TPS2013APWPRG4 [TI]
POWER-DISTRIBUTION SWITCHES; 配电开关型号: | TPS2013APWPRG4 |
厂家: | TEXAS INSTRUMENTS |
描述: | POWER-DISTRIBUTION SWITCHES |
文件: | 总29页 (文件大小:1236K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
POWER-DISTRIBUTION SWITCHES
1
FEATURES
•
33-mΩ (5-V Input) High-Side MOSFET Switch
•
•
•
•
•
•
•
•
Short-Circuit and Thermal Protection
Operating Range . . . 2.7 V to 5.5 V
Logic-Level Enable Input
Typical Rise Time. . . 6.1 ms
Undervoltage Lockout
Maximum Standby Supply Current. . . 10 μA
No Drain-Source Back-Gate Diode
Available in 8-pin SOIC and 14-Pin TSSOP
Packages
•
•
Ambient Temperature Range, –40°C to 85°C
2-kV Human-Body-Model, 200-V
Machine-Model ESD Protection
DESCRIPTION
The TPS201xA family of power distribution switches is intended for applications where heavy capacitive loads
and short circuits are likely to be encountered. These devices are 50-mΩ N-channel MOSFET high-side power
switches. The switch is controlled by a logic enable compatible with 5-V logic and 3-V logic. Gate drive is
provided by an internal charge pump designed to control the power-switch rise times and fall times to minimize
current surges during switching. The charge pump requires no external components and allows operation from
supplies as low as 2.7 V.
When the output load exceeds the current-limit threshold or a short is present, the TPS201xA limits the output
current to a safe level by switching into a constant-current mode. When continuous heavy overloads and short
circuits increase the power dissipation in the switch, causing the junction temperature to rise, a thermal
protection circuit shuts off the switch to prevent damage. Recovery from a thermal shutdown is automatic once
the device has cooled sufficiently. Internal circuitry ensures the switch remains off until valid input voltage is
present.
TPS2014 600 mA
TPS201xA 0.2 A - 2 A
TPS2015 1 A
TPS202x
TPS203x
0.2 A - 2 A
0.2 A - 2 A
TPS2041B 500 mA
TPS2051B 500 mA
TPS2045A 250 mA
TPS2049 100 mA
TPS2055A 250 mA
TPS2061 1 A
TPS2065 1 A
TPS2068 1.5 A
TPS2069 1.5 A
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1998–2007, Texas Instruments Incorporated
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
DESCRIPTION (CONTINUED)
The TPS201xA devices differ only in short-circuit current threshold. The TPS2010A limits at 0.3-A load, the
TPS2011 at 0.9-A load, the TPS2012A at 1.5-A load, and the TPS2013A at 2.2-A load (see Available Options).
The TPS201xA is available in an 8-pin small-outline integrated-circuit (SOIC) package and in a 14-pin thin-shrink
small-outline package (TSSOP) and operates over a junction temperature range of -40°C to 125°C.)
AVAILABLE OPTIONS
RECOMMENDED
MAXIMUM CONTINUOUS
LOAD CURRENT
(A)
PACKAGED DEVICES(1)
TYPICAL SHORT-CIRCUIT
CURRENT LIMIT AT 25°C
(A)
SMALL OUTLINE
TSSOP
TA
ENABLE
(D)(2)
(PWP)(3)
0.2
0.6
1
0.3
0.9
1.5
2.2
TPS2010AD
TPS2011AD
TPS2012AD
TPS2013AD
TPS2010APWPR
TPS2011APWPR
TPS2012APWPR
TPS2013APWPR
–40°C to 85°C
Active low
1.5
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
(2) The D package is available taped and reeled. Add an R suffix to device type (e.g., TPS2010DR)
(3) The PWP package is only available left-end taped-and-reeled.
TPS201xA FUNCTIONAL BLOCK DIAGRAM
TERMINAL FUNCTIONS
TERMINAL
NO.
I/O
DESCRIPTION
NAME
D
4
PWP
7
EN
I
I
Enable input. Logic low turns on power switch.
