mA current settings
TA
TJ
Operating ambient temperature
Operating junction temperature
85
°C
°C
–40
–40
125
(1) Effective capacitance after DC bias effects have been considered.
6.4 Thermal Information
YCJ (WCSP)
12 PINS
102.4
0.6
THERMAL METRIC(1)
UNIT
RθJA
RθJC(top)
RθJB
ψJT
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
26.1
Junction-to-top characterization parameter
Junction-to-board characterization parameter
0.3
26.1
ψJB
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2022 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
6.5 Electrical Characteristics
TJ = –40°C to 125°C, VI = 3.0 V, VO = 2.5 V . Typical values are at TJ = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY
V(EN) = 3 V, no load, not switching,
"unlimited" current setting; TJ = –40°C to
85°C
IQ
Quiescent current into VIN
0.075
1
µA
ISD
Shutdown current into VIN
60
1.75
100
nA
V
V(EN) = 0 V ; TJ = –40°C to 85°C
VIT+(UVLO)
Vhys(UVLO)
VIT+(POR)
I/O SIGNALS
VIH
Positive-going UVLO threshold voltage
UVLO threshold voltage hysteresis
Positive-going POR threshold voltage
1.73
90
1.77
110
mV
V
1.37
1.74
High-level input voltage (EN, SEL)
Low-level input voltage (EN, SEL)
Input current (EN, SEL)
1.2
V
V
VIL
0.4
V(EN), V(SEL) = 1.8 V or 0 V
±1
±10
nA
POWER SWITCH
Q1
VI = 3 V, VO = 5 V, test current = 1 A
VI = 3 V, VO = 3 V, test current = 1 A
VI = 3 V, VO = 3 V, test current = 1 A
VI = 5 V, VO = 3 V, test current = 1 A
140
95
Q2
rDS(on)
On-state resistance
Q3
mΩ
95
Q4
140
CURRENT LIMIT
VI = 3.6 V,
unlimited current limit setting
Peak current limit during start-up (Q1)
0.35
1.33
0.15
0.83
1.6
A
A
VI = 1.8 V, VO = 3.6 V,
unlimited current limit setting
1.45
0.29
Peak current limit (Q1)
VI = 3.6 V, VO = 3.3 V,
100-mA current limit setting
0.51
1-mA setting
2.5-mA setting
5-mA setting
1
2.5
5
Average input current limit
10-mA settting
25-mA setting
50-mA setting
100-mA setting
10
mA
TJ = –40°C to 85°C
25
50
100
OUTPUT
Output voltage DC accuracy
Internal reference resistor
IO = 1 mA, CO(eff) = 10 µF, L(eff) = 2.2 µH
±1.5%
CONTROL
33
kΩ
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
6.5 Electrical Characteristics (continued)
TJ = –40°C to 125°C, VI = 3.0 V, VO = 2.5 V . Typical values are at TJ = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
0.1
UNIT
R2D setting #0
0
R2D setting #1
R2D setting #2
R2D setting #3
R2D setting #4
R2D setting #5
R2D setting #6
R2D setting #7
R2D setting #8
R2D setting #9
R2D setting #10
R2D setting #11
R2D setting #12
R2D setting #13
R2D setting #14
R2D setting #15
0.511
1.15
1.87
2.74
3.83
5.11
6.49
8.25
10.5
13.3
16.2
20.5
24.9
30.1
36.5
+3%
+3%
+3%
+3%
+3%
+3%
+3%
+3%
+3%
+3%
+3%
+3%
+3%
+3%
+3%
–3%
–3%
–3%
–3%
–3%
–3%
–3%
–3%
–3%
–3%
–3%
–3%
–3%
–3%
–3%
RCFG
kΩ
PROTECTION FEATURES
Thermal shutdown threshold temperature
Thermal shutdown hysteresis
TIMING PARAMETERS
140
15
150
20
160
25
°C
°C
POR signal delay after reaching POR
threshold
td(POR)
3.8
ms
Delay between a rising edge on the EN pin
and the start of the output voltage ramp
Supply voltage stable before EN pin goes
high
td(EN)
tw(SS)
1.5
ms
µs
Soft-start step duration
VO > 1.8 V
100
100
125
30
150
Delay between a change in the state of the
SEL pin and the first step change in the
output voltage
td(SEL)
40
µs
tw(DVS)
Dynamic voltage scaling step duration
Restart delay after protection
125
10
150
11
µs
td(RESTART)
ms
Copyright © 2022 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
6.6 Typical Characteristics
VO = 5.1 V
EN = HIGH
IO = 0 mA, device
not switching
VO = 5.1 V
EN = HIGH
IO = 0 mA, device
not switching
图6-2. Quiescent Current into VOUT vs Input
图6-1. Quiescent Current into VIN vs Input Voltage
Voltage
0.375
-40 C
25 C
85 C
0.325
0.275
0.225
0.175
0.125
0.075
0.025
1.8
2.3
2.8
3.3
3.8
4.3
4.8
5.3
VIN (V)
VO = 5.1 V
EN = LOW
图6-3. Shutdown Current vs Input Voltage
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
7 Detailed Description
7.1 Overview
The TPS63901 device is a four-switch synchronous buck-boost converter with a maximum output current of 400
mA. The device has a single-mode operation that allows the device to regulate the output voltage to a level
above, below, or equal to the input voltage without displaying the mode-switching transients and unpredictable
inductor current ripple from which many other buck-boost devices suffer.
The switching frequency of the TPS63901 device varies with the operating conditions: it is lowest when IO is low
and increases smoothly as IO increases.
