TPS2511QDGNQ1 [TI]
USB Dedicated Charging Port Controller and Current Limiting Power Switch; USB专用充电端口控制器和限流电源开关
| 型号： | TPS2511QDGNQ1 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | USB Dedicated Charging Port Controller and Current Limiting Power Switch |
| 文件： | 总28页 (文件大小：1252K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TPS2511-Q1
www.ti.com
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
USB Dedicated Charging Port Controller and Current Limiting Power Switch
Check for Samples: TPS2511-Q1
1
FEATURES
APPLICATIONS
•
•
Qualified for Automotive Application
•
•
•
•
Vehicle USB Power Charger
AC-DC Wall Adapter with USB Port
Other USB Charger
AEC-Q100 Qualified with the Following
Results:
–
Device Temperature Grade 1: –40°C to
125°C Ambient Operating Temperature
Range
Automotive Infotainment Systems
DESCRIPTION
–
–
Device HMB ESD Classification Level H2
Device CDM ESD Classification Level C3B
The TPS2511-Q1 is a USB dedicated charging port
(DCP) controller and current limiting power switch. An
auto-detect feature monitors USB data line voltage,
and automatically provides the correct electrical
signatures on the data lines to charge compliant
devices among the following charging schemes:
•
•
Supports a DCP Shorting D+ to D–
Supports a DCP Applying 2.0 V on D+ and 2.7
V on D– (or 2.7 V on D+ and 2.0 V on D–)
•
•
Supports a DCP Applying 1.2 V on Data Lines
•
Divider DCP, required to apply 2.7 V on D+ and
2.0 V on D– or 2.0 V on D+ and 2.7 V on D–;
BC1.2 DCP, required to short D+ to D–;
1.2 V on both D+ and D–.
Automatically Switch D+ and D– Lines
Connections for an Attached Device
•
•
•
•
•
•
•
•
•
Hiccup Mode for Short-Circuit Protection
Provides CS Pin for USB Cable Compensation
Programmable Current Limit (ILIM_SET Pin)
80-mΩ typical High-Side MOSFET
The TPS2511-Q1 is a 80-mΩ power-distribution
switch intended for applications where heavy
capacitive loads and short-circuits are likely to be
encountered. This device also provides hiccup mode
when the output (OUT) voltage is less than 3.80 V
typical or when an over-temperature protection
occurs during an overload condition. Accurate and
programmable current limit provides flexibility and
convenience for applications. The TPS2511-Q1
Accurate ±10% Current-Limit at 2.3 A typical
Meets USB Power Switch Requirements
Drop-In and List of materials Compatible with
TPS2511
•
•
•
Operating Range: 4.5 V to 5.5 V
provides
a CS pin for USB cable resistance
compensation and a EN pin to turn on and turn off
the device.
Available in MSOP, 8-Pin Package
UL Listed and CB File Number E169910
SIMPLIFIED APPLICATION
5.0 VOUT
5.0 V
TPS2511-Q1
VBUS
1
2
3
4
GND
ILIM_SET
IN
OUT
DM
DP
8
7
6
5
AC-to-DC Converter
or
COUT
D-
Buck DC-to-DC
Converter
D+
GND
FB
CS
EN
CUSB
PAD
RILIM
GND
Power Supply
UDG-13098
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
TPS2511-Q1
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION(1)
ORDERABLE
DEVICE
NUMBER
TRANSPORT
MEDIA
MINIMUM
QUANTITY
TOP-SIDE
MARKING
TA = TJ
PACKAGE
PINS
Tube
80
TPS2511QDGNQ1
TPS2511QDGNRQ1
2511Q
2511Q
–40°C to 125°C
MSOP (DGN)
8
Tape and Reel
2500
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
ABSOLUTE MAXIMUM RATINGS
Over recommended junction temperature range, voltages are referenced to GND (unless otherwise noted)
MIN
–0.3
–0.3
–0.3
–7
MAX UNIT
Supply voltage range
Input voltage range
Voltage range
IN
7
7
EN, ILIM_SET
OUT, CS
7
V
7
IN to OUT
DP output voltage, DM output voltage
DP input voltage, DM input voltage
–0.3
–0.3
IN+0.3 or 5.7
IN+0.3 or 5.7
Continuous output sink current DP input current, DM input current
35
35
Continuous output source
current
DP output current, DM output current
mA
Continuous output sink current CS
10
Continuous output source
current
ILIM_SET
Internally limited
Human Body Model (HBM) QSS 009-105 (JESD22-A114A) and AEC-
Q100 Classification Level H2
2
kV
V
ESD rating
Charging Device Model (CDM) QSS 009-147 (JESD22-C101B.01)
and AEC-Q100 500V Classification Level C3B
750
Operating junction temperature, TJ
Storage temperature range, Tstg
Internally limited
150
–65
°C
THERMAL INFORMATION
TPS2511-Q1
DGN (8 PINS)
65.2
THERMAL METRIC(1)
UNITS
θJA
Junction-to-ambient thermal resistance
θJCtop
θJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
53.3
36.9
°C/W
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
3.9
ψJB
36.6
θJCbot
13.4
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
2
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links :TPS2511-Q1
TPS2511-Q1
www.ti.com
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
RECOMMENDED OPERATING CONDITIONS
voltages are referenced to GND (unless otherwise noted), positive current are into pins.