GND
IN
1
1
Ground
2, 3
5–8
2–6
8–14
I
Input voltage
Power-switch output
OUT
O
2
Submit Documentation Feedback
Copyright © 1998–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
DETAILED DESCRIPTION
POWER SWITCH
The power switch is an N-channel MOSFET with a maximum on-state resistance of 50 mΩ (VI(IN) = 5V).
Configured as a high-side switch, the power switch prevents current flow from OUT to IN and IN to OUT when
disabled.
CHARGE PUMP
An internal charge pump supplies power to the driver circuit and provides the necessary voltage to pull the gate
of the MOSFET above the source. The charge pump operates from input voltages as low as 2.7 V and requires
very little supply current.
DRIVER
The driver controls the gate voltage of the power switch. To limit large current surges and reduce the associated
electromagnetic interference (EMI) produced, the driver incorporates circuitry that controls the rise times and fall
times of the output voltage. The rise and fall times are typically in the 2-ms to 9-ms range.
ENABLE (EN)
The logic enable disables the power switch, the bias for the charge pump, driver, and other circuitry to reduce the
supply current to less than 10 μA when a logic high is present on EN . A logic zero input on EN restores bias to
the drive and control circuits and turns the power on. The enable input is compatible with both TTL and CMOS
logic levels.
CURRENT SENSE
A sense FET monitors the current supplied to the load. The sense FET measures current more efficiently than
conventional resistance methods. When an overload or short circuit is encountered, the current-sense circuitry
sends a control signal to the driver. The driver, in turn, reduces the gate voltage and drives the power FET into
its saturation region, which switches the output into a constant current mode and holds the current constant while
varying the voltage on the load.
THERMAL SENSE
An internal thermal-sense circuit shuts off the power switch when the junction temperature rises to approximately
140°C. Hysteresis is built into the thermal sense circuit. After the device has cooled approximately 20°C, the
switch turns back on. The switch continues to cycle off and on until the fault is removed.
UNDERVOLTAGE LOCKOUT
A voltage sense circuit monitors the input voltage. When the input voltage is below approximately 2 V, a control
signal turns off the power switch.
Copyright © 1998–2007, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)(1)
VALUE
–0.3 to 6
UNIT
VI(IN)
Input voltage range(2)
Output voltage range(2)
V
V
V
VO(OUT)
VI(EN)
–0.3 to VI(IN) + 0.3
–0.3 to 6
Input voltage range
IO(OUT)
Continuous output current
Internally Limited
Continuous total power dissipation
Operating virtual junction temperature range
Storage temperature range
See Dissipation Rating Table
TJ
–40 to 125
°C
°C
°C
kV
V
Tstg
–65 to 150
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds
260
2
Human body model
Electrostatic discharge protection
Machine model
ESD
200