7.2 Functional Block Diagram
EN
Enable
&
(to all blocks)
UVLO
tIL(PEAK)
t
State
Machine
Power
Stage
VOUT
Reference
Voltage
Control
Block
tVref
t
tIL(VALLEY)
t
tk‡VOt
Attenuator
Input
Current
Limit
Output
Voltage
VIN
R2D Interface
GND
7.3 Feature Description
7.3.1 Trapezoidal Current Control
图 7-1 shows a simplified block diagram of the power stage of the device. Inductor current is sensed in series
with Q1 (the peak current) and Q4 (the valley current).
Copyright © 2022 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
IL(PEAK)
IL(VALLEY)
Q1
L
Q4
CI
Q2
Q3
CO
图7-1. Power Stage Simplified Block Diagram
The device uses a trapezoidal inductor current to regulate its output under all operating conditions. Thus, the
device only has one operating mode and does not display any of the mode-change transients or unpredictable
switching displayed by many other buck-boost devices.
There are four phases of operation:
• Phase A –Q1 and Q3 are on and Q2 and Q4 are off.
• Phase B –Q1 and Q4 are on and Q2 and Q3 are off.
• Phase C –Q2 and Q4 are on and Q1 and Q3 are off.
• Phase D –Q2 and Q3 are on and Q1 and Q4 are off.
图 7-2 shows the inductor current waveform when VI > VO, 图 7-3 shows the current waveform when VI = VO,
and 图7-4 shows the current waveform when VI < VO.
图 7-2 through 图 7-4 show the typical waveforms during continuous conduction mode (CCM) switching for three
operating conditions. During discontinuous conduction mode (DCM), the typical inductor current waveforms look
similar to CCM with Phase D at 0-A inductor current. In deep boost mode, where VI << VO, Phase C length
gradually decreases to zero until the switching waveform becomes triangular.
IL(PEAK)
IL(VALLEY)
0
Time
图7-2. Inductor Current Waveform when VI > VO (CCM)
IL(PEAK)
IL(VALLEY)
0
Time
图7-3. Inductor Current Waveform when VI = VO (CCM)
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
IL(PEAK)
IL(VALLEY)
0
Time
图7-4. Inductor Current Waveform when VI < VO (CCM)
The ideal relationship between VI and VO (that is, assuming no losses) is:
tw A; + t
:
VO = VI F
w(B)G
tw(B) + tw(C)
(1)
where
• VI is the input voltage.
• VO is the output voltage.
• tw(A) is the duration of phase A.
• tw(B) is the duration of phase B.
• tw(C) is the duration of phase C.
By varying relative duration of each phase, the device can regulate VO to be less than, equal to, or greater than
VI.
7.3.2 Device Enable and Disable
The device turns on when all of the following conditions are true:
• The supply voltage is greater than the positive-going undervoltage lockout (UVLO) threshold.
• The EN pin is high.
The device turns off when at least one of the following conditions is true:
• The supply voltage is less than the negative-going UVLO threshold.
• The EN pin is low.
图7-13 shows a complete state diagram.
After the device turns on, the internal reference system starts, then the trimming information and the CFG pins
are read out. The device ignores any further changes to the CFG pins during device operation.
图7-5 shows the internal start-up sequence.
Copyright © 2022 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
VI
VIT+(POR)
EN
ttr(SS)
t
td(POR)
ttd(EN)
t
ttlim(SS)
t
ttramp(SS)t
Internal
Sequence
Power-on
reset
Start internal
reference system
Read trim bits
Read CFG pins
VO
1.2 V
图7-5. Internal Start-Up Sequence
7.3.3 Soft Start
The device has a soft-start feature that starts the device typically with 500-mA peak current limit until VO = 1.8 V
and 500 µs elapsed when the input current limit is set to unlimited (see 节 7.3.4). Afterward, the output voltage
ramps in a series of discrete steps (see 图7-6).
• When VO ≤1.8 V, peak current is limited to 500 mA typical for 500 µs.
• When VO > 1.8 V, each step is 100 mV high and has a duration of 125 µs.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
The total soft-start ramp-up time can be calculated with Equation 2.
ms
> ?
C - 1.75 ms
tr(SS)= VO × 1.25 B
W
V
(2)
where
• tr(SS) is the rise time of the output voltage in milliseconds.
• VO is the output voltage in volts.
图7-6 shows a typical start-up case.
EN
VIH
ttd(EN)
t
Internal ramp
ttr(SS)t
Target voltage
0 V
Output
Voltage
图7-6. Start-Up Behavior
图7-7 illustrates the start-up step size behavior.
t125 µst
1.8 V
t100 mVt
t500 µst
Output
Voltage
图7-7. Typical Soft-Start Ramp Step Size
表7-1 shows the typical start-up time for a number of standard output voltages.
表7-1. Typical Start-Up Times
Soft-Start Ramp-Up Start-Up Time (td(EN)
Output Voltage
Time (tr(SS)
)
+ tr(SS))
1.8 V
2.5 V
3.3 V
5 V
0.5 ms
2 ms
1.375 ms
2.375 ms
4.5 ms
2.875 ms
3.875 ms
6 ms
If the output is prebiased –that is, the initial output voltage is not zero –the start-up behavior is as follows:
• If the prebias voltage is lower than the target voltage, the device does not start switching until the ramping
output voltage is greater than the prebias voltage (see 图7-8).