MIN
4.5
0
MAX UNIT
VIN
Input voltage of IN
5.5
5.5
V CS
VEN
VDP
VDM
IDP
Input voltage of CS
Input voltage of EN
0
5.5
5.5
5.5
±10
±10
2
V
DP data line input voltage
DM data line input voltage
Continuous sink/source current
Continuous sink/source current
Continuous sink current
0
0
IDM
mA
I CS
IOUT
RILIM_SET
TJ
Continuous output current of OUT
A resistor of current-limit, ILIM_SET to GND
Operating junction temperature
2.2
750
125
A
16.9
-40
kΩ
º C
ELECTRICAL CHARACTERISTICS
Conditions are –40°C ≤ (TJ = TA) ≤ 125°C, 4.5 V ≤ VIN ≤ 5.5 V, VEN = VIN and RILIM_SET = 22.1 kΩ. Positive current are into
pins. Typical values are at 25°C. All voltages are with respect to GND (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
POWER SWITCH
IOUT = 2 A
80
80
80
125
110
89
Static drain-source on-state
resistance
RDS(on)
IOUT = 2 A, –40ºC ≤ (TJ =TA) ≤ 85ºC
mΩ
IOUT = 2 A, TJ =TA = 25ºC
CL = 1 µF, RL = 100 Ω, VIN = 5 V see
Figure 1, Figure 3
tr
tf
OUT voltage rise time
1.0
1.5
ms
CL = 1 µF, RL = 100 Ω, VIN = 5 V see
Figure 1, Figure 3
OUT voltage fall time
0.2
0.35
0.01
0.5
2
IREV
Reverse leakage current
VOUT = 5.5 V, VIN = VEN = 0 V
µA
DISCHARGE
RDCHG
Discharge resistance
VOUT = 4 V
400
500
630
Ω
CURRENT LIMIT
RILIM_SET = 44.2 kΩ
RILIM_SET = 22.1 kΩ
RILIM_SET = 16.9 kΩ
1060
2110
2760
1160
2300
3025
1270
2550
3330
IOS
OUT short-circuit current limit
Short-circuit response time(1)
mA
µs
V
VIN = 5.0 V, RL = 50 mΩ, 2 inches lead
length, See Figure 4
tIOS
1.5
HICCUP MODE
VOUT_SHORT
OUT voltage threshold of going
into hiccup mode
On time of hiccup mode(1)
Off time of hiccup mode(1)
VIN = 5.0 V, RILIIM_SET = 210 kΩ
3.6
3.9
3.8
4.1
4.3
tOS_DEG
VIN = 5.0 V, RL = 0
VIN = 5.0 V, RL = 0
16
12
ms
s
tSC_TURN_OFF
UNDERVOLTAGE LOCKOUT
VUVLO
IN UVLO threshold voltage, rising
4.1
V
Hysteresis(1)
100
mV
SUPPLY CURRENT
IIN_OFF
VEN = 0 V, VIN = 5.5 V,
–40ºC ≤ TJ ≤ 85ºC
Disabled, IN supply current
Enabled, IN supply current
0.1
5
µA
IIN_ON
VEN = VIN, RILIM_SET = 210 kΩ
180
230
(1) Specified by design. Not production tested.
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links :TPS2511-Q1
TPS2511-Q1
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Conditions are –40°C ≤ (TJ = TA) ≤ 125°C, 4.5 V ≤ VIN ≤ 5.5 V, VEN = VIN and RILIM_SET = 22.1 kΩ. Positive current are into
pins. Typical values are at 25°C. All voltages are with respect to GND (unless otherwise noted).
PARAMETER
THERMAL SHUTDOWN
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Not in current limit
155
135
Temperature rising threshold(2)
In current limit
ºC
(2)
Hysteresis
10
OUT CURRENT DETECTION
RILIM_SET = 22.1 kΩ
RILIM_SET = 44.2 kΩ
RILIM_SET = 22.1 kΩ
RILIM_SET = 44.2 kΩ
I CS = 1 mA
1060
560
230
120
80
Load detection current threshold,
rising
IHCC_TH
mA
mA
(2)
Load detection current
Hysteresis(2)
IHCC_TH_HYS
V CS
CS output active low voltage(2)
0
140
mV
ms
CS deglitch time during turning on
tCS_EN
I CS = 1 mA
8
(2)
ENABLE INPUT (EN)
VEN_TRIP
EN threshold voltage, falling
Hysteresis
0.9
100
1.1
1.65
300
0.5
5
V
VEN_TRIP_HYS
200
mV
µA
IEN
ton
toff
Leakage current
VEN = 0 V or VEN = 5.5 V
–0.5
OUT voltage turn-on time
OUT voltage turn-off time
2.6
1.7
CL = 1 µF, RL = 100 Ω, see Figure 1,
Figure 2
ms
3
BC 1.2 DCP MODE (SHORT MODE)
RDPM_SHORT DP and DM shorting resistance
VDP = 0.8 V, IDM = 1 mA
VDP = 0.8 V
125
700
200
Ω
Resistance between DP/DM and
GND
RDCHG_SHORT
400
310
1300
kΩ
Voltage threshold on DP under
which the device goes back to
divider mode
VDPL_TH_DETACH
330
350
mV
mV
(2)
VDPL_TH_DETACH_HYS
DIVIDER MODE
VDP_2.7V
Hysteresis
50
DP output voltage
VIN = 5.0 V
VIN = 5.0 V
IDP = –5 µA
IDM = –5 µA
2.57
1.9
24
2.7
2.0
30
2.84
2.1
40
V
VDM_2.0V
DM output voltage
DP output impedance
DM output impedance
RDP_PAD1
kΩ
RDM_PAD1
24
30
40
1.2 V / 1.2 V MODE
VDP_1.2V
DP output voltage
VIN = 5.0 V
VIN = 5.0 V
IDP = –5 uA
IDM = –5 uA
1.12
1.12
80
1.2
1.2
1.28
1.28
130
130
V
V
VDM_1.2V
DM output voltage
DP output impedance
DM output impedance
RDP_PAD2
105
105
kΩ
kΩ
RDM_PAD2
80
(2) Specified by design. Not production tested.