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to GND.
DISSIPATION RATINGS
T
A ≤ 25°C
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
PACKAGE
POWER RATING
D
725 mW
5.8 mW/°C
5.6 mW/°C
464 mW
448 mW
377 mW
364 mW
PWP
700 mW
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
2.7
0
MAX
5.5
5.5
0.2
0.6
1
UNIT
VI(IN)
Input voltage
VIH
V
TPS2010A
TPS2011A
0
0
IO
Continuous output current
A
TPS2012A
TPS2013A
0
0
1.5
125
TJ
Operating virtual junction temperature
–40
°C
4
Submit Documentation Feedback
Copyright © 1998–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
ELECTRICAL CHARACTERISTICS
over recommended operating junction temperature range, VI(IN) = 5.5 V, IO = rated current, EN = 0 V (unless otherwise noted)
PARAMETER
POWER SWITCH
TEST CONDITIONS(1)
MIN
TYP
MAX UNIT
VI(IN) = 5 V,
TJ = 25°C,
TJ = 85°C,
TJ = 125°C,
TJ = 25°C,
TJ = 85°C,
TJ = 125°C,
TJ = 25°C,
TJ = 85°C,
TJ = 125°C,
TJ = 25°C,
TJ = 85°C,
TJ = 125°C,
TJ = 25°C,
TJ = 25°C,
TJ = 25°C,
TJ = 25°C,
IO = 1.5 A
IO = 1.5 A
IO = 1.5 A
IO = 1.5 A
IO = 1.5 A
IO = 1.5 A
IO = 0.18 A
IO = 0.18 A
IO = 0.18 A
IO = 0.18 A
IO = 0.18 A
IO = 0.18 A
CL = 1 μF,
CL = 1 μF,
CL = 1 μF,
CL = 1 μF,
33
38
44
37
43
51
30
35
39
33
39
44
6.1
8.6
3.4
3
36
46
VI(IN) = 5 V,
VI(IN) = 5 V,
50
TPS2013A
TPS2010A
mΩ
41
VI(IN) = 3.3 V,
VI(IN) = 3.3 V,
VI(IN) = 3.3 V,
VI(IN) = 5 V,
52
61
34
41
Static drain-source on-state
resistance
rDS(on)
VI(IN) = 5 V,
VI(IN) = 5 V,
47
mΩ
37
VI(IN) = 3.3 V,
VI(IN) = 3.3 V,
VI(IN) = 3.3 V,
VI(IN) = 5.5 V,
VI(IN) = 2.7 V,
VI(IN) = 5.5 V,
VI(IN) = 2.7 V,
46
56
RL = 10 Ω
RL = 10 Ω
RL = 10 Ω
RL = 10 Ω
tr
tf
Rise time, output
Rise time, output
ms
ms
ENABLE INPUT (EN)
VIH
High-level input voltage
2.7 V ≤ VI(IN) ≤ 5.5 V
4.5 V ≤ VI(IN) ≤ 5.5 V
2.7 V ≤ VI(IN) ≤ 4.5 V
EN = 0 V or EN = VI(IN)
CL = 100 μF,
2
V
0.8
V
VIL
Low-level input voltage
0.5
II
Input current
Turnon time
Turnoff time
–0.5
0.5
20
40
μA
ms
ms
ton
toff
RL = 10 Ω
RL = 10 Ω
CL = 100 μF,
CURRENT LIMIT
TPS2010A
TPS2011A
TPS2012A
TPS2013A
0.22
0.66
1.1
0.3
0.9
1.5
2.2
0.4
1.1
1.8
2.7
TJ = 25°C, VI = 5.5 V,
OUT connected to GND,
Device enable into short circuit
IOS
Short-circuit output current
A
1.65
(1) Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account
separately.
Copyright © 1998–2007, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
ELECTRICAL CHARACTERISTICS (Continued)
over recommended operating junction temperature range, VI(IN) = 5.5 V, IO = rated current, EN = 0 V (unless otherwise noted)
PARAMETER
SUPPLY CURRENT
TEST CONDITIONS(1)
MIN TYP MAX UNIT
TJ = 25°C
0.3
1
10
75
Supply current, low-level output
Supply current, high-level output
No Load on OUT
No Load on OUT
EN = VI(IN)
EN = 0 V
μA
–40°C ≤ TJ ≤ 125°C
TJ = 25°C
58
μA
μA
–40°C ≤ TJ ≤ 125°C
–40°C ≤ TJ ≤ 125°C
75 100
10
Leakage current
OUT connected to ground EN = VI(IN)
UNDERVOLTAGE LOCKOUT
Low-level input voltage
Hysteresis
2
2.5
V
TJ = 25°C
100
mV
(1) Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account
separately.