• If the prebias voltage is higher than the target voltage, the device does not start to switch until the output
voltage has decreased to the target voltage (see 图7-9). The device cannot actively discharge the output to
the target voltage and relies on the load current to discharge the output capacitor and decrease the output
voltage to the target value.
Copyright © 2022 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
EN
VIH
ttd(EN)
t
Internal ramp
ttr(SS)t
Target voltage
Prebias voltage
Output
Voltage
Device not switching
Device switching
图7-8. Start-Up Behavior into Prebiased (Low) Output
EN
VIH
ttd(EN)
t
Internal ramp
ttr(SS)t
Prebias voltage
Target voltage
Output
Voltage
Device not switching
Device switching
图7-9. Start-Up Behavior into Prebiased (High) Output
7.3.4 Input Current Limit
The device can limit the current drawn from its supply, so that it can be used with batteries that do not support
high peak currents. The input current limit is active during normal operation and at start-up to avoid high inrush
current. The device has eight current limit settings:
• 1 mA
• 2.5 mA
• 5 mA
• 10 mA
• 25 mA
• 50 mA
• 100 mA
• Unlimited
CFG1 and CFG2 pins select which setting is active (see 节7.3.6).
7.3.5 Dynamic Voltage Scaling
The device has a dynamic voltage scaling function to switch between the two output voltage settings. When the
SEL pin changes state, the output voltage ramps to the new value in 100-mV steps. The duration of each step is
125 µs (see 图7-10).
The device does not actively discharge the output capacitor when the output voltage ramps to a lower level. This
leads to a longer output voltage settling time when light load is applied (see 图 7-11). The settling time can be
calculated with Equation 3.
VO(HIGH) F VO(LOW)
tsettle= CO ×
IO
(3)
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
SEL
SEL
ttd(SEL)
t
ttd(SEL)t
VO(1)
VO(1)
Output
Voltage
Output
Voltage
VO(2)
VO(2)
ttw(DVS)
t
ttw(DVS)t
t100 mVt
图7-11. Dynamic Voltage Scaling with Light Load
图7-10. Dynamic Voltage Scaling with High Load
7.3.6 Device Configuration (Resistor-to-Digital Interface)
The device has three configuration pins (CFG1, CFG2, and CFG3) that control its operation. When the device
starts up, a resistor-to-digital (R2D) interface reads the values of the configuration resistors on the CFG pins and
transfers the setting to an internal configuration register (see 图7-12).
• CFG1 and CFG2 set VO(2) level and the input current limit.
• CFG3 sets VO(1) level.
To reduce power consumption, the device reads the value of the resistors connected to the configuration pins
during start-up and then disables these pins. Once the device has started to operate, changes to the
configuration pins have no effect.
VIN
CFG[4:0]
RCFG1
RCFG2
RCFG3
CFG1
CFG2
CFG3
33 kΩ
To DVS
CFG[11:8]
12-Bit
Configuration
Register
4
MUX
ADC
To input
current
limit
CFG[7:5]
2
图7-12. Resistor-to-Digital Interface Block Diagram
表 7-2 summarizes the resistor values needed to configure the device for different input current limit and output
voltage (SEL = high) settings. For correct operation, use resistors with a tolerance of ±1% or better and a
temperature coefficient of ±200 ppm or better.
备注
For correct operation, TI recommends that the total RMS error of the configuration resistors –
including initial tolerance, temperature drift, and aging –is less than ±3%.
表7-2. Input Current Limit and Output Voltage (SEL = High) Settings
Input Current Limit
Output Voltage –VO(2)
(SEL = HIGH)
UNLIMITED
0 Ω
100 mA
511 Ω
511 Ω
50 mA
1.15 kΩ
1.15 kΩ
25 mA
10 mA
5 mA
2.5 mA
5.11 kΩ
5.11 kΩ
1 mA
RCFG1
0 Ω
1.8 V
1.9 V
RCFG2
RCFG1
RCFG2
1.87 kΩ
2.74 kΩ
3.83 kΩ
3.83 kΩ
6.49 kΩ
6.49 kΩ
511 Ω
1.87 kΩ 2.74 kΩ
0 Ω
Copyright © 2022 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
表7-2. Input Current Limit and Output Voltage (SEL = High) Settings (continued)
Input Current Limit
Output Voltage –VO(2)
(SEL = HIGH)
UNLIMITED
0 Ω
100 mA
511 Ω
50 mA
25 mA
10 mA
5 mA
2.5 mA
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
5.11 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
1 mA
RCFG1
1.15 kΩ
2.0 V
RCFG2
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
1.15 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
1.87 kΩ
2.74 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
3.83 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
6.49 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
RCFG1
1.87 kΩ
2.1 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
2.74 kΩ
2.2 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
3.83 kΩ
2.3 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
5.11 kΩ
2.4 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
6.49 kΩ
2.5 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
8.25 kΩ