4
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links :TPS2511-Q1
TPS2511-Q1
www.ti.com
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
OUT
RL
50%
ton
50%
VEN
CL
toff
90%
VOUT
10%
Figure 1. Output Rise and Fall Test Load
Figure 2. Enable Timing, Active High Enable
90%
IOS
VOUT
IOUT
tf
tr
10%
tIOS
Figure 3. Power-On and Off
Figure 4. Output Short-Circuit Parameters
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links :TPS2511-Q1
TPS2511-Q1
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
Current Sense
IN
CS
OUT
Current
Limit
ILIM_SET
Disable+UVLO
GND
8-ms
Deglitch
Charge
Pump
EN
Driver
UVLO
Thermal
Sense
Hiccup
CS
REF
+
S1
S2
DP
Auto
Detect
S4
S3
DM
2.0 V
2.7 V
1.2 V
+
–
+
–
+
–
+
–
UDG-12097
6
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links :TPS2511-Q1
TPS2511-Q1
www.ti.com
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
DEVICE INFORMATION
DGN PACKAGE (MSOP)
8 PINS
(Top View)
GND
ILIM_SET
IN
1
2
3
4
8
7
6
5
OUT
DM
DP
CS
EN
PIN FUNCTIONS
PIN
TYPE(1)
DESCRIPTION
NAME
NO.
Active low open -drain output, when OUT current is more than approximately half of the current limit set
by a resistor on ILIM_SET pin, the output is active low. Maximum sink current is 10 mA.
CS
4
O
I/O
I/O
I
Connected to the D– or D+ line of USB connector, provide the correct voltage with an attached portable
equipment for DCP detection, high impedance while disabled.
DM
DP
EN
7
6
5
Connected to the D+ or D– line of USB connector, provide the correct voltage with an attached portable
equipment for DCP detection, high impedance while disabled.
Logic-level control input, when it is high, turns power switch on, when it is low, turns power switch off
and turns DP and DM into the high impedance state.
GND
1
2
G
I
Ground connection.
ILIM_SET
External resistor used to set current-limiting threshold, recommended 16.9 kΩ ≤ RILIM_SET ≤ 750 kΩ.
Power supply. Input voltage connected to power switch, connect a ceramic capacitor with a value of
0.1-µF or greater from the IN pin to GND as close to the device as possible.
IN
3
8
P
OUT
O
G
Power-switch output. Connect to VBUS of USB
Ground connection.
PowerPAD
(1) G = Ground, I = Input, O = Output, P = Power
SPACER
SPACER
VIN
IOUT
0.1 mF
TPS2511-Q1
100 kW
100 kW
VBUS
D–
3
5
4
2
IN
OUT
DM
DP
8
7
6
1
EN
CS
EN
CS
RLOAD
D+
GND
ILIM_SET GND
PAD
CUSB
RILIM_SET
UDG-13100
Figure 5. Test Circuit for System Operation in Typical Characteristics Section
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links :TPS2511-Q1
TPS2511-Q1
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
www.ti.com
TYPICAL CHARACTERISTICS
4.8
8
8
4
V
= 5 V, C
= 22 mF, R
= 22.1 kW, R = 2.5 W
V
= 5 V, C
= 22 mF, R
= 22.1 kW, R = 2.5 W
ILIM_SET L
IN
OUT
ILIM_SET
L
IN
OUT
4
6
4
6
4
3.2
2.4
1.6
3.2
2.4
1.6
2
0
2
0.8
0
0
-2
-4
0.8
0
-2
-4
-6
CS
CS
OUT
EN
OUT
EN
I
I
OUT
OUT
-0.8
3m
-0.8
-9m
-7m
-5m
-3m
-1m
1m
-4m
-2m
4m
0
2m
Time - s
Time - s
Figure 6. Turn on Delay and Rise Time With 22-µF Load
Figure 7. Turn off Delay and Fall Time With 22-µF Load
6
4
6
V
= 5 V, C
= 22 mF, R
= 22.1 kW, R = 2.5 W
V
= 5 V, C
= 22 mF,
R = 2.5 W
L
IN
OUT
ILIM_SET
L
IN
OUT
4
2
2
0
0
DM
EN
OUT
DP
OUT
-2m
DP
DM
EN
-2
-2
6m
-4m
4m
0
2m
-4m
-2m
0
2m
4m
6m
Time - s
Time - s
Figure 8. Enable into 2.5-Ω Load
Figure 9. Disable with 2.5-Ω Load
8
6
4.8
4
8
4
V
= 5 V, C
= 22 mF, R
= 22.1 kW, R = 2.5 W
V
= 5 V, C
= 22 mF, R
= 22.1 kW, R = 2.5 W
ILIM_SET L
IN
OUT
ILIM_SET
L
IN
OUT
3.2
2.4
1.6
6
4
4
2
0
3.2
2.4
2
1.6
0.8
0.8
0
-2
-4
-2
0
0
-4
-6
I
V
I
V
OUT
OUT
-1m