6
Submit Documentation Feedback
Copyright © 1998–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
PARAMETER MEASUREMENT INFORMATION
Figure 1. Test Circuit and Voltage Waveforms
Table 1. Timing Diagrams
FIGURE
Turnon Delay and Rise Time
Turnoff Delay and Fall Time
2
3
Turnon Delay and Rise TIME with 1-μF Load
4
Turnoff Delay and Rise TIME with 1-μF Load
5
Device Enabled into Short
6
TPS2010A, TPS2011A, TPS2012A, and TPS2013A, Ramped Load on Enabled Device
TPS2013A, Inrush Current
7, 8, 9, 10
11
12
13
14
15
16
17
18
19
7.9-Ω Load Connected to an Enabled TPS2010A Device
3.7-Ω Load Connected to an Enabled TPS2010A Device
3.7-Ω Load Connected to an Enabled TPS2011A Device
2.6-Ω Load Connected to an Enabled TPS2011A Device
2.6-Ω Load Connected to an Enabled TPS2012A Device
1.2-Ω Load Connected to an Enabled TPS2012A Device
1.2-Ω Load Connected to an Enabled TPS2013A Device
0.9-Ω Load Connected to an Enabled TPS2013A Device
Copyright © 1998–2007, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
Figure 2. Turnon Delay and Rise Time
Figure 3. Turnoff Delay and Fall Time
Figure 4. Turnon Delay and Rise Time With 1-μF Load
Figure 5. Turnoff Delay and Fall Time With 1-μF Load
8
Submit Documentation Feedback
Copyright © 1998–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
Figure 6. Device Enabled Into Short
Figure 7. TPS2010A, Ramped Load on Enabled Device
Figure 8. TPS2011A, Ramped Load on Enabled Device
Figure 9. TPS2012A, Ramped Load on Enabled Device
Copyright © 1998–2007, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
Figure 10. TPS2013A, Ramped Load on Enabled Device
Figure 11. TPS2013A, Inrush Current
Figure 12. 7.9-Ω Load Connected to an Enabled
Figure 13. 3.7-Ω Load Connected to an Enabled
TPS2010A Device
TPS2010A Device
10
Submit Documentation Feedback
Copyright © 1998–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
Figure 14. 3.7-Ω Load Connected to an Enabled
Figure 15. 2.6-Ω Load Connected to an Enabled
TPS2011A Device
TPS2011A Device
Figure 16. 2.6-Ω Load Connected to an Enabled
Figure 17. 1.2-Ω Load Connected to an Enabled
TPS2012A Device
TPS2012A Device
Copyright © 1998–2007, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
Figure 18. 1.2-Ω Load Connected to an Enabled TPS2013A Device
Figure 19. 0.9-Ω Load Connected to an Enabled TPS2013A Device
12
Submit Documentation Feedback
Copyright © 1998–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
20
td(on)
td(off)
tr
Turnon delay time
vs Output voltage
Turnoff delay time
vs Input voltage
21
Rise time
vs Load current
22
tf
Fall time
vs Load current
23
Supply current (enabled)
Supply current (disabled)
Supply current (enabled)
Supply current (disabled)
Short-circuit current limit
vs Junction temperature
vs Junction temperature
vs Input voltage
24
25
26
vs Input voltage
27
IOS
vs Input voltage
28
vs Junction temperature
vs Input voltage
29
rDS(on)
Static drain-source on-state resistance
30
vs Junction temperature
vs Input voltage
31
32
vs Junction temperature
Input voltage vs Temperature
33
Undervoltage lockout
34
TURNON DELAY TIME
vs
OUTPUT VOLTAGE
TURNOFF DELAY TIME
vs
INPUT VOLTAGE
Figure 20.
Figure 21.
Copyright © 1998–2007, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
RISE TIME
vs
LOAD CURRENT
FALL TIME
vs
LOAD CURRENT
Figure 22.
Figure 23.
SUPPLY CURRENT (ENABLED)
vs
JUNCTION TEMPERATURE
SUPPLY CURRENT (DISABLED)
vs
JUNCTION TEMPERATURE
Figure 24.
Figure 25.
14
Submit Documentation Feedback
Copyright © 1998–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
SUPPLY CURRENT (ENABLED)
SUPPLY CURRENT (DISABLED)
vs
vs
INPUT VOLTAGE
INPUT VOLTAGE
Figure 26.
Figure 27.
SHORT-CIRCUIT CURRENT LIMIT
SHORT-CIRCUIT CURRENT LIMIT
vs
vs
INPUT VOLTAGE
JUNCTION TEMPERATURE
Figure 28.
Figure 29.
Copyright © 1998–2007, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
vs
INPUT VOLTAGE
JUNCTION TEMPERATURE
Figure 30.
Figure 31.
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
vs
INPUT VOLTAGE
JUNCTION TEMPERATURE
Figure 32.
Figure 33.
16
Submit Documentation Feedback
Copyright © 1998–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
UNDERVOLTAGE LOCKOUT
Figure 34.