2.6 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
10.5 kΩ
2.7 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
13.3 kΩ
2.8 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
16.2 kΩ
2.9 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
20.5 kΩ
3.0 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
24.9 kΩ
3.1 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
2.74 kΩ
RCFG1
30.1 kΩ
3.2 V
RCFG2
0 Ω
511 Ω
1.87 kΩ
1.87 kΩ
16.2 kΩ
2.74 kΩ
RCFG1
36.5 kΩ
3.3 V
RCFG2
0 Ω
511 Ω
2.74 kΩ
RCFG1
0 Ω
3.4 V
RCFG2
8.25 kΩ
8.25 kΩ
8.25 kΩ
8.25 kΩ
8.25 kΩ
8.25 kΩ
8.25 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
20.5 kΩ
RCFG1
511 Ω
16.2 kΩ 20.5 kΩ
1.15 kΩ
16.2 kΩ 20.5 kΩ
1.87 kΩ
16.2 kΩ 20.5 kΩ
2.74 kΩ
16.2 kΩ 20.5 kΩ
3.83 kΩ
16.2 kΩ 20.5 kΩ
5.11 kΩ
16.2 kΩ 20.5 kΩ
3.5 V
RCFG2
RCFG1
3.6 V
RCFG2
RCFG1
3.7 V
RCFG2
RCFG1
3.8 V
RCFG2
RCFG1
3.9 V
RCFG2
RCFG1
4.0 V
RCFG2
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
表7-2. Input Current Limit and Output Voltage (SEL = High) Settings (continued)
Input Current Limit
Output Voltage –VO(2)
(SEL = HIGH)
UNLIMITED
8.25 kΩ
8.25 kΩ
8.25 kΩ
8.25 kΩ
8.25 kΩ
8.25 kΩ
8.25 kΩ
8.25 kΩ
8.25 kΩ
100 mA
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
10.5 kΩ
50 mA
13.3 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
13.3 kΩ
25 mA
10 mA
5 mA
2.5 mA
30.1 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
30.1 kΩ
1 mA
RCFG1
6.49 kΩ
4.1 V
RCFG2
16.2 kΩ
20.5 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
24.9 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
36.5 kΩ
RCFG1
8.25 kΩ
4.2 V
RCFG2
16.2 kΩ
20.5 kΩ
RCFG1
10.5 kΩ
4.3 V
RCFG2
16.2 kΩ
20.5 kΩ
RCFG1
13.3 kΩ
4.4 V
RCFG2
16.2 kΩ
20.5 kΩ
RCFG1
16.2 kΩ
4.5 V
RCFG2
16.2 kΩ
20.5 kΩ
RCFG1
20.5 kΩ
4.6 V
RCFG2
16.2 kΩ
20.5 kΩ
RCFG1
24.9 kΩ
4.7 V
RCFG2
16.2 kΩ
20.5 kΩ
RCFG1
30.1 kΩ
4.8 V
RCFG2
16.2 kΩ
20.5 kΩ
RCFG1
36.5 kΩ
5.0 V
RCFG2
16.2 kΩ
20.5 kΩ
表 7-3 summarizes the resistor values needed to configure the device for different output voltage (SEL = low)
settings. For correct operation, use resistors with a tolerance of ±1% or better and a temperature coefficient of
better than ±200 ppm.
表7-3. Output Voltage (SEL Pin = Low) Settings
Output Voltage –VO(1)
RCFG3
(SEL = LOW)
1.8 V
2.0 V
2.1 V
2.2 V
2.3 V
2.4 V
2.5 V
2.6 V
2.7 V
2.8 V
3.0 V
3.3 V
3.6 V
4.0 V
4.5 V
5.0 V
0 Ω
511 Ω
1.15 kΩ
1.87 kΩ
2.74 kΩ
3.83 kΩ
5.11 kΩ
6.49 kΩ
8.25 kΩ
10.5 kΩ
13.3 kΩ
16.2 kΩ
20.5 kΩ
24.9 kΩ
30.1 kΩ
36.5 kΩ
Copyright © 2022 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
7.3.7 SEL Pin
The SEL pin selects which configuration bits control the output voltage.
• When SEL = high, the output voltage VO(2) is set.
• When SEL = low, the output voltage VO(1) is set.
7.3.8 Short-Circuit Protection
7.3.8.1 Current Limit Setting = 'Unlimited'
The device has a built-in short circuit protection function to limit the current through Q1. The maximum current
that flows is limited by the peak current limit. The output voltage decreases if the load is higher than the peak
current limit. If the output voltage falls below 1.25 typically, the short circuit protection is activated. With short
circuit protection activated, the input current is limited to 26 mA on average.
The device automatically restarts to normal operation after the short condition is removed.
7.3.8.2 Current Limit Setting = 1 mA to 100 mA
The input current limiting function automatically limits current during a short-circuit condition. The device
regulates the average input current for as long as the short-circuit condition exists. If the output voltage falls
below 1.25 V typically, the short circuit protection is activated. For input current limit settings of 100 mA, 50 mA,
and 25 mA, the short circuit protection limits the input current to 26 mA on average. For input current limit setting
of 10 mA, 5 mA, 2.5 mA, and 1 mA, the short circuit protection limits the input current to slightly above the typical
values for each setting. 表7-4 shows the typical short circuit currents for each input current limit setting.
The device automatically restarts to previous operation after the short condition is removed.
表7-4. Typical Input Current During Short Circuit Condition (VO < 1.25 V Typically) for All Input Current
Limit Settings
Input Current Limit Setting
Typical Short Circuit Input Current
1 mA
2.5 mA
5 mA
1.2 mA
2.8 mA
5.2 mA
12 mA
26 mA
26 mA
26 mA
26 mA
10 mA
25 mA
50 mA
100 mA
Unlimited
7.3.9 Thermal Shutdown
The device has a thermal shutdown function that disables the device if it gets too hot for correct operation. When
the device cools down, it automatically restarts operation after a typical delay of td(RESTART) = 10 ms. The device
starts with the soft-start feature (see 节7.3.3) and keeps the previously read CFG pin setting.