OUT
IN
OUT
IN
-0.8
-0.8
-6m -4m -2m
0
-2m
-4m -6m
Time - s
-8m -10m -12m -14m
3m
-2m
2m
0
1m
Time - s
Figure 10. Power Up – Enabled
Figure 11. Power Down – Enabled
8
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links :TPS2511-Q1
TPS2511-Q1
www.ti.com
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
TYPICAL CHARACTERISTICS (continued)
4
4.8
4
8
8
V
= 5 V, R
= 22.1 kW, R = 2.5 W
V
= 5 V, C
= 22 mF, R
= 22.1 kW, R = 1.83 W
IN
ILIM_SET
L
IN
OUT
ILIM_SET
L
6
4
2
0
3.2
2.4
1.6
6
3.2
2.4
4
2
0
1.6
0.8
0.8
0
-2
-2
0
-4
-6
-4
-6
-0.8
-1.6
CS
OUT
22 mF
882 mF
OUT
EN
I
EN
OUT
222 mF
1542 mF
-0.8
-10m
0
10m
20m
30m
40m
-6m -4m -2m
0
2m
4m
Time - s
6m
8m 10m 12m 14m
Time - s
Figure 12. Inrush Current with Different Capacitance Load
Figure 13. Enable into 1.83-ΩLoad
8
7
3
4
V
= 5 V, C
= 22 mF, R
= 22.1 kW, R = 1 W
IN
OUT
ILIM_SET
L
V
= 5 V, C
= 22 mF, R
= 22.1 kW, R = 0 W
ILIM_SET L
IN
OUT
2.5
6
3.2
2.4
1.6
6
4
1.5
0.5
4
2
2
0.8
0
-2
-4
-0.5
-1.5
0
0
I
OUT
EN
DP
DM
I
OUT
0
NE
CS
OUT
-0.8
-2
-10m -5m
0
5m
10m
15m 20m 25m 30m 35m 40m
Time - s
-15m -10m
-5m
5m
10m
Time - s
15m
25m 30m
20m
Figure 14. Enable into 1-Ω Load
Figure 15. Enable into Short
7.5
10
9
3
2
V
= 5 V, C
= 22 mF, R
= 22.1 kW, R = 1 W
V
= 5 V, C
= 22 mF, R
= 22.1 kW, R = 1 W
IN
OUT
ILIM_SET
L
IN
OUT
ILIM_SET
L
7.5
6
8
6
4.5
3
6
4
1
4.5
3
0
1.5
0
-1
2
1.5
0
0
-1.5
-3
V
-2
-3
OUT
CS
IN
I
I
V
OUT
1
OUT
OUT
IN
-0.8
-2
-7
-3
5
9
13
-0.0004
-0.0002
0
Time - s
0.0002
0.0004
Time - s
Figure 16. 1-Ω Load Applied
Figure 17. Hiccup Mode While Enabled into 1-Ω Load
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links :TPS2511-Q1
TPS2511-Q1
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
www.ti.com
TYPICAL CHARACTERISTICS (continued)
3.2
6
4
2
3
V
= 5 V
V
V
DP
V
= 5 V, C
= 22 mF, R = 22.1 kW
ILIM_SET
IN
DM
IN
OUT
2.8
2
1
0
2.4
2
0
I
CS
OUT
1.6
-1
-2
-40
-20
0
20
40
60
80
100
120
280m
-220m
-120m
180m
-20m
80m
T
- Junction Temperature - °C
Time - s
J
Figure 18. Output Current Sensing Report
Figure 19. DP and DM Output Voltage vs Temperature
230
2.4
1.6
V
= 5 V,
R
= 16.9 kW
ILIM_SET
V
= 5 V
IN
IN
210
0.8
190
170
150
0
R
R
= 16.9 kW
= 210 kW
ILIM
ILIM
-2
-40
-20
0
20
40
60
80
100
120
-40
-20
0
20
40
60
80
100
120
T
- Junction Temperature - °C
T
J
- Junction Temperature - °C
J
Figure 20. Supply Current Disabled vs Temperature
Figure 21. Supply Current Enabled vs Temperature
3
2.8
2.6
120
100
80
V
= 5 V
R
= 20 kW
R
= 22.1 kW
ILIM_SET
V
= 5 V, I
= 2 A
OUT
IN
ILIM_SET
IN
2.4
60
2.2
2
40
-40
-20
0
20
40
60
80
100
120
-40
-20
0
20
40
60
80
100
120
T
- Junction Temperature - °C
T
J
- Junction Temperature - °C
J
Figure 22. Current Limit vs Temperature
Figure 23. Power Switch On-Resistance (RDS(ON)) vs
Temperature
10
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links :TPS2511-Q1
TPS2511-Q1
www.ti.com
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
DETAILED DESCRIPTION
Overview
The following overview references various industry standards. It is always recommended to consult the latest
standard to ensure the most recent and accurate information.
Rechargeable portable equipment requires an external power source to charge its batteries. USB ports are
convenient locations for charging because of an available 5-V power source. Universally accepted standards are
required to ensure host and client-side devices meet the power management requirements. Traditionally, USB
host ports following the USB 2.0 Specification must provide at least 500 mA to downstream client-side devices.