Copyright © 1998–2007, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
APPLICATION INFORMATION
Figure 35. Typical Application
POWER-SUPPLY CONSIDERATIONS
A 0.01-μF to 0.1-μF ceramic bypass capacitor between IN and GND, close to the device, is recommended.
Placing a high-value electrolytic capacitor on the output and input pins is recommended when the output load is
heavy. This precaution reduces power supply transients that may cause ringing on the input. Additionally,
bypassing the output with a 0.01-μF to 0.1-μF ceramic capacitor improves the immunity of the device to
short-circuit transients.
OVERCURRENT
A sense FET checks for overcurrent conditions. Unlike current-sense resistors, sense FETs do not increase the
series resistance of the current path. When an overcurrent condition is detected, the device maintains a constant
output current and reduces the output voltage accordingly. Complete shutdown occurs only if the fault is present
long enough to activate thermal limiting.
Three possible overload conditions can occur. In the first condition, the output has been shorted before the
device is enabled or before VI(IN) has been applied (see Figure 6). The TPS201xA senses the short and
immediately switches into a constant-current output.
In the second condition, the excessive load occurs while the device is enabled. At the instant the excessive load
occurs, very high currents may flow for a short time before the current-limit circuit can react (see
Figure 12–Figure 19). After the current-limit circuit has tripped (reached the overcurrent trip threshold) the device
switches into constant-current mode.
In the third condition, the load has been gradually increased beyond the recommended operating current. The
current is permitted to rise until the current-limit threshold is reached or until the thermal limit of the device is
exceeded (see Figures Figure 77–Figure 10). The TPS201xA is capable of delivering current up to the
current-limit threshold without damaging the device. Once the threshold has been reached, the device switches
into its constant-current mode.
POWER DISSIPATION AND JUNCTION TEMPERATURE
The low on-resistance on the n-channel MOSFET allows small surface-mount packages, such as SOIC, to pass
large currents. The thermal resistance of these packages are high compared to those of power packages; it is
good design practice to check power dissipation and junction temperature. The first step is to find rDS(on) at the
input voltage and operating temperature. As an initial estimate, use the highest operating ambient temperature of
interest and read rDS(on) from SLVS1892074Figure 30–Figure 33 . Next, calculate the power dissipation using:
2
P
+ r
I
D
DS(on)
(1)
(2)
Finally, calculate the junction temperature:
T + P R ) T
J
D
qJA
A
18
Submit Documentation Feedback
Copyright © 1998–2007, Texas Instruments Incorporated
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
TPS2010A, TPS2011A
TPS2012A, TPS2013A
www.ti.com
SLVS189C–DECEMBER 1998–REVISED SEPTEMBER 2007
Where:
TA = Ambient Temperature °C
θJA = Thermal resistance SOIC = 172°C/W
R
Compare the calculated junction temperature with the initial estimate. If they do not agree within a few degrees,
repeat the calculation, using the calculated value as the new estimate. Two or three iterations are generally
sufficient to get an acceptable answer.
THERMAL PROTECTION
Thermal protection prevents damage to the IC when heavy-overload or short-circuit faults are present for
extended periods of time. The faults force the TPS201xA into constant current mode, which causes the voltage
across the high-side switch to increase; under short-circuit conditions, the voltage across the switch is equal to
the input voltage. The increased dissipation causes the junction temperature to rise to high levels. The protection
circuit senses the junction temperature of the switch and shuts it off. Hysteresis is built into the thermal sense
circuit, and after the device has cooled approximately 20 degrees, the switch turns back on. The switch continues
to cycle in this manner until the load fault or input power is removed.
UNDERVOLTAGE LOCKOUT (UVLO)
An undervoltage lockout ensures that the power switch is in the off state at power up. Whenever the input
voltage falls below approximately 2 V, the power switch will be quickly turned off. This facilitates the design of
hot-insertion systems where it is not possible to turn off the power switch before input power is removed. The
UVLO will also keep the switch from being turned on until the power supply has reached at least 2 V, even if the
switch is enabled. Upon reinsertion, the power switch will be turned on, with a controlled rise time to reduce EMI
and voltage overshoots.
GENERIC HOT-PLUG APPLICATIONS (see Figure 36)
In many applications it may be necessary to remove modules or p-c boards while the main unit is still operating.