7.4 Device Functional Modes
The device has two functional modes: on and off. The device enters on mode when the voltage on the VIN pin is
higher than the UVLO threshold and a high logic level is applied to the EN pin. The device enters off mode when
the voltage on the VIN pin is lower than the UVLO threshold or a low logic level is applied to the EN pin.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
on
EN pin = high &&
VI > VIT+
EN pin = low ||
VI < VITœ
off
图7-13. Device Functional Modes
Copyright © 2022 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
8 Application and Implementation
备注
以下应用部分中的信息不属于TI 器件规格的范围,TI 不担保其准确性和完整性。TI 的客 户应负责确定
器件是否适用于其应用。客户应验证并测试其设计,以确保系统功能。
8.1 Application Information
The TPS63901 is a high-efficiency, non-inverting buck-boost converter with an extremely low quiescent current,
suitable for applications that need a regulated output voltage from an input supply that can be higher or lower
than the output voltage. The input current limit and output voltage are set through resistors connected to the
three CFGx pins.
8.2 Typical Application
L1
LX1
LX2
VO
3.3 V, 400 mA
1.8 V to 5.5 V
VIN
VOUT
10 µF
22 µF
CFG1
CFG2
CFG3
36.5 kΩ
To/from
system
EN
SEL
GND
图8-1. 3.3-VOUT Typical Application
8.2.1 Design Requirements
The design guideline provides a component selection to operate the device within the Recommended Operating
Conditions.
表8-1. Matrix of Output Capacitor and Inductor Combinations
Nominal Output Capacitor Value [µF](2)
Nominal Inductor
Value [µH](1)
10
22
47
100
≥300
(3)
(4)
(5)
2.2
+
+
+
+
+
(1) Inductor tolerance and current derating is anticipated. The effective inductance can vary by 20% and –30%.
(2) Capacitance tolerance and DC bias voltage derating is anticipated. The effective capacitance can vary by 20% and –50%.
(3) Output voltage ripple increases versus typical application.
(4) Typical application. Other check marks indicate possible filter combinations.
(5) Start-up time increased
8.2.2 Detailed Design Procedure
The first step is the selection of the output filter components. To simplify this process, the Recommended
Operating Conditions outlines minimum and maximum values for inductance and capacitance. Tolerance and
derating must be taken into account when selecting nominal inductance and capacitance.
8.2.2.1 Inductor Selection
The inductor selection is affected by several parameters such as inductor ripple current, output voltage ripple,
transition point into power save mode, and efficiency. See 表8-2 for typical inductors.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
For high efficiencies, the inductor must have a low DC resistance to minimize conduction losses. Especially at
high-switching frequencies, the core material has a high impact on efficiency. When using small chip inductors,
the efficiency is reduced mainly due to higher inductor core losses, which needs to be considered when selecting
the appropriate inductor. The inductor value determines the inductor ripple current. The larger the inductor value,
the smaller the inductor ripple current and the lower the core and conduction losses of the converter. Conversely,
larger inductor values cause a slower load transient response. To avoid saturation of the inductor, the peak
current for the inductor in steady state operation is calculated using 方程式 5. Only the equation that defines the
switch current in boost mode is shown because this provides the highest value of current and represents the
critical current value for selecting the right inductor.
V
- V
IN
OUT
V
Duty Cycle Boost
D =
OUT
(4)
(5)
Iout
η ´ (1 - D)
Vin ´ D
IPEAK
=
+
2 ´ f ´ L
where
• D is duty cycle in boost mode.
• f is the converter switching frequency.
• L is the inductor value.
• ηis the estimated converter efficiency (use the number from the efficiency curves or 0.9 as an assumption).
备注
The calculation must be done for the minimum input voltage in boost mode.
Calculating the maximum inductor current using the actual operating conditions gives the minimum saturation
current of the inductor needed. TI recommends choosing an inductor with a saturation current 20% higher than
the value calculated using 方程式5. Possible inductors are listed in 表8-2.
表8-2. List of Recommended Inductors
Inductor
Size (L × W ×
H mm)
Saturation Current [A]
Part Number
Manufacturer
DCR [mΩ]
Value [µH](1)
2.2
2.2
2.2
2.2
2.2
3.5
1.7
3.3
2.4
2.0
21
72
XFL4020-222ME
SRN3015TA-2R2M
DFE252012F-2R2M
DFE201612E-2R2M
DFE201210U-2R2M
Coilcraft
Bourns
Murata
Murata
Murata
4 × 4 × 2
3 × 3 × 1.5
82
2.5 × 2 × 1.2
2.0 × 1.6 × 1.2
2.0 × 1.2 × 1.0
116
190
(1) See the Third-party Products Disclaimer.
8.2.2.2 Output Capacitor Selection
For the output capacitor, use of small ceramic capacitors placed as close as possible to the VOUT and GND pins
of the IC is recommended. The recommended nominal output capacitor value is a single 22 µF. If, for any
reason, the application requires the use of large capacitors, which cannot be placed close to the IC, use a
smaller ceramic capacitor in parallel to the large capacitor. The small capacitor must be placed as close as
possible to the VOUT and GND pins of the IC.
It is important that the effective capacitance is given according to the recommended value in the Recommended
Operating Conditions. In general, consider DC bias effects resulting in less effective capacitance. The choice of
the output capacitance is mainly a trade-off between size and transient behavior as higher capacitance reduces
transient response overshoot and undershoot and increases transient response time. Possible output capacitors
are listed in 表8-3.
There is no upper limit for the output capacitance value.
Copyright © 2022 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
At light load currents, the output voltage ripple is dependent on the output capacitor value. Larger output
capacitors reduce the output voltage ripple. The leakage current of the output capacitor adds to the overall
quiescent current.