Because multiple USB devices can be attached to a single USB port through a bus-powered hub, it is the
responsibility of the client-side device to negotiate the power allotment from the host to guarantee the total
current draw does not exceed 500 mA. The TPS2511-Q1 provides 100 mA of current to each USB device. Each
USB device can subsequently request more current, which is granted in steps of 100 mA up 500 mA total.. The
host may grant or deny the request based on the available current.
Additionally, the success of the USB technology makes the micro-USB connector a popular choice for wall
adapter cables. This allows a portable device to charge from both a wall adapter and USB port with only one
connector.
One common difficulty has resulted from this. As USB charging has gained popularity, the 500-mA minimum
defined by the USB 2.0 Specification or 900 mA defined in the USB 3.0 Specification, has become insufficient for
many handsets, tablets and personal media players (PMP) which have a higher rated charging current. Wall
adapters and car chargers can provide much more current than 500 mA or 900 mA to fast charge portable
devices. Several new standards have been introduced defining protocol handshaking methods that allow host
and client devices to acknowledge and draw additional current beyond the 500 mA (defined in the USB 2.0
Specification) or 900 mA (defined in the USB 3.0 Specification) minimum while using a single micro-USB input
connector.
The TPS2511-Q1 supports three of the most common protocols:
•
•
•
USB Battery Charging Specification, Revision 1.2 (BC1.2)
Chinese Telecommunications Industry Standard YD/T 1591-2009
Divider Mode
In these protocols there are three types of charging ports defined to provide different charging current to client-
side devices. These charging ports are defined as:
•
•
•
Standard downstream port (SDP)
Charging downstream port (CDP)
Dedicated charging port (DCP)
The BC1.2 Specification defines a charging port as a downstream facing USB port that provides power for
charging portable equipment.
Table 1 shows different port operating modes according to the BC1.2 Specification.
Table 1. Operating Modes Table
MAXIMUM ALLOWABLE CURRENT
DRAWN
BY PORTABLE EQUIPMENT (A)
SUPPORTS USB 2.0
COMMUNICATION
PORT TYPE
SDP (USB 2.0)
SDP (USB 3.0)
CDP
Yes
Yes
Yes
No
0.5
0.9
1.5
1.5
DCP
The BC1.2 Specification defines the protocol necessary to allow portable equipment to determine what type of
port it is connected to so that it can allot its maximum allowable current drawn. The hand-shaking process is two
steps. During step one, the primary detection, the portable equipment outputs a nominal 0.6 V output on its D+
line and reads the voltage input on its D- line. The portable device concludes it is connected to a SDP if the
voltage is less than the nominal data detect voltage of 0.3 V. The portable device concludes that it is connected
to a Charging Port if the D- voltage is greater than the nominal data detect voltage of 0.3V and less than 0.8 V.
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links :TPS2511-Q1
TPS2511-Q1
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
www.ti.com
The second step, the secondary detection, is necessary for portable equipment to determine between a CDP and
a DCP. The portable device outputs a nominal 0.6 V output on its D- line and reads the voltage input on its D+
line. The portable device concludes it is connected to a CDP if the data line being remains is less than the
nominal data detect voltage of 0.3 V. The portable device concludes it is connected to a DCP if the data line
being read is greater than the nominal data detect voltage of 0.3V and less than 0.8 V.
Dedicated Charging Port (DCP)
A dedicated charging port (DCP) is a downstream port on a device that outputs power through a USB connector,
but is not capable of enumerating a downstream device, which generally allows portable devices to fast charge at
their maximum rated current. A USB charger is a device with a DCP, such as a wall adapter or car power
adapter. A DCP is identified by the electrical characteristics of its data lines. The following DCP identification
circuits are usually used to meet the handshaking detections of different portable devices.
Short the D+ Line to the D– Line
The USB BC1.2 Specification and the Chinese Telecommunications Industry Standard YD/T 1591-2009 define
that the D+ and D– data lines should be shorted together with a maximum series impedance of 200 Ω. This is
shown in Figure 24.
VBUS
VBUS
D−
5.0 V
200 W (max)
D+
GND
GND
UDG-12100
Figure 24. DCP Short Mode
Divider1 (DCP Applying 2.0 V on D+ Line and 2.7 V on D– Line) or Divider2 (DCP Applying 2.7 V on D+
Line and 2.0 V on D– Line)
There are two charging schemes for divider DCP. They are named after Divider1 and Divider2 DCPs that are
shown in Figure 25 and Figure 26. The Divider1 charging scheme is used for 5-W adapters, Divider1 applies 2.0
V to the D+ line and 2.7 V to the D– data line. The Divider2 charging scheme is used for 10-W adapters and
applies 2.7 V on the D+ line and 2.0 V is applied on the D– line.
VBUS
VBUS
VBUS
VBUS
5.0 V
5.0 V
D−
D−
D+
D+
2.7 V 2.0 V
2.0 V 2.7 V
GND
GND
+
–
+
–
+
–
+
–
UDG-12101
UDG-12102
GND
Figure 25. Divider1 DCP
GND
Figure 26. Divider2 DCP
12
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links :TPS2511-Q1
TPS2511-Q1
www.ti.com
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
Applying 1.2 V to the D+ Line and 1.2 V to the D– Line
As shown in Figure 27, some tablet USB chargers require 1.2 V on the shorted data lines of the USB connector.
The maximum resistance between the D+ line and the D- line is 200 Ω.
VBUS
VBUS
D−
5.0 V
200 W (max)
D+
GND
+
–
1.2 V
UDG-12103
GND
Figure 27. DCP Applying 1.2 V to the D+ Line and 1.2 V to the D– Line
The TPS2511-Q1 is a combination of a current-limiting USB power switch and an USB DCP identification
controller. Applications include vehicle power charger, wall adapters with USB DCP and other USB chargers.