These are considered hot-plug applications. Such implementations require the control of current surges seen by
the main power supply and the card being inserted. The most effective way to control these surges is to limit and
slowly ramp the current and voltage being applied to the card, similar to the way in which a power supply
normally turns on. Because of the controlled rise times and fall times of the TPS201xA series, these devices can
be used to provide a softer start-up to devices being hot-plugged into a powered system. The UVLO feature of
the TPS201xA also ensures the switch will be off after the card has been removed, and the switch will be off
during the next insertion. The UVLO feature guarantees a soft start with a controlled rise time for every insertion
of the card or module.
Figure 36. Typical Hot-Plug Implementation
By placing the TPS201xA between the VCC input and the rest of the circuitry, the input power will reach this
device first after insertion. The typical rise time of the switch is approximately 9 ms, providing a slow voltage
ramp at the output of the device. This implementation controls system surge currents and provides a
hot-plugging mechanism for any device.
Copyright © 1998–2007, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s): TPS2010A, TPS2011A TPS2012A, TPS2013A
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2011
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
TPS2010AD
TPS2010ADG4
TPS2010ADR
TPS2010ADRG4
TPS2011AD
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
D
D
8
8
75
75
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
CU NIPDAU Level-1-260C-UNLIM
SOIC
D
8
2500
2500
75
Green (RoHS
& no Sb/Br)
SOIC
D
8
Green (RoHS
& no Sb/Br)
SOIC
D
8
Green (RoHS
& no Sb/Br)
TPS2011ADG4
TPS2011ADR
TPS2011ADRG4
TPS2011APWP
TPS2011APWPG4
TPS2012AD
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
SOIC
D
8
2500
2500
90
Green (RoHS
& no Sb/Br)
SOIC
D
8
Green (RoHS
& no Sb/Br)
HTSSOP
HTSSOP
SOIC
PWP
PWP
D
14
14
8
Green (RoHS
& no Sb/Br)
90
Green (RoHS
& no Sb/Br)
75
Green (RoHS
& no Sb/Br)
TPS2012ADG4
TPS2012ADR
TPS2012ADRG4
TPS2013AD
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
SOIC
D
8
2500
2500
75
Green (RoHS
& no Sb/Br)
SOIC
D
8
Green (RoHS
& no Sb/Br)
SOIC
D
8
Green (RoHS
& no Sb/Br)
TPS2013ADG4
TPS2013ADR
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2011
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
TPS2013ADRG4
TPS2013APWP
SOIC
D
8
2500
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
HTSSOP
HTSSOP
HTSSOP
HTSSOP
PWP
PWP
PWP
PWP
14
14
14
14
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
TPS2013APWPG4
TPS2013APWPR
TPS2013APWPRG4
90
Green (RoHS
& no Sb/Br)
2000
2000
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS2010ADR
TPS2011ADR
TPS2012ADR
TPS2013ADR
TPS2013APWPR
SOIC
SOIC
SOIC
SOIC
D
D
D
D
8
8
2500
2500
2500
2500
2000
330.0
330.0
330.0
330.0
330.0
12.4
12.4
12.4
12.4
12.4
6.4
6.4
6.4
6.4
6.9
5.2
5.2
5.2
5.2
5.6
2.1
2.1
2.1
2.1
1.6
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
8
8
HTSSOP PWP
14
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS2010ADR
TPS2011ADR
TPS2012ADR
TPS2013ADR
TPS2013APWPR
SOIC
SOIC
D
D
8
8
2500
2500
2500
2500
2000
340.5
340.5
340.5
340.5
367.0
338.1
338.1
338.1
338.1
367.0
20.6
20.6
20.6
20.6
35.0
SOIC
D
8
SOIC
D
8
HTSSOP
PWP
14
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号:
TPS2013DG4
2.6A, 2.7 to 5.5V Single High-Side MOSFET Switch IC, No Fault Reporting, Active-Low Enable 8-SOIC -40 to 85
TI
TPS2013PWLE
2.6A, 2.7 to 5.5V Single High-Side MOSFET Switch IC, No Fault Reporting, Active-Low Enable 14-TSSOP
TI
©2020 ICPDF网 联系我们和版权申明