表8-3. List of Recommended Capacitors
Capacitor Value
Voltage Rating [V]
Part Number
Manufacturer
Size (Metric)
[µF](1)
22
6.3
6.3
6.3
GRM187R60J226ME15
GRM219R60J476ME44
GRM188R60J476ME15
Murata
Murata
Murata
0603 (1608)
0805 (3210)
0603 (1608)
22
47
(1) See the Third-party Products Disclaimer.
8.2.2.3 Input Capacitor Selection
A 10-µF input capacitor is recommended to improve line transient behavior of the regulator and EMI behavior of
the total power supply circuit. An X5R or X7R ceramic capacitor placed as close as possible to the VIN and GND
pins of the IC is recommended. This capacitance can be increased without limit. If the input supply is located
more than a few inches from the TPS63901 converter, additional bulk capacitance can be required in addition to
the ceramic bypass capacitors. An electrolytic or tantalum capacitor with a value of 47 µF is a typical choice.
When operating from a high impedance source, a larger input buffer capacitor is recommended to avoid voltage
drops during start-up and load transients.
The input capacitor can be increased without any limit for better input voltage filtering. The leakage current of the
input capacitor adds to the overall quiescent current.
表8-4. List of Recommended Capacitors
Capacitor Value
Voltage Rating [V]
Part Number
Manufacturer
Size (Metric)
[µF](1)
10
6.3
10
GRM188R60J106ME47
GRM188R61A106ME69
GRM187R60J226ME15
Murata
Murata
Murata
0603 (1608)
0603 (1608)
0603 (1608)
10
22
6.3
(1) See the Third-party Products Disclaimer.
8.2.2.4 Setting The Output Voltage
The output voltage is set with the CFGx pins (see 节7.3.6).
8.2.3 Application Curves
表8-5. Components for Application Characteristic Curves for VOUT = 3.3 V
Reference(1)
Description(2)
Part Number
Manufacturer
400-mA ultra low IQ buck-boost converter (1.5
mm × 1.15 mm)
U1
TPS63901YCJ
Texas Instruments
L1
C1
DFE252012F-2R2M
GRM188R60J106ME47
GRM187R60J226ME15
Standard
Murata
Murata
2.2 µH, 2.5 mm × 2 mm 3.3 A, 82 mΩ
10 µF, 0603, ceramic capacitor, ±20%, 6.3 V
22 µF, 0603, ceramic capacitor, ±20%, 6.3 V
36.5 kΩ, 0603 resistor, 1%, 100 mW
0 Ω, 0603 resistor, 1%, 100 mW
C2
Murata
CFG1
CFG2
CFG3
Standard
Standard
Standard
Standard
Standard
0 Ω, 0603 resistor, 1%, 100 mW
(1) See the Third-Party Products Discalimer
(2) For other output voltages, refer to 表8-1 for resistor values.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
100
90
80
70
60
50
40
100
90
80
70
60
50
40
VI = 1.8 V
VI = 2.5 V
VI = 3.0 V
VI = 3.3 V
VI = 3.6 V
VI = 5.0 V
VI = 1.8 V
VI = 2.5 V
VI = 3.0 V
VI = 3.3 V
VI = 3.6 V
VI = 5.0 V
1 µ
10 µ
100 µ
1 m
10 m
0.1
1
1 µ
10 µ
100 µ
1 m
10 m
0.1
1
Output Current (A)
Output Current (A)
VO = 1.8 V
TA = 25°C
VO = 3.3 V
TA = 25°C
图8-2. Efficiency vs Output Current
图8-3. Efficiency vs Output Current
1.2
1.1
1
100
90
80
70
60
50
40
0.9
0.8
0.7
0.6
0.5
0.4
0.3
VI = 1.8 V
VI = 2.5 V
VI = 3.0 V
VI = 3.3 V
VI = 3.6 V
VI = 5.0 V
Vo=1.8V
Vo=2.5V
Vo=3.3V
Vo=3.6V
Vo=5.0V
1.8
2.3
2.8
3.3
3.8
4.3
4.8
5.3
1 µ
10 µ
100 µ
1 m
10 m
0.1
1
Input Voltage(V)
Output Current (A)
TA = 25°C
VO = 5.0 V
TA = 25°C
图8-5. Typical Output Current Capability vs Input
图8-4. Efficiency vs Output Current
Voltage
2000000
1000000
2000000
1000000
100000
10000
1000
VO = 1.8 V
VO = 2.5 V
VO = 3.3 V
VO = 3.6 V
VO = 5.0 V
VO = 1.8 V
VO = 2.5 V
VO = 3.3 V
VO = 3.6 V
VO = 5.0 V
100000
10000
1000
100
100
10
2
10
2
1E-6
1E-5
0.0001
0.001
IO (A)
0.01
0.10.2 0.5
1E-6
1E-5
0.0001
0.001
IO (A)
0.01
0.10.2 0.5
VI = 3.3 V
TA = 25°C
VI = 2.0 V
TA = 25°C
图8-6. Typical Burst Switching Frequency vs
图8-7. Typical Burst Switching Frequency vs
Output Current
Output Current
Copyright © 2022 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
2000000
1000000
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
VO = 1.8 V
VO = 2.5 V
VO = 3.3 V
VO = 3.6 V
VO = 5.0 V
VO = 1.8 V
VO = 2.5 V
VO = 3.3 V
VO = 3.6 V
VO = 5.0 V
100000
10000
1000
100
10
2
1E-6
1E-5
0.0001
0.001
IO (A)
0.01
0.10.2 0.5
1
10
100
1 m
10 m
0.1
Output Current (A)
VI = 5.2 V
TA = 25°C
VI = 3.3 V
TA = 25°C
图8-8. Typical Burst Switching Frequency vs
图8-9. Output Voltage Ripple
Output Current
0.08