The TPS2511-Q1 DCP controller has the auto-detect feature that monitors the D+ and D– line voltages of the
USB connector, providing the correct electrical characteristics on the DP and DM pins for the correct detections
of compliant portable devices to fast charge. These portable devices include smart phones, 5-V tablets and
personal media players.
The TPS2511-Q1 power-distribution switch is intended for applications where heavy capacitive loads and short-
circuits are likely to be encountered, incorporating a 70-mΩ, N-channel MOSFET in a single package. This
device provides hiccup mode when in current limit and OUT voltage is less than 3.8 V (typ) or an over
temperature protection occurs under an overload condition. Hiccup mode operation can reduce the output short-
circuit current down to several milliamperes. The TPS2511-Q1 provides a logic-level enable EN pin to control the
device turn-on and tuen-off and an open drain output CS for compensating VBUS to account for cable I × R
voltage loss.
DCP Auto-Detect
The TPS2511-Q1 integrates an auto-detect feature to support divider mode, short mode and 1.2 V / 1.2 V mode.
If a divider device is attached, 2.7 V is applied to the DP pin and 2.0 V is applied to the DM pin. If a BC1.2-
compliant device is attached, the TPS2511-Q1 automatically switches into short mode. If a device compliant with
the 1.2 V / 1.2 V charging scheme is attached, 1.2 V is applied on both the DP pin and the DM pin. The
functional diagram of DCP auto-detect feature is shown in Figure 28.
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links :TPS2511-Q1
TPS2511-Q1
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
www.ti.com
OUT
DM
Divider 2
5 V
8
6
VBUS
D–
S1, S2: ON
S3, S4: OFF
S1
Short Mode
S4: ON
D+
S1, S2, S3: OFF
S2
S3
S4
GND
1.2 V on DP and DM
S3, S4: ON
DP
S1, S2: OFF
7
1
2 V
2.7 V
1.2 V
+
–
+
–
+
–
GND
TPS2511-Q1
GND
UDG-13101
Figure 28. TPS2511-Q1 DCP Auto-Detect Functional Diagram
Overcurrent Protection
During an overload condition, the TPS2511-Q1 maintains a constant output current and reduces the output
voltage accordingly. If the output voltage falls below 3.8 V for 16 ms, the TPS2511-Q1 turns off the output for a
period of 12 seconds as shown in Figure 29. This operation is referred to as hiccup mode. The device stays in
hiccup mode (power cycling) until the overload condition is removed. Therefore the average output current is
significantly reduced to greatly improve the thermal stress of the device while the OUT pin is shorted.
ON
OFF
tSC_TURN_OFF
IOC
tOS_DEG
IOUT(av)
0 A
UDG-12108
Figure 29. OUT Pin Short-Circuit Current in Hiccup Mode
Two possible overload conditions can occur. In the first condition, the output has been shorted before the device
is enabled or before the voltage of IN has been applied. The TPS2511-Q1 senses the short and immediately
switches into hiccup mode of constant-current limiting. In the second condition, a short or an overload occurs
while the device is enabled. At the instant the overload occurs, high currents may flow for several microseconds
before the current-limit circuit can react. The device operates in constant-current mode for a period of 16 ms after
the current-limit circuit has responded, then switches into hiccup mode (power cycling).
14
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links :TPS2511-Q1
TPS2511-Q1
www.ti.com
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
Current-Limit Threshold
The TPS2511-Q1 has a current-limiting threshold that is externally programmed with a resistor. Equation 1 and
Figure 30 help determine the typical current-limit threshold:
51228
=
I
OS_ TYP
R
ILIM
where
•
•
IOS_TYP is in mA and RILIM is in kΩ
IOS_TYP has a better accuracy if RILIM is less than 210 kΩ
(1)
3.5
IOS_TYP
VIN = 5 V
3
2.5
2
1.5
1
0.5
0
10 60 110 160 210 260 310 360 410 460 510 560 610 660 700
Current-Limit Programming Resistor of ILIM_SET - kW
Figure 30. Typical Current Limit vs Programming Resistor
Current Sensing Report (CS)
The CS open-drain output is asserted immediately when the OUT pin current is more than about half of the
current limit set by a resistor on ILIM_SET pin. Built-in hysteresis improves the ability to resist current noise on
the OUT pin. The CS output is active low. The recommended operating sink current is less than 2 mA and
maximum sink current is 10 mA.
Undervoltage Lockout (UVLO) and Enable (EN)
The undervoltage lockout (UVLO) circuit disables the power switch and other functional circuits until the input
voltage reaches the UVLO turn-on threshold. Built-in hysteresis prevents unwanted oscillations on the output due
to input voltage drop from large current surges.
The logic input of the EN pin disables all of the internal circuitry while maintaining the power switch off. A logic-
high input on the EN pin enables the driver, control circuits, and power switch. The EN input voltage is
compatible with both TTL and CMOS logic levels.
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links :TPS2511-Q1
TPS2511-Q1
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
www.ti.com
Soft-Start, Reverse Blocking and Discharge Output
The power MOSFET driver incorporates circuitry that controls the rise and fall times of the output voltage to limit
large current and voltage surges on the input supply, and provides built-in soft-start functionality. The TPS2511-
Q1 power switch blocks current from the OUT pin to the IN pin when turned off by the UVLO or disabled. The
TPS2511-Q1 includes an output discharge function. A 500-Ω (typ.) discharge resistor dissipates stored charge
and leakage current on the OUT pin when the device is in UVLO or disabled. However as this circuit is biased
from the IN pin, the output discharge is not active when the input approaches 0 V.
Thermal Sense
The TPS2511-Q1 provides thermal protection from two independent thermal sensing circuits that monitor the
operating temperature of the power distribution switch and turn off for 12 seconds (typ) if the temperature
exceeds recommended operating conditions. The device operates in constant-current mode during an over-
current condition and OUT pin voltage is above 3.8 V (typ), which has a relatively large voltage drop across
power switch. The power dissipation in the package is proportional to the voltage drop across the power switch,
so the junction temperature rises during the over-current condition. The first thermal sensor turns off the power
switch when the die temperature exceeds 135°C and the device is within the current limit. The second thermal
sensor turns off the power switch when the die temperature exceeds 155°C regardless of whether the power
switch is in current limit. Hysteresis is built into both thermal sensors, and the switch turns on after the device
has cooled approximately 10°C. The switch continues to cycle off and on until the fault is removed.
16
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links :TPS2511-Q1
TPS2511-Q1
www.ti.com
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
APPLICATION INFORMATION
Programming the Current Limit Threshold
The user-programmable RILIM resistor on the ILIMIT_SET pin sets the current limit. The TPS2511-Q1 uses an
internal regulation loop to provide a regulated voltage on the ILIM_SET pin. The current-limiting threshold is
proportional to the current sourced out of the ILIM_SET pin. The recommended 1% resistor range for RILIM is
between 16.9 kΩ and 750 kΩ to ensure stability of the internal regulation loop, although not exceeding 210 kΩ
results in a better accuracy. Many applications require that the minimum current limit remain above a certain
current level or that the maximum current limit remain below a certain current level, so it is important to consider
the tolerance of the overcurrent threshold when selecting a value for RILIM. The Equation 2 and Equation 3
calculate the resulting overcurrent thresholds for a given external resistor value (RILIM). The traces routing the
RILIM resistor to the TPS2511-Q1 should be as short as possible to reduce parasitic effects on the current limit
accuracy. The equations and the graph below can be used to estimate the minimum and maximum variation of
the current limit threshold for a predefined resistor value. This variation disregards the inaccuracy of the resistor
itself.
51228
I
=
OS_ MIN
1.030
R
ILIM
where
•
•
IOS_MIN is in mA
RILIM is in kΩ
(2)
(3)
xxxxxx
51228
I
=
OS_MAX
0.967
R
ILIM
where
•
•
IOS_MAX is in mA
RILIM is in kΩ
600m
500m
400m
300m
200m
3.6
3
VIN = 5 V
IOS_TYP
IOS_MIN
IOS_MAX
VIN = 5 V
2.4
1.8
1.2
0.6
100m
0
IOS_TYP
20 30
IOS_MIN
40 50
IOS_MAX
60 70
0
10
100
200
300
400
500
Current Limit Programming Resistor of ILIM_SET - kW
600
700
80
90 100
Current Limit Programming Resistor of ILIM_SET - kW
Figure 31. Current Limit Threshold vs Current
Limit Resistance
Figure 32. Current Limit Threshold vs Current
Limit Resistance
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links :TPS2511-Q1
TPS2511-Q1
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
www.ti.com
Current Limit Setpoint Example
In the following example, choose the ILIM_SET resistor to ensure that TPS2511-Q1 does not trip off under worst
case conditions of current limit and resistor tolerance (assume 1% resistor tolerance). For this example, IOS_MIN
2100 mA.
51228
=
I
=
= 2100 mA
OS _MIN
1.03
ILIM
R
(4)
1
1
æ
ö1.03
÷
÷
ø
51228
51228
2100
æ
ö1.03
R
= ç
=
= 22.227 kW
ILIM
ç
÷
ç
I
è
ø
OS _MIN
è
(5)
Including resistor tolerance, target nominal resistance value:
22.227 kW
R
=
= 22.007 kW
ILIM
1.01kW
(6)
(7)
Choose:
RILIM = 22.0 kΩ
VBUS Voltage Drop Compensation
Figure 33 shows a USB charging design using the TPS2511-Q1. In general VBUS has some voltage loss due to
USB cable resistance and TPS2511-Q1 power switch on-state resistance. The sum of voltage loss is likely
several hundred millivolts from 5VOUT to VPD_IN that is the input voltage of PD while the high charging current
charges the PD. For example, in Figure 34, assuming that the loss resistance is 170 mΩ (includes 100 mΩ of
USB cable resistance and 70 mΩ of power switch resistance) and 5VOUT is 5.0 V, the input voltage of PD (VPD_IN
)
is about 4.66 V at 2.0 A. (see Figure 34)
The charging current of most portable devices is less than their maximum charging current while VPD_IN is less
than the certain voltage value. Furthermore actual charging current of PD decreases with input voltage falling.
Therefore, a portable devices cannot accomplish a fast charge with its maximum charging rated current if VBUS
voltage drop across the power path is not compensated at the high charging current. The TPS2511-Q1 provides
CS pin to report the high charging current for USB chargers to increase the 5VOUT voltage. This is shown by the
solid lines of Figure 34.