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
VO = 1.8 V
VO = 2.5 V
VO = 3.3 V
VO = 3.6 V
VO = 5.0 V
VO = 1.8 V
VO = 2.5 V
VO = 3.3 V
VO = 3.6 V
VO = 5.0 V
0.07
0.06
0.05
0.04
0.03
0.02
0.01
1
10
100
1 m
10 m
TA = 25°C
0.1
1
10
100
1 m
10 m
TA = 25°C
0.1
Output Current (A)
Output Current (A)
VI = 4.4 V
VI = 5.2 V
图8-10. Output Voltage Ripple
图8-11. Output Voltage Ripple
0.3
0.1
1.6
1.2
0.8
0.4
0
VO= 1.8V
VO= 2.5V
VO= 3.3V
VO= 3.6V
VO= 5.0V
VO= 1.8V
VO= 2.5V
VO= 3.3V
VO= 3.6V
VO= 5.0V
-0.1
-0.3
-0.5
-0.7
-0.9
-1.1
-0.4
-0.8
0
0.1
0.2
0.3
TA = 25°C
0.4
1.8
2.2
2.6
3
3.4
3.8
4.2
4.6
5
Output Current (A)
Input Voltage (V)
VI = 3.3 V
VI = 1.8 V to 5.0 V
Load = 1 mA, TA = 25°C
图8-12. Load Regulation
图8-13. Line Regulation
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
LX2
1.0V/div
Vout
1.0V/div
Vout
1.0V/div
LX1
1.0V/div
LX2
LX1
1.0V/div
1.0V/div
IL
IL
100mA/div
100mA/div
Time Scale 200ns/div
Time Scale 200ns/div
VI = 3.3 V, VO = 3.3 V
No load
VI = 1.8 V, VO = 3.3 V
No load
图8-15. Switching Waveforms, Buck-Boost
图8-14. Switching Waveforms, Boost Operation
Operation
Vout
1.0V/div
LX2
LX1
1.0V/div
1.0V/div
VIN
1V/div
VOUT 3.3V o set
50mV/div
IL
100mA/div
Time Scale 1ms/div
Time Scale 200ns/div
VI = 2.5 V to 4.2 V, VO = 3.3 V Load = 200-mA resistive load
图8-17. Line Transient, 200-mA Load
VI = 4.0 V, VO = 3.3 V
No load
图8-16. Switching Waveforms, Buck Operation
Iout
100mA/div
VIN
1V/div
Vout 3.3V o set
100mV/div
VOUT 3.3V o set
50mV/div
Time Scale 1ms/div
Time Scale 100μs/div
VI = 2.5 V to 4.2 V, VO = 3.3 V Load = 400-mA resistive load
图8-18. Line Transient, 400-mA Load
VI = 2.7 V, VO = 3.3 V
Load = 0 mA to 300 mA, tr/tf =
2 μs
图8-19. Load Transient, 300-mA Step
Copyright © 2022 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
Iout
100mA/div
Iout
100mA/div
Vout 3.3V o set
100mV/div
Vout 3.3V o set
100mV/div
Time Scale 100μs/div
Time Scale 100μs/div
VI = 3.3 V, VO = 3.3 V
Load = 0 mA to 300 mA, tr/tf =
2 μs
VI = 4.2 V, VO = 3.3 V
Load = 0 mA to 300 mA, tr/tf =
2 μs
图8-20. Load Transient, 300-mA Step
图8-21. Load Transient, 300-mA Step
VIN
1V/div
Iout
100mA/div
EN
2V/div
VOUT
1V/div
Vout 3.3V o set
100mV/div
IL
400mA/div
Time Scale 100μs/div
Time Scale 500 s/div
VI = 3.3 V, VO = 3.3 V
10-μA resistive load
VI = 5.5 V, VO = 3.3 V
Load = 0 mA to 300 mA, tr/tf =
2 μs
图8-23. Start-Up Behavior from Rising Enable
图8-22. Load Transient, 300-mA Step
VIN
1V/div
VIN
1V/div
EN
2V/div
EN
2V/div
VOUT
1V/div
VOUT
1V/div
IL
400mA/div
Iin
100mA/div
Time Scale 2ms/div
Time Scale 500 s/div
VI = 3.3 V, VO = 3.3 V
100-mA resistive load
VI = 3.3 V, VO = 3.3 V
CI = 32 μF, CO = 300 μF
图8-24. Start-Up Behavior from Rising Enable
图8-25. Start-Up with 100-mA ICL
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
VIN
1V/div
EN
VOUT
2V/div
1V/div
VIN
1V/div
VOUT
1V/div
IL
400mA/div
Iin
50mA/div
Time Scale 20 s/div
VI = 1.8 V, VO = 3.3 V
Time Scale 2ms/div
TA = 25°C
VI = 3.3 V, VO = 3.3 V
CI = 32 μF, CO = 300 μF
图8-27. Short Circuit Behavior
图8-26. Start-Up with 50-mA ICL
VIN
1V/div
VIN
1V/div
VOUT
1V/div
VOUT
1V/div
IL
400mA/div
IL
400mA/div
Time Scale 20 s/div
VI = 3.3 V, VO = 3.3 V
Time Scale 20 s/div
VI = 5.0 V, VO = 3.3 V
TA = 25°C
TA = 25°C
图8-28. Short Circuit Behavior
图8-29. Short Circuit Behavior
VIN
1V/div
VIN
1V/div
SEL
2V/div
SEL
2V/div
VOUT 2.0V o set
400mV/div
VOUT 2.0V o set
400mV/div
Time Scale 2ms/div
Time Scale 2ms/div
VI = 3.3 V, VO(1) = 2.2 V, VO(2)
3.6 V
=
VI = 3.3 V, VO(1) = 2.2 V, VO(2)
3.6 V
=
0.1-mA resistive load
400-mA resistive load
图8-30. DVS Behavior at Light Load
图8-31. DVS Behavior at High Load
Copyright © 2022 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
9 Power Supply Recommendations
The TPS63901 device is designed to operate with input supplies from 1.8 V to 5.5 V. The input supply must be
stable and free of noise to achieve the full performance of the device. If the input supply is located more than a
few centimeters away from the device, additional bulk capacitance can be required. The input capacitance
shown in the application schematics in this data sheet is sufficient for typical applications.