5VOUT
5.0 V
VPD_IN
100 kW
R1
TPS2511-Q1
IOUT
VBUS
1
2
3
4
GND
ILIM_SET
IN
OUT
DM
DP
8
7
6
5
IOUT
AC-to-DC Converter
or
D-
COUT
Buck DC-to-DC
Converter
R4
Portable Device
D+
R2
GND
CS
EN
Cable
FB
PAD
CUSB
0.1 mF
R3
RILIM
GND
UDG-13099
Power Supply
Figure 33. TPS2511-Q1 Charging System Schematic Diagram
18
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links :TPS2511-Q1
TPS2511-Q1
www.ti.com
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
5.25
5.15
5.00
4.75
4.66
5 VOUT with compensation
VPD_IN with compensation
5 VOUT without compensation
VPD_IN without compensation
0
0.5
1.0
1.5
2.0
2.5
Output Current (A)
UDG-12109
Figure 34. TPS2511-Q1 CS Function
Equation 8 through Equation 11 refer to Figure 33.
The power supply output voltage is calculated in Equation 8.
R +R +R ´ V
FB
(
)
1
2
3
5V
=
OUT
R
3
(8)
5VOUT and VFB are known. If R3 is given and R1 is fixed, R2 can be calculated. The 5VOUT voltage change with
compensation is shown in Equation 9 and Equation 10.
R +R ´R ´ V
FB
(
)
R ´R
2
3
1
DV =
3
4
(9)
æ 5V
R ö R ´ V
1 1 FB
OUT
ΔV =
-
ç
÷
V
R
R
4
è
FB
3 ø
If R1 is less than R3, then Equation 10 can be simplified as Equation 11.
5V ´ R
(10)
OUT
1
DV »
R
4
(11)
Divide Mode Selection of 5-W and 10-W USB Chargers
The TPS2511-Q1 provides two types of connections between the DP pin and the DM pin and between the D+
data line and the D– data line of the USB connector for a 5-W USB charger and a 10-W USB charger with a
single USB port. For a 5-W USB charger, the DP pin is connectd to the D– line and the DM pin is connected to
the D+ line. This is shown in Figure 37 and Figure 38. It is necessary to apply DP and DM to D+ and D– of USB
connector for 10-W USB chargers. See Figure 35 and Figure 36. Table 2. shows different charging schemes for
both 5-W and 10-W USB charger solutions
Table 2. Charging Schemes for 5-W and 10-W USB Chargers
USB CHARGER TYPE
CONTAINING CHARGING SCHEMES
1.2 V on both D+ and D– Lines
1.2 V on both D+ and D– Lines
5-W
Divider1
Divider2
BC1.2 DCP
BC1.2 DCP
10-W
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links :TPS2511-Q1
TPS2511-Q1
SLUSBK5A –JUNE 2013–REVISED JUNE 2013
www.ti.com
TPS2511-Q1
5.0 V
VBUS
D-
TPS2511-Q1
Power
Supply
3
5
4
2
IN
OUT
DM
DP
8
7
6
1
5.0 V
Power
Supply
VBUS
3
5
4
2
IN
OUT
DM
DP
8
7
6
1
EN
CS
D-
EN
CS
D+
D+
GND
ILIM_SET GND
PAD
GND
ILIM_SET GND
PAD
RILIM
RILIM
UDG-13102
UDG-13103
Figure 35. 10-W USB Charger Application
with Power Switch
Figure 36. 10-W USB Charger Application
without Power Switch
TPS2511-Q1
5.0 V
Power
Supply
VBUS
TPS2511-Q1
3
5
4
2
IN
OUT
DM
DP
8
7
6
1
5.0 V
Power
Supply
VBUS
3
5
4
2
IN
OUT
DM
DP
8
7
6
1
D-
EN
CS
D-
EN
CS
D+
D+
GND
ILIM_SET GND
PAD
GND
ILIM_SET GND
PAD
RILIM
RILIM
UDG-13104
UDG-13105
Figure 37. 5-W USB Charger Application
with Power Switch
Figure 38. 5-W USB Charger Application
without Power Switch
Layout Guidelines
•
TPS2511-Q1 placement. Place the TPS2511-Q1 near the USB output connector and at lest 22-µF OUT pin
filter capacitor. Connect the exposed Power PAD to the GND pin and to the system ground plane using a via
array.
•
•
IN pin bypass capacitance. Place the 0.1-µF bypass capacitor near the IN pin and make the connection
using a low-inductance trace.
ILIM_SET pin connection. Current limit set point accuracy can be compromised by stray leakage from a
higher voltage source to the ILIM_SET pin. Ensure that there is adequate spacing between IN pin
copper/trace and ILIM_SET pin trace to prevent contaminant buildup during the PCB assembly process. The
traces routing the RILIM resistor to the device should be as short as possible to reduce parasitic effects on the
current-limit accuracy.
20
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links :TPS2511-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jul-2013
PACKAGING INFORMATION
Orderable Device
TPS2511QDGNQ1
TPS2511QDGNRQ1
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
ACTIVE
MSOP-
PowerPAD
DGN
8
8
80
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
2511Q
2511Q
ACTIVE
MSOP-
DGN
2500
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
-40 to 125
PowerPAD
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jul-2013
OTHER QUALIFIED VERSIONS OF TPS2511-Q1 :
Catalog: TPS2511
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Jul-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS2511QDGNRQ1
MSOP-
Power
PAD
DGN
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Jul-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
MSOP-PowerPAD DGN
SPQ
Length (mm) Width (mm) Height (mm)
366.0 364.0 50.0
TPS2511QDGNRQ1
8
2500
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明