10 Layout
10.1 Layout Guidelines
PCB layout is an important part of any switching power supply design. A poor layout can cause unstable
operation, load regulation problems, increased ripple and noise, and EMI issues.
The following PCB layout design guidelines are recommended:
• Place the input and output capacitors close to the device.
• Minimize the area of the input loop, and use short, wide traces on the top layer to connect the input capacitor
to the VIN and GND pins.
• Minimize the area of the output loop, and use short, wide traces on the top layer to connect the output
capacitor to the VOUT and GND pins.
• The location of the inductor on the PCB is less important than the location of the input and output capacitors.
Place the inductor after the input and output capacitors have been placed close to the device. Route the
traces to the inductor on an inner layer if necessary.
10.2 Layout Example
图10-1 shows an example of a PCB layout that follows the recommendations of the previous section.
VIN
VOUT
GND
GND
L
图10-1. PCB Layout Example
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: TPS63901
TPS63901
www.ti.com.cn
ZHCSNV8A –DECEMBER 2021 –REVISED JUNE 2022
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.2 Documentation Support
11.2.1 Related Documentation
For related documentation see the following:
Texas Instruments, TPS63901 EVM User Guide
11.3 接收文档更新通知
要接收文档更新通知,请导航至 ti.com 上的器件产品文件夹。点击订阅更新 进行注册,即可每周接收产品信息更
改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
11.4 支持资源
TI E2E™ 支持论坛是工程师的重要参考资料,可直接从专家获得快速、经过验证的解答和设计帮助。搜索现有解
答或提出自己的问题可获得所需的快速设计帮助。
链接的内容由各个贡献者“按原样”提供。这些内容并不构成 TI 技术规范,并且不一定反映 TI 的观点;请参阅
TI 的《使用条款》。
11.5 Trademarks
TI E2E™ is a trademark of Texas Instruments.
所有商标均为其各自所有者的财产。
11.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.7 术语表
TI 术语表
本术语表列出并解释了术语、首字母缩略词和定义。
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2022 Texas Instruments Incorporated
28
Submit Document Feedback
Product Folder Links: TPS63901
PACKAGE OPTION ADDENDUM
www.ti.com
21-Jul-2022
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TPS63901YCJR
ACTIVE
DSBGA
YCJ
12
3000 RoHS & Green
SNAGCU
Level-1-260C-UNLIM
-40 to 125
3901
Samples
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OUTLINE
YCJ0012
DSBGA - 0.35 mm max height
SCALE 12.000
DIE SIZE BALL GRID ARRAY
A
B
E
BALL A1
CORNER
D
0.35 MAX
C
SEATING PLANE
0.05 C
BALL TYP
0.125
0.075
0.7 TYP
SYMM
D
C
1.05
TYP
SYMM
D: Max = 1.49 mm, Min = 1.43 mm
E: Max = 1.14 mm, Min = 1.08 mm
B
A
0.35
TYP
1
2
3
0.195
0.155
12X
0.35 TYP
0.015
C A B
4224964/A 04/2019
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
YCJ0012
DSBGA - 0.35 mm max height
DIE SIZE BALL GRID ARRAY
(0.35) TYP
12X ( 0.18)
1
2
3
A
(0.35) TYP
B
C
SYMM
D
SYMM
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 50X
0.0325 MIN
0.0325 MAX
METAL UNDER
SOLDER MASK
(
0.18)
METAL
EXPOSED
METAL
(
0.18)
SOLDER MASK
OPENING
EXPOSED
METAL
SOLDER MASK
OPENING
SOLDER MASK
DEFINED
(PREFERRED)
NON-SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4224964/A 04/2019
NOTES: (continued)
3. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints.
See Texas Instruments Literature No. SNVA009 (www.ti.com/lit/snva009).
www.ti.com
EXAMPLE STENCIL DESIGN
YCJ0012
DSBGA - 0.35 mm max height
DIE SIZE BALL GRID ARRAY
(0.35) TYP
(R0.05) TYP
3
12X ( 0.21)
1
2
A
(0.35) TYP
B
C
SYMM
METAL
TYP
D
SYMM
SOLDER PASTE EXAMPLE
BASED ON 0.075 mm THICK STENCIL
SCALE: 50X
4224964/A 04/2019
NOTES: (continued)
4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023,德州仪器 (TI) 公司
相关型号:
©2020 ICPDF网 联系我们和版权